2016 UPC Report on Proposals

Information on IAPMO Codes and Standards Development 1. Applicable Regulations. The primary rules governing the processing of the Uniform Plumbing Code and Uniform Mechanical Code are the IAPMO Regulations Governing Committee Projects (RGCP). Other applicable rules include Bylaws, Assembly Consideration Session Rules, Technical Meeting Convention Rules, Guide for the Conduct of Participants in the IAPMO Codes and Standards Development Process, and the Regulations Governing Petitions to the Board of Directors from Decisions of the Standards Council. For copies of these documents, contact the Code Development Department at IAPMO World Headquarters at 4755 E. Philadelphia Street, Ontario, CA 91761-2816 USA, or at 909-472-4100. These documents are also available at the IAPMO website at www.iapmo.org.

The following is general information on the IAPMO process. All participants, however, should refer to the actual rules and regulations for a full understanding of this process and for the criteria that govern participation.

2. Technical Committee Report (TCR). The Technical Committee Report is defined as the Report of the Technical Committee and Technical Correlating Committee (if any) consisting of the Report on Proposals (ROP), as modified by the Report on Comments (ROC), published by the Association (see 1-4 of RGCP).

3. Report on Proposals (ROP). The ROP is defined as a report to the Association on the actions taken by Technical Committees and/or Technical Correlating Committees, accompanied by a ballot statement and one or more proposals on text for a new Document or to amend an existing Document (see 1-4 of RGCP). The ROP and the ROC together comprise the Technical Committee Report. Anyone who does not pursue an issue as a proposed amendment of the Association Meeting will be considered as having their objection resolved.

4. Assembly Comment. The Assembly Consideration Session, held during the second year of the code development cycle, will be held during IAPMOs annual conference from September 25-29, 2016, in Albuquerque, New Mexico. The Assembly Consideration Session is scheduled for September 27, 2016. Anyone in the Assembly who objects to an action of the Technical Committee, as published in the ROP, may make a motion in accordance with Section 4-4.3.1.2 of the RGCP and, if such motion is sustained by majority vote, both the TC action established by a letter ballot and the Assemblys action, which shall be considered as a comment in accordance with Section 4- 4.3.1, shall be included in the ROC.

5. Report on Comments (ROC). The ROC is defined as a report to the Association on the actions taken by Tech- nical Committees and/or Technical Correlating Committees accompanied by a ballot statement and one or more comments resulting from public review of the Report on Proposals (ROP) (see 1-4 of RGCP). The ROP and the ROC together constitute the Technical Committee Report. Anyone who does not pursue an issue, either in person or by designated representative in accordance with Section 4-5.4(c) of the RGCP, as a proposed amendment of the Association Meeting will be considered as having their objection resolved.

6. Association Amendments. The Technical Committee Reports, consisting of the ROP and ROC, will be presented at the Association Technical Meeting Convention for action. This meeting, held during the final year of the code development cycle, will be held during IAPMOs annual conference from September 24-28, 2017, in Anchorage, Alaska. Amending motions made to the Technical Committee Reports may be made only at the Association Technical Meeting Convention in accordance with 4-5 and other applicable sections of the RGCP. Amending motions may be made in person or by a designated representative in accordance with Section 4-5.4(c) of the RGCP. Objec- tions are deemed to be resolved if not pursued at this level.

7. Council Appeals. Anyone can appeal to the Standards Council concerning procedural or substantive matters related to the development, content, or issuance of any Document of the Association or on matters within the purview of the authority of the Council. Such appeals must be in written form and filed with the Secretary of the Standards Council (see 1-6 of RGCP). Time constraints for filing an appeal must be in accordance with 1-6.2 of the RGCP. Objections are deemed to be resolved if not pursued at this level.

8. Document Issuance. The Standards Council is the issuer of the Uniform Plumbing Code and Uniform Mechan- ical Code. The Council acts on the issuance of a Document within sixty days from the date of the recommendation from the Association Technical Meeting Convention, unless this period is extended by the Council (see 4-7 of RGCP).

9. Petitions to the Board of Directors. The Standards Council has been delegated the responsibility for the admin- istration of the codes and standards development process and the issuance of documents. However, where extraor- dinary circumstances requiring the intervention of the Board of Directors exist, the Board of Directors may take any action necessary to fulfill its obligations to preserve the integrity of the IAPMO codes and standards development process. The rules for petitioning the Board of Directors can be found in the Regulations Governing Petitions to the Board of Directors from Decisions of the Standards Council and in 1-7 of the RGCP.
http://www.iapmo.org/

To: IAPMO Members and Other Interested Parties

Date: August 2016

Enclosed is your 2016 Report on Proposals (ROP). These proposals were presented to the Plumbing Technical Committee who met in Denver, Colorado on May 2 - 4, 2016.

At the Annual Education and Business Conference, which will be held September 25 29, 2016, in Albuquerque, New Mexico, IAPMO members and others attending the conference will have the opportunity to discuss and debate these proposals during the Assembly Consideration Session.

All comments for consideration by the Technical Committee should be submitted to IAPMO by January 3, 2017.

On May 1 5, 2017, the Technical Committee will consider all of the comments received in response to the actions contained within the ROP and will vote on whether to modify any of their previous actions.

Thereafter, from September 24 28, 2017, IAPMO will be holding its 87th Annual Education and Business Conference in Anchorage, Alaska. The IAPMO voting membership present at that conference will then vote on the actions taken by the Technical Committee during the Technical Meeting Convention. Please visit the IAPMO web site at www.iapmo.org for more information on the consensus code development process and timeline.

Following the ROP is a preprint of the Uniform Plumbing Code, as it would appear in the event that all of the proposals accepted by the Plumbing Technical Committee in May 2016 are ultimately approved for inclusion in the final version of the 2018 edition of the Uniform Plumbing Code. This preprint is provided to you as a courtesy. All changes are tentative and subject to revision. This document is not to be considered the final version of the 2018 Uniform Plumbing Code. Specific authorization from IAPMO is required for republication or quotation.

THE BALLOT RESULTS ON ALL COMMITTEE ACTIONS ON PROPOSALS PASSED EXCEPT FOR THE FOLLOWING THREE ACTIONS:

ITEM 186 FAILED TO ACHIEVE THE NECESSARY 2/3 AFFIRMATIVE VOTE OF RETURNED BALLOTS. ITEM 192 FAILED TO ACHIEVE THE NECESSARY 2/3 AFFIRMATIVE VOTE OF RETURNED BALLOTS. ITEM 211 FAILED TO ACHIEVE THE NECESSARY 2/3 AFFIRMATIVE VOTE OF RETURNED BALLOTS.

In accordance with Section 4-3.5.2 where the technical committee actions failed to achieve the necessary 2/3 affirmative vote, a public comment is requested for each proposal listed above. All proposals listed above shall be reconsidered by the technical committee as an automatic public comment.

Linden Raimer Chair

IAPMO Standards Council

Gabriella Davis Recording Secretary

IAPMO Standards Council

Dan Daniels Chairman

Plumbing Code TC

April Trafton Chairperson

Mechanical Code TC
http://www.iapmo.org/

PLUMBING TECHNICAL COMMITTEE (as of 03/10/2016)

NAME REPRESENTATION CLASSIFICATION Dan Daniels, Chairman Pueblo, CO Enforcing Authority

Domenico Barbato, Principal Mark Casey, Alternate

City of Los Angeles Department of Building and Safety Enforcing Authority

Amir Tabakh City of Los Angeles Department of Water and Power Enforcing Authority

Bob Adler City of San Jose, California Enforcing Authority

John Nielsen State of Idaho Div. of Building Safety Enforcing Authority

Bruce Pfeiffer, Ex-Officio* IAPMO Enforcing Authority*

Arnie Rodio, Jr., Principal Arnie Rodio, Sr., Alternate

Pace Setter Plumbing Installer/Maintainer

Jim Stack Plumbing-Heating-Cooling Contractors National Association

Installer/Maintainer

Larry Soskin Ace Duraflo Installer/Maintainer

Sarah Aguilar Southland Industries Installer/Maintainer

Sylvanus Bloice Roots Plumbing Services Installer/Maintainer

Martin Mo Salberg, Principal Carl Cimino, Alternate

Plumbers, Steamfitters and Refrigeration Fitters UA Local 393

Pipe Trades Training Center Labor

DJ Berger, Principal Plumbers & Steamfitters Labor

Phil Campbell, Principal James Pavesic, Alternate

United Association Labor

David L. Mann, Principal Che Timmons, Alternate

CA Pipe Trades Council Plumbers and Steamfitters Local 342

Labor

Pennie Feehan Copper Development Association Manufacturer

Matt Sigler Plumbing Manufacturers International Manufacturer

Richard Church, Principal Michael Cudahy, Alternate

Plastic Pipe and Fittings Association Manufacturer

William LeVan, Principal James Walls, Alternate

Cast Iron Soil Pipe Institute Manufacturer

Ian Chang Intertek Testing Services Research/Standards/ Testing

Jeremy Brown, Principal Terry Burger, Alternate

NSF International Research/Standards/ Testing

Maggie Carroll, Principal John Taecker, Alternate

Underwriters Laboratories Research/Standards/ Testing

Doug Marian, Principal Don Summers, Alternate

ASSE Research/Standards/ Testing

Laura Montville, Principal* Eric Nette, Alternate

NFPA Research/Standards/ Test Laboratory

Anthony Scarano Plastics Piping Consultant Special Expert

April Trafton Donald Dickerson Associates Special Expert

Julius Ballanco, Principal Billy Smith, Alternate

American Society of Plumbing Engineers Special Expert

Phil Ribbs, Principal Leonard Ramociotti, Alternate

PHR Consultants LAR Consulting

Special Expert

Donald Surrena, Principal Dan Buuck, Alternate

National Association of Home Builders User

Thomas Pape Alliance for Water Efficiency (AWE) Consumer

John Jack Fischer Self Consumer

Enrique Gonzalez, Staff Liaison IAPMO Staff

Total Voting Members: 29 *Total Non-Voting Members: 2

The above listed TC Members are in order of classification (see far right column).

FORM FOR COMMENTS ON IAPMO UPC/UMC COMMITTEE DOCUMENTS-2015

NOTE: All Comments MUST be received by 5:00 PM PST on January 3, 2017 PLEASE USE SEPARATE FORM FOR EACH COMMENT Forms to be submitted electronically and accessed at the following:

http://codes.iapmo.org/form_comments_upc_umc_2018.aspx

Date Name Tel. No. ____________________

Organization Email Address

Street Address State Zip. Please Indicate Organization Represented (if any)

Recommendation:

Check one (see instructions) Add new text Revise text Delete text without substitution

Section number: Code: UPC UMC Comment on Proposal Item number: Proposed Text [Note: Proposed text must be in legislative format i.e., using underscore to denote wording to be inserted (wording) and strike through to denote wording to be deleted (wording].

