266763-000-SP-4006_Capacitor Bank

7/29/2019 266763-000-SP-4006_Capacitor Bank

1/21

LPG BOTTLING PLANT , BATHINDA

Doc. No. 266763-000-SP-4006 Rev: A Page 1 of 21

P:\Kolkata\Engineering\JOBS\OGO-269323-HPCL Bathinda-LPG\ELECTRICAL\03. Issued to client\CapacitorBank\266763-000-SP-4006.doc

Specification for 415 V CapacitorBanks.

Hindustan Petroleum Corporation Ltd

8 S.V. Marg, Ballard Estate

Mumbai- 400 001

Mott MacDonald Consultants (India) Pvt. Ltd.

Kothari House, CTS No. 185

Off Andheri - Kurla Road

Andheri (East)

Mumbai 400 059


2/21


3/21




List of Content Page No

1 Introduction 5

2 Location and Environmental Conditions 62.1 Plant Location 6

2.2 Environmental Conditions 6

2.3 Electrical System Data 6

3 Scope of Supply 6

3.1 Electrical Equipment & Material: 6

3.2 Engineering Services 7

3.3 Exclusions 7

4 Codes and Standards 7

4.1 General 7

4.2 Conflicting Requirements 7

5 Technical Particulars: 8

5.1 Design Criteria: 8

5.2 Construction: 8

5.3 RATINGS & CONTROLS 9

5.4 Tropical Protection 9

5.5 Painting 95.6 Quality assurance: 10

6 Inspection and testing: 10

7 Vendor documentation: 11

8 Spares and special tools: 12

8.1 Spares 12

8.2 Special tools 12

9 Installation and commissioning: 12

10 Packing and transportation: 12

11 Statutory Approval: 13

12 Guarantee: 13

Appendix-A: Table of Compliance. 14

Appendix-B: Electrical System Data 16

Appendix-C: Codes & Standards. 17

Appendix-D: Requisition for Engineering Documents 18


4/21




Appendix-E: Guaranteed Technical Particulars 20

Appendix-F: Electrical Drawings. 21


5/21




1 Introduction

This specification is intended to cover the design, manufacture, assembly, testing at manufacturer's works,

supply & delivery, properly packed for transport F.O.R. site of 415V, 300 kVAR Capacitor Bank along with

APFC relay & with all accessories for efficient and trouble-free operation for the LPG Bottling Plant project

at Bathinda of Hindustan Petroleum Corporation Limited, India. The Capacitor bank will be housed in the

PMCC panel. Hence the capacitor bank forms the part of the PMCC Package Supplier scope of work.

The scope of work shall also include, the supervision of erection, testing, commissioning and putting into

successful commercial operation of the switchgear furnished under this specification

Following are the definitions:

Company/Client/Owner Shall mean Hindustan Petroleum Corporation Limited

(HPCL),

Consultant Shall mean Mott MacDonald Consultants India Pvt. Ltd.

(MMCI).

Manufacturer / Vendor Supplier of 415V PMCC, Capacitor Bank etc.

Shall This is to be understood as mandatory in relation to the

requirements of this document.

Should This is to be understood as a strong recommendation to

comply with the requirements of this document.

Equipment This is to be understood as vendor supplied equipment

with all accessories.

The Vendor shall ensure that the design complies with the requirements of this specification and its

referenced specifications, data sheets & standards. The Guaranteed Technical Particulars, Appendix E,

which forms part of this specification, shall be completed by the Vendor. Deviation if any should be

specifically brought out at the offer stage in the Table of Compliance, Appendix A . Without the compliance

table and Guaranteed Technical Particulars can cause rejection of the offer. Failure to clearly identify

specific deviations if any shall be assumed by the Purchaser to be total compliance with the specification.

This specification does not relieve the Vendor from final guarantee as to materials, apparatus,

workmanship and performance of the equipment supplied.


6/21




2 Location and Environmental Conditions

2.1 Plant Location

The Plant is situated at Village Phulo Khari, Taluka Talwandi Sabo, District Bathinda Punjab. Capacitorbank listed in scope of supply shall be located inside the PMCC panel which is situated in the MCC Room

within plant complex.

2.2 Environmental Conditions

Design ambient temperature for Electrical Equipment (Indoor): 500

C

Design ambient temperature for Electrical Equipment (Outdoor): 550

C

For other details Refer EIA Report for Site Enviormental condition.

2.3 Electrical System Data

Refer Doc No.: 266763-000-SP-4004BX [in Appendix B] for details.

