(3 SECTIONS WITH 2 EXTENSION CORDS) PLEASE READ ...€¦ · o this product employs electrical overload protection (fuses) inside each plug. spare fuses are provided in the carton

7.5ft BAKERSVILLE SPRUCE TREE

(61341)

ASSEMBLY INSTRUCTIONS (3 SECTIONS WITH 2 EXTENSION CORDS)

PLEASE READ INSTRUCTIONS BEFORE ASSEMBLYING YOUR TREE Your 7.5’ Bakersville Spruce Tree should contain the following: 1 Tree stand Replacement bulbs and fuses If any piece is missing please contact a Grandinroad 2 Eyelet screws 3 Tree sections labeled A, B, C Product Specialist

HOW TO ASSEMBLE AND SHAPE YOUR TREE:

1. BEFORE STARTING TO ASSEMBLE YOUR TREE, CHOOSE A LOCATION NEAR AN 110V ELECTRICAL WALL OUTLET FOR THE PRELIT TREE.

2. REMOVE THE TREE SECTIONS FROM THE CARTON. SECTION A IS THE BOTTOM, SECTION B IS THE MIDDLE AND SECTION C IS THE TOP OF THE TREE.

3. PLACE THE TREE STAND ON A LEVEL SURFACE. INSTALL THE BOTTOM END OF THE LOWER “SECTION A” INTO THE STAND. HOLD THE SECTION IN A LEVEL POSITION AND TIGHTEN THE EYELET SCREWS IN THE STAND AGAINST THE TREE TRUNK SURFACE. MAKE SURE THE SCREWS ARE TIGHTENED AS EVENLY AS POSSIBLE MAINTAINING A SNUG AND SECURE POSITION. (FIG 1~2)

FIGURE 1 FIGURE 2

4. INSERT THE MIDDLE (“SECTION B”) INTO THE BOTTOM (“SECTION A”) TREE POLE. FINISH BY INSERTING THE TOP (“SECTION C”) INTO THE MIDDLE (“SECTION B”) TREE POLE. (FIG 3~4)

FIGURE 3 FIGURE 4 5. LOCATE THE PLUG FROM SECTION C AND PLUG INTO THE RECEPTACLE HUB

LOCATED IN SECTION A. THE HUB WILL HAVE A YELLOW CARD ATTACHED FOR EASY

IDENTIFICATION. ***DO NOT REMOVE THE ELECTRICAL TAPE FROM THE HUB***

(SECTION C PLUG) 6. SHAPE THE BRANCHES, STARTING AT THE BOTTOM WITH THE TIPS FARTHEST FROM

THE POLE AND CURVING OUT FROM THE POLE. ONE TO THE RIGHT, ONE TO THE LEFT AND ONE AT THE CENTER. TO ACHIEVE A REALISTIC LOOK, EACH BRANCH SHOULD BE SHAPED.

8. SHIFT ANY BRANCHES AS NECESSARY TO FILL ANY GAPS AND SLIGHTLY UPSWEEP ALL BRANCHES FOR A UNIFORM LOOK.

9. PLUG THE TWO REMAINING EXTENTSION CORDS CORD INTO A GROUNDED ELECTRICAL OUTLET OR POWER STRIP.

(SECTION A EXTENSION CORD) (SECTION B EXTENSION CORD)

BULBS AND FUSES: Fuses: The fuses are designed to prevent a short circuit or overheating that could lead to damage to the lights. The most common cause for a blown fuse is a power surge.

Each cord string of Christmas tree lights has a fuse housed in the plug. When a fuse blows, the lights will simply stop working. Whenever an entire strand (or in some cases the entire tree) ceases to light, check the fuses before you try tightening or replacing the light bulbs.

To Replace a Fuse:

1. Unplug the Christmas lights. *****Make sure the light string is unplugged from the wall and any other light strings before you start working on it. 2. Slid open the fuse box on your Christmas tree light string to confirm that

the fuse is blown. You can see the fuse box clearly marked on the light string plug. Slide the top of the fuse box off with pressure from your thumb. If you cannot move it with your thumb, use a flat-head screwdriver to gently push the door open.

3. Examine the fuse to see if it is blown. A blown fuse will have a black

residue evident inside the glass chamber. If there is no black residue, the blown fuse is in a different string.

