OPERATOR’S MANUAL AND PARTS LISTPRUNER ATTACHMENT

FOR MULTITOOL - THPATTSales & Helpline 01793 333212

www.thehandy.co.ukBefore use please read & understand this manual, paying particular

attention to the safety instructions.

21/11/2013

SAFETY INSTRUCTIONS

Read and understand the owner’s manual and labels affixed to the to the machine. Learn its application and limitations as well as the specific potential hazards. Retain these instructions for future reference.

�� Use sturdy footwear and a helmet with eye and ear protection. Protect exposed parts of your body. Wear heavy duty gloves, preferably made of leather.

�� Do not wear loose clothing or jewellery. Keep hair, clothing and gloves away from moving parts.

�� Do not operate the machine if you are tired, ill or under the influence of alcohol or drugs.

�� Do not smoke when using the machine and ensure caution when handling fuel. We recommend you fuel the machine at least 3m away from where you wish to work to prevent spilt fuel igniting when starting the engine.

�� Ensure that bystanders, children and pets keep well away when starting or trimming - at least 15m.

�� Inspect the machine and all attachments before use for any worn or damaged parts. Do not use until the parts are repaired or replaced.

�� Before starting the engine make sure the attachment is not in contact with anything and have a clear work area and secure footing.

�� The machine should not be exposed to high temperatures or damp and wet conditions.

�� Clean the machine after each use and, if storing for a prolonged period, drain down the fuel in the tank. Remove the spark plug and put a few drops of oil into the cylinder before pulling the starter a 2-3 times to distribute the oil evenly. Replace the spark plug.

�� Regularly check that screws, bolts and nuts are correctly fitted.�� Remove tools from the machine before starting, to prevent them being

thrown by the machine which may cause injuries to the user or bystanders.

�� Do not force the machine. Use the correct machine for the task. The correct machine will do the job better and safer at the rate for which it was designed.

�� Do not use this machine if the switch does not turn it on and off. Any machine that cannot be controlled with the switch is dangerous and must be repaired or replaced before use.

�� When using the pruner attachment please note that the chain is still dangerous while it continues to spin after the throttle trigger is released. Maintain control of the machine until the chain has stopped rotating.

�� Where possible make use of a shoulder harness when using the machine. Adjust the harness to a comfortable operating position before using the machine. Maintain a firm grip on both handles during use. Keep your body clear of the cutting area of the machine.

�� Do not attempt to remove a blockage from a jammed machine before first switching the engine off.

�� If you are interrupted when operating the machine, switch off the engine immediately. Do not allow yourself to be distracted while the machine is on. Turn the machine off before talking to any bystanders.

Page�2

Page�3�

SPECIFICATIONS�

Shaft Straight

Cutting Length 250mm

Chain Bar Type 10”

Net Weight (empty tank) 5.8kg

Declared Sound Pressure Level 98 dB(A)

Declared Sound Power Level 108 dB(A)

Vibration 6.5 m/s2

Gear Ratio 19:15

Max Cutting Speed 14 m/s

PARTS�DIAGRAM�AND�LIST�

No Part No Description Qty

1 TH129-1 Oil Filler Cap 1

3 TH129-3 Fuel Tank Assembly 1

4 TH129-4 Chain HP-166 1

5 TH129-5 Chain Bar 1

6 TH129-6 Chain Bar Cover 1

7 TH129-7 Nut 1

8 TH129-8 Chain Cover 1

9 TH129-9 Chain Tension Adjuster Assy 1

Page 4

• Do not work at an angle higher than 60 degrees as there is a danger of being injured by branches falling without warning. Also be careful not to trip over fallen branches.

Before every use, check the level of the chain oil in the reservoir. After each use clean any oil or saw dust out of the area under the plastic cover with a brush or compressed air. Be especially sure to clean out the oil duct.

Note: After every second chain is worn out, the drive sprocket should be replaced. To change the drive sprocket, remove the spring ring from the drive shaft and pull the drive sprocket and the two washers off the drive shaft. If necessary use a penetrating lubricant. Then slide the replacement parts onto the drive shaft and secure them with the spring ring. It is very important to maintain proper chain tension as incorrect chain tension can cause the guide bar to wear and the chain to come off. You should be able to pull the chain 5-6mm off the bar. If the chain needs to be sharpened a 5/32" chain file should be used, these can be purchased from Handy Garden Machinery under the product code: HP-106. Operating the Pruner: • The Pruner is equipped with a low kickback chain, however, sometimes kickback can occur so

always hold the unit firmly in both hands. • Thin branches can be cut off with a single cut but if the branch is long it is preferable to cut it off in

several pieces. • For larger branches follow the diagrams below for a safe clean cut. Make the first cut from

underneath and cut through one third to half of the branch.

