24 Pocket Handle Dishwasher - Sunset Pointesunsetpointefl.com/downloads/Standard-Appliances-JEspec.pdf · Ø 2 1 /2 " (63.5 mm) 7" (178 mm) Example of Hardwire Installation Note:

For help and assistance with Bosch accessories please visit: www.bosch-eshop.com/eshop/bosch/us or call 1-800-944-2904 Mon-Fri 5am to 6pm PST Sat 6am to 3pm PSTNotes: All height, width and depth dimensions are shown in inches. Please refer to installation instructions prior to making cutout. BSH reserves the absolute and unrestricted right to change product materials and specifications, at any time, without notice. Consult the product’s installation instructions for final dimensional data and other details. Applicable product warranty can be found in accompanying product literature or you may contact your account manager for further details.Warranties: Bosch warrants that the Product is free from defects in materials and workmanship for a period of three hundred and sixty-five (365) days from the date of purchase. The foregoing timeline begins to run upon the date of purchase, and shall not be stalled, tolled, extended, or suspended, for any reason whatsoever. This Product is also warranted to be free from cosmetic defects in material and workmanship (such as scratches of stainless steel, paint/porcelain blemishes, chip, dents, or other damage to the finish of the Product, for a period of thirty (30) days from the date of purchase or closing date for new construction. This cosmetic warranty excludes slight color variations due to inherent differences in painted and porcelain parts, as well as differences caused by kitchen lighting, product location, or other similar factors. This cosmetic warranty specifically excludes any display, floor, “As Is”, or “B” stock appliances.

For more information on our entire line of products, go to www.bosch-home.com/us or call 1-800-944-2904© BSH Home Appliances Corporation. All rights reserved. Bosch is a registered trademark of Robert Bosch GmbH.

Technical Details

Watts (W) 1300 W

Current (A) 12 Amps

Volts (V) 120 V

Frequency (Hz) 60 Hz

Power cord length 56 5/16"

Minimum water pressure (lb/sin)

14

Length inlet hose (in) 60"

Length outlet hose (in) 79"

Dimensions & Weight

Overall appliance dimensions (HxWxD)(in)

33 7/8" x 23 9/16" x 23 3/4"

Required cutout size (HxWxD) (in)

33 7/8" x 23 5/8" x 24"

Adjustable feet Yes

Net weight (lbs) 91 lbs

Accessories—Optional

Dishwasher Supply and Drainage Hose Extension 76 3/4"

SGZ1010UC

Dishwasher 3-Prong Power Cord 66 7/8"

SMZPC002UC

Dishwasher Accessory Kit

SMZ5000

Anti-tarnish Silverware Cassette

SMZ5002UC

General Properties

Number of wash cycles 5

Number of options 5

dBA 44

Third rack Standard

Rack adjustability RackMatic®

Tub material Stainless steel

Control type Buttons

Concealed heating element

Yes

Leak protection system 24/7 AquaStop®

Water softener No

Five-level wash Yes

ChildLock No

Special features InfoLight®, Duo-Flex Silverware Basket, SpeedPerfect™

Efficiency

Water usage per cycle 2.9

Energy efficiency class Tier 1

ENERGY STAR® qualified Yes

Total annual energy consumption (kWh)

259

Total annual water consumption (g)

624

Capacity

Number of place settings 16

SHP65TL5UC Stainless Steel

The new 3rd rack now offers 30% more loading area. Perfect for ramekins, cooking utensils and extra-long silverware.

Features & Benefits

44 dBA - Quietest dishwasher brand.

New 3rd rack adds versatility and offers 30% more loading capacity.

Detergent tray optimizes detergent dissolving.

InfoLight® shines on the floor so you know the dishwasher’s running.

RackMatic® offers 3 height levels, for 9 possible rack positions.

