2010 Katalog More Than Tools

2010

2011

TOOLS

MATERIALS

WORKSHOPS

PRODUCT ADVICE

SHARPENING SERVICE

SUSTAINABILITY

EASY ORDERINGTelephone +49 (0)991-9109-902 or +49 (0)1805-9109-902*

Monday till Friday from 8.00 a.m. till 8.00 p.m.

Fax +49 (0)991-9109-802 or +49 (0)1805-9109-802*

Mail address DICK GmbH, Donaustr. 51, 94526 Metten, Germany

Webshop www.more-than-tools.de

Email [email protected]

SERVICEProduct Inquiries +49 (0)991-9109-911 or +49 (0)1805-9109-911*

Workshops +49 (0)991-9109-909 or +49 (0)1805-9109-909*

Tool Sharpening +49 (0)991-9109-910 or +49 (0)1805-9109-910*

*(14 cents/min. from German landlines / calls from mobiles may cost more).

Unlimited free tool sharpening of our Premium Products. Please pay attention to the logo next to the corresponding product ranges and products. Only the shipping charges will be invoiced.

Sharpening pass for a two times free sharpening. Please payattention to the logo next to the corresponding product ranges and products. Only the shipping charges will be invoiced.Sharpening voucher or sharpening pass are contained in the product deliveries.

General tool sharpening (gross prices)

2

Premium

PRICES Net and including gross German VAT

NO-RISK-PURCHASE 30-day return policy

WARRANTY 3 years

IMMEDIATE DELIVERYExport orders are typically shipped within 1-3 days.

SHIPPING CHARGES National Free delivery if exceeding a total gross amount of Euro 150, for allother deliveries less than Euro 150 gross a flat sum of Euro 4.95gross will be invoiced. Express deliveries: you will receive your express delivery the following work day if you order via telephone until 2 p.m.For express deliveries a flat sum of Euro 13 gross will be invoiced.

InternationalFree delivery if exceeding a total gross amount of Euro 357 (Euro300 net). For deliveries less than Euro 300 net shipping chargeswill be invoiced as follows:

Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark,Estonia, Spain, Finland, France, Great Britain, Greece, Hungary,Ireland, Italy, Lithuania, Luxembourg, Latvia, Malta, TheNetherlands, Poland, Portugal, Rumania, Sweden, Slovenia,Slovakia: Euro 9.95 gross (Euro 8.36 net)

Switzerland, Norway, Liechtenstein, Andorra, Monaco, VaticanCity, Greenland, Faroe Islands: Euro 19.95 gross (Euro 16.76 net).

The shipping charges for the remaining countries that are not listed above can be found on our homepage www.more-than-tools.de/shippingcharges.There is no free delivery to these countries.

COME VISIT USOpening hoursMonday till Friday 8 a.m. - 6 p.m.Saturday 9 a.m. - 2 p.m.

Knives..........................6.00 € Axes ......................9.00 €Scissors........................9.00 € Barber scissors ....26.00 €Wood working chisels 12.00 € Chisels ..................9.00 € Plane-blades, carving tools, wood-cutting knives ........9.00 € plus shipping charges

Saws | 700

Chisels | 290

Sculpting tools | 390

Hatchets and axes | 570

Planes | 650

Sharpening devices | 810

Hammers, nails and pry bars | 950

Wood turning tools | 101

Rasps and files | 111

Measuring and inspection instruments | 121

Clamps | 133

Drills, pliers, screwdrivers | 139

Workshop accessories and toolkits | 149

Leather- and paper-working tools | 157

Finishing | 161

Materials | 171

Knives | 181

Razors and scissors | 219

Garden tools | 225

Arts and crafts | 241

Books | 245

Index | 253

General business terms | 257

3

Dear tool friends,

you know us for our »Fine Tools«. But DICK has been much more

than just tools for a long time, which is why we've chosen a new

slogan for this catalogue: »DICK – More than Tools«!

More – that means not just good, fine tools, but also a unique

selection of materials, such as wood, horn, leather and steel,

surface-finishing products as well as arts and crafts products made

from raw materials that you can also obtain from us. And we also

offer you the chance to acquire practical experience on more than

100 courses with highly experienced instructors, some of them

international.

More – that means tools that are not just functional but, above all,

high-quality and aesthetically pleasing. The lasting quality and there-

fore long life of our products means you can enjoy them for a long

time, in keeping with our economic and ecological principles.

We select our products based on their functional aesthetics:

Perfect in use and beautiful in design. They make working fun, and

you achieve the best results while saving time and effort. So you get

double the pleasure: first while you’re working on the object and

later when you enjoy the great result.

More – all DICK products that can be sharpened come with a

sharpening pass for two free sharpenings. Of course we still

sharpen our Premium products free of charge as often as

necessary throughout their service life.

More – this also includes our corporate philosophy. Our name stands

for honesty and fairness in our dealings with our partners. To make

sure we can live up to our customer promise, we test and check all

the tools we offer and use them ourselves. We also guarantee that

our products do not contain any harmful substances.

More – that means: customer satisfaction is our number one priority.

For four years we’ve been able to protect you from price increases.

But now, due to increased raw material cost and currency impacts,

we have no choice but to adjust. However, thanks to the ambitious

process optimisation in our company, we only have to pass on part of

this increase. You can always count on the quality of our products,

because we don't believe in offsetting higher procurement prices

with inferior materials or craftsmanship.

We are delighted to offer you »more than tools« for many years to

come. On behalf of the entire DICK team, I wish you many successful

and creative projects!

Yours,

Petra Steinberger

More than 160 years' experience in fine tools, making musical instruments and crafts:A good reason to be proud of our tradition and success.Today we offer a wide range of top-quality tools and courses at DICK.

What still makes DICK so special today is thecompany's three principles that embody our»More than tools« motto:

Fair, open, sustainable – our philosophyIn everything we do, we make your high demands our own – starting with our respect for nature and people.

Saving resources

We rely on nature for our products and therefore have a natural interest in protectingand conserving it. Efficient and sustainable resource management is of paramount importance to us. We mainly use renewablematerials and conserve natural resources.

Building trust

Honesty and a relationship of trust with all our partners,

suppliers and, of course, our customers is the foundation of

our day-to-day work.

Sharing knowledge – inspiring pleasure

It’s an old but genuine truth that knowledgeand joy shared is knowledge and joy doubled.We are happy to share our know-how with you.Not only through unique, high-quality productsbut also with our

· professional craft courses,· literature and

instructional DVDs,· this catalogue, which not

only shows the products but also provides valuableknowledge on theirtechnology and use,

· expert advice if you have any questions.

This not only allows you to make full use of ourtool, but you will also experience how inspiring,relaxing and enjoyable crafting can be!

4

Premium serviceOur service doesn’t end with delivery of theproduct. It’s important to us to give you thebest ongoing support in your work. That's whywe tailor our services precisely to your needs:

Sharpening pass and Premium sharpening service – free of charge!

∙ With our sharpening pass, you can have the tools and knives you’ve bought from us sharpened twice for free. This service is indicated by the following symbol in our catalogue:

∙ Our Premium sharpening service for DICK Premium products is free of charge as often as you like. This service is indicated by the following symbol for the relevant product series and individual products in our catalogue:

∙ We also sharpen products from other manufacturers. See our webshop or page 2 for prices.

Workshops and courses:

First-hand know-how

Whether traditional techniques, tips or tricks for special tools such asplanes or turning lathes,whether arts and crafts, violin making or metal-working – our wide range of courses and workshopscover all the necessary craft skills... and make your work more enjoyable too!

Spare parts – Gifts – Special orders

Is there anything missing? A replacement blade for your pruning saw, perhaps – a purpose-built item made to measure – or a surprising idea for friends? Whatever it maybe – our service team will be happy to give youexpert advice. Almost all our items can beshipped immediately; orders received before 3 p.m. are usually sent the same day!

Quality: »It's worth it.«In the end, only quality counts -there’s no room for compromise.

Raw materials: Straight from nature

Only selected materials and meticulous workmanship ensure that you can enjoy your tool for a long time.That’s why we use raw and natural materialssuch as wood, horn, stone and leather. But also high-quality steels are our trademark. Our tool care and refinement products, e.g.surface-finishing products, contain no harmfulsubstances and can be used without a secondthought.

»We only sell products we also use ourselves.«

Simply beautiful

Our tools not only cut well – they are also special in their design and handling. And tools that look this good and are so

comfortable to hold will lead to better results, more enjoyment and greater

appreciation of your work.Can there be a nicer compliment

for you and your tool?

Quality assurance at the highest level

With constant quality checks at our suppliersand on our premises in Metten, Germany, wemake sure that each individual tool that we offer undergoes intensive checking using thelatest technology.There are no toxins in our products and no second- or third-class goods.

Our guarantee of origin and quality (3 years’warranty, 30 days' right of return) is not simply an extra – it’s your right and a guarantee you can rely on.

Whether material, tool or workshop: With DICK products and services you’re bound to say: »It’s really worth it.«

Premium

5

NEW:

Courses at DICK – Living and experiencing crafts

At a time when physically demanding work has largely disappearedfrom our everyday lives, we enjoy returning to the skill of creatingsomething with our own hands.Nothing can replace the exhilarating feeling of letting your creativityloose and holding your own creation in your hands at the end. Whet-her you turn a bowl, forge a knife or build your own boat – the result is always something unique thatyou can be proud of.

Living craftsTo guarantee success, we choose our instructors with great care: Our course leaders are the best in their fields, many of them the last in their crafts. We owe the success of our courses to these experienced experts, who joyfully share their invaluable knowledge –they really live their craft!

Unique in EuropeOur course programme comprises around100 different subjects: sharpening toolsand knives, woodworking in carpentry, joinery and turnery, project courses frombuilding a lawn chair right through to a family boat. Sculpting, carving, wicker-weaving, surface-finishing methods, forging and metalworking.

Experiencing craftsOur courses are held in an idyllic setting that ensures relaxation and well-being. You work in small groups using the best tools in our perfectly equipped workshop – ideal conditions for discover-ing hidden manual skills, professional training, and taking your time to try out our full range of tools. Let our highly motivated instructors guide you and experience crafts at their finest.

With nearly 20 years' experience in offering courses and the largest range of courses in Europe, we are passionate experts who consider ourselves lucky to be able to contribute to the preservation of traditional craft methods. We look forward to meeting you on one of our courses!

Your DICK workshop team

Information and registration:Internet: www.more-than-tools.de/workshops

Phone: +49 (0)991-9109-909 or

+49 (0)1805-9109-909*

within Germany

6

Perfect results through clean cuts.

7

Japanese saws | 12

Dozuki saws | 12

Kataba saws | 14

Ryoba saws | 16

Saw sets | 17

Deluxe saws | 18

Quick change saws | 19

Saw cases | 20

Folding saws | 21

Frame and hand saws | 23

Flush-cutting saws | 24

Veneer saws | 24

Back saws | 24

Coping saws | 25

Compass saws | 25

Mitre saws and saw guides | 26

Saws for cutting other materials | 27

Saw accessories | 28

Scroll saw | 28

7

Japanese saws

8

PRECISE CUTTING, CLEAN CUTTING SURFACES, NO RE-WORKING - WOODWORKING IN PERFECTION!

In Japan, woodcraft has a longstanding tradition. As long ago as 300 B.C., iron tools, such

as axes, adzes, chisels and the first precursors of present-day planes, were already used for

woodworking in Japan. The first saws were introduced only a short time later. Over nearly two

millennia of wooden construction, these first saws have developed into fully refined high-

performance tools. Even today, impressive palace and temple buildings, such as the Horyu-ji

temple above built more than 1300 years ago, still attest to the highly developed state of

early. Japanese wood craftsmanship.

WITH US YOU GET THE ORIGINALS As Europe’s largest supplier of Japanese

handicraft tools with more than 20 years of

experience, we have the highest quality

standards for every Japanese saw that leaves

our company.

The saws that we offer are manufactured

exclusively in the Japanese master black-

smiths’ workshops. Saws with interchange-

able blades are manufactured on high-

precision machines and saws with permanent

blades in traditional small workshops. The

quality of these tools fundamentally differs in

many respects from inexpensive Chinese or

Taiwanese imports which sometimes have a

similar appearance. More than 20 testing

processes during manufacture (e.g. the

microscopic final inspection of every saw

blade or the manual sawing test of each

individual Dozuki blade) are followed by a

100% ceck of incoming goods in our company.

Your advantage: You purchase a top product

guaranteed to be 100% fault-free! And our

responsibility doesn’t end with selling the saw.

The supply of replacement parts is also ensured

over the long term.

Rust protection andreduced frictionthanks to cutting edge surface-plating technology (inexpensivesaws are usually only lacquered,leading to increased frictionin the saw kerf!)

No play in saw blade guidancefor best precision

Lighter gripfor fatigue-free working

No play in saw blade attachmentfor smooth, chatter-free sawing

Uniform set of saw teethand absolutely straight teethfor drift-free sawing

Individual impulse-hardened tooth tipsfor enhanced tooth-cracking resistance

Perfect deburring of the teethfor reduced sawing forces

THE FEATURES OF AN ORIGINAL DICK JAPANESE SAW

Japanese saws

9

THE ADVANTAGES OF JAPANESE SAWS

1. Low sawing forces thanks to thin blades

Conventional saws are pushed. This requires

thick blades in order to ensure sufficient

stability. Japanese saws, on the other hand,

are pulled, allowing the use of very thin

blades, as they are only subjected to tensile

stress and cannot warp. The saw kerfs are

therefore finer and the required sawing

forces considerably lower.

Your advantage:

Easy work and little wear.

2. Clean cutting surfaces thanks

to special tooth configuration

Trapezoidal teeth

(crosscut teeth)

Preferred for cuts

across the grain. The teeth are sharpened on

three sides in alternating fashion to cleanly

sever the wood fibres with razor-blade

sharpness, leaving very clean surfaces.

Triangular teeth

(rip teeth)

For sawing along the

grain (ripping). The tooth sizes vary over the

saw’s length to make it easier to start cuts

and improve cutting efficiency.

Universal teeth

A hybrid form of the

above tooth types, for sawing across, along,

and diagonally to the grain.

The knife-sharp special teeth produce clean

working surfaces, which normally no longer

have to be cleaned out with a chisel or

smoothed with a plane.

Your advantage: You save time.

Even with fibrous soft wood, the cutting

edges do not tear out.

Your advantage: The result is visually

more satisfying.

Saw testTooth checking by microscope Quality control at DICK

PULLING allows the use ofa thin blade and keepsthis straight

Thin and clean cuts

PRESSURE requires a thickblade and tends to causewarping

Wide and coarsecuts

THE ADVANTAGES OF JAPANESE SAWSFROM DICK:

Finest steel quality

Impulse-hardened tooth-by-tooth

(every saw tooth has the same hardness,

therefore the saw stays sharper for longer)

Replacement blade service

Quality control at the warehouse in Metten

Uniform and exactly symmetrical tooth

setting (no drifting)

Proof of origin

Tool handles without toxins

(all plastic handles are regularly tested)

HOW DO YOU RECOGNISE AN ORIGINAL DICK JAPANESE SAW?

You can recognise the saw by the DICK label

on the packaging or on the saw blade.

Japanese saws

10

SAW TYPES:

Dozuki

Universal saw with reinforced back

and therefore limited cutting depth.

For precise, thin cuts and fine surfaces.

Kataba

The Kataba is a sturdy saw without

reinforced back for deep, long cuts.

Ryoba

The Ryoba is a double-sided saw with

trapezoidal crosscut teeth on one side

and triangular rip teeth on the other.

The optimum sawing performance is

therefore available for sawing both across

and along the grain.

TIPS FROM EXPERTS

Sawing technique

Saw with less force and even strokes, using

around 2/3 of the blade length. The saw

“bites” under its own weight because of the

unique design of the teeth. The lower the

force exerted, the better the result. During

sawing, change the cutting angle (arching

stroke). This improves the saw’s performance

and the teeth remain free.

Angle

For sawing out mortises or dovetails, firstly

set the saw at a flat angle and saw along the

marking. Only then, tip the saw increasingly

towards the right-angle position and saw

down to the ground.

Marking

For precise cutting, use a marking knife

instead of a pencil. Approach with the saw

so that the line just barely remains.

Which size of saw?

Rule of thumb: The length of the saw blade

should be at least double the length to be

sawed (thickness of the workpiece).

Chattering

If the saw does not cut smoothly, change the

angle of attack (20°-90°) to the workpiece.

Make certain that the workpiece lies on a

solid support or is well clamped so as to

be free of vibrations.

Starting the cut

Use the rear section of the

blade closest to the handle

to start the cut and use the

thumbnail as a guide. Begin

sawing with short strokes.

The right perspective

Guide the saw symmetrically

through your field of vision,

so that the line of sawing is

within view of both eyes.

Two-handed sawing

With larger workpieces,

two-handed guidance is re-

commended, with the (right)

pulling hand at the rear end

of the handle and the (left)

guiding hand close to the

tang.

Rip cuts

Drive a small wedge into the

kerf to prevent the saw blade

from getting jammed and to

make cutting easier.

Cross cuts

When you have made a

shallow cut on the first side,

rotate the piece away from

you. This will improve

guidance and cutting

precision, especially for large

cross-sections.

WHICH SAW IS THE MOST SUITABLE?Aspart from the type (Dozuki, Kataba, Ryoba,

Folding Saw), the intended use (wood, plated

materials, plastic, metal) and the tooth

patterns (for cutting across, along and diago-

nally to the grain), there are a further three

criteria that are important for choosing the

most suitable saw.

These distingushing features are:

Blade thickness, setting and tooth spacing.

Function and explanation:

Blade thickness

The thinner the blade, the quicker and

more energy-efficiently, the cuts can be

made.

Japanese saws are pull saws, therefore the

blades can be manufactured thinner than

those of traditional saws, since they are

under tension. The blade thickness of almost

all saws is constant from the back of the saw

down to the teeth, except for the Silky® saws

and handcrafted saws on pages 14, 18, 21

and 22. It is only possible to measure the

blade thickness of these saws on the back,

as they have hollow grinding.

Setting

The setting affects the possibility of adju-

sting the saw cut as well as the acuteness of

the cut surface and the necessary effort.

Setting describes the bending of the saw

teeth alternating to the right and left side.

Where the setting is measured is not defined

clearly. For easier understanding we specify

the setting by the thickness of the saw blade

at its teeth.

This dimension also corresponds to the width

of the saw kerf. Usually all blades are set,

except on the above-mentioned Silky® saws,

handcrafted (with little setting) and flush-

cutting saws. The setting of the teeth allows

precise cuts without the side of the blade

being in contact with the groove. With no set-

ting, the friction would be too intense, which

would result in too much effort during sawing.

Spacing

Wedge

KEY TO PICTOGRAMS

Crosscut

Trapezoidal-shaped teeth –

mainly for cuts across the grain.

Diagaonal cuts

Universal tooth pattern – for cuts

across, along and diagonal to the

grain.

Ripcut

Rip teeth – mainly for cuts

along the grain.

Particle boards

Especially suited for hard materials

like particle boards.

Metal

Mainly for metal materials.

Plastic

Especially suited for plastic

materials.

Foamed materials

Used to cut foamed and

insulation materials.

Dry wood

Best suited for dry wood.

Wet wood

Best suited for wet and

green wood.

Hollow grinding

Saws with this symbol have a

hollow grinding on the blade and

no setting. This results in the

cleanest cutting surfaces.

Japanese saws

11

The blades of the Silky® saws and handmade

saws are ground hollow or hollowed out by

great effort. This enables extremely clean

cuts and small saw kerfs.

Using the dimensions of the setting and

blade thickness, you will get a measurement

which indicates the possible correction of

the saw direction of the blade and the

cleanliness of the surface. Just deduct the

dimensions of the blade thickness from the

setting. If this dimension is between 0.15

and 0.35mm the direction of the cut is

slightly adjustable. Saws to be used for wet

and green wood or rough cuts should have a

dimension of between 0.15 and 0.35 mm.

Adjusting the cut with saws with dimensions

of 0.1 and 0.15mm is more difficult, but

once the cut is made precisely, you do not

have to readjust it.

The calculated dimension is also

essential for the surface. The higher the

number, the more grooves will occur on the

surface. You will also need less power for cut-

ting. A smaller dimension will result in very

clean surfaces.

Important

Setting - Blade thickness =

between 0.15 and 0.35 mm

• Easy adjustment of the saw cut

• Less strain needed

Setting - Blade thickness =

between 0.1 and 0.15 mm

• Saw makes straight cuts without

adjusting the direction

• Extremely clean surfaces

y y

Normal saws Silky and deluxe-saws

Slight correction of thesaw possible

Hardly any correctionpossible

DICK saw

Knots

Number of strokes required for a specimen 50 x 100 mm (softwood).

Number of specimens cut

Cheap article

DICK saw Cheap article

Tooth spacing

You can tell from the tooth spacing how fast

the saw will cut (feed) and how fine the

cross-section will be. The larger the tooth

spacing, the more material you can take out

of the groove and the faster the saw cuts.

Saws with large tooth spacing leave a less-

clean surface, as only a few teeth cut the sur-

face. A small tooth spacing enables clean

surfaces, as many teeth cut the

surface. The teeth are smaller but cannot cut

as deep per cut and thus, because of their

smaller chip spaces, cannot remove as much

material, as saws with large tooth spacing.

Summary

Tooth spacing between 1.5 and 3.5 mm (tra-

pezoid toothing and universal tooth pattern)

Tooth spacing between 4 and 5 mm

(triangular tooth pattern)

• You will easily reach the cut end

• Slightly coarse cuts

Tooth spacing between 1 and 1.5 mm (trape-

zoid toothing and universal tooth pattern)

Tooth spacing between 3 and 4mm

(triangular tooth pattern)

• Extremely clean cuts

• Slightly inferior cutting performance (feed)

The tooth spacing is measured from one

tooth tip to another. In our printed catalogue

this dimension is always indicated next to the

kind of tooth pattern (e.g. triangular tooth

pattern 1.5 mm).

Saws || Japanese saws

12

Dozuki sawsDozuki saws are indispensable for making wood joints and precise trimmingand pruning. The extremely thin and veryfine-toothed saw blade allows the highestprecision and clean cuts with very littleforce. The reinforced back stabilises theblade and reduces the risk of breaking,but without limiting the possible depth ofcut. Dozuki saws are principally suitedfor softwood and hardwood.

A DOZUKI UNIVERSALThese saws are available in two lengths: the standard blade length of 240 mm forgeneral use in carpentry, andthe version with 180 mm blade length,which has proven itself especially in apprentice training and in the field. Youcan also choose the handle type: withtraditional rattan-wrapped handle, lightand breathable, or rubberised Power Grip,especially durable and slip-proof.

Dozuki Universal 240The most popular Dozuki:Blade length 240 mmOverall length 530 mmCut depth 50 mmBlade thickness 0.30 mmSetting 0.45 mmUniversal toothing 1.50 mm1 Rattan No. 712808 27.65 € 32.90 € 2 Power Grip No. 712830 27.65 € 32.90 €

Repl. blade No. 712908 13.36 € 15.90 €Case p. 20 No. 712871 10.84 € 12.90 €

Dozuki Universal Compact 180Handy and compact:

3 Rattan No. 712110 18.99 € 22.60 € 4 Power Grip No. 712848 18.99 € 22.60 €

Repl. blade No. 712948 12.52 € 14.90 € Case p. 20 No. 712870 9.66 € 11.50 €

»We have been using Dozuki universal saws for years in apprentice training with great success.«P. Winklhofer, Heinrich-Hübsch-Schule, Karlsruhe (Germany)

B DOZUKI UNIVERSAL EXTRA-FINEThe closest-ever tooth pitch of a mass-produced Japanese saw with universal teethis 1.3 mm. The 2 tenths of a millimeterthat distinguish it from the Dozuki Universal are crucial when it comes toachieving even smoother-cut surfaces.In particular, this allows the most precisehardwood joints and the highest bondingstrength in glued joints. You can choosefrom the conventional Dozuki form or thetraditional form. The traditional version ofthe Dozuki has an extra-long back, which increases stability and reduces vibration ofthe blade, and a longer handle for perfectbalance. Made from White Silver Steel, thetraditional version is also harder and has an unsurpassed service life.

1 Dozuki Universal extra-fine 240 conventional

Blade length 240 mmOverall length 530 mmCut depth 50 mmBlade thickness 0.30 mmSetting 0.45 mmUniversal toothing 1.30 mmNo. 712994 28.49 € 33.90 €Repl. blade No. 712996 15.88 € 18.90 €Case p. 20 No. 712871 10.84 € 12.90 €

2 Dozuki Universal extra-fine 240 traditional

Blade length 240 mmOverall length 600 mmCut depth 55 mmBlade thickness 0.30 mmSetting 0.45 mmUniversal toothing 1.30 mmNo. 712995 37.39 € 44.50 €Repl. blade No. 712997 21.76 € 25.90 €Case p. 20 No. 712871 10.84 € 12.90 €

1

A

2

3

4

1

B

2

Japanese saws

UniversalDozuki saws with a universal tooth pattern are especiallysuited for making dovetail andother wood joints, as well as for all precision cuts across and along the grain.

Blade length 180 mmOverall length 395 mmCut depth 45 mmBlade thickness 0.30 mmSetting 0.40 mmUniversal toothing 1.5 mm


13

For precision cuts, hold the handleclose to the tang (shorter strokes), forfast cuts further back (long strokes).

D DOZUKI MINI 150 - CROSSCUTPerfect for smaller cuts and cuts starting mid-panel.Blade length 150 mmOverall length 370 mmCut depth 30 mmBlade thickness 0.30 mmSetting 0.45 mmCrosscut teeth 1.40 mmNo. 712816 21.76 € 25.90 €Repl. blade No. 712916 10.50 € 12.50 €Case p. 20 No. 712870 9.66 € 11.50 €

The blades of the Dozuki Mini sawsNo. 712816 and No. 712780 are exchangeable.

A

E DOZUKI MINI FINE 150 - CROSSCUTCompact back saw for highest-qualitycuts in detail work thanks to a toothspacing of only 1 mm.Blade length 150 mmOverall length 370 mmCut depth 30 mmBlade thickness 0.30 mmSetting 0.35 mmCrosscut teeth 1 mmNo. 712780 23.36 € 27.80 €Repl. blade No. 712880 13.87 € 16.50 €Case p. 20 No. 712870 9.66 € 11.50 €

G DOZUKI SUPER HARD COMPACT 180Available with either slip-resistant, rubberised power grip or classic kiri woodhandle with rattan wrapping.Blade length 180 mmOverall length 395 mmCut depth 45 mmBlade thickness 0.30 mmSetting 0.45 mmCrosscut teeth 1.50 mm1 Rattan No. 712112 20.25 € 24.10 € 2 Power Grip No. 712795 20.25 € 24.10 €


B

C

2

1

D

E

F G 21

Crosscut

A DOZUKI ME 240 - CROSSCUTFor especially fine-cut surfaces:Chatter-free handling due to permanentfixing of back and handle.Blade length 240 mmOverall length 535 mmCut depth 50 mmBlade thickness 0.30 mmSetting 0.45 mmCrosscut teeth 1 mmNo. 712790 35.13 € 41.80 €Repl. blade No. 712890 19.92 € 23.70 €Case p. 20 No. 712871 10.84 € 12.90 €

B DOZUKI TENON 240 - CROSSCUTThe classic Dozuki with a long back,which stabilises the blade and reducesvibration. Made from White Silver Steel,this traditional version is also harder andhas an unsurpassed service life.Blade length 240 mmOverall length 590 mmCut depth 55 mmBlade thickness 0.30 mmSetting 0.40 mmCrosscut teeth 1 mmNo. 712407 39.24 € 46.70 €Repl. blade No. 712507 23.95 € 28.50 €Case p.22 No. 712871 10.84 € 12.90 €

C DOZUKI COMPACT 180 - CROSSCUTHandy and compact:Blade length 180 mmOverall length 395 mmCut depth 45 mmBlade thickness 0.30 mmSetting 0.40 mmCrosscut teeth 1 mm1 Rattan No. 712111 25.63 € 30.50 € 2 Power Grip No. 712846 25.63 € 30.50 €


Particle boards and exotic hardwoodsSpecial wear-resistant teeth forlaminates, particle boards andexotic hardwoods. Mostly used for crosscuts and cutouts.

F DOZUKI SUPER HARDThe curved tip allows cuts to be started mid-panel.

Dozuki Super Hard 240Blade length 240 mmOverall length 530 mmCut depth 50 mmBlade thickness 0.30 mmSetting 0.45 mmCrosscut teeth 1.40 mmNo. 712809 32.69 € 38.90 €Repl. blade No. 712909 15.38 € 18.30 €Case p. 20 No. 712871 10.84 € 12.90 €

Dozuki Super Hard 270Blade length 270 mmOverall length 590 mmCut depth 65 mmBlade thickness 0.30 mmSetting 0.45 mmCrosscut teeth 1.50 mmNo. 712121 33.95 € 40.40 €Repl. blade No. 712122 17.56 € 20.90 €Case p. 20 No. 712852 11.34 € 13.50 €

The trapezoidal-shaped teeth of these saws are suited for precise cuts on wooden jointsacross the grain. They pre-cut the fibreand therefore minimise the risk of tear-outs and guarantee extremely fine surface finishes.


14

Due to their stronger blades, the backlessKataba saws are very robust and makedeep, long or flush cuts in solid or gluedwood or composite material. Like all Japanese saws, Kataba saws work on thepull stroke and are therefore especiallyenergy-efficient. Kataba are offered indifferent blade lengths and tooth spacingfor versatile use in cabinetmaking andcarpentry.

1 Ryoba Blade 240Converts your Kataba 270 into a Ryobadouble-sided saw with crosscut and ripcut tooth patterns.Blade length 240 mmBlade width 82 mmBlade thickness 0.50 mmCrosscut teeth 1.70 mm / Setting 0.75 mmRip teeth 2.80-4 mm / Setting 0.70 mm.No. 712480 14.71 € 17.50 €

D SILKY® KATABA TSUBASA 285 -CROSSCUTRelief-ground blade for low-friction cutting:Due to its taper-ground blade, this sawmakes cuts of unprecedented precisionand with low friction. The teeth have noset, which makes the saw ideal for flushcuts in order to leave the cutting surfacegrooveless. This is an advantage espe-cially for sawn glued joints. The speciallyground raker teeth reduce the cuttingwear of the other teeth, thus increasingthe tool's service life. The lateral bladelocking mechanism increases stabilityand reduces vibration. Robust aluminiumhandle with a soft rubberised grip. Hard-chrome-plated (rustproof) blade with im-pulse-hardened teeth. Comes with arobust, transparent plastic sheath.Blade length 285 mmOverall length 615 mmBlade width 50 mmBlade thickness 0.90 mmCrosscut teeth 1.70 mmNo. 712495 50.34 € 59.90 €Repl. blade No. 712496 26.64 € 31.70 €

Kataba saws

C HATTORI® KATABA 265 - CROSSCUTOriginal Japanese saw at an entry-levelprice.Blade length 265 mmOverall length 590 mmBlade width 60 mmBlade thickness 0.60 mmSetting 0.75 mmCrosscut teeth 1.70 mmNo. 712620 14.96 € 17.80 €Repl. blade No. 712621 6.97 € 8.30 €Case p. 20 No. 712871 10.84 € 12.90 €

E KATABA SPEED SAW 265 - CROSSCUTJapanese saw blade combined with arubberised, pistol-shaped handle inWestern style for effortless trimming,mitre and shoulder cuts. Fast-lockingblade mechanism allows uncomplicatedchanging of blades.Blade length 265 mmOverall length 435 mmBlade width 60 mmBlade thickness 0.60 mmSetting 0.75 mmCrosscut teeth 1.70 mmNo. 712794 20.76 € 24.70 €Repl. blade No. 712894 11.60 € 13.80 €

Ideal for use in conjunction with oursaw guide (712460), see page 26.

A

1

B C

D

E

F KATABA MINI 175 - CROSSCUTMini Kataba in Western design for fine,tear-free cuts.Blade length 175 mmOverall length 300 mmBlade width 47 mmBlade thickness 0.50 mmSetting 0.65 mmCrosscut teeth 1.50 mmNo. 712467 10.17 € 12.10 €Repl. blade No. 712468 6.64 € 7.90 €

Ideal for use with saw guide (set No. 712464), see page 26.

F

UniversalThe universal toothing on the Kataba saw is suited forcuts diagonally, across andalong the grain. Mostly used for bigger joints and for cutting deep recesses.

A KATABA UNIVERSAL 270Becomes a Ryoba in the blink of an eye:Rake teeth quicklytransport the sawdustout of the kerf. The Ryoba blade

(No. 712480),which is available asan accessory, turns theKataba into a Ryoba saw in the blink of an eye. Quick, lever-activated blade-locking mechanism. Comes in a heavy-duty, transparent plastic case.Blade length 270 mmOverall length 570 mmBlade width 60 mmBlade thickness 0.60 mmSetting 0.85 mmCrosscut teeth 1.90 mmNo. 712478 21.18 € 25.20 €Repl. blade No. 712479 12.18 € 14.50 €Case p. 20 No. 712871 10.84 € 12.90 €

CrosscutThe Kataba with crosscut teeth is the right choice for crosscuts in big lumber. Thanks to thetrapezoidal-shaped teeth, thefibre is pre-cut and this saw produces tear-free, clean cuttingsurfaces.

B KATABA 250 - CROSSCUTFor precision cuts with excellent-qualitysurface finishes.Blade length 250 mmOverall length 580 mmBlade width 60 mmBlade thickness 0.50 mmSetting 0.60 mmCrosscut teeth 1.40 mmNo. 712818 25.13 € 29.90 €Repl. blade No. 712918 15.88 € 18.90 €Case p. 20 No. 712871 10.84 € 12.90 €


15

No. 712817 25.13 € 29.90 €Repl. blade No. 712917 15.88 € 18.90 €Case p. 20 No. 712871 10.84 € 12.90 €

D KATABA SUPER HARD 240The most popular Kataba:


E KATABA SUPER HARD COMPACT 180Handy Kataba saws withchoice of slip-resistant, rub-berised plastic handle or tra-ditional classic handle madeof rattan-wrapped kiri wood.Due to the rounded blade tipalso suitable for mid-panel cuts.Blade length 180 mmOverall length 395 mmBlade width 50 mmBlade thickness 0.50 mmSetting 0.80 mmCrosscut teeth 1.50 mm1 Rattan No. 712113 19.50 € 23.20 € 2 Power Grip No. 712845 19.50 € 23.20 €


F HSS KATABA 265Longest edge life:


B KATABA ALPHA - CROSSCUT 265How to make quicker and more precisecuts:This innovative Japanese saw handles evenlarge workpieces, boards and beams. Dueto its curved blade, only part of the teethare in use at a time, the kerf is cleanedbetter and the teeth do not clog. Further-more, cuts along deep markings are easierto control.Blade length 265 mmOverall length 600 mmBlade width 60 mmBlade thickness 0.60 mmSetting 0.85 mmCrosscut teeth 1.80 mmNo. 712014 24.29 € 28.90 €

A KATABA KARIWAKU 333 - CROSSCUTThe most popular carpenter saw:Sturdy saw for larger measurements incabinetmaking and carpentry, also forgreen wood. High cutting performance,even diagonally to the grain, due to mixed tooth pattern. Light, rubberisedaluminium handle.Blade length 333 mmOverall length 705 mmBlade width 55 mmBlade thickness 0.90 mmSetting 1.20 mmCrosscut teeth 2.80 mmNo. 712782 33.11 € 39.40 €Repl. blade No. 712882 16.55 € 19.70 €

How to avoid tear-outs:At the end of the cut use shortstrokes and very little force. That wayyou avoid uncontrolled breaking ofand damage to the blade. Support theworkpiece on both sides to avoidbreakage at the end of the cut. If possible, cut very thin pieces »in packages«.

C D E 1 2

F

A

B


RipcutFor cuts along the grain with unlimited depths, a Kataba saw with rip teeth is the rightchoice. The narrower tooth spacing to-wards the handle facilitates starting thecut and enables a progressive cuttingforce.

C KATABA 250 - RIPCUTFor precision cuts with excellent-qualitysurface finishes.Blade length 250 mmOverall length 580 mmBlade width 60 mmBlade thickness 0.50 mmSetting 0.60 mmRip teeth 2.20-3.40 mm

Particle boards and exotic hardwoodsSpecial wear-resistant teeth for laminates, particle boardsand exotic hardwoods. The backless Kataba design is used for deep cuts.

Sturdy saw for working with high-wear materials.Blade length 240 mmOverall length 540 mmBlade width 65 mmBlade thickness 0.60 mmSetting 0.85 mmCrosscut teeth 1.70 mm

The ultra-strong HSS blade (approx. 68Rockwell) of this saw demonstrates re-mark-able durability and has teeth thatare exceptionally resistant to breakage.

Blade length 265 mmOverall length 600 mmBlade width 60 mmBlade thickness 0.60 mmSetting 0.70 mmCrosscut teeth 1.30 mm


16

Due to its two different cuttingedges, the Ryoba saw offers optimum cutting performance,both for rip and crosscuts. Thismakes it the most versatile sawfor cabinetmakers and carpenters. The trapezoidalteeth make the finest cutsacross the grain. The triangular teeth are ideal for cuttingalong the grain. The teeth become finer from the tip to-wards the tang, whichfacilitates starting thecut and stabilises the blade with a progressive cutting force.

A RYOBA KOMANE 240For fine cuts in cabinetmaking:


A

Ryoba saws

B RYOBA SEIUN - IN 4 LENGTHSFor versatile use in cabinetmaking andcarpentry:Tough and powerful Ryoba in four sizesfor all types of cabinetmaking and carpentry work.

1 Ryoba Seiun 210For detail work in cabinetmaking:Blade length 210 mmOverall length 540 mmBlade width 88 mmBlade thickness 0.45 mmCrosscut teeth 1.40 mmRip teeth 2.50-3.90 mmSetting 0.65 mm / 0.55 mmNo. 712803 22.52 € 26.80 €

2 Ryoba Seiun 240Universal saw for cabinetmakers and carpenters.Blade length 240 mmOverall length 600 mmBlade width 97 mmBlade thickness 0.50 mmCrosscut teeth 1.60 mmRip teeth 2.50-3.90 mmSetting 0.75 mm / 0.70 mmNo. 712804 26.97 € 32.10 €

3 Ryoba Seiun 270Ideal for carpentry joints.Blade length 270 mmOverall length 660 mmBlade width 115 mmBlade thickness 0.60 mmCrosscut teeth 2.30 mmRip teeth 3.60-5.80 mmSetting 0.85 mm / 0.80 mmNo. 712805 28.40 € 33.80 €

4 Ryoba Seiun 300A durable, high-performance saw.Blade length 300 mmOverall length700 mmBlade width 120 mmBlade thickness 0.70 mmCrosscut teeth 3.50 mmRip teeth 3.60-5.80 mmSetting 1 mm / 0.95 mmNo. 712812 31.68 € 37.70 €

C RYOBA COMPACT 180Handy Ryoba saw with classic handlemade of rattan-wrapped kiri wood orpower grip.Blade length 180 mmOverall length 395 mmBlade width 60 mmBlade thickness 0.50 mmCrosscut teeth 1.50 mm / Rip teeth 2.80-3.60 mm / Setting 0.60 mm / 0.70 mm1 Repl. blade No. 712114 20.76 € 24.70 € 2 Power Grip No. 712849 20.76 € 24.70 €






B 1 2 3 4

C

1

2

Versatile saw with especially fine toothpattern, which leaves an extremely finesurface finish.Blade length 240 mmOverall length 580 mmBlade width 84 mmBlade thickness 0.45 mmCrosscut teeth 1.20 mmRip teeth 2.50-3.90 mmSetting 0.65 mm / 0.65 mm

DICK saws undergo a 100% final inspection at the Japanese manufacturer.