REPLACEMENT OF PRUNER CHAIN

• Remove the sprocket wheel cover. • Remove the guide bar and chain. • Remove the old chain and replace with the new chain. • Mount the guide bar and then fit the saw chain around the bar and sprocket, paying particular

attention to the correct direction of the chain. • Fit the chain tensioner into the lower hole of the guide bar. • Attach the sprocket wheel cover and loosely tighten the nut. • Using the black T-shaped spanner turn the chain tensioner clockwise until the chain fits snugly onto

the guide bar. • Tighten the sprocket wheel cover nut, then using gloves, pull the chain around the guide bar to check

that the chain has the correct tension without any tight spots. • Fill the chain oil reservoir with chain oil and before cutting, run the chain at medium speed to make

sure chain oil is thrown off. This ensures that the chain is being lubricated. Be sure to wipe excessive oil off after filling. You may also want to drain the oil tank after each use to prevent spillage. Oil from the tank can be stored and used, it does not have to be disposed of.

Sprocket

Chain Tension Spigot

ALSO AVAILABLE FROM HANDY

Page 5 

THBCATT Brush Cutter Attachment • Fits Handy, McCulloch, Flymo & Ryobi split shaft trimmers • Durable 655mm straight shaft • Metal cutting blade / Cutting width 205mm • Safety blade guard • Weight 1.9kg

THEXT Extension Bar • Heavy duty steel construction • Quick and simple attachment • Weight 0.8kg

HP-166 Chainsaw Chain 3/8 1.3mm (91vg) 40DL • Fits THPATT Handy Pruner Attachment

THHCATT-A Hedge Cutter Attachment • Fits Handy, McCulloch, Flymo & Ryobi split shaft trimmers • Articulated through 90° for easier hedge trimming • 370mm Blade / 24mm Cutting capacity / 655mm Shaft length • Large blade gap for improved cutting efficiency • Double reciprocating blade / Easy angle adjustment • Compatible with Extension Bar • Weight 2.2kg

GUARANTEE This product is guaranteed against manufacturing defects for a period of 12 months. This does not cover the product where the fault is due to misuse, abuse, use in contravention of the instructions, or where the product has been the subject of unauthorised modifications or alterations. This warranty only covers domestic use and will be void if the tool is used for a commercial application. In the event of a problem with the product within the guarantee period, please contact Customer Service on 01793 333212 or email customerservice@handydistribution.co.uk. If the issue cannot be resolved over the telephone or by email, you may be referred to your local approved service dealer. Please keep your sales receipt as proof of purchase Your statutory rights remain unaffected. Guarantor: Handy Distribution SN3 4NS Whilst every effort is made to accurately represent the product, small variations in colour, design and specification may occur. We reserve the right to alter the product without giving notice. All images are illustrative only and may differ from the product due to ongoing product development.

A SELECTION OF QUALITY PRODUCTS FROM OUR VAST RANGEA SELECTION OF QUALITY PRODUCTS FROM OUR VAST RANGE

HAND PUSH LAWN MOWERSHAND PUSH LAWN MOWERS

ELECTRIC & PETROL BLOW VACSELECTRIC & PETROL BLOW VACS

ELECTRIC & PETROL SHREDDERSELECTRIC & PETROL SHREDDERS

ELECTRIC, PETROL & MANUAL ELECTRIC, PETROL & MANUAL LOG SPLITTERSLOG SPLITTERS

LAWN SWEEPERSLAWN SWEEPERS

PETROL LINE TRIMMERSPETROL LINE TRIMMERS

PETROL BRUSHCUTTERSPETROL BRUSHCUTTERS

PETROL MULTICUTTERSPETROL MULTICUTTERS

ELECTRIC & PETROL CHAINSAWSELECTRIC & PETROL CHAINSAWS

LOG SAW HORSESLOG SAW HORSES

CORDLESS & PETROL CORDLESS & PETROL HEDGETRIMMERSHEDGETRIMMERS

ELECTRIC & PETROL TILLERSELECTRIC & PETROL TILLERS

AERATORS & DETHATHERSAERATORS & DETHATHERS

GARDEN & SALT SPREADERSGARDEN & SALT SPREADERS

PUSH & TOWED ROLLERSPUSH & TOWED ROLLERS

SNOW CLEARANCE TOOLSSNOW CLEARANCE TOOLS

SPRAYERSSPRAYERS

SACK TRUCKSSACK TRUCKS

TROLLEYS & TRAILERSTROLLEYS & TRAILERS

LIGHT CONSTRUCTIONLIGHT CONSTRUCTION

FIND OUT MORE AT WWW.THEHANDY.CO.UKFIND OUT MORE AT WWW.THEHANDY.CO.UK

To order spare parts and see the complete range of garden machinery and garden equipment from Handy, visit:

www.thehandy.co.uk

Spares & Support: 01793 333212