Also available in:White SHP65TL2UCBlack SHP65TL6UC

500 Series DLX – Stainless Steel SHP65TL5UC

24" Pocket Handle Dishwasher



Installation Details

Pre-connected drain hose

Pre-connected inlet hose

Toe-kick

Power cord with junction box

Included:

Image 2: 2013 New Dish NBN

Ø 2 1/2"(63.5 mm)

7"(178 mm)

Example of Hardwire Installation

Note: Cutout required on left or right cabinet wall, depending on location of water inlet, drain and electrical connection

Power cord with junction box included

2 1/2"(63.5 mm)

Image 3a: New Dish NBN

Ø 2 1/2"(63.5 mm)

7"(178 mm)

Example of an Electrical Receptacle Installation

Note: Cutout required on left or right cabinet wall, depending on location of water inlet, drain and electrical connection

Accessorypower cord for

receptacle connectionSMZPC002UC (not included).

2 1/2"(63.5 mm)

Image 3b: New Dish NBN






Note: Plumbing installations will vary - refer to local codes. Drain hose included is 79 (201 cm) and can be extended to a maximum of 155 3/4" (396 cm).

Always use the approved drain hose extension kit (SGZ1010UC).

Ensure a portion of the drain hose is raised between min. 20" (50 cm) and max. 43" (110 cm) above the cabinet floor.

Non-metallic tie

min

20"

(50

mm

)m

ax 4

3" (1

10 m

m)

min

20"

(50

mm

)m

ax 4

3" (1

10 m

m)

Non-metallic tie

Removeplug

Image 5: New Dish NBN



BSMZPC002UC

Product features

o For Models: S36KML**UC, S38KML**UC, S46KML**UC, S48KML**UC, SHE33T**UC,

SHE53T**UC, SHE65T**UC, SHE68T**UC, SHE7PT**UC, SHE8PT55UC, SHP53T55UC,

SHP53TL5UC, SHP65T55UC, SHP65T75UC, SHP65TL5UC, SHP7PT55UC, SHV53T53UC,

SHV53TL3UC, SHV68T53UC, SHV68TL3UC, SHV7PT53UC, SHX53T55UC, SHX53TL5UC,

SHX65T55UC, SHX68T**UC, SHX68TL5UC, SHX7PT55UC, SHX8PT55UC

o Connects your dishwasher to a 110V 3-pin plug outlet/receptable

o Use this power cord for safe, optimal usage of your dishwasher

o Made specifically for our dishwashers. Not to be used with other dishwasher brands

o Do not use other power cords to connect our dishwasher to a 110V 3-pin plug

outlet/receptacle

o 47.25" long

o This item also has a model number of SMZPC002UC



The newly designed full-depth electric slide-in range fits into any freestanding range cutout, and offers a flush built-in look.

Features & Benefits

The new Bosch slide-in range fits in any freestanding range cutout.

Cook with a 6" or a 9" element.

At 4.6 cu. ft., a large oven capacity accommodates most pots and pans.

Genuine European convection for even baking results on multiple levels.

The warming drawer keeps everything you cook warm and ready to serve.

HEI8054UStainless Steel

800 Series – Stainless Steel HEI8054U

30" Electric Slide-in Range

General Properties

Cooking modes Bake, Variable Broil (hi & low), Roast, Warm, Proof Dough, Convection Bake, Convection Broil, Convection Roast, Multi-Rack Genuine European Convection, Convection Conversion, Pizza, Fast Preheat, Sabbath

Cleaning type Self clean

Knob material Metal

Drawer type Warming drawer

Oven Performance

Bake / broil element watts (W)

2,400 / 3,800 W

Convection element watts (W)

2,000 W

Element Performance

Total number of cooktop elements

5

Power of front left element watts (W)

1,400 / 3,000 W

Power of back left element watts (W)

1,200 W

Power of center element watts (W)

100 W

Power of back right element watts (W)

1,200 W

Power of front right element watts (W)

1,100 / 3,200 W

Element Size

Dimension of front left heating element

6" / 9"

Dimension of back left heating element

6"

Element Size (continued)

Dimension of center heating element

6"

Dimension of back right heating element

6"

Dimension of front right heating element

9.5"

Technical Details

Watts (W) 11,300 / 14,800 W

Circuit breaker (A) 40 A

Volts (V); Frequency (Hz) 208 V / 240 V; 60 Hz

Plug type N/A

Cord length (in.) N/A

Energy source Electric

Dimensions & Weight

Overall appliance dimensions (HxWxD)(in.)