17

B BASIC 3-PIECE SAW SETFirst choice for professional work:This popular set of standard-length 240 mm saws will allow you to tacklejust about any cabinetmaking project.The very popular Dozuki Universal (No.712808) is ideal for making dovetailsand other wood joints, the double-edgedRyoba Komane (No. 712806) is one ofthe most versatile saws available for cut-ting solid wood, and the Kataba SuperHard (No. 712204) is capable of takingon rougher jobs and cutting composites.No. 712833 71.34 € 84.90 €

C BASIC 4-PIECE SAW SETAs above but with an additional DozukiTenon saw (No. 712407) for highest-precision cuts and fine surface finishes.No. 712865 108.32 € 128.90 €

D 3-PIECE SAW SET COMPACTHandy sizes for demanding work:The handy, yet sturdy Compact saws with180 mm blade length fit into any toolbag. The 3-piece set includes the DozukiUniversal for dovetails and other woodjoints (No. 712110/712848), the dou-ble-edged Ryoba for deep rip- and cross-cuts (No. 712114/712849), and theKataba Super Hard for laminates, deepmid-panel and flush cuts (No. 712113/712845).1 Rattan No. 712120 56.89 € 67.70 € 2 Power Grip No. 712834 56.89 € 67.70 €

E 4-PIECE SAW SET COMPACT

No. 712863 78.91 € 93.90 €

F CARPENTRY 3-PIECE SAW SETWhen working on site, it’s especially important to have lightweight, high-performance tools. With this trio of saws you will be prepared to take on any bigtask. The Ryoba Seiun 300 (No. 712812)has rip- and crosscut teeth for construct-ing wood joints and for other large-scaleprecision work. The Kariwaku (No. 712782) performs exceptionallywell even when cutting diagonally to thegrain or working with green wood. TheOyakata Professional Folding Saw (No.712738) is an ideal companion whenworking in the field.No. 712864 116.81 € 139.00 €

Precise cuts succeed best with littleforce and calm, even strokes.

A

B

C

D

1

2

E

F

A JAPANESE DUO 2-PIECE SAW SETWith these two versatile saws you areequipped for any jobs in the householdand workshop. Dozuki Universal 240 (No. 712808) for precise cuts across andalong the grain, and Ryoba Komane 240(No. 712806), for deep rip- and crosscuts.No. 712141 56.97 € 67.80 €

As above, but with an additional DozukiCompact - crosscut (No. 712846) forvery precise cuts.

Price advantageSaw setsDepending on the size of the saws, all saw sets come in a jute carrying roll.- 712877 (External dimensions 400 x 400 mm)- 712878 (External dimensions 600 x 600 mm)- 712879 (External dimensions 740 x 740 mm)


18

Deluxe sawsOur hand-made master saws for the highest expectations are aestheticallypleasing surprisingly light and incrediblylong-lived. Their blades are made in nu-merous steps from vacuum-cast whitepaper steel and forge-welded with thetang. After hardening, the smith works onthem with a scraper to produce differen-tiated blade thicknesses: Ryoba bladestaper towards the middle, Kataba andDozuki blades towards the back. Thisproduces friction less strokes with littlevibration and the cleanest cut surfaces.Each blade is straightened by hand witha flattening hammer and signed with agraver by the master smith. The handlesare made of light kiri wood and are generally wrapped in rattan.

The full-hardened blades are more deli-cate than those of saws with replacement blades and should be treated with thegreatest care by experienced craftsmen toavoid breakage of the blade or teeth. Withproper use and care, the saw will last alifetime.

A HON DOZUKI DELUXE - CROSSCUTThe finest Dozuki:Hand-crafted saw for highest-precisioncuts, well-suited for fine cabinetmakingand restoration work. The extremely thinblade and minimal setting (0.1 mm) result in very little cutting loss. Super-light wooden handle, rattan-wrapped.

Hon Dozuki Deluxe 180Blade length 180 mmOverall length 480 mmCut depth 45 mmBlade thickness 0.20 mmSetting 0.30 mmCrosscut teeth 0.80 mmNo. 712212 114.62 € 136.40 €

Hon Dozuki Deluxe 240Blade length 240 mmOverall length 610 mmCut depth 50 mmBlade thickness 0.20 mmSetting 0.30 mmCrosscut teeth 0.80 mmNo. 712213 127.48 € 151.70 €

B DOZUKI DELUXE 240 - RIPCUTIdeal for dovetails and tenons:Hand-forged saw with ripcut teeth formaking high-precision cuts running parallel to the grain.Blade length 240 mmOverall length 600 mmCut depth 45 mmBlade thickness 0.25 mmSetting 0.35 mmRip teeth 1.50 mmNo. 712250 72.18 € 85.90 €Case p. 20 No. 712871 10.84 € 12.90 €

C KATABA DELUXE MINI - CROSSCUTEspecially suited for making violins,model working, restoration and marquetry. Highly flexible blade.

Kataba Deluxe Mini 60Blade length 60 mmOverall length 300 mmBlade width 20 mmBlade thickness 0.30 mmSetting 0.40 mmCrosscut teeth 1 mmNo. 712310 41.93 € 49.90 €

Kataba Deluxe Mini 120Blade length 120 mmOverall length 330 mmBlade width 30 mmBlade thickness 0.30 mmSetting 0.55 mmCrosscut teeth 1 mmNo. 712311 41.93 € 49.90 €

D RYOBA DELUXE 240Hand-crafted, all-purpose saws with twocutting edges, one for cross-cutting and one for ripping.Blade length 240 mmOverall length 600 mmBlade width 105 mmBlade thickness 0.30 mmCrosscut teeth 1.40 mmRip teeth 3.0-4.50 mmSetting 0.75 mm / 0.65 mmNo. 712001 138.57 € 164.90 €Case p. 20 No. 712851 13.03 € 15.50 €

E KOBIKI DELUXE 450Hand saws for large-scale work and ripping logs. The Kobiki Deluxe is notable for its well-proportioned designand well-balanced feel. The angled handle is designed for heavy-duty, two-handed use.

Kobiki Deluxe - crosscutBlade length 450 mmOverall length 700 mmBlade width 85 mmBlade thickness 1 mmSetting 1.50 mmCrosscut teeth 3.30 mmNo. 712291 121.76 € 144.90 €

Kobiki Deluxe - ripcutBlade length 450 mmOverall length 700 mmBlade width 85 mmBlade thickness 1 mmSetting 1.75 mmRip teeth 6.30-7.50 mmNo. 712293 104.96 € 124.90 €

F AZEBIKI 90

No. 712100 27.23 € 32.40 €

A

B

C

D

F

G DELUXE FRET SAWJapanese precisionsaw with reinforcedback for cutting fretgrooves in guitar fin-gerboards. The un-setteeth allow tear-free, perfectly straight cuts. Made by Master Kanzawa, 61 RC, cedar handle.Blade length 120 mmOverall length 320 mmTooth spacing 1.1 mmKerf width 0.57 mmNo. 712260 45.80 € 54.50 €

E

G

Special saw with trapezoidal teeth onone edge and triangu-lar teeth on the otherfor starting cuts mid-panel, cutting groovesand making dovetails. Short, curved blade.Blade length 90 mmOverall length 445 mmBlade width 70 mmBlade thickness 0.45 mmCrosscut teeth 1.20 mmRip teeth 3.30 mmSetting 0.70 mm / 0.90 mm

Case p. 20 No. 712870 9.66 € 11.50 €

Case p. 20 No. 712871 10.84 € 12.90 €


19

Quick-change saws

Infinite possibilities:

Akagashi sawsThe new Akagashi saw is a saw with avery robust handle made of high-gradeJapanese red oak. The saw stands forhigh quality and precision. Now you cancustomise this first-class Japanese sawaccording to your individual needs. Usingthe smart quick-change fastener, you cancombine different top-quality saw bladeswith various hand-made Japanese redoak handles in no time. Simply push upthe lever and pull the saw blade down.The blade is locked twice, it fits tightlyand is not loose. The oiled surface of theergonomically shaped handle accentu-ates the red oak and also the rosewoodband, which conceals the slot of thequick-change fastener. For users, thissaw represents a new dimension in saw-ing – one swift movement is enough tohave a tool with a choice of blades for allyour sawing needs.

A AKAGASHI UNIVERSAL 270For precise cuts along, across or diagonalto the fibre. Strongly set teeth minimizethe friction and allow you to easily cor-rect the direction of the cut. Due to thespecial tooth design with wider spacingthe saw kerf stays clean. The extra-longhandle is very comfortable to hold. Inshort, this saw is an all-rounder.Blade length 270 mmOverall length 520 mmBlade width 60 mmBlade thickness 0.6 mmSetting 0.75 mmCrosscut teeth 1.9 mmNo. 712160 33.11 € 39.40 €

B AKAGASHI FINE 250Fine trapezoid toothing characterises thissuperior saw. The perfect saw for crafts-men who prefer clean-cut surfaces andnarrower saw kerfs. An extra-long handlemakes for a great balanced saw.Blade length 250 mmOverall length 500 mmBlade width 60 mmBlade thickness 0.5 mmSetting 0.6 mmCrosscut teeth 1.4 mmNo. 712162 35.63 € 42.40 €

HANDLES FOR AKAGASHI SAWS SAW BLADES FOR AKAGASHI SAWSG Red oak straight 135 mm No. 712985 20.92 € 24.90 € M Universal 270 No. 712986 12.18 € 14.50 €H Red oak straight 175 mm No. 712984 20.92 € 24.90 € N Fine 250 No. 712988 14.71 € 17.50 €I Red oak straight 215 mm No. 712983 20.92 € 24.90 € O Extra Fine 180 No. 712989 27.65 € 32.90 €J Plastic 210 mm No. 712486 8.82 € 10.50 € P Flush-Cut 170 No. 712992 13.87 € 16.50 €K Red oak curved 165 mm No. 712981 20.92 € 24.90 € Q Keyhole 150 No. 712993 13.03 € 15.50 €L Red oak curved 125 mm No. 712982 20.92 € 24.90 €

For specifications of the saw blades see saw description text.

C AKAGASHI EXTRA FINE 180

D AKAGASHI FLUSH CUT 170

No. 712166 34.79 € 41.40 €

E AKAGASHI KEYHOLE SAW 150This keyhole saw combines ruggednesswith flexibility. The fine toothing allowsexact cutting of curved shapes. An extra-short and bent handle adds to the easyhandling and manoeuvrability.Blade length 150 mmOverall length 340 mmBlade width 10-15 mmBlade thickness 0.6 mmSetting 0.8 mmCrosscut teeth 1.6 mmNo. 712167 33.95 € 40.40 €

F KATABA VARIO 270 - CROSSCUTFor fine cuts in dry wood. Solid plastic case.Blade length 270 mmOverall length 455 mmBlade width 60 mmBlade thickness 0.60 mmSetting 0.75 mmCrosscut teeth 1.80 mmNo. 712471 18.07 € 21.50 €Repl. blade No. 712481 9.83 € 11.70 €

G

H

I

J

KL

M

N

O

P

Q

Kataba Vario Saws, 5-piece setMultiple-use thanks to extra blades:This set covers the entire range of sawingapplications - fromcuts in solid wood to plastics. The quick-release mechanism allows blades to be exchanged in a matterof seconds. Comeswith a protective saw guard made oftransparent plastic. Kataba Vario 270,blade length 270 mm for fine wood cutsand four additional blades 210 mm inlength: rough wood cuts, laminates, bamboo and plastics.No. 712470 46.13 € 54.90 €Repl.handle No. 712486 8.82 € 10.50 €

Price advantage

B

C

D

E

F

A

The 0.3 mm kerf of this saw is almostunsurpassed. The offset of the blade li-mits the cutting depth to 22 mm andtherefore adds a lot of stability. A slightlyshorter handle makes this saw perfect.Blade length 180 mmOverall length 410 mmCut depth 22 mmBlade thickness 0.3 mmCrosscut teeth 1 mm

This flush-cutting saw with its extremelyflexible blade leaves a very smooth cutsurface with no scratch marks. The razor-sharp toothing finishes the job. Becauseof its extra-short handle, this saw may beused in confined and tight spaces.Blade length 210 mmOverall length 335 mmBlade width 35 mmBlade thickness 0.4 mmCrosscut teeth 1 mm

No. 712163 48.57 € 57.80 €


20

Saw cases

Protect your fine Japanese saws fromdust and damage by storing them in asuitable case and thus improving theirtool and edge lives.

A SAW AND TOOL BAGThis extra-long case doesn´t just accom-modate saws of up to 60 cm in length, it also has room for plenty of other toolsand parts. Four interior and six exteriorpockets allow you to organise everythingin limited space. Made of the finest-quality robust nylon with a zip closure and two handles.External dimensions approx. 600 x 170 x 120 mm.No. 712896 41.18 € 49.00 €

B LEATHER CASES FOR DOZUKI AND KATABA

C LEATHER CASES FOR RYOBA

D JUTE CARRYING ROLLSFOR ALL SAW TYPES4 compartments, natural colour.

Size 1Blade width max. 70 mmExternal dimensions 400 x 400 mmNo. 712877 4.96 € 5.90 €



E JAPANESE SAW BAGPractical shoulder bag with DICK logo.Ripstop nylon corduroy with adjustableshoulder strap and compartments for atleast 4 saws up to 75 cm in length. Two separate pockets for replacementblades. Without contents.Overall length max. 750 mmExternal dimensions of the bag 780 x 160 x 60 mmNo. 712895 23.03 € 27.40 €

G SAW TOOTH GUARDPlastic clip-on saw-bladeguard.Overall length 600 mm.No. 712952 1.60 € 1.90 €

F LEATHER CASE FOR FOLDING SAWSWith belt loop. Fits saws No. 712739,712738, 712754, 712752, 712732,712736, 712118, 712107.External dimensions 320 x 90 mmNo. 712853 12.52 € 14.90 €

One-handed cutting:For smaller workpieces, hold the sawwith one hand (if you're right-handedwith the right hand). The workpiecelies on the workbench or small tres-tles; hold it firmly in place with theleft hand. Hold the saw so that thethumb is on the top of the handle inthe direction of the cut, the index finger holds the handle from below,and the other fingers stabilise andguide the saw with little force.

B C

D

E

G

F

A

European cowhide, rivet-reinforcedseams, pushbutton closure, slide-intongue with hang-up hole.

European cowhide, rivet-reinforcedseams, pushbutton closure, slide-intongue with hang-up hole.

Size 1Blade length 150-180 mmBlade width max. 60 mmNo. 712870 9.66 € 11.50 €






Saws || Folding saws

21

Benefit from the advantages of Japanesesaws, even when working in the field.Folded, the blade is protected from toothbreakage. Unfolded, the blade is securelyfastened for working. Thanks to their reli-able mechanism, exact blade guidanceand precise tooth pattern, Japanese fol-ding saws are equal to fixed saws inevery way.

Folding saws

A DOZUKI AND KATABA FOLDING SAWSState-of-the-art saws:The blades of these saws can quickly andeasily be folded into the handle simplyby pressing down the locking lever. Theblades are locked in two positions, withone of them also enabling mid-panelcuts. Due to their tapered blade, thesesaws cut almost frictionlessly, and thehigh-precision teeth have no setting,leaving the cutting surface grooveless.This is an advantage especially for sawnglued joints. Robust aluminium handleswith a non-slip soft rubber grip. Hardchrome-plated (rustproof) bladeswith impulse-hardened teeth.

1 Dozuki Woodboy 240 - crosscutFor the finest cuts. Tapered, hardchrome-plated blade.Blade length 240 mmOverall length 560 mmCut depth 45 mmBlade thickness 0.60 mmCrosscut teeth 0.90 mmNo. 712768 61.51 € 73.20 €Repl. blade No. 712769 30.84 € 36.70 €

2 Kataba Woodboy 240 - crosscutIdeal for deep cuts and surface-protect-ing, flush work due to the un-set toothpattern.Blade length 240 mmOverall length 560 mmBlade width 46 mmBlade thickness 0.70 mmCrosscut teeth 1.10 mmNo. 712766 54.71 € 65.10 €Repl. blade No. 712767 27.39 € 32.60 €

D JOINER´S FOLDING SAW ISHINOKO 210The Ishinoko folding saw stands for finecutting and excellent performance. Withits ergonomically shaped soft rubber handle, it ensures a firm, comfortablegrip and prevents fatigue. Chrome-platedsteel housing, hardchrome-plated blade(rustproof).Blade length 210 mmOverall length 450 mmBlade width 36 mmBlade thickness 1 mmSetting 1.15 mmCrosscut teeth 1.40 mmNo. 712118 18.40 € 21.90 €Repl. blade No. 712119 11.93 € 14.20 €

C HATTORI® KATABA FOLDING SAW 265For fine cuts, suitable for mounting andexpanding, as well as many other tasks incabinetmaking and carpentry. The coatedblade reduces friction and corrosion.Hardwood handle.Blade length 265 mmOverall length 640 mmBlade width 60 mmBlade thickness 0.60 mmSetting 0.95 mmCrosscut teeth 1.60 mmNo. 712763 21.76 € 25.90 €Repl. blade No. 712764 11.68 € 13.90 €

E CUTTER SAW 110This is a compact and versatile saw incutter format, at home both in the work-shop, on a construction site and in thefield. The impulse-hardened tooth tips of the high-grade exchangeable bladeprovide good cutting performance inwood and particle board. The blade canquickly and easily be exchanged for cutter blades.Blade length 103 mmOverall length 230 mmBlade width 18 mmBlade thickness 0.45 mmSetting 0.50 mmCrosscut teeth 1.30 mmNo. 712150 10.84 € 12.90 €Repl. blade No. 712151 5.46 € 6.50 €

1

2

B

D

E

A

Japanese folding sawsfor dry wood

B SILKY® OYAKATA 270 - FINERobust folding saw with fine teeth.The blade has been tapered and has nosetting to minimise friction and guaran-tee clean cutting surfaces, an advantagefor sawn glued joints. The speciallyground raker teeth reduce the cuttingwear of the other teeth, increasing thetool's service life and preventing clog-ging. The hardchrome-plated (rustproof)blade with impulse-hardened crosscuttooth pattern provides high wear-resistance. Robust frame made of die-cast aluminium and a rubberised, non-slip grip.Blade length 270 mmOverall length 560 mmBlade width 35 mmBlade thickness 1 mmCrosscut teeth 1.50 mmNo. 712739 49.16 € 58.50 €Repl. blade No. 712749 25.29 € 30.10 €

2-piece Oyakata SetOyakata fine (No. 712739) with coarse replacement blade (No. 712838).No. 718965 70.84 € 84.30 €

Price advantage

C

Saws || Folding saws

22

No. 712776 29.33 € 34.90 €Repl. blade No. 712777 17.56 € 20.90 €

You can find more folding saws under»Gardening Tools« and online at www.more-than-tools.de

F MINI FOLDING SAW HATTORI®

Unparalleled value for money. Ideal for craft and hobby use.Blade length 150 mmOverall length 355 mmBlade width 24 mmBlade thickness 0.60 mmSetting 0.85 mmCrosscut teeth 2 mmNo. 712734 10.50 € 12.50 €

E ALUMINIUM FOLDING SAW 150Compact featherweight for trekking andcamping:The solid aluminium handle, rubberised,non-slip grip and sturdy, hardchrome-plated blade make this featherweight sawperfect for outdoor activities such ashunting, camping and trekking. Theblade is taper-ground to reduce friction.Blade length 150 mmOverall length 330 mmBlade width 30 mmBlade thickness 0.8 mmSetting 1.3 mmCrosscut teeth 3.5 mm

No. 712748 20.92 € 24.90 €Repl. blade No. 712847 12.52 € 14.90 €

The tooth tips of quality saw replacement blades are individuallyimpulse-hardened,which makes them especially break-proof.

DICK saws havetoxin-free handles(all plastic handlesare regularlytested).

No. 712754 30.84 € 36.70 €Repl. blade No. 712755 16.72 € 19.90 €

No. 712738 49.41 € 58.80 €Repl. blade No. 712838 25.13 € 29.90 €

A

B

C

D

E

F

Japanese folding saws for green wood

A ORIKOMI 250 - COARSEFor wet wood, carpentry and outdoorwork:Optimal cutting performance, even diagonally to the grain, is guaranteed bythis folding saw with sturdy aluminiumconstruction and a non-slip elastomergrip. The trapezoidal toothing has additional clearing teeth added at a ratioof 1:7. A tooth spacing which becomesfiner towards the blade enables a pro-gressive cutting force. The hardchrome-plated blade guarantees a long lifetime.Blade length 250 mmOverall length 510 mmBlade width 32 mmBlade thickness 0.80 mmSetting 1.15 mmCrosscut teeth 2.70-3.60 mm

B SILKY® OYAKATA 270 - COARSEThis robust folding saw with its high cutting performance is ideal for pruningtrees. To enable low friction and cleancutting surfaces, the blade has been tapered and has no setting. A clean cut-ting surface helps water run off quicklyand thus lets the wood dry more quicklyand prevent rotting. The specially groundraker teeth reduce the cutting wear of theother teeth, thus increasing the tool's ser-vice life and preventing clogging. Thehardchrome-plated (rustproof) blade withimpulse-hardened crosscut tooth patternprovides high wear-resistance. Robustframe made of die-cast aluminium and arubberised, non-slip grip.Blade length 270 mmOverall length 560 mmBlade width 35 mmBlade thickness 1.30 mmCrosscut teeth 2.80 mm

2-piece oyakata setOyakata Coarse (No. 712738) with finereplacement blade (No. 712749).No. 718965 70.84 € 84.30 €

Price advantage

C SILKY® BIG BOY 360 - MEDIUMThe perfect saw for carpenters workingwith large timbers.With its length of 360 mm, this saw has one of the longest blades among all folding saws. The chrome-plated blade isrust-resistant, and the impulse-hardenedteeth guarantee a long service life. Thetapered blade has additional raker teethto reduce the cutting wear of the otherteeth and thus increase the tool's servicelife. As the teeth have no setting, thecuts leave the cutting surfaces groove-less. A clean cutting surface helps waterrun off quickly and thus lets the wooddry more quickly and prevent rotting. Therobust, yet light aluminium handle canbe held either with one or both hands,and the rubberised coating provides agood grip in any circumstance. The fol-ding saw can easily be locked and unlocked simply with apress of the thumb, which enables twodifferent working positions of the sawblade and even sawing in places that are difficult to access.Blade length 360 mmOverall length 760 mmBlade width 42 mmBlade thickness 1.30 mmCrosscut teeth 3 mmNo. 712499 50.25 € 59.80 €Repl. blade No. 712500 28.24 € 33.60 €

D POCKET BOY 170 - COARSEWhether for professional woodworkers oroutdoor work, these compact foldingsaws with their razor-sharp teeth easilystand the comparison with bigger saws.The robust metal folding mechanismlocks the blade in two different positions.The taper-ground blade reduces friction,and the soft elastomer non-slip handle isvery comfortable to hold. The taperedblades have additional raker teeth to reduce the cutting wear of the otherteeth and thus increase the tool's servicelife. The teeth are impulse-hardened.Comes with a robust, transparent plasticsheath that can be worn on a belt.

Blade length 170 mmOverall length 370 mmBlade width 30 mmBlade thickness 1.0 mmCrosscut teeth 3 mm

Silky Pocket Boy folded inside its clear case.

Saws || Frame and hand saws

23

Frame and hand saws

A FRAME SAW CLASSIC WITH JAPANESE SAW BLADEThe frame saw Classic combines European tradition with Japanese cutting quality.Both the frame and the saw blades are produced exclusively for DICK. The ergonomically curved cheeks andknobs are made of precious wood withfinely sanded, oiled and polished surfaces.The cedar stretcher lowers the weight ofthe saw and reduces vibrations.

Classic 400 UniversalHandy saw for precision work. With Turbo-Cut universal blade.Blade length 400 mmBlade width 40 mmBlade thickness 0.6 mmSetting 0.85 mmUniversal toothing 1.80 mmExternal dimensions 320 x 700 mmApprox. 550 gNo. 712968 58.74 € 69.90 €Repl. blade No. 712971 18.32 € 21.80 €

Classic 400 Jig BladeFor precise curve cuts. With Turbo-Cut frame-saw blade.Blade length 400 mmBlade width 10 mmBlade thickness 0.6 mmSetting 0.85 mmCrosscut teeth 1.80 mmExternal dimensions 320 x 700 mmApprox. 550 gNo. 712969 58.74 € 69.90 €Repl. blade No. 712972 18.32 € 21.80 €

Classic 500 UniversalThe ideal saw for accurately cuttingdovetails and other wood joints. With Turbo-Cut universal blade.Blade length 500 mmBlade width 40 mmBlade thickness 0.6 mmSetting 0.85 mmUniversal toothing 1.80 mmExternal dimensions 360 x 800 mmApprox. 750 gNo. 712962 66.30 € 78.90 €Repl. blade No. 712956 20.76 € 24.70 €

Classic 600 UniversalThe most popular frame saw:Our most popular and versatile frame sawwith Turbo-Cut universal blade.Blade length 600 mmBlade width 40 mmBlade thickness 0.6 mmSetting 0.85 mmUniversal toothing 2 mmExternal dimensions 360 x 900 mmApprox. 800 gNo. 712964 70.50 € 83.90 €Repl. blade No. 712957 23.45 € 27.90 €

Classic 700 UniversalThis large, heavy-duty frame saw with excellent cutting performance is perfectfor carpentry work. With Turbo-Cut universal blade.Blade length 700 mmBlade width 40 mmBlade thickness 0.6 mmSetting 0.85 mmUniversal toothing 2.20 mmExternal dimensions 410 x 1000 mmApprox. 1100 gNo. 712965 74.71 € 88.90 €Repl. blade No. 712958 26.39 € 31.40 €

B TURBO-CUT FRAME-SAW BLADESJapanese Saw Blades for Upgrading Your Frame Saw:The Japanese high-performance bladesgive your frame saw undreamed-of»turbo« power. Laser-hardened specialtooth patterns make for effortless, truecuts and high surface quality in all woodtypes. The extremely hard tooth tips (degree of hardness over 70 Rockwell,cannot be resharpened) guarantee multi-ple edge life compared to conventionalblades. Blade thickness 0.6 mm.

Available in the following tooth patterns:Universal bladeHighest performancefor cuts across, alongor diagonally to the grain. Universal tooth pattern.Crosscut bladeFor the cleanest cutsacross the grain. Trapezoidal tooth pattern.Ripcut bladeFor cuts along thegrain. Triangular tooth pattern.Jig bladeFor all precise curvedcuts. Trapezoidal tooth pattern.

1 Universal Blade 400Blade length 400 mmBlade width 40 mmBlade thickness 0.6 mmSetting 0.85 mmUniversal toothing 1.80 mmHole distance 370 mmNo. 712971 18.32 € 21.80 €

2 Jig Blade 400Blade length 400 mmBlade width 10 mmBlade thickness 0.6 mmSetting 0.85 mmCrosscut teeth 1.80 mmHole distance 370 mmNo. 712972 18.32 € 21.80 €

Universal Blade 500Blade length 500 mmBlade width 40 mmBlade thickness 0.6 mmSetting 0.85 mmUniversal toothing 1.80 mmHole distance 470 mmNo. 712956 20.76 € 24.70 €

Universal Blade 600Blade length 600 mmBlade width 40 mmBlade thickness 0.6 mmSetting 0.85 mmUniversal toothing 2 mmHole distance 570 mmNo. 712957 23.45 € 27.90 €

Crosscut Blade 600Blade length 600 mmBlade width 40 mmBlade thickness 0.6 mmSetting 0.8 mmCrosscut teeth 2 mmHole distance 570 mmNo. 712950 23.70 € 28.20 €

Rip saw Blade 600Blade length 600 mmBlade width 40 mmBlade thickness 0.6 mmSetting 0.8 mmRip teeth 2.80 mmHole distance 570 mmNo. 712951 23.70 € 28.20 €

Universal Blade 700Blade length 700 mmBlade width 40 mmBlade thickness 0.6 mmSetting 0.85 mmUniversal toothing 2.20 mmHole distance 670 mmNo. 712958 26.39 € 31.40 €

C TURBO-CUT HAND SAWThis classic European hand saw with aJapanese high-performance blade allows precision cuts to be made withbreathtaking speed. The teeth are designed to cut primarily on the pushstroke, but are alsospecially sharpened tocut on the pull strokeas well. Rake teethprevent the saw from clogging and keepit true. Screwed-down hardwood handle.Hardchrome-plated blade (corrosion-free), resharpenable teeth (e.g. with sawfile No. 712802, p. 28).

1 Turbo-Cut Hand Saw 330Blade length 330 mmOverall length 420 mmBlade width 35 - 120 mmBlade thickness 0.80 mmSetting 1.05 mmCrosscut teeth 2 mmNo. 712090 35.21 € 41.90 €

2 Turbo-Cut Hand Saw 450Blade length 450 mmOverall length 540 mmBlade width 37 - 120 mmBlade thickness 1 mmSetting 1.10 mmCrosscut teeth 2.30 mmNo. 712091 41.43 € 49.30 €

A

B

C

1

2

1

2

Saws || Flush-cutting saws, Veneer saws, Back saws

24

A KUGIHIKI 190The blade of this professional Kugihiki isespecially thin and flexible. Traditional,rattan-wrapped wooden handle.Blade length 190 mmOverall length 510 mmBlade width 40 mmBlade thickness 0.30 mmCrosscut teeth 1 mmNo. 712303 35.71 € 42.50 €

Flush-cutting saws B MINI KUGIHIKI 150Simple flush-cutting saw with hardwoodhandle.Blade length 150 mmOverall length 305 mmBlade width 30 mmBlade thickness 0.50 mmCrosscut teeth 1.20 mmNo. 712304 10.84 € 12.90 €

C MINI KUGIHIKI Z-SAW® 150

D JAPANESE VENEER SAW 70For cutting veneer and mid-panel cuts.All-purpose teeth with very little setting.Beech wood handle. Blade length 70 mmOverall length 225 mmBlade width 40 mmBlade thickness 0.50 mmSetting 0.60 mmUniversal toothing 1.30 mmNo. 712703 12.52 € 14.90 €

E GERMAN VENEER SAW 75Veneer saw made in Germany withcranked handle and double-edged, un-set saw blade. Triangular tooth pattern for push and pull strokes.Blade length 75 mmOverall length 195 mmBlade width 50 mmBlade thickness 0.50 mmSetting 0.55 mmRip teeth 1.60 mmNo. 703810 8.82 € 10.50 €Repl. blade No. 703811 5.46 € 6.50 €

Veneer saws

F BACK SAW FOR HARDWOOD 165Japanese cutting force in Western style:

No. 712710 19.24 € 22.90 €

G CRANKED BACK SAW 250

No. 712792 18.15 € 21.60 €Repl. blade No. 712892 14.03 € 16.70 €

H BACK SAWS POWERGRIP 135/150

Back Saw Powergrip 135Blade length 135 mmOverall length 270 mmCut depth 24 mmBlade thickness 0.35 mmSetting 0.55 mmRip teeth 0.70 mmNo. 712713 11.93 € 14.20 €

Back Saw Powergrip 150Blade length 150 mmOverall length 295 mmCut depth 32 mmBlade thickness 0.35 mmSetting 0.55 mmCrosscut teeth 1.30 mmNo. 712714 14.71 € 17.50 €

Back saws

I SILKY® MINI SAW 150

No. 712490 18.07 € 21.50 €Repl. blade No. 712493 11.85 € 14.10 €

J RYOBA RESTAURO 125This compact Japanese saw with two different tooth spacings and extra-thinblade is the first choice for the finestcuts in tight spaces and - thanks to theun-set toothing - for cutting dowels orother protruding wood pieces flush. Theslim blade guarantees minimal cuttingwaste. Handle of Japanese red beech.Blade length 125 mmOverall length 270 mmBlade width 30 mmBlade thickness 0.30 mmSetting 0.30 mmCrosscut teeth 1 / 1.30 mmNo. 712123 15.88 € 18.90 €

K KATABA RESTAURO 100Compact Japanese saw for fine repair cutsand working in confined spaces. The extremely fine, un-set teeth leave veryclean surfaces behind. The thin blademinimises the amount of cutting waste.Blade length 100 mmOverall length 220 mmBlade width 20 mmBlade thickness 0.30 mmCrosscut teeth 1 mmNo. 712309 15.38 € 18.30 €

A

B

C

D

E

F

G

H

I

J

K

Japanese flush-cutting saws are ideal forcutting dowels, pegs, tenons etc. flush tothe surface of the piece without dama-ging its surface. Flexible blades with un-set teeth, limited cutting depth.

Small flush-cutting saw for flush cutswithout damaging surfaces. Replaceableblade, hardchrome-plated. Lightweightplastic handle. Double cutting edge.Blade length 150 mmOverall length 300 mmBlade width 35 mmBlade thickness 0.40 mmCrosscut teeth 1.20 / 1.50 mmNo. 712321 10.67 € 12.70 €Repl. blade No. 712323 7.14 € 8.50 €

Ideal for flush cuts ofall types. ReversibleJapanese blade. Hardwood handle.Blade length 250 mmOverall length 400 mmCut depth 42 mmBlade thickness 0.50 mmSetting 0.85 mmCrosscut teeth 1.80 mm

Small Japanese replaceable-blade sawsfor all fine wood cuts in model and hobbywork. The rubberised handle fits thehand comfortably.

Repl. blade No. 712699 6.39 € 7.60 €

Repl. blade No. 712716 7.73 € 9.20 €

Multi-purpose Japanese compact saw with tip-hardenedspecial tooth pattern,for cutting on the push and the pull. Also suitable for children. Slip-proof,rubberised handle, reliable blade lockingmechanism.Blade length 150 mmOverall length 260 mmBlade width 45 mmBlade thickness 0.50 mmSetting 0.85 mmUniversal toothing 1 mm

Small, pull-stroke saw with reinforcedblade back for detailed work on models,musical instruments and in restoration.No setting.Blade length 165 mmOverall length 290 mmCut depth 30 mmBlade thickness 0.30 mmRip teeth 0.90 mm

Saws || Coping saws, Compass saws

25

A COPING SAWS GLARDON/VALLORBE®

Precision Coping Saws for ProfessionalUse:High-precision, professional coping sawby Swiss manufacturer Glardon. Perfectfor intarsia, mother-of-pearl or goldsmithwork and other artisan and precise me-chanical applications. Tension length adjustable up to 150 mm, frame andmountings aluminium. Comes without blade.

Jaw depth1 75 mm No. 712521 30.76 € 36.60 € 2 100 mm No. 712525 36.89 € 43.90 €

Coping saws

SUPER GLARDON® SAW BLADES, STANDARD TOOTH PATTERNCoping-saw blades of the highest quality.Spring steel with rounded back. Blade length 130 mm. Pack of 12.

FineBlade width 0.36 mmBlade thickness 0.18 mmSetting 0.21 mmRip teeth 0.3 mmNo. 712522 3.28 € 3.90 €

MediumBlade width 0.58 mmBlade thickness 0.28 mmSetting 0.32 mmRip teeth 0.5 mmNo. 712523 2.69 € 3.20 €

CoarseBlade length 130 mmBlade width 0.94 mmBlade thickness 0.40 mmSetting 0.48 mmRip teeth 0.8 mmNo. 712524 2.94 € 3.50 €

FineBlade thickness 0.70 mmNo. 712530 3.28 € 3.90 €

MediumBlade thickness 0.75 mmNo. 712531 3.28 € 3.90 €

CoarseBlade thickness 0.85 mmNo. 712532 3.28 € 3.90 €

B JAPANESE COPING SAW

No. 712517 24.62 € 29.30 €

Freeway®

C FREEWAY® DIAMOND SAWFor hard materials:The diamond particles embedded in theblade allow this saw to be used for cutting the hardest materials, such assteel, stone, ceramic or glass, in any di-rection. Comes with one diamond sawblade and one conventional blade.Blade length 125 mmOverall length 290 mmBlade thickness 1.6 mm / 1 mmDepth 120 mmNo. 712514 17.56 € 20.90 €2 Replacement bladesNo. 712515 12.52 € 14.90 €

D COPING SAW FREEWAY®

Sturdy coping saw for hobby use, training and school:The tough, spiral-tooth saw wire allowsyou to make cuts in any direction withoutturning the saw. The case-hardened sawwire (Ø 1 mm) is highly resistant tobreakage and wear and therefore ideal for school and training use. Each saw comes with 2 saw wires.Blade length 125 mmOverall length 290 mmBlade thickness 1 mmDepth 120 mmNo. 712512 12.27 € 14.60 €2 Replacement bladesNo. 712513 3.61 € 4.30 €

E LONG COMPASS SAW 210

No. 712601 12.52 € 14.90 €

F SHORT COMPASS SAW 120

No. 712602 9.16 € 10.90 €

Compass saws

A

1

2

B

C

D

E

F

With its great depth, this Japanese steel-frame coping saw is perfectly suited fordeep cuts. The saw blade, fixed with twohand knobs, is easily tightened by turning the handle. A metal sleeve insidethe handle allows for precise adjustmentof the tension in single-handed opera-tion. If necessary, the blade-holdingclamps can be set up in 4 positions ifturning the saw is not possible. Chrome-plated frame, plastic handle, weight 230g. Comes with 3 blades (we recommend Super Glardon Saw Blades as replacement blades).Blade length 130 mmOverall length 300 mmBlade width 1 mmBlade thickness 0.40 mmSetting 0.50 mmRip teeth 0.8 mmDepth 250 mm

Freeway saws come with a robust steelframe, which ensures high torsion resist-ance. A clamp at the end of every sawblade is easily hooked onto the socketand tightened by turning the handle.

With long, slender Japanese blades formaking holes and curved cuts and working in confined spaces.

Robust, blued blade with wide tooth spacing for rough cut-outs. Handle madefrom beech with hang-up hole.Blade length 210 mmOverall length 345 mmBlade width 5-14 mmBlade thickness 1.30 mmSetting 1.40 mmUniversal toothing 1.60 mm

Ideal for working in confined spaces and for precise curved cuts and cut-outs. Rosewood handle.Blade length 120 mmOverall length 245 mmBlade width 3-14 mmBlade thickness 0.60 mmSetting 0.70 mmUniversal toothing 1.10 mm

SUPER GLARDON® SAW BLADES, SPIRAL TOOTH PATTERNFor cuts in any direction without having to turn the saw, very easy to use.Blade length 130 mm.Packs of 12.

Saws || Mitre saws and saw guides

26

A NOBEX® DOUBLE MITRE SAW CHAMPION 180 - SETWith Japanese blade.Precise, versatile mitre saw made in Sweden with aluminium body machinedso the stock lies perfectly flat, exactmetal guides that ensure straight cuts,and a guide that can be locked at anyangle with additional fixed stops. Two integrated clamps hold the workpiecetight, long pieces are supported by apull-out support. Extra details like thelength stop, cutting depth lock-out orcompound mitre function set this multi-functional tool apart, as does the Japan-ese high-performance blade, whichallows effortless, extremely quick cuttingin solid wood. Set includes fine-toothsaw blade CH-32 and Japanese high-per-formance saw blade CH-16 JP.Fixed angles for 4-, 5-, 6-, 8-, 12-cornered frames and 90° cuts,accuracy +/- 0.08°, approx. 5 kgBlade length 630 mmTable length 500 mmMax. depth of cut 180 mmNo. 712533 167.98 € 199.90 €

SAW BLADES FOR NOBEX® DOUBLEMITRE SAW CHAMPION 180

For wood, Japanese tooth patternBlade length 630 mmBlade width 40 mmBlade thickness 0.8 mmSetting 1 mmCrosscut teeth 1.6 mmNo. 712534 35.21 € 41.90 €

For metal (HSS bi-metal, extra hard)Blade length 630 mmBlade width 19 mmBlade thickness 1 mmSetting 1.3 mmRip teeth 1 mmNo. 712537 19.83 € 23.60 €

For fine cuts in woodBlade length 630 mmBlade width 40 mmBlade thickness 0.8 mmSetting 1.2 mmRip teeth 1 mmNo. 712536 11.09 € 13.20 €

For hardwood and hard plasticsBlade length 630 mmBlade width 40 mmBlade thickness 0.8 mmSetting 1.2 mmRip teeth 1.40 mmNo. 712535 11.09 € 13.20 €

B TURBO-CUT MITRE SAW BLADE 550The Japanese Turbo-Cut blade makesrazor-sharp, high-quality cuts, even whencutting hardwood. This allows maximumprecision when making frames and cutting boards and squares to size.Trapezoidal teeth designed to cut on thepull stroke, with rake teeth, hardenedtips. Fits most standard mitre saws.Note: Cannot be used in the double mitresaw Champion 180, No. 712533!

