Upload
others
View
8
Download
0
Embed Size (px)
Citation preview
23. Mechanical tying of Rebar
1) What is mechanical tying of rebar?It is essential construction method for large scale civil engineering construction such
as high-building, bridge, dam, etc and underground building anti-earthquake plan and
also special construction. It is a splice method for strong economic quality assurance if
folded tying method is impossible in case rebar arrangement with density and rebar
diameter is bigger and so by the increase of rebar strength & concrete strength. It is
applicable for deformed rebar to use rebar concrete building. In foreign countries, it
was verified from 1960 and it is using for Korean construction site from mid-1990.
2) Type of mechanical tying of rebar
3) Screw-type tying of rebarrebar warehouse-in → make rebar screw process drawing → start processing of screw type
→ deliver to construction site(3~10days from order date)
screw type
inflationtype
compressiontype
joint ribcut type
tapertype
others
mortarinjection type
gascompression
hydrauliccompression type
site tie type
joint fixed bodyadhesion type
joint rib compressedjack adhesion type
processtype
process type inflation type compression type joint rib cut type taper type
inflate of rebar processingpart largely by mold(example) rebar 25mm - M30case screw type
bury rebar joint rib bymold (example) rebar25mm - M25.5
processing screw after deletingrebar joint rib with fixed size(example) rebar 25mm - M26
screw processing withangle of rebar front end
prove the confidenceafter processing of lowcarbon steel bar(SD300)available for largeproduction
prove the confidence afterprocessing of low-midcarbon steel bar(SD300,400)available for largeproductionavailable for production onconstruction site
prove the confidence afterprocessing of low-mid-high carbon steelbar(SD300,400,500)available for large productionavailable for production onconstruction site
prove the confidenceafter processing of lowcarbon steel bar(SD300)available for productionon construction site
the inflation processing endmight has low confidence ifit is caused by processingvulcanization of mold incase high carbon steel barlow confidence afterbinding 2 rebarslow confidence in case ofbending
the compressionprocessing end might haslow confidence if it iscaused by processingvulcanization of mold incase high carbon steel barlow confidence in case ofbending
coupler size is 10%longer than inflation &compression type by thedeviation of size ofrebar joint & rib
low confidence ofomission & untying fortesting tension strengthand repeat test
case screw type case screw type cut screw typescrew processing
merit
demerit
4) Site connection-type tying of rebaroutbreak of splice → carry-in of parts(arrival to site within 12hours after ordering) →assembly & construction carry-out → inspection comparing other splice part
process type
classification joint fixed body adhesion type joint rib compressed jack adhesion typeprecision processing & molding per part of splicepart base on joint groove of rebar(no artificialprocessing of rebar)
precision processing & molding per part of splicepart base on nominal diameter of rebar(no artificialprocessing of rebar)
available to assemble without processing screw onrebar
available to assemble without processing screw onrebarease to bind regardless of rebar type(foreign &domestic rebar , deformed rebar , comb-patternrebar , X type)available for large production per rebar title
need pre-education for building assembleravailable for deformed rebar only in Korea and lowconfidence of binding in case disorder of toleranceof rebar joint rib and trademarkneed pre-education for building assembler
merit
demerit
inflation screw swage screw joint-rib screw taper screw
cut processing cut processing cut processing cut processing
pre-cut after mold inflation mold compression pre-cut processing angle processing
case screw case screw case screw cut screw
lock nut fixed pincompression jack
lock coupler
connection jack
fixed bodyrebar
length after bindingoute
r dia
met
er o
f cou
pler
double facedcoupler
5) Other tying of rebar
process type
classification mortar injection type gas compression type hydraulic compression type
splice part to perform platform onrebar joint & rib groove & insideof connection part
heat & compression splicemethod of both ends of rebar byusing oxygen & acetylene
splice method to adhere sleeve bypressing outside sleeve afterclosing rebar to soft sleeve
using to pre-cast(PC) spliceconstruction method
using in Japan mostly and provethe confidence of tensioncompression
using in europe partly
splice part is large and longexcessively and low confidenceper rebar typedifficulty of confidence proofof construction site carry-outproduct
big tolerance of constructionsite carry-out per condition oftemperaturedifficulty of confidence proofof construction site carry-outproducttroublesome of purchaseseparately of compressed rebarfor compression reinforcementto classify to producecompression bar & regular bar
difficulty of reinforcementbecause the possibility ofdisplacement of pressurestrength for 1pc & 100pcs andalso the movement of pressuretool
merit
demerit