35 1/2" x 31 1/2" x 28 7/8"

Required cutout size (HxWxD) (in.)

35 1/2" x 30" x 25"

Adjustable range height (in.)

1 1/2"

Overall Oven Interior Dimensions (HxWxD) (in.)

17 13/16" x 24 1/8" x 18"

Usable Oven Interior Dimensions (HxWxD) (in.)

12 5/16" x 23 1/4" x 15 1/4"


Accessories—Included

Use and care manual, installation guide, standard racks


HEZBS301Low backguard

HEZTR30130" Telescopic rack



This 72" counter-depth French Door refrigerator installs nearly flush and features LED lighting for easier viewing.

Features & Benefits

The internal water dispenser delivers filtered and chilled water.

72" height fills refrigerator cutout precisely, with no unsightly gap.

Clean exterior design for a perfect built-in look.

The LED lighting shines exceptionally bright and saves energy.

Spill-proof glass shelves prevent liquids from running off shelves.

B22CT80SNSStainless Steel

800 Series – Stainless Steel B22CT80SNS

36" Counter-Depth French Door Refrigerator

General Properties

Water filter Yes

Lighting LED

Defrost process refrigerator section

Frost-free

Number of shelves - refrigerator

5

Adjustable shelves - refrigerator

4 half-width

Shelf material - refrigerator

Tempered glass

Type of shelves - refrigerator

Spill-proof glass

Gallon storage bins 2

Humidity control drawer 2

Defrost process freezer section

Automatic

Number of drawers - freezer

3

Ice maker Yes

Quick ice No

Capacity

Total unit gross capacity (cu. ft.) - AHAM

21.8 cu. ft.

Refrigerator gross capacity (cu. ft.)

16.27 cu. ft.

Freezer gross capacity (cu. ft.)

5.52 cu. ft.

Technical Details

Current (A) 15 A

Volts (V) 120 V


Power cord length (in.) 62

Plug type 120V-3 prong

Dimensions & Weight

Appliance dimensions (H x W x D) (in.)

71 7/8" x 35 5/8" x 30 1/8"

Required cutout size (H x W x D) (in.)

72" x 36" x 25 5/8"


Efficiency

ENERGY STAR® qualified No

Energy consumption (kWh/yr)

633 kWh

Accessories—Included

Included Ice scoop




800 Series – Stainless Steel B22CT80SNS

36" Counter-Depth French Door Refrigerator

Leave a 1/2" (1.25 cm) space at the top and 1" (2.54 cm) behind the refrigerator for proper ventilation. For next-to-wall installation,leave 2-1/2" (6.3 cm) minimum on both sides for door opening. It is recommended that you do not install the refrigerator near a heat source such as oven or a range.



30" Over-the-Range Microwave

HMV5052UStainless Steel

Dimensions & Weight

Overall appliance dimensions (HxWxD) (in)

17 1/2" x 29 7/8" x 15 7/8"

Required cutout size (HxWxD) (in)

16 1/2" Min x 30" x 12" Min - 14" Max


General Properties

Cavity color White

Max. microwave power (W)

1,100 W

Max. extraction rate (CFM)

385 CFM

Ducted Yes

Ductless Yes

Duct size 3 1/4" x 10"

Capacity

Cavity capacity (cu. ft.) 2.1 cu. ft.