Blade length 550 mmBlade width 45 mmBlade thickness 0.70 mmSetting 1 mmCrosscut teeth 1.80 mmHole distance 515 mmNo. 712980 20.50 € 24.40 €

A

C SAW GUIDE Z-SAW®

This saw guide is fully adjustable inmitre and angle of inclination, makingaccurate, straight and very clean cuts ofledges, frames and joints. The slidingfence allows boards to be trimmed orbevelled easily. Adjustable from +/- 0°-45°, made of galvanised steel. Comeswith protractor, positioning and slidingfence, dummy blade, Allen key and detailed instructions. Suitable for saws with blade thicknesses between 0.4 and 0.6 mm; we recommend the

Kataba Speed Saw No. 712794.No. 712460 34.37 € 40.90 €

Saw Guide SetPrecision saw guide (No. 712460) withKataba Speed Saw 265 (No. 712794)included.No. 712461 50.34 € 59.90 €

Price advantage

Mitres Polygons Lap joints

45°

45°

0°

45° 45°0°

Mitre angles Inclination angles

D SAW GUIDE SET MINI Z-SAW®

For right-angled trimming of squared timber and ledges, as well as precise 45° mitre cuts. Mitres can be cut at anyangle with the setting gauge and a screwclamp. With the length stop in place, itis even possible to precisely cut boardsand panels by hand. Set: Mitre block, including 90° guide,45° guide, length stop, setting gauge,Kataba Mini saw (No. 712467) and instructions.No. 712464 31.68 € 37.70 €

Mitre saws and saw guides

Aluminiumbody

Precisionguide designedto fit theKatabaMini saw

Removable fence, mounts on either side

C

B

D

Adjustments to be made with saw guide Z-Saw.

Saws || Saws for cutting other materials

27

Saws for metal

A HANDIWORK METAL 150Back saws for non-hardened metals andhard plastics. The rubber handle sitscomfortably and securely in the hand.Blades replaceable.Blade length 150 mmOverall length 295 mmBlade width 30 mmBlade thickness 0.35 mmSetting 0.65 mmRip teeth 0.90 mmNo. 712715 13.78 € 16.40 €Repl. blade No. 712704 6.97 € 8.30 €

Saws for cutting other materials

B SMALL METAL SAWFor cuts in hard-to-reach places, ideal for the tool bag. The saw blade integratedinto the handle can be pulled past thesmall clamp, making flush cuts possible.Sturdy die-cast aluminium. Comes with 250 mm saw blade.Blade length 90 - 250 mmOverall length 370 mmBlade width 12 mmBlade thickness 0.6 mmSetting 0.90 mmTeeth per inch 24No. 703812 10.00 € 11.90 €

C METAL COPING SAWSits securely in your hand:Sturdy coping saw with rubberisedhandle for a secure grip. The adjustableframe made from die-cast aluminiumtakes saw blades of either 250 mm or300 mm lengths. The saw blade can belocked in different positions via a quick-release lever. Comes with 300 mm sawblade.Blade length 300 mmOverall length 455 mmBlade width 12 mmBlade thickness 0.6 mmSetting 0.90 mmTeeth per inch 32No. 712540 33.53 € 39.90 €

Replacement blades for Metal Coping SawJapanese top quality, long edge life andsharpness. HSS steel. 2-piece set.Blade length Teeth per inch250 mm 18 No. 712541 7.23 € 8.60 €

32 No. 712542 7.23 € 8.60 €300 mm 18 No. 712544 7.23 € 8.60 €

32 No. 712546 7.23 € 8.60 €

Saws for plastics

D SAW FOR PLASTICFor hard and soft plastics, plywood andcomposite materials. Backless saw withslender, replaceable blade and pistol-shaped, rubberised handle. Blade length 240 mmOverall length 380 mmBlade width 32 mmBlade thickness 0.5 mmSetting 0.75 mmCrosscut teeth 1.5 mmNo. 712503 16.30 € 19.40 €Repl. blade No. 712504 4.96 € 5.90 €

E HARD MATERIAL SAW SELECT 250Specially designed saw for cutting iron,brass, copper, aluminium, hard plastic,and plated materials (plasterboard). The fine, triangular teeth of the blade are coated to reduce friction. The sturdy aluminium handle covered with soft rubber fits comfortably in the hand. Blade length 250 mmOverall length 400 mmBlade width 35 mmBlade thickness 0.70 mmSetting 0.90 mmUniversal toothing 1.80 mmNo. 712610 18.40 € 21.90 €Repl. blade No. 712611 5.71 € 6.80 €

F FOLDING SAW FOR PLASTIC

No. 712023 27.65 € 32.90 €

G INSULATION CUTTER 250The serrated blade ofhigh-strength, hard-chrome-plated specialsteel (60 Rockwell) isespecially suited forinsulating and foamedmaterial, polystyrene,felt and cardboard.Blade length 250 mmOverall length 380 mmBlade width 34 mmBlade thickness 0.9 mmNo. 710751 19.24 € 22.90 €

A B

C

D

E

F

G

This folding saw for plastic can be useduniversally on any building site. Whetherfor hard plastics (e.g. rigid PVC pipes) orcompounds (e.g. insulation boards or softplastics), the crosscut teeth guaranteethe best cutting performance. The aluminium handle with anti-slip rubber coating provides a comfortablegrip, and thanks to the robust foldingmechanism, the saw can be securely tucked away when not in use.Blade length 200 mmOverall length 420 mmBlade width 35 mmBlade thickness 0.60 mmSetting 1 mmCrosscut teeth 1.30 mm

Repl. blade No. 712024 15.04 € 17.90 €

Saws || Saw accessories, scroll saw

28

In Japan, traditional saws are set byhand on an anvil.

Things worth knowing:

Please note that all Japanese saws withexchangeable blades have a tooth-tiphardening of over 70 Rockwell. Through abrasion when resharpening atooth, it is possible to reach the rangeof basic hardness (approx. 60 Rockwell), causing a decrease in hardness andthus a shorter edge life!

Set of teeth: After sharpening the teeth,the toothing generally also needs to beset again. This is a very demanding taskfor fine-toothed Japanese saws.

B DIAMOND SAW FILESaw file with wear-resistant, diamond-coated surface, especially for very hard,tip-hardened teeth.Ø 2.8 x 20 mmStroke length 100 mmNo. 712802 27.31 € 32.50 €

C SAW FILESDiamond-shaped precision files forsharpening Japanese saw blades withouttip-hardened teeth (Deluxe saws withfull-hardened, non-exchangeable blades).

Very fine2.5 x 17 mmCut length 75 mmNo. 712813 7.82 € 9.30 €

Fine3.0 x 20 mmCut length 100 mmNo. 712814 8.66 € 10.30 €

D HEGNER® SCROLL SAW MULTICUT-SEHegner precision saws are considered the best on the market. Due to the con-tinuously rated motor with electronicallyand progressively adjustable speed regulation, it is possible to cut wood,metal and plastic effortlessly and pre-cisely. Easy exchanging of blades thanksto a speed lock mechanism and ad-justable saw blade tension, saw strokeadjustable to either 19 or 12 mm. Base and table of gray cast iron, tablesurface precision-ground. The saw bench (435 x 230 mm) can be inclined progressively and, thanks to the scaling, precisely to 45° or 12°. With exhaustnozzle, Ø 35 mm. Pass length 460 mm,pass height 65 mm.100 W motor, 230 V, 400-1400 tpm, 23 kg.

Includes: Assortment of quality sawblades (76 pcs.), 2 saw-blade clamps0.7 mm, 2 screws for saw-blade clamps,1 special clamp for internal cuts, 1 plastic table insert, 2 replacement rollsfor quick gripping, 1 set operating tools, detailed instruction manual.No. 704805 735.29 € 875.00 €

HEGNER® QUALITY SAW BLADESFor wood, plastics and soft metals. In gross (144 pcs). Also fits

Super Glardon® saw blades, see page 25. Length 130 mm.

Blade width x Blade thickness0.65 x 0.30 mm No. 704815 20.50 € 24.40 € 0.80 x 0.34 mm No. 704816 20.50 € 24.40 € 1.20 x 0.38 mm No. 704817 20.50 € 24.40 € 1.35 x 0.50 mm No. 704818 20.92 € 24.90 € 1.70 x 0.55 mm No. 704819 21.43 € 25.50 €

Saw accessories

Scroll saw

A SAW SET PLIERSFor Japanese and Western saws with adjustable depth stop for settings of 0.7-2.0 mm. By turning the depth-stopplate, with its spiral-shaped increasingbevel, different setting measurementscan be adjusted. HSS plunger, aluminium body.Overall length 180 mm

A

1

2

B

C

D

1 Size 1Plunger width 1.5 mm, suitalbe for toothspacing` s from 1.5 mm.No. 711990 16.72 € 19.90 €

2 Size 2Plunger width 2.2 mm, suitalbe for toothspacings from 2.2 mm.No. 717848 18.91 € 22.50 €

Japanese type | 31

Striking chisels for cabinet work | 31

Finishing chisels for cabinet work | 33

Striking chisels for carpentry work | 34

Finishing chisels for carpentry work | 35

Hybrid chisels | 35

Western type | 36

Chinese chisels | 37

Tool rolls and accessories | 38

29

For perfect joints

Chisels

30

We distinguish between finishing chisels for

light to moderate work and striking chisels for

heavy-duty work. Finishing chisels are usually

pounded by hand. They therefore have no

steel hoops at the handle end. Striking chisels,

on the other hand, are driven by striking the

tool (wooden mallet for Western chisels and

iron-headed hammer for Japanese chisels).

With regard to the blade, they are there fore

designed more sturdily, and have a hoop at

the handle end. We distinguish between the

following types:

A Tang chisels:

Classic design, ensuring firm anchoring of

the blade in the handle. On cheap tools with-

out an additional steel ferrule, the handles

may split under heavy blows.

B Socket chisels:

This design allows a continuous transition

from the neck to the handle and thus comfort-

able ergonomics. Through the conical fit of

the socket, strong forces can be transmitted

during striking.

C Japanese chisels (Nomi):

This design combines the benefits of both

types above.

…INDISPENSABLE FOR ACCURATE WOODWORKING!

JAPANESE CHISELS Wherever high precision is required for working

solid wood, for jointwork in the manufacture

of fine furniture, or for the making of musical

instruments, Nomi are indispensable. They

have the following advantages:

Blades of two-layered steel

Soft iron, protects the blade against cracking

and absorbs the shocks of the hammer blows,

forge-welded with a thin layer of extremely

hard carbon-steel (with the exception of HSS

Nomi). The hardness values are 62-63 and 66

(HSS steel) on the Rockwell scale.

Tapered blades

The blade is set at a slight angle to the tang

to increase the working depth to nearly double

the blade length.

Integral design

The neck is seamlessly integrated in the

handle and therefore lies comfortably in the

hand. The solid conical steel ferrule protects

the handle against fracture or becoming loose

when struck with the iron-headed hammer.

Hollow-ground back

The hollow relief (ura) on the back of the blade

reduces the contact surface and therefore

also the friction and the required cutting

force. It also simplifies sharpening, as only

the edges of the hard carbon-steel back of

the blade need to be lapped. Due to the

abrasion during sharpening, the straight cutt-

ing edge remains intact, even though the

blade becomes shorter through sharpening

over time (see illustration below).

Sharpening Japanese chisels

Use only fine-grained Japanese waterstones

with grit 1000-2000 for sharpening and

1000-4000 for finishing. Work on the bevel

and rear side until the concave relief is out-

side the cutting edge (see illustration below).

The back lies completely flat on the stone.

Make sure that the sharpening and

finishing stone is 100% flat!

WESTERN CHISELS As a rule, these are made of alloyed steels

with relatively sturdy blades and little danger

of chipping. In particular the finely manufactu-

red Pfeil chisels in traditional central Euro-

pean design have proven ideal for universal use.

CHINESE CHISELS Traditional Chinese chisels are convincing in

terms of their durable, crack-resistant HSS

steel blades, which also withstand rough

treatment during restoration or joiner’s work.

The working of wear-inducing composite ma-

terials is also no problem for these chisels.

The tapered shape of the blades is advan-

tageous for working into corners and under-

cutting. The value for money of these chisels

is unbeatable.

NEWSharpening pass

Two free sharpenings.

(see page 2).

Sharpening service

Free lifetime sharpening for Premium

products. (see page 2).

Japanese chisel design

Hollowback

Neck

Tang

Taperedblade

Hollow back after repeated sparpening and finishing

Steelferrule

Hoop

Socket

Tang Tang

Hoop

Steel ferrule

C

B

A

Chisels || Japanese type

31

2 6-piece set Price advantage

No. 710137 281.51 € 335.00 €

No. 710136 167.98 € 199.90 €

No. 710170 414.29 € 493.00 €

No. 710230 233.53 € 277.90 €

Japanese typeStriking chisels for cabinet work

A MOKUME NOMI

1 Single chiselsBlade width9 mm No. 718950 158.82 € 189.00 € 12 mm No. 718951 174.79 € 208.00 € 18 mm No. 718952 192.44 € 229.00 € 24 mm No. 718953 213.45 € 254.00 € 30 mm No. 718954 226.05 € 269.00 € 36 mm No. 718955 254.62 € 303.00 €

6-piece set in a leather tool roll:9-36 mmNo. 718960 1183.19 € 1408.00 €

Precision chiselling:Due to their wedge-shapedbevel, chisels tend to drifttowards the back of theblade when struck. There-fore, in precision work, youshould not chisel rightalong the mark. Work witha clearance of 1 to 2 mmfrom the mark initially,then do the finishing work.

A

B CHU-GATA NOMIHand-worked blades for connoisseurs:These premium-quality chisels are ex-tremely durable. The blade is laminatedwith White Paper Steel, and finished bymeans of hand-forging with low deformation. Like sword steel, thismaterial is smelted from purest ironsand.The back of the blade has multiplegrooves for improved support when working near edges. Boxwood handle.Blade length 60 mmOverall length 225 mmBlade thickness 5-7.5 mm

1 Single chiselsBlade width3 mm No. 710160 29.33 € 34.90 € 6 mm No. 710161 29.33 € 34.90 € 9 mm No. 710162 29.33 € 34.90 € 12 mm No. 710163 35.55 € 42.30 € 15 mm No. 710164 36.55 € 43.50 € 18 mm No. 710165 37.56 € 44.70 € 24 mm No. 710166 43.28 € 51.50 € 30 mm No. 710167 45.29 € 53.90 € 36 mm No. 710168 53.36 € 63.50 € 42 mm No. 710169 56.97 € 67.80 €

6-piece set6-piece set in a leather tool roll:6/9/12/18/24/30 mm

2 10-piece set10-piece set in a leather tool roll: 3-42 mm

C OIRE NOMIFor the professional:



2 10-piece set10-piece set in a leather tool roll:3-36 mm

1

B

1

C

1

Price advantage

Price advantage

2

2

2

Price advantage

Price advantage

Wherever absolute precision is required,when working even the hardest of woods,Japanese chisels (Nomi) are the firstchoice. The meticulous workmanshipwith which they are made, the multi-laye-red, ultra-sharp blades, the outstandingedge life, and of course the compact design, allow you to work ergonomically,comfortably and precisely. The soft ironbody prevents brittle fractures in thedouble-layered blade and dampens theforce of the strike. The thin cutting layerof carbon-steel is extremely hard-, unlessotherwise noted, 62-63 HRC - while theHSS Nomi models exhibit a hardness of66 HRC. Due to the angled blade, thecutting depth is increased to almosttwice the blade length. As the back ofthe blade is hollow-ground, the contactsurface is reduced, which in turndecreases the friction and the necessarycutting force. The handles, made oftough Japanese hardwoods, are mountedwith sturdy steel ferrules at both ends,and are designed for efficiency whendriven by an iron hammer.

With skillful handling of fire and iron, themaster blacksmith Akio Tasai lends thishighly aesthetic chisel a wood-like struc-ture (Mokume). The folds appear on thesurface like a relief, and make eachpiece unique. Cutting edge of Blue PaperSteel. With forged ferrule and hoop, the handle is made from selected sandal-wood.Blade length 60 mmOverall length 225 mmBlade thickness 6-7.5 mm

Professional-quality forged chisels from aJapanese master workshop. Ideal forwood joinery and high-precision work.Cutting edge of White Paper Steel.Japanese red oak handles with solid steelhoops.Blade length 60 mmOverall length 225 mmBlade thickness 5-6 mm

No. 718941 378.07 € 449.90 €

No. 710015 62.94 € 74.90 €

No. 710016 104.96 € 124.90 €

No. 710790 96.55 € 114.90 €


32

A OIRE NOMIExtra-long handle and oiled surface:

1 Single chiselsBlade width3 mm No. 710320 26.81 € 31.90 € 6 mm No. 710321 26.81 € 31.90 € 9 mm No. 710322 27.65 € 32.90 € 12 mm No. 710323 29.08 € 34.60 € 15 mm No. 710324 29.24 € 34.80 € 18 mm No. 710325 32.69 € 38.90 € 21 mm No. 710326 33.53 € 39.90 € 24 mm No. 710327 36.05 € 42.90 € 30 mm No. 710328 37.73 € 44.90 € 36 mm No. 710329 39.41 € 46.90 € 42 mm No. 710330 40.25 € 47.90 €

6-piece set6-piece set in a leather tool roll:6/9/12/18/24/30 mmNo. 710331 204.96 € 243.90 €

2 10-piece set10-piece set in a leather tool roll:3-36 mmNo. 710332 331.85 € 394.90 €

B TATAKI NOMIReady to use, ideal for beginners:Well-crafted chisels with durable double-layered blades (milled steel). Waxed han-dles of Japanese red oak, with pre-fittedsteel hoops.Blade length 58 mmOverall length 225 mmBlade thickness 5-6 mm



2 10-piece set10-piece set in a leather tool roll:3-42 mmNo. 710791 162.02 € 192.80 €

D

C HATTORI® CHISEL SETSGreat value-for-money Japanese chiselsmade of milled steel (double-layered, 60Rockwell) in a kiri-wood case. Handlesmade of Japanese red oak. Blade length 58 mmOverall length 225 mmBlade thickness 5-6 mm

6-piece set6/9/12/18/24/30 mm

1 10-piece set3/6/9/12/15/18/24/30/36/42 mm

Set up tips:Nomi do not come ready to use (ex-cept the HSS models and TatakiNomi). They must first be sharpenedand finished. We recommend usingJapanese waterstones. For high-preci-sion applications, the back of theblade should also be flat-tened prior to use. This canbe done using a steel plateand SiC powder or a dia-mond stone. The ferrule onthe butt end of the handleshould also be driven downprior to use so that thehammer only makes con-tact with the wood whenstriking the chisel. Detailedinstructions are includedwith every chisel.

D HSS CHISELS FOR CABINETMAKERSExtremely resilient:


6-piece set6-piece set in a leather tool roll:6/9/12/18/24/30 mmNo. 718940 226.81 € 269.90 €


Price advantage

Price advantage

Price advantage

Price advantage

Price advantage

Price advantage Price advantage

Price advantage

1 2 1 2

A

C

1 2

B

1

These chisels are hand-made in a Japan-ese master forge and have a cutting edgeof specially developed, modified YC3steel. The extra-long handle of Japanesewhite oak optimally absorbs impact andits oiled surface provides a verycomfortable grip.Blade length 60 mmOverall length 250 mmBlade thickness 5-6 mm

For heavy-duty restoration, joinery andfurniture-making work. Made from HighSpeed Steel (HSS), which has an ex-tremely fine carbide structure, these toolshave a very sharp edge. Very hard (app-rox. 66 Rockwell) and tough, these chis-els are able to withstand the roughhandling which is often unavoidable in aworkshop. They can even be sharpenedwith a dry grinding machine withoutcompromising the hardness of the steel.The extra-long handles are made ofJapanese red oak and have pre-fitted,forged steel hoops. Ready to use.Blade length 60 mmOverall length 240 mmBlade thickness 5-6 mm

No. 718868 133.61 € 159.00 €

No. 710106 248.66 € 295.90 €

No. 710268 235.21 € 279.90 €


33

B TAPERED CHISELSChisels with tapered blade, ideal for undercutting in joinery and for cleaningcorners. Cutting edge of White PaperSteel. The handles are made of Japanesered oak and have forged steel hoops.Blade length 60 mmOverall length 230 mmBlade thickness 4-7 mm

Blade width6 mm No. 710210 32.77 € 39.00 € 9 mm No. 710211 32.77 € 39.00 € 12 mm No. 710212 32.77 € 39.00 € 15 mm No. 710213 34.71 € 41.30 € 18 mm No. 710214 35.63 € 42.40 € 21 mm No. 710215 36.55 € 43.50 €

A DOVETAIL CHISELSFor light-duty use, e.g. finishing of fingerjoints and dovetails. Thin blades, triangu-lar cross-section, finely ground right tothe edge. Cutting edgeof White Paper Steel.Handles made of Japan-ese red oak.Blade length 55 mmOverall length 225 mmBlade thickness 3.5-6 mm


2 6-piece set6-piece set in a leather tool roll: 3-24 mm

Price advantage

A

1 2

B

Finishing chisels for cabinet work

C PARING CHISELSFor delicate work:



E HATTORI® PARING CHISELS, 5-PIECE SETPerfect tools for smoothing and finishingjoinery. Double-layered, milled steelwith good durability. Handles made ofJapanese white oak. 5-piece set in a kiri-wood case:9/18/24/30/42 mm.Blade length 85 mmOverall length 340 mmBlade thickness 5-7 mm

D CRANKED PARING CHISELSCranked blade madeof White Paper Steelfor cleaning groovesand recessed sur-faces. Triangular blade cross-section.Handles made of Japanese red oak.Blade length 70 mmOverall length 330 mmBlade thickness 7 mm

Price advantage

C

1 2

D E

Painstakingly crafted lightweight pushchisels without ferrules, forged on aspring hammer. Ideal for precision workand for finishing delicate joinery. Theirlong handles allow you to work very accurately with both hands. The bladesmade of White Paper Steel are slightlyangled, so that even deep mortises canbe worked with ease. The handles aremade of Japanese red oak.Blade length 70 mmOverall length 260 mmBlade thickness 3-4.5 mm

Blade width9 mm No. 710156 70.25 € 83.60 € 15 mm No. 710157 73.87 € 87.90 € 18 mm No. 710158 77.23 € 91.90 € 24 mm No. 710159 85.46 € 101.70 €


34

A EXTRA-WIDE CHISEL

No. 715410 436.97 € 520.00 €

B HSS CHISELSRobust and razor-sharp:Ideal for joinery and on-site restorationwork. These powerful chisels made of extremely hard HSS steel offer excellentsharpness and a long edge life. Very hard (approx. 66 HRC) and tough, these chisels are able to withstand the rough handling which is often unavoidable in aworkshop. Even sharpening on dry grindingmachines is possible without compromisingthe hardness of the steel. The extra-longhandles are made of Japanese red oakand have pre-fitted, forged steel hoops.Ready to use.Blade length 80 mmOverall length 290 mmBlade thickness 6-8 mm

1 Single chiselsBlade width15 mm No. 718871 48.66 € 57.90 € 24 mm No. 718872 52.44 € 62.40 € 30 mm No. 718873 56.05 € 66.70 € 42 mm No. 718874 65.04 € 77.40 € 48 mm No. 718875 73.87 € 87.90 €

3-piece set3-piece set in a leather tool roll:15/24/30 mmNo. 718870 167.23 € 199.00 €

2 5-piece set5-piece set in a leather tool roll:15/24/30/42/48 mmNo. 718869 305.88 € 364.00 €

C HATTORI® CARPENTER'S CHISELS, 4-PIECE SET

No. 710850 133.61 € 159.00 €

D MORTISE CHISELS (ATSU-NOMI)Hand-forged in a master workshop:Hand-forged, solid mortise chisel ofWhite Paper Steel with extra-long handle,ideal for deep mortises. With its blue-annealed steel ferrule, the slim blade seam-lessly joins the long handle. A forgedsteel hoop protects thewood, even against thestrongest forces. Blade length 95 mmOverall length 295 mmBlade thickness 10-13 mmBlade width12 mm No. 718973 79.41 € 94.50 € 18 mm No. 718974 90.59 € 107.80 € 24 mm No. 718975 87.31 € 103.90 €

E MORTISE CHISELSThese heavy chisels are used to make or rework the guides of Japanese slidingdoors (Shoji) and partition walls. The double-layer blade, laminated with WhitePaper Steel, has a square cross-sectionthat is tapered towards the end of theblade and regains its original dimensionjust before the steel ring of the handle.This creates a support area that ensuresguidance even in deep mortises and pre-vents damage to the edge of the hole.Handles made of white oak.Blade length 80 mmOverall length 260 mmBlade thickness 7.5-12 mmBlade width6 mm No. 710175 33.53 € 39.90 € 9 mm No. 710176 35.21 € 41.90 € 12 mm No. 710177 36.05 € 42.90 € 15 mm No. 710178 38.07 € 45.30 € 18 mm No. 710179 39.83 € 47.40 €

Price advantage

Price advantage

A

1 2

B

C

D E

Striking chisels for carpentry work

For making and touchingup large wooden joins, the Japanese temple carpenter needs extra-broadblades. Only a few forgers venture toproduce these formidable tools. TheJapanese master blacksmith Akio Tasaiensures that each broad blade is painstakingly made by hand. This beautifulblade is particularly suitable for finishingjoinery, and for countersinking fittings.The surface of this extra-wide chisel has been worked with a scraper blade. Furthermore, the chisel boasts double-layered steel with a cutting edge of BluePaper Steel, which was forged in a char-coal furnace. Forged ferrule and hoop,Japanese red oak handle, leather case included.Blade width 90 mmBlade length 60 mmOverall length 230 mmBlade thickness 5.6 mm

Four sturdy chisels with extra-long bladesmade of milled steel (double-layered) forjoinery and restoration in carpentry.Handles made of Japanese white oak. In a wooden case: 18/24/30/42 mm.Blade length 85 mmOverall length 295 mmBlade thickness 9 mm

No. 710838 234.45 € 279.00 €

No. 710250 284.87 € 339.00 €

Chisels || Japanese type, Hybrid chisels

35

Finishing chisels for carpentry work

A TASAI SHINOGI NOMI

B SLICKHand-forged slick for making beam jointsand for finishing work. Double-layered,well-proportioned blade with a cuttingedge of White Paper Steel. Handle madeof Japanese red oak.Blade width 54 mmBlade length 120 mmOverall length 580 mmBlade thickness 12 mm

C HATTORI® SLICKSWell-proportioned, well-balanced slickswith double-layered blades (milled steel)and a long edge life. The handles aremade of Japanese white oak.Blade length 120 mmOverall length 580 mmBlade thickness 12 mmBlade width42 mm No. 710825 57.98 € 69.00 € 54 mm No. 710823 66.39 € 79.00 €

No. 710802 129.33 € 153.90 €

Hybrid chisels D DAMASCUS HYBRID CHISELS, 6-PIECE SETJapanese steel quality - Western bladeform:

E HYBRID CHISELS WITH LONGBLADES, 6-PIECE SETSharpened for use, reinforced hoop.

No. 710287 142.77 € 169.90 €

A

B C

D E

The blades of 24-layer Damascus steel(Suminagashi), laminated with BluePaper Steel (approx. 61 HRC), have out-standing endurance, even on the hardestwoods. With its integral design, the heftyhandle of Japanese red oak, with a strongheavy-duty ferrule, transmits the highestimpacts to the blade. The blades aresharpened and readyfor use, not angledand have a flat back(not hollow-ground). Set of 6 in kiri-woodcase (6/12/19/25/32/38 mm).Blade length 65 mmOverall length 210 mmBlade thickness 7 mm

These chisels are hand-made in small batches by Japanesemaster blacksmith Akio Tasai. All materi-als used radiate elegance, and the un-compromisingly functional details reflectthe depth of experience in the manu-facture of these tools. The blade madefrom Blue Paper Steel is forged with atriangular profile, allowing joints to be re-worked without damaging the edges. Thedouble-hollow back of the blade reducesfriction and makes trueing the extremelyhard cutting edges easy. Annealing theforged steel ferrule to 300°C gives it ametallic blue shimmer with the effect ofan ageless link between the handle andthe neck of the blade. To complete thishigh-quality tool, the master uses a darktagayasan handle which, thanks to itsheavy weight, perfectly balances theforged blade. Blade width 36 mmBlade length 95 mmOverall length 375 mmBlade thickness 6-11 mm

Hybrid chisels are a hybrid form of West-ern design and Japanese technology. Theycombine the benefits of both tool culturesand are designed for craftsmen who appre-ciate the Japanese construction but don'twant to forego the Western design.

These chisels come in a completely Wes-tern design with a long blade of vana-dium-alloyed steel for high durability(approx. 61 HRC). Due to its integral de-sign, the long, hefty handle of Japanesered oak with a strong hoop transmitseven the highest impact. The back of the

blade is flat (not hollow-ground).A cotton canvas tool roll protectsthe chisels when not in use.6 chisels (6/12/19/25/32/38 mm).Blade length 95 mmOverall length 255 mmBlade thickness 3-5 mm

No. 700960 115.04 € 136.90 €

No. 730030 113.45 € 135.00 €

Chisels || Western type

36

Western type

Striking chisels

A PFEIL® CHISELSTraditional quality:

1 Single chiselsBlade width4 mm No. 700950 13.19 € 15.70 € 6 mm No. 700951 13.19 € 15.70 € 8 mm No. 700961 13.36 € 15.90 € 10 mm No. 700952 13.36 € 15.90 € 12 mm No. 700953 14.03 € 16.70 € 16 mm No. 700954 14.45 € 17.20 € 20 mm No. 700956 15.88 € 18.90 € 26 mm No. 700957 18.07 € 21.50 € 30 mm No. 700958 19.24 € 22.90 € 32 mm No. 700959 19.58 € 23.30 € 35 mm No. 700962 21.76 € 25.90 € 40 mm No. 700963 23.45 € 27.90 €

2 6-piece set6 piece set in an elegant beechwood case:6/10/12/16/20/26 mmNo. 700997 112.61 € 134.00 €


3 12-piece set12-piece set in a leather tool roll: 4-40 mmNo. 700965 226.81 € 269.90 €

B ALL-METAL CHISELS, 4-PIECE SETNothing is impossible with these chisels:

No. 701016 67.14 € 79.90 €

Finishing chisels

C PFEIL® PARING CHISELS, 6-PIECE SET

D PFEIL® MINI CHISELS SETHandy and neat:

No. 700994 70.59 € 84.00 €

Price advantage

Price advantage

Price advantage

A

1 2 3

These robust tools are not only great forreworking timber joints, but are alsosuited for occasional prying and forevening plaster. Their red colour meansthey can be identified and found withease. The high chromium content and ahardness of 60-62 HRC at the cuttingedge make for a strong and reliable tool.The neck and tang are made of softersteel to cushion hammer blows.Set comes in a robust tool roll.Blade widths 25/30/35/40 mmBlade length 125-145 mmOverall length 300-360 mmBlade thickness 5.5 mm

B

C

D

Precision-made chisels with a traditionaldesign. Forged from a chrome/vanadiumsteel alloy, heat-treated in an electric fur-nace, then ground and polished by hand.The high quality of these chisels is exem-plified by their uniform hardness (approx.60 HRC) and homogeneous fine mirrorpolish. The blades come pre-sharpened,ready to use, and fitted with unvarnishedhornbeam handles.Blade length 120-140 mmOverall length 260-280 mmBlade thickness 2.5-4.5 mm

These perfectly shaped paring chisels ofchromium/vanadium steel, hardened toapproximately 60 HRC, are ideal for fin-ishing wood joints. With its oval shape,the octagonal oiled elm-wood handle pro-vides a comfortable, non-slip grip. Its tra-pezium profile, created by the bevelledsides, means you can use the chisel inmortises or for finishing dovetails withoutdamaging the edges. Comes in a tool roll.Blade length 100 mmOverall length 265 mmBlade thickness 3-5 mm

These compact chisels made ofchrome/vanadium steel (60 HRC) allowyou to work very closely and precisely onthe workpiece. They are therefore idealfor cleaning up fittings, fine wood jointsand all other kinds of detailed work andcan also be used for sculpting. Sphericalhandles made of smoked native robiniawith brass ferrule, hand-polished bladesand a maple wood storage block makethis set a real eye-catcher. An ideal giftfor people with a passion for wood.Blade widths 6/12/19/25 mmBlade length 60 mmOverall length 150 mmBlade thickness 3-5 mm

No. 700996 55.13 € 65.60 €

No. 701158 42.77 € 50.90 €

Chisels || Western type, Chinese chisels

37

C CROWN® CORNER CHISEL

Chinese chisels

Rugged HSS blades in a simple design.These Chinese chisels won't let youdown, even under rough treatment inrestoration and joinery work or whenworking on hard composite materials and glue joints.

D CHINESE HSS CABINETMAKER'SCHISELS

1 Single chiselsBlade width12.5 mm No. 700980 7.48 € 8.90 € 19 mm No. 700981 8.40 € 10.00 € 25 mm No. 700982 8.74 € 10.40 € 31 mm No. 700983 9.66 € 11.50 € 38 mm No. 700984 10.17 € 12.10 €

2 5-piece set5-piece set, in a cotton tool roll:12.5/19/25/31/38 mmNo. 700985 48.40 € 57.60 €

E CHINESE HSS BROAD CHISELS 1 Single chiselsBlade width40 mm No. 700991 8.40 € 10.00 € 50 mm No. 700986 9.24 € 11.00 € 63 mm No. 700987 11.01 € 13.10 € 75 mm No. 700988 12.77 € 15.20 € 90 mm No. 700990 14.54 € 17.30 €

2 5-piece set5-piece set, in a cotton tool roll:40/50/63/75/90 mm

Price advantage Price advantage

C

D

1 2

E

1 2

A CROWN® MINI CHISELS

4-piece set4-piece set, in a fine wooden case:6/12.5/19/25 mmNo. 701150 79.75 € 94.90 €

1 7-piece set7-piece set, in a fine wooden case:6/10/12.5/16/19/22/25 mmNo. 701170 142.77 € 169.90 €

A

1

B CROWN® SKEW CHISELS

Bevel1 Right No. 701152 15.88 € 18.90 € 2 Left No. 701153 15.88 € 18.90 €

B

1 2

For right-angled finishing of corners andmortises. Precisely milled blade made ofcarbon-steel (55 HRC), rosewood handle.Cut length 10 x 10 mmBlade length 110 mmOverall length 255 mm

Single-bevelled, skew-ground chisels, madeof alloyed tool steel (approx. 58 HRC).Rosewood handles.Blade width 13 mmBlade length 135 mmOverall length 295 mmBlade thickness 5 mm

Compact chisels allow you to get close tothe workpiece and give you precise handcontrol. Ideal for cleaning up fittings andwood joints. Polished blades made of al-loyed tool steel (approx. 58 HRC). Rose-wood handles with solid brass ferrules.Blade length 50-60 mmOverall length 150 mmBlade thickness 5-6 mm

Extra-hard HSS steel (64 HRC) forheavy-duty applications and working onwearing materials. The slightly taperedblades reach corners and undercuts eff-ortlessly. Fine-grained handle made ofChinese hardwood.Blade length 105 mmOverall length 230 mmBlade thickness 4 mm

These extra-broad chisels are perfect forlarge-scale carpentry, restoration andsculpture work. The front portion of thespade-shaped blade is made of HSSsteel (64 HRC) and is hard-soldered tothe body via a transitional metal layer.Durable handle made of fine-grained Chi-nese hardwood with a naturally seasonedsurface.Blade length 80 mmOverall length 240 mmBlade thickness 4 mm

Chisels || Tool rolls and accessories

38

Tool rolls and accessories

For safely storing chisels and carvinggouges.

A LEATHER TOOL ROLLMade of fine-quality leather. The seamsare reinforced with rivets.

B COTTON TOOL ROLLSHeavy fabric with shaped pockets forchisels, gouges, screwdrivers, spanners,pliers etc. Includes belt with snap fas-tener.

C ROLLUP CASE

D LEATHER PROTECTIVE CAPS FORCHISELSFor Japanese chisels with a blade lengthof up to approx. 60 mm. Fine-qualityleather.For blade width3/6/9 mm No. 715150 3.28 € 3.90 € 12/15/18 mm No. 715151 3.36 € 4.00 € 21/24/30 mm No. 715152 3.53 € 4.20 € 36/42 mm No. 715153 3.78 € 4.50 €

A

B

C

D

Chiselling tips:

Place the workpiece on asolid base to minimiserebound when struck (ifpossible, do not clampin a bench vice). Strikethe chisel exactly in linewith the direction of thecut to maximise preci-sion and power.

When mortising throughthe entire thickness of apiece, start by making V-shaped cuts from thecentre of the mortise out-wards, until half the thickness has beenremoved. Then work from the oppositeside. The back of the blade faces thecentre of the mortise.

Leave the edge of themortise rough, then, withthe back of the bladefacing the edge, cleanthe edge until it is thedesired width. When cut-ting large mortises, pre-drilling the mortise mayhelp you obtain resultsmore quickly. Use an iron hammer todrive Japanese Nomi (e.g. Genno 375 g).Use a wooden mallet or leather hammerfor all other chisels.

Start chiselling across the grain withheavy blows; finish by chiselling alongthe grain with lighter blows.If the chisel becomes jammed, carefullydislodge it by gently shaking and pullingit out of the wood to prevent the edgefrom breaking out or bending.

Oil the blade occasionally to reduce fric-tion during use. A Japanese Aburatsubo(e.g. No. 713810) is ideal for this.

1

1

1

1 6 pocketsMax. tool length 270 mmOuter dimensions 370 x 290 mmNo. 717501 25.13 € 29.90 €

6 pocketsMax. tool length 300 mmOuter dimensions 370 x 320 mmNo. 717502 26.81 € 31.90 €




1 5 pocketsMax. tool length 240 mmOuter dimensions 310 x 400 mmNo. 712900 7.48 € 8.90 €


Strong, impregnated cotton fabric rollupcase. Belt with snap fastener. As thetools can only be inserted from one side,and are secured by a flap, they cannotfall out. Max. tool length 260 mm

1 6 pocketsOuter dimensions 400 x 430 mmNo. 707513 7.48 € 8.90 €

9 pocketsOuter dimensions 560 x 430 mmNo. 707514 10.00 € 11.90 €

12 pocketsOuter dimensions 710 x 430 mmNo. 707515 12.52 € 14.90 €

39

Carving and sculpting tools | 42

European carving tools | 42

Japanese carving tools | 47

Traditional Chinese carving tools | 47

Special tools | 48

Carver’s mallets | 49

Carving knives and xylography tools | 49

European type | 49

Japanese type | 52

Swedish type | 53

Drawknives | 54

Sculptor’s axes | 54

Adzes | 55

The extension of the artist’s arm!

