4-Port Antenna Frequency Range 1710–2170 2490–2690 Dual ... · Page 2 of 2 936.4037/a Subject to alteration. Installation of the feederline connector and RCU (optional): In order

Mechanical specifi cations

Input 4 x 7-16 female (long neck)

Connector position Bottom

Adjustment mechanism 2x, Position bottom continuously adjustable

Wind load (at Rated Wind Speed: 150 km/h)

N | lbf Frontal: 255 | 57Maximal: 280 | 63

Max. wind velocity km/hmph

200124

Height / width / depth mminches

1442 / 155 / 8956.8 / 6.1 / 3.5

Category of mounting hardware

M (Medium)

Weight kglb

10 / 12.2 (clamps incl.)22.1 / 26.9 (clamps incl.)

Packing size mminches

1795 x 182 x 13770.1 x 7.2 x 5.4

Scope of Supply Panel and 2 units of clampsfor 42–115 mm |

1.7–4.5 inches diameter

80010644V01 Page 1 of 2

936.4

884/b

S

ub

ject

to a

ltera

tio

n.

4-Port AntennaFrequency RangeDual PolarizationHPBWAdjust. Electr. DTset by hand or by optional RCU (Remote Control Unit)

2490–26901710–2170

XX

60°65°

2°–14°2°–14°

4-Port Antenna 1710–2170/2490–2690 65°/60° 18/18dBi 2°–14°/2°–14°T

Type No. 80010644V01Highbands B1, connector 1–2B1, connector 1–2 Y1, connector 3–4Y1, connector 3–4

1710–2170 2490–2690Frequency range MHz 1710 – 1990 1920 – 2170 2490 – 2690

Polarization ° +45, –45 +45, –45 +45, –45

Gain dBi 17.5 18.0 17.7

Horizontal Pattern:Half-power beam width ° 68 65 61

Front-to-back ratio (180°±30°) dB > 25 > 25 > 25

Cross polar ratio 0°Sector ±60°

dBTypically: 25

> 10Typically: 25

> 10Typically: 25

> 10

Tracking, Avg. dB < 1.5

Vertical Pattern:Half-power beam width ° 6.8 6.1 4.8

Electrical tilt, continuously adjustable ° 2–14 2–14

Sidelobe suppression– for fi rst sidelobe above main beam– within 0°–20° sector above horizon

°TdBdB

2 ... 8 ... 14≥ 18 ... 18 ... 16≥ 17 ... 17 ... 16

2 ... 8 ... 14≥ 18 ... 18 ... 17≥ 17 ... 17 ... 16

2 ... 8 ... 14≥ 18 ... 18 ... 16≥ 17 ... 16 ... 12

Impedance Ω 50 50

VSWR < 1.5 < 1.5

Isolation: Intrasystem dB > 30 > 30

Isolation: Intersystem dB > 30 > 30

Intermodulation IM3 dBc < –150 (2 x 43 dBm carrier) < –150 (2 x 43 dBm carrier)

Max. effective power per portMax. effective power for the antenna

W200 (at 50 °C ambient temperature)600 (at 50 °C ambient temperature)

Y1Y1B1B1

Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]

All specifications are subject to change without notice.The latest specifications are available at www.kathreinusa.com

Any previous data sheet issues have now become invalid.

Page 2 of 2 80010644V01

936.4

884/b

S

ub

ject

to a

ltera

tio

n.

AccessoriesGeneral Information

For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.Wall mounting: No additional mounting kit needed.

Material: Refl ector screen: Aluminum. Radiator: Tin-plated zinc.Flat fi berglass radome: The max. radome depth is only 89 mm | 3.5 inches. Fiber glass material guarantees optimum performance with regards to stability, stiffness, UV resistance and painting. The color of the radome is grey.All screws and nuts: Stainless steel or hot-dip galvanized steel.

Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded.

