3D simulations of wind-jet interaction in massive X-ray

binaries

M. Perucho,V. Bosch-Ramon,and D. Khangulyan

A&A February 24,2010arXiv:1002.4562v1

Introduction• High-mass microquasars(HMMQ) jets, s

tellar winds, binary system spatial scales

• Collisionless shocks in MQ jets, efficient particle acceleration, non-thermal emission of synchrotron and inverse Compton origin, proton-proton collisions.

• Dynamics of these jets, numerical simulations of their propagation

• Perucho&Bosch-Ramon(2008)-PRB08 strong wind of an OB star, orbital separation(~0.2 AU).

• Simulations in two dimensions hydrodynamical jet, homogeneous stellar wind, cylindrical and slab symmetries.

• Recollimation shock ~1012cm, efficient particle acceleration and gamma-ray emission, HMXB

• Jet disruption, kinetic luminosities Lj~1036erg s-1 , ~0.1-1% of the Ledd

• 3D simulations: hydrodynamical jets , typical OB star wind.

• 1036 erg s-1 may be disrupted, lower wind-jet momentum transfer due to wind sidewards escape , enhanced development of disruptive instabilities.

• The simulations also show a strong recollimation shock that could efficiently accelerate particles.

Simulations

• Lj=1035(Jet 1) and 1037 erg s-1(Jet 2).

• An isotropic wind(as seen from the star), mass-loss rate of 10-6 M ⊙yr-1, constant velocity of 2×108 cm s-1(PBR08).

• Rorb=2×1012 cm

• Injected at a distance to the compact object of z0=6×1010 cm , initial jet radius Rj=6×109 cm.

• Ρ0=0.55c(1.7×1010 cm s-1), T=1010 K , M=17

• ρ1=0.088ρw and ρ2=8.8ρw, Pj,1=71 erg cm-3 and Pj,2=7.1×103 erg cm-3, ρw =3×10-15 g cm-3 is the wind density at z0.

• z for the direction of the initial propagation of the jet, x for the direction connecting the jet base and the star, and y for the direction perpendicular to z and x.

• Magnetic field has no dynamical influence , wind is continuous and homogeneous , simulation time, ~103 s, much smaller than the orbital period.

• The numerical grid box expands transversely 20 Rj on each side of the axis, 320 Rj along the axis.

• The numerical resolution of the simulation is of four cells per initial jet radius.

• At the z of interest(~1012 cm) in the main grid is ~16 cells per Rj.

Results

• Jet 1 propagates up to z ≤1.6×1012 cm after≈1250 s.

• Propagates very slowly from zs≈2×1011

cm to 4×1011 cm, as the pressure in the cocoon drops.

• This process ends up in the mixing and deceleration of the jet flow at z≥1012 cm.

• At the end of the simulation, the velocity of the bow shock at jet head is ≈3×108 cm s-1.

• vbs t∝ -0.6.

• will not propagate out of the binary system as a supersonic and collimated flow.

Fig.2. Transversal cuts for the axial velocity, Mach number and tracer in Jet 1 at z≈1.3×1012 cm. The Mach number is saturated for values higher than 20 (the wind).

• fmax<1• The maximum velocity in the jet flu

id is still relatively fast (≈1.5×1010 cm s-1) despite the irregular morphology and mixing, but the average Mach number is close to one.

Fig.3. Same plots as in Fig. 1,for Jet 2.

The jet expands more at the base because it is initially denser (more overpressured), the velocity of the jet head, the reconfinement shock is stronger and occurs at larger z.

• location of the shock , z≈6×1011 cm to 1012 cm

• the structure of the bow shock at z≈1.3×1012 cm is observed to be more symmetric than in Jet 1.

Fig. 4. Same as in Fig. 2 for Jet 2 at z≈1.5×1012 cm. The Mach number is saturated for values higher than 20 (the wind).

• (f=1) and that the flow velocity is still as high as that in the injection point.

• At the end of the simulation,the velocity of the bow shock is ≈ 8.4×109 cm s-1,which is close to its initial speed (≈9×109 cm s-1).

• Lj=1037 erg s-1 seems to be close to the minimum jet power to propagate out of the binary region without disruption.

Discussion• it is worthwhile to extimate here analyticall

y whether the shock remains inside the binary region when the jet head is already outside. This will depend on whether the wind ram pressure can substitute the cocoon pressure to keep the recollimation shock inside the system.

• We know that:

This result can be tested using our simulation,in which the ambient medium

is still roughly homogeneous( at z ≤Rorb).• For Jet 2 the recollimation shock forms at z=6×1011 cm at t1≈61 s. At t2≈21

0 s,taking into account that the velocity is basically constant(α=0),zs(t2)/zs(t

1)=(t2/t1)1/2,which results in zs(t2)=1.1×1012 cm,in agreement with the simulation.

• We can then extrapolate to find out the time (t3) at which the shock would reach z=2×1012 cm. Taking t2=210 s, and zs(t2)=1.1×1012 cm we obtain for :t3 ≈ 2t2 ≈400 s.

tzzt

P

tzt

vt

P

Pz

sac

sbsc

c

s

22

2/12/1

1,

1

1,

1

1

2

1

za

• Pw~102 erg cm-3 at t2=210 s, pressure equilibrium with the shocked wind will be reached at

• This means that Jet 2 is around the limit to keep the r

ecollimation shock inside the system by the wind ram pressure alone, under the simulated conditions.

• For hotter or denser jets, the recollimation shock can move out of the region of interest at a finite time, whereas for colder or lighter jets, this shock will stay inside the binary system. This allows for continuous production of energetic emission, but puts the jet in danger of disruption.

.3/ 220, ttPPt wc

Thank you!