Turntable diameter (in.) 14 3/16"

Technical Details

Watts (W) 1,550 W

Circuit breaker (A) 15 A

Volts (V) 120 V


Power cord length (in) 39"

Plug type 120V-3 prong

The precisely designed OTR microwave is a perfect match for the Bosch slide-in range or cooktop.

Features & Benefits

A large cooking interior gives you flexibility to cook various dishes.

The OTR microwave is designed to install with a Bosch slide-in range or cooktop.

A multi-speed vent efficiently removes steam, smoke, grease and odors - 385 CFM.

A sensor detects when food is finished and automatically turns off.

The LCD display features easy-to-read white led lettering.

500 Series – Stainless Steel HMV5052U




30" Over-the-Range Microwave

Venting Options

Electrical Connection

Clearance Above Cooktop

500 Series – Stainless Steel HMV5052U

Electric Dryer

PRODUCT MODEL NUMBERS

Front view: Side view:

Back view: Recommended Installation Spacing:

Installation spacing for recessed area or closet installation

The dimensions shown below are the recommended spacing for this dryer.

■ Additional spacing should be considered for ease of installation and servicing.

■ Additional clearances might be required for wall, door, floor moldings, and dryer venting.

■ Additional spacing of 1" (25 mm) on all sides of the dryer is recommended to reduce noise transfer.

■ For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable. Companion appliance spacing should also be considered. W10676165A

04/2014

WED72HED, WED81HED, WED8740D, WED87HED, WED95HED, WED97HED

27"(686 mm)

383/4" Min.(984 mm)

39" Max.(990 mm)

61/2"(165 mm)

297/8"*(759 mm)

31/2"*(89 mm)

61/8"*(156 mm)

143/8"(365 mm)

3/4"*(18 mm)

NOTE: Most installations require a minimum of 5" (127 mm) clearance behind dryer for exhaust vent with elbow. See “Venting Requirements.”

* Approx. measurement.

Power supply cord/cable

Water inlet (Steam models

Vent

18" min.(457 mm)

1"(25 mm)

5"(127 mm)

24 in.2 min.(155 cm2)

48 in.2 min.(310 cm2)

3"(76 mm)

3"(76 mm)

1"(25 mm)

Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation our products, we reserve the right to change materials and specifications without notice. Instructions packed with product. Specifications subject to change without notice.

To supply the required 3 or 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt electrical supply, if specified on the serial/rating plate) on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect to an individual branch circuit.

ELECTRICAL REQUIREMENTS

VENTING REQUIREMENTSExhaust venting: Exhaust your dryer to the outside. 4" (102 mm) diameter vent is required. Rigid or flexible metal exhaust vent must be used. Do not use plastic or metal foil vet. Exhaust hood must be at least 12" (305 mm) from the ground or any object that may be in the path of the exhaust.

The Vent System Chart provides venting requirements that will help achieve best drying performance.

NOTE: Bottom exhaust installations have a 90º turn inside the dryer. To determine maximum exhaust length, add one 90º turn to the chart.

Determine vent path: ■ Select route that will provide straightest and most direct

path outdoors.

■ Plan installation to use fewest number of elbows and turns.

■ When using elbows or making turns, allow as much room as possible.

■ Bend vent gradually to avoid kinking.

■ Use as few 90° turns as possible.

Determine vent length and elbows needed for best drying performance:

■ Use following Vent System Chart to determine type of vent material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified in Vent System Chart. Exhaust systems longer than those specified will:

■ Shorten life of dryer.

■ Reduce performance, resulting in longer drying times and increased energy usage.