Sculpting tools

40

Creating a sculpture with axe and chisel

from a trunk is surely one of the most intense

experiences that woodcraft has to offer.

Not only the creative act itself, but intimate

contact with this unique natural material,

exploring its organically grown structure, and

the unforgettable odour of freshly cut wood

all make sculpture a unique experience.

In this creative process, the tool must be

the extension of the artist’s own arm. Over a

period of time, a heartfelt relationship develops

between the sculptor and the tool. When the

tool lies comfortably in the hand, when the

balance is right, when there is long-lasting

sharpness, then mind and body work together

creatively. The sculptor’s trust in »his« tool

brings creativity to fruition.

Owing to their complex form and the com-

bined requirements of long-lasting sharpness

and lightness of weight, the manufacture of

gouges is one of the most difficult challenges

of blacksmithing. Today, the Swiss »Pfeil®«

brand, with a wide range of products present-

ing the main part of our offering, is regarded

as the leading manufacturer. These are the

proven standard tools for sculptors and wood

carvers - developed through intensive ex-

change with professionals and with a consis-

tantly high level of quality.

We also offer hand-forged Japanese gouges

with two-layer blades, having a long edge life

and excellent sharpness. These are stronger

and shorter than European gouges and,

thanks to their head hoop, well suited for

hammering.

Our Chinese cutting tools, which we obtain

from traditional small blacksmith workshops,

are unique in Europe. They are distinguished

not only by their favourable price, but also by

GOOD TOOLS BRING CREATIVITY TO FRUITION

their good steel quality and the conical shape

of their blades - particularly advantageous for

deep reliefs, cut-outs and under-cuts.

The tools from Sweden, a country where four-

year-olds are already engaged in wood carving,

are especially convincing in terms of their

fine profiling and ergonomic grips.

TYPES

Gouges

Gouges are the classical sculptor’s tools.

Their curvature is described by sweep num-

bers (from 2 = very flat to 11 = very strongly

curved). We recommend, for example, the

basic assortment of the 12-part »Pfeil« set

No. 700890.

Chisels

These have a cutting edge ground obliquely

or at a right angle. By contrast with normal

wood working chisels, they are sharpened on

both sides. Due to their versatility for use

with edges, contours, peripheries, surfaces

and inscriptions, they are a must in every

basic set.

V-parting tools

These have a V-shaped cross-section and

are used for cutting sharp-edged grooves,

outlining patterns, and carving letters.

Cranked tools

Curved or cropped tools are advantageous

for elaborating concave surfaces, recesses or

relief backgrounds. The narrower the work

situation, the greater the tools cropping

required. Besides these basic types, there

are also a number of special tools forms, with

which one can add on considerably to the

basic assortment according to project.

SHARPENING

Sharpening on rapidly rotating grinding or

polishing wheels is in fact in widespread use

- nevertheless, we recommend the traditional

method of sharpening on water stones or on

the Tormek wet grinding machine. This gives

longer edge life, as the cutting edges are not

heated, and ensures a more exact cutting

edge geometry without rounding off the be-

vels. You will find additional information on

the sharpening of sculptors’ tools in our

Sharpening Primer, which you can order

under www.more-than-tools.de

EXPERT TIPS ON THE USE OF SCULPTINGTOOLS

Use a lager-sized gauge with mallet for the

crude composition of sculputures or reliefs.

To make things easier, imagine the geometrical

shape underneath the surface, e.g. the eye as

a ball, the neck as a cylinder, etc.

Always work your way from the highest point

(e.g. the nose) to the back. This gives you the

opportunity of making corrections if neces-

sary by moving the form slightly backwards.

Define your reference points (e.g. centre

of the head, tip of the nose, elbow, etc.)

These should be best marked with a cross.

Sculpting tools

41

Try to work evenly on every part of the object

in order to retain a well-balanced overall

picture.

Always make sure to fasten your workpiece

properly (e.g. with the help of carver’s screw)

in order to avoid injuries and any

disturbances of the working process.

Which tools are recommended for beginners?

For sculpting figures:

Allongee Gouge, sweep 7, blade width

50 mm (for rough material removal and large

workpieces)

Sweep 3, blade width 35 / 40 mm (clean-up)



Smaller widths of different sweeps for detail

work depend on the workpiece.

These tools are also used for our »Sculpting

Figures« workshop.

For relief work:

Compact carving tools from Pfeil, see page 46

Pfeil carving knives, see page 49

Power Grip carving tool set, No. 710258

For hollowing out troughs or bowls:

Trough-Maker's Adze, sweep 5, No. 706066

Pfeil Scorp Gouge, size 2, No. 700702

Pfeil Sculptor's Gouge, short-bent version,

see page 43.

How do I select a gouge?

There are three criteria:

1.) the sweep

2.) the blade width (measured perpendicular

to the blade (also with 1S)

3.) the longitudinal form of the blade

What do I do if I have a gouge but am not

satisfied with my choice?

First, decide which of the three criteria are

fine and don't need to be corrected. If, for

example, the sweep is fine but the blade is

not wide enough, stick with the sweep

number but choose a wider blade. If both the

sweep and the blade width are fine, but you

cannot get the cut you need with a straight

gouge, choose the short-bent version for

shallow recesses and the long-bent version

for deep ones.

TIPS

For beginners in woodcarving, we recommend

wearing the »ProHands« protective gloves for

unclear or difficult working situations.

NEW

Sharpening pass

Two free sharpenings (see page 2).

Sharpening service


products (see page 2).

Courses to this subject

Introduction to Sculpting

Sculpting of Figures

Relief Carving

You will find a number of interesting work-

shops for sculptors in our current workshop

programme, which you can order cost-free

from DICK, www.more-than-tools.de.

Working on surfaces with different sweeps

results in different surface structures, which

means they can also be used to produce

variations in design. The larger the sweep,

the more noticeable the structure.

Sweep 7 Sweep 5 Sweep 7 Sweep 3Chisels

Sculpting tools || Carving and sculpting tools

42

European carving tools

PFEIL® CARVING TOOLSThe exceptionally durable and wear-resistant carving tools from the Swisscompany Pfeil are not only well-knownamong experts. With over 700 forms andsweeps, Pfeil offers the largest and mostvariable product range. The products ofthe world’s leading manufacture of finecarving tools are made from specially al-loyed, hard tool steel, forged and groundon precision machines, heat-treated inan electric furnace and sharpened byhand ready-for-use. The blades are uniformly hardened to 59-61 Rockwellalong their entire length, the break-proofoiled ash handles are mounted with inner

A FLAT CHISELS, STRAIGHT, DOUBLE BEVELStraight chisels are preferred for letter-ing, but are also suitable for chip carvingand for smoothing straight or slightlyconvex surfaces in figure sculpting. Theskewed variant can be drawn across thesurface and cuts into corners more easily.

Sweep 1, straight cutBlade width2 mm No. 700800 15.04 € 17.90 €3 mm No. 700801 15.04 € 17.90 €5 mm No. 700802 15.04 € 17.90 €8 mm No. 700803 15.04 € 17.90 €10 mm No. 701220 16.72 € 19.90 €12 mm No. 700804 16.72 € 19.90 €16 mm No. 700805 16.72 € 19.90 €20 mm No. 700806 19.75 € 23.50 €25 mm No. 700807 21.76 € 25.90 €35 mm No. 700808 29.33 € 34.90 €40 mm No. 700763 30.17 € 35.90 €

Sweep 1S, skew cut2 mm No. 700810 15.04 € 17.90 €3 mm No. 700811 15.04 € 17.90 €5 mm No. 700812 15.04 € 17.90 €8 mm No. 700813 15.04 € 17.90 €12 mm No. 700814 16.72 € 19.90 €16 mm No. 700815 16.72 € 19.90 €20 mm No. 700816 19.75 € 23.50 €

B GOUGES, STRAIGHTGouges are used for anything from roughwork to shaping to finishing, and are therefore the most versatile sculptor'stools. If necessary, each of these gougescan also be used the other way round towork on convex surfaces.The 11-sweep tools, which take you fromgouge to V-parting tool, are often used tocreate shape transitions.

Sweep 2Blade width5 mm No. 701223 15.04 € 17.90 €8 mm No. 701224 15.04 € 17.90 €12 mm No. 700818 16.72 € 19.90 €16 mm No. 701355 16.72 € 19.90 €20 mm No. 700820 19.75 € 23.50 €30 mm No. 700819 26.81 € 31.90 €

Sweep 33 mm No. 700821 15.04 € 17.90 €5 mm No. 700822 15.04 € 17.90 €8 mm No. 700823 15.04 € 17.90 €10 mm No. 701226 16.72 € 19.90 €12 mm No. 700824 16.72 € 19.90 €16 mm No. 700825 16.72 € 19.90 €20 mm No. 700826 19.75 € 23.50 €

A

B

25 mm No. 700827 21.76 € 25.90 €30 mm No. 700828 26.81 € 31.90 €35 mm No. 700829 29.33 € 34.90 €40 mm No. 700765 30.17 € 35.90 €

Sweep 4Blade width20 mm No. 701356 19.75 € 23.50 €

Sweep 53 mm No. 700830 15.04 € 17.90 €5 mm No. 700831 15.04 € 17.90 €8 mm No. 700832 15.04 € 17.90 €10 mm No. 701227 16.72 € 19.90 €12 mm No. 700833 16.72 € 19.90 €16 mm No. 700834 16.72 € 19.90 €20 mm No. 700835 19.75 € 23.50 €25 mm No. 700836 21.76 € 25.90 €30 mm No. 700837 26.81 € 31.90 €35 mm No. 700838 29.33 € 34.90 €40 mm No. 700766 30.17 € 35.90 €

Sweep 620 mm No. 701357 21.76 € 25.90 €



Sweep 92 mm No. 701232 15.88 € 18.90 €3 mm No. 700858 15.88 € 18.90 €5 mm No. 700860 15.88 € 18.90 €7 mm No. 700861 15.88 € 18.90 €10 mm No. 700862 17.06 € 20.30 €13 mm No. 701233 17.06 € 20.30 €15 mm No. 700863 20.08 € 23.90 €20 mm No. 701234 21.18 € 25.20 €25 mm No. 700864 21.18 € 25.20 €30 mm No. 700859 26.81 € 31.90 €

Sweep 110.5 mm No. 701235 17.23 € 20.50 €1 mm No. 700868 17.23 € 20.50 €2 mm No. 700867 17.23 € 20.50 €3 mm No. 700865 17.23 € 20.50 €7 mm No. 701238 17.23 € 20.50 €10 mm No. 700866 18.07 € 21.50 €15 mm No. 700869 21.76 € 25.90 €18 mm No. 701239 23.45 € 27.90 €

B GOUGES, STRAIGHT

ferrules. Only indigenous woods and solvent-free oils are used.

Your advantage: Quick delivery straight from stock3-year quality guarantee!

Standard Pfeil carving tools (p. 42 - 45)Overall length 250 mmBlade length 120 mm


43

B SCULPTOR'S GOUGES, LONG BENT FORMThe long bent form is used in curved recesses to allow you to cut out of thepiece from the deepest point without damaging the edges of the recess.

Sweep 7LBlade width14 mm No. 700710 18.40 € 21.90 €20 mm No. 700884 22.27 € 26.50 €25 mm No. 700885 22.61 € 26.90 €35 mm No. 700711 32.69 € 38.90 €

Sweep 8L10 mm No. 700715 19.75 € 23.50 €18 mm No. 700886 22.27 € 26.50 €30 mm No. 700716 30.17 € 35.90 €

Sweep 12L (V 60°)3 mm No. 700720 20.92 € 24.90 €6 mm No. 701254 20.92 € 24.90 €10 mm No. 700721 21.76 € 25.90 €

B

C SCULPTOR'S GOUGES, SHORT BENT FORMSimilar to the long bent form, these gouges are also used for deep, curvedshapes. The even stronger bent of thegouge allows you to carve transitions ineven deeper areas and to create small radiuses and arches.

Sweep 7ABlade width6 mm No. 700887 15.88 € 18.90 €10 mm No. 701261 16.72 € 19.90 €14 mm No. 700880 16.72 € 19.90 €18 mm No. 701262 20.08 € 23.90 €25 mm No. 700881 20.08 € 23.90 €

Sweep 8A7 mm No. 700700 15.88 € 18.90 €10 mm No. 700882 16.72 € 19.90 €18 mm No. 700883 20.08 € 23.90 €25 mm No. 700701 21.43 € 25.50 €

Sweep 11A2 mm No. 700705 17.56 € 20.90 €4 mm No. 700706 17.56 € 20.90 €7 mm No. 700707 17.56 € 20.90 €

Sweep 12A (V 60°)3 mm No. 700725 17.56 € 20.90 €8 mm No. 700726 19.24 € 22.90 €

D BACK BENT, INSIDE BEVELPrimarily used for convex shapes and cy-lindrical profiles which cannot be workedon with a turned straight gouge becauseof the strong curve.

Sweep 25Blade width6 mm No. 700736 20.08 € 23.90 €10 mm No. 700738 20.08 € 23.90 €13 mm No. 700737 20.08 € 23.90 €

E DOG-LEG GOUGEThis gouge is used to clear the ground ofdeep, shouldered areas to their finaldepth and to rework corners.

Sweep 21Blade width6 mm No. 700728 17.56 € 20.90 €12 mm No. 700729 17.56 € 20.90 €

F DRAGON GOUGEThis strongly bent gouge is ideal for deeprecesses and for finishing corners, lettering and ornaments.Straight bevel.

Sweep 21 GBlade width5 mm No. 700689 18.91 € 22.50 €

C

D

E

Sweep 12 (V 60°)Blade width3 mm No. 700870 17.56 € 20.90 €4 mm No. 701242 17.56 € 20.90 €6 mm No. 700871 17.56 € 20.90 €8 mm No. 701243 19.24 € 22.90 €10 mm No. 700872 20.08 € 23.90 €

Sweep 13 (V 90°)3 mm No. 700876 17.56 € 20.90 €6 mm No. 701245 17.56 € 20.90 €8 mm No. 700877 19.24 € 22.90 €

Sweep 14 (V 55°)6 mm No. 700703 17.56 € 20.90 €8 mm No. 700873 20.08 € 23.90 €

Sweep 15 (V 45°)3 mm No. 700874 18.40 € 21.90 €6 mm No. 700875 19.75 € 23.50 €

Sweep 16 (V 35°)3 mm No. 700878 18.91 € 22.50 €6 mm No. 700879 20.59 € 24.50 €

Sweep 22, winged V-parting tool6 mm No. 700730 25.97 € 30.90 €12 mm No. 700731 28.49 € 33.90 €

Sweep 23, macaroni tool6 mm No. 700760 21.43 € 25.50 €

A V-PARTING TOOLS, STRAIGHTV-parting tools are popularly used in relief carving to delimit areas. Another important use is the cutting of even grooves.

A

F

Carving tools are often struck with a carver´s mallet. Carver´s mallets page 49

See our Workshop Programme or ourwebsite at www.more-than-tools.de/work-shops for sculpting and carving courses.


44

A FISHTAIL GOUGES, THIN BLADEThanks to their conical form, fishtail gouges are used for backcutting in reliefcarving and for general finishing work.Their projecting corners make it easy tocut within narrow recesses, in which theangle of the gouge can still be corrected.

Sweep 3FBlade width6 mm No. 700740 17.23 € 20.50 €12 mm No. 700741 18.07 € 21.50 €16 mm No. 700742 20.59 € 24.50 €

Sweep 5F8 mm No. 700745 17.23 € 20.50 €14 mm No. 700746 18.07 € 21.50 €20 mm No. 700747 20.59 € 24.50 €



B ALLONGEE GOUGESWith an extra-hard hornbeam handle andheavy-duty ferrule, this gouge is designedfor rough shaping with the mallet andcan resist even the toughest impact.Blade length 140 mmOverall length 300 mm

B

A

C PFEIL® CARVER’S SET WITH ASH HANDLESThe standard version of the carver´s setsare supplied with characteristic oiled handles made from light ash.

1 Pfeil® carver’s set with ash handles,8-piece set8 standard carving tools as professionalbasis equipment for quality-consciousbeginners. Delivered in a roll-up case. Sweep 9/4mm; sweep 7/10 mm; sweep 5/12 mm;sweep 4/20 mm; flat chisel 12 mm; V-tool 8 mm; flat pointed 12 mm; chip carving knife form 12. Ash handles.No. 700896 158.82 € 189.00 €

C

2 Pfeil® carver’s set with ash handles,12-piece setSet of 12 Pfeil carving tools for medium-sized figures, lettering and fine orna-ments, compiled by the Sculptor`sSchool in Brienz. In a robust roll-up case. Sweep 1 (flat)/8mm; sweep 1 (flat/skew)/8 mm; sweep5/8 mm; sweep 5/20 mm; sweep 7/6 mm;sweep 7/14 mm; sweep 8/4 mm; sweep9/10 mm; sweep 12 (V 60°)/6 mm;sweep 8 A/10 mm; sweep 7 L/20 mm.Ash handles.No. 700890 214.20 € 254.90 €

1

Pfeil® carver’s set with ash handles, 25-piece setWith these 20 sculptor’s tools plus accessories you are perfectly equippedfor a wide range of challenging carvingprojects: sweep 1 (flat)/16 mm; sweep 1 S (flat/skew)/16 mm; sweep 2/20 mm;sweep 3/3 mm; sweep 3/12 mm; sweep3/25 mm; sweep 5/35 mm; sweep 7/20mm; sweep 8/7 mm; sweep 8/18 mm;sweep 8/25 mm; sweep 9/7 mm; sweep9/15 mm; sweep 11/10 mm; sweep 11/2mm; sweep 12 (V 60°)/10 mm; sweep14 (V 55°)/8 mm; sweep 15 (V 45°)/3 mm;sweep 8 A/18 mm; sweep 7 L/25 mmplus Brienz chip carving knife, 2 Arkansas sharpening stones, grinding oiland wooden carver’s mallet. Ash handles.

With case3 Canvas No. 700898486.55 € 579.00 € 4 Wood No. 700892637.82 € 759.00 €

3

4

2

Sweep Blade width2 60 mm No. 700946 53.70 € 63.90 €5 No. 700947 56.22 € 66.90 €7 50 mm No. 701276 53.70 € 63.90 €7 60 mm No. 700948 57.90 € 68.90 €8 No. 701271 59.58 € 70.90 €9 50 mm No. 700949 54.54 € 64.90 €


45

A PFEIL® CARVER´S SET WITH PLANE TREE HANDLESThese carving sets, with handles made ofoiled plane tree heartwood made exclu-sively for DICK are not just aesthetic butalso hard-wearing. The decorative planetree wood with its slightly red colour isdue to its small annual rings and scat-tered pores very hard and tough andtherefore takes more blows than ashwood. This beautiful wood is also charac-terized by its striped pattern that is a result of the cutting face of themedullary rays.

For stone sculpting tools see our web-shop at www.more-than-tools.de

1 Pfeil® carver´s set with plane treehandles, 8-piece set8 standard carving tools as professionalbasis equipment for quality-consciousbeginners. Delivered in a roll-up case. Sweep 9/4mm; sweep 7/10 mm; sweep 5/12 mm;sweep 4/20 mm; flat chisel 12 mm; V-tool 8 mm; flat pointed 12 mm; chip carving knife form 12. Plane tree handles.No. 730020 166.39 € 198.00 €

2 Pfeil® carver´s set with plane treehandles, 12-piece setSet of 12 Pfeil carving tools for medium-sized figures, lettering and fine orna-ments, compiled by the Sculptor`sSchool in Brienz. In a robust roll-up case. Sweep 1 (flat)/8 mm; sweep 1 (flat/skew)/8 mm; sweep5/8 mm; sweep 5/20 mm; sweep 7/6mm; sweep 7/14 mm; sweep 8/4 mm;sweep 9/10 mm; sweep 12 (V 60°)/6 mm;sweep 8 A/10 mm; sweep 7 L/20 mm. Plane tree handles.No. 730021 217.65 € 259.00 €

Pfeil® carver´s set with plane tree handles, 25-piece setWith these 20 sculptor’s tools plus accessories you are perfectly equippedfor a wide range of challenging carvingprojects: sweep 1 (flat)/16 mm; sweep 1 S (flat/skew)/16 mm; sweep 2/20 mm;sweep 3/3 mm; sweep 3/12 mm; sweep3/25 mm; sweep 5/35 mm; sweep 7/20mm; sweep 8/7 mm; sweep 8/18 mm;sweep 8/25 mm; sweep 9/7 mm; sweep9/15 mm; sweep 11/10 mm; sweep 11/2mm; sweep 12 (V 60°)/10 mm; sweep14 (V 55°)/8 mm; sweep 15 (V 45°)/3mm; sweep 8 A/18 mm; sweep 7 L/25mm plus Brienz chip carving knife, 2 Arkansas sharpening stones, grindingoil and wooden carver’s mallet.Plane tree handles.

With case3 Canvas No. 730022494.96 € 589.00 € 4 Wood No. 730023646.22 € 769.00 €

A

1 2

3

4

B PFEIL® »VAL GARDENA« CARVER´S SET, 11-PIECE SETRecommended by professional sculptors: This set of 11 Pfeil carving tools forquick and easy preliminary cutting oflarge figures was put together in coopera-tion with experienced sculptors from theState Vocational School in Gröden (SouthTyrol). Delivered in a practical roll-upcase made of robust »Schwingerhosen-yarn«, with grey felt lining to protect theblades.The set comprises carving tools: sweep 1(flat/skew) 10 mm, 20 mm and 30 mm;sweep 3/35 mm; sweep 4/20 mm; sweep5/12 mm; sweep 7/10 mm and 35 mm;sweep 11/5 mm and 10 mm; ash handles.Carving knife: blade length 55 mm,cherry wood handle.No. 700669 230.25 € 274.00 €

B

C EMPTY ROLL-UP CASESProtect your tools with these roll-upcases made of indestructible »Schwinger-hosen yarn« linen, which is as much admired in Switzerland as leather trousers in Germany. The inside is linedwith grey felt and thus protects the toolsfrom touching each other and keeps awaydust and shavings. Pockets6 No. 700699 27.31 € 32.50 € 8 No. 730024 32.35 € 38.50 € 12 No. 730025 34.29 € 40.80 € 25 No. 730026 79.16 € 94.20 €

C


46

Pfeil® Compact carving toolsPerfect for small objects and intricatework. The shorter blades and slenderhandles make these tools ideal for smallhands performing delicate work.Blade length 90 mmOverall length 200 mm

F PFEIL® COMPACT CARVING TOOLS,4-PIECE SET

No. 700690 46.97 € 55.90 €

G PFEIL® COMPACT CARVING TOOLS,6-PIECE SET700670/71/74/79/84/86. Including abirch and maplewood rack.No. 700691 83.95 € 99.90 €

H PFEIL® COMPACT CARVING TOOLS,12-PIECE SET700670/71/73/74/79/80/82/83/84/85/86/88. Including a birch and maplewoodrack.No. 700692 162.10 € 192.90 €

I PFEIL® COMPACT CARVING TOOLS,18-PIECE SET700670/71/72/73/74/75/76/77/78/79/80/81/82/83/84/85/86/87.In a fine beechwood case.No. 700693 276.47 € 329.00 €

A

F

G H

I

Sweep 1Blade width8 mm No. 700670 12.02 € 14.30 €

Sweep 2Blade width

12 mm No. 700672 13.87 € 16.50 €

Sweep 312 mm No. 701328 13.87 € 16.50 €

Sweep 53 mm No. 700673 13.70 € 16.30 €8 mm No. 700674 13.70 € 16.30 €12 mm No. 700675 13.87 € 16.50 €


Sweep 1S, skew cut8 mm No. 700671 12.02 € 14.30 €

Sweep 7LBlade width10 mm No. 700677 13.87 € 16.50 €


Sweep 8ABlade width7 mm No. 700680 13.87 € 16.50 €

Sweep 95 mm No. 700682 13.70 € 16.30 €10 mm No. 700683 13.87 € 16.50 €


Sweep 12 (V 60°)Blade width2 mm No. 700686 14.20 € 16.90 €4 mm No. 701338 14.20 € 16.90 €6 mm No. 700688 14.20 € 16.90 €8 mm No. 700687 14.20 € 16.90 €

Sweep 15 (V 45°)3 mm No. 701340 14.20 € 16.90 €

A CHISELS, STRAIGHT, DOUBLE BEVEL

B GOUGES, STRAIGHT

C SCULPTOR'S GOUGE, LONG BENT FORM

D SCULPTOR'S GOUGE, SHORT BENT FORM

E V-PARTING TOOLS, STRAIGHT

B

C

D

E

Ideal for anyone who wishes to try theirhand at woodworking. Particularly suit-able for young people and makes a splen-did gift. 700670/79/88 and 700921.


47

Japanese carving tools

As with many other handcraft traditions,the Japanese woodcarving craft has itsorigins in the ecclesiastical sphere. Eventoday, lavishly carved temples and pre-cious family altars as well as the Buddhacarving craft bear witness to the centu-ries of refinement of the sculpting artand of sculpting tools. Japanese sculp-ting and carving tools are characterisedby double-layered blades with excellentsharpness. Their integral design andsturdy ferrules allows them to be struckwith a mallet or hammer.

A SCULPTOR’S TOOLS, 10-PIECE SETThe compact design of these carefullycrafted Nomi from a master workshop inJapan makes them well-suited for deli-cate tasks requiring precision, such aslettering and reliefs. Blades of double-layered steel, core made from Blue PaperSteel, Japanese red oak handles. Gouges:sweep 5/15 mm; sweep 9/9 mm; sweep6/6 mm; sweep 6 cranked/15 mm; flatpoint 15 mm; flat 12 mm; Yariganna, 12 mm; skew chisel, right, 9 mm; V-par-ting tool, 7.5 mm; flat cranked 9 mm. 10-piece set in a kiri wood case.Blade length 20-50 mmOverall length 205-215 mm.No. 714009 334.45 € 398.00 €

B GOUGESThese gouges offer all the quality advantagesof Japanese sculptor’s gouges at a goodprice-performance ratio. Double-layered blades, core made from SK 5, seamlessly integrated handles and a removable heavy-duty head ferrule, which is fitted for use with a hammer. Outside bevel.Blade length 50 mmOverall length 220 mmSweep 7

BW mm6 mm No. 715251 14.20 € 16.90 € 9 mm No. 715252 14.20 € 16.90 € 12 mm No. 715253 14.20 € 16.90 € 15 mm No. 715254 14.20 € 16.90 € 18 mm No. 715255 14.71 € 17.50 € 21 mm No. 715256 15.04 € 17.90 € 24 mm No. 715257 15.29 € 18.20 €

2 7-piece set

No. 715250 111.76 € 133.00 €

Price advantage

Interesting fact:The sweeps of gouges are based on a standard set by the so-called»Sheffield Illustrated List«. Thesweeps are circular segments. Thelarger the sweep, the stronger theconcavity and the larger the arc seg-ment. Thus, for example, sweep 3 de-scribes a very flat concavity; sweep 9describes a complete semi-circle.

Traditional Chinese carving tools

These exceptional carving tools emanatefrom two forges on the southern Chinesecity of Dongyang, a centre of the sculp-ting craft. With the small chisels, the durable blades are sharply tapered into a pointed tang. The larger chisels have asocket-shaped throat which holds thehandle and prevents splitting. The smallchisels are made of carbon-steel (C 60,approx. 58 HRC). The socket chisels areof forged double-layered steel (above 60HRC). In line with Chinese tradition, thechisels are only roughly ground by theblacksmith. It is the user who makes thechisels ready-for-use by fine grinding tothe required sharpness and mounting thehandles.

Note: Due to the purely manual manu-facturing process, the stated dimensionsare subject to relatively wide fluctuati-ons.

Carving a filigree landscape relief. Note how close to the blade the chisel is held.

C CARVING BLADES, 18-PIECE SETLight-duty gouges for relief carving anddetail work. The blades have pointedtangs. Mixture of forms (flat, flat/skew,curved, V). Coarse ground, no handles.Blade width 2-32 mmOverall length 100-120 mmNo. 700970 31.43 € 37.40 €

D CARVING TOOLS, 12-PIECE SETLight-duty gouges with pointed tangs.Chinese hardwood handles. Mixture offorms (flat, flat/skew, curved, V), in cot-ton tool roll.Blade width 5-20 mmOverall length 180-210 mmNo. 700972 88.15 € 104.90 €

E SCULPTING BLADES18-PIECE SETTools for all-purpose carving. The bladeshave socket tangs. Mixture of forms (flat,flat/skew, curved, V). Coarse ground, nohandles.Blade width 3-40 mmOverall length 100-120 mmNo. 700971 62.94 € 74.90 €

F SCULPTING TOOLS, 6-PIECE SETDouble-layer forged gouges with sockettangs. Chinese hardwood handles. Mix-ture of forms (flat, curved, V), in cottontool roll.Blade width 6-18 mmOverall length 180-210 mmNo. 700973 44.12 € 52.50 €

G SCULPTING TOOLS, 12-PIECE SETSpecifications as above. Mixture of forms(flat, flat/skew, curved, V), in cotton toolroll.Blade width 6-25 mmOverall length 180-210 mmNo. 700974 83.95 € 99.90 €

A

B

C

D

E

F

G

1 Single gouges

1 2

7-piece set, in a cotton tool roll:715251-715257


48

G CHINESE LONG-HANDLED GOUGESIdeal for hollowing out drums, deep vessels and large sculptures. The bladesare bevelled on the inside and slightlyangled, allowing more free play for theoak handles. Made of carbon-Steel.Overall length 680 mm

Special tools

A YARIGANNA SPEAR PLANESThe Yariganna is one of the oldest tools forsmoothing wood and is recognised as thepredecessor of the plane in Japan. The free-hand application of this tool allows the userto follow the wood's grain and so producewonderfully organic and tactile surfaces.Can be used on both flat and curved work-pieces. Ideal for decorative panels, reliefsor sculptures.

1 Mokume YarigannaThe wood-like grain ofthe blades gives these Yariganna a special aesthetic. The iron is folded repeatedly and then plated with whitepaper steel and set in a magnolia handle.Blade width 35 mmBlade length 120 mmOverall length 560 mmNo. 710094 276.47 € 329.00 €

2 Two-hand YarigannaFor planing large wooden surfaces in carpentry and sculpting. Core made ofBlue Paper Steel, handle made of tagayasan (rosewood).Blade width 25 mmBlade length 90 mmOverall length 410 mmNo. 710095 167.23 € 199.00 €

3 One-hand YarigannaFor fine sculpting work, instrument making and restoration. Core made ofWhite Paper Steel, tagayasan handle.Blade width 18 mmBlade length 60 mmOverall length 235 mmNo. 710096 57.98 € 69.00 €

B MIKISYOPrecision tool for removing fine shavingor chipping in carving and restorationwork. Made of Blue Paper Steel.Blade width 4 mmBlade length 25 mmOverall length 290 mmNo. 710097 35.29 € 42.00 €

Semi-circular, double-layer blade for hollowing out bowls, chair seats, etc. Core made of White Paper Steel,tagayasan handle. Inside bevel.Blade width 32 mmBlade length 75 mmOverall length 215 mmRadius approx. 16 mmNo. 710812 150.42 € 179.00 €

D PFEIL® SCORP GOUGE, SIZE 1The curved blade is particularly suitablefor bowls and hollow shapes. Where normal gouges can no longer be guidedalong the grain due to lack of space (e.g.in narrow spots), this tool saves the daybecause it is drawn across the surface.Blade width 33 mmOverall length 180 mmNo. 700935 19.24 € 22.90 €

E PFEIL® SCORP GOUGE, SIZE 2

No. 700702 41.60 € 49.50 €

F SICKLE CHISELThis carving tool based on an historicalmodel is produced in a German masterforge. The sickle-shaped blade is suit-able for fine carving of surfaces as wellas for all curved work pieces in boat building and chair making. Made ofspring steel (approx. 59 HRC), turnedash handle.Blade width 45 mmBlade length 250 mmOverall length 400 mmNo. 710310 66.39 € 79.00 €

A

2

3

B

C

D

E

F

G

1

Sweep Blade width4 75 mm No. 700978 23.03 € 27.40 €5 50 mm No. 700976 19.24 € 22.90 €5 62 mm No. 700977 21.18 € 25.20 €9 30 mm No. 701001 24.87 € 29.60 €9 40 mm No. 701002 26.72 € 31.80 €9 50 mm No. 701003 28.66 € 34.10 €

C JAPANESE SCORP GOUGE

This scorp gouge is primarily used forhollowing out large bowls and for chairseats. The hefty cherrywood handle provi-des a comfortable grip and the curved3.5 mm blade can even tackle hardwood.Blade width 70 mmOverall length 235 mmWeight 280 g

Sweep 4

Sweep 5

Sweep 9

Sculpting tools || Carver’s mallets, Carving knives and xylography tools

49

B PLASTIC MALLETThis mallet, made from high-strengthUHMWPE (ultra-high molecular weightpolyethylene) fibre, is extremely wear-re-sistant and relatively light for the largeface diameter. It allows heavy impactwhile reducing vibrations. Thanks to theshorter handle it is ideal for workingstone but can also be used in woodsculpting.Head Ø 100 mmOverall length 240 mmTotal weight 600gNo. 705673 50.34 € 59.90 €

C JAPANESE CARVER’S MALLETTurned from a piece of keyaki wood, ex-tremely robust, high-level impact power.Head Ø 85 mmOverall length 270 mmTotal weight 700 gNo. 714054 26.55 € 31.60 €

D HORNBEAM MALLETS DELUXEThese elegant carving mallets are bothpowerful and well-balanced. The horn-beam heads are turned by a mastercraftsman and set in strong elm handles.The surfaces are primed with linseed oil.

1 Bell-shapedHead Ø 85 mmOverall length 245 mmTotal weight 500 gNo. 730002 20.59 € 24.50 €

2 CylindricalHead Ø 95 mmOverall length 250 mmTotal weight 650 gNo. 730003 24.20 € 28.80 €

E HORNBEAM MALLETSSolid carver’s mallets in traditional Ger-man form, made of hornbeam, one of thehardest indigenous woods. The mortisedshaft is unvarnished.

1 Size SHead Ø 70 mmOverall length 270 mmTotal weight 380 gNo. 730015 10.84 € 12.90 €

2 Size MHead Ø 87 mmOverall length 270 mmTotal weight 540 gNo. 730016 12.18 € 14.50 €

3 Size LHead Ø 120 mmOverall length 270 mmTotal weight 960 gNo. 730017 15.04 € 17.90 €

Carving knives and xylography tools

European type

F PFEIL® CHIP CARVING KNIVESChip carving knives ground and polishedready to use, with fine oiled cherry woodhandles. The form and size are perfectlyaligned for freehand carving of small figures, chamfering and wickerwork.

Carver's mallets

A PFEIL® BRASS MALLETSHighly functional brass mallets from thetraditional company Pfeil, with beautifulcherry wood handles. Their bell-shapedheads enable the mallets to be held closeto the neck in order to finely adjust thestriking power. The mallets are shock ab-sorbing and easy on your arms.

1 Size MHead Ø 47 mmOverall length 200 mmTotal weight 450 gNo. 730018 39.83 € 47.40 €

2 Size LHead Ø 49 mmOverall length 220 mmTotal weight 700 gNo. 730019 45.80 € 54.50 €

A

1 2

B

C

D

1 2

E

1 2 3

F

1 2 3 6 754 8 9 10 13 141211

Form Blade width Blade length Overall length1 1 9 mm 50 mm 190 mm No. 700920 8.82 € 10.50 €2 3 8 mm 35 mm 165 mm No. 700927 7.39 € 8.80 €3 4 13 mm 50 mm 155 mm No. 700923 7.39 € 8.80 €4 6 13 mm 35 mm 145 mm No. 700922 9.75 € 11.60 €5 7 14 mm 40 mm 150 mm No. 700926 7.39 € 8.80 €6 8 18 mm 55 mm 135 mm No. 700928 7.39 € 8.80 €7 10 8 mm 35 mm 135 mm No. 700929 7.39 € 8.80 €8 11 10 mm 45 mm 195 mm No. 700930 8.82 € 10.50 €9 12 11 mm 55 mm 195 mm No. 700931 9.75 € 11.60 €10 13 11 mm 60 mm 195 mm No. 700934 9.75 € 11.60 €

Strong, 2.6 mm thick blade; can be used forfree form carving and as a wickerwork knife.11 14 16 mm 60 mm 200 mm No. 700889 11.43 € 13.60 €

Curved, 2 edges.12 15 12 mm 50 mm 160 mm No. 701282 11.43 € 13.60 €13 »Pfeil« 13 mm 35 mm 145 mm No. 700921 7.39 € 8.80 €

Ash handle.14 »Brienz« 15 mm 70 mm 190 mm No. 700932 11.51 € 13.70 €

G PFEIL® CARVING KNIVES, 4-PIECE SETYou won’t want to put these carving knives down. The ergonomic plumwoodhandles make for excellent control ofthese knives, enabling fine chamferingwork as well as freehand carving of figu-res and small objects. The set contains 4 forms (knives with cambered blade and No. 700999 74.71 € 88.90 €

round backs, large and small, knives withstraight blade large and small). Casemade of »Schwingerhosen yarn«.Blade length 30-45 mmOverall length 160-185 mm

G

Sculpting tools || Carving knives and xylography tools

50

C PFEIL® ABEGGLEN DETAIL KNIFEThis knife has a round and a hollowground blade, which means it can beused for deep cuts but also for cutting ornaments and letters. A hexagonalhandle of oiled acacia wood provides a comfortable, non-slip grip.Blade width 15 mmBlade length 35 mmOverall length 190 mmNo. 730031 23.45 € 27.90 €

D PFEIL® CHILD’S CARVING TOOL »JUNIOR CARVER« Carving is not just great fun for children,it is also has educational value. The child-friendly handle of oiled beechand the short multiform blade of provenPfeil quality make for easy handling. L-form blade.Blade width 16 mmBlade length 55 mmOverall length 140 mmNo. 701500 12.44 € 14.80 €

F PFEIL® SHOULDER KNIVESThe shoulder knife was the most impor-tant veneering tool used from the MiddleAges until the start of the 20th century.Its long handle, which rests on the user'sshoulder, allows the tool to be guidedwith more control and power than a knifeguided solely by hand. Also ideal as chipcarving knife. Ash handle.Blade length 90 mmOverall length 650 mm.

Blade shape1 Straight No. 700893 41.93 € 49.90 € 2 Curved No. 700894 41.93 € 49.90 €

A HERDIM® HSS BLADESThese HSS blades are extremely hard(approx. 65 HRC), tough and resistant towear. They are perfect for working hard-woods, veneers, synthetic materials andlaminates as well as for making smallplanes. The blades are hardened alongtheir entire length, have double bevelsand rounded edges.Overall length 160 mmBlade thickness approx. 1.8 mm

Blade width1 6 mm No. 700371 8.32 € 9.90 € 2 8 mm No. 700373 9.66 € 11.50 € 3 15 mm No. 700375 10.50 € 12.50 €

C

B PFEIL® WOODWORKING KNIVES

Without handleOverall length 160 mmBlade thickness 2 mm

Blade width1 3.5 mm No. 700401 7.73 € 9.20 € 2 6 mm No. 700402 7.73 € 9.20 € 3 9 mm No. 700403 7.73 € 9.20 € 4 12 mm No. 700404 7.73 € 9.20 € 5 15 mm No. 700405 7.73 € 9.20 € 6 19 mm No. 700406 7.73 € 9.20 €

Made of alloyed Swiss steel. Approx. 59-60 Rockwell, double bevel.