3 Scope of Supply

The following equipments shall be supplied, in accordance with this specification; standards stated herein

& enclosed appendices.

3.1 Electrical Equipment & Material:

Sr. No. Item Description Unit Quantity Remarks

415V Capacitor Bank as per following details:

1.0415V, 300 kVAR capacitors bank along with its

control panels, used for power factor improvement

in 415V Main PMCC as per following details &

attached Single Line diagram Dwg. No 266763-

000-410-002D.

Rated voltage 415 V

Highest system voltage 433 V

Capacitor Bank rating 300 kVA

Short time withstands current 50 kA for 1 Sec.

Control supply Voltage Refer Appendix B

Set 1

Capacitor Bank

along with its

control panel &

APFC relay will

be housed in the

PMCC panel.

Inspection and Testing as specified.

Submission of documents as specified.

Painting as specified.


7/21




Preservation, preparation of shipment and delivery to site.

List of Spares for two years normal operation.

Start-up spares and commissioning spares.

List of special tools required (Vendor to provide list with the bid).

Any other items, required to make system complete.

3.2 Engineering Services

The Vendor shall provide engineering services, which shall include, but not necessarily be limited to, the

following:

Providing/coordinating detailed design of all equipment and components within the scope of

supply.

Resolving engineering queries related to the equipment and components within the scope of

supply.

Performing all relevant calculations pertaining to the equipment and components within the scope

of supply.

Providing progress reports etc.

Providing expediting services for all sub-vendors, if any.

Providing quality assurance, including all sub-vendors if any with respect to ISO 9000 or

equivalent.

Quality Assurance.

Supervision of Installation/erection and commissioning.

Training of clients personnel at site / Vendors shop.

3.3 Exclusions

Installation/Erection & commissioning.

4 Codes and Standards

4.1 General

The Capacitor bank shall meet the requirements of this specification and latest edition of applicable

standards listed in enclosed Appendix-C

4.2 Conflicting Requirements

In case of conflict between documents relating to the enquiry or purchase order, the following priority of

documents shall apply.


8/21




First priority : This engineering specification along with attached drawings/ data sheets

and subsequent purchase order & variations thereto.

Second priority : Relevant Indian /International standards.

Note: Should any conflict arise either before or after order placement the Vendor shall immediately

inform the Purchaser for technical resolution of the conflict.

5 Technical Particulars:

5.1 Design Criteria:

5.1.1 The capacitors shall be connected to the bus of the PMCC and shall be manually as well as

automatically switched in and out in steps so as to correct the power factor to the required value

depending on the actual kVAR requirement of the bus. Compensation to the lagging kVAR shall be

made corresponding to the reference power factor as set on the APFC relay at the panel. The

Tenderer shall supply the necessary L.T. capacitors and the associated control devices complete

with contactors, relays, switches, lamps etc. to achieve the above objective.

5.1.2 Capacitors shall comply with the general safety regulations for power installation prescribed in the

relevant standard.

5.1.3 Capacitors units shall be suitable for operation at a r.m.s. voltage between terminals not exceeding

1.1 times the rated voltage, excluding transients

5.1.4 All capacitors shall be suitably protected against over current by means of suitable over current

trips (other than fuses), which are adjusted to interrupt the circuit when the current exceeds the

safe permissible limit. Capacitor units shall also be protected against the internal faults and the

affected units / banks shall be automatically and immediately isolated in the event of such faults.

5.1.5 Capacitors shall be provided with proper discharge device built into the unit to reduce the residual

voltage to a safe value within the specified time as recommended in the relevant standard after the

capacitor has been disconnected from the supply.

5.2 Construction:

5.2.1 Capacitors units shall be hermetically sealed to protect leaks and contamination of dielectric. All

joining in the steel casing shall be welded and tested for liquid tightness.

5.2.2 Terminals of capacitor units shall be suitably brought out through bushings, hermetically soldered

to the steel case, for external cable connection. Terminals shall be provided with stud, bolts, nuts,

washers and cable shoes of appropriate size for proper termination.

5.2.3 Capacitors shall be of two-layer dielectric design. Impregnated paper or equivalent shall be used

as dielectric material.

5.2.4 Metal container of the capacitors shall be provided with two distinct earthing terminals with nuts,

bolts, washers suitable for connecting 50 mm x 6 mm G.S. strip as earth continuity conductor.


9/21




5.2.5 The capacitors and their control elements like relays, contactors, timers, protective elements shall

be housed in well-ventilated panels. Capacitors and their control elements may be installed in

different compartments of the same panel to minimize the space requirement.