Louvered Hood

Angled Hood

Box Hood

Exhaust hoods:Recommended Styles:

Acceptable Style:

Whirlpool Vent System Chart

Number of 90° elbows

Type of vent

Box/louvered hoods

Angled hoods

1

4

3

2

0 Rigid metal

Rigid metal

Rigid metal

Rigid metal

Rigid metal

64 ft. (20 m)

54 ft. (16.5 m)

44 ft. (13.4 m)

35 ft. (10.7 m)

27 ft. (8.2 m)

58 ft. (17.7 m)

48 ft. (14.6 m)

38 ft. (11.6 m)

29 ft. (8.8 m)

21 ft. (6.4 m)

Washer Dimensions:

W10631155A 04/2014

Front-Loading Washer

Recessed or closet installation - stacked washer and dryer

761/2"(1943 mm)

5"(127 mm)

6"(152 mm)

1"(25 mm)

24 in.2

(155 cm2)

48 in.2

(310 cm2)

3"(76 mm)

6"(152 mm)

3"(76 mm)

Recessed area or closet installation (washer only):

1"(25 mm)

24 in.2

(155 cm2)

48 in.2

(310 cm2)

3"(76 mm)

3"(76 mm)

4"(102 mm)

* Add spacing of 1" (25 mm) on all sides of washer.

* Add spacing of 1" (25 mm) on all sides of washer/dryer.

383/4" - 393/4"(948 mm - 1010 mm)

27"(686 mm)

335/16"(846 mm)

523/4"(1340 mm)


WFW88HEA, WFW94HEA, WFW96HEA, WFW95HED, WFW97HED

383/4" - 393/4"(948 mm - 1010 mm)

27"(686 mm)

523/4"(1340 mm) 331/8"

(841 mm)

Washer Dimensions:


WFW61HEB, WFW70HEB, WFW80HEB, WFW8640B, WFW86HEB, WFW72HED, WFW81HED, WFW82HED, WFW8740D, WFW87HED

Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation our products, we reserve the right to change materials and specifications without notice. Instructions packed with product. Specifications subject to change without notice.

ELECTRICAL REQUIREMENTSA 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit serving only this appliance be provided.

Floor drain system requires a Siphon Break Kit (Part Number 285834), 2 Connector Kits (Part Number 285835), and an Extension Drain Hose (Part Number 285863) that may be purchased separately. See “Alternate Parts”. Minimum siphon break height: 28" (710 mm) from bottom of washer. (Additional hoses may be needed.)

Minimum diameter for a standpipe drain: 2" (51 mm). Minimum carry-away capacity: 17 gal. (64 L) per minute. A 1/4" (6 mm) diameter to 1" (25 mm) diameter Standpipe Adapter Kit is available (Part Number 3363920). Top of standpipe must be at least 30" (762 mm) high; install no higher than 96" (2.44 m) from bottom of washer. If you have an overhead sewer and need to pump higher than 96" (2.44 m), a sump pump and associated hardware are needed. See “Alternate Parts”.

Wall standpipe drain system

Laundry tub drain system

Minimum capacity: 20 gal. (76 L). Top of laundry tub must be at least 30" (762 mm) above floor; install no higher than 96" (2.44 m) from bottom of washer.

4.5"(114 mm)

Floor standpipe drain system

4.5"(114 mm)

See requirements for floor standpipe drain system.

30"(762 mm)

min.

4.5"(114 mm)

Floor drain system

DRAIN SYSTEMDrain system can be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Select method you need.

IMPORTANT: To avoid siphoning, only 4.5" (114 mm) of drain hose should be inside standpipe. Always secure drain hose with cable tie.

4"(102 mm)

1"(25 mm)

7"(178 mm)

14"(356 mm)

Custom cabinet installation (washer only):

** Recommended 4" (102 mm), minimum 1.5" (38 mm)

All dimensions show recommended spacing allowed, except for closet door ventilation openings which are the minimum required.For each arrangement, consider allowing more space for ease of installation and servicing, and spacing for companion appliances and clearances for walls, doors, and floor moldings. Space must be large enough to allow door to fully open. Add spacing of 1" (25 mm) on all sides of washer to reduce noise transfer. If a closet door or louvered door is installed, top and bottom air openings in door are required.

Undercounter installation - washer only:

Our Badger 5XP® model provides more power and a longer warranty than the Badger® 5 or Badger® 1.