Statement of Problem and Substantiation/Resolution:

Are you referencing standards in your comment? Check one Yes No If yes, please provide two hard copies or one electronic copy with your comment. Please note that if a standard is referenced above in your comment you must submit such standard in order for your comment to be processed. If the standard is not received by the closing date, your comment is considered incomplete and will not be processed.

Where additional supplementary materials such as tests, research papers, or other documents need to be submitted, please provide supporting material electronically. Please note that if supporting material is not received by the closing date, it will not be accepted for review by the Technical Committee. Copyright Assignment (This comment is original materials and is considered to be the submitters own idea based on, or as a result of, research and experience, and is not copied from another source). I hereby irrevocably grant and assign IAPMO all and full rights in copyright, in this proposal. I understand and intend that I acquire no rights, including rights as a joint author, in any publication of IAPMO in which this comment in this or another

similar or analogous form is used. I hereby warrant that I am the author of this comment and that I have full power and authority to enter into this copyright assignment. By checking this box I affirm that I am, and agree to be legally bound by the above Copyright Assignment and the terms and conditions contained therein. I understand and intend that, by checking this box, I am creating an electronic signature that will, upon my submission of this form, have the same legal force and effect as a handwritten signature.

Note: If you are not the author of this comment (this text is copied from another source) please do not submit. The author of the comment must give copyright assignment (which is the submitters own idea based on or as a result of research, experience and is not copied from another source).

Patent Policy. IAPMOs patent policy is to adhere fully to the ANSI patent policy. Every proponent of a code change proposal should familiarize him or herself with the ANSI patent policy which is available in its entirety at www.ansi.org/essentialrequirements. Upon receipt of a notice of an essential patent claim, IAPMO will coordinate with the claimant to ensure collection of the assurance(s) required by IAPMOs adherence to the ANSI patent policy before the proposal that includes an essential patent claim is introduced into the code development process.
http://codes.iapmo.org/form_comments_upc_umc_2018.aspxhttp://www.ansi.org/essentialrequirements

INSTRUCTIONS FOR SUBMITTING COMMENTS

PLEASE READ CAREFULLY

1. Check the appropriate box to indicate whether this comment recommends adding new text, revising existing text, or delete text without substitution (see examples below).

2. Enter the appropriate comment on proposal item number that the proposed text applies to. 3. In the space identified as Proposed Text indicate the exact wording you propose as new or revised text or

the text you propose to be deleted. 4. In the space titled, Statement of Problem and Substantiation/Resolution, state the problem that will be

resolved by your recommendation and give the specific reason for your comment. 5. Where referencing a standard in your comment, such standard needs to be submitted in accordance with

the Guidelines for Referencing Mandatory Standards. Please provide two hard copies or one electronic copy with your comment. Please note that if the standard is not received by the closing date, your comment is considered incomplete and will not be processed.

6. Where additional supplementary materials such as tests, research papers, or other documents, need to be submitted, please provide supporting material electronically. Please note that if supporting material is not received by the closing date, it will not be accepted for review by the Technical Committee.

7. Check the box for copyright assignment. Please note if you are not the author of this comment (this text is copied from another source) please do not submit the proposed change. The author of the comment must give copyright assignment (which is the submitters own idea based on or as a result of research, experience and is not copied from another source).

Note: Content of Comments shall be in accordance with Section 4-4.5 of the IAPMO Regulations Governing Committee Projects of the UPC and UMC. Failure to comply with the above requirements will result in the comment not being processed. For further information on the standards process, please contact Code Development at 909-472-4110. For technical assistance, please call 909-230-5535 or 909-472-4111, or email [email protected].

Please support IAPMOs green initiative to remain paper free by providing the Proposed Monographs, Report on Proposals and Report on Comments in digital Adobe PDF. Note printed copies of the above referenced documents will not be available at the hearings. All requested printed copies will be mailed 30 days prior to the hearing date. In order to receive a printed copy, please submit your request by the due date on the form. http://www.iapmo.org/Pages/RequestFormforROPROC.aspx

Examples for applying charging statement for adding text, deleting text and revising text

Add new text as follows (applies only when adding a new section or all new text): Water Service. Piping from the water main or source of water supply to the water distribution piping of the building or premises served irrespective of the water meter location.

Revise text as follows (applies when revising an existing section by deleting text, adding text or both as follows): Building Supply. The pipe carrying potable water from the water meter or other source of water supply to the building or other point of use or distribution on the lot. Building supply shall also mean water service. Piping from the water main or source of water supply to the water distribution piping of the building or premises served irrespective of the water meter location.

Delete text without substitution (applies when deleting an entire section, table or both as follows): 302.0 Iron Pipe Size (IPS) Pipe. Iron, steel, brass and copper pipe shall be standard weight iron pipe size (IPS) pipe. 306.1 It shall be unlawful for any person to deposit, by any means whatsoever, into any plumbing fixture, floor drain, interceptor, sump, receptor, or device, which is connected to any drainage system, public sewer, private sewer, septic tank, or cesspool, any ashes; cinders; solids; rags; inflammable, poisonous, or explosive liquids or gas; oils; grease; or any other thing whatsoever that would, or could, cause damage to the drainage system or public sewer.
mailto:[email protected]://www.iapmo.org/Pages/RequestFormforROPROC.aspx

of 2

Assembly Consideration Session Rules Adopted by the IAPMO Board of Directors on July 9, 2007 and approved by the Standards Council on June 19, 2007.

The Assembly Consideration Session is an important step in developing a complete record to assist the Standards Council in determining the degree of consensus achieved. These Rules, or any part of same, may not be suspended. The transaction of business at the Assembly Consideration Session shall be governed, in order of precedence, first by the Regulations Governing Committee Projects (see especially section 4-4.3.1.1), second by these Rules, and third by Roberts Rules of Order Revised.

1. Meetings. The Secretary of the Standards Council shall develop and publish in advance, an agenda for each Assembly Consideration Session. At the discretion of the Secretary, the meeting may take place in a single session or may be divided into more than one session. All items on the agenda scheduled for consideration at a session shall be completed before the adjournment of that session.

2. Adjournment. Adjournment of each session shall take place only upon completion of the

scheduled agenda. 3. Recess. A session may be recessed at any time at the discretion of the Chair. A motion to

recess shall be allowed at the discretion of the Chair. 4. Question of Privilege. Ruled on by the Chair. 5. Call for Orders of the Day. Any change to the published agenda is to be announced by the

Chair at the commencement of the session. 6. Lay on the Table. Not allowed. 7. Previous Question. Requires a two-thirds vote of those present. For informational purposes

prior to the vote, the Chair has the authority to ask if there is anyone who wishes to speak, who has not spoken, and who has something new to add. A successful motion of the previous question will close debate on the pending motion and bring it to an immediate vote.

8. Limit or Extend Debate. Each speaker is allowed ten minutes to present their arguments. 9. Postpone. Allowed. 10. Commit or Refer. Not allowed. 11. Motions.

See Regulations Governing Committee Projects at section 4-4.3.1.1 and 4-4.3.1.2.

12. Postpone Indefinitely. Not allowed. 13. Voting on Motions. Except as otherwise provided in these rules, the vote on motions shall

be taken by a show of hands. If the Chair is uncertain of the result of the vote, he or she can

of 2

order a counting of the vote. A successful main motion requires a majority vote of those present.

14. Point of Order. Allowed. 15. Appeal. Decisions of the Chair can be appealed except as otherwise prohibited by these

rules. The proper venue for appeal of these rules is by an appeal filed with the Standards Council.

16. Suspend Rules. Not allowed. 17. Division of Question. Allowable at the discretion of the Chair. 18. Division of Assembly. Not allowed. 19. Parliamentary Inquiry or Point of Information. Allowed. 20. Withdraw Motion. A motion can be withdrawn only by a majority vote of the members

assembled. 21. Take from the Table. Not allowed. 22. Visual Aids and Physical Simulations. Visual aids and physical simulations of any kind are

prohibited. Only verbal presentations are allowed. 23. Distribution of Materials. All materials distributed within the Association Technical

Meeting room shall have prior approval by the secretary of the Standards Council. Only IAPMO staff shall be permitted to distribute such materials.

24. Reconsider, Rescind, or Amend Something Previously Adopted. Applicable only within

the period of discussion of the specific document and prior to the final vote.

TABLE OF CONTENTS

i

Item # Code Section Page # 001 1701.1, Table 1701.1 1 002 1701.2, Table 1701.2 21 003 301.2.2 36 004 Chapter 1, Chapter 2, Chapter 3 38 005 101.3 42 006 102.5, 210.0 44 007 203.0, 205.0, 206.0, 207.0, 208.0, 224.0 45 008 203.0, 205.0, 209.0, 214.0, 215.0, 216.0, 218.0, 221.0, 225.0 46 009 203.0 49 010 210.0 50 011 210.0 51 012 218.0 53 013 222.0 54 014 301.2 55 015 301.2 57 016 301.2.1 59 017 301.2.3, 604.1, 611.3, Table 1701.1 61 018 301.2.4 63 019 301.2.4 64 020 301.2.4 65 021 301.3 66 022 301.5.6 67 023 309.4 68 023.01 Table 309.4 70 024 309.5 71 025 312.13 73 026 312.13 74 027 312.14 75 028 Table 313.3 76 029 Table 313.3 77 030 314.4, 314.4.1 78 031 314.4.1 80 032 317.1 81 033 319.1 82 034 401.2 83 035 401.2 84 036 402.4 85 037 402.6 87 038 402.9 89 039 402.9 90 040 403.2 91 041 403.3, Table 1701.1 92 042 403.3, Table 1701.1 93 043 404.0 404.2, 701.4 94 044 405.1 96 045 406.0 406.4 97 046 406.2 99 047 406.5 100 048 407.1, 408.1 101 049 407.2.1, 420.2 102 050 407.2.1, 407.2.2, 408.2 104 051 407.2.1, 407.2.2, 408.2 106 052 407.3, Table 1701.1 107 053 407.3 108 054 407.3 110 055 407.3 111

TABLE OF CONTENTS

ii

Item # Code Section Page # 056 407.4, L 603.3.5.2 112 057 407.4 113 058 407.6, 409.3 114 059 408.2 115 060 408.3 117 061 408.3 118 062 408.5 119 063 408.5 120 064 408.7.1, 408.7.2 121 065 409.4 122 066 409.6, 409.6.1, 410.3 123 067 409.7, Table 1701.1 125 068 411.2, 411.2.2 126 069 411.2, 411.2.2 127 070 411.2 - 411.2.2 129 071 411.2.3 131 072 411.4 132 073 412.1 133 074 412.1.1 135 075 412.1.1 136 076 413.2 137 077 413.3, 414.2 138 078 414.3 140 079 415.1 141 080 416.2 142 081 416.2 143 082 416.2 145 083 417.1 146 084 417.1 147 085 417.3 148 086 417.4 149 087 417.4 417.4.2, Table 1701.1 150 088 417.5 417.5.3, Table 1701.1 151 089 420.1 152 090 420.1 153 091 420.2 154 092 420.2 156 093 420.2 157 094 420.2 158 095 420.3 159 096 420.3 161 097 422.1, Table 422.1 162 098 422.0 422.4.1, Table 1701.1 165 099 422.2 422.2.2 167 099.01 422.2.1 170 100 423.0 423.8, Table 1701.1 171 101 424.0, 424.1, Table 1701.1 173 102 504.1, 504.3.2, 506.1.1, 506.2, 506.2.2 174 103 504.6 176 104 505.1, 505.4 177 105 505.2 178 106 505.2.1 179 107 507.4 180 108 506.4.1, 506.4.2, 506.5, 506.6, 506.8.2, 506.9 181 109 507.3, 507.3.1, 507.6, 507.10, 507.12, 507.13, 507.13.2, 507.14.2, 507.16 183 110 507.18, 507.21, 507.22, 507.27 185