7 With rosewood handleOverall length 160 mmBlade thickness 2 mmBlade width3.5 mm No. 700390 13.36 € 15.90 €

6 mm No. 700391 13.36 € 15.90 € 9 mm No. 700392 13.36 € 15.90 €

12 mm No. 700393 13.36 € 15.90 € 15 mm No. 700394 13.36 € 15.90 € 19 mm No. 700395 13.36 € 15.90 €

Self portrait of the inlay makerAntonio Barili(Renaissance)with shoulderknife.

D

F

2

1

2

3

1

B

A

2

3

4

5

6

7

1

E MINI CHISELS, 6-PIECE SETFor fine restoration work and model building. Stainless steel hardened to ap-prox. 50 HRC, coarse finish. 6-piece set.Blade width 3.5-6.5 mmBlade length 10 mmOverall length 140 mmNo. 700430 10.00 € 11.90 €

E


51

A PFEIL® LINOLEUM AND WOOD CARVING TOOLSComfortable in the hand, tools for woodand linoleum carving, reliefs and smallsculptures. Mushroom shaped handlesmade of untreated indigenous pearwood.Blade length 70 mmOverall length 125 mm

25 12-piece setIn a beautiful maplewood storage rack: 1 x no. 700902-1312 tools in a storage rack No. 700899 166.39 € 198.00 €

B PFEIL® WOODCARVING TOOLSThe compact design and the mushroomshaped handles of untreated pearwoodmake these gouges ideal for carvingwoodblocks, small objects, ornaments,chamfering and reliefs.Blade length 80 mmOverall length 140 mm

Sweep Blade width2 B 1 flach 12 mm No. 700790 14.20 € 16.90 €3 B 1S flach/schräg 12 mm No. 700791 14.20 € 16.90 €4 B 3 12 mm No. 700792 14.20 € 16.90 €5 B 5 12 mm No. 700793 14.20 € 16.90 €6 B 8A gekröpft 10 mm No. 700794 14.20 € 16.90 €7 B 9 10 mm No. 700795 14.20 € 16.90 €8 B 12 (V60°) 8 mm No. 700796 14.20 € 16.90 €9 B 7 14 mm No. 700797 14.20 € 16.90 €

Sweep BW mm1 L 1 flach 8 mm No. 700902 12.27 € 14.60 €2 L 1S flach/schräg 8 mm No. 700903 12.27 € 14.60 €3 L 1A flach/gekröpft 8 mm No. 700904 12.27 € 14.60 €4 L 5 8 mm No. 700906 12.27 € 14.60 €5 L 11 3 mm No. 700911 12.27 € 14.60 €6 L 12A (V 60°) 4 mm No. 700913 12.27 € 14.60 €

Sweep BW mm7 L 5 3 mm No. 700905 12.27 € 14.60 €8 L 7 6 mm No. 700907 12.27 € 14.60 €9 L 7 10 mm No. 700908 12.27 € 14.60 €10 L 9 5 mm No. 700909 12.27 € 14.60 €11 L 11 1 mm No. 700910 12.27 € 14.60 €12 L 12 (V 60°) 1 mm No. 700912 12.27 € 14.60 €

Sweep BW mm13 L 8 3 mm No. 700914 12.27 € 14.60 €14 L 8 7 mm No. 700916 12.27 € 14.60 €15 L 9 2 mm No. 700917 12.27 € 14.60 €16 L 11 0.5 mm No. 700918 12.27 € 14.60 €17 L 12 (V 60°) 4 mm No. 700919 12.27 € 14.60 €18 L 15 (V 45°) 2 mm No. 700936 12.27 € 14.60 €

Sweep BW mm19 L 1 flach 4 mm No. 700780 12.27 € 14.60 €20 L 1S flach/schräg 4 mm No. 700781 12.27 € 14.60 €21 L 5 5 mm No. 700782 12.27 € 14.60 €22 L 7 4 mm No. 700783 12.27 € 14.60 €23 L 8A 7 mm No. 700784 12.27 € 14.60 €24 L 11 2 mm No. 700785 12.27 € 14.60 €

Set A6-piece set in a carton. No. 700900 71.85 € 85.50 €Single tools set A

Set B6-piece set in a carton. No. 700901 71.85 € 85.50 €Single tools set B

Set C6-piece set in a carton. No. 700939 71.85 € 85.50 €Single tools set C

Set D6-piece set in a carton. No. 700891 71.85 € 85.50 €Single tools set D

Price advantage

Price advantage

Price advantage

Price advantage

1 Tools Set A, 8-piecein a beautiful maplewood storage rack.1 x No. 700790-7007978 tools in a storage rack No. 700915 108.40 € 129.00 €

Single tools set A

Price advantage

10 Tools Set B, 8-piecein a beautiful maplewood storage rack.Sweep B2/12 mm; sweep B4/12 mm;sweep B7L/12 mm; sweep B8/10 mm;sweep B9/7 mm; sweep B11/7 mm;sweep B15/6 mm; sweep B25/10 mm8 Tools in a storage rack No. 700998 108.40 € 129.00 €

Price advantage

A

1 2 3 4 5 6

7 8 9 10 11 12

13 14 15 16 17 18

19 20 21

22 23 24

B

10

1

2 3 4 5 6 7 8 9

25


52

Japanese type

A CARVING SET, 9-PIECEThe most important tools for carvingsmall objects and reliefs in a functionalroll-up case. Solid carbon-steel blades,approx. 62 HRC, sharpened and ready touse. Fitted with teak handle scales. Bevelled on one side. 9-piece set: knife9 mm; Kiridashi 12 mm and 21 mm;sweep 6/5 mm and 12 mm; flat 10 mm;V 8 mm; saw 75 mm, TS 1.5 mm; filesrough and fine, 52 mm.Overall length 150-190 mmNo. 710742 150.42 € 179.00 €

B CARVING KNIVESExclusive carving knives with ergonomiccambered handles made of untreatedkashi wood for perfect cutting control.Stainless A2 steel (approx. 62 HRC). Bevelled on both sides.Blade length 50-65 mmOverall length 80-195 mm

Blade1 Form A No. 710755 16.13 € 19.20 € 2 Form B No. 710756 16.13 € 19.20 € 3 Form C No. 710757 16.13 € 19.20 € 4 Form D No. 710758 16.13 € 19.20 € 5 Form E No. 710759 16.13 € 19.20 € 6 Form F No. 710762 16.13 € 19.20 € 7 Form G No. 710763 16.13 € 19.20 € 8 Form H No. 710764 16.13 € 19.20 € 9 Form I No. 710765 16.13 € 19.20 € 10 Form J No. 710766 16.13 € 19.20 €

5-piece set5-piece set in a case (A, B, C, D, E).No. 710760 76.64 € 91.20 €

Price advantage

5-piece set5-piece set in a case (F, G, H, I, J).No. 710761 76.64 € 91.20 €

Price advantage

C JAPANESE CHIP CARVING KNIVESMultilayer blades, very sharp and wear-resistant. Handles of Japanese cherrywood. Forms A and B bevelled on oneside, C and D bevelled on both sides.Core made of Blue Paper Steel.Blade length 30 mmOverall length 180 mm

Blade1 Form A No. 710715 14.20 € 16.90 € 2 Form B No. 710716 14.20 € 16.90 € 3 Form C No. 710717 14.20 € 16.90 € 4 Form D No. 710718 14.20 € 16.90 €

A

4-piece setIn a canvas case (form A, B, C, D)No. 710719 53.78 € 64.00 €

Price advantage

D CARVING AND OUTDOOR KNIFEFoldable with locking blade. Handle ofJapanese cherry wood. Right-hand bevel.Core made of Blue Paper Steel.Blade width 25 mmBlade length 100 mmOverall length 230 mmNo. 710705 20.92 € 24.90 €

E CARVING KNIFE WITH CORD HANDLESimilar to the handles of Samuraiswords, the handle of this Japanese car-ving knife is bound with silk cord. Slip-proof in the hand, it can be preciselyguided, even with increased applicationof force. 3-layer blade, core-layer of BluePaper Steel, hand guard, bevelled onboth sides.Blade length 55 mmOverall length 160 mm

Blade1 Curved No. 710747 25.13 € 29.90 € 2 Straight No. 710749 25.13 € 29.90 €

F POWER GRIP CARVING TOOLS, 7-PIECE SETFine tools with thin blades of double-laye-red steel for carving masks, reliefs, wood-blocks and linoleum. The cutting edgesare hardened to 63 HRC and come sharp-ned and ready to use.7-piece set in a gift box: gouge sweep9/3 mm; sweep 9/6 mm; sweep 6/9 mm;sweep 3/9 mm; V-tool, 4.5 mm; straightchisel, 7.5 mm; skew chisel 7.5 mm.Blade length 32 mmOverall length 146 mmNo. 710258 37.39 € 44.50 €

G CARVING TOOLS, 5-PIECE SETFeatherweight and razor-sharp, tradition-ally used in Japan for woodblock, maskand relief carving. The thin blades, forged of double-layer white paper steelcome sharpened and ready to use. Han-dles of magnolia wood. Blade thicknessapprox. 2 mm. Straight chisel 9 mm;skew chisel 9 mm; gouge sweep 9/3 mm;gouge sweep 8/6 mm; V-tool 5 mm. 5-piece set in a kiri wood case.Blade length approx. 30 mmOverall length 210 mmNo. 710741 100.00 € 119.00 €

These small chisels made from SK-5steel are primarily used for detail work in relief carving as well as in restorationwork and model-building. The long, light-weight aluminium handles make themeasy to guide. Very hard (55-60 HRC),fine-ground head shapes.Blade width 3 mmOverall length 140 mm

Blade1 Straight cut No. 710294 11.68 € 13.90 € 2 Skew cut No. 710295 11.68 € 13.90 € 3 Gouge sweep 9 No. 710296 11.68 € 13.90 € 4 V-tool 90° No. 710297 11.68 € 13.90 €

H NANO ONE MINI-CHISELS

B

1 2 3 4 5

6 7 8 9 101

C

2 3 4

D

E

21

F

G

H

1 2 3 4


53

Swedish type

Frost® knivesCutting tools have been forged in theSwedish town of Mora for over 400 years.The Mora Knife, developed by Erich Frostover 100 years ago is synonymous withfunctionality and reliability. The majorityof the blades presented here are forgedfrom rolled 2.5 mm thick traditionaltriple-layered carbon-steel. The knivesare distinguished by their excellentsharpening properties and long edge life(the hardness of the core layer is approx.61 HRC). To preserve the steel's finegrain structure, alloys have not beenadded, meaning that the blades are notrustproof. The birch handles are firmlyattached to the full-length tang.

A ALL-PURPOSE KNIFE # 137A Frost classic for carvers, fishermen andoutdoorsmen. Beautiful leather sheathwith belt loop.Blade length 100 mmOverall length 200 mmNo. 701563 25.13 € 29.90 €

B CARVING KNIFE # 120Ideal for use in woodwork classes:Allround woodwork knife; also suitablefor use in schools due to the compactblade. Plastic sheath included.Blade length 59 mmOverall length 165 mmNo. 701560 15.04 € 17.90 €

C CARVING KNIFE # 106Carving and outdoor knife in the classic,slim Mora design. Plastic sheath.Blade length 79 mmOverall length 190 mmNo. 701567 15.04 € 17.90 €

D CARVING KNIFE # 123Straight cutting edge, particularly wellsuited for chip carving, reliefs and ornamentation.Blade length 58 mmOverall length 185 mmNo. 701565 15.04 € 17.90 €

E CARVING KNIFE # 105Long, slim blade for carving larger pieces. Ergonomically designed handle, without ferrule or sheath.Blade length 79 mmOverall length 200 mmNo. 701561 13.70 € 16.30 €

F CHILDREN’S CARVING KNIFE # 73Besides creativity, carving also requires asense of shape forming and already inchildhood makes the educationally im-portant reference head-hand-material.Give your children access to the creativeactivity of woodworking with this carvingknife, which is specially designed for achild's hand. Carbon-steel, birch handlewith hand guard. Riveted leather sheathwith a handle strap.Blade length 73 mmOverall length 165 mmNo. 701564 23.87 € 28.40 €

Hook knives for hollowing spoons,bowls and other concaved surfaces.

G HOOK KNIFE # 162Double edged bevel.Curvature radius approx. 14 mmBlade length 50 mmOverall length 160 mmNo. 701568 19.24 € 22.90 €

H HOOK KNIFE # 163Double edged bevel.Curvature radius approx. 22 mmBlade length 61 mmOverall length 160 mmNo. 701566 19.24 € 22.90 €

I HOOK KNIFE # 164Single edged bevel left (standard).Curvature radius approx. 12 mmBlade length 50 mmOverall length 160 mmNo. 701562 17.56 € 20.90 €

B

Svante DjärvSvante Djärv’s carving tools, springhammer-forged from Uddeholm steel, represent a revival of traditional Swedish knife making. The textured, Nordic-ash handles fit comfortably in the hand.

J SVANTE DJÄRV SKEDKNIV HOOKKNIFEWith a curved blade for hollow forms.Curvature radius approx. 10 mmBlade length 40 mmOverall length 145 mm

Bevel1 left No. 701571 45.63 € 54.30 € 2 right No. 701573 45.63 € 54.30 €

K SLÖJDKNIV CARVING KNIFEUniversal carving knife, ash handle withriffled surface.Blade length 60 mmOverall length 165 mmNo. 701570 45.21 € 53.80 €

L BARNTÄLJKNIV CHILDREN’S CARVING KNIFEThe handle is designed for small hands,with integrated hand-guard. Short, strongblade.Blade length 50 mmOverall length 145 mmNo. 701574 42.61 € 50.70 €

SCHNITZEN LERNEN FÜR KIDSBy Robin Edward Trudel. Carving is afascinating handcraft.It trains the fine motorskills, the concentra-tion and the conscious-ness of form. After a brief description oftools and a basic intro-duction to wood carv-ing, each chapter isdevoted to one age group respectively.Step-by-step illustrations provide motiva-tion and precise working instructions atthe same time. This simple introductionto carving makes the reader want more!96 pages, 342 coloured illustrations,hardcover, 170 x 240 mm. In German.No. 713852 20.56 € 22.00 €

A

Hans KarlssonCarving tools by Hans Karlsson withfinely forged blades and ergonomic han-dles. Blades of »Uddeholm Arne« toolsteel (62 HRC). The ash handles aretreated with natural linseed oil.

M TRAGSKAV INSHAVEDrawknife for hollowing out bowls,troughs and chair seats. The U-shapedhandle can be custom fitted by the user.Blade width 65 mmOverall length 170 mmapprox. sweep 5No. 701511 134.37 € 159.90 €

N SPOON GOUGEWith fine forged, cranked and curvedblade, for making spoons, ladles andsmall bowls.Blade width 13 mmBlade length 42 mmOverall length 120 mmNo. 701537 36.39 € 43.30 €

SCHWEDISCHE SCHNITZ-SCHULEWorking with knivesand axes, by WilleSundqvist. This bookby the great Swedishsculptor is character-ised by his love ofwood and the carvingtradition of his home-land. 216 pages, 334 illustrations and photographs,hardcover, 215 x 235 mm. In German.No. 713125 30.65 € 32.80 €

C

D

E

F

G

H

I

J

K

L

M

N

1

2

By Chris Pye. This book presents 10 carving projectsranging from a carvedcopy of Dürer’s well-known painting of supplicating hands toa leaping frog. Eachproject is described indetail, from the initialidea to the finishedwork. Pye’s experience as a carving in-structor allows him to thoroughly addressall the practical questions which arise inthe planning and execution of each project.By Chris Pye; 165 pages,309 photo-graphs, 29 b/w illustrations, softcover,210 x 275 mm, in English.No. 713318 14.86 € 15.90 €

ELEMENTS OF WOODCARVING

Sculpting tools || Drawknives, Sculptor’s axes

54

Drawknives

The drawknife is invaluable for boatbuilders, coopers, wainwrights and chairmakers alike. It can be used for trimmingand finishing straight and curved workpieces, as well as for rounding andchamfering.

A GRÄNSFORS® DRAWKNIFEWell-designed hand-forged drawknifewith bow-shaped, slightly camberedblade. Beech handles mounted in forgedferrules and screwed to the cranked, full-length tangs.Blade length 300 mmBlade width 36 mmOverall length 560 mmNo. 705985 108.40 € 129.00 €

B PFEIL® DRAWKNIFE, ARCHED SLIGHTLY CONCAVETraditional drawknife with slender,slightly convex blade for delicate work.Protective goat leather case.Blade length 240 mmBlade width 25 mmOverall length 430 mmNo. 700966 58.74 € 69.90 €

C PFEIL® HEAVY DRAWKNIFE, STRAIGHTWith its powerful straight blade, thisdrawknife is suitable for removing sub-stantial amounts of wood. Large handleswith screwed tangs. Protective goat leather case.Blade length 250 mmBlade width 33 mmOverall length 430 mmNo. 700967 96.55 € 114.90 €

D SVANTE DJÄRV DRAWKNIFELightweight drawknife for delicate work.Straight, hand-forged blade with texturedash handles.Blade length 135 mmBlade width 20 mmOverall length 265 mmNo. 701569 61.76 € 73.50 €

E PFEIL® MINI-DRAWKNIVESDrawknife with sturdy blade. Cherry woodhandle.

1 Straight handlesBlade length 120 mmBlade width 22 mmOverall length 310 mmNo. 700938 25.97 € 30.90 €

2 Cranked handlesBlade length 110 mmBlade width 22 mmOverall length 280 mmNo. 700937 28.74 € 34.20 €

F ARNAUD® DRAWKNIVESFrench drawknife made of carbon-steelwith cranked ball handles of red beech.Leather blade guard.Blade length 145 mmBlade width 32 mmOverall length 340 mm

StraightNo. 709995 31.01 € 36.90 €

Arched, slightly convex(Upward bending approx. 8 mm)No. 709996 31.01 € 36.90 €

Arched, slightly concave(Downward bending approx. 8 mm)No. 709997 31.01 € 36.90 €

Tips on the use of drawknives:

Pull the drawknife with the bevel tothe bottom at a slant to the workpiece. This makes for better controland reduces the cutting force. Forfine material removal you can achievebetter control by placing both thumbson the blade. For work after scribingand heavy material removal, it is ad-visable to first make several cutsclose up to the scribe line and thento cut to size with continuous strokes.

A

B

C

D

E

1

F

2

Sculptor’s axes

G GRÄNSFORS® SCULPTOR’S AXEIdeal for roughing out and fine detailwork on bowls and sculptures. Featurescurved cutting edge with flat bevel andpointed toe. Textured handle.Head weight 900 gBlade length 120 mmOverall length 370 mmNo. 705964 86.55 € 103.00 €

H TÄLJYXA CARVING HATCHET BY SVANTE DJÄRVWell-proportioned, handcrafted carvinghatchet.Head weight 315 gBlade length 70 mmOverall length approx. 310 mmNo. 701572 87.31 € 103.90 €

For more sculptor’s axes, see theAxes and Hatchets section.

Used with care, the sculptor´s axe willallow you to create the most detailedand expressive of forms.

G

H

Sculpting tools || Adzes

55

Adzes

The adze has always been an importantand highly versatile tool for carpenters,cabinet makers, boat builders and sculp-tors alike, and different versions havetherefore evolved for different purposes.They are used for hollowing-out oftenlarge objects such as troughs, smoothing,and other large-scale carving projects.The most important detail of a good adzeis the right combination of form andlength of the handle, which must suit the shape of the head. But also the bevelmust be customised for the individualapplication. An inside bevel allows theadze to be applied precisely, while anoutside bevel drives the blade quickly out of the wood again for rough work. All our adzes are made of carbon-steel.

Flat adzesFlat adzes are used to flatten and smoothplanes. These planes may be finishedlater or keep their characteristic hewnsurface. Therefore these adzes usuallyhave an inside bevel.

A PFEIL® TWO-HANDED FLAT ADZE,SWEEP 1Robust, drop-forged adze with untreatedash handle. Inside bevel for precise cut-ting action due to straight contact surface.Blade width 75 mmOverall length 460 mmTotal weight 1000 gNo. 700941 62.61 € 74.50 €

B ONE-HANDED FLAT ADZE,SWEEP 3Hand-forged:This flat adze is hand-forged in free formin a German smithy, based on a designby our master sculptor. The head has aslight curve (sweep 3), which makessmoothing surfaces easier. Inside bevelfor precise cutting action due to straightcontact surface. Optimally curved headshape. Handmade handle of oiled ash. Blade width 60 mmOverall length 400 mmTotal weight 620 gNo. 706065 109.16 € 129.90 €

Two-handed gouge-shaped adzesGouge-shaped adzes have a wide rangeof applications and are suitable for hol-lowing out chair seats and boats as wellas for sculpting. The longer handle allowsyou to work large pieces that are fixed tothe floor. Two-handed adzes are oftenused for tiring work in which the secondhand is a welcome support. The secondhand also provides more impact.

C PFEIL® TWO-HANDED GOUGE-SHAPED ADZE, SWEEP 7Robust, drop-forged adze with untreatedash handle. Inside bevel for precise cut-ting action due to straight contact surface.Blade width 70 mmOverall length 460 mmTotal weight 1000 gNo. 700942 71.34 € 84.90 €

D TWO-HANDED GOUGE-SHAPEDADZE, SWEEP 8Hand-forged:This adze, which is hand-forged to ourdesign in a German smithy, has an insidebevel which allows precise applicationbecause the contact surface is not an-gled. The wide, slightly curved blade pro-duces a wonderfully fine surface and istherefore ideal for smoothing. Optimallycurved head shape. Handmade, handle of untreated hickory.Blade width 80 mmOverall length 555 mmTotal weight 1000 gNo. 708358 184.03 € 219.00 €

A

B

C

D

E

E GRÄNSFORS® TWO-HANDED GOUGE-SHAPED ADZE, SWEEP 7Hefty hand-forged adze with an extra-long handle, ideal for hollowing chairseats while standing up. The chair seat isfixed to the floor, the feet are positionedto the left and right of it and the adze isswung through the legs. Outside bevelcombined with a slight inside bevel forrough material removal. This drives the

blade quickly out of the workpiece again.Handle of oiled hickory.Blade width 70 mmOverall length 640 mmTotal weight 1500 gNo. 701585 191.60 € 228.00 €

Sculpting tools || Adzes

56

Trough-maker's adzesThese classic one-hand, hammer-forgedadzes are produced to the specificationsof a master sculptor, who also attachesthe handles. They have an ideal shapefor carving out troughs and large bowls.Their light weight also makes them suit-able for wood sculpting. Oiled ash handles.

E TROUGH-MAKER’S ADZE,SWEEP 5Hand-forged:Hand-forged in Germany to a design ofour master sculptor. With its light weightand specially shaped curved handle, thisadze is ideal for carving out deep vesselssuch as troughs and bowls. The benthandle helps to protect your wrist whileworking and allows narrow strokes. Insidebevel for precise cutting action due tostraight contact surface. Handmadehandle of oiled ash.Blade width 60 mmOverall length 280 mmTotal weight 600 gNo. 706066 117.56 € 139.90 €

F TROUGH-MAKER’S ADZE,SWEEP 7Hand-forged:This small one-handed adze has beenforged based on an old model and is atrue rarity. The strongly curved handle isideal for easily carving out narrow bowlsand deep troughs. The adze, which ismanufactured to a design of our mastersculptor, has a high sweep and largewidth, which also makes it ideal forsmoothing surfaces. Inside bevel for precise cutting action due to straightcontact surface. Handmade handle ofoiled ash.Blade width 80 mmOverall length 210 mmTotal weight 990 gNo. 706053 125.21 € 149.00 €

One-handed gouge-shaped adzesOne-handed gouge-shaped adzes are particularly suitable for detail work anduse close to the body, such as hollowingout bowls, sculpting or working on chairseats on the workbench.

A PFEIL® ONE-HANDED GOUGE-SHAPED ADZE, SWEEP 8Small drop-forged one-handed adze withuntreated ash handle. Inside bevel forprecise cutting action due to straightcontact surface.Blade width 50 mmOverall length 275 mmTotal weight 600 gNo. 700944 71.34 € 84.90 €

B KARLSSON ONE-HANDED GOUGE-SHAPED ADZE, SWEEP 6

No. 701510 152.10 € 181.00 €

C GRÄNSFORS® ONE-HANDED GOUGE-SHAPED ADZE, SWEEP 8Small hand-forged one-handed adze witha combined inside/outside bevel forrough material removal. This bevel drivesthe blade quickly out of the workpieceagain and prevents the adze gettingstuck. The head has an optimally curvedshape and the textured handle of oiledhickory provides a non-slip grip.Blade width 60 mmOverall length 240 mmTotal weight 750 gNo. 701584 158.82 € 189.00 €

D ONE-HANDED GOUGE-SHAPEDADZE, SWEEP 8Hand-forged:This one-handed adze, hand-forged tothe design of our master sculptor, is im-pressive in its flexible handling and soliddesign. The two shaped hand rests onthe hand-made handle allow you toquickly change from rough material re-moval to fine detail work (with your handclose to the head of the adze). Ideal forall kinds of sculpting. Inside bevel forprecise cutting action due to straightcontact surface. Handmade handle ofoiled ash.Blade width 70 mmOverall length 400 mmTotal weight 860 gNo. 706052 104.96 € 124.90 €

Trough-maker´s adzes are suited best for hollowing out troughs and large bowls.

A B C D

E F

Handy, hand-forged Swedish adze with a low sweep for rough material removal.Outside bevel combined with a slight in-side bevel to drive the blade quickly outof the workpiece again. Optimally curvedhead shape. Handle of oiled ash.Blade width 50 mmOverall length 225 mmTotal weight 600 g

57

The oldest known toolsfor woodworking

57

Forest hatchets and axes | 59

Splitting hatchets and axes | 60

Splitting wedges | 61

Garden hatchets | 61

Outdoor and all-purpose hatchets | 62

Tools for carpenters and cabinetmakers | 63

Accessories | 64

Axes and hatchets

58

TYPES: There are three basic types to be

distinguished:

Axes and hatchets for cutting

These tools cut the wood fibres, e.g. for

chopping down trees, removing branches,

or notching. As a rule, such tools have slender

double-bevelled blades with a relatively

pointed cutting angle to enable

easy breaking into the wood.

Axes and hatchets for splitting

These tools split wood along the direction

of the fibres, e.g. for chopping firewood,

shingles, split boards, or poles. As a rule,

such tools have thick and heavy double-

bevelled blades with a relatively blunt

cutting angle for high splitting efficiency.

Axes and hatchets for cutting and splitting

These tools are used for the trimming and

smoothing of workpieces and for the production

of beams, poles, wood for construction, and

wooden joints. As a rule, such tools have

slender one-sided bevelled blades. Typical

examples are the classic broad axes.

SHARPENING: As axes are mostly used outside the workshop,

a mobile sharpening device such as the DMT

folding diamond sharpener (No. 705391) is

recommended.

It has two

different grits

and is extremely

wear-resistant.

You lay the blade

of the axe on a solid support, such as

a tree trunk, and guide the sharpener with

uniform strokes transversely to the cutting

edge, while maintaining the bevel angle.

THE VERY FIRST TOOLS!

Gränsfors Bruks®

Under the motto »An axe is as good as its

smith«, the Swedish company Gränsfors

Bruks has been manufacturing top-quality

axes for over 100 years. Gränsfors axes are

forged by experienced specialists whose skill

is evident in the precision of the tools they

make, which renders any refinement unne-

cessary. This distinguishes Gränsfors axes

from industrially manufactured axes. The

unadulterated, smithied surface shows the

skills of the blacksmith and thus the quality

of the axe, which he then marks with his in-

itials. With few exceptions, the blades are

made of carbon-steel and hardened to 56-57

HRC. The axe handles, made of best hickory

wood, are secured in the axe head with two

wedges, and feel comfortable from the first

touch. The harmony of shape, weight and

length make working with Gränsfors axes a

pleasure. Gränsfors’s 20-year quality guaran-

tee proves their confidence in the durability

of their products. Each axe comes with a set

of instructions and

a solid leather

sheath.

Japanese axes

With their laminated forged blades, consi-

sting of an impact-absorbing soft iron body

with a hard carbon-steel cutting insert (58-

60 HRC), Japanese axes are the epitome of

durability and sharpness. There are two basic

types of traditional Japanese axe heads: Ono

axes have a wide beard and a narrow throat,

making them excellent for smooth ing wood.

The concentration of mass towards the cut-

ting edge improves stability and control du-

ring use. They can also be used one-handed,

holding them close to the throat. Yoki have a

slender, long head, making them best suited

for separating and splitting work. Their

handels are made from unvarnished Japanese

white oak. All come with a protective sheath.

Aberl®

Since the 17th century the Smithy Aberl

has been known for forging and making fine,

traditional tools. Its guiding principle is

simple and effective: You don't have to

reinvent the wheel to make great tools.

All tools made by the family-owned Smithy

Aberl, which is already in its 11th generation,

are made using the same methods as

hundreds of years ago – tried and true! They

are made of hard and very tough carbon-steel

and, unless otherwise specified hardened to

56-57 HRC. Entirely specified, handmade

handles of hickory make these the perfect tools.

DICK® axes and hatchets

The art of creating good hand tools is to

base them on old models that have proven

effective over the years at the height of their

development. Very often, the further develop-

ment of tools after this point only served to

simplify their manufacture and save costs –

at the expense of their ergonomics and

efficiency of use.

Working closely with our master carpenter,

we are now developing tools again that have

proven their efficiency and durability. Our

tools are made in small German forges which

are still skilled in the old techniques. All

heads are forged of carbon-steel. The hickory

or ash handles are made and set by hand.

NEW

Sharpening pass


Sharpening service

Free lifetime sharpening for premium


Workshops

Cutting Out Gutters and Water Conduits

Setting Tool Handles by Hand

Shingle Cutting

No. 708354 166.39 € 198.00 €

No. 717920 32.69 € 38.90 €No. 708357 154.62 € 184.00 €

No. 708356 166.39 € 198.00 €

No. 701594 120.17 € 143.00 €

Axes and hatchets || Forest hatchets and axes

59

Forest hatchets and axes

(Manufacturer instructions, see page 58)

A GRÄNSFORS® FORESTRY AXECurved cheeks for cutting fresh, resinous wood. Long shafts for extra strength and power.

1 Small forest axeFor light-duty forest work, limbing trees and making firewood.Head weight approx. 700 gBlade length 80 mmOverall length 500 mmNo. 705973 57.98 € 69.00 €

2 Forest axeFor limbing felled trees.Head weight approx. 900 gBlade length 90 mmOverall length 670 mmNo. 705961 63.03 € 75.00 €

B GRÄNSFORS® FELLING AXESLarge axe, traditional American design,for chopping and limbing trees. The slender blade with small wedge angledrives deep into the wood, while theS-curved butted shaft makes work effortless. With solid leather sheath.Head weight approx. 1500 gBlade length 110 mm

C GRÄNSFORS®

DOUBLE-BITTED LOGGING AXEAxes featuring a cutting edge on eachside of the head were already the tools of choice for Canadian loggers 100 yearsago. Not only do two cutting edges allowyou to work for longer periods of timewithout interruption but the edges can be sharpened to different bevel anglesdepending on the application (smallangle for maximum cutting performance,large angle for heavy-duty use). Straighthandle with thicker butt end.Note: Not approved for commercial use.Head weight 1600 gBlade length 150 mmOverall length 890 mm

F ABERL® FOREST HATCHETHand-forged:This hatchet is especially suited for cutting off smaller limbs and is an idealcompanion for all outdoor activities andforestry. The handmade and ergonomically shaped hickory handlemakes it a pleasure to use.Overall length 380 mmBlade length 115 mmHead weight 900g

E ABERL® WERDENFELSER FOREST AXEHand-forged:This axe is extremely comfortable to hold and is especially suited for light-duty forestry work, such as removingbranches from the stem of a felled tree.The handmade, ergonomically shapedhickory handle allows fatigue-free working.Overall length 680 mmBlade length 135 mmHead weight 1000 g

D ABERL® MALLET AXEHand-forged:Because of its heavy, flat-ground butt, thisaxe is often used by professional lumber-jacks to drive in felling wedges. The mas-sive, robust blade is perfectly suited forremoving branches of felled trees. The er-gonomically curved, handmade hickoryhandle allows hours of fatigue-free workand, thanks to its length, gives extra driveto the axe head. Approx. 54-55 HRC.Overall length 790 mmBlade length 130 mmHead weight 1700 g

G BARK SCRAPER (KAWA MUKI)Japanese drawknife for removing barkand smoothing logs. Wear-resistant steelblade, handle of Japanese white oak.Blade length 120 mmBlade width 45 mmOverall length 730 mm

A

1

2

B

1

2C

D

E

F

G

1 Short-handle chopping axeOverall length 800 mmNo. 705987 95.80 € 114.00 €

2 Long-handle chopping axeOverall length 900 mmNo. 705988 100.00 € 119.00 €

No. 701661 91.43 € 108.80 €

For splitting medium and thick cross-sections and driving in wedges. Thehighly convex head guarantees maximumsplitting power. The three-layerblade with a hard carbon-steelcore (58-60 Rockwell) is alsosuitable for shredding work. Hasa large hardened striking surface.900 mm long, unvarnished shaftof Japanese white oak.Head weight 1500 gBlade length 120 mmOverall length 900 mm

Axes and hatchets || Splitting hatchets and axes

60

Splitting hatchets and axes

B GRÄNSFORS® SPLITTING HATCHETIn spite of its small size, this splittingaxe has great splitting power with itsweighty, 1000 g, highly convex head. Its handy shape makes it ideal for smallto medium rounds and making logs for firewood. The hickory shaft, which is textured at the base for better grip, canalso be used one-handed if necessary.Head weight 1000 gBlade length 70 mmOverall length 480 mmNo. 701592 66.39 € 79.00 €

A GRÄNSFORS® SPLITTING AXESThe thick heads of these axes have wide flaring cheeks and progressively increasing wedge angles to ensure maximum splitting power. The shaft has an iron sheath to protect it from wear and is textured at the end to provide a more secure grip.

1 Large splitting axeFor splitting medium and large rounds.Head weight 2000 gBlade length 75 mmOverall length 700 mmNo. 705962 78.15 € 93.00 €

2 Small splitting axeFor splitting small and medium rounds.Head weight 1000 gBlade length 70 mmOverall length 590 mmNo. 705979 68.91 € 82.00 €

C GRÄNSFORS® SPLITTING MAULHeavy axe for splittinglarge chunks of firewood.The hammer shaped headhas wide flaring cheeks andis used to drive a splittingwedge.Head weight 3200 gBlade length 65 mmOverall length 800 mmNo. 705969 84.87 € 101.00 €

F JAPANESE MINI SPLITTING AXELittle effort – but the effect is striking:Ideal for splitting kindling and small logs. Highly convex elongated head shape, cutting wedge made of White Paper Steel, body of impact-absorbing soft iron.Head weight 400 gBlade length 50 mmOverall length 330 mmNo. 701659 86.13 € 102.50 €

D TRADITIONAL JAPANESE SPLITTING AXEIdeal for chopping firewood:Splitting axe with incredible powerthanks to its elongated, highlyconvex head and long handlemade of fine-grained Japanesewhite oak. The White Paper Steeledge will remain sharp even when splitting knotty hardwood. Double-bevel.Head weight 1300 gBlade length 75 mmOverall length 900 mmNo. 710819 91.43 € 108.80 €

A

H - WERDENFELSER KINDLING SPLITTERSplitting dry pine into kindlings becomesa real pleasure with this tool. Can be mounted on the wall. The not-ches in the wooden base, which is madeof untreated ash, hold any piece of woodsecurely in place. Almost no cutting forceis needed thanks to the long lever.

No. 708359 149.58 € 178.00 €

G GRÄNSFORS® SPLITTING AXE AND DIAMOND WHETSTONE, SETSplitting axe (No. 701592) and DMT fine-grain diamond whetstone (No. 705386)with virtually infinite service life (also per-fectly suited for other cutting tools). Comesin leather case, 111 x 23 x 5 mm.No. 718929 83.95 € 99.90 €

Price advantage

G

Wood-chopping tips:Keep a safe distance to others. Use a wide, heavy chopping blockthat is stable and approximately kneehigh. Any type of wood will do, butoak will last the longest. Place thepiece to be split towards the back ofthe chopping block so that, shouldyou miss it, the axe will hit the blockand not the ground.

Hold the axe by the end of the shaftto make best use of your strength. At the moment it strikes the wood, the axe shaft should be horizontal andyour arms should be almost fully ex-tended.

It is usually easier to split a piece ofwood from its narrower end. To splitknotty or irregularly grown wood, theaxe's edge must be extremely sharp.Always try to strike the centre (themark) of a piece of wood to facilitatesplitting, especially when splitting aknot. If the piece is not split on thefirst strike and the axe gets jammedin the piece, turn it over and strikethe back of the head on the choppingblock.

To split particularly large or irregularlygrown rounds, use wedges. Always usetwo wedges. Start by driving one intothe edge of the round to make a gap.Insert the second wedge into this gapand work alternatively towards thecentre of the round, increasing thegap until the wood is split into twopieces.

E TRADITIONAL JAPANESE SPLITTING AXE

B

C

D

E

1

2

H

F

Approx. 54-55 HRC.Blade length 320 mmOverall length 680 mm2150 g

Axes and hatchets || Splitting wedges, garden hatchets

61

No. 705965 37.82 € 45.00 €

No. 710803 39.41 € 46.90 €

No. 708360 83.19 € 99.00 €

No. 710804 63.78 € 75.90 €No. 701657 109.16 € 129.90 €

Ideal for cutting off bran-ches and roots, for sharpe-ning and trimming posts.Hand-forged in 3 layersfrom best Hitachi steel. Untreated, ergonomicallyshaped Japanese white oakhandle, magnolia wood sheath. Can be attachedto belts.Head weight 600 gBlade length 150 mmOverall length 340 mm

Garden hatchets

G - SICKLE CLEAVERThis tool is designed for clearing undergrowth and containing rank growth.Due to its long cutting edge, you can alsocut thorny wood with up to 2 cm branchdiameter from a safe distance. The hand-made, untreated ashwood handle with itsrounded end allows the tool to be heldfirmly and safely without slipping. Approx. 55-57 HRC.Head weight 750 gBlade length 320 mmOverall length 910 mm

D JAPANESE GARDENING HATCHET(EDAUCHI ONO)High impact:

Japanese Cleavers (Nata)Nata are machete-like axes equippedwith extremely sharp blades forged frommulti-layered steel. In Japan, they aremainly used in the garden for limbingand trimming trees and bushes.

E NATA JIGATACleaver for gardening and forestry. Theblade has a single right bevel, allowingcuts to be made flush to the trunk.Comes with a sheath and belt loop.Blade length 210 mmOverall length 390 mm560 g

F NATA AZUMAGATAThis effective, powerful cleaver evencopes with thick branches. Double-bevel.Can also be used for splitting wood.Blade length 135 mmOverall length 360 mm755 g

Splitting wedges

Inserting the carbon-steel cutting wedgein the white-hot axe head.