This model also offers the following features and benefits:

• 3/4 Horsepower Heavy Duty Motor (Quiet Dura-Drive® Induction Motor)

• 3-Year We Come To You® In-Home Parts And Labor Service Warranty

• Rugged Galvanized Steel Construction (For Disposer Durability)

• Space-Saving Compact Design

Submittal Sheet

Job Specifications

SpecificationsType of Feed Continuous

On/Off Control Wall Switch

Motor Single Phase

HP 3/4

Volts 120

HZ 60

RPM 1725

Amp. (Avg. Load) 9.5

Time Rating Intermittent

Lubrication Permanently Lubricated Upper & Lower Bearings

Shipping Weight (Approx.) 15 lbs. 2 oz.

Unit Finish Waterborne Grey Enamel

Overall Height 12-5/8”

Grind Chamber Capacity 26 oz.

Motor Manual ResetProtection Overload

Average Approx. 1 Gallon per Water Usage Person Per Day

AverageElectrical Usage 3-4 KWh per Year

Drain 1-1/2” CushionedConnection Slip Joint

DishwasherDrain Connection Yes

Food Waste Disposers

Dimensions

Food Waste Disposer(s) shall beInSinkErator Badger 5XP®, continuous feed, with 3/4 H.P. motor, galvanized steel grinding elements with two stainless steel 360° swivel lugs. Self-service wrench.

Warranty:3- Year parts and in-home service.

Sample Specification

The complete InSinkErator warranty is included in the Care & Use Booklet packed with each unit.

*

* Distance from bottom of sink to center line of disposer outlet. Add 1/2" when stainless steel sinks are used. ** Length of tailpipe from center line of disposer outlet to end of tailpipe. NOTE: Plumb waste line to prevent standing water in disposer motor housing.

1-800-558-5700www.insinkerator.com

4"

DishwasherDrain

Connection

5"

6"

125/8"

65/16"

The Emerson logo is a trademark and service mark of Emerson Electric Co. The mounting collar configuration

is a trademark of Emerson Electric Co.

InSinkErator may make improvements and/or changes in the specifications at any time, in its sole discretion, without notice or obligation and further reserves the

right to change or discontinue models.

H715-10L-02-02 Printed in U.S.A. © 2010 InSinkErator, InSinkErator is a division of Emerson Electric Co. All Rights Reserved.

Food waste disposers can provide an environmentally responsible alternative to transporting food waste to landfills. And they can help reduce greenhouse gas emissions. At capable wastewater treatment plants, food waste can be recycledto produce renewable energy. Additionally, capable wastewater treatment plants can process food waste into fertilizer. (Check the plant in your area.)

For help and assistance with Bosch accessories please visit: www.bosch-eshop.com/eshop/bosch/us or call 1-800-944-2904 Mon-Fri 5am to 6pm PST Sat 6am to 3pm PSTNotes: All height, width and depth dimensions are shown in inches. BSH reserves the absolute and unrestricted right to change product materials and specifications, at any time, without notice. Consult the product’s installation instructions for final dimensional data and other details prior to making cutout. Applicable product warranty can be found in accompanying product literature or you may contact your account manager for further details.Warranties: Bosch warrants that the Product is free from defects in materials and workmanship for a period of three hundred and sixty-five (365) days from the date of purchase. The foregoing timeline begins to run upon the date of purchase, and shall not be stalled, tolled, extended, or suspended, for any reason whatsoever. This Product is also warranted to be free from cosmetic defects in material and workmanship (such as scratches of stainless steel, paint/porcelain blemishes, chip, dents, or other damage) to the finish of the Product, for a period of thirty (30) days from the date of purchase or closing date for new construction. This cosmetic warranty excludes slight color variations due to inherent differences in painted and porcelain parts, as well as differences caused by kitchen lighting, product location, or other similar factors. This cosmetic warranty specifically excludes any display, floor, “As Is”, or “B” stock appliances.

