4. Rear Fender

8/10/2019 4. Rear Fender

1/9

| P a g e


2/9

2 | P a g e

Rear Fender

Open a new part with model units set to

millimeters.

Go to: File > New > Part

Select the three planes in the feature tree

and make them visible by clicking on the

glasses.

Change the names of the planes

Double click on the Front Plane in the feature tree.

Change the name into: FRONTPLANE REAR FENDER

Double click on the Top Plane in the feature tree.

Change the name into: CENTERPLANE REAR FENDER

Double click on the Right Plane in the feature tree.

Change the name into: MIDPLANE REAR FENDER

Select the FRONTPLANE REAR FENDER andcreate a sketch by clicking on the 2D

sketch icon

Draw the sketch as shown in the picture.

Start with the vertical construction lineand circle.

Offset the vertical construction line

bi-directional by clicking on the offseticon.

Change into: 182 mm

Select the Bi-directional option

Click OK

Draw the sketch as show in the picture

and trim all the lines you dont need

Add all the dimensions and sketch relations


3/9


4/9

4 | P a g e

Select the CENTERPLANE REAR FENDER andcreate a new sketch

Draw a vertical construction line

starting at the origin.

Draw two circles and add the

dimensions as shown in the picture.

Create an extruded cut

Go to: Insert > Cut > Extrude

Direction 1 : Trough All

Ensure that the offset is directed to

above.

If not, click Reverse direction

Click OK


5/9

5 | P a g e

Create a radius on the corners of the fender

Select the four green corners as shown in the picture.

Go to: Insert > Features > Fillet/Round > 45 mm

Click OK

Create a surface fillet

Select the green surface as shown in the picture.

Go to: Insert > Features > Fillet/Round > 4 mm

Click OK


6/9

6 | P a g e

Create a shell on the green surface

Select the green surface as shown in the picture.

Go to: Insert > Features > Shell > 4 mm

Click OK

Create a new plane parallel at the CENTERPLANE REAR FENDER

Go to: Insert > Reference Geometry > Plane

Select the CENTERPLANE REAR FENDER as shown in the picture.

Change the Offset Distance into 400 mm.

Ensure that the offset is directed to above.

If not, click Reverse direction

Click OK


7/9

7 | P a g e

Save the file with the following name: Rear Fender

Insert a projected sketch

Go to: File > Open > Graphic Rear Fender.SLDPRT

(Or use 1 of the 35 tribal graphics)

Right click on Sketch1 in the feature tree and click on the

sketch icon.

Select the sketch and click: Edit > Copy

Go back to File > Open > Rear Fender.SLDPRT

Select Plane 1 and create a new sketch

Draw a vertical construction line starting at the origin

as shown in the picture.

Go to: Edit > Paste

Go to: Tools > Sketch Tools > Move

Select the imported sketch.

Start point : Select the yellow top point of the sketch

as shown in the left picture.

End point: Select the top point of the vertical

construction line as shown

in the right picture.

Click OK


8/9

8 | P a g e

Create an extruded cut

Go to: Insert > Cut > Extrude

Direction 1 : Offset From Surface

Change into 0,10 mm

Select the pink surface as shown in the picture.

Select the Reverse offset option.

Click OK

Change the color of the flames:

Select Extrude3 or the new face > Right click > Feature Properties > Color > Change

color > Select the color you like.

Click OK


9/9

9 | P a g e

Hide all planes and sketches except:

-

FRONTPLANE REAR FENDER

- CENTERPLANE REAR FENDER

- MIDPLANE REAR FENDER

Save the file again.

Congratulations, you just finished the Rear Fender!

Documents

4. Rear Fender