A JAPANESE SPLITTING WEDGEEquisitely handmade - worth its price:For chopping tree trunks and large blocksof wood, with hand-forged and hardenedwedge shoe. The fishbone grooves reducefriction resistance and prevent the wedgefrom recoiling. The round shaft of thishardwood wedge, made of Japanesewhite oak, is reinforced with a steel ferrule to prevent the wood insets frombreaking under heavy blows. Replacement wood insets can be orderedat www.more-than-tools.deOverall length 330 mmWidth 70 mmNo. 701663 67.14 € 79.90 €

B GRÄNSFORS SPLITTING WEDGEMaximum splitting power thanks to slight axial twist. Notched faces. We recommend using two wedges for large blocks.Warning:Never strike steel against steel!Width 40 mmLength 240 mm1700 g

C SAFETY SPLITTING WEDGE, MADE OF ALUMINIUM

D E F G

A B

1 2

C

3

In former times axes were used to cut down trees, but nowadays thesehave been replaced by chain saws. Thisrapid development also affected splittingwedges. The oldest models, usually madeof wood, have been replaced by lows-wear splitting wedges made of steel. Now engineering has taken another step:Safety splitting wedges are made fromextremely impact-resistant, forged aluminium. They do not splinter and areno risk for chain saws. At the same timethey are very light and protected againstcorrosion.

1 Twisted splitting wedge with tipBecause of its twisted shape, the wedge angle enlarges while the wedge is beingknocked in. This results in higher splitt-ing forces. The tip is easily applied to thewood and forces itself in. Grooves on theside of the wedge bite into the wood andtherefore prevent the wedge from recoiling.Overall length 230 mmWidth 50 mm900 gNo. 706079 31.01 € 36.90 €

2 Twisted splitting wedgeThe 45° twist allows enlargement of thewedge angle during striking, thus increa-sing the splitting power. Fishbonegrooves prevent the wedge from recoiling.Overall length 220 mmWidth 45 mm850 gNo. 706075 29.33 € 34.90 €

3 Felling and splitting wedgeAn extra-long wedge to fell trees and splitlarge blocks of wood. The scaled surfaceprevents the wedge from recoiling. Stroke height 35 mmOverall length 265 mmWidth 55 mm800 gNo. 706074 25.13 € 29.90 €

Axes and hatchets || Outdoor and all-purpose hatchets

62

This attractive, traditionally hand-forged axe is particularly suited forchopping small logs, trimmingworkpieces or for outdoor use.Thanks to the extremely wear-resis-tant three-layer steel (Blue Paper Steel)and the exposed cutting edges, thislightweight axe is extremely effective.The blade is decorated with Japanese characters. Bronzed surface,the rear has a hardened hammerhead.Handle of Japanese white oak.Head weight 400 gBlade length 85 mmOverall length 390 mm

Originally a workers’ pastime, today axethrowing is a popular Scandinavian sport,which trains both your body and your con-centration. With instructions. Straighthandle (regular butt end).Head weight1600 gBlade length150 mmOverall length750 mm

No. 705967 83.19 € 99.00 €

The head is forged thinnerthan usual, slightly roundedand polished for skinning ani-mals. This axe can be used tohew wood, cut up game andcut through bone. The grip of the handle isnotched for better handling.Head weight approx. 650 gBlade length 80 mmOverall length 475 mm

No. 705960 54.62 € 65.00 €

Handy, lightweight axe withsurprising power, perfect forthe full range of outdooractivities.Head weight approx. 450 gBlade length 80 mmOverall length 360 mm

No. 705989 78.15 € 93.00 €

Outdoor and all-purpose hatchets

A GRÄNSFORS® MINI HATCHETGränsfors Bruks’s smallest axe, perfect for gardening, fishing, trekking or sculpting.Head weight approx. 200 gBlade length 60 mmOverall length 260 mm

B GRÄNSFORS® WILDLIFE HATCHET

C GRÄNSFORS® HUNTER’S HATCHET

E GRÄNSFORS® INDIAN TRADE AXESUniversal application:From the early 17th century, English andFrench explorers carried so-called tradeaxes with them to exchange with the na-tive Americans living in the New World.They were popular amongst the nativeAmericans due to their handy size andversatility in building shelters and tools,general woodworking and slaughteringanimals. The practical plug join betweenthe handle which thickens at the end andthe mortise of the head make it easy todismantle the axes for transport or sharpening. The cutting edge and headare forged from one piece of steel, theash handle is manually fitted.

1 French modelFeaturing a curved, particularly light-weight head and a »shearing« cutting action.Head weight approx. 330 gBlade length 80 mmOverall length 500 mmNo. 701593 163.87 € 195.00 €

2 English modelWith a heavy head and slightly bearded blade.Head weight approx. 500 gBlade length 90 mmOverall length 500 mmNo. 701595 163.87 € 195.00 €

D GRÄNSFORS®

DOUBLE-BITTED THROWING AXE

No. 705971 117.65 € 140.00 €

See www.more-than-tools.de for avideo demonstration of axe throwing.

F JAPANESE HATCHETFrom a Japanese master workshop:

No. 701658 116.72 € 138.90 €

H JAPANESE ALL-PURPOSE HATCHETHandy and compact:Lightweight hatchet for wood-working, outdoors and wood-carving. Tomahawk-shaped headwith a curved blade and hardenedpoll. Double-bevelled face.Head weight approx. 450 gBlade length 75 mmOverall length 330 mmNo. 710821 52.86 € 62.90 €

No. 710807 53.70 € 63.90 €

No. 710806 32.35 € 38.50 €

A

B

C

D

E

1 2

F G

H I

G LARGE JAPANESE ALL-PURPOSE HATCHETHatchet with double bevel andslighly curved edge. Small socketfor increased stability. Thanks tothe single-sided beard, which protects the fingers, this hatchetcan also be held with one handnear the head, for example forfinishing work.Head weight 750 gBlade length 118 mmOverall length 360 mm

I SMALL JAPANESE ALL-PURPOSE HATCHETAll-purpose hatchet with small socket and double bevel. Thanks to the straight edge, it can also beused for trimming and shapingworkpieces. The single-sided beardprotects the fingers when held withone hand near the head.Head weight 530 gBlade length 95 mmOverall length 330 mm

No. 705986 147.06 € 175.00 €

No. 705578 343.70 € 409.00 €No. 701582 322.69 € 384.00 €

Axes and hatchets || Tools for carpenters and cabinetmakers

63

Axes are also suitable for preciselytrimming a workpiece. Make V-shapednotches to the depth of the mark firstand then remove the extra wood fromthe opposite side.

E JAPANESE CARPENTER’S AXEWood crafts in harmony with nature:Carpenter’s axe with curved head,wide beard and narrow throat forjoining work and hewing and trim-ming trunks and beams. Besidesreducing the cutting resistance,the red painted indentation on theblade, which is characteristic ofthis axe type, has a religious significance in Japan. The irregular recess represents the

No. 701662 150.42 € 179.00 €

Tools for carpenters and cabinetmakers

When hewing beams with the righthand, the axe is held as shown in thefigure. Work away from you. If possible, do not chop off the shaving, but use it as a guide for the next stroke.

A round log, fixed to trestles with dogs,being squared with a broad axe. (How? See our workshop programme:courses on hewing logs and joinery)

Two types of axes are traditionally used in joinery:Universal Broad Axes havesymmetrical, double-bevelled blades and straight handles. They are mainly for making wood jointsand notches. Side Axes or Broad Axeshave slightly tilted, single-bevelled bladesand are used for straightening and smooth-ing logs and beams. The mortise is usu-ally angled sidewards to protect theuser's knuckles. Hybrid models also existwhich can be used for both types ofwork.

1 Side axe, single bevelThin blade with a wide beard and a single bevel, slightly tilted blade.Head weight 1300 gBlade length 175 mmOverall length 490 mm

Right bevel(the beam is to the left of the axe)No. 705968 175.63 € 209.00 €

Left bevel(the beam is to the right of the axe)No. 705972 175.63 € 209.00 €

2 Universal broad axe, double bevelIdeally suited for joint work. Specifica-tions as left but with a double-bevelled blade and a symmetrical head.Head weight 1300 gBlade length 175 mmOverall length 490 mm

C GRÄNSFORS DANISH DOUBLE-BEARDED AXEEarly medieval axe with two extra-longbeards, ideal for hewing beams and boatplanks. The head is offset to the left (rightbevel); the handle is slightly curved andtextured for a better grip. The original ison display at the Roskilde Viking Museum.Comes without leather blade sheath.Head weight 1100 gBlade length 370 mmOverall length 600 mm

B GRÄNSFORS® CARPENTER’S AXEThe thin blade and straight edge of thisaxe make it perfect for shaping work pie-ces. The small beard allowsthe axe to be gripped closeto the head.Head weight approx. 700 gBlade length 90 mmOverall length 450 mmNo. 705974 60.50 € 72.00 €

D GRÄNSFORS GOTLAND AXEHandy axe from the Viking period:This axe is a replica of an original Vikingaxe. It is well-suited for shaping woodenequipment, carpentry and sculpting.Hand-forged head with an inserted cuttingedge bit made from high carbon-steel. Double-bevel.Head weight 700 gBlade length 110 mmOverall length 380 mm

fallibility of all man-made creation and isan apology for intervention in perfect anddivine nature. The three-layer forgedblade is bevelled on both sides. Thehandle is made of untreated Japanesewhite oak.Head weight 1000 gBlade length 130 mmOverall length 900 mm

A B

C

D

E

1

A GRÄNSFORS® SIDE AXE AND BROAD AXE, NO. 1900

2

Hewing tips:

Secure the log approx. at knee heightand fasten it using log dogs.

Make notches in the log down to the desired depth every 30 cm (for greenwood) or 50 cm (dry wood).

Always work with the grain.

Use uniform strokes and shearing-typecutting action. The upper body should move in rhythm with the stroke. Use verylittle effort, allowing the weight of theaxe to do the work for you.

The thickness of the shavings removedshould not be more than 0.5 - 1 cm.

A video clip demonstrating hewing tech-niques can be found in the multi-mediasection of our website (www.more-than-tools.de)

Workshops

Cutting Out Gutters andWater ConduitsSetting Tool Handles by HandShingle Cutting

Axes and hatchets || Tools for carpenters and cabinetmakers

64

No. 708364 75.55 € 89.90 €

No. 708363 142.02 € 169.00 €No. 705983 16.72 € 19.90 €

No. 708365 335.29 € 399.00 €

F - MORTISE AXE

C - DOUBLE-BITTED MORTISE AXEThe double-bitted mortise axe, symbol ofthe carpentry trade, is a combination of amortise axe and a mortise chisel and isused to make mortises. An axe-shapedcutting edge, partially ground on bothsides, at one end and a chisel-shapedcutting edge turned 90° and bevelled onthe other, makes this tool highly versa-tile. Both cutting edges become narrowertowards the socket to allow working ofmortises in full depth. Made from carbon-steel.1600 g600 x 460 mmBlade length 45 / 20 mm

E - SPLITTING KNIFEThis splitting knife excels through itsshape, which has been developed andimproved over many centuries. Theturned, untreated handle with cross-wedging is fixed in the conical eye of theiron, and due to its shape is very comfortable to hold. The cutting edge,which is made of carbon-steel with approx. 55 HRC easily splits shinglesand battens. Splitting knives are hit with the rawhidehammer No. 705681.

1 Splitting knife standardBlade length 265 mmWeight approx. 1500 gNo. 708361 73.95 € 88.00 €

2 Splitting knife standard longBlade length 335 mmWeight approx. 1800 gNo. 708362 79.83 € 95.00 €

With practice, very fine shingles can be made with the splitting knife.

Tips for splitting shingles:

Resinous pine as well as oak and ashare well suited for making shingles.Use evenly grown rounds that are atleast 30 cm in diameter, and quarterthem using splitting wedges.Remove the sapwood and the heartwood near the centre.

Use a splitting knife to make radialsplits in the segments (standingyears) of an average thickness of approx. 13 mm. Smooth the surfacesusing a drawknife.

See our workshop program or visitwww.more-than-tools.de/workshops forcourses on splitting shingles.

Suitable hammer (No. 705681) forshingle cutting in chapter Hammers.

D - LOG DOGFor securing logs prior to hewing. 20 mm square bar steel with hardenedcutting edges which are set perpendicular to one another.900 gOverall length 240 mm

No. 708366 52.86 € 62.90 €

A

B

C

D

E F

1 2

Designed by our master carpenter basedon a historical model, this hand-forgedaxe is suitable for trimming wood jointsand mortises. The slightly conically for-ged blade has an even-ground back and aslightly curved bevel. The narrow side ofthe blade is ground evenly to align acrosssurfaces. Untreated ashwood handle.Overall length 405 mmBlade length 55 mmApprox. 1300 g

B - HAMMER HATCHETIdeal for splitting shingles.Hand-forged double-bevel hatchet withnail claw and hammer head for generalcarpentry work. Two safety brackets rein-force the untreated ashwood handle, thuspreventing it from breaking when pullingnails.Overall length 320 mmBlade length 65 mmapprox. 560 g

Forged wedges for setting handles orsubsequent diagonal wedging of axes and hatchets.Width 15-18 mmThickness 5 mm

Length1 40 mm No. 714040 1.60 € 1.90 € 2 62 mm No. 714041 1.60 € 1.90 €

Metal wedges with steps on both sides to prevent the wedge from coming loose.For setting handles or subsequent diago-nal wedging of axes and hatches.Length 37 mmWidth 7-20 mmThickness 5 mm

No. 705585 21.85 € 26.00 €

Accessories

G GRÄNSFORS® SHARPENING STONESandstone with two grains (300/600) forsharpening and finishing. The rubbercase protects the stone when on the goand serves as a handle during use. Canbe used dry or with water. Ø 57 x 23 mm.

H REPLACEMENT WEDGE SETWood and iron wedge.

Shaft length1 Up to 55 cm No. 705970 2.10 € 2.50 € 2 56 cm + larger No. 705939 2.10 € 2.50 €

I REPLACEMENT WEDGES J REPLACEMENT WEDGES, 2-PIECE SET

No. 714042 1.93 € 2.30 €

G

H

1 2

I J

A - BROAD AXEHand-forged broad axe based on a historical model, which, over decades of daily use, has proven the most effective tool for hewing logsand beams. The blade acts as a largerest, which allows ultra-smooth surfaceseven on large beams. The cutting edge is slightly curved, so that only part of theblade penetrates the wood, which alsomakes it easier to work with. The bladehas a single bevel on the side of the pro-jecting head, and is securely set in theash handle with cross-wedges. To protectthe knuckles, the handle, handmade andfitted by a wainwright, is strongly cranked.Overall length 650 mmBlade length 330 mmApprox. 2800 g

Lie-Nielsen® planes | 68

Veritas® planes | 72

DICK® planes | 73

Kunz® planes | 74

Stanley® planes | 75

Anant® planes | 75

Accessories for metal planes | 76

Japanese planes | 76

Traditional chinese planes | 78

Western style planes | 79

Scraper blades | 80

Scrapers and putty knife | 80

6565

Thin shavings - smooth surfaces

WOODEN PLANES

Advantages

- Warm and pleasant to touch

- Gentle to workpiece, no discolouration

of wood

- Light weight prevents tiring

Disadvantages

- High sole wear with heavy loading

- Warping may occur

- Little resilent mass, less-smooth

operation with difficult grains

JAPANESE PLANES

Advantages

- Operated by pulling, giving good control –

gentle to the joints and less tiring

- Smoother operation thanks to thick blade

- High plane-blade quality

Disadvantages

- Take longer to set up (does not apply to

planes with replacement blades)

- Possible warping due to atmospheric

influences (does not apply to planes with

stabilised bodies and replacement blades)

- No mechanical adjustment aids for

plane blade and mouth

METAL PLANES

Advantages

- High wear resistance of sole base

and edge of mouth

- No warping of plane body due to

atmospheric influences

- High momentum: smoother running,

even with difficult grains and knots

- Simple adjustment of plane blade

and usually also of mouth opening

Disadvantages

- Heavier, so tiring for larger planing jobs

- Can rust (not with bronze planes)

a normal frog. The problem was solved quite

simply by changing the angle and direction of

the blade to produce the same cutting angle as

in a bevel-down plane. The bevel-up principle

is less widespread due to the poor quality of

cast iron in the early Stanley planes. Subject

to extreme forces where the blade sits at the

mouth of the sole, the cast iron on these

planes broke easily. Today, however, better

cast iron makes for much more stable plane

bodies that are more resistant to the forces

of »bevel-up« planing.

Advantages and disadvantagesEasily adjustable cutting angle

The major advantage lies in the easily

adjustable cutting angle. Because the bevel

angle on the blade affects the cutting angle,

the plane can be optimised by altering the

bevel angle on the blade - most easily done

with a micro or secondary bevel.

No chipbreaker

The chipbreaker, which usually adds stiffness

to the blade, is missing on bevel-up planes.

Therefore the iron used is much thicker.

Thicker blade

The blade on a bevel-up plane is thicker than

that of a bevel-down plane. This is an advan-

tage, as it leads to smoother surfaces and

chatters less.

Low centre of gravity

Also an advantage is the low centre of gravity,

which is created by the low-angle frog.

Plane body and blade support from a single

piece

In »bevel-down« planes an additional frog in

the plane body supports the blade. In »bevel-

up« planes, the plane body and blade support

are made from one piece, enhancing overall

stability.

METAL PLANE DESIGN TYPESThere are three types of metal planes:

»bevel-up« planes, »bevel-down« planes

and scraping planes.

* »BEVEL-UP«

The »bevel-up« plane evolved from the block

plane - a one-handed plane previously used

for planing cross-slots into posts to accommo-

date blockings for reinforcement. Hence the

name »block plane«. But back to the bevel-

up as the distinguishing feature. Basically,

the blade in the block plane is mounted the

opposite way round from that of a conventional

»bevel-down« plane. The reason for this

is the small size of the block plane, which

made it impossible and unergonomical to use

MANUAL WORK IS SOMETHINGENTIRELY INDIVIDUAL!

66

Planes

1

2

9

8

3

7

6

4

5

10

1 Plane blade2 Chipbreaker3 Cap iron4 Lateral adjustment lever5 Rear handle6 Depth adjustment screw7 Frog8 Adjustment screw for mouth opening9 Plane body10 Front handle

Planes

67

Simple mouth adjustment

»Bevel-up« planes have a screw at the front

end for adjusting the mouth opening easily.

The cutting depth remains unaffected.

Reduced weight

The absence of the additional frog makes

»bevel-up« planes lighter than »bevel-down«

ones.

No lateral adjustment

The »bevel-up« version works without a

lateral adjustment screw, which may be con-

sidered a disadvantage. As with the wooden

plane, the blade is adjusted by tapping

lightly on its sides.

* »BEVEL-DOWN«

The renowned plane inventor Leonard Bailey,

who worked for Stanley in his day, was a major

influence on modern plane design. Stanley

enhanced his system with its Bedrock

Design, which enables the frog position to be

modified without loosening the blade fixture.

With the exception of a few minor adjust-

ments, his design has remained unchanged

ever since. Only the blade-adjustment mech-

anism has been modified. It was revolu-

tionised by Thomas Norris, who introduced a

single screw for adjusting both the cutting

depth and the blade angle.

Experts continue to discuss the advantages

and disadvantages of this system, as, with

the Bailey-type adjuster, adjustments can be

made while planning through a low central

adjustment mechanism.

Advantages and disadvantagesCutting angle depends on frog angle

The cutting angle is more easily adjusted in

»bevel-up« than »bevel-down« planes.

However, frogs with different slope angles

are available for Lie Nielsen planes.

Simple lateral blade adjustment

Lateral adjustment of the blade is easily done

via the adjustment lever.

Full blade support

The frog provides a smooth and large seat

for the whole blade, reducing chatter to a

minimum.

Additional weight

Additional weight means the plane sits solidly

on the surface. This is particularly advan-

tageous for working with irregular grains and

wood that is difficult to plane.

Adjustment of mouth opening changes cutting

depth

Because the frog runs on an inclined surface,

any adjustment to the mouth also affects the

cutting depth. This can be counteracted by

turning the central adjusting mechanism.

* SCRAPING PLANES

Scraping planes arose from the idea of em-

bedding a scraper into a plane body for more

convenient use. Usually, a hook on the blade

is used for scraping. The blade has to be

ground perfectly angular to raise the hook,

which is applied to the upper edge of the

bevel with the burnisher, much like a scraper.

Tools with thick blades (by Lie Nielsen) do

not require a hook but are also used with one.

Those with thinner blades (made by Kunz

and Veritas) generally use the raised hook.

Their blades still have a bevel (30°-45°),

which reduces the amount of material need-

ing to be »displaced« when raising the hook.

The principle of scraping with a hook differs

greatly from cutting with a blade. Normally,

the depth is determined by the hook and

angle. These planes are indispensable for

achieving tear-out-free surfaces on difficult

woods and grains (primarily hardwood).

CUTTING ANGLES

When should the different cutting angles or

blade angles be used?

Cutting angle 36-38°

Preferred for end grain, where less tear-out

is to be expected because the fibres break

easily. With this cutting angle, the fibres

are actually cut off. When planing along the

grain, you should only take fine shavings with

a small mouth opening to prevent premature

splitting of the wood.


Normal cutting angle for general work with

relatively low cutting resistance.


On highly figured wood this angle creates

less tear-out, by breaking the fibres before

they split. A disadvantage is that the iron will

cut less and scrape more which dulls the iron

more quickly.

Blade angle 75-100° (cutting angle is defined

by a raised burr)

At this angle, you scrape instead of cutting

(scraping plane). Since this type of planing

causes minimal tear-out, it is ideal for wild

grain structures and woods that are difficult

to plane.

Planes || Lie-Nielsen planes

68

Lie-Nielsen® planes

Based in the US, Lie-Nielsen specialisesin re-introducing and improving traditionalplane types. Lie-Nielsen makes its toolsfrom only the finest materials, many ofwhich had previously been too expensive,not yet fully developed or unavailable insuitable tool-making quality. Today, Lie-Nielsen plane blades are made of A2steel, which prolongs the edge life andprevents rust. In all models, a bladethickness of 3 to 3.5 mm reduces vibra-tions when the tool is in use. During pro-duction, blades are hardened to approx.62 HRC and subjected to low-tempera-ture treatment (cryogenic hardening) foran even finer grain and enhanced dura-bility. Plane bodies are made of stress-relieved, wear-resistant spheroidal castiron, which is highly resistant to crackingand absorbs vibrations.

Because of the complex techniques re-quired, Lie-Nielsen is the only producer to manufacture models with manganesebronze alloy plane bodies and compo-nents. Manganese bronze alloy is break-resistant, rust-proof and adds mass tothe planes. The soles are perfectly planeand trued at right angles to the sides.Unless otherwise specified, the blade isangled at 45°. Cherry-wood handlesmake the tools comfortable to hold.

Casting bronze for plane bodies

»Bevel-up« planes- No chipbreaker required- Simple adjustment of cutting angle

by changing bevel angle

A NO. 100 PALM PLANE

Flat soleNo. 703775 67.82 € 80.70 € Repl. blade No. 703776 20.84 € 24.80 €

Round soleNo. 703777 85.71 € 102.00 € Repl. blade No. 703778 27.14 € 32.30 €

B NO. 103 AND NO. 102 BLOCK PLANESHandy precision planes with bodies andpolished cap irons made from bronze.The stainless steel adjuster allows accurateadjustment of the thick blades with mini-mum backlash.Blade width 32 mmBlade thickness 3.2 mmLength 135 mm425 g

A

B

C NO. 9 1/2 AND NO. 60 1/2 BLOCK PLANESA solid body, precise blade guide and adjuster, and an accurately positionedbronze chipbreaker with polished handgrips guarantee convenient operation andperfect results. The mouth opening canbe adjusted according to the application,using the configurable shoe (for removingthick or thin shavings).Blade width 35 mmBlade thickness 3.2 mmLength 160 mm750 g

1

2

D NO. 60 1/2 R RABBET BLOCK PLANE

No. 703770 150.42 € 179.00 €Repl. blade No. 703771 36.89 € 43.90 €

E NO. 140 SKEW BLOCK PLANE

No. 703708 203.36 € 242.00 €Repl. blade No. 703728 36.22 € 43.10 €

1

C

D

2

E

For B1 and B2Repl. blade No. 703722 27.65 € 32.90 €Toothed bl. No. 703739 50.34 € 59.90 €

For C1 and C2Repl. blade No. 703737 31.68 € 37.70 €Toothed blade No. 703740 50.34 € 59.90 €

1 No. 103, angle 20°For heavier cuts with the grain. Bevel angle 25°. Results in a normal cutting angle of 45°.No. 703702 105.04 € 125.00 €

2 No. 102, low angle 12°For fine cuts and end grain. Bevel angle25°. Results in a cutting angle of 37°.No. 703703 105.04 € 125.00 €

1 No. 91/2, angle 20°For heavier cuts with the grain. Bevel angle 25°. Results in a normal cutting angle of 45°.No. 703758 149.50 € 177.90 €

2 No. 60 1/2, low angle 12°For fine cuts and end grain. Bevel angle25°. Results in a cutting angle of 37°.No. 703714 149.50 € 177.90 €

This plane is ideal for cutting rabbets ortrimming tenons to fit. The low cuttingangle of 12° also makes it an excellentchoice for end grain. Fine blade-adjust-ment mechanism, non-adjustable mouth. Bevel angle 25°. Results in a cutting angle of 37°.Blade width 44 mmBlade thickness 3.2 mmLength 160 mm770 g

This replica of the Stanley 100 performs allprecise craft carpentry, model-making ormusical instrument-making work effortlesslyand cleanly. 3 mm thick, vibration-resistantblade, tongue-shaped handle and bronzecap. The curved sole design is suitable forconcave surfaces. Pitch of the iron 12°, bevel angle 25°. Results in a cutting angleof 37°.Blade width 22.5 mmBlade thickness 3.2 mmLength 90 mm210 g

A versatile plane with a tilted blade for askewed cut. With its adjustable fence andremovable right face, the reincarnation ofthe Stanley No. 140 is ideal for rabbetsand cornices, even at an angle to the grainand with end grain. Pitch of the iron 12°,bevel angle 25°. Results in a cutting angle of 37°.Blade width 40 mmBlade thickness 3.2 mmLength 170 mm1000 g

Including sharpening service.See page 2 for more information.

Free lifetime sharpening for Premium products

Two free sharpenings

Bronze cap iron

Brass lock screw

Adjustable throat plate Throat

Frog Spinwheel Stud

Blade adjuster nut

Brass lever


69

A CHISEL PLANES NO. 97 1/2

Blade width 45 mmBlade thickness 4.8 mmLength 160 mm630 gNo. 703707 125.21 € 149.00 €

B RABBET PLANE NO. 73

Blade width 19 mmBlade thickness 3.6 mmLength 195 mm1050 gNo. 703779 175.63 € 209.00 €Repl. blade No. 703780 31.60 € 37.60 €

Blade width 31 mmBlade thickness 3.6 mmLength 205 mm2000 gNo. 703756 226.05 € 269.00 €Repl. blade No. 703757 36.13 € 43.00 €

AB

Repl. blade No. 703727 36.22 € 43.10 €

Special plane for smoothing wood joints,rabbets, corners etc. Heavy blade onfinely-milled bed, knurled screw for adjustment. Pitch of the iron 15°. Bevelangle 25°. Results in a cutting angle of40°. Bronze body.

When it was first introduced by Preston inthe late 19th century, the No. 73 represent-ed a major breakthrough in plane design.Record continued making the No. 73 untila few years ago. Now, Lie-Nielsen has be-gun manufacturing its own version with thesame quality as its predecessor. The mouth,easily adjustable using a setscrew, and theprecisely machined, box-shaped body makethis plane the tool of choice for fitting andfinishing shoulders, rabbets, tenons andgrooves. Bronze cap iron. Pitch of the iron18°, bevel angle 25°. Results in a cuttingangle of 43°.

Lighter than the conventional benchplanes, these devices have a thickerblade and no chipbreaker, making themeasier to set up. The blade is held in thebed with the bevel facing upwards. Thismakes the cutting angle easy to adjust.The plane body and blade support arecast from a single piece for greater planestability and, thanks to the front handle,the mouth is easy and convenient to adjust. Brass caps.

1 No. 164 Low-angle smoothing plane

No. 703716 239.50 € 285.00 €Repl. bladeNo. 703741 36.22 € 43.10 €Toothed bladeNo. 703742 62.86 € 74.80 €

2 No. 62 Low-angle jack plane

No. 703706 221.01 € 263.00 €Repl. bladeNo. 703726 36.22 € 43.10 €Toothed bladeNo. 703749 58.40 € 69.50 €

C

1

This compact low-angle plane copes easi-ly with planing against the grain, endgrain and knotty wood. The central, Bai-ley-type blade adjuster allows smooth ad-justment of the cutting depth, even whileplaning. The blade is set at a 12º angle.Bevel angle 25°. Results in a cutting an-gle of 37°. Adjustable mouth.Blade width 50 mmBlade thickness 4.8 mmLength 245 mm1760 g

This plane is patterned after the StanleyNo. 62, which was specially designed forsmoothing butcherblocks. It easily copeswith even the most difficult jobs, such asplaning end grain and long-grained orknotty wood. The blade is set bevel-up inthe milled bed at a 12° angle. Bevel an-gle 25°. Results in a cutting angle of37°. The mouth opening can be adjustedvia the movable shoe.Blade width 50 mmBlade thickness 4.8 mmLength 355 mm2180 g

2

C LOW-ANGLE BENCH PLANES NO. 164, NO. 62

Mouth-plate locking screw

Mouth

Cap pivot pinMouth-plate adjuster screw

Retainer pin

SoleAdjustablemouth plate

BladeCast iron body

Threaded rod

Blade adjuster nut

Bronze capSpinwheel

Cap screw

Bronze cap iron Cap ironthumbscrew

Blade

Front knob

Adjustablemouth plate Mouth

Frog area

Stainless steel adjuster nut

SoleThreaded rod

Brass adjust-ment lever

A NO. 9 IRON MITRE PLANE

No. 703743 335.29 € 399.00 €Repl. blade No. 703744 40.67 € 48.40 €

B BIG ROUTER PLANE

No. 703781 117.56 € 139.90 €Repl. blade No. 703782 29.33 € 34.90 €

B

A

»Bevel-down« planes- Chipbreaker required- Cutting angle defined by frog angle

Bench planes No. 4, No. 4 ½, No. 5, No. 6, No. 7The all-purpose woodworking plane. With its Bedrock design, this plane allows chatter-free cutting thanks to its fully supported blade and a mouth thatcan be adjusted without removing thecap iron and blade. Additional lateralblade adjustment and the low blade-feedadjuster mean the cutting depth can bechanged during planing. Its heavy weightmakes irregular grain or difficult woodseasier to work. Brass frog and cap.

C NO. 4 SMOOTHING PLANEThe standard smoothing plane is capable of taking the finest shavingsfrom the most difficult woods.Blade width 50 mmBlade thickness 3.2 mmLength 225 mm

1 Spheroidal cast iron1950 gNo. 703712 271.34 € 322.90 €

2 Bronze2100 gNo. 703736 315.97 € 376.00 €

D NO. 4 ½ SMOOTHING PLANEThe ultimate smoothing plane, thanks to a large sole, extra-thick vibration-absorbent 3.6 mm blade and high weight.Blade width 60 mmBlade thickness 3.6 mmLength 260 mm2500 gNo. 703751 293.28 € 349.00 €Repl. bladeNo. 703752 45.21 € 53.80 €

C

1

2

D

70


For C1 and C2Repl. bladeNo. 703735 36.22 € 43.10 €Toothed bladeNo. 703738 58.40 € 69.50 €

The perfectly flat sole and perfectly square sides make this planewell suited for even the most demandingwork on end grain, side grain and mitredsurfaces. The lateral guide knob can beused on either side in conjunction with ashooting board. The mouth opening canbe adjusted via a sliding plate. The 4 mm thick blade can be preciselyadjusted to the nearest hundredth of amillimetre, even while planing. Pitch ofthe iron 20°, bevel angle 25°. Results in a normal cutting angle of 45°.Blade width 50 mmBlade thickness 4.8 mmLength 275 mm2350 g

Designed based on an early Stanley version, this router plane is very usefulfor planing precise mortises, grooves and other recessed areas. The improved depth stop and fine bladeadjustment allow for precise adjustmentsof the square-shaped and therefore direc-tionally stable guided iron. The blade canbe fixed centrally (normal position) orclose to the edge for working corners. An included fence is fixed through elongated holes to the cast iron body andcan be turned around for guiding alongcurved edges.200 x 90 mm Blade width 9.5 mm 800 g

Bronze lever capFrog assembly

Lateral blade-adjustment lever

Threaded rod

SoleAdjuster tab

Adjuster screw (frog)

Yoke

Adjuster nut

Cap screwChipbreaker

Mouth Frog hold- down pins

Locking screws

A NO. 5 JACK PLANEThe increased length and weight compared to the No. 4 planemakes it ideal, not only for smoothingbut also for levelling surfaces.Blade width 50 mmBlade thickness 3.2 mmLength 355 mm2550 gNo. 703715 293.28 € 349.00 €Repl. bladeNo. 703735 36.22 € 43.10 €Toothed bladeNo. 703738 58.40 € 69.50 €

B NO. 6 FORE PLANESize midway between a jack plane and a jointer plane. Ideal fortrueing, and joining of medium-sized boards. Flatness tolerance max. 0.1 mm.Blade width 60 mmBlade thickness 3.6 mmLength 450 mm3300 gNo. 703759 335.29 € 399.00 €Repl. blade No. 703752 45.21 € 53.80 €

C NO. 7 JOINTER PLANEMost popular jointer size, excellent for trueing and for making fitting and joint surfaces. Flatness tolerance max. 0.1 mm.Blade width 60 mmBlade thickness 3.5 mmLength 550 mm3700 gNo. 703753 377.31 € 449.00 €Repl. blade No. 703752 45.21 € 53.80 €

Scraping planes- Scrape surfaces without tear-out,

even on difficult woods- Cut using raised-edge burr

1 No. 212 Scraping planeFor working thin or small pieces made of hardwood such as fly rods, violin bows,frames etc. Bronze body.Blade width 35 mmBlade thickness 3.2 mmLength 135 mm680 gNo. 703710 157.98 € 188.00 €Repl. blade No. 703730 22.61 € 26.90 €Toothed blades1.4 mm No. 703731 40.67 € 48.40 €1.0 mm No. 703732 40.67 € 48.40 €

2 No. 112 Scraping planeWide-bladed scraping plane ideal for finishing large surfaces such as tabletops, parquet etc.Blade width 70 mmBlade thickness 3.6Length 235 mm1800 gNo. 703717 211.76 € 252.00 €Repl. blade No. 703718 36.13 € 43.00 €Toothed blades1.4 mm No. 703760 58.74 € 69.90 €1.0 mm No. 703761 58.74 € 69.90 €

E NO. 66 BEADING TOOLScraping plane with 8 profiled blades(16 different shapes) and two bladeblanks which can be shaped and hardenedindividually for cutting mouldings andgrooves.

Comes with 2 fences (straight, rounded).Bronze body.Blade width 16 mmBlade thickness 1.5 mmLength 280 mm500 gNo. 703713 157.98 € 188.00 €

Spokeshaves- Large handles for high level

of tool control - For working on straight, convex and

concave surfaces

F LIE-NIELSEN® MINI SPOKESHAVES

SoleFlat No. 703767 85.71 € 102.00 € Arched No. 703769 85.71 € 102.00 €

A

B

C

D

2

E

F

71


Repl. blade No. 703768 31.68 € 37.70 €

Based on models by the company Prestonwhich have not been produced for 80years, this replica guarantees optimumresults with its fine mouth openings andextra-thick blades. The winged handlesmade of polished bronze are comfortableto use. Cutting angle 38°.Blade width 50 mmBlade thickness 3.2 mmLength 175 mm135 g

D SCRAPING PLANES NO. 212 AND NO. 112Hardened blade (50-55 HRC) with 45°bevel to reduce material displacement.For preparing veneer surfaces, we recom-mend toothed blades. Adjustable bladeangle (75-100°).

1

See our webshop at www.more-than-tools.de for more Lie-Nielsen planes.

Veritas® planes

The corporate philosophy of Canadiantool manufacturer Veritas aims to developnew adjustment mechanisms and enhancehistoric plane design. With bodies madeof stress-relieved spheroidal cast iron,these tools are highly resistant to crackingand distortion. Their soles are perfectlyplane and trued at right angles to the sides. Their thick blades of high-strengthA2 steel are hardened to 60-62 HRC andadditionally subjected to a special low-temperature process to achieve a finergrain. Two setscrews on the sides con-strain the blade laterally, keeping it inplace regardless of the type of stress applied. Unless otherwise specified, theblade is angled at 45°. With their materialcombination of finely-ground or black-coated cast iron bodies, polished brasssetscrews and beautiful bubinga handles,these planes are also pleasing to the eye.



A APRON PLANE

No. 703695 91.60 € 109.00 €Repl. blade No. 703696 22.52 € 26.80 €

B BLOCK PLANECompact all-round planes for fine shavings. The mouth opening can be adjusted according to the application,using the configurable shoe (for removingthick or thin shavings). The indentationsin the sides make it easier to guide thishandy plane accurately. Central setscrewfor iron depth and lateral adjustment.Blade width 40.5 mmBlade thickness 3.2 mmLength 160 mm800 g

A B

1

C LOW-ANGLE SMOOTHING PLANE

2


D NO. 4 SMOOTHING PLANEThe standard smoothing plane is capableof taking the finest shavings from themost difficult woods. With the central adjusting screw, the blade feed and later-al position can be adjusted quickly andprecisely. The rear handle and frog forma movable unit that defines the mouth No. 703680 200.84 € 239.00 €

Repl. blade No. 703681 41.93 € 49.90 €

D

Repl. blade No. 703691 28.99 € 34.50 €No. 703690 194.96 € 232.00 €

72

Planes || Veritas planes

For B1 and B2Repl. blade No. 703694 33.53 € 39.90 €

1 Standard block plane 20°For heavier cuts with the grain. Bevel angle 25°. Results in a normal cutting angle of 45°.No. 703692 130.25 € 155.00 €

2 Low-angle block plane 12°For fine cuts and end grain. Bevel angle25°. Results in a cutting angle of 37°.No. 703693 130.25 € 155.00 €

For planing difficult grain, end grain,cross-grain or knotty wood.The front handle allows easy and convenient adjustment of the planemouth. Thanks to the central adjustingscrew, the blade feed and lateral positioncan be adjusted quickly and precisely.

Veritas’s smallest plane weighs only 420 gbut is impressively solid. Ideal for cabinet-makers, instrument makers and restorers.Central setscrew for iron depth and lateraladjustment. Non-adjustable mouth. Pitchof the iron 12°, bevel angle 25°. Resultsin a cutting angle of 37°.Blade width 31 mmBlade thickness 2.5 mmLength 140 mm420 g

C

Spokeshaves- Large handles for high level of

tool control - For working on straight, convex and

concave surfaces

E SPOKESHAVESFor fine shavings when working on flat andlong curved surfaces such as bows, boats,slats, planks and edges. Because they areguided by hand and are sensitive to thewood structure, spokeshaves must havehefty bodies and thick cutting blades(3.2 mm). The blade can be adjusted withknurled screws, the mouth opening withsupplied shims. The radius of the roundversion is 44 mm, while the concave version has an inside radius of 33 mm.Blade thickness 3.2 mmLength 270 mm330 g

1 Straight soleBlade width54 mm No. 703684 79.83 € 95.00 €Repl. blade No. 703686 22.27 € 26.50 €2 Round sole54 mm No. 703685 79.83 € 95.00 €Repl. blade No. 703686 22.27 € 26.50 €3 Concave sole40 mm No. 703687 88.24 € 105.00 €Repl. blade No. 703688 29.41 € 35.00 €

F LOW-ANGLE SPOKESHAVEA modern version ofa traditional woodenspokeshave (before1900) with new ma-terials and settings, this spokeshave isideal for working on curved and straightworkpieces with a difficult grain.The blade, set with the bevel facing up(20° basic bevel with a 25° micro-bevel),forms a cutting angle of 30° with the 5°slant of the curved sole. The thickness ofthe shavings can be adjusted via the toepiece, the mouth opening and by movingthe blade. By flipping the toe piece180°, you can change from a straightsole to a curved sole for concave work.Aluminium body, anodised.Blade width 50 mmBlade thickness 3.2 mmLength 265 mm200 gNo. 703623 57.98 € 69.00 €Repl. blade No. 703624 17.56 € 20.90 €

E

1-2

G PULLSHAVEHighly effective toolfor working all con-cave surfaces, e.g.stair construction,chair seats and largebowls, for makingmusical instru-ments, sculptures,etc. Optimum controlthanks to two-handed operation. The chipthickness can be precisely set by meansof two knurled screws. Radius approx. 87 mmBlade width 51 mmBlade thickness 3.2 mmLength 260 mm500 gNo. 703625 116.81 € 139.00 €Repl. blade No. 703626 25.13 € 29.90 €

3

F

G

opening without requiring any re-adjustment of the cutting depth.Blade width 50 mmBlade thickness 3.2 mmLength 240 mm2000 g

Blade angle 12°. A 25° bevel angle produces a cutting angle of 37°.Blade width 50 mmBlade thickness 3.2 mmLength 265 mm1700 g

See our webshop at www.more-than-tools.de for more Veritas® planes.