5.2.6 Both manual by ON-OFF push buttons and automatic by Automatic Power Factor Correction relay

shall be provided for power factor correction. Auto/Manual selector switch for the above shall be

provided on the capacitor control panel

5.2.8 The terminals of each capacitor shall be made accessible.

5.3 RATINGS & CONTROLS

The following manual controls shall be provided on the front of the panel:

5.3.1 The selected basic unit size shall be 25kVAr or any lower rating. - to be established by the

Tenderer/ successful Tenderer by design calculation. The built-up unit sizes shall be multiplicationof the single unit i.e. 25kVAr, 50kVAr and 100kVAr. The total capacitor bank shall comprise a

number of the built-up units of different ratings.

5.3.2 The automatic power factor relay shall provide output signals in at least eight (8) stages to enable

achieve the set power factor at all possible loading conditions.

5.3.3 The control panel shall have digital display of the set and achieved power factors and analog

display of current in all the three phases of the line to the capacitor bank.

5.3.4 Rated capacity of the Power factor capacitor improvement panel shall be 300 kVAR. The panel

shall be provided with but not limited to following:

a) 630A ACB with motor operated spring charge operating mechanism and electrically operated

closing and tripping coil, 415/110 V PTs with set of MCCBs, set of CTs, Ammeter with Ammeter

switch, indicating lamps.

b) Capacitors bank will be connected directly with 415V, 1600A, 3 Ph, 4 W bus bars of PMCC.

c) Required number of capacitor duty contactors with backup fuses to feed capacitor banks of

various ratings such as 100 kVAr (4x25 kVAr), 50 kVAr (2x25 kVAr) and 25 kVAr (1x25 kVAr).

5.4 Tropical Protection5.4.1 All equipment, accessories and wiring shall have fungus protection, involving special treatment of

insulation and metal against fungus, insects & corrosion.

5.4.2 Screens of corrosion resistant material shall be furnished on all ventilating louvers to prevent the

entrance of insects.

5.5 Painting

5.5.1 All metal surfaces shall be thoroughly cleaned and degreased, pickled and phosphatised.

Thereafter, a coat of phosphate paint and a coat of zinc chromate primer shall be applied. After

removing all imperfections, all metal surfaces shall be sprayed with two coats of final paint as per

colour shade RAL 7032. Final coat shall be of epoxy based. All unpainted parts shall be plated to

prevent corrosion.


10/21


Doc. No. 266763-000-SP-4006 Rev: APage 10 of

21


5.6 Quality assurance:

5.6.1 The Manufacturer is expected to demonstrate that he has working Quality Assurance System

which complies with ISO 9001 or may be appropriate to the type of contract and his product.

5.6.2 If the Vendor elects to sub-contract part of the work he shall ensure that only those sub-contractorsor suppliers are used who can demonstrate that they operate Quality Systems based on ISO 9001

or ISO 9002 as applicable. The Vendor shall give his sub-contractors or suppliers assistance in

attaining the required standard, if necessary. This shall not relieve the Vendor of his responsibility

for the quality of the finished work. The Owner reserves the right to audit the Vendors Quality

System.

5.6.3 The Vendor shall assign sufficient full time personnel to the Project to ensure the Quality

Assurance / Quality Control System, documented in a Quality Assurance / Control Manual, is

maintained and kept up-to-date throughout the duration of any purchase order. The Vendors

Quality Assurance / Control System shall become an integral part of any Purchase Order. Vendor

shall organize a prefabrication / inspection meeting with the Owner.

Within 3 weeks from the date of Purchase Order the Manufacturer shall submit a Quality

Assurance Plan for the review of the Owner.

6 Inspection and testing:

6.1 The responsibility for inspection, certification, etc. of all materials, parts lies with the Vendor.

6.2 The Vendor shall specify all of the inspection and testing requirements in the quality plan which

shall identify the activities requiring the Owners approval, review, witnessing etc.

Inspection and testing requirements shall be in accordance with this specification, other All

Equipment shall be inspected for compliances with:

a) Requirement of Owners specification & correspondence therefore.

b) Applicable codes, standards and specifications, which shall also include sub- referenced

standards therein.

c) Test and Inspection Plans produced by the vendor.

6.3 Inspectors have the right to request additional inspections or tests to ensure that the equipment

complies with the specification and all relevant codes & standards.