4. Pop out the fuse by gently placing a small flat-head screwdriver under the fuse and apply gentle pressure upwards.

5. Place the new fuse over the area where it will be installed. Press down gently over top of both contact areas with two fingers until the fuse pops into place. *****Do not apply pressure to the glass part of the fuse when removing it or putting the new one in. Apply all pressure to the metal contacts. Complete by sliding close the fuse door.

To Replace Bulbs:

1. Unplug the Christmas lights. *****Make sure the light string is unplugged from the wall and any other light strings before you start working on it.

2. Remove each of the blown-out Christmas light bulbs. Use your thumb and index finger to delicately put pressure on each of the broken light's plastic jacket, to remove the bulb(s) from the bulb base.

(Bulb Base) 3. Make sure the two copper wires are completely aligned with the bulb's

base and the copper contact points inside the base. Now, insert the replacement bulb into the old bulb's socket.

7.5ft BAKERSVILLE SPRUCE TREE:

STORAGE

GENTLY PRESS BRANCHES AGAINST THE TREE TRUNK AS YOU DISMANTLE THE TREE

REMOVE THE TREE STAND FROM SECTION A

CAREFULLY PLACE THE TREE SECTIONS AND TREE STAND BACK INTO THE CARTON(S) AND TAPE THEM CLOSED CAUTIONS AND WARNINGS

o DO NOT LIFT SECTIONS OF THE TREE WITH THE BRANCHES. LIFT USING THE METAL POLE.

o DO NOT STEP ON THE BRANCHES DURING THE ASSEMBLY PROCESS

o DO NOT TWIST THE BULBS WHEN REPLACING AND ONLY USE THE SPARE BULBS PROVIDED IN THE CARTON AS REPLACEMENTS. PULL THE LAMP AND PLASTIC BASE STRAIGHT OUT OF THE LAMPHOLDER.

o DO GRASP ELECTRICAL PLUGS AND REMOVE IT FROM THE RECEPTACLE OR OUTLET DEVICE. NEVER UNPLUG BY PULLING ON THE CORD.

o PLEASE DO NOT REMOVE TAPE FROM PLUG HUBS; THIS IS FOR YOUR PROTECTION AND TO INSURE THAT THE PLUGS MAINTAIN A FIRM CONNECTION.

o DO NOT HANG ORNAMENTS OR OTHER OBJECTS FROM THE ELECTRICAL CORDS OR WIRES.

o THIS PRODUCT EMPLOYS ELECTRICAL OVERLOAD PROTECTION (FUSES) INSIDE EACH PLUG. SPARE FUSES ARE PROVIDED IN THE CARTON. OUR PRODUCT DESIGN HAS NOT EXPERIENCED FUSE PROBLEMS; HOWEVER, IF A FUSE BLOWS THE PRODUCT SHOULD BE UNPLUGGED BEFORE REPLACING ANY FUSE.

o WHEN A LIGHT SET FLICKERS OR GOES ON AND OFF, THE MOST COMMON PROBLEM IS A LOOSE FITTING BULB. CHECK TO MAKE SURE ALL BULBS ARE SEATED FIRMLY IN THE SOCKETS.

o THE MOST COMMON PROBLEM WITH A LIGHT SET IS A BULB THAT NEEDS REPLACING. LOOSE OR DAMAGED BULBS CAN CAUSE AN ENTIRE STRING TO FAIL. A BURNED OUT BULB WILL NOT CAUSE THE STRING TO GO OUT IF IT IS NOT REMOVED.

CARE AND MAINTENANCE STORE CARTON IN COOL AND DRY PLACE. DO NOT STORE THE TREE IN A DAMP AREA OR IN AN AREA WHERE THE TEMPERATURE EXCEEDS 100˚ F.

9ft BAKERSVILLE SPRUCE TREE

(61342)


PLEASE READ INSTRUCTIONS BEFORE ASSEMBLYING YOUR TREE Your 9’ Bakersville Spruce Tree should contain the following: 1 Tree stand Replacement bulbs and fuses If any piece is missing please contact a Grandinroad 3 Eyelet screws 4 Tree sections labeled A, B, C, D Product Specialist



2. REMOVE THE TREE SECTIONS FROM THE CARTON. SECTION A IS THE BOTTOM, SECTION B IS THE LOWER MIDDLE, SECTION C IS THE UPPER MIDDLE AND SECTION D IS THE TOP OF THE TREE.

3. PLACE THE TREE STAND ON A LEVEL SURFACE. INSTALL THE BOTTOM END OF THE LOWER “SECTION A” INTO THE STAND. HOLD THE SECTION IN A LEVEL POSITION AND TIGHTEN THE EYLET SCREWS IN THE STAND AGAINST THE TREE TRUNK SURFACE. MAKE SURE THE SCREW ARE TIGHTENED AS EVENLY AS POSSIBLE MAINTAINING A SNUG AND SECURE POSITION. (FIG 1~2)

FIGURE 1 FIGURE 2

4. INSERT THE LOWER MIDDLE (“SECTION B”) INTO THE BOTTOM (“SECTION A”) TREE POLE. FOLLOW BY INSERTING UPPER MIDDLE (“SECTION C”) INTO THE LOWER MIDDLE (“SECTION B”). FINISH BY INSERTING THE TOP (“SECTION D”) INTO THE MIDDLE (“SECTION C”) TREE POLE. (FIG 3~5)

FIGURE 3 FIGURE 4 FIGURE 5 5. LOCATE THE PLUG FROM SECTION D AND PLUG INTO THE RECEPTACLE HUB

LOCATED IN SECTION A. THE HUB WILL HAVE A YELLOW CARD ATTACHED FOR EASY

IDENTIFICATION. ***DO NOT REMOVE THE ELECTRICAL TAPE FROM THE HUB***

(SECTION D PLUG) 6. SHAPE THE BRANCHES, STARTING AT THE BOTTOM WITH THE TIPS FARTHEST FROM



8. PLUG THE THREE REMAINING EXTENTSION CORDS CORD INTO A GROUNDED POWER STRIP.

(SECTION A EXT. CORD) (SECTION B EXT. CORD) (SECTION C EXT. CORD)

9ft BAKERSVILLE SPRUCE TREE:

STORAGE














10ft BAKERSVILLE SPRUCE TREE

(61343)


PLEASE READ INSTRUCTIONS BEFORE ASSEMBLYING YOUR TREE Your 10’ Bakersville Spruce Tree should contain the following: 1 Tree stand Replacement bulbs and fuses If any piece is missing please contact a Grandinroad 3 Eyelet screws 4 Tree sections labeled A, B, C, D Product Specialist



2. REMOVE THE FOUR TREE SECTIONS FROM BOTH CARTONS. SECTION A IS THE BOTTOM, SECTION B IS THE LOWER MIDDLE, SECTION C IS THE UPPER MIDDLE AND SECTION D IS THE TOP OF THE TREE.

3. PLACE THE TREE STAND ON A LEVEL SURFACE. INSTALL THE BOTTOM END OF “SECTION A” INTO THE STAND. HOLD THE SECTION IN A LEVEL POSITION AND TIGHTEN THE EYLET SCREWS IN THE STAND AGAINST THE TREE TRUNK SURFACE. MAKE SURE THE SCREW ARE TIGHTENED AS EVENLY AS POSSIBLE MAINTAINING A SNUG AND SECURE POSITION. (FIG 1~2)

FIGURE 1 FIGURE 2

4. INSERT THE LOWER MIDDLE (“SECTION B”) INTO THE BOTTOM (“SECTION A”) TREE POLE. FOLLOW BY INSERTING THE MIDDLE (“SECTION C”) INTO THE LOWER MIDDLE (“SECTION B”). FINISH BY INSERTING THE TOP (“SECTION D”) INTO THE MIDDLE (“SECTION C”) TREE POLE. (AS ILLUSTRATED BELOW)

5. LOCATE THE DOUBLE PIGGY-BACKED PLUG FROM SECTION D AND PLUG INTO THE

RECEPTACLE HUB LOCATED IN SECTION B. THE HUB WILL HAVE A YELLOW CARD

ATTACHED FOR EASY IDENTIFICATION. ***DO NOT REMOVE THE ELECTRICAL TAPE FROM THE HUB***

(SECTION E PLUG) 6. SHAPE THE BRANCHES, STARTING AT THE BOTTOM WITH THE TIPS FARTHEST FROM



8. PLUG THE THREE REMAINING EXTENTSION CORDS CORD INTO A GROUNDED POWER STRIP.

(SECTION A EXT. CORD) (SECTION B EXT. CORD) (SECTION C EXT. CORD)

10ft BAKERSVILEE SPRUCE TREE

STORAGE














Documents

(3 SECTIONS WITH 2 EXTENSION CORDS) PLEASE READ ...€¦ · o this product employs electrical overload protection (fuses) inside each plug. spare fuses are provided in the carton