TABLE OF CONTENTS

iii

Item # Code Section Page # 111 508.0, 508.1, 508.1.1, 508.2 508.3, 508.3.2, 508.4.4 187 112 509.1.1, 509.2 509.2.8, Table 1701.1 189 113 509.3.2, 509.3.3.1, 509.3.3.3, 509.3.6, 509.4.1, Table 509.4, Table 1701.1 192 114 509.5.1.1, 509.5.2, 509.5.3 194 115 509.5.4.1, 509.5.5, 509.5.6.1, 509.5.8 196 116 509.6 509.6.2, 509.6.2.2 509.6.3, 509.6.3.2 198 117 509.6.4, 509.6.5, 509.7.1, 509.7.2, 509.7.3, 509.7.3.5 201 118 509.8, 509.8.2, 509.8.3, 509.8.5, 509.10.1.2 202 119 509.10.1.3, 509.10.1.4, 509.10.2.1, 509.10.2.3, Table 509.10.1.3 509.10.3 203 120 509.10.5, 509.10.6, 509.11, 510.1.10 205 121 510.1.16, 510.2, 510.2.2, 510.2.6, 510.2.7 206 122 510.2.18 510.2.21, 510.2.25 208 123 601.2, 601.2.1 210 124 601.3 211 125 601.3 212 126 601.3.2 601.3.2.3 213 127 601.3.3 601.3.5 215 128 601.3.6 216 129 601.3.7 217 130 601.3.8 601.3.8.2 218 131 601.3.9 219 132 603.4.3 220 133 603.4.7, 603.5.12 221 134 603.5.21 222 135 603.5.16, 603.5.16.1 223 136 604.1 224 137 604.1 225 138 Table 604.1 226 139 Table 604.1 227 140 Table 604.1 228 141 Table 604.1 229 142 Table 604.1 231 143 Table 604.1, Table 1701.1 233 143.01 Table 604.1 234 143.02 Table 604.1 235 144 604.5 236 145 604.5, Table 1701.1 237 146 604.9 238 147 604.9, Table 1701.1 239 148 604.13 240 149 604.10.1 241 150 605.1.3.2 242 151 605.1, 605.1.3.2, 605.13, 605.13.1, 605.16, 605.16.1, 705.6 705.6.1, 218.0 243 152 605.1.1, 605.1.2, 605.1.3.3, 605.1.4, 605.1.5 245 153 605.2.1 247 154 605.2.1, 605.2.1.1 248 155 605.2.2 249 156 605.2.3 251 156.01 605.2.2, 605.3.1, 605.12.2, 705.1.2, 705.5.2, 705.8.4 252 157 605.3.1 254 158 605.3.2, 605.3.2.1 255 159 605.5.2, 605.6.1.1, 605.6.1.3 257 160 605.8, 605.8.1 259 161 605.8.1 260

TABLE OF CONTENTS

iv

Item # Code Section Page # 162 605.9.1, 605.10.1, 605.12.2 262 163 605.9.3 264 164 605.12 265 165 606.1 266 166 606.1 267 167 606.1, Table 1701.1 268 168 607.2, 607.5, 608.2, 608.7, 611.2 269 169 606.8 271 170 608.3 272 171 608.5 273 172 609.3 274 173 609.4 275 174 609.4 276 175 609.10 277 176 609.10 278 177 Table 610.3, Table 702.1, 210.0 279 178 610.9 280 179 610.9.1 281 180 611.3 283 181 611.3 284 182 612.1 285 183 612.1 286 184 701.2 701.2.4 287 185 701.2 289 186 701.2 291 187 701.2 293 188 701.2 294 189 Table 701.2, Table 1701.1 296 189.01 Table 701.2 298 190 Table 701.2 299 190.01 Table 701.2 301 190.02 Table 701.2 302 190.03 Table 604.1 303 191 Table 702.1 304 192 Table 702.1 306 193 705.1.1, 705.1.2, 705.2.2, 705.3.1, 705.3.3, 705.3.4, 705.4.2 705.5.1, 705.5.2, 705.6.2, 705.7.1, 705.9 308 194 705.5 - 705.5.1.3 311 195 706.2 312 196 707.1, Table 701.1 313 197 707.4 314 198 707.4.1 315 199 707.9 316 200 710.12 317 201 711.1 318 202 712.1, 712.3, 712.3.1, 723.1, 1106.2, 1106.2.2, 1106.2.2.1 319 203 714.5 321 204 715.3 322 205 715.3 323 206 804.2 324 207 811.2, Table 1701.1 325 208 814.3, Table 814.3 326 209 903.2.3 328 210 903.1 329 211 903.1, 1101.4 330 212 906.1 332 213 906.1.1 333

TABLE OF CONTENTS

v

Item # Code Section Page # 214 908.2.3 335 215 909.2 336 216 910.3 337 217 911.0 911.6, Table 1701.1 338 218 1002.2, Table 1002.2 340 219 1007.2 342 220 1014.1, 1014.3.4 343 221 Table 1014.2.1 345 222 1015.2 346 223 1015.4 347 224 1015.4 349 225 1101.4.2, 1101.4.3, 1101.4.6 350 225.01 Table 1101.4.6 352 226 1102.1 353 227 1102.1, Table 1701.1 354 228 1102.3 356 229 1103.0 1103.6, 1105.1, 1105.2, 1602.9.12, Table 1101.8, Table 1103.2, Table 1103.4 Table 1103.6 357 230 1103.2.1 362 231 1106.0 1106.2, Table 1701.1 363 232 1201.1, 1216.6 364 233 1202.1, 1202.2, 1202.3, Table 1701.1 365 234 1208.1, 1208.1.1, 1208.2, 1208.3.1 367 235 1208.4.1, Table 1208.4.1 368 236 1208.4.3, 1208.5, 1208.5.1.1, 1208.5.4, 1208.5.4.2.3 370 237 1208.5.4, 1208.5.4.1, 1208.5.8.1, 1208.5.8.2 371 238 1208.5.7.3, 1208.5.8, 1208.5.9.1, 1208.5.9.4, 1208.5.10 1208.5.10.6, Table 1701.1 373 239 1208.5.11 1208.5.11.5, 1208.6.1.1, 1208.6.1.2, 1208.6.4 375 240 1208.7.1 1208.9.4, 1209.1 376 241 1208.7.2, 1208.7.5 381 242 1210.1.1, 1210.1.3 1210.1.3.9 383 243 1210.1.5, 1210.1.7 1210.1.7.2 385 244 1210.1.7.1 387 245 1210.2, 1210.2.1, 1210.2.4, 1210.2.4.3, 1210.2.5 389 246 1210.4.1, 1210.4.3, 1210.5, 1210.5.1 391 247 1210.7.2, 1210.8.1, 1210.8.2 393 248 1210.9, 1210.11.3 394 249 1210.14 1210.14.6 396 250 1211.2 1211.2.5, Table 1701.1 399 251 1211.1, 1211.2 400 252 1211.6, 1212.10 402 253 1212.1 1212.1.2 404 254 1212.1, 1212.1.1 406 255 1212.2, 1212.3.1, 1212.3.2, 1212.4 408 256 1212.2, 1212.3.2 410 257 1212.4 1212.5 412 258 1212.6 414 259 1212.6 1212.9, Figure 1212.8 416 260 1212.7 419 261 1213.1, 1213.1.4, 1213.2.5, 1213.3 421 262 1213.4.1, 1213.6.1.4, 1213.6.2.2, 1214.0, 1214.2 423 263 1215.1 424 264 Table 1216.2(2), Table 1216.2(3) 425 265 1301.4, 1301.5, 1301.6, 1302.1 1302.3, 1304.3 1304.4 429 266 1306.1, 1307.1 1307.7 431 267 1308.2, 1308.5, 1308.6, Table 1701.1 432

TABLE OF CONTENTS

vi

Item # Code Section Page # 268 1309.2 1309.5.2 434 269 1309.3.6 1309.3.7.4 436 270 1309.3.8 1309.3.8.9 437 271 1309.3.9 1309.3.10.4 439 272 1309.4 1309.9 440 273 1310.0 1310.2.1, 1310.3 1310.3.3 441 274 1310.4.1, 1310.4.1.1, 1310.5 1310.5.4, Table 1310.5.4(1)-(2), 1310.6 1310.8.2, 1310.10 1310.11.2 442 275 1310.11.1 445 276 1311.1, 1311.2 446 277 1312.0 1312.1.3 447 278 1312.1.3 1312.4.1 448 279 1312.5 1312.9.1 449 280 1312.0 1312.9.2 451 281 1313.1 1313.1.2 452 282 1314.1.1, 1314.1.2.1 1314.2.2 453 283 1314.1.3 1314.1.3.2 454 284 1314.1.4 1314.2.2 455 285 1315.2 1315.5.4 456 286 1316.2, 1316.2.1, 1316.3 458 287 1317.1 1317.2.1, 1317.4 459 288 1318.1 1318.3 460 289 1318.2 1318.3 461 290 1319.4 1319.5.5 463 291 1319.6 1319.6.8 465 292 1319.7 1319.7.7 466 293 1319.8, 1319.8.3, 1319.8.6 1319.9.3, 1319.11 1319.12.2 Table 1319.11 467 294 1501.2 469 295 Chapter 15, Table 1701.1 470 296 1504.7 474 297 1504.7.1, Table 1701.1 475 298 Chapter 16 477 299 1602.1 480 300 1602.9.5.1 481 301 1602.9.5.1, Table 1701.1 482 302 Table 1701.1 483 303 Table 1701.1 484 304 Table 1701.1 486 305 Table 1701.1 487 306 Table 1701.1 492 307 Table 1701.1 493 308 Table 1701.1 495 309 Table 1701.1 496 310 Table 1701.1 497 311 Table 1701.1 498 312 Table 1701.1 499 313 Table 1701.1 500 314 Table 1701.1 501 315 Table 1701.1 502 316 Table 1701.1 503 317 Table 1701.1 504 318 Appendix C, Appendix E, Appendix F, Appendix L 506 319 Appendix A 511 320 C 601.0 C 601.9, Table C 601.2 515 321 Appendix G 517 322 H 501.11 521