6.4 Manufacturer shall furnish valid Type Test Certificates of similar models along with the offer. Fresh

type tests for the equipment are not needed, provided the Manufacturer can submit certificatesthat the equipment complies with all type tests as prescribed by IEC/IS Standard specifying the

test requirements for that equipment.

6.5 The routine tests shall include but not necessarily limited to the following:

a) Operation under simulated service condition to ensure accuracy of wiring, correctness of control

scheme & proper functioning of the equipment.

b) All wiring and current carrying part shall be given appropriate High Voltage test.

c) Primary current and voltage shall be applied to all instrument transformers.

d) Routine test shall be carried out on all equipment such as circuit breakers, instrument

transformers, relays, meters etc.


11/21



21


6.6 Routine tests on the equipment shall be carried out as per the relevant IS/IEC. Equipment offered

for final inspection shall be complete and ready for shipment, with the possible exception of the

final paint finish.

6.7 Routine Test certificates to be submitted for Equipment and its all auxiliaries. Type test certificateof similar equipment shall be submitted.

6.8 Vendor to furnish required copies of test certificates, Ref Documents, Drawings, and Instruction

Manuals before Equipment are dispatched.

6.9 Factory acceptance test (FAT) is required to be done at no extra cost to the purchaser. The

purchaser or his representative shall be advised of the tentative date for FAT at least 3 weeks in

advance prior to the test date.

6.10 Any defects found by the TPI or the Owners appointed Inspector shall be rectified in his presence.

Where this is not possible or practical, check lists shall be prepared and signed by the Third Party

Inspector stating all pending items. Copies of these lists shall be sent to the Owner to enable

their subsequent checking. The equipment shall not leave the Vendor factory before all defects

have been rectified and without the written permission of the Owner.

6.11 All spare parts shall be subjected to the same inspection standards and full material certification as

the main order.

6.12 The equipment shall not leave the Vendor / Sub-Vendors factory before all discovered defects

have been rectified and without the written permission of the Owner/Purchaser.

6.13 Any acceptance or release of equipment following an inspection or test activity shall in no way

relieve the Vendor of his contractual responsibility to provide guarantees as to the suitability of the

materials, workmanship and performance of the equipment in accordance with this Specification.

6.14 Owner/Consultant reserves the right to waive the inspection at any stage. Inspection shall be

carried out only on receipt of Vendor's internal test report of the equipment offered and scrutiny of

the same. In the event, on receipt of inspection call, the Owner/Consultants representative

reaches the Vendor's works and finds the material not ready for inspection/incomplete/has short

supply, the inspector will return to his base station and all expenses incurred by the inspector

including to and from travelling expenses from his base station to place of inspection, boarding

and lodging etc shall be reimbursed by Vendor.

7 Vendor documentation:

7.1 All information listed here is to be furnished along with the offer as a minimum.

a) Clause wise comments / deviations on specification in `Table of Compliance [enclosed Appendix

A]. If not furnished, compliance to all requirements in specifications will be binding on the Vendor.

b) Duly filled up Guaranteed Technical Particulars [enclosed Appendix-E].

c) List of components & accessories with Makes.

d) List of recommended spares for two years normal operation with itemised rates.

e) Type test certificates.

f) Technical Catalogues and brochures of major Components.

g) List of clientele for similar equipment in last 5 years.

h) Complete list of special tools (if required)


12/21



21


i) Documents as per RED.

7.2 The Manufacturer shall furnish the drawings and documents as per enclosed Requisition for

Engineering Documents - RED Form [Appendix-D].

7.3 The Owner/Consultant will review drawings submitted by Vendor & return to the Vendor one copy

of drawings with comments to carry out necessary changes, if any, during the engineering /

manufacturing stage.

7.4 The documents required by the Third Party Inspection Agency are not covered under this

specification. The Vendor shall provide all the drawings and documents required by the Third Party

Inspection agency in compliance with the applicable codes and standards.

8 Spares and special tools:

8.1 Spares

The Manufacturer shall furnish list of spares and provide all necessary spares for testing, pre-

commissioning, commissioning. Any of the spares if used during testing/commissioning must be

replenished at no extra cost to the purchaser.

The Manufacturer shall also provide all consumables required during erection up to commissioning.

In addition to above, Manufacturer shall quote separately for Spares required for two years of operation.

8.2 Special tools

The Manufacturer shall include any special tools, which are required for the installation, commissioning,

operation and maintenance of the equipment being supplied. A list of special tools shall be supplied along

with the offer

9 Installation and commissioning:

Vendor shall dispatch Installation and Commissioning instructions at least 2 weeks before the arrival of the

equipment.