73

Planes || DICK planes

-Planes

Centuries ago, we at DICK developed a plane series for violin makers. Sincethen, Herdim® planes have establishedthemselves on the market. We have nowcreated a new series of metal planeswhich fulfils our expectations of goodtools while at the same time still beingaffordable. The solid plane bodies madefrom cast steel with precisely groundsoles aligned at right angles to the sides,together with the 3 mm thick bladesmade from SK4-steel (62 HRC) signifytop quality. The blade adjuster allows for precise adjustmentsand the ergonomicallyshaped handlesdevelopedthrough tests as well as thepolished capirons sit well in the hand.Handles of native beechwood.

Available mid-July 2010.



A BLOCK PLANECompact, solid block planes which,thanks to polished cap irons, sit well in the hand. The mouth opening can be adjusted according to the application, using the configurable shoe. Blade-depthadjusting and cap iron fixation with easy-to-adjust brass screw and knob.Blade width 35 mmBlade thickness 3 mmLength 160 mm840 g

1 Normal blade angle 20°For working with the grain. Bevel angle 25°. Results in a normal cutting angle of 45°.No. 703330 41.93 € 49.90 €Repl. blade No. 703410 8.32 € 9.90 €

2 Low angle 12°For fine cuts and end grain. Bevel angle 25°. Results in a cutting angle of 37°.No. 703334 41.93 € 49.90 €Repl. blade No. 703414 8.32 € 9.90 €

3 Rabbet block planeThis plane is ideal for cutting rabbets ortrimming tenons to fit. It is an excellentchoice for end grain thanks to the low cutting angle of 12°. A 25° bevel resultsin a cutting angle of 37°. Fine blade-adjustment mechanism, non-adjustablemouth.Blade width 44.5 mmBlade thickness 3 mmLength 160 mm800 gNo. 703335 41.93 € 49.90 €Repl. blade No. 703415 8.32 € 9.90 €


B BENCH PLANES NO. 4, NO. 5, NO. 6With their Bedrock design, these planesallow chatter-free cutting thanks to thefully supported blade and a mouth thatcan be adjusted without removing thecap iron and blade. The rear handle, with its width of 26.5 mm, offers a comfortable grip even for large hands.Lateral blade adjustment through easy-to-reach lever. Cutting angle 45°.

1 No. 4 Smoothing planeThe standard smoothing plane is capableof taking the finest shavings from themost difficult woods.Blade width 51 mmBlade thickness 3 mmLength 250 mm2250 gNo. 703331 63.03 € 75.00 €Repl. blade No. 703411 13.87 € 16.50 €

Repl. blade No. 703411 13.87 € 16.50 €

2 No. 5 Jack planeThe increased length and weight com-pared to the No. 4 plane makes this oneideal, not only for smoothing but also for levelling surfaces.Blade width 51 mmBlade thickness 3 mmLength 355 mm2770 gNo. 703332 79.83 € 95.00 €

3 No. 6 Fore planeMid-size plane ideal for trueing and joining of medium-sized boards. Blade width 60 mmBlade thickness 3 mmLength 450 mm3730 gNo. 703333 88.24 € 105.00 €Repl. blade No. 703413 13.87 € 16.50 €

A

1 2 3

B

1

Plane guideDifficult wood grains are often easierto work using the plane at a slight an-gle. However, the plane should beused parallel to the workpiece for thebest surface quality. Difficult grainsand softwoods can be smoothed bet-ter and with less effort if the surfaceis moistened.

Pressure distribution When starting the plane, first applypressure to the front of the sole.During the plane motion, the pressureshould be evenly distributed. At theend of the board, the pressure shouldbe on the rear of the sole. As theshavings become finer, the pressureon the plane must be increased tohold the blade in constant contact.When resetting, lift the plane fromthe workpiece to protect the cuttingedge.

2

3

Planes || Kunz planes

74

Kunz® planes

Kunz is known for its solid planes ofwear-resistant grey cast iron with fine-ground soles and good value for money.The standard tool-steel blades arehardened to approx. 62 HRC. For planingextremely hard woods, durable HSSblades (approx. 65 HRC) are availableas accessories. Their epoxy-coated greensurfaces make the Kunz planes, made inGermany, unique.



C NO. 101 POCKET PLANE

No. 703154 13.87 € 16.50 €Repl. blade No. 703130 3.53 € 4.20 €HSS blade No. 703155 12.35 € 14.70 €

D NO. 100 POCKET PLANE


A NO. 102 BLOCK PLANEHandy plane for craft carpentry makingmusical instruments. Pitch of the iron 25°,bevel angle 25°. Results in a cutting angle of 50°, which is suited best forhardwoods.Blade width 33 mmBlade thickness 2.5 mmLength 130 mm310 gNo. 703140 16.72 € 19.90 €Repl. blade No. 703141 5.80 € 6.90 €HSS blade No. 703142 16.72 € 19.90 €Toothed blade No. 703156 8.24 € 9.80 €

B NO. 9 1/2 BLOCK PLANERobust plane with lateral blade adjustment. The mouth can be adjusted via a throat plate. Low blade angle (12°). Bevel angle 25°.Results in a cutting angle of 37°.Blade width 41 mmBlade thickness 2 mmLength 180 mm600 gNo. 703243 63.78 € 75.90 €Repl. blade No. 703244 8.32 € 9.90 €

E NO. 75 BULLNOSE PLANE



F SMOOTHING PLANE NO. 4 PLUS

No. 703241 184.03 € 219.00 €Repl. blade No. 703242 27.73 € 33.00 €

G NO. 113 CIRCULAR PLANEReplica of a Stanleymodel from 1879.The curvature of theflexible steel sole isadjustable, allowingthe plane to be usedfor both concaveand convex surfaces. The double blade’slateral position can be adjusted via a tilt


Spokeshaves- Large handles for high level

of tool control - For working on straight, convex

and concave surfaces

H NO. 80 CABINET SCRAPERFor smoothing heavily structured woodsand removing glue and paper remnantsfrom veneered surfaces. Includes 1.1 mm thick scraper blade.Blade angle 110°.Blade width 70 mmLength 275 mm640 gNo. 703121 28.49 € 33.90 €Repl. blade No. 703131 4.79 € 5.70 €Toothed bl. No. 703153 13.87 € 16.50 €

J SPOKESHAVES WITH FINE BLADEADJUSTMENT NO. 51 A, NO. 51 ARFor fine shavings when working on flatand long curved surfaces. The bladedepth can be precisely adjusted. Radiusof round version (No. 51 AR) 35 mm.Blade width 52 mmBlade thickness 2 mmLength 250 mm320 g

Sole1 Straight No. 703127 15.04 € 17.90 € 2 Round No. 703129 15.04 € 17.90 €

I SPOKESHAVE WITHOUT FINE BLADEADJUSTMENT NO. 50, NO. 55For concave and convex surfaces, suchas chair seats, hand rails or round bars.The concave version No. 55 (350 g) hasan inside radius of 48 mm, the convexversion No. 50 (250 g) an outside radiusof 48 mm.Blade width 52 mmBlade thickness 2 mmLength 250 mm

Sole1 Convex No. 703124 20.08 € 23.90 € Repl. blade No. 703134 5.55 € 6.60 €2 Concave No. 703125 20.92 € 24.90 € Repl. blade No. 703135 6.39 € 7.60 €

Scraping plane- Scrapes surfaces without tear-out,

even on difficult woods- Cuts using raised-edge burr

C D

A

E

B

F

G

For J1 and J2Repl. blade No. 703137 4.96 € 5.90 €HSS blade No. 703139 19.75 € 23.50 €

Compact block plane, simple design.Cutting angle 38°.No chipbreaker.Blade width 25 mmBlade thickness 2 mmLength 85 mm120 g

Same specifications as No. 703154 but with tongue-shaped handle.No chipbreaker.Blade width 25 mmBlade thickness 2 mmSole length 85 mm160 g

For finishing rabbets, shoulders andgrooves. Cutting angle 38°.No chip breaker.Blade width 26 mmBlade thickness 2 mmLength 100 mm250 g

This smoothing plane, from the newKunz series »Kunz plus«, impresses withits precise technology and use of top-quality materials such as domestic cherrywood. The blade is adjusted (lateral anddepth) by only one screw, a techniquethat was first developed with the legendary Norris planes. The new Kunzversion uses the cap-iron screw as a connection for all adjustments. This planeis very handy due to the low knob at the

front and the low design. The short, 3.5 mm thick iron gives additional spaceat the rear handle. The precisely groundbody of the plane is made from resistant,annealed cast iron. Cutting angle 45°Blade width 50 mmBlade thickness 3.5 mmLength 260 mm1800 g

lever, while a knurled screw adjusts theshaving thickness. Cutting angle 55°.Blade width 44 mmBlade thickness 2 mmLength 260 mm1600 g

I

J

1

2

1

2

H

See our webshop atwww.more-than-tools.defor more Kunz planes.

Planes || Stanley planes, Anant planes

75

Stanley® planes



A STANLEY® BLOCK PLANEGrey cast iron block plane with ground soleand adjustable mouth opening. Cap ironclamped with eccentric lever. Lateral anddepth adjustment. Japanese plane blades(No. 718070) available as an option.

2 No. 60 1/2, low angle 13.5°Primarily for end-grain work. Bevel angle25°. Results in a cutting angle of 38.5°.Blade width 35 mmBlade thickness 2 mmLength 160 mm660 gNo. 703011 50.34 € 59.90 €Repl. blade No. 703012 8.32 € 9.90 €

1 No. 9 1/2, angle 21°For cuts with the grain. Bevel angle 25°.Results in a normal cutting angle of 46°.Blade width 41.5 mmBlade thickness 2 mmLength 160 mm770 gNo. 703001 52.86 € 62.90 €Repl. blade No. 703002 8.32 € 9.90 €Toothed bl. No. 703014 17.56 € 20.90 €

Anant® planes



B NO. 77 ALL-PURPOSE RABBET PLANERemovable head allows conversion to achisel plane. Mouth opening adjustablewith shims, blade adjustment via a knur-led screw. Pitch of the iron 20°. Bevel angle 25°. Results in a normal cutting angle of 45°.Blade width 29 mmLength 102 mm460 gNo. 703177 41.60 € 49.50 €Repl. blade No. 703178 6.64 € 7.90 €


C A10 BENCH RABBET PLANEAs the blade ends flush with the side faces, this plane is suitable not only forworking surfaces, but also for cornices,corners and rabbets. Fine blade adjustment and lateral lever.Blade width 53 mmBlade thickness 2 mmLength 325 mm1850 gNo. 703206 46.13 € 54.90 €Repl. blade No. 703207 6.64 € 7.90 €

D BENCH PLANES NO. AA 4, NO. AA 5

1 No. AA 4 Smoothing planeThe standard smoothing plane is capableof taking the finest shavings from themost difficult woods.Blade width 50 mmBlade thickness 3.3 mmLength 250 mm1900 gNo. 703215 33.53 € 39.90 €

2 No. AA 5 Jack plane The increased length and weight com-pared to the No. 4 plane makes this plane ideal, not only for smoothing butalso for levelling surfaces.Blade width 50 mmBlade thickness 3.3 mmLength 355 mm2240 gNo. 703216 42.77 € 50.90 €

For cutting grooves,tongues and rabb-ets. Parallel anddepth fence, spur,nickel-plated body.Supplied with 9 bla-des (3 - 16 mm) and carvers.Blade width -16 mmBlade thickness 2.3 mmLength 200 mm1500 g

E NO. 52 GROOVING PLANE

No. 703181 108.40 € 129.00 €9 repl. bladesNo. 703182 40.25 € 47.90 €

Tuning metal planes:

Flatten the front part of the back of theplane blade to ensure that there are nogaps in the contact with the chipbreakeredge. DMT diamond sharpening stones are perfect for this.Fit the chipbreaker flush with the bladeto prevent blockages from thin shavings.The distance between the chipbreakeredge and blade edge should be approx.2 mm for coarse work, 1 mm for medi-um, and 0.5 mm for fine shavings. The leading edge of the chipbreakershould be at a 45°-60° angle to the surface of the blade. The blade should

rest perfectly flush in the bed of theplane, which can be finely tuned usinga file. Check the flatness of the plane'ssole using a precision metal ruler. Flatten the sole if necessary. We offer an alignment service for metal planes (see the Service section in thewww.more-than-tools.de webshop).To remove fine shavings with a narrowmouth opening, it is important that theleading edge of the mouth is straightand smooth to prevent the plane fromclogging. If necessary, shape the edgeof the metal-plane mouth using a file. A slight, 15° chamfer may be added tofacilitate the removal of the shavings.

A

21

B

C

D

1

2

E

Trueing plane soles

Uneven soles of metal planes can betrued relatively quickly using wet emerycloths, which are fitted to a level surface(e.g. a milling table or a thick glass pla-te). Depending on the warping, use agrain of 120 initially, then gradually fi-ner grains to approx. 600. Move the pla-ne (with the blade pre-tensioned but re-tracted) elliptically with constantpressure on the moist emery cloth, che-cking the results repeatedly, until the so-le is level. Use a straight edge to checkthat it is level No. 707291.

Universal plane with adjustable mouthopening for major stock removal andsmoothing. Fine blade adjustment withknurled screw, lateral adjustment withside lever. The tool's heavy weight makesit easier to plane irregular grains or difficult woods.

Anant, based in Jalandhare in India, hasbeen manufacturing metal planes basedon English models since 1949. A majorargument in favour of Anant planes istheir good value for money. Grey cast iron bodies and carbon-steel blades(58 HRC). Before use, the blades mustbe sharpened and the chipbreakersadjusted. The AA series has thicker solesfor better momentum, finely lapped solesand sides, as well as thicker plane bladesand chipbreakers. Handles of fine-grained sheesham wood.

Japanese plane blades suitable forAnant planes: page 76.

Repl. blade No. 703222 6.64 € 7.90 €

Repl. blade No. 703222 6.64 € 7.90 €

Planes || Accessories for metal planes, Japanese planes

76

Japanese planes (Kanna)

Before forge welding, the packet of thesoft iron body and the hard steel strip is heated to approx. 1050° in the smith'sfurnace.

D SMOOTHING BLOCK PLANE, 42 MM

No. 717013 57.14 € 68.00 €

E SMOOTHING PLANE, 64 MMHand-made plane offering good value formoney. Cutting edge of White PaperSteel. Block of Japanese white oak.Blade width 64 mmBlade thickness 6.5 mmLength 275 mm1064 gNo. 717006 65.55 € 78.00 €

F SMOOTHING PLANE, 65 MMMade in a Japanese master workshop.The blade is made from White PaperSteel and very rare iron (manufacturedbefore 1900) which, thanks to its silicaparticles evens and cleans the pores ofthe waterstone. Distinguishable fromother irons by the black spots.Japanese wihte oak block.Blade width 65 mmBlade thickness 6 mmLength 290 mm1255 gNo. 717001 158.82 € 189.00 €

Old anchor chain links are excellent material for plane-blade bodies.

G INOMOTO SMOOTHINGPLANE, 70 MMMade by Master Inomoto using the finestwhite oak and best steel. The blade ismade from Blue Paper Steel and veryrare iron (manufactured before 1900)which, thanks to its silica particles evensand cleans the pores of the waterstone.Distinguishable from other irons by theblack spots.Comes with a test shaving.Blade width 70 mmBlade thickness 7 mmLength 290 mm1355 gNo. 717023 255.46 € 304.00 €

H HARDWOOD PLANEExclusively from DICK:Ideal for working hardwoods. The steepangle of the blade (45° instead of 40°)reduces the danger of tear-outs whenworking against the grain. The cuttingsteel made of the highest-quality powderHSS (66 Rockwell, very tough) givesthe double-layered blade an outstandingedge life even with other wear-intensivematerials, like exotic woods, laminates or glued woods.Japanese white oak block.Blade width 55 mmBlade thickness 6 mmLength 240 mm750 gNo. 718088 150.42 € 179.00 €

D

E

F G H

Accessories for metal planes B JAPANESE PLANE BLADES FORRECORD, STANLEY, AND ANANT PLANESMade of double-layered, laminated steelto ensure superior durability, easier sharpening and better vibration control.The exceptionally fine-grained WhitePaper Steel will hold a razor-sharp edge.Blade thickness 2-3 mm.

1 Stanley 9 1/2Groove width 15.1 mm.41.5 x 110 mmNo. 718073 39.92 € 47.50 €

3 Record 9 1/2, 60 1/2 and Anant 9 1/2Groove width 11.8 mm.41.5 x 110 mmNo. 718074 36.89 € 43.90 €

2 Stanley, Anant 60 1/235 x 110 mmNo. 718075 39.41 € 46.90 €

4 Record, Anant 4 and 550 x 190 mmNo. 718070 41.93 € 49.90 €

5 Stanley, Record, Anant 4 1/2, 6 and 760 x 200 mmNo. 718072 46.97 € 55.90 €

C ROSEWOOD PLANE HANDLESUntreated plantation-grown rosewoodhandles for retrofitting to your Kunz,Stanley, Record or similar metal planes.They fit all No. 3 - No. 8 planes, but so-metimes may require slight modificationto obtain a perfect fit. Set (handle, knoband screws).No. 702900 23.03 € 27.40 €

3

1

2

4

5

CB

A LEATHER BLOCK PLANE CASE

No. 702999 31.85 € 37.90 €

A

Fits block planes:Lie-Nielsen 703758 / 714 / 770,Veritas 703695 / 692 / 693,Stanley 703011 / 001,DICK 703335 / 330 / 334.Well-finished case made of heavy-dutyleather. The flap serves both as a beltloop and a closure.40 x 55 x 185 mm

Hand-made plane with cutting edge ofBlue Paper Steel that can be conveniently used with one hand. Japanese white oak body.Blade width 42 mmBlade thickness 5 mmLength 150 mm335 g

Japanese planes bring the wood's true inherent beauty to the fore. Kanna havebeen reduced to their most essential planefunctions. The double-layered, taperedblade is much thicker than standard European blades, allowing chatter-freeplaning. The cap, also made of double-layered steel, serves as a chipbreaker.The numerous adjustment mechanismsfound on European planes are completelyabsent. Before using a Kanna for the firsttime, the blade’s back must be flattenedand the blade properly seated in the tapered grooves of the body. To minimisefriction, the sole can be given a slightlyconcave profile using a scraping plane.Anyone willing to make the initial effortof setting up and learning how to usethese fascinating tools will be rewardedwith exceptional results. Unless otherwise noted, the pitch of the iron is 40°. Instructions included.

Taperedblade

Blade bed

Hollowgrind (Ura)

Chamferedcorners

Side groove

Retaining pin

Plane block, made ofwhite or red oak

Chipbreaker

Planes || Japanese planes

77

In Japan, theworkpiece is notfixed betweenbench dogs, butis simply laid on aplaning board or aplaning beam with a stopper.

The right hand is used tohold the front of the pla-ne, push it down andpull. The left hand re-mains behind the blade

and guides it.Softwoods are easier to plane if they are moistened slightly. A dust-free work-shop is recommended for high surfacequality when planing. Grinding dust inparticular blunts plane blades. Cleanthe wood surface thoroughly before planing.

After working, push the Kanna bladeback somewhat to reduce the tensionon the block.

Ready-to-use Japanese planes with replaceable HSS bladesThe Kanna's remarkable smoothness isprimarily attributable to its particularlythick plane blade, which generally mustbe sharpened by hand and set into thebody before use. The Kanetomo planesallow you to forego these time-consumingsteps by using replaceable HSS cutters.The cutters fit flush into a recess in theback of the heavy, vibration-absorbingblade.

The razor-sharp cutters will produce first-class surface finishes even when workingdifficult materials. They are hardened to68 Rockwell to guarantee superb edge life.

3 Blade width 58 mmBlade width 58 mmLength 255 mm940 gNo. 717057 57.90 € 68.90 €

B CHAMFER PLANE, SKEWEDFor 45° bevels. The bevel width can beadjusted (0-16 mm). The chipbreakerand the slightly angled blade (pull-cut-ting) allow it to be used even with diffi-cult grain. Japanese white oak body.Blade width 30 mmBlade thickness 5.5 mmLength 200 mm435 gNo. 717031 94.12 € 112.00 €

C MINI CHAMFER PLANEParticularly fine design. The bevel widthcan be adjusted (0 – 8 mm).Japanese red oak body.Blade width 18 mmBlade thickness 4.5 mmLength 110 mm105 gNo. 717029 102.52 € 122.00 €

F CHAMFER PLANEWith removable fence for45°, 60° and 30° bevels.Solid carbon-steel blade,approx. 62 Rockwell.Screw chipbreaker,Japanese white oak body.Blade width 20 mmBlade thickness 3.5 mmLength 150 mm290 gNo. 717033 29.33 € 34.90 €

G RADIUS PLANEWith two radii, 2.5 and5 mm. Carbon-steel planeblade (62 Rockwell), withscrew cap. Japanese white oak body.Blade thickness 3 mmLength 150 mm190 gNo. 717034 25.97 € 30.90 €

E COMPASS PLANEThe sole is curved along its length andwidth, making it perfect for shaping seatbottoms, bowls, stringed-instrumentbodies etc.Japanese white oak body.Blade width 36 mmBlade thickness 7 mmLength 155 mm342 gNo. 717020 100.00 € 119.00 €

D SCRAPING PLANEVertical blade. For trueing the soles ofJapanese planes, working very hardwoods and thin pieces. Plane across ordiagonal to the grain.Japanese white oak body.Blade width 42 mmBlade thickness 6 mmLength 155 m396 gNo. 717015 52.86 € 62.90 €

More Japanese planes are availablein our music catalogue or online atwww.more-than-tools.de

A SMOOTHING PLANE (KANETOMO)Resin-impregnated Japanese red oakbody, highly resistant to wear and warp-ing. The chipbreaker is not adjustable.



A

1 2 3

B C D E

GF

Kanna - king of the woodworking tools

Guest article by Toshio Odate

Planes existed already in Ancient China.From there, they spread to neighbouringcountries, including Korea. Theseplanes were pushed. They had handleson each side. The plane blade was in-serted into a wooden block and held inplace by a wedge, very much like a We-stern plane.

This Chinese-originated push plane arr-ived in Kyu Shyn, a southern island ofJapan, through Korea in the late fifteenthto early sixteenth century.

The plane was commonly used in astanding posture. However, the Japanesecraftsman works mainly in a sitting orsquatting position, in which it is almostimpossible to push a plane, especiallywith handles.

To accommodate the Japanese crafts-man´s working posture, and for severalother reasons, the original design of thepush plane with handles evolved ratherquickly as it arrived in Japan. Perhapsthe handles were first removed, then theplane became a pull-stroke instead of apush plane. The pull-stroke plane quickly became avery important tool in Japanese wood-working. More than sixty designs andtypes of planes emerged from the pushplane. The Japanese craftsman especiallycalls the common plane Hira-Kanna todistinguish it from the many others.

In Japanese woodworking the plane isinvolved from the beginning of a projectto its end; very seldom does the Japan-ese craftsman use sandpaper and woodfinish.

The soles of all these planes are tuneddifferently. The quality of woodworkingdepends directly on how well the crafts-man adjusts and uses the plane.

Japanese craftsmen call planes the»king of the woodworking tools«.

CD B

A

A = Plane bladeB = Repl. HSS cutterC = ChipbreakerD = Pin for positioning

the chipbreaker

Planes || Traditional Chinese planes

78

Traditional Chinese planes

The basic design of the Chinese plane(Mu Bao) is similar to the Japanese Kanna. The major difference is that theChinese plane can be used on either thepull or the push stroke, whereas the Japanese Kanna can only be used on thepull stroke. The larger Chinese planes have a cross-handle to facilitate push-stroke use (which can be removed for useon the pull stroke). The blades are heldin place using a wedge or cap. Theslightly wave-shaped plane bodies aremade of either Hei Tan (a fine-grained type of ebony from Indonesia) or Shun-Gee (a type of rosewood). The uncoatedsurfaces are worked using scrapers andare polished. The plane blades are madeof wear-resistant HSS steel (approx. 64HRC), or forged carbon-steel (approx. 58HRC) for special-purpose planes, whichmake Chinese planes visually appealingand solid all-round tools. Unless other-wise specified, the blade angle and thusthe cutting angle is 40°.

A BLOCK PLANECompact ebony body with square sides.HSS blade with chipbreaker.Blade width 44 mmBlade thickness 3 mmLength 105 mm280 gNo. 702956 24.79 € 29.50 €Repl. blade No. 702957 8.32 € 9.90 €

B SMALL SMOOTHING PLANEEbony body with roof-like top.HSS plane blade with chipbreaker.Blade width 40 mmBlade thickness 3.5 mmLength 175 mm420 gNo. 702954 38.57 € 45.90 €Repl. blade No. 702955 7.98 € 9.50 €

C BLOCK PLANEIdeal for working hardwoods and difficultgrain. HSS plane blade with woodenwedge, no chipbreaker. Blade angle 60°.Blade width 30 mmBlade thickness 3 mmLength 125 mm170 gNo. 702962 19.24 € 22.90 €

D RABBET PLANEWave-shaped ebony body. HSS plane blade with wooden wedge, no chipbreaker.Blade width 25 mmBlade thickness 3 mmLength 150 mm190 gNo. 702964 23.36 € 27.80 €Repl. blade No. 702965 7.48 € 8.90 €

E RADIUS PLANEFor rounding edges, dowels and hand rails.Rosewood body, carbon-steel blade withwedge, no chipbreaker. Radius 18 mm(concave).Blade width 26 mmBlade thickness 2 mmLength 160 mm240 gNo. 702958 17.56 € 20.90 €Repl. blade No. 702959 5.21 € 6.20 €

Well-suited for work with all hardwoodsin the making of musical instruments aswell as artistic carpentry and chair- andmodel-making. With bodies of vibrant,grained, Makassar ebony and polished No. 710845 87.39 € 104.00 €

F MINI PLANESRosewood plane body with polished brasshardware. High-quality HSS blades.

1 Block planeCurved body, with horn.Blade width 13 mmBlade thickness 2 mmLength 80 mm65 gNo. 702946 18.40 € 21.90 €Repl. blade No. 702976 4.79 € 5.70 €

2 Rabbet / chisel planeFor working rabbets into the corners.Blade width 13 mmBlade thickness 2 mmLength 80 mm37 gNo. 702947 18.40 € 21.90 €Repl. blade No. 702949 4.79 € 5.70 €

3 Scraping plane

No. 702948 18.40 € 21.90 €Repl. blade No. 702976 4.79 € 5.70 €

J SPOKESHAVES, WING-SHAPEDCarbon-steelblades, withcranked tangsthat projectthrough the tool’sbody. Flat sole,Shun-Gee body.

Blade width 42 mmLength 150 mm25 gNo. 702970 10.00 € 11.90 €

Blade width 67 mmLength 190 mm50 gNo. 702971 11.26 € 13.40 €

H SPOKESHAVE, STRAIGHT SHAPEHSS blades, secured with wedge. Ebony body. Plain steel-plated sole.Blade width 30 mmBlade thickness 2.3 mmLength 265 mm107 gNo. 702975 20.76 € 24.70 €

Spokeshaves do not have chipbreakers.In order to prevent tear-out duringuse, it is therefore particularly importantthat the blade is extremely sharp andthat you work with the grain wherepossible.

I MULTI-BLADED SCRAPING PLANE(FLOAT)Chinese carpenters traditionally use thisscraping plane for bow-making or precise-ly shaping both flat and curved hardwoodsurfaces. The tool’s action is similar tothat of a scraper blade, yet with the ad-vantage that there is no wave effect whenworking even the most highly figuredwoods. Very efficient for rapidly removingstock when correcting the flatness orcurvature of a surface. Cambered Shun-Gee body with polished surfaces, comeswith 8 blades.Blade width approx. 45 mmLength 230 mm

Blade1 Straight No. 702978 23.61 € 28.10 € 2 Concave No. 702979 23.61 € 28.10 €

A

G EBONY MINIATURE PLANES - SET

Planing tips

Planes and spokeshaves work betterwhen the cutting edge of the blade is skewed to the direction of the cut(drawing cut). Technically, this is be-cause the effective cutting angle of theblade is reduced, as is the amount offorce required to make a cut.

Planes and spokeshaves should be drawnacross the workpiece quickly while applying even pressure. Slow strokesmay lead to unsteady cutting (chattering).

B C

D E

F

1 2 3

G

H

J

I

1 2

Cutting angle adjustable 80° to 90°.Blade width 13 mmBlade thickness 2 mmLength 80 mm60 g

brass caps, HSS blades(64 Rockwell). Set, 5 pieces.Blade width 18 mmBlade thickness 2.2 mmLength 90 mm

Price advantage

Repl. blade No. 702963 6.64 € 7.90 €

Planes || Western style planes

79

Western style planes

E.C.E.® planesTried-and-tested cabinetmaker's planefrom traditional German manufacturerEmmerich. Unless otherwise specified,the soles are made of extremely wear-resistant lignum vitae wood, whose self-lubricating effect ensures a smooth sliding action. The blades are sharpenedand set ready for use. The blade angleand thus the cutting angle is 50°.

A E.C.E.® BLOCK PLANELightweight plane for assembly work and making musical instruments. Large, hemispherical-shaped adjusting screw for setting the shaving thickness. White beech body.Blade width 39 mmBlade thickness 2.5 mmLength 150 mm450 gNo. 703101 55.97 € 66.60 €Repl. blade No. 703104 12.18 € 14.50 €

B E.C.E.® REFORM SMOOTHING PLANEClassic smoothing plane. Shaving thick-ness adjustable with a setscrew free ofbacklash. Blade pre-tensioning, adjustablemouth opening via a sliding plate, and lateral blade adjustment via a rocker. Thebody and asymmetrical handle (for right-handers) are made of air-dried cherry wood.Blade width 48 mmBlade thickness 3 mmLength 225 mm1200 gNo. 703105 150.00 € 178.50 €Repl. blade No. 703106 20.34 € 24.20 €

C E.C.E.® SMOOTHING PLANETraditional German smoothing plane withintegrated wedge support. The wedge caneasily be removed by hand. Domestic redbeech body, hornbeam sole with toothedjoint.Blade width 48 mmBlade thickness 2.8 mmLength 220 mm1000 gNo. 703109 58.57 € 69.70 €Repl. blade No. 703100 16.47 € 19.60 €

D E.C.E® PRIMUS RABBET PLANEIdeal for making and finishing rabbetsand adjusting tenons and hand rails.Backlash-free blade adjustment withknurled screw. The mouth opening is adjustable via the sliding plate held in a grout and a wing nut. Durable whitebeech body.Blade width 30 mmBlade thickness 3 mmLength 270 mm840 gNo. 703092 127.98 € 152.30 €Repl. blade No. 703093 20.59 € 24.50 €

E E.C.E.® RABBET PLANEMouth opening adjustable via slidingplate and wing nut. Hornbeam bodyand sole.Blade width 30 mmBlade thickness 2.8 mmLength 270 mm560 gNo. 703108 59.50 € 70.80 €Repl. blade No. 703110 15.04 € 17.90 €

F E.C.E.® ROUTER PLANEFor making grooves, grouts and other recessed surfaces. Red beech body. 3 L-shaped blades, bevel angle 25°.Widths 10, 15, 20 mmLength 220 mmApprox. 770 gNo. 703098 77.73 € 92.50 €3 repl. bladesNo. 703099 54.62 € 65.00 €

G ULMIA® DOVETAIL PLANEThis Western style model has a solid pla-ne body made of red beech with a whitebeech sole, which is hard and wear-resis-tant. The sole is inclined at an angle of73 degrees to the right-hand surface.The metal fence allows for adjustingthe required depth. The inclination andthe pitch of the iron allow a skewed cutand also easier sharpening because theiron is formed like a normal plane iron.The blade also guides the cutting forcestowards the inside to prevent surfacetearing along the dovetail tip. This technical solution is not consideredby many other suppliers and thereforefairly rare. A scoring spur which can befitted as required minimises the risk ofsurface tearing.Blade width 33 mmBlade thickness 3 mmLength 240 mm965 gNo. 703800 98.24 € 116.90 €

K DOVETAIL CUTTERWith this dovetail cutter for use with arouter, you can not only make joints morequickly and precisely, but also a lot moreeasily. The router cuts the grout into thewood and the matching sliding dovetail isadded to the counterpart using our UlmiaDovetail Plane. Cutter 17° and plane 73°match perfectly. The cutter is made ofcarbide metal and thus provides a longservice life even when used for hardwood.Shaft diameter 8 mmOverall length 60 mmDiameter 20 mmTilt angle 17 °Max. depth of cut 16 mmNo. 707361 33.53 € 39.90 €

H EDGE-TRIMMING PLANESFor rounding or chamfering solid-woodedges, also for laminates, multilayerboard, corian etc. The double blades(pre-cut and post-cut) allow clean cutsto be made even when working difficultgrain. Maple body with brass fitting onthe sole. Blades of extremely wear-resistant HSS steel.Length 175 mm155 g

Rounding planeRadius 3 mm.Length 175 mm155 gNo. 703095 16.39 € 19.50 €

Chamfer plane45° chamfer, 3 mm.Length 175 mm155 gNo. 703094 16.39 € 19.50 €

I BOWMAKER´S SCRAPING PLANESpecial tool for precision-finishing (tille-ring) traditional bows, also ideal for ma-king instruments, ribs, model making orthinning leather straps. The spokeshavewith a vertical blade facilitates high-pre-cision shaving removal even with hard-woods and difficult grains. The extremelysmall mouth opening (0.5 mm) and chat-ter-free motion minimise the risk of tear-out. A spring pre-tensioner makes iteasier to adjust the blade and a brassplate protects the sole from wear. The body is made of pear wood finishedwith oil.Blade width 24 mmBlade thickness 2 mmLength 300 mm140 gNo. 702987 80.34 € 95.60 €

J SMALL BENCH PLANEThis compact smoothing plane ispatterned after models manufactured byAustrian company Weiß & Sohn. It feat-ures double blades with a high-qualityHSS cutting edge and an asymmetricalhorn. Suitable for small workpieces.Fine-grained, hardwood (Shun-Gee) body.Cutting angle 45°.Blade width 36 mmBlade thickness 3 mmLength 190 mm682 gNo. 702968 24.62 € 29.30 €Repl. blade No. 702969 9.16 € 10.90 €

A B C

D

E

F G

H I

J

K

Repl. blade No. 703097 8.24 € 9.80 €

Repl. blade No. 703096 8.24 € 9.80 €

Accessories || Scraper blades, Scrapers and putty knife

80

I LEATHER CASEFor protecting sharpened scraper andplane blades from damage. Snap-downflap, belt loop, 4 pockets.Interior dimensions 160 x 80 mm.No. 703549 13.53 € 16.10 €

Scrapers and putty knife

J SCRAPERWhen removing paints, dry residual glueand for restoration projects, these handyscrapers are indispensable aids. The special steel blade, sharpened onone side, is simply inserted in the nickel-plated blade mount. Beech handle.

Width35 mm No. 718220 8.15 € 9.70 € 10 blades No. 718221 6.89 € 8.20 €62 mm No. 718222 10.76 € 12.80 € 10 blades No. 718223 8.91 € 10.60 €

K GLUE SCRAPERFor removing dried, excess glue andscraping away extra varnish. Designedfor heavy-duty use. Solid metal handlefor two-handed use. High-quality,double-edged blade (HRC 60).Blade length 60 mmHandle 315 mmNo. 703161 21.01 € 25.00 €Repl. blade No. 703162 6.64 € 7.90 €

L PUTTY KNIFETraditional German-made putty knife.The hardened, flexibly ground and dry-fined steel blade with a continuous narr-ow tang is attached with a brass clamp toan exotic-wood handle.Blade width 40 mmNo. 718214 15.29 € 18.20 €

Scraper blades

Scraper blades are indispen-sable for smoothing woodensurfaces, removing marksleft by planing and routing,cleaning glued joints and le-velling uneven varnish coats.Sharpened properly and burnished with afine hook, they are capable of removingthe finest shavings and leaving a smooth-er and more precise surface finish than

A FRENCH SCRAPER BLADESSpring steel, approx. 50 HRC, excellent blade durability.

1 Rectangular150 x 50 mmBlade thickness0.25 mm No. 703507 1.76 € 2.10 € 0.4 mm No. 703502 1.76 € 2.10 € 0.6 mm No. 703504 1.76 € 2.10 € 0.8 mm No. 703505 2.02 € 2.40 € 1 mm No. 703506 2.18 € 2.60 €

2 Gooseneck130 x 70 mmBlade thickness0.4 mm No. 703516 3.03 € 3.60 € 0.6 mm No. 703510 3.03 € 3.60 € 0.8 mm No. 703535 3.11 € 3.70 €

Even worn-out Japanese saw bladescan be used to make excellent scraperblades.

3 Scraper sets, 4-piece4-piece sets: rectangular 150 x 50 mm,convex/concave 140 x 50 mm,rounded 140 x 70 mm,gooseneck 130 x 70 mmBlade thickness0.4 mm No. 703517 10.00 € 11.90 € 0.6 mm No. 703518 10.50 € 12.50 € 0.8 mm No. 703536 10.76 € 12.80 €

4 Small scraper set, 3-pieceFor working on small workpieces or in hard-to-reach areas.50 x 25 mmBlade thickness 0.4 mmNo. 703539 2.27 € 2.70 €

5 Mini scraper set, 7-piece7-piece set of small scraper blades madeof Swedish steel.Thickness 0.4 mm27 x 45 mm to 50 x 110 mmNo. 703500 24.12 € 28.70 €

B JAPANESE SCRAPER STEELThe same high-qualitysteel used for Japan-ese saw blades is nowavailable as a semi-finished product. Thesheets are ideal forproducing your ownhigh-quality scraperblades with a long edge life, even when used with the hardest woods.Hitachi steel SK5, basic hardnessapprox. 54 HRC (can be cut and filed).Length 500 mm0.5 x 90 x 500 mmNo. 703523 7.48 € 8.90 €0.7 x 70 x 500 mmNo. 703524 6.55 € 7.80 €

C VERITAS® SCRAPER HOLDERMakes using straight scraper blades ea-sier and reduces the risk of cuts andburns. The scraping blade is tensionedon both sides, holding it particularly se-curely in place. The tension is centrallyadjusted with a screw. Strong, fibreglass-reinforced plastic body with brass fittings.Only suitable for 150 mm, standard-lengthscrapers. Comes with a super-hard, 0.75 mm thick scraper.No. 703527 37.90 € 45.10 €

BurnishersA scraper only performs well when it hasa uniform, sharp hook, usually formed bydrawing a burnisher along the blade’scutting edge.