Bottom view* Dimensions refer to radomeAll dimensions in mm | inches

104 | 4

.1

174 | 6.9

155 | 6.1 *

89 | 3

.5 *2 31 4

1710

–2170 Tilt B

1 Y1Til

t 2490–2690

Adjustment mechanismwith integrated scale

All dimensions in mm | inches

1)

1442 | 5

6.8

1526 | 6

0.1

1496 | 5

8.9

2)1) 9 | 0.42) 64 | 2.5

Layout of interface:

Correlation Table

Frequency range Array Connector

1710–2170 MHz B1 1–2

2490–2690 MHz Y1 3–4

B1

Y1

1x

Accessories (order separately if required)

Type No. Description Remarksmm | inches

Weight approx.kg | lb

Units per antenna

731651 1 clamp Mast diameter: 28 – 60 | 1.1 – 2.4 0.8 | 1.8 2



737978 1 downtilt kit Downtilt angle: 0° – 15° 2.3 | 5.1 1

Accessories (included in the scope of supply)




738546 Page 1 of 1

Mounting HardwareClamp Included in the Scope of Supply

936.

3920

/c

Sub

ject

to a

ltera

tion.

Suitable for mast diameter (mm)[inches]

42 – 115[1.65 – 4.53]

Antenna – mast distance (mm)[inches]

20 – 25[0.79 – 0.98]

Material of clamp and screws Hot-dip galvanized steel / stainless steel

Weight (kg)[lb]

1.1[2.43]

Please note: Kathrein does not recommend to use counter nuts.The additional nuts supplied are only meant as spares.

All dimensions in mm and [inches]

152 [5.98]

100 [3.94]40 [1.57]

72 [2.83]

35 [1.38]

64 [2.52]

125 [4.92]

40 [1

.57]

20–

25

[0.7

9–

0.98

]

42–115

[1.65–4.53]

M10 MA = 25 Nm

M8 MA = 20 Nm

20–25

[0.79–0.98]



Page 1 of 2

936.4

037/a

S

ub

ject

to a

ltera

tio

n.

General Instructionsfor Adjustment Mechanism

Description of the adjustment mechanism (protective cap removed):

Manual adjustment procedure:

Optional: RCU (Remote Control Unit) for remote-controlled downtilt adjustment:

For a description of RCU installation please refer to the respective data sheet.

Remove the protective cap and the

twist protection completely.

➀ Twist protection.

➁ Downtilt spindle with integrated

scale.

➀ Thread for fi xing the pro tective

cap or the RCU (Remote Control

Unit).

➁ Gearwheel for RCU power drive.

To set the downtilt angle exactly,

you must look horizontally at the

scale. The lower edge of the gear-

wheel must be used for alignment.

Set downtilt angle by rotating the

gearwheel.

Screw on the twist protection and

the protective cap again.

0° – max.°

0° – max.°

1

2

2

1



Page 2 of 2

936.4

037/a

S

ub

ject

to a

ltera

tio

n.

Installation of the feederline connector and RCU (optional):In order to protect the adjustment mechanism, the protective caps have to be attached during feederline installation!

Carefully place the connector and

fi x the nut using a torque-wrench

(according to the manufacturers

guidelines).

After feederline installation, the

optional remote control units

(RCUs) can be mounted.

These tools are suitable for 7-16 connectors with a wrench size of

27 or 32 mm | 1.1 or 1.3 inches, and the RCU attachment nut with a

wrench size of 41 mm | 1.6 inches.

Tighten nuts within a torque range of 25 – 33 Nm depending on

connector manufacturers’ specifi cations, respectively the RCU nut

with a torque range of 15 – 18 Nm.

Kathrein installation set: Type No. 85010077Set has to be ordered separately!Set consists of three spanners of divers width27, 32 and 41 mm | 1.1, 1.3 and 1.6 inches

32 | 1.3

41 | 1

.627 | 1

.1

1/2˝ square actuationaccording toDIN 3120 Form C

All dimensions in mm | inches

Colour coding:Correlation of each RF input to:– the corresponding adjustment mechanism– the frequency range– the polarization

Ventilation hole

Spindle with tilting scale

7-16 female (long neck)

Adjustment mechanism(protective cap removed)

General Instructions for Feederline and RCU Installation for Antennas

Please note: In order not to damage the interfaces, please make sure that only the right tools are used.

Tighten the feederline connector interfaces solely by using a common torque-wrench with a suitable wrench

width.

Description of bottom end cap (exemplary picture):



Documents

4-Port Antenna Frequency Range 1710–2170 2490–2690 Dual ... · Page 2 of 2 936.4037/a Subject to alteration. Installation of the feederline connector and RCU (optional): In order