Vendor shall provide qualified personnel to supervise the installation and carryout site testing and

commissioning of all equipment supplied under this contract. Prices for these services shall be given

separately.

10 Packing and transportation:

Packing, shipping and delivery of equipment at site and unloading requirements shall be as per relevant

Standard. Vendor to submit the procedure & all the relevant necessary datas / informations along with

offer.

Preparation of the skids for shipment is a crucial step in the completion of this contract. The Vendor must

take in to consideration that all equipment and the skid itself shall be prepared for land transportation.


13/21



21


11 Statutory Approval:

The Equipment supplied shall be acceptable to local Electrical Inspectorate and changes required, if any,

shall be carried out by the vendor without any extra cost.

12 Guarantee:

Equipment shall be guaranteed to meet the specified performance at specified conditions in terms of

power, air flow, thermal performance, design conditions etc.

Equipment and its components shall be guaranteed against faulty design, defective / improper materials

poor workmanship or failure from normal use during the guarantee period.

Vendor shall make all necessary and desirable alterations, repairs and replacement free of charge in the

even of mal performance or defects occurring in the equipment during guarantee period.

Also refer to guarantee clause under Purchase Order.


14/21



21


Appendix-A: Table of Compliance.

The Vendor shall confirm that clauses of the specification have been complied with/accepted or furtherclarifications are desired, or Vendor has taken a deviation with reason thereto.

CLIENT :

M/s. Hindustan Petroleum Corporation Ltd

LPG Bottling Plant project at Bhatinda.

VENDOR REF.

Spec. ClauseNo.

ConformsYes/No

AlternativeYes/No

Clarification

1

2

2.1

2.2

2.3

3

3.1

3.2

3.3

4

4.1

4.2

5

5.1

5.2

5.3

5.4

5.5

5.6

6

7

8

8.1

8.2


15/21



21


CLIENT :

M/s. Hindustan Petroleum Corporation Ltd

LPG Bottling Plant project at Bhatinda.

VENDOR REF.

Spec. ClauseNo.

ConformsYes/No

AlternativeYes/No

Clarification

9

10

11

12

Appendix A:

Appendix B:

Appendix C:

Appendix D:

Appendix E:


16/21



21


Appendix-B: Electrical System Data

[Doc. No. 266763-000-SP-4004BX]


17/21



21


Appendix-C: Codes & Standards.

IS-13585 ( Part I )

:1994

: Shunt capacitors of non self heating types up to & including

1000VIS-1248 ( Part I to IX):2003

: Direct acting indicating analogue electrical measuring

instruments and their accessories

IS-2419 :1979 : Dimensions for panel mounting indicating and recordingelectrical instruments

IS-2705 ( Part I to IV) :1992

: Current Transformer

IS-3156 (Part I to IV)

: 1992

: Voltage Transformer

IS-3231 : 1986 (Part I)

/ (Part II) : 1987

: Electrical Relays for Power System Protection

IS-4146 : 1983 : Application guide for Voltage Transformers

IS-4201 :1983 : Application guide for Current Transformers

IS-4237 :1982 : General Requirements for Switchgear and Control Gear forVoltages not exceeding 1000V AC or 1200V DC

IS 4691 :1985 : Degree of Protection provided by enclosures

IS-4794 ( Part I & II) :1968

: Push Button Switches

IS-5082 :1998 : Wrought aluminium & aluminium alloy bars, rode, tubes andsections for electrical purposes.

IS-6236:1971 : Direct recording electrical measuring instruments.

IS-6875 : Part I : 1973 : Control switches (switching devices for control and auxiliarycircuits including contactor relays) for voltages up to andincluding 1000V AC and 1200V DC.

IS 8623 : ( Part I to II):1983

: Specification for Low-Voltage Switchgear and Control gearAssemblies

IS-9224: Part I ( 1979) : Low Voltage Fuses

IS 10118 :1982 : Code of Practice for Selection, Installation and Maintenance ofSwitchgear and Controlgear

IS 13947 : 1993: Specification for Low-voltage Switchgear and Controlgear

IEC 60947 :2007: Low Voltage Switchgear & Controlgear- Part 1 - General rules

IEC 61439 :2009 :Low voltage switchgear and control gear Assemblies Part 1:Type-tested and partially type-tested assemblies.

IEC 60831-1 :2009

IEC 60931-1: Low voltage capacitors.


