Upload
childofheaven
View
89
Download
3
Embed Size (px)
Citation preview
Standards
Approved
Checked Against
Checked Designer
Part No.
Modify
GEBERIT CompetenceCenter Shanghai(China)
Modify
persons or use it for other activities.allowed to copy this or give it to third
Without our written permission nobody is
All rights are reserved for this document.
Modify
00170.586.00.0
Signed by
Scale
1:1
Designed by
Production
Logistics
Purchase
Quality
Paper
Printing
Type:
Dimension:
Color:
Sides:
Colors:
Two sides
WhiteA3+A4
Ruthy 27/08/09Black & Red
Geberit Installation Instruction
Page 1/6
80 g/m2
Layout
Released
P2 P3 P4P1P5 P6
Don
't pr
int t
his
rect
angl
e o
ut请
不要
将此
线框
印刷
出来
FFL0
46-60
FFL
103
59
5
16-29
Hf
45
8
0
459
8
55
57
85
465
16-29
Hf
0-4
0
170.586.00.0(00)
46-60
Bend supplied metalstraps and install asrequired.
Hf = Height of flush pipe, dimension
to WC suppliers specification
Left rail in front of right rail.
1 Layout
2 Fasten cistern
Geberit Installation InstructionArt.No.224.383.00.1
All measurements in cm (1 cm = 10 mm)
Hf = Height of flush pipe,dimension to WC suppliers specificationNote:Add necessary precautions in case of condensation risk!
Pages 1 to 3 of this installation instruction shows only the basic layout for front access cistern installation. Page 5 shows additional schematic layout for rear access installation options. Page 6 shows the basic layout for front access brick installation. The cistern and HyTronic actuator can be installed in several different positions. Confirm with the bathroom designer the required installation details or alternatively refer to product brochure. Provision for a sufficiently sized removable service panel is strictly required. This removable panel has to provide full access to the service opening of the cistern. Also consider that the service personnel require sufficient room to perform maintenance through the service opening.
Install a removable access or cover plate centered over the service opening of the cistern. Minimum size W28cm x H14cm.
See electronic components montage sheet for additional information
Waste position to WC suppliers specification. Waste fittings by others.
59
16-29
103
5
Hf
487
0 FFL
55
44
948
42
-1-
If cavity is deeper than 9 cm keep front part of the access opening flush with studs at the front.
If cavity is 9 cm deep keep back of cistern flush with back of stud wall. Cistern can also be reverse mounted.
Assemble and installrail as shown below.
I f cav i t y i s 9cm deep back o f cistern flush with back of studs.
I f cavi ty is deeper than 9cm keep front part of the access opening flush with studs at the front.
0 = FFL = Finished floor level
8
9
Waste
Waste
FFL
0-4
Netz
teil N
TW
C 0
3882 1
84 0
0 0
IN 2
30v/5
0H
z/1
00m
AO
UT 3
.5-4
.2V
=/5
00m
AF1 2
A/2
50V
TH
SE
V
VD
E
964.338.00.0SY03/03
230-240V50-60Hz
Standards
Approved
Checked Against
Checked Designer
Part No.
Modify
GEBERIT CompetenceCenter Shanghai(China)
Modify
persons or use it for other activities.allowed to copy this or give it to third
Without our written permission nobody is
All rights are reserved for this document.
Modify
00
Signed by
Scale
1:1
Designed by
Production
Logistics
Purchase
Quality
Paper
Printing
Type:
Dimension:
Color:
Sides:
Colors:
Two sides
WhiteA3+A4
Black & Red
Geberit Installation Instruction
Page 2/6
80 g/m2
Layout
Released
P1P5 P6 P4P2 P3 170.586.00.0
Ruthy 27/08/09
Don
't pr
int t
his
rect
angl
e o
ut请
不要
将此
线框
印刷
出来
4 Flush pipe installation
3 Flush pipe preparation
5 Stop valve installation
Geberit Installation Instruction
-2-
0FFL
Ensure that flush pipe bend is installed plumb.
1/2" female tube bush( not supplied )
Use suppliedgrommet
Flush line befor
Remove servicecover
connecting hose
Hexagon of tube bushto be inside the cistern.
Max. 65
Fully open
oo
Chamfer the insideCut flush pipe bendto required length edge of the cut.
Lubricate o-ring(lubricant supplied)
Push flush pipe over cistern spiggot. Allow for 2 cm clearance when flushpipe bend is adjusted to the requiredinstallation eight Hf . This will alsoprovide for an additional 2 cmadjustment (up or down) if required later.
Push flush pipe over cistern spiggot. Allow for 2 cm clearance when flushpipe bend is adjusted to the requiredinstallation eight Hf . This will alsoprovide for an additional 2 cmadjustment (up or down) if required later.
A B C
DThis procedure is only for the supplied black flushpipe bend and not for the flush pipe adaptor kit
46-60
Left rail in front of right rail.3434
Secure flush pipe bendwith supplied bracket "A".Pipe to be held firmly butshould still be moveable upor down if so required later.
36
Assemble and installrail as shown below.
For a longer flush pipethan the minimum lengthof 16 cm increase theminimum distance of therail by the same amount.eg.: flush pipe 17 cm = rail distance 14 cm
16-29
13-23
Hf0 FFL
A
5
5
16-29
2
Hf
Hf
9090
Standards
Approved
Checked Against
Checked Designer
Part No.
Modify
GEBERIT CompetenceCenter Shanghai(China)
Modify
persons or use it for other activities.allowed to copy this or give it to third
Without our written permission nobody is
All rights are reserved for this document.
Modify
00
Signed by
Scale
1:1
Designed by
Production
Logistics
Purchase
Quality
Paper
Printing
Type:
Dimension:
Color:
Sides:
Colors:
Two sides
WhiteA3+A4
Black & Red
Geberit Installation Instruction
Page 3/6
80 g/m2
Layout
Released
P1P5 P6 P4P2 P3 170.586.00.0
Ruthy 27/08/09
Don
't pr
int t
his
rect
angl
e o
ut请
不要
将此
线框
印刷
出来
Fig. 4
B
Fig. 3Fig. 2Fig. 1
6 Testing
9 Kee seal
Geberit Installation Instruction
-3-
Before the wall is closed cistern must be tested.1. Open stop valve (Fig.1).2. Fill cistern and install inner cover (Fig.2A).3. Check water tightness. Insert protection plug into the flush bend opening and secure it with tape. Leave cistern under test (refer to standard) (Fig.3B).4. Final water tightness test. Remove protection plug and empty the cistern completely. (lift flush valve) Insert protection plug and secure it with tape (Fig.4).
The cistern is supplied with two different sized kee seals. The kee seal with an outside diameter of 6 cm seals flush pipe holes in the ceramic sized 5.3 cm to maximum 5.7cm.The kee seal with an outside diameter of 6.7 cm seals flush pipe holes in the ceramic sized 5.6 cm to maximum 6.2 cm.
Flush pipesThe cistern is supplied with a 18 cm long flush pipe for concealed installations. As an accessory longer flush pipes for in-duct installations are available. For installations with an exposed flush pipe there are also a variety of finishes and materials available. Enquire with your supplier.
A
7 Fit tiling template
Fit styrofoamtiling template
Do a final check on the required flush pipe heightHf.
Hf0 FFL
8
Wall sheeting and tiles shall be cut up to the edge of the tiling template.
Access plateThis installation requires an access plate. For product selection refer to product brochure.
Standards
Approved
Checked Against
Checked Designer
Part No.
Modify
GEBERIT CompetenceCenter Shanghai(China)
Modify
persons or use it for other activities.allowed to copy this or give it to third
Without our written permission nobody is
All rights are reserved for this document.
Modify
00
Signed by
Scale
1:1
Designed by
Production
Logistics
Purchase
Quality
Paper
Printing
Type:
Dimension:
Color:
Sides:
Colors:
Two sides
WhiteA3+A4
Black & Red
Geberit Installation Instruction
Page 4/6
80 g/m2
Layout
Released
P1P5 P6 P4P2 P3 170.586.00.0
Ruthy 27/08/09
Don
't pr
int t
his
rect
angl
e o
ut请
不要
将此
线框
印刷
出来
-4-
If the 224.383.00.1 is installed elevated and requires a longer flush pipe use the supplied Adaptor kit. To fabricate the required length see (Fig.A & B).
The adaptor kit includes only the adaptor socket & spacer, the required 40mm DWV pipe & bend are not supplied.
Note: With 40 mm DWV PVC pipe the supplied Geberit kee seals will seal 0.1 cm less than the maximum diameters stated on page 3 in section 10 of the 224.383.00.1 installation instructions.If the adaptor kit is used then the supplied black flush pipe bend and flush pipe are no longer required. Do not attempt to join these parts to PVC.
Adaptor supplied
4 0 D W VP V C Pipenot supplied
4 0 D W V P V C b e n d not supplied
40 DWV PVC Pipe connection to toilet not supplied
fig.A
Push flush pipe adaptor over cistern spiggot. Allow for 3 cm clearance whenflush pipe is adjusted to the requiredinstallation height Hf . This will also provide for an additional 1 cm adjustment(up or down) if required later on in theconstruction.
5
43
Hf
Outlet spigot 224.383 cistern
Lubricate o- rings lubricant supplied
Adaptor Kit Art.No.225.057.00.1
Install black spacerbetween PVC pipeand pipe bracket
Pipe bracket suppliedwith cistern
fig. B
40 DWV PVC pipe workjointed this side
Geberit Installation Instruction
10 Flush pipe adaptor kit
Standards
Approved
Checked Against
Checked Designer
Part No.
Modify
GEBERIT CompetenceCenter Shanghai(China)
Modify
persons or use it for other activities.allowed to copy this or give it to third
Without our written permission nobody is
All rights are reserved for this document.
Modify
00
Signed by
Scale
1:1
Designed by
Production
Logistics
Purchase
Quality
Paper
Printing
Type:
Dimension:
Color:
Sides:
Colors:
Two sides
WhiteA3+A4
Black & Red
Geberit Installation Instruction
Page 5/6
80 g/m2
Layout
Released
P1P5 P6 P4P2 P3 170.586.00.0
Ruthy 27/08/09
Don
't pr
int t
his
rect
angl
e o
ut请
不要
将此
线框
印刷
出来
Geberit Installation Instruction
-5-
Install hoses & hardware for Control Panel in preferred location: A, B or C(see also HyTronic installation instructions)
Further Installation Examples
The 224.383.00.1 cistern allows for greater flexibility in the positioning of cistern and HyTronic actuator. See following installation examples. Confirm with the bathroom designer the required installation details or alternatively refer to product brochure. Provision for a sufficiently sized removable service panel is strictly required.
Stud wall installation with rear access (for floor mounted wall faced pan)Cavity depth 9 cm
Note all other installation dimensions and steps are as 2 to 10 on page 1 to 3. The only exception is to swivel flush pipe bend 180° .
Adjacent room this side, service opening this side (rear access).
Side viewIf cavity is deeper than 9 cm keep front part of the service opening flush with studs at the rear.
Install a removable access panel centred over the service opening of the cistern. Minimum size W 28cm x H 14cm.
If cavity is 9 cm deep keep back of cistern flush with front of stud wall.
Bathroom this side
Turn flush pipe bend to this side.
Rear view Side view
Hf= Height of flush pipe, dimension to WC suppliers specification
View from Bathroom View from Bathroom View from Bathroom
HyTronic top mounted HyTronic corner mountedHyTronic side mounted
FFL0
B
FFLHf
46-60
45
103
59
7
16-29
FFL
9
Waste
Waste
FFL0
or Left RightA
C
Right or Left
Bathroom this side
Brackets supplied
55
16-29
459
Hf
5
85
465
87
FFL
Note: Children may have problems reaching the button.
Standards
Approved
Checked Against
Checked Designer
Part No.
Modify
GEBERIT CompetenceCenter Shanghai(China)
Modify
persons or use it for other activities.allowed to copy this or give it to third
Without our written permission nobody is
All rights are reserved for this document.
Modify
00
Signed by
Scale
1:1
Designed by
Production
Logistics
Purchase
Quality
Paper
Printing
Type:
Dimension:
Color:
Sides:
Colors:
Two sides
WhiteA3+A4
Black & Red
Geberit Installation Instruction
Page 6/6
80 g/m2
Layout
Released
P1P5 P6 P4P2 P3 170.586.00.0
Ruthy 27/08/09
Don
't pr
int t
his
rect
angl
e o
ut请
不要
将此
线框
印刷
出来
Geberit Installation Instruction
-6-
Brick wall installation (with floor mounted wall faced pan) order Art.No.813.362.00.1 with cistern
HfFFL Waste
Allow for sufficient blockout for cistern installation
Fasten cistern andflush pipe to brick wall
Install Styrofoam PackingArt.No. 813.362.00.1
Note: All other installationdimension are as per stud wallinsta l lat ion and aremeasured from the finished floor
Fill in space betweencistern and wall
Fix rendering mesh Render and tile
Tape gaps
Removable accesscover plate of panel has to be provided
Hf=Height of Flush pipe connection depends on the to toilet model.
Note:All construction dimensions, material, methods and details shown are indicative only. The final sizing, material used and construction methods must be determined by Project Architects, Builder, Engineer and local standard. This edition ; Date:27.8.2009; File name: supercedes all previous editions.
0
Use package tube Art. No: 225.056.00.1 (not supplied)
1
42 3
In-ceiling installation, separate ceiling access.
Cistern serviceopening
FFL
Waste
Hf
Approx. 1m
Ceiling Void
ServicePanel or alternative access
Min. 90mm
Max. 3.5m
Side View Front View
Water connection ½” male
Use extension set Art. No. 117.041.00.1where necessary(max. 3.3m)
PVC Adaptor
Flush pipe 40mm DWV PVC (not provided)
Max.45º bend
Hf
Hf= Height of flush pipe, dimension to WC suppliers specification