TABLE OF CONTENTS

vii

Item # Code Section Page # 323 Appendix K, Table 1701.1 522 324 L 201.0, 205.0, 206.0, 207.0 525 325 L 303.2, L 303.4 L303.4.5, Table 1701.1 526 326 L 402.2.1, L 402.3.1 527 327 L 402.6 L 402.6.3.1, Table 1701.1 528 328 L 402.7, L 402.9, L 402.10, Table 1701.1 530 329 L 404.2 531 330 L 404.3 532 331 L 404.4 533 332 L 404.6 534 333 L 405.1, Table 1701.1 535 334 L 407.1 L 407.3, 206.0, Table L 407.1 536 335 L 408.1.1 538 336 L 410.2, L 410.3 539 337 L 411.1, L 411.2, L 411.3 L 411.4, Table 1701.1 540 338 L 411.5 L 411.7, L 411.10.3, Table 1701.1 542 339 L 411.13 L 411.14.2 543 340 L 413.1 L 413.4 544 341 L 501.0 L 506.1, Table L 501.5.1, Table L 504.2(1), Table L 504.2(2) 545 342 L 601.2 L 601.2.2, L 602.7 L 602.7.2 550 343 L 603.3.2 552 344 L 603.3.3, L 603.4.2.1, L 607.0 554 345 M 101.0 M 201.6 555 346 M 201.7 M 201.7.4.1.7, Table 1701.1 558 347 M 201.7.4.2 M 201.8.2, Table 1701.1 561 348 M 201.8.3 M 201.8.13, Table 1701.1 563 349 Appendix M 566 350 Appendix N 568

Task Group Report Standards Task Group Report

Technical Correlating Committee Report

2016 Uniform Plumbing Code Preprint

Copyright 2015 [or 2016 or 2017, etc.] by

International Association of Plumbing and Mechanical Officials All Rights Reserved

The standards listed in Table 1701.1 are referenced in various sections of this code and shall be considered part of the requirements of this document. The standards are listed herein by the standard number and effective date, the title, application and the section(s) of this code that references the standard. The application of the referenced standard(s) shall be as specified in Section 301.2.2. intended for use in the design, testing, and installation of materials, devices, appliances, and equipment regulated by this code. These standards are mandatory where required by sections in this code. The promulgating agency acronyms Organization abbreviations referred to in Table 1701.1 are defined in a list found at the end of the table.0

AHAM FWD-1-2009 Food Waste Disposers Appliances 301.2.2, 301.3 APSP 1-2003 Public Swimming Pools Swimming Pools,

Spas, and Hot Tubs 301.2.2, 301.3

ARCSA/ASPE 63-2013 Rainwater Catchment Systems Miscellaneous 1602.1, K 104.9.1, L 504.9.1

ASCE 25-2006 Earthquake-Actuated Automatic Gas Shutoff Devices Fuel Gas 301.2.2, 301.3 ASHRAE 90.1-2013 Energy Standard for Buildings Except Low-Rise

Residential Buildings Miscellaneous L 603.2.1, Table L

603.3.2 ASHRAE 90.2-2007 Energy-Efficient Design of Low-Rise Residential

Buildings Miscellaneous 301.2.2, 301.3

ASME A13.1-2007 (R2013)

Scheme for the Identification of Piping Systems Piping 301.2.2, 301.3

ASME A112.1.2-2012 Air Gaps in Plumbing Systems (For Plumbing Fixtures and Water-Connected Receptors)

Fittings Table 603.2

ASME A112.1.3-2000 (R2010) (R2015)

Air Gap Fittings for Use with Plumbing Fixtures, Appliances, and Appurtenances


ASME A112.3.1-2007 (R2012)

Stainless Steel Drainage Systems for Sanitary DWV, Storm, and Vacuum Applications, Above- and Below-Ground (Notes 1 and 7)

Piping, Ferrous 418.1, 705.6.2, Table 701.2, 1102.1

ASME A112.3.4-2013/CSA B45.9-2013

Plumbing Fixtures with Pumped Waste and Macerating Toilet Systems

Fixtures 710.13

ASME A112.4.1-2009 Water Heater Relief Valve Drain Tubes Appliances 301.2.2, 301.3 ASME A112.4.2-2009 Water Closet Personal Hygiene Devices Fixtures 301.2.2, 301.3 ASME A112.4.3-1999 (R2010)

Plastic Fittings for Connecting Water Closets to the Sanitary Drainage System

Fittings 301.2.2, 301.3

ASME A112.4.14-2004 (R2010)

Manually Operated, Quarter-Turn Shutoff Valves for Use in Plumbing Systems

Valves 606.1

ASME A112.6.1M-1997 (R2012)

Floor-Affixed Supports for Off-the-Floor Plumbing Fixtures for Public Use

Fixtures 301.2.2, 301.3

ASME A112.6.2-2000 (R2010)

Framing-Affixed Supports for Off-the-Floor Water Closets with Concealed Tanks

Fixtures 301.2.2, 301.3

1

ASME A112.6.3-2001 (R2007)

Floor and Trench Drains Fixtures DWV Components

418.1

ASME A112.6.4-2003 (R2012)

Roof, Deck, and Balcony Drains Fixtures DWV Components

1102.1

ASME A112.6.7-2010 (R2015)

Sanitary Floor Sinks Fixtures 421.1

ASME A112.6.9-2005 (R2010)

Siphonic Roof Drains DWV Components 301.2.2, 301.3

ASME A112.14.1-2003 (R2012)

Backwater Valves Valves 710.6

ASME A112.14.3-2000 (R2004) (R2014)

Grease Interceptors Fixtures 1014.1

ASME A112.14.4-2001 (R2012)

Grease Removal Devices Fixtures 1014.1

ASME A112.14.6-2010 (R2015)

FOG (Fats, Oils, and Greases) Disposal Systems Fixtures 1015.2, 1015.4

ASME A112.18.1-2012/CSA B125.1-2012

Plumbing Supply Fittings Fittings 402.9, 407.2.1, 407.2.2, 408.2, 408.3, 417.1, 417.2, 417.3, 417.4, 420.2, 420.3, 603.5.19, L 402.5.1, L 402.5.2.1, L 402.6, L 402.6.2, L 402.6.3

ASME A112.18.2-2011/CSA B125.2-2011

Plumbing Waste Fittings Fittings 301.2.2, 301.3

ASME A112.18.3-2002 (R2012)

Performance Requirements for Backflow Protection Devices and Systems in Plumbing Fixture Fittings

Backflow Protection

417.3, 417.4

ASME A112.18.6-2009/CSA B125.6-2009 (R2014)

Flexible Water Connectors Piping 604.5, 604.13

ASME A112.18.9-2011 Protectors/Insulators for Exposed Waste and Supplies on Accessible Fixtures

Miscellaneous 403.3

ASME A112.19.1-2013/CSA B45.2-2013

Enameled Cast Iron and Enameled Steel Plumbing Fixtures

Fixtures 407.1, 408.1, 409.1, 415.1, 420.1

ASME A112.19.2-2013/CSA B45.1-2013

Ceramic Plumbing Fixtures Fixtures 407.1, 408.1, 409.1, 410.1, 411.1, 411.2, 411.2.2, 412.1, 415.1, 420.1, L 402.2.1, L 402.2.2, L 402.3

ASME A112.19.3-2008/CSA B45.4-2008 (R2013)

Stainless Steel Plumbing Fixtures Fixtures 407.1, 408.1, 409.1, 410.1, 411.1, 415.1, 420.1, L 402.3.1

ASME A112.19.5-2011/CSA B45.15-2011

Flush Valves and Spuds for Water Closets, Urinals, and Tanks

Fixtures 413.3

ASME A112.19.7-2012/CSA B45.10-2012

Hydromassage Bathtub Systems Fixtures 409.1, 409.6, 413.3

ASME A112.19.10-2003 (R2008)

Dual Flush Devices for Water Closets Fixtures 301.2.2, 301.3

ASME A112.19.12-2006 (R2011)R2014

Wall Mounted, Pedestal Mounted, Adjustable, Elevating, Tilting, and Pivoting Lavatory, Sink, and Shampoo Bowl Carrier Systems and Drain Waste Systems

Fixtures 407.1, 420.1

ASME A112.19.14-2013 Six-Liter Water Closets Equipped with a Dual Flushing Device

Fixtures 411.2.1, L 402.2.1

ASME A112.19.15-2012 Bathtubs/Whirlpool Bathtubs with Pressure Sealed Doors

Fixtures 409.1

2

ASME A112.19.19-2006 (R2011)

Vitreous China Nonwater Urinals Fixtures 412.1, L 402.3.1

ASME A112.21.3M-1985 (R2007)

Hydrants for Utility and Maintenance Use (Note 1) Valves 301.2.2, 301.3

ASME A112.36.2M-1991 (R2012)

Cleanouts (Note 1) DWV Components 301.2.2, 301.3

ASME B1.20.1-2013 Pipe Threads, General Purpose, Inch Joints 605.1.5, 605.2.3, 605.5.2, 605.12.3, 705.1.3, 705.3.4, 705.4.2, 705.5.3, 1208.5.7, 1309.4.3(2)

ASME B1.20.3-1976 (R2013)

Dryseal Pipe Threads, (Inch) Joints 301.2.2, 301.3

ASME B16.1-2010 Gray Iron Pipe Flanges and Flanged Fittings: Classes 25, 125, and 250

Fittings 1208.5.10

ASME B16.3-2011 Malleable Iron Threaded Fittings: Classes 150 and 300 Fittings Table 604.1, Table 701.2

ASME B16.4-2011 Gray Iron Threaded Fittings: Classes 125 and 250 Fittings Table 604.1 ASME B16.5-2013 Pipe Flanges and Flanged Fittings: NPS 1/2 through

NPS 24 Metric/Inch Fittings 301.2.2, 301.3

ASME B16.12-2009 (R2014)

Cast Iron Threaded Drainage Fittings (Note 1) Fittings Table 701.2

ASME B16.15-2013 Cast Copper Alloy Threaded Fittings: Classes 125 and 250


ASME B16.18-2012 Cast Copper Alloy Solder Joint Pressure Fittings (Note 1)


ASME B16.20-2012 Metallic Gaskets For Pipe Flanges: Ring-Joint, Spiral-Wound, and Jacketed

Joints 1208.5.10

ASME B16.21-2011 Nonmetallic Flat Gaskets for Pipe Flanges Joints 301.2.2, 301.3 ASME B16.22-2013 Wrought Copper and Copper Alloy Solder-Joint

Pressure Fittings Fittings 1309.3, Table 604.1

ASME B16.23-2011 Cast Copper Alloy Solder Joint Drainage Fittings: DWV Fittings Table 701.2 ASME B16.24-2011 Cast Copper Alloy Pipe Flanges and Flanged Fittings:

Classes 150, 300, 600, 900, 1500, and 2500 Fittings 301.2.2, 301.3

ASME B16.26-2013 Cast Copper Alloy Fittings for Flared Copper Tubes Fittings Table 604.1, 1309.2 ASME B16.29-2012 Wrought Copper and Wrought Copper Alloy Solder-

Joint Drainage Fittings DWV (Note 1) Fittings Table 701.2

ASME B16.33-2012 Manually Operated Metallic Gas Valves for Use in Gas Piping Systems Up to 175 psi (Sizes NPS 12 through NPS 2)

Valves 301.2.2, 301.3

ASME B16.34-2013 Valves Flanged, Threaded, and Welding End Valves 606.1 ASME B16.39-2009 Malleable Iron Threaded Pipe Unions: Classes 150, 250

and 300 (Includes Revision Services) Fittings 301.2.2, 301.3

ASME B16.40-2013 Manually Operated Thermoplastic Gas Shutoffs and Valves in Gas Distribution Systems

Valves 301.2.2, 301.3

ASME B16.47-2011 Large Diameter Steel Flanges: NPS 26 through NPS 60 Metric/Inch

Fittings 301.2.2, 301.3

ASME B16.50-2013 Wrought Copper and Copper Alloy Braze-Joint Pressure Fittings

Fittings 1309.3, 1309.3.9

ASME B16.51-2013 Copper and Copper Alloy Press-Connect Pressure Fittings


ASME B31.1-2012 Power Piping Piping 301.2.2, 301.3 ASME B31.3-2012 Process Piping Piping F 1201.1 ASME B36.10M-2004 (R2010) 2015

Welded and Seamless Wrought Steel Pipe Fuel Gas, Piping, Ferrous

1208.5.2.1(1)

ASME B36.19-2004 (R2010)

Stainless Steel Pipe Piping, Ferrous 301.2.2, 301.3

ASME BPVC Section IV-2013

Rules for Construction of Heating Boilers Miscellaneous 301.2.2, 301.3

3

ASME BPVC Section VIII-2013 2015

Rules for Construction of Pressure Vessels Division 1 Miscellaneous 1314.2(2), 1315.4(2), E 413.6.2

ASME BPVC Section IX-2013 2015

Welding, Brazing, and Fusing Qualifications Qualification Standard for Welding, Brazing, and Fusing Procedures; Welders; Brazers; and Welding, Brazing, and Fusing Operators

Certification 225.0, 1307.1, 1309.5.1, 1309.5.2

ASSE 1001-2008 Atmospheric Type Vacuum Breakers Backflow Protection

Table 603.2

ASSE 1002/ASME A112.1002/CSA B125.12-20082015

Anti-Siphon Fill Valves for Water Closet Tanks Backflow Protection

413.3, Table 603.2

ASSE 1003-2009 Water Pressure Reducing Valves for Domestic Water Distribution Systems

Valves 301.2.2, 301.3

ASSE 1004-2008 Backflow Prevention Requirements for Commercial Dishwashing Machines

Backflow Protection

414.2

ASSE 1008-2006 Plumbing Aspects of Residential Food Waste Disposer Units

Appliances 419.1

ASSE 1010-2004 Water Hammer Arresters Appliances Water Supply Component

609.10

ASSE 1011-2004 Hose Connection Vacuum Breakers Backflow Protection

Table 603.2

ASSE 1012-2009 Backflow Preventers with an Intermediate Atmospheric Vent

Backflow Protection

301.2.2, 301.3

ASSE 1013-2011 Reduced Pressure Principle Backflow Preventers and Reduced Pressure Principle Fire Protection Backflow Preventers

Backflow Protection

Table 603.2

ASSE 1014-2005 Backflow Prevention Devices for Hand-Held Shower Backflow Protection

417.3

ASSE 1015-2011 Double Check Backflow Prevention Assemblies and Double Check Fire Protection Backflow Prevention Assemblies

Backflow Protection

Table 603.2

ASSE 1016-2011/ASME A112.1016-2011/CSA B125.16-2011

Automatic Compensating Valves for Individual Showers and Tub/Shower Combinations

Valves 408.3, L 402.6.3

ASSE 1017-2009 Temperature Actuated Mixing Valves for Hot Water Distribution Systems

Valves 301.2.2, 301.3

ASSE 1018-2001 Trap Seal Primer Valves - Potable Water Supplied Valves 301.2.2, 301.3 ASSE 1019-2011 Wall Hydrant with Backflow Protection and Freeze

Resistance Backflow Protection

Table 603.2

ASSE 1020-2004 Pressure Vacuum Breaker Assembly Backflow Protection

Table 603.2

ASSE 1022-2003 Backflow Preventer for Beverage Dispensing Equipment

Backflow Protection

603.5.12, Table 603.2

ASSE 1023-1979 Hot Water Dispensers Household Storage Type - Electrical

Appliances 301.2.2, 301.3

ASSE 1024-2004 Dual Check Backflow Preventers Backflow Protection

301.2.2, 301.3

ASSE 1032-2004 (R2011) Dual Check Valve Type Backflow Preventers for Carbonated Beverage Dispensers, Post Mix Type

Backflow Protection

301.2.2, 301.3

ASSE 1035-2008 Laboratory Faucet Backflow Preventers Backflow Protection

301.2.2, 301.3

ASSE 1037-19902015/ASME A112.1037-2015/CSA B125.37-2015

Pressurized Flushing Devices (Flushometers) for Plumbing Fixtures

Backflow Protection

413.2

ASSE 1044-2001 Trap Seal Primer Devices - Drainage Types and Electronic Design Types

DWV Components 301.2.2, 301.3

4

ASSE 1047-2011 Reduced Pressure Detector Fire Protection Backflow Prevention Assemblies

Backflow Protection

Table 603.2

ASSE 1048-2011 Double Check Detector Fire Protection Backflow Prevention Assemblies

Backflow Protection

Table 603.2

ASSE 1052-2004 Hose Connection Backflow Preventers Backflow Protection

Table 603.2

ASSE 1053-2004 Dual Check Backflow Preventer Wall Hydrants Freeze Resistant Type

Backflow Protection

Table 603.2

ASSE 1055-2009 Chemical Dispensing Systems Backflow Protection

301.2.2, 301.3

ASSE 1056-2013 Spill Resistant Vacuum Breaker Assemblies Backflow Protection

Table 603.2

ASSE 1057-2012 Freeze Resistant Sanitary Yard Hydrants with Backflow Protection

Backflow Protection

Table 603.2

ASSE 1060-2006 Outdoor Enclosures for Fluid Conveying Components Miscellaneous 603.4.7 ASSE 1061-2011 2015 Push-Fit Fittings Fittings 605.1.3.3, 605.2.1,

Table 604.1 ASSE 1062-2006 Temperature Actuated, Flow, Reduction (TAFR) Valves

for Individual Fixture Fittings Valves 301.2.2, 301.3

ASSE 1066-1997 Individual Pressure Balancing In-Line Valves for Individual Fixture Fittings (Note 6)

Valves 301.2.2, 301.3

ASSE 1069-2005 Automatic Temperature Control Mixing Valves Valves 408.3 ASSE 1070-2004 Water Temperature Limiting Devices Valves 407.3, 409.4, 410.3 ASSE 1071-2012 Temperature Actuated Mixing Valves for Plumbed

Emergency Equipment Valves 301.2.2, 301.3

ASSE 1079-2012 Dielectric Pipe Unions Fittings Joints

605.15, 605.16.1, 605.16.3

ASSE Series 5000-2009 2015

Cross-Connection Control Professional Qualifications Standard

Certification 603.2

ASSE Series 6000-2012 2015

Professional Qualifications Standard for Medical Gas Systems Personnel

Certification 1306.1, 1319.12.2

ASSE Series 7000-2013 Residential Potable Water Fire Protection System Installers & Inspectors for One and Two Family Dwellings

Miscellaneous 612.1

ASTM A47/A47M-1999 (R2009)

Ferritic Malleable Iron Castings Piping, Ferrous 301.2.2, 301.3

ASTM A48/A48M-2003 (R2012)

Gray Iron Castings Piping, Ferrous 301.2.2, 301.3

ASTM A53/A53M-2012 Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless

Piping, Ferrous Table 604.1, Table 701.2, 1208.5.2.1(2)

ASTM A74-2013a2015 Cast Iron Soil Pipe and Fittings (Notes 1 and 7) Piping, Ferrous Table 701.2 ASTM A106/A106M-20132015

Seamless Carbon Steel Pipe for High-Temperature Service

Piping, Ferrous 1208.5.2.1(3)

ASTM A126-2004 (R2009) Gray Iron Castings for Valves, Flanges, and Pipe Fittings

Piping, Ferrous 301.2.2, 301.3

ASTM A197/A197M-2000 (R2011)

Cupola Malleable Iron Piping, Ferrous 301.2.2, 301.3

ASTM A254/A254M-2012 Copper-Brazed Steel Tubing Piping, Ferrous 1208.5.3.1, E 409.1 ASTM A269/A269M-20132015

Seamless and Welded Austenitic Stainless Steel Tubing for General Service

Piping, Ferrous F 801.2, Table 604.1

ASTM A312/A312M-20132015b

Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes

Piping, Ferrous Table 604.1

ASTM A377-2003 (R2008)e1

Ductile-Iron Pressure Pipe Piping, Ferrous 301.2.2, 301.3

ASTM A479/A479M-2013b

Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels

Piping, Ferrous F 801.3

ASTM A518/A518M-1999 (R2012)

Corrosion-Resistant High-Silicon Iron Castings Piping, Ferrous 301.2.2, 301.3

ASTM A536-1984 (R2009) Ductile Iron Castings Piping, Ferrous 301.2.2, 301.3

5

ASTM A653/A653M-2013 Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process


ASTM A733-2013 Welded and Seamless Carbon Steel and Austenitic Stainless Steel Pipe Nipples


ASTM A861-2004 (R2013) High-Silicon Iron Pipe and Fittings (Note 1) Piping, Ferrous 811.2 ASTM A888-2013a2015 Hubless Cast Iron Soil Pipe and Fittings for Sanitary

and Storm Drain, Waste, and Vent Piping Applications (Note 7)

Piping, Ferrous Table 701.2

ASTM A1045-2010 Flexible Poly (Vinyl Chloride) (PVC) Gaskets used in Connection of Vitreous China Plumbing Fixtures to Sanitary Drainage Systems

Piping, Plastic 301.2.2, 301.3

ASTM A1056-2012 Cast Iron Couplings used for Joining Hubless Cast Iron Soil Pipe and Fittings

Fittings Piping, Ferrous

705.2.2

ASTM B29-2003 (R2009) Refined Lead Joints 301.2.2, 301.3 ASTM B32-2008 (R2014) Solder Metal (Note 2) Joints 605.1.4, 705.3.3,