18/21



21


Appendix-D: Requisition for Engineering Documents

RED Form

Owner/Purchasers Office Distribution Office

Hindustan Petroleum Corporation Ltd8 S.V. Marg, Ballard Estate

Mumbai- 400 001

Mott MacDonald Consultants (India) Pvt. Ltd.Kothari House, CTS No. 185

Off Andheri - Kurla Road

Andheri (East)

Mumbai 400 059

SPECIAL INSTRUCTIONS Prints Documents shall be sent to:

Production Schedule 4 The Purchasing Office via courier service

Manufacturing, inspection & testing sequence plan 4 The Purchasing Office via courier service

DRAWINGS Required number for TIMING FOR SUBMITTAL

OFFER

APPROVAL

FINAL - for approval 2 weeks after order date

Approval drawings / Final drawings tobe submitted under cover of an ADSform / FDS form respectively

Prints Prints Disk Print - final issue 2 weeks after approvaldate

Documents shall be submitted to:

Submission of Following, but notlimited to:

Guaranteed Technical Particulars 2 4 2 4

General Arrangement Drawingshowing masses, main dimensions

2 4 2 4

Cross section details showingarrangement of auxiliary components,etc.

- 4 2 4

Foundation Plan & Loading details 2 4 2 4Single line diagram, Feeder list - 4 2 4

Block Logic, Schematic & ConnectionDiagrams

- 4 2 4

Bill of Material - 4 2 4

Make of Each Components 2 4 2 4

Type Test, Routine Test Certificates 2 4 2 4

Spares List for two Years Operation 2 4 2 4

As Built Drawing - 4 2 4 Purchasing Office via courier service

SPARE PARTS DOCUMENTS 2 4

ESPIR forms including 1 transparency

TEST AND INSPECTION DOCUMENTS Print

Documents to be submitted under transmittal Documents shall be submitted to:

Manufacturing report 1 4

Test Report / Data Curves 1 4

Calibration Certificates for testing Instruments. 1 4

Bought out Equipments Certificates. 1 4 Purchasing Office via courier servicewithin 4 weeks

of relevant test / inspection.

OPERATING DOCUMENTS Purchasing Office via courier servicenot later than at time of dispatch ofequipment.

Installation instructions 1 4

Operating instructions 1 4 Combine into one manual


19/21



21


Maintenance instructions 1 4

ADDITIONAL REQUIREMENTS

1. Referenced standards / codes shall be the latest issue unless otherwise stated.

REMARKS

Invoice must certify that the drawings andengineering documents specified above have beendispatched to all parties concerned.

Any deviation from the timing for submittal ofdocuments shall be notified to the Approval /Distribution Offices by fax or E mail.

Shop fabrication shall not be started before therequired approval drawings have been released for

construction by the party concerned, unlessotherwise stated on the "Approval DrawingSpecification".

Each document shall bear the item / tag and orderreference number and be dispatched by air mail,unless other instructions are stated on the RED.

Units / dimensions to be used on Engineeringdocuments shall be SI.

The documents shall be in English. Description ondrawings and similar documents may be in otherlanguages provided English translations are also given.

Drawings and documents shall be suitable formicrofilming and comply with accepted national orinternational standards for the preparation of technical

drawings. Only the following standard sizes should beused: A4, A3, A2, and A1.


20/21



21


Appendix-E: Guaranteed Technical Particulars

1. Reference Standard for Capacitor :2. Rating (Total) kVAR :

3. Rated insulation voltage Volt :4. Rated service voltage Volt :5. Rated kVAR of basic unit kVAR :6. Rated frequency Hz :7. Operating temperature C :8. Service life Hours :9. Max. permissible voltage Volt :10.

Max. permissible current Amp :

11.

Capacitance tolerance % :

12

.

Dielectric: material & type :

13.

Dielectric loss w/kVAR :

14.

Total losses w/kVAR :

15.

AC test voltage betweenterminals

Volt :

16.

AC test voltage betweenterminals and case

Volt :

17.

Discharge device details :

18.

Dimension of Panel: WxDxH mm X mm Xmm

:

19.

Weight of Panel kg :

20.

Component Details Make Model/ Cat. No.

a Panel :b Capacitor :c Air Circuit Breaker :d Power Contactor :e Aux. Contactor :f C. T. :g V. T. :h MCB :i APFC Relay :


21/21



21

P:\Kolkata\Engineering\JOBS\OGO-269323-HPCL Bathinda-LPG\ELECTRICAL\03. Issued to client\Capacitor

Appendix-F: Electrical Drawings.

01. Dwg. No. 266763-000-410-002B:- Single Line diagram for PMCC