D TRIANGULAR CROSS-SECTIONFor high burnishing pressure.Steel length 125 mmNo. 703537 12.10 € 14.40 €

E ROUND CROSS-SECTIONWear-resistant HSS steel, hardenedto 64 Rockwell, ground and polished.White beech wood or rosewood handle.

Ø mm1 8 mm No. 703509 11.51 € 13.70 € 2 10 mm No. 703512 11.68 € 13.90 €

F CARB CUT 2Efficient sharpening tool forscraper blades and scraper-type turning tools, with twodifferently shaped hardenedmetal inserts made of dura-ble carbides: a rounded onefor smoothing at normal deformationpressure and a pointed one for high de-formation pressure and larger burrs. For-ged aluminium handle with hand guard.Leather pouch and instructions included.Length 150 mmNo. 703533 24.29 € 28.90 €

For information on sharpening scrapersblades, see our sharpening guide, whichyou can order free of charge.

G VERITAS® VARIABLE BURNISHERSFor safelysharpeningthe edges ofscraper bla-des. The bla-de of thescraper isguided alongan adjustablehardened-steel rod to accurately work its edge. Fibre- glass reinforced plastic body, hardened-steel sharpening rod, angle adjustable from0°-15°. With one 0.6 mm thick blade.No. 703528 31.01 € 36.90 €

H VERITAS® TRUEING GAUGEClamp for flatfiles to facilitatetrueing ofscrapers,saw blades(suitable file:

No. 704901)and even ski edges.90° and 45° fence.Aluminium.Length 140 mmMax. file thickness 5 mmNo. 703526 18.07 € 21.50 €

Locking screw

Scraper bladeDialknob

Carbide rod

0°-15°

File

Scraperblade

A

1

2

3

4

5

B

C

D

E

2

1

F

G

H

I

J

K

L

can be attained by grinding. By varyingthe pressure, angle and curvature of thescraper, you can achieve superb resultseven against the grain (knotty wood, inlays, parquet etc.).We recommend using a fine-grain water-stone for finishing the cutting edge and a diamond stone or fine flat file for levelling and squaring the edge when necessary.

81

Synthetic waterstones | 85

Natural stones | 87

Sharpening stone accessories| 88

DMT®-diamond stones| 88

Quick-sharpeners | 89

Sharpening sets | 89

Sharpening systems | 90

Sharpening accessories | 92

Polishing devices | 92

Rust-removers and protectors | 93

Honing guides | 94

Indispensable!

Sharpening devices

82

The best cutting tool is of little use if it is

not properly sharpened. How to sharpen a

dull cutting edge is a matter of some debate

amongst experts, and their opinions often lie

far apart from each other. We recommend the

technique proven over centuries for the sharp-

est of all cutting edges, the Samurai sword:

Manual sharpening on waterstones. This

method, which is suitable for both knives

and tools, has the following advantages:

• The hardness of the steel does not

deteriorate, as there is no heat generated

• The array of grits allow arbitrarily fine

cutting edges

• As the stones are, by their very nature,

inflexible, exact cutting edge geometries

can be produced (no rounded bevels, as

with felt or rubber discs)

• No danger due to flying sparks

• The basic equipment is not expensive

THE ACHIEVABLE SHARPNESS

DEPENDS ON THE FOLLOWING FACTORS:

- The molecular structure of the steel

Grain size and hardness of the blade

steel (the finer/harder, the sharper)

- The cutting edge geometry

The smaller the cutting angle, the lower

the resistance to cutting

- The grit of the stone

(the finer the grit, the sharper the result)

- The ability of the person using the sharpener

Practice leads to perfection!

NOTHING GOES RIGHT WITH-OUT A KEEN CUTTING EDGE!

WHAT IS SHARPNESS?

Sharpness is defined by the quality of the

intersection of the two bevels which meet at

the cutting edge. Dull blades show a roun-

ding at the cutting edge. Sharpening is there-

fore concerned with the precise abrasion of

material on the bevelled surfaces in order

to obtain a perfect cutting edge again.

THE TEST

Knives:

If you can slice

a ripe tomato

with only the

weight of the

knife and if no

losses arise or

can be seen due

to squashing, you can consider the

sharpening procedure successful!

Tools:

The greatest

challenge for a

woodworking

tool is always

the working of

end grain. Only

truly sharp chis-

els or planes

leave perfectly smooth crosscut surfaces.

DICK PRODUCT RANGE ON THE SUBJECT OF SHARPENING:

- Sharpening stones and accessories

Found here in the catalogue and in

our webshop

- DVDs and books

For self-study

- Sharpening primer

Tips and tricks for sharpening

for order cost-free under

www.more-than-tools.de

- Workshops

One-day workshops / Combined workshops

(infos under www.more-than-tools.de)

- Sharpening service

Experts trained by Japanese sharpening

specialists give your cutting tools breath-

taking sharpness (infos under www.more-

than-tools.de)

SHARPENING DEVICES IN OUR PROGRAMME:

- Synthetic waterstones

Japanese waterstones

Japanese ceramic waterstones

- Natural stones

Japanese stones

Rozsutec stones

Belgian sharpening stones

Arkansas stones

- Diamond stones

- Sharpening machines

- Auxiliary sharpening agents

Cutting edge

Bevel

Bevel angle

Bevel

dull

Abrasion

sharp

Sharpening devices

83

TYPES OF SHARPENING DEVICES The sharpening stones offered can be

classified as follows:

* Japanese synthetic waterstones:

These are the preferred and most effective

stones. They have an open-pore texture with

homogeneous particle intercalation, grind

quickly, and should be trued when wear

sets in.

A new variant is the ceramic waterstone,

with particularly high resistance to wear, for

professional applications.

* Natural waterstones:

Japanese natural stones, as well as Belgian

sharpening stones or the Slovakian Rozsutec

are all based on sediment or limestone with

intercalated corundum, oxides, quartzite, or

semi-precious stones (e.g. garnets).

Due to their slightly inhomogeneous structure,

these harmonise well with hand-forged steels.

Above all, the Japanese and Belgian stones

are becoming increasingly rare.

* Oilstones:

The Arkansas oilstones are very dense and

wear-resistant novaculite. They are well

suited to finishing wood carving and turning

tools.

Note: Do not combine oilstones and

waterstones, as oil counteracts the effect

of waterstones.

* Diamond-»stones«:

With these sharpening devices, the diamond

granulates responsible for the sharpening

effect is embedded in a nickel matrix as a

thin layer on a metallic base. These stones

ensure a high degree of smoothness and long

life, provided that the diamonds are of high

quality (mono-crystalline).

Attention: Avoid low budget products, as

these are mostly made of (short-lived)

poly-crystalline diamond dust.

* Sharpening machines:

For frequent sharpening and repairs, a

water-cooled machine is advantageous.

WHAT BASIC EQUIPMENT DO I NEED?

For beginners:

• Combination stone with grit 1000/6000

(No. 711005) for sharpening and finishing

For advanced users:

• Roughing-out stone with grit 220

(No. 711999) for repairing nicks and

abrading large amounts of steel

• Sharpening stone with grit 1200

(No. 711002) for normal sharpening

• Finishing stone with grit 6000 (No. 711003)

for polishing and removing burrs.

Gouges also require:

• Multiform stone with grit 4000

(No. 711202) for polishing and

removing burrs

For beginners and advanced users:

• Shapton ceramic sharpening stones

(No. 711601 ff.)

For all:

• Trueing block (No. 711299) for the

precise flattening of uneven waterstones

• Sharpening stone holder (No. 711101)

For outdoors, gardens and axes:

• DMT products like DMT Duo

folding sharpener (No. 705391)

HOW CAN I LEARN TO SHARPEN CORRECTLY? • DICK-Workshops

• Sharpening primer under


• DVD (No. 713806)

Sharpening devices

84

WORTH KNOWING

Grit

The grit describes the fineness of a grinding

agent. In Europe, it is defined as the number

of meshes per square inch of a sieve.

Thus, for example, a grinding agent of grit

500 just barely passes through a sieve with

500 meshes per square inch. Occasionally,

the grit is also expressed in terms of the grind-

ing particle size in microns (= 1/1000 mm).

One uses stones of grit 80-220 for roughing

out (coarse shaping, repairing nicks and

chips), grit 800-2000 for sharpening, and

grit 3000-12,000 for finishing and polishing.

Structure of a synthetic sharpening stone

Sharpening stones are always comprised of a

binding agent (matrix), in which the grinding

particles (aluminium oxide, carbide, natural

semi-precious stones, diamond dust) are

embedded. The effectiveness of the stone

depends on the combination of hardness

of the binding agent and the quality of the

grinding particles. As binding agents, clay-

like substances, the hardness of which can

be determined by the composition and the

baking temperature, are used with synthetic

waterstones.

With most Japanese

stones the binding agent

is relatively soft and

open-porous. During

sharpening, fresh

grinding particles are

continuously released,

achieving a high level

of effectiveness.

The wear resulting from this process makes

the regular trueing of the stone necessary.

By comparison, ceramic stones possess a

very hard binding agent and little wear.

In order to obtain good sharpening perfor-

mance, however, the use of high-quality,

wear-resistant grinding particles (such as

with Shapton) is required. In the extreme

case of a completely rigid binding of the

grinding particles, and thus virtually no wear

of the stone whatever, diamonds are used

as grinding particles (DMT).

Why not tool sharpening steel?

This serves only for the removal of burrs from

conventional kitchen knives up to a hardness

of 58 Rockwell. A tool sharpening steel does

not sharpen. Tool sharpening steels have a

hardness of 60 to 70 Rockwell. They would

only scratch Japanese blades or glide use

lessly over the surface. For this reason, we

do not offer tool sharpening steels in our

programme.

Care products

Even after sharpening, every blade still

requires proper care. For the prevention of

rusting, use an acid-free rust-protection oil,

e.g. camellia oil (No. 705280) or Ballistol

(No. 705270). For the cleaning of dull or

oxidised surfaces, we recommend Gundelputz

polishing paste (No. 705262) or Uchiko

polishing powder, and for the removal of rust

the rust eraser (No. 711530).

For the safekeeping of synthetic stones,

we recommend enclosing them in a plastic

container, in which the stones can be kept

in a water bath at all times.

In order to prevent the formation of algae,

add a splash of vinegar or disinfecting agent

to the water bath (caution: aggressive house-

hold cleaning agents can attack the binding

of the stone).

Never subject the stones to frost - danger of

cracking!

With water having a high calcareous content,

it is necessary to prevent frequent drying out,

as the stones would then adulterate, causing

a deterioration of their effectiveness.

Handle the stones with care. Keep them flat,

clean and oil-free (oil prevents the uptake of

water and reduces the grinding effectiveness).

Open texture

Closed texture

Sharpening devices || Synthetic waterstones

85

Synthetic waterstones

The advantagesof Japanese waterstones:

• No overheating of the steel • No rounding of the cutting edges• Wide array of fine grits • High sharpening performance • Water is available everywhere • Completely safe • Ecologically harmless • No messy oil on the blades

Recommendation for a basic tool set:

For beginners: • Combination stone, grit 1000/6000

(No. 711005) for sharpening and honing.

For advanced users:• Coarse shaping stone, grit 220

(No. 711999) for repairing, trueing, etc.

• Sharpening stone, grit 1200(No. 711002) for normal sharpening.

• Finishing stone, grit 6000 (No. 711003) for polishing and removing burr.Needed for gouges:

• Multiform slipstone, grit 4000(No. 711202) for finishing inside channels.

For beginners and advanced users:• Shapton ceramic sharpening stones

(No. 711601ff)

For all:• Trueing block (No.711299) for

precision trueing of water stones.• Sharpening stone holder

(No.711101)

When sharpening one should note thesound and traces on the stone, bothare indicative of the intensity and theuniformity of the contact betweenstone and steel.

Japanese waterstonesExcellent sharpening performance,consistent quality, ease of use and areasonable relationship between priceand performance – these are some ofthe qualities which recommend syntheticsharpening stones. Their soft bond andopen-pored structure allow fresh, sharpabrasives to be continually exposed dur-ing use, resulting in optimal sharpeningperformance. The honing granulate ismade of highly purified metal oxide,carbide and nitride particles bondedtogether in a ceramic or synthetic matrix.The stones are suitable for both Japaneseand European cutting tools and knives.

If necessary, they can be trued withwet abrasive paper on a glass surface,or preferably with a trueing block( No. 711299, p. 88).Prior to use, the stones must be soakedfor 2-10 minutes, or they can be perma-nently stored in water. Instructionsincluded.

Coarse shaping stonesCoarse-grained stones for abrading largeamounts of material. For repairing nicksand chips, altering the bevel geometry,removing corrosion etc.

A GRIT 80, SUEHIRO®

Very aggressive, hard silicon carbidestone. Ideal for trueing other stones.210 x 55 x 27 mm.No. 710990 10.84 € 12.90 €

B GRIT 220, SUN TIGER®

Shaping stone with good sharpeningqualities.

1 With plastic base185 x 63 x 25 mmNo. 711999 24.29 € 28.90 €

2 Bench stone205 x 75 x 50 mmNo. 711000 33.53 € 39.90 €

Sharpening stonesMedium-grit stones for sharpening bluntedges.

C GRIT 800, KING®

207 x 66 x 34 mmNo. 711001 20.08 € 23.90 €

D GRIT 1000, KING® HYPER

No. 711008 44.45 € 52.90 €

No. 711320 50.34 € 59.90 €

F GRIT 1200, KING®

207 x 66 x 34 mmNo. 711002 19.75 € 23.50 €

G GRIT 2000, JINZO®

No. 710991 46.13 € 54.90 €

H CHINESE SHARPENING STONESGood quality sharpening stones at trulyexceptional prices.200 x 50 x 25 mmGrit600 No. 705522 10.00 € 11.90 € 1000 No. 705523 10.00 € 11.90 €

Honing stonesFine-grit waterstones for removing burr,polishing and honing.

I GRIT 4000, KING®

210 x 73 x 22 mmNo. 711021 33.53 € 39.90 €

J GRIT 6000, KING®

185 x 62 x 19 mmNo. 711003 21.76 € 25.90 €

K GRIT 8000, KING® GOLD STONE

No. 711004 40.76 € 48.50 €

L GRIT 8000, AKATSUKI®

No. 711020 64.62 € 76.90 €

Combination stonesWith two different grits.

M GRIT 250/1000, SUN TIGER®

For shaping and sharpening.150 x 50 x 25 mmNo. 711016 14.71 € 17.50 €

N GRIT 1000/3000, SUEHIRO®

No. 711533 10.84 € 12.90 €

P GRIT 1000/6000

1 Sun Tiger®

150 x 50 x 25 mmNo. 711007 19.24 € 22.90 €

2 King®

205 x 50 x 25 mmNo. 711005 29.24 € 34.80 €

3 King®, big207 x 66 x 36 mmNo. 711006 39.41 € 46.90 €

No. 711061 15.04 € 17.90 €

A

High-performance diamond-like abrasiveparticles. Soft bond.205 x 70 x 34 mm

E SHARPENING STONE, GRIT 1000 -EXTRA LARGEIdeal for large knives, wide plane blades,drawknives and blades of all kind.233 x 102 x 70 mm

Good polishing performance withhard bond.185 x 62 x 19 mm

Compact stone with soft bond forsharpening and honing.134 x 40 x 26 mm

For sharpening and honing. Hard bond,little wear.175 x 55 x 25 mm

B

2

1

C

D

E

F

G

H

I

J

K

L

M

N

O

P

2

3

Hard stone with very good polishingperformance, which does not clog easily.For wide blades.205 x 73 x 24 mm

O GRIT 1000/3000, NANIWA®

Do not store this stone in water for a longperiod of time.215 x 75 x 50 mm

1

Sharpening devices || Synthetic waterstones

86

Ceramic waterstones

A SHAPTON® CERAMICSHARPENING STONES

1 Single grains210 x 70 x 10 mm

Grit200 No. 711601 26.81 € 31.90 € 500 No. 711602 33.53 € 39.90 € 1000 No. 711603 39.41 € 46.90 € 2000 No. 711604 46.97 € 55.90 € 4000 No. 711605 52.86 € 62.90 € 6000 No. 711606 58.74 € 69.90 € 8000 No. 711607 73.87 € 87.90 € 16,000 No. 711608 92.44 € 110.00 €

2 3-piece setThree ceramic sharpening stones withgrits 500, 2000 and 8000, incl. sharpening stone holder.No. 711615 175.55 € 208.90 €

Price advantage

3 Sharpening stone holder, Shapton®,without stoneNo. 711610 50.34 € 59.90 €

»Speedy sharp-cutting trio.«Magazine »dds«, 2008

B CERAX® SUPER STONES

1 Combination stone, grit 1000/3000

No. 711024 33.53 € 39.90 €

1 Honing stone, grit 8000210 x 70 x 20 mmNo. 711023 67.14 € 79.90 €

2 Honing stone, grit 10,000With plastic base.210 x 70 x 10 mmNo. 711535 63.78 € 75.90 €

Multiform stonesFor sculptors’ tools and turning tools.

D MULTIFORM STONES, KING®

61 x 22 x 5 mmGrit

1 1000 No. 711204 4.37 € 5.20 € 2 4000 No. 711205 4.96 € 5.90 € 3 8000 No. 711206 6.64 € 7.90 €

E MULTIFORM STONES, KING®

100 x 50 x 10 mmGrit

1 1000 No. 711201 13.87 € 16.50 € 2 4000 No. 711202 16.72 € 19.90 € 3 8000 No. 711203 26.81 € 31.90 €

F MULTIFORM SHARPENING STONE,SUEHIRO®

Ideal for sharpeningand honing of all typesof cutting tools: out-cannel and incannelgouges, V-partingtools. The back side of the stone can alsobe used on chisels.98 x 65 x 20 mm.

Grit1 280 No. 711536 10.84 € 12.90 € 2 1000 No. 711537 11.68 € 13.90 € 3 3000 No. 711538 15.04 € 17.90 €

3-piece setGrit 280 (No. 711536), grit 1000(No. 711537) and grit 3000(No. 711538) in a set.No. 711539 35.13 € 41.80 €

G CONICAL SLIPSTONES, KING®

For gouges. With concave and convexsurfaces.157 x Ø 78 x Ø 12 mm

Grit1 180 No. 711401 25.13 € 29.90 € 2 1000 No. 711402 25.13 € 29.90 € 3 4000 No. 711403 26.81 € 31.90 €

H SLIPSTONE SETS, 2-PIECE,KING®

For carving tools, consisting of:concave stone, radii of 2.5/ 5/8/12/16 mm,size 105 x 65 x 15 mm;convex stone, radii 2/3.5 mm,size 65 x 40 x 6 mm.

Grit1 1000 No. 711208 15.46 € 18.40 € 2 4000 No. 711209 16.30 € 19.40 €

No. 711034 57.98 € 69.00 €

Price advantage

The ceramic sharpening particles ofShapton stones are of high purity and ho-mogeneity. This is noticeable whenchanging over to finer grits: the cuttingtraces from the previous grit are quicklyground out. The base of the sharpeningstone is tempered glass and thus 100%warp-free. A practical advantage: the gritrating on the underside is always visiblethanks to the glass holder.

2 Honing stone, grit 8000Includes a cleaning stone.205 x 73 x 22 mm

Multiform stonesMultiform stones are used to sharpen the cutting edges of sculptor's tools andwood-turning tools. In figure 1, the burr that was created on a gouge during grinding is removed with an 8000 stone.

Figure 2 shows how a 1000 cone stone isused to sharpen a back-bent gouge withinside bevel. To obtain an evenly sharpcutting edge, the sweep and width of thetool must always match the slip stone. Ifthe corners of the gouge have no contact

with the sharpening stone, you can stillsharpen it but you need to move it diagonally.

You cannot sharpen a gouge with the corners touching the stone, as this would

change its sweep. Withcone stones, you can onlyuse a specific part of thecone for sharpening ineach case to avoidchanging the sweep in the process.

For special uses, you canalso grind the multiformstone to the requiredshape on a diamond stone.

1

2

3

1

A

B

2

C

1

2

1 32

D

E

1 32

1

3

2

F

G

1 32

1

2

H

Ceramic stones have a harder bond thanwater stones. This harder bond holds theabrasives tight together. To still ensureeven and effective removal of material,very hard abrasives are used which donot dull so easily. The big advantage ofceramic stones is the even, hard surfaceof the stones, which does not have to betrued as often as water stones but, on theother hand, is more likely to clog.For trueing, we recommend diamondtrueing blocks ( No. 711613 or705382, p. 88). Unlike water stones,you cannot keep ceramic stones in waterall the time; you only bathe them inwater or wet them before use.

Cerax® stones with ceramic abrasiveshave a hard bond and are also highlyabrasive.

For straightforward sharpening and honing of knives in the kitchen area. In plastic box with non-slip rubber base.183 x 63 x 32 mm

C NANIWA®

Ceramic stones made by Naniwa offerhigh polishing performance with hardbond. The stones with grit 8000 or10.000 are suited best for end-polishingof knife blades.

Figure 2Figure 1

Grain Application220 Course shaping500 Flattening

1000 Sharpening2000 Sharpening4000 Sharpening6000 Taking off the burr8000 Finishing and polishing

16,000 Finishing and polishing

Sharpening devices || Natural stones

87

Natural stones

Natural Japanese stones

B BINSUI

No. 711518 33.53 € 39.90 €

D HONYAMA AO

No. 711517 54.54 € 64.90 €

G NAGURA, GRIT 800-1000For cleaning and unclogging the surfacesof sharpening stones and for making afine polishing paste.

1 Natural stoneApprox. 50 x 40 x 30 mmNo. 711301 10.00 € 11.90 €

2 Synthetic72 x 23 x 19 mm.No. 711302 3.28 € 3.90 €

Belgian bench stonesThe quarrying of Belgian stones in the Ardennes is first mentioned in a Romandocument. But the story of these naturalhoning stones goes further back thanthat. The approx. 480 million-year-oldgrey yellow sedimentary stones, originat-ing from volcanic ash, are composed ofvery fine garnet crystals. During honingthese are released and in combinationwith the water and abrasion debris makea honing paste. The garnets only removefine shavings from the metal and ensurea good polish. Unique combination ofspeed and grain size.Interesting fact: To produce 1 kg ofsharpening stones approx. 1500 kg ofcliff must be removed. The thin yellowslices are glued to a slate base and cutto size. Grit approx. 6000–8000.Measurements are approximate.

K BENCH STONE

L FRAGMENTSSize33-39 cm2 No. 705564 15.88 € 18.90 € 48-58 cm2 No. 705565 29.33 € 34.90 €

M FLAT BENCH STONE75 x 30 x 20 mmNo. 705557 13.36 € 15.90 €

N HALF-ROUND SLIPSTONESLength 75 mmWidth (mm)3-7 mm No. 705558 6.64 € 7.90 € 7-12 mm No. 705559 9.16 € 10.90 € 12-15 mm No. 705560 13.36 € 15.90 €

Thicker and longer lasting than thecream-coloured stones, but with equallygood honing properties.

1 Bench stoneApprox. 250 x 60 x 13 mm.No. 705570 39.33 € 46.80 €

2 Multiform stoneApprox. 100 x 40 x 8 mm.No. 705571 10.00 € 11.90 €

A AKA

150 x 45 x 30 mmNo. 711534 10.42 € 12.40 €

220 x 65 x 65 mmNo. 711519 25.13 € 29.90 €

E SHO-HONYAMAA rarity:

No. 711516 117.56 € 139.90 €

F HONYAMA QUARRY STONES

No. 711303 27.31 € 32.50 €

Rozsutec stonesSedimentary sandstone from the Slovakian Mala-Fatra Mountains, idealfor honing. Fine and even grit, high abrasion resistance.

H BENCH STONE200 x 80 x 45 mmNo. 705579 43.61 € 51.90 €

I FLAT BENCH STONE150 x 50 x 20 mmNo. 705580 10.00 € 11.90 €

J DROP-SHAPED80 x 55 x 18 mmNo. 705581 9.16 € 10.90 €

A rozsutec whetstone for sharpeningscythe and sickle blades can be found inthe chapter garden tools.

For sharpening courses see our workshop program or go towww.more-than-tools.de/workshops

Arkansas oil stonesFine grained, extremely wear-resistanthoning stones, for use with an oil lubri-cant. Due to their high degree of hard-ness and stable bond, particularlywell-suited for polishing curved cuttingedges. The stones we offer have a uni-form structure and are crack-free. Theblack stones are somewhat harder thanthe white ones. They originate from quar-ries in the Ouachita Mountains inArkansas (USA) that unfortunately are al-most depleted. Grit approx. 6000-8000.Sizes are approximate.

Q SLIPSTONE SET IN WOOD CASE,WHITE5-piece set: round, square, triangular,oval, knife-shaped.Length 100 mmNo. 705267 50.08 € 59.60 €

R MULTIFORM SLIPSTONE SETS,IN A WOODEN CASE4-piece set: flat-pointed straight back,knife-shaped, flat-pointed round back,flat-skewed round back.6 x 25 x 56 mm

Colour1 White No. 705260 17.82 € 21.20 € 2 Black No. 705261 25.13 € 29.90 €

S HONING OILLight mineral oil for Arkansas and otheroil stones. Also suitable for lubricationpurposes.100 mlNo. 705263 2.44 € 2.90 €

P BENCH STONE, BLACK

»A blade and sharpening stone must beas perfect a match as bride and groom«according to legendary blacksmith, Shi-geoshi Iwasaki. Finding the ideal pairingis no easy task in either case. Despite theexcellent performance of synthetic stones,many experienced sharpeners still prefernatural stones for sharpening their finestblades. Japanese sharpening stones areparticularly renowned for their ability to harmoniously sharpen hand-forged carbon-steels. They can bring a blade’sfull potential to the fore and allow thesharpening process itself to become apleasant ritual.The finest stones from the Honyamaquarries are becoming increasingly diffi-cult to acquire - we take great pleasurein still being able to offer these rare trea-sures. Natural Japanese stones may onlybe used with water and must be keptprotected from frost. Please note that thestones may have slight natural imper-fections and may vary somewhat in size.

C JYO-HAKU

No. 711620 31.01 € 36.90 €

150 x 48 x 20 mmNo. 705258 54.37 € 64.70 €

200 x 48 x 20 mmNo. 705250 67.14 € 79.90 €

150 x 40 x 20 mmNo. 705556 45.80 € 54.50 €

250 x 60 x 25 mmNo. 705555 147.90 € 176.00 €

A

B

C

D

E

F

G

1 2

H

I

J

K

L

M

N

O

2

1

P

Q

R

1

2

S

Coarse sharpening stones, (Nakato)

Medium-coarse grit lime sandstone, veryopen texture, with good honing proper-ties.Grit 800-1000

Medium-grit lime sandstone for generalsharpening. Readily absorbs water, cutswell and easily produces a fine slurry.Grit 800-1200220 x 65 x 62 mm

Fine lime sandstone from the Kuma-moto/Sage region with a dense structureand even grain for intermediate grinding.Grit 1000 - 1500206 x 65 x 35 mm

Fine-grit, grey sedimentary stone from the famous Honyama quarry.Very uniform fine grit for fine sharpeningpurposes. Synthetic base.Grit 1000-2000185 x 58 x 38 mm

Honing stones, (Awasedo)

Very fine-grit stone cut from a thin stra-tum of sedimentary rock at the Sho-Ho-nyama quarry. Unparalleled for honingand polishing hand-forged chisels, planeblades and carbon-steel knives. Mountedon a wooden base.Grit 6000-8000200 x 72 x 22 mm

Natural fragments, planed flat on oneside. From the point of view of sharp-ening properties comparable with goodBelgian bench stones.Grit approx. 6000-8000Approx. 100-140 x 70-90 x 10-20 mm

Cleaning stones, (Nagura)

O BLUE BENCH STONE

The US-based company Diamond Mach-ining Technology, Inc. (DMT) is the leading manufacturer of quality diamondsharpening stones. DMT tools are preci-sion manufactured, highly wear resistantand extremely effective. The monocrystal-line diamonds*, permanently embeddedin a nickel matrix, guarantee remark -able sharpening speed even when work-ing the hardest tool steels. The diamond-coated blocks remain permanently plane,and are especially suitable for tools withstraight blades as well as for producingplane surfaces (e.g. backs of plane andchisel blades, plane soles, scrapers).Also suitable for carbide coated cutters,HSS, as well as non-metal materials(glass, ceramic etc.). We recommendmoistening the DMT stones with waterand grinding with little pressure.

* Monocrystalline diamonds are signifi-cantly more wear resistant than the poly-crystalline diamonds used to make lesserquality diamond sharpening tools.

Sharpening devices || Sharpening stone accessories, DMT-diamond stones

88

Sharpening stone accessories

A STONE HOLDERFrom stainless steel with anti-slip rubberclamping jaws and medium supportbracket, in order to avoid breakingthin stones.Opening 220 mmWidth 70 mmNo. 711101 20.59 € 24.50 €

B ANTI-SLIP BLOCKSSlip-resistant rubber base for sharpeningstones. 2-piece set.93 x 87 x 15 mmNo. 711102 8.32 € 9.90 €

C ANTI-SLIP MATPrevents sharpening stone slippage.100 x 250 mmNo. 705364 3.78 € 4.50 €

F TRUEING BLOCKSHard ceramic blocks fortrueing Japanese water-stones quickly and ac-curately. The stones areworked wet on the blockuntil plane. The use of silicon carbidepowder speeds up the process.

G TRUEING BLOCK WITH DIAMONDCOATING

No. 711613 209.24 € 249.00 €

E TRUEING BLOCKContinuous surface diamond coating oncompact base plate. Ideal for dressingwater- or ceramic based stones. Rubberfeet.Grit 120 µm, grit approx. 120 (extra-extra coarse).203 x 76 x 10 mmNo. 705382 63.03 € 75.00 €

H TRUEING GRILLE FOR SHARPENINGSTONESFinely woven, siliconcarbide-coated grille fortrueing uneven sharp-ening stones. The grilleis placed on a flat sur-face and the wateredwhetstone is rubbedover it in a circular motion.140 x 230 mmNo. 711297 4.12 € 4.90 €

DVD - DAS SCHÄRFEN JAP. MESSERA Japanese masterblacksmith with a leg-endary reputation inJapan shows you howto professionally sharp-en kitchen knives onwater stones. He intro-duces different typesof whetstone, shows the correct sharp-ening motions for sharpening single anddouble-bevelled knives and provides information on caring for knives. Knivessharpened in this way not only make yourwork easier but are also a pleasure to useand allow you to treat your food with respect. In German.DVD, 15 min.No. 713806 4.96 € 5.90 €

D SHARPENING STONE HOLDERFOR THE SINKThis sharpening stone holder, made of stainless steel, is positioned in the sinkwith two straps cus-hioned with rubber on the sides and atthe top. The slidable fixture at the top allows sharpening stones of differentlengths (190 - 270 mm) to be clamped.Fits in sinks with inside dimensions of 315-560 mm.Width 130 mmNo. 711035 97.39 € 115.90 € 1 170 x 55 x 30 mm

No. 711298 14.20 € 16.90 €

2 240 x 100 x 40 mmNo. 711299 55.38 € 65.90 €

DMT® diamond stones

J DMT® DUO SHARP COMBINATIONSHARPENING STONESDiamond stone with two opposite plates ofdifferent grains. The stress-free sandwichconstruction guarantees flatness. Excellentfor trueing (blade backs, other sharpeningstones) and for sharpening cutting edges ofall kinds.

K DUO SHARP PLUS (SET)Double-sided Diamond Sharpening Tool,incl. mount.203 x 67 x 9.5 mmNo. 705372 91.60 € 109.00 €

L MOUNT FOR DUO SHARP

No. 705399 16.72 € 19.90 €

I SHARPENING STONESFor knives and tools. Plastic case,slip-proof rubber base.152 x 50 x 19 mm

Grit1 extra co. No. 705365 44.45 € 52.90 € 2 coarse No. 705366 44.45 € 52.90 € 3 fine No. 705367 44.45 € 52.90 € 4 extrafine No. 705368 44.45 € 52.90 €

M TRUEING BLOCKSContinuous surface diamond coating oncompact base plate. Ideal for pointedtools or accurately trueing the backs oftools. Rubber feet.

po lycrys tal linemo no crys tal line

Fits No. 705375, 705371 and 705370.Stable plastic, handle on underside, anti-slip rubber pad.311 x 117 x 57 mm

A

B

C

D

E

F

1

2

G

H

I

1

2

3

4

J

K

L

M

Fine / coarse250 x 100 x 9.5 mmNo. 705375 137.82 € 164.00 €

Fine / coarse203 x 67 x 9.5 mmNo. 705371 88.24 € 105.00 €

Coarse / extra coarse203 x 67 x 9.5 mmNo. 705370 88.24 € 105.00 €

Extra extra fine203 x 76 x 10 mmNo. 705389 58.74 € 69.90 €

Extra fine203 x 76 x 10 mmNo. 706281 50.34 € 59.90 €

Fine152 x 51 x 6 mmNo. 705380 26.89 € 32.00 €

Fine203 x 76 x 10 mmNo. 705381 50.34 € 59.90 €

Extra extra coarse203 x 76 x 10 mmNo. 705382 63.03 € 75.00 €

For ultra precise trueing. Suitable for all water and ceramic stones.(Tolerances +/-4 micron).253 x 80 x 24 mm

Extra-extra coarse (silver) (grit size 120 µm) Grit~120 for trueing.

Extra coarse (black) (grit size 60 µm) Grit~220 for coarse shaping, trueing.

Coarse (blue) (grit size 45 µm) Grit~325 for coarse sharpening.

Fine (red) (grit size 25 µm) Grit~600 for sharpening, honing.

Extra fine (green) (grit size 9 µm) Grit~1200 for sharpening, honing.

Extra extra fine (brown) (grit size 9 µm) Grit~8000 for honing.

Nickel-embedded diamonds

Recesses prevent swarffrom clogging the stone.

Polycarbonate ormetal base. Steel

plate

Sharpening devices || DMT-diamond stones, Quick-sharpeners, Sharpening sets

89

C DMT® MINI-POCKET WHETSTONEThe sharpener for onthe go. Folding case,key ring, fine grit.70 x 25 x 5 mm.No. 705395 11.68 € 13.90 €

A DMT® ALL-PURPOSE SHARPENERIN FOLDING CASE

B DMT® MINI WHETSTONEIdeal for on the go:In a leather sheath, excellent for quicklysharpening router bits, small tools andknives. Körnung fein.111 x 23 x 5 mm.No. 705386 22.69 € 27.00 € F DMT® DIA-SHARP MINI-HONE

KIT - COARSE, FINE, EXRA-FINEThe hone-kit for all contingencies:Tight spaces? No problem! The Dia-SharpDiamond Mini-Hone Kit, made by DMT®,convinces through ergonomically designedhandles and its compact size (each filemeasures 18 x 1,8 centimeters). The coarse honing file (325 grit) sharpens dull blades easily, the fine file (600 grit) hones blades to razor sharp-ness, while the extra-fine file (1200 grit)polishes and adds the finishing touch to any blade. Not only knives but also pruning shears of all kinds and evenwoodworking tools with carbide insertscan be sharpened. Sharpening is fast andeasy, either with some water or without. 180 x 18 mmGrit 325, 600 and 1200No. 706282 20.92 € 24.90 €

G DMT® ROUND FILEFor gouges, profiled blades, turning tools,tool making etc. Conical cross-section.Ø 3.3-9.5 mmFile length 100 mmFine gritNo. 705392 25.88 € 30.80 €

H DMT®-DIAMOND CHAINSAW FILEDiamond coatedround file for finishsharpening of sawlinks, also very suit-able for gouges, pro-filed blades etc.High efficiency atlow levels of applied force, even with thehardest steels.File length 95 mmØ mm4 mm No. 705360 25.97 € 30.90 €4.8 mm No. 705361 25.97 € 30.90 €

D DMT® DIAMOND HONING CONESConical diamond sharpener for sculptorand turning tools. Fine grit.Ø 9.5-19.3 mmLength 152 mmNo. 705393 29.33 € 34.90 €

E DMT® SHARPENING CARDSharpening plate, credit card-sized. Finegrit.82 x 51 x 1 mmNo. 705396 10.84 € 12.90 €

Further information on diamondsharpeners and on sharpening in generalcan be found in our Sharpening Primer,supplied free of charge on requestat www.more-than-tools.de

Quick-sharpeners

I TOKICO® KNIFE SHARPENERAn uncomplicatedknife sharpener thatis suitable for bothJapanese and Euro-pean knives. Easyto operate, the Tokicoallows even inexperi-enced users to quickly and successfullysharpen all types of cooking knives.The blade simply needs to be moistenedand slid 3–5 times in both directionsthrough the slits. Metal is gently removedby two rotating and correctly angledstones. Suitable for single and double-sided ground knives.Please note: The Tokico is not suitablefor damaged or worn out blades.200 x 45 x 40 mmNo. 705373 18.15 € 21.60 €

J CARBCUT 1For speedy re-sharpeningof knives (also serrated),axes and scissors, ideal foron the go. The V-form,wear-resistant carbideelement is also suitablefor removing shavings as well asdeburring. Forged aluminium grip withhand protection. Includes instructionsand case.Length 150 mmNo. 703534 21.68 € 25.80 €

K CARBEE® POCKET SHARPENERThis handy all-purpose sharpener hasa hard metal sharpening head withtwo V-form corners as well as a flat riffledside for subsequent blade polishing.For dry working, without water or oil.Overall length 82 mmNo. 703538 9.16 € 10.90 €

Sharpening sets

L KNIFE SHARPENING SETBasic set for sharpening and mainten-ance of knives and tools. Set includes:Cerax Super Combination Stonegrit 1000/3000 (no. 711024);DVD - Das Schärfen japanischer Messer(No. 713806), in German;Sinensis Chinese camellia oil(No. 705280).No. 711027 39.08 € 46.50 €

Price advantage N UNIVERSAL SHARPENING KITThe basic equipment for sharp knivesand tools. This collection of high-qualityproducts includes all the basic equip-ment for sharpeing knives and tools. Theincluded Sharpening brochure gives in-structions on how to proceed. Have fun!Kit includes:Japanese combination stone king,1000/6000 grit (711007);Non-skid mat (705364);DMT® sharpening file (705374);Sinensis Chinese camellia oil(705280);Sharpening primer.No. 711029 40.17 € 47.80 €

M COMBINATION SHARPENING STONE,WITH STONE HOLDERFor sharpening and finishing.1000/6000 grit205 x 50 x 25 mmNo. 711050 41.93 € 49.90 €

For sharpening out-door knives, gardenequipment, axes,shears or hard-metalmachine tools. The foldable grip servesboth as a protective sleeve for the diamondplate and while in storage. Single or dou-ble-sided coating.110 x 23 mm

1 Extra fine / extra extra fineNo. 706284 41.93 € 49.90 €

2 Extra fineNo. 705384 20.76 € 24.70 €

3 FineNo. 705369 20.76 € 24.70 €

4 CoarseNo. 705374 20.76 € 24.70 €

5 Fine / coarseNo. 705391 38.57 € 45.90 €

A 1

2

3

4

5

B

C

D

E

F

G

H

I J

K

L

M

N

Further DMT-products at ww.more-than-tools.de

Sharpening devices || Sharpening systems

90

Sharpening systems

Tormek® sharpening system

Learn the professional use of theTormek machine. If you buy a Tormek T-7you may take part in a special course»Sharpening with Tormek« free of charge.Further information on the internet under www.more-than-tools.de/workshops

A TORMEK T-7»Tormek-Original« sharpening stone,grit 220, Ø 250 x 50 mm; leather honingwheel Ