Standard Operation ProcedureInfrastructure Management National

Education Network

Wireline VPN IP

National Education Network tools configuration Wireline VPN IP

• Terestrial/Wireline– Telephone Cable– Modem – Router– UPS

Modem VPN IP

• G.SHDSL– ZyXEL

• TDM– Tellabs– Alcatel

Information:

The selection of the type of modem that is installed in the location specified by the TELKOM.

Notification

• Modem configured by TELKOM.

• For handling the problem,you must watch:– Power supply– Modem indicator led– Cable connection

• contact to Telkom call center (0 800 1 835566)

Type of Modem ZyXEL

LED DESCRIPTIONPWR The Power is ConnectedSYS Blink while performing system testing & then stays on if the testing is successfulLAN Connected to Computer or LANCON/AUX For management by consoleDSL The modem is connected to the IPDSLAM via copper wirePPP/ACT Indicates traffic through modem

Type of Alcatel 2801

LED DESCRIPTIONPower Power is connectedLine Sync The LED in on when the line is active. The LED is off when the line is

inactive. The LED blinks at a rate of one blink per second when the line is in training mode

TXD (data) The LED Blink when data transmittedRXD (data) The LED Blink when data receivedDTR (data) The LED ON when customer equipment (computer, etc) are

connectedRTS/C (data) The LED On when modem ready to send data from customer sideDSR (data) Data Set Ready ON indicates modem ready to accept dataDCD/1 (data) The LED On when modem detects signal from Telcos siteCTS (data) The LED on (Clear to Send) indicates modem in other site ready to

accept signal/data

V35 TEST LINE POWER

Type Of Modem Tellabs CTU-512

LED DESCRIPTIONLine 1 (green) The LED in on when the line is active. The LED is off when the line is

inactive. The LED blinks at a rate of one blink per second when the line is in training mode

Line 2 (green) The LED in on when the line is active. The LED is off when the line is inactive. The LED blinks at a rate of one blink per second when the line is in training mode. The LED is not available in CTU-512

PMA (red) Prompt maintenance alarm. When the LED is on, there is an active major fault in unit. A PMA is generated in order to initiate maintenance activities by maintenance personal

DMA ( yellow) Defered maintenance alarm. When the LED is on, there is an active minor fault or warning in the unit. A DMA is generated when immediate action is not required by maintenance personal

POWER (green) Power on indicator

DataNetwork POWER

Type of Tellabs STU modem

104 105 ENTER103 106 109 EXIT POWERERR142 RALA

DISPLAY

Symbol Color Function103 green Transmitted data. 104 green Receive data105 green Reques to send106 green Ready for Sending109 green Signal detector142 yellow Lit when a test is activeERR red Lit or blinking when the NTU is receiving errors during a testLA red Lokal alarm, Lit when the NTU detects an internal faultRA yellow Remote alarmPOWER green Power ON indicator

V.35220-240/AC

Line

Variant of Modem Tellabs STU

Router VPN IP

Spec:8 Mbps full throughput 2 fixed FE LAN + 1 WAN + 1 expansion slot for backup interfaces

Router Installation Guide

1. Make sure the label according to your location.

2. To install do the following in accordance with procedures :– Location of the Router in the space provided. For installation on a

table, buffer rubber plug on the bottom of the router.

– Plug the power cable and connect the device to a power source (UPS) according to the following picture :

Kabel Power

Router Installation Guide3. Labels printed on the interface used (eth or serial).

– If the modem interface used RJ-45, connect the cable to the router interface fe-0/0/1.

– If Modem V.35 interface is used, plug the cable from the modem to V.35 with serial interface Router se-0/0/2.

Tombol Power

Connection Test Procedures• Prepare your PC / Laptop to test the connection.

• Connect the UTP cable into the Ethernet port Router.

• Configure the IP address of your PC / Laptop with specs:– See label sticker LAN IP address info on Top

Router(118.x.x.x/29).– Fill in the IP Address 118.xx82 if written on a label on the router

118.xx81/29)Subnet Mask = 255.255.255.248– Fill Default Gateway = 118.x.x.81

example of Configuration Settings PC / Laptop on Windows OS

Testing Connection In Windows OS

• Make testing “ping” and “traceroute”, with:– Open the application command. Click Start> Run and type cmd.– Type the command ping 118.98.132.4 and press the enter key.

See the display output obtained Reply Form … Then test the connection is successful.

– Type the command tracert 118.98.132.4 and wait for it to finish.– Capture output by pressing Alt + PrtScr, open MS Word and

do the Paste command. Print these results as evidence ready for operation.

• Make connections to browsing :– Open Internet Explorer and type application http://118.98.132.4

address or http://testing.jardiknas.org– If the materialized view, capture and print the results to be

attached to the Minutes Ready Operation.

Have Problem?

Contact Call Center soon

0800 1 835566

More Information…

www.JARDIKNAS.DIKNAS.Go.Id