1309.2 ASTM B42-20102015a Seamless Copper Pipe, Standard Sizes Piping, Copper

Alloy Table 604.1

ASTM B43-20092015 Seamless Red Brass Pipe, Standard Sizes Piping, Copper Alloy

Table 604.1, Table 701.2

ASTM B75/B75M-2011 Seamless Copper Tube (Note 7) Piping, Copper Alloy


ASTM B88-20092014 Seamless Copper Water Tube Piping, Copper Alloy

604.4, Table 604.1, 903.2.3, 1208.5.3.2, 1308.5(1)(a), E 409.1,

ASTM B135-2010 Seamless Brass Tube Piping, Copper Alloy

Table 604.1

ASTM B152/B152M-2013 Copper Sheet, Strip, Plate, and Rolled Bar Miscellaneous 408.7.4 ASTM B187/B187M-2011 Copper, Bus Bar, Rod, and Shapes and General Purpose

Rod, Bar, and Shapes Miscellaneous 301.2.2, 301.3

ASTM B210-2012 Aluminum and Aluminum-Alloy Drawn Seamless Tubes

Piping, Ferrous 1208.5.3.3

ASTM B241/B241M-2012e1

Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube

Piping, Ferrous 1208.5.2.3, 1208.5.3.3

ASTM B251-2010 General Requirements for Wrought Seamless Copper and Copper-Alloy Tube (Note 7)

Piping, Copper Alloy


ASTM B280-2013 Seamless Copper Tube for Air Conditioning and Refrigeration Field Service


1208.5.3.2, 1308.5(1)(b), E 409.1

ASTM B302-2012 Threadless Copper Pipe, Standard Sizes (Note 7) Piping, Copper Alloy


ASTM B306-2013 Copper Drainage Tube (DWV) (Note 7) Piping, Copper Alloy

Table 701.2, 903.2.3

ASTM B370-2012 Copper Sheet and Strip for Building Construction Miscellaneous 301.2.2, 301.3 ASTM B447-2012a Welded Copper Tube Piping, Copper

Alloy Table 604.1

ASTM B584-2013 Copper Alloy Sand Castings for General Applications (Note 3)


301.2.2, 301.3

ASTM B587-2012 Welded Brass Tube Piping, Copper Alloy

301.2.2, 301.3

ASTM B687-1999 (R2011) Brass, Copper, and Chromium-Plated Pipe Nipples Piping, Copper Alloy

301.2.2, 301.3

ASTM B813-2010 Liquid and Paste Fluxes for Soldering of Copper and Copper Alloy Tube

Joints 605.1.4, 705.3.3

ASTM B819-2000 (R2011) Seamless Copper Tube for Medical Gas Systems Piping, Copper Alloy

1308.4, 1308.5(1)(c)

ASTM B828-2002 (R2010) Making Capillary Joints by Soldering of Copper and Copper Alloy Tube and Fittings

Joints 605.1.4, 705.3.3, 1309.2

6

ASTM C4-2004 (R2009R2014)

Clay Drain Tile and Perforated Clay Drain Tile Piping, Non-Metallic

Table 1101.4.6

ASTM C14-2011 Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe (Note 7)

Piping, Non-Metallic

301.2.2, 301.3

ASTM C412-2011 Concrete Drain Tile Piping, Non-Metallic

301.2.2, 301.3

ASTM C425-2004 (R2013) Compression Joints for Vitrified Clay Pipe and Fittings Joints 705.7.1 ASTM C443-2012 Joints for Concrete Pipe and Manholes, Using Rubber

Gaskets Joints 301.2.2, 301.3

ASTM C444-2003 (R2009) Perforated Concrete Pipe Piping, Non-Metallic

301.2.2, 301.3

ASTM C478-2013 Precast Reinforced Concrete Manhole Sections Miscellaneous 301.2.2, 301.3 ASTM C564-20122014 Rubber Gaskets for Cast Iron Soil Pipe and Fittings Joints 705.2.2 ASTM C700-2013 Vitrified Clay Pipe, Extra Strength, Standard Strength,

and Perforated (Note 7) Piping, Non-Metallic

Table 701.2, Table 1101.4.6

ASTM C1053-2000 (R2010)

Borosilicate Glass Pipe and Fittings for Drain, Waste, and Vent (DWV) Applications (Note 1)

Piping, Non-Metallic

811.2

ASTM C1173-2010e1(R2014)

Flexible Transition Couplings for Underground Piping Systems

Fittings Joints

705.9

ASTM C1227-2013 Precast Concrete Septic Tanks DWV Components 301.2.2, 301.3 ASTM C1277-20122015 Shielded Couplings Joining Hubless Cast Iron Soil Pipe

and Fittings DWV Components Fixtures

301.2.4, 705.2.2

ASTM C1440-2008 (R2013)e1

Thermoplastic Elastomeric (TPE) Gasket Materials for Drain, Waste, and Vent (DWV), Sewer, Sanitary and Storm Plumbing Systems

Joints 301.2.2, 301.3

ASTM C1460-2012 Shielded Transition Couplings for Use With Dissimilar DWV Pipe and Fittings Above Ground

Joints 705.9

ASTM C1461-2008 (R2013)

Mechanical Couplings Using Thermoplastic Elastomeric (TPE) Gaskets for Joining Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems for Above and Below Ground Use

Joints 705.9

ASTM C1540-20112015 Heavy Duty Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings

Joints 705.2.2

ASTM C1563-20042008(R2013)

Gaskets for Use in Connection with Hub &and Spigot Cast Iron Soil Pipe and Fittings for Sanitary Drain, Waste, Vent, and Storm Piping Applications

Joints 705.2.2

ASTM D1784-2011 Rigid Poly (Vinyl Chloride) (PVC) Compounds and Chlorinated Poly (Vinyl Chloride) (CPVC) Compounds


ASTM D1785-20122015 Poly (Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 (Note 7)

Piping, Plastic Table 604.1, Table 701.2, 1308.5

ASTM D2235-2004 (R2011)

Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings

Joints 705.1.2

ASTM D2239-2012a Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter

Piping, Plastic Table 604.1

ASTM D2241-20092015 Poly (Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series)


ASTM D2321-2011 Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications (Note 7)


ASTM D2464-20132015 Threaded Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 (Note 1)


ASTM D2466-20132015 Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 (Note 1)

Fittings Table 604.1, 1309.2

ASTM D2467-2013a2015

Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 (Note 1)


ASTM D2513-20132014e1

Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings (Note 1)

Piping, Plastic 1208.5.4, 1208.5.4.2.2, 1208.5.9.2, 1210.1.7.1(1), E 409.3

7

ASTM D2517-2006 (R2011)

Reinforced Epoxy Resin Gas Pressure Pipe and Fittings Piping, Plastic E 409.3

ASTM D2564-2012 Solvent Cements for Poly (Vinyl Chloride) (PVC) Plastic Piping Systems

Joints 605.12.2, 705.5.2

ASTM D2609-2002 (R2008)2015

Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe (Note 1)


ASTM D2657-2007 Heat Fusion Joining of Polyolefin Pipe and Fittings (Note 1)

Joints 301.2.2, 301.3

ASTM D2661-20112014 Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings (Notes 1 and 7)


ASTM D2665-20122014 Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings (Note 7)


ASTM D2672-1996a (R2009)2014

Joints for IPS PVC Pipe Using Solvent Cement Joints 1309.2

ASTM D2680-2001 (R2009R2014)

Acrylonitrile-Butadiene-Styrene (ABS) and Poly (Vinyl Chloride) (PVC) Composite Sewer Piping (Note 7)


ASTM D2683-2010e1 2014

Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing


ASTM D2729-2011 Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings (Notes 1 and 7)

Piping, Plastic Table 1101.4.6

ASTM D2737-2012a Polyethylene (PE) Plastic Tubing Piping, Plastic Table 604.1 ASTM D2751-2005 Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and

Fittings (Notes 1 and 7) Piping, Plastic 301.2.2, 301.3

ASTM D2774-2012 Underground Installation of Thermoplastic Pressure Piping


ASTM D2846/D2846M-2009be12014

Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Hot- and Cold-Water Distribution Systems

Piping, Plastic 605.2.2, 605.3.1, Table 604.1, 1308.5, 1309.2

ASTM D2855-1996 (R2010)

Making Solvent-Cemented Joints with Poly (Vinyl Chloride) (PVC) Pipe and Fittings

Joints 301.2.2, 301.3

ASTM D2996-2001 (R2007)e1

Filament-Wound Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe


ASTM D3034-2008 Type PSM Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings (Note 7)


ASTM D3035-2012e22015

Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter


ASTM D3122-1995 (R2009)

Solvent Cements for Styrene-Rubber (SR) Plastic Pipe and Fittings

Joints 301.2.2, 301.3

ASTM D3138-2004 (R2011)

Solvent Cements for Transition Joints Between Acrylonitrile-Butadiene-Styrene (ABS) and Poly (Vinyl Chloride) (PVC) Non-Pressure Piping Components

Joints 705.8.4

ASTM D3139-1998 (R2011)

Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals

Joints 605.12.1

ASTM D3212-2007 (R2013)

Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals

Joints 705.1.1, 705.5.1

ASTM D3261-2012e1 Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing


ASTM D3311-2011 Drain, Waste, and Vent (DWV) Plastic Fittings Patterns (Note 1)

Fittings 301.2.2, 301.3

ASTM D3965-2011 Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings


ASTM D4068-20092015 Chlorinated Polyethylene (CPE) Sheeting for Concealed Water-Containment Membrane

Miscellaneous 408.7.2

ASTM D4101-2011 Polypropylene Injection and Extrusion Materials Miscellaneous 301.2.2, 301.3 ASTM D4551-2012 Poly (Vinyl Chloride) (PVC) Plastic Flexible Concealed

Water-Containment Membrane Miscellaneous 408.7.1

ASTM D6104-1997 (R2011)

Determining the Performance of Oil/Water Separators Subjected to Surface Run-Off

Miscellaneous 301.2.2, 301.3

8

ASTM E84-20132015a Surface Burning Characteristics of Building Materials Miscellaneous 701.2(2), 903.1(2), 1101.4

ASTM E119-2012a2015 Fire Tests of Building Construction and Materials Miscellaneous 1404.3, 1405.3 ASTM E814-2013a Fire Tests of Penetration Firestop Systems Miscellaneous 208.0, 222.0,

1404.3, 1405.3 ASTM F402-2005 (R2012)

Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings

Joints 301.2.2, 301.3

ASTM F405-2013 Corrugated Polyethylene (PE) Pipe and Fittings Piping, Plastic Table 1101.4.6 ASTM F409-2012 Thermoplastic Accessible and Replaceable Plastic Tube

and Tubular Fittings (Note 1) Piping, Plastic 301.2.2, 301.3

ASTM F437-20092015 Threaded Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80


ASTM F438-20092015 Socket-Type Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40


ASTM F439-2013 Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80


ASTM F441/F441M-2013e12015

Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80

Piping, Plastic Table 604.1, 1308.5

ASTM F442/F442M-2013e1

Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe (SDR-PR)