For more information on our entire line of products, go to www.bosch-home.com/us or call 1-800-944-2904© BSH Home Appliances Corporation. All rights reserved. Bosch is a registered trademark of Robert Bosch GmbH. 09/15

HCREC5UC Recirculation kit

HCPEXT5UCChimney extension for

9-11.5 ft. ceilings

HCIFILTUCFilter kit

HCP30E51UC Stainless Steel

Dimensions & Weight

Overall appliance dimensions (width of canopy included) (HxWxD) (in.)

24 9/16"–38 7/8" /28 1/4"–42 9/16"x 30" x 19 11/16"

Height of the chimney (in.)

19 9/16"–33 7/8" / 23 1/4"–42 9/16"

Required distance above cooktop/range cooking surface

24" Electric / 30" Gas

Diameter of air duct (in.) top

8"



General Properties

Operating mode Convertible: ducted /recirculating

Maximum CFM 300 CFM

Sones 5.36 HS / 1.56 WS

Number of speed settings

3-stage

Motor location Integrated motorin hood chimney

Number of lights 1

Bulb type Fluorescent

Total power of the lamps (W)

13 W

Damper included Yes

Grease filter material Aluminum

Grease filter type Multilayer cassette

Technical Details

Volts (V) 120 V


Plug type No plug

The ENERGY STAR® hood is quiet in operation providing better efficiency and comfort with less noise.

Features & Benefits

Touch controls with LCD display.

300 CFM centrifugal integrated blower included.

Three speed touch controls with LCD display.

Dishwasher safe aluminum mesh filters.

Converts to recirculation mode with accessory kit (separate purchase required).

300 Series – Stainless Steel HCP30E51UC

30" Pyramid Canopy Chimney Hood

For help and assistance with Bosch accessories please visit: www.bosch-eshop.com/eshop/bosch/us or call 1-800-944-2904 Mon-Fri 5am to 6pm PST Sat 6am to 3pm PSTNotes: All height, width and depth dimensions are shown in inches. BSH reserves the absolute and unrestricted right to change product materials and specifications, at any time, without notice. Consult the product’s installation instructions for final dimensional data and other details prior to making cutout. Applicable product warranty can be found in accompanying product literature or you may contact your account manager for further details.Warranties: Bosch warrants that the Product is free from defects in materials and workmanship for a period of three hundred and sixty-five (365) days from the date of purchase. The foregoing timeline begins to run upon the date of purchase, and shall not be stalled, tolled, extended, or suspended, for any reason whatsoever. This Product is also warranted to be free from cosmetic defects in material and workmanship (such as scratches of stainless steel, paint/porcelain blemishes, chip, dents, or other damage) to the finish of the Product, for a period of thirty (30) days from the date of purchase or closing date for new construction. This cosmetic warranty excludes slight color variations due to inherent differences in painted and porcelain parts, as well as differences caused by kitchen lighting, product location, or other similar factors. This cosmetic warranty specifically excludes any display, floor, “As Is”, or “B” stock appliances.

For more information on our entire line of products, go to www.bosch-home.com/us or call 1-800-944-2904© BSH Home Appliances Corporation. All rights reserved. Bosch is a registered trademark of Robert Bosch GmbH. 09/15


300 Series – Stainless Steel HCP30E51UC

30" Pyramid Canopy Chimney Hood

A Lower �ue ductB Upper �ue duct

A Ducted operation:Min. / Max. 24 9/16" (624 mm) / 38 7/8" (985 mm)Recirculation mode:Min. / Max. 28 1/4" (716 mm) / 42 9/16" (1081 mm)

measurements in inches (mm)

Documents

24 Pocket Handle Dishwasher - Sunset Pointesunsetpointefl.com/downloads/Standard-Appliances-JEspec.pdf · Ø 2 1 /2 " (63.5 mm) 7" (178 mm) Example of Hardwire Installation Note: