Upload
others
View
11
Download
0
Embed Size (px)
Citation preview
WGSW-20160HP
16-Port Gigabit 802.3at PoE+ 4G TP/SFP Combo Managed Switch
WGSW-24040HP
24-Port 10/100/1000Mbps 802.3at PoEwith 4 Shared SFP Managed Switch
WGSW-24040HP4
24-Port 10/100/1000Mbps 802.3at PoEwith 4 Shared SFP Managed Switch (440W)
Quick Installation Guide
Table of Contents
1. Package Content ......................................................................................... 3
2. Requirements ............................................................................................. 4
3. Terminal Setup ........................................................................................... 5
4. Logon to the Console .................................................................................. 6
5. ConfigureIPAddress .................................................................................. 7
6. Start Web Management ............................................................................... 9
Customer Support ...........................................................................................12
3
1. Package ContentThank you for purchasing PLANET 16-/24-Port Gigabit 802.3at PoE ManagedSwitches,WGSW-20160HP /WGSW-24040HP /WGSW-24040HP4. The descriptionofthesemodelsisasfollows:
WGSW-20160HP:16-Port10/100/1000Base-T802.3atPoE+4-PortGigabitTP/SFPComboManagedSwitch
WGSW-24040HP:24-Port10/100/1000Base-T802.3atPoEwith4SharedSFPManagedSwitch/220W
WGSW-24040HP4:24-Port10/100/1000Base-T802.3atPoEwith4SharedSFPManagedSwitch/440W
“Managed Switch” will also bementioned as an alternative to the above threemodelsinthisQuickInstallationGuide.
Open the box of the Managed Switch and carefully unpack it. The box shouldcontainthefollowingitems:
TheManagedSwitchx1 l
User’s Manual CD x 1 l
QuickInstallationGuidex1 l
RS232 Cable x 1 l
RubberFeetx4 l
TwoRack-MountingBracketswithAttachmentScrewsx1 l
PowerCordx1 l
If any item is found missing or damaged, please contact your local reseller forreplacement.
4
2. RequirementsWorkstationsofsubscribersrunningWindowsXP/2003/Vista/7/8/2008,MACOS9 lorlater,Linux,UNIXorotherplatformscompatiblewithTCP/IPprotocols.
WorkstationinstalledwithEthernetNIC(NetworkInterfaceCard) l
Serial Port Connect l (Terminal)
TheabovePCwithCOMPort(DB9)
Ethernet Port Connect l
Networkcables-Usestandardnetwork(UTP)cableswithRJ-45connectors.
The above PC is installed withWEB Browser and JAVA runtime environmentPlug-in
Note
1.It is recommended to use Internet Explore 7.0 or above toaccesstheManagedSwitch.
2.TheWGSW-20160HPispickedforthis installationguideasthey(the WGSW-24040HP and WGSW-24040HP4) come with thesameconfigurationandPoEfeature.
5
3. Terminal SetupToconfigurethesystem,connectaserialcabletoaCOM port on a PC or notebook computerand to serial (console)port of theManagedSwitch.The consoleport oftheManagedSwitch isDCEalready.So,youcanconnect theconsoleportdirectlytothePCwithouttheneedofNullModem.
PC / Workstationwith
Terminal emulation software
Serial Port
RS-232
Serial Port115200,8,n,1
A terminal program is required tomake the software connection to the ManagedSwitch. Windows’ Hyper Terminal program may be a good choice or pleasedownloadtheotherhyperterminallikesoftware,suchasputty.TheHyperTerminalcanbeaccessedfromtheStart menu.
1. Click START, then Programs, AccessoriesandthenHyper Terminal.
2.When the following screen appears, make sure that the COM port should beconfiguredas:
Baud :115200
Databits :8
Parity :None
Stopbits :1
FlowControl :None
6
4. Logon to the ConsoleOnce the terminal is connected to thedevice,poweron theManagedSwitch.Theterminalwillstartrunningtestingprocedures.
Then, the login username and password are requested. The factory defaultusername and password are as follows, and the login screen in Figures 4-1appears.
Username:adminPassword:admin
Figure 4-1: Managed Switch Console Login Screen
Note
1.Forsecurityreason,pleasechangeandmemorizethenewpass-wordafterthisfirstsetup.
2.Only accept command in lowercase letter under console inter-face.
7
5.ConfigureIPAddressTheManagedSwitchisshippedwithdefaultIPaddressshownbelow:
IPAddress:192.168.0.100SubnetMask:255.255.255.0
TocheckthecurrentIPaddressorcreateanewIPaddress for theSwitch,pleaseusetheproceduresasfollows:
■ Show the current IP Address1. On "WGSW-20160HP:/>” prompt, enter “show ip”.
2.ThescreendisplaysthecurrentIPaddress,SubnetMaskandGatewayasshowninFigure5-1.
Figure 5-1: Display of IP Information
8
■ ConfigureIPAddress3. On “WGSW-20160HP:/>” prompt, enter the following command and press<Enter>asshowninFigure5-2.
"WGSW-20160HP:/IP> setup 192.168.1.100 255.255.255.0 192.168.1.1
ThepreviouscommandwouldapplythefollowingsettingsfortheManagedSwitch.
IP Address: 192.168.1.100Subnet Mask: 255.255.255.0Gateway: 192.168.1.1
Figure 5-2: Setting IP Address
4.RepeatStep1tocheckiftheIPaddressischanged.
If the IP is successfully configured, the Managed Switch will apply the new IPaddresssetting immediately.Youcanaccess theWeb interfaceofManagedSwitchthroughthenewIPaddress.
Note
If you are not familiar with console command or the relatedparameter, enter “help”anytimeinconsoletogetthehelpdescrip-tion.
9
6. Start Web ManagementThe following shows how to start up the Web Management of the ManagedSwitch. Note the Managed Switch is configured through an Ethernet connection.Please make sure the manager PC must be set on the same IP subnet address.
For example, the default IP address of the Managed Switch is 192.168.0.100, thenthemanagerPCshouldbesetat192.168.0.x(wherexisanumberbetween1and254,except100),andthedefaultsubnetmaskis255.255.255.0.
PC / Workstationwith
IE Browser
RJ-45/UTP-Cable
IP Address:192.168.0.x
IP Address:192.168.0.100
Figure 6-1: I P Management Diagram
Login the Managed Switch1.Use Internet Explorer 7.0 or above Web browser. Enter IP address
http://192.168.0.100(thefactorydefaultIPaddressortheonethatyouhavejustchangedinconsole)toaccesstheWebinterface.
2.When the following dialog box appears, please enter the default username andpassword“admin” (or the password youhave changed via console). The loginscreeninFigure6-2appears.
DefaultUsername:adminDefaultPassword:admin
Figure 6-2: Login Screen
10
3.Afterenteringthepassword,themainscreenappearsasFigure6-3shows.
Figure 6-3: W eb Main Screen of Managed Switch
The Switch Menu on the left of theWeb page lets you access all the commandsandstatisticstheManagedSwitchprovides.
Figure 6-4: Switch Menu
Note
Ifyouarenot familiarwithSwitchfunctionsortherelatedparam-eter, press “Help icon” anytime in the Web page to get the help description.
11
Now, you can use the Web management interface to continue the Switchmanagement or manage the Switch by console interface.
Please refer to the user’s manual for more.
■ Changing IP Address or forgetting admin password –To reset the IP address to the default IP Address “192.168.0.100” or reset the login password to default value, press the hardware reset button at the front panel for about 10 seconds. After the device is rebooted, you can login themanagementWEBinterfacewithinthesamesubnetof192.168.0.xx.
[WGSW-20160HP Reset Button Location]
Reset
115200, N, 8, 1
Console
WGSW-20160HP
PWR
SYS
FAN2
FAN1
Reset
2 6 10 14 184 8 12 16 20
1 5 9 13 173 7 11 15 19
ACTLNKPoE In-Use
ACT1000ACT10/100
Alert
[WGSW-24040HP / WGSW-24040HP4 Reset Button Location]
Console
115200, N, 8, 1 PWRReset
18 20 22 242 4 6 8 10 12 14 16
17 19 21 231 3 5 7 9 11 13 15
WGSW-24040HP
PoE
ACTLNK PoE In-Use
Reset
12
Customer SupportThank you for purchasing PLANET products. You can browse our online FAQresource at the PLANET website first to check if it could solve you issue. If youneedmoresupportinformation,pleasecontactPLANETswitchsupportteam.
PLANETonlineFAQ:http://www.planet.com.tw/en/support/faq.php?type=1
Switchsupportteammailaddress:[email protected]
Copyright © PLANET Technology Corp. 2013.Contents are subject to revision without prior notice.PLANET is a registered trademark of PLANET Technology Corp.All other trademarks belong to their respective owners.