Piping, Plastic 605.2.2, Table 604.1

ASTM F446-1985 (R2009) Grab Bars and Accessories Installed in the Bathing Area Miscellaneous 301.2.2, 301.3 ASTM F480-2012 Thermoplastic Well Casing Pipe and Couplings Made in

Standard Dimension Ratios (SDR), SCH 40 and SCH 80 Piping, Plastic 301.2.2, 301.3

ASTM F493-20102014 Solvent Cements for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe and Fittings

Joints 605.2.2, 605.3.1, 1309.2

ASTM F628-2012e1 Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe with a Cellular Core (Notes 1 and 7)


ASTM F656-20102015 Primers for Use in Solvent Cement Joints of Poly (Vinyl Chloride) (PVC) Plastic Pipe and Fittings

Joints 605.2.2, 605.3.1, 605.12.2, 705.5.2

ASTM F667-2012 3 through 24 in. Corrugated Polyethylene Pipe and Fittings


ASTM F714-2013 Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter


ASTM F794-2003 (R2009R2014)

Poly (Vinyl Chloride) (PVC) Profile Gravity Sewer Pipe and Fittings Based on Controlled Inside Diameter (Note 7)


ASTM F810-2012 Smoothwall Polyethylene (PE) Pipe for Use in Drainage and Waste Disposal Absorption Fields


ASTM F876-20132015a Crosslinked Polyethylene (PEX) Tubing Piping, Plastic 605.9.1, Table 604.1

ASTM F877-2011a Crosslinked Polyethylene (PEX) Hot- and Cold-Water Distribution Systems


ASTM F891-2010 Coextruded Poly (Vinyl Chloride) (PVC) Plastic Pipe with a Cellular Core (Note 7)


ASTM F894-2013 Polyethylene (PE) Large Diameter Profile Wall Sewer and Drain Pipe (Note 7)


ASTM F949-2010 Poly (Vinyl Chloride) (PVC) Corrugated Sewer Pipe with a Smooth Interior and Fittings (Note 7)


ASTM F1055-2013 Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing


ASTM F1216-2009 Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube

Piping, Plastic 715.3

ASTM F1281-2011 Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Pressure Pipe


ASTM F1282-2010 Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe


9

ASTM F1336-2007 Poly (Vinyl Chloride) (PVC) Gasketed Sewer Fittings Fittings 301.2.2, 301.3 ASTM F1412-2009 Polyolefin Pipe and Fittings for Corrosive Waste

Drainage Systems Piping, Plastic 811.2

ASTM F1476-2007 (R2013)

Performance of Gasketed Mechanical Couplings for Use in Piping Applications

Joints 301.2.2, 301.3

ASTM F1488-2009e12014

Coextruded Composite Pipe (Note 7) Piping, Plastic Table 701.2

ASTM F1499-2012

Coextruded Composite Drain, Waste, and Vent Pipe (DWV)


ASTM F1673-2010 Polyvinylidene Fluoride (PVDF) Corrosive Waste Drainage Systems


ASTM F1743-2008 Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)


ASTM F1807-2013a2015

Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing


ASTM F1866-20072013 Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings


ASTM F1924-2012 Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing

Fittings 301.2.2, 301.3

ASTM F1948-2012 Metallic Mechanical Fittings for Use on Outside Diameter Controlled Thermoplastic Gas Distribution Pipe and Tubing

Fittings 301.2.2, 301.3

ASTM F1960-20122015 Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) Tubing


ASTM F1961-2009 Metal Mechanical Cold Flare Compression Fittings with Disc Spring for Crosslinked Polyethylene (PEX) Tubing


ASTM F1970-2012e1 Special Engineered Fittings, Appurtenances or Valves for Use in Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Systems

Piping, Plastic 606.1, Table 604.1

ASTM F1973-2013e1 Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems

Fuel Gas 1210.1.7.1(2)

ASTM F1974-2009 (R2015)

Metal Insert Fittings for Polyethylene/ Aluminum/Polyethylene and Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Composite Pressure Pipe

Fittings 605.7.1, 605.10.1, Table 604.1

ASTM F1986-2001 (R2011)

Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hot and Cold Drinking-Water Systems

Fittings 301.2.2, 301.3

ASTM F2080-20122015 Cold-Expansion Fittings with Metal Compression-Sleeves for Cross-linked Polyethylene (PEX) Pipe


ASTM F2098-2008 Stainless Steel Clamps for Securing SDR9 Cross-linked Polyethylene (PEX) Tubing to Metal Insert and Plastic Insert Fittings

Fittings Joints

Table 604.1

ASTM F2159-20112014 Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

Fittings Joints

Table 604.1

ASTM F2165-2013 Flexible Pre-Insulated Piping Piping, Plastic 301.2.2, 301.3 ASTM F2206-2011 Fabricated Fittings of Butt-Fused Polyethylene (PE)

Plastic Pipe, Fittings, Sheet Stock, Plate Stock, or Block Stock


ASTM F2262-2009 Crosslinked Polyethylene/Aluminum/ Crosslinked Polyethylene Tubing OD Controlled SDR9


10

ASTM F2306/F2306M-2013

Specification for 12 to 60 in. [300 to 1500 mm] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Gravity-Flow Storm Sewer and Subsurface Drainage Applications


ASTM F2389-20102015 Pressure-Rated Polypropylene (PP) Piping Systems Piping, Plastic 605.11.1, 606.1, Table 604.1

ASTM F2434-20092014 Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PEX-AL-PEX) Tubing

Fittings 605.10.1, Table 604.1

ASTM F2509-2012 Field-Assembled Anodeless Riser Kits for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing

Fuel Gas 1210.1.7.1(3)

ASTM F2620-20122013 Heat Fusion Joining of Polyethylene Pipe and Fittings Joints 605.6.1.1, 605.6.1.3 ASTM F2735-2009 Plastic Insert Fittings for SDR9 Cross-linked

Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing


ASTM F2769-20102014 Polyethylene of Raised Temperature (PE-RT) Plastic Hot and Cold-Water Tubing and Distribution Systems

Piping, and Fittings, Plastic

Table 604.1

ASTM F2831-2012 Internal Non Structural Epoxy Barrier Coating Material Used in Rehabilitation of Metallic Pressurized Piping Systems

Miscellaneous 320.1

ASTM F2855-2012 Chlorinated Poly (Vinyl Chloride)/Aluminum/Chlorinated Poly (Vinyl Chloride) (CPVC/AL/CPVC) Composite Pressure Tubing


AWS A5.8-2011 Filler Metals for Brazing and Braze Welding Joints 605.1.1, 705.3.1, 1309.3.2

AWS A5.9-2012 Bare Stainless Steel Welding Electrodes and Rods Joints 605.13.2 AWS B2.2-2010 Brazing Procedure and Performance Qualification Certification 1307.1 AWS B2.4-2012 Welding Procedure and Performance Qualification for

Thermoplastics Joints, Certification 301.2.2, 301.3

AWWA C110-2012 Ductile-Iron and Gray-Iron Fittings Fittings Table 604.1 AWWA C111-2012 Rubber-Gasket Joints for Ductile-Iron Pressure Pipe and

Fittings Joints 605.4.1, 605.4.2

AWWA C151-2009 Ductile-Iron Pipe, Centrifugally Cast Piping, Ferrous Table 604.1 AWWA C153-2011 Ductile-Iron Compact Fittings Fittings Table 604.1 AWWA C203-2008 Coal-Tar Protective Coatings and Linings for Steel

Water Pipelines - Enamel and Tape Hot Applied Miscellaneous 301.2.2, 301.3

AWWA C210-2007 Liquid-Epoxy Coating Systems for the Interior and Exterior of Steel Water Pipelines

Miscellaneous 604.9

AWWA C213-2007 Fusion-Bonded Epoxy Coating for the Interior and Exterior of Steel Water Pipelines


AWWA C215-2010 Extruded Polyolefin Coatings for the Exterior of Steel Water Pipelines


AWWA C500-2009 Metal-Seated Gate Valves for Water Supply Service Valves 606.1 AWWA C504-2010 Rubber Seated Butterfly Valves, 3 in. (75 mm) through

72 in. (1800 mm) Valves 606.1

AWWA C507-2011 2015

Ball Valves, 6 in. through 60 in. (150 mm through 1,500 mm)

Valves 606.1

AWWA C510-2007 Double Check Valve Backflow Prevention Assembly Backflow Protection

Table 603.2

AWWA C511-2007 Reduced-Pressure Principle Backflow Prevention Assembly

Backflow Protection

Table 603.2

AWWA C606-2011 Grooved and Shouldered Joints Joints 301.2.2, 301.3 AWWA C900-2007 Polyvinyl Chloride (PVC) Pressure Pipe and Fabricated

Fittings, 4 in. through 12 in. (100 mm through 300 mm), for Water Transmission and Distribution


AWWA C901-2008 Polyethylene (PE) Pressure Pipe and Tubing, 1/2 in. (13 mm) through 3 in. (76 mm), for Water Service


11

AWWA C904-2006 Cross-Linked Polyethylene (PEX) Pressure Pipe, 1/2 in. (12 mm) through 3 in. (76 mm), for Water Service


AWWA C907-2012 Injection-Molded Polyvinyl Chloride (PVC) Pressure Fittings, 4 in. through 12 in. (100 mm through 300 mm), for Water, Wastewater, and Reclaimed Water Service

Fittings 301.2.2, 301.3

CGA C-9-2013 Standard Color Marking of Compressed Gas Containers for Medical Use


CGA G-4.1-2009 Cleaning Equipment for Oxygen Service Miscellaneous 1308.2, 1311.1 CGA S-1.3-2008 Pressure Relief Device Standards-Part 3-Stationary

Storage Containers for Compressed Gases Fuel Gas F 501.8

CGA V-1-2013 Compressed Gas Cylinder Valve Outlet and Inlet Connections

Valves F 601.6, F 701.4

CISPI 301-2012 Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications (Notes 1 and 7)

Piping, Ferrous

Table 701.2

CISPI 310-2012 Couplings for Use in Connection with Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications

Joints 301.2.4, 705.2.2

CSA A257-2009 Concrete Pipe and Manhole Sections Piping 301.2.2, 301.3 CSA B45.0-2002 (R2008) General Requirements for Plumbing Fixtures Fixtures 301.2.2, 301.3 CSA B45.5-2011/IAPMO Z124-2011

Plastic Plumbing Fixtures Fixtures 407.1, 408.1, 409.1, 411.1, 412.1, 420.1, L 402.3, L 402.3.1

CSA B45.8-2013/IAPMO Z403-2013

Terrazzo, Concrete, and Natural Stone Plumbing Fixtures

Fixtures 301.2.2, 301.3

CSA B45.11-2011/IAPMO Z401-2011

Glass Plumbing Fixtures Fixtures 407.1

CSA B45.12-2013/IAPMO Z402-2013

Aluminum and Copper Plumbing Fixtures Fixtures 301.2.2, 301.3

CSA B64-2011 Backflow Preventers and Vacuum Breakers Backflow Protection

301.2.2, 301.3

CSA B64.1.1-2011 Atmospheric Vacuum Breakers (AVB) Backflow Protection

Table 603.2

CSA B64.1.2-2011 Pressure Vacuum Breakers (PVB) Backflow Protection

Table 603.2

CSA B64.2-2011 Hose Connection Vacuum Breakers (HCVB) Backflow Protection

301.2.2, 301.3

CSA B64.2.1.1-2011 Hose Connection Dual Check Vacuum Breakers (HCDVB)

Backflow Protection

Table 603.2

CSA B64.4-2011 Reduced Pressure Principle (RP) Backflow Preventers Backflow Protection

Table 603.2

CSA B64.4.1-2011 Reduced Pressure Principle Backflow Preventers for Fire Protection Systems (RPF)

Backflow Protection

Table 603.2

CSA B64.5-2011 Double Check Valve (DVCA) Backflow Preventers Backflow Protection

Table 603.2

CSA B64.5.1-2011 Double Check Valve Backflow Preventers for Fire Protection Systems (DVCAF)

Backflow Protection

Table 603.2

CSA B64.7-2011 Laboratory Faucet Vacuum Breakers (LFVB) Backflow Protection

301.2.2, 301.3

CSA B66-2010 Design, Material, and Manufacturing Requirements for Prefabricated Septic Tanks and Sewage Holding Tanks


CSA B79-2008 (R2013) Commercial and Residential Drains and Cleanouts Fixtures DWV Components

418.1

CSA B125.3-2012 Plumbing Fittings Fittings 407.3, 409.4, 410.3, 413.2, 413.3, 606.1, Table 603.2

CSA B128.1-2006/B128.2-2006 (R2011)

Design and Installation of Non-Potable Water Systems/Maintenance and Field Testing of Non-Potable Water Systems (Note 1)


12

CSA B137.1-2013 Polyethylene (PE) Pipe, Tubing, and Fittings for Cold-Water Pressure Services


CSA B137.5-2013 Crosslinked Polyethylene (PEX) Tubing Systems for Pressure Applications


CSA B137.6-2013 Chlorinated Polyvinylchloride (CPVC) Pipe, Tubing, and Fittings for Hot- and Cold-Water Distribution Systems

Piping, Plastic Fittings

Table 604.1

CSA B137.9-2013 Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure-Pipe Systems


CSA B137.10-2013 Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Composite Pressure-Pipe Systems


CSA B137.11-2013 Polypropylene (PP-R) Pipe and Fittings for Pressure Applications


CSA B181.3-2011 2015 Polyolefin and Polyvinylidene Fluoride (PVDF) Laboratory Drainage Systems


CSA B242-2005 (R2011) Groove- and Shoulder-Type Mechanical Pipe Couplings Fittings 301.2.2, 301.3 CSA B356-2010 Water Pressure Reducing Valves for Domestic Water

Supply Systems Valves 301.2.2, 301.3

CSA B481-2012 Grease Interceptors Fixtures DWV Components

1014.1

CSA G401-2007 (R2013) Corrugated Steel Pipe Products Piping, Ferrous 301.2.2, 301.3 CSA LC 1b-20112014 Fuel Gas Piping Systems Using Corrugated Stainless

Steel Tubing (CSST) (same as CSA 6.26b) Fuel Gas 1208.5.3.4

CSA LC 3-2000 (R2005)

Appliance Stands and Drain Pans Miscellaneous 301.2.2, 301.3

CSA LC 4a-2013 Press-Connect Metallic Fittings for Use in Fuel Gas Distribution Systems (same as CSA 6.32a)

Fuel Gas 1208.5.8.1, 1208.5.8.2

CSA Z21.10.1-20132014 Gas Water Heaters , Volume I, Storage Water Heaters with Input Ratings of 75,000 Btu Per Hour or Less (same as CSA 4.1)

Fuel Gas, Appliances

Table 501.1(2)

CSA Z21.10.3-20132014 Gas-Fired Water Heaters , Volume III, Storage Water Heaters with Input Ratings Above 75,000 Btu Per Hour, Circulating and Instantaneous (same as CSA 4.3)


Table 501.1(2), Table L 603.3.2

CSA Z21.12b-1994 (R2010)

Draft Hoods Fuel Gas, Appliances

301.2.2, 301.3

CSA Z21.13-2013 Gas-Fired Low Pressure Steam and Hot Water Boilers (same as CSA 4.9)


301.2.2, 301.3

CSA Z21.15b-2013 Manually Operated Gas Valves for Appliances, Appliance Connector Valves, and Hose End Valves (same as CSA 9.1b)

Fuel Gas 301.2.2, 301.3

CSA Z21.22b-2001 (R2008)2015

Relief Valves for Hot Water Supply Systems (same as CSA 4.4b)

Valves 607.5, 608.7

CSA Z21.24a-2009 (R2011)

Connectors for Gas Appliances (same as CSA 6.10a) Fuel Gas 1212.1(3), 1212.2

CSA Z21.40.1a-1997 (R2012)

Gas-Fired, Heat Activated Air-Conditioning and Heat Pump Appliances (same as CSA 2.91a)


301.2.2, 301.3

CSA Z21.41-20112014 Quick-Disconnect Devices for Use with Gas Fuel Appliances (same as CSA 6.9)

Fuel Gas 1212.6

CSA Z21.47-2012 Gas-Fired Central Furnaces (same as CSA 2.3) Fuel Gas, Appliances

301.2.2, 301.3

CSA Z21.54b-20092014 Gas Hose Connectors for Portable Outdoor Gas-Fired Appliances (same as CSA 8.4b)

Fuel Gas 1212.3.2

CSA Z21.56-2013 Gas-Fired Pool Heaters (same as CSA 4.7) Fuel Gas, Swimming Pools, Spas, and Hot Tubs

301.2.2, 301.3

CSA Z21.69a-2012 Connectors for Movable Gas Appliances (same as CSA 6.16a)

Fuel Gas 1212.1.1

13

CSA Z21.75a-2009 Connectors for Outdoor Gas Appliances and Manufactured Homes (same as CSA 6.27a)

Fuel Gas Appliances

1212.1(4)

CSA Z21.80a-2012 Line Pressure Regulators (same as CSA 6.22a) Fuel Gas 1208.7.2, 1208.7.5(1)

CSA Z21.81a-2007 (R2010)

Cylinder Connection Devices (same as CSA 6.25a) Fuel Gas 301.2.2, 301.3

CSA Z21.86-2008 Vented Gas-Fired Space Heating Appliances (same as CSA 2.32)


301.2.2, 301.3

CSA Z21.90b-2006 (R2011) 2015

Gas Convenience Outlets and Optional Enclosures (same as CSA 6.24b)

Fuel Gas 1212.7

CSA Z21.93-2013 Excess Flow Valves for Natural and LP Gas with Pressures up to 5 psig (same as CSA 6.30)

Fuel Gas 301.2.2, 301.3

CSA Z83.11b-2009 (R2011)

Gas Food Service Equipment (same as CSA 1.8b) Fuel Gas, Appliances

301.2.2, 301.3

CSA Z317.1-2009 Special Requirements for Plumbing Installations in Health Care Facilities


Energy Star-2007 (version 2.0)

Specification for Commercial Dishwashers Appliances L 403.1


Specification for Clothes Washers Appliances L 403.2


Specification for Residential Dishwashers Appliances L 403.1

EPA WaterSense-2007 High-Efficiency Lavatory Faucet Specification Fixtures L 402.5.1 EPA WaterSense-2009 Specification for Flushing Urinals Fixtures L 402.3, Table L

402.1 EPA WaterSense-2011 Specification for Tank-Type Toilets Fixtures L 402.2.1, Table L

402.1 IAPMO IGC 154-2013 Shower and Tub/Shower Enclosures and Shower Panels Fixtures 301.2.2, 301.3 IAPMO IGC 157-2013e1 Ball Valves Valves 301.2.2, 301.3 IAPMO IGC 193-2010 Safety Plates, Plate Straps, Notched Plates and Safety

Collars Miscellaneous 301.2.2, 301.3

IAPMO IGC 226-2006a Drinking Water Fountains With or Without Chiller or Heater

Fixtures 301.2.2, 301.3

IAPMO IGC 276-2011 Bundled Expanded Polystyrene Synthetic Aggregate Units

DWV Components H 301.1(5)

IAPMO PS 23-2006a Dishwasher Drain Airgaps Backflow Protection

301.2.2, 301.3

IAPMO PS 25-2002 Metallic Fittings for Joining Polyethylene Pipe for Water Service and Yard Piping

Joints 301.2.2, 301.3

IAPMO PS 34-2003 Encasement Sleeve for Potable Water Pipe and Tubing Piping 301.2.2, 301.3 IAPMO PS 36-1990 Lead Free Sealing Compounds for Threaded Joints Joints 301.2.2, 301.3 IAPMO PS 37-1990 Black Plastic PVC or PE Pressure-Sensitive Corrosion

Preventive Tape Miscellaneous 301.2.2, 301.3

IAPMO PS 42-2013e1 Pipe Alignment and Secondary Support Systems Miscellaneous 301.2.2, 301.3 IAPMO PS 50-2010 Flush Valves with Dual Flush Device For Water Closets

or Water Closet Tank with an Integral Flush Valves with a Dual Flush Device

Fixtures 301.2.2, 301.3

IAPMO PS 51-2013 Expansion Joints for DWV Piping Systems Joints 301.2.2, 301.3 IAPMO PS 52-2009 Pump/Dose, Sumps and Sewage Ejector Tanks with or

without a Pump DWV Components 301.2.2, 301.3

IAPMO PS 53-2013 Grooved Mechanical Pipe Couplings and Grooved Fittings

Joints 301.2.2, 301.3

IAPMO PS 54-2011a Metallic and Plastic Utility Boxes Miscellaneous 301.2.2, 301.3 IAPMO PS 57-2002 PVC Hydraulically Actuated Diaphragm Type Water

Control Valves Valves 301.2.2, 301.3

IAPMO PS 59-2013 Wastewater Diverter Valves and Diversion Systems DWV Components 301.2.2, 301.3 IAPMO PS 60-1996 Sewage Holding Tank Containing Sewage Ejector

Pump for Direct Mounted Water Closet DWV Components 301.2.2, 301.3

14

IAPMO PS 63-2013 Plastic Leaching Chambers DWV Components H 301.1(5) IAPMO PS 64-2012ae1 Roof Pipe Flashings Miscellaneous 301.2.2, 301.3 IAPMO PS 65-2002 Airgap Units for Water Conditioning Equipment

Installation Backflow Protection

611.2

IAPMO PS 66-2000 Dielectric Waterway Fittings Fittings 301.2.2, 301.3 IAPMO PS

Documents

2016 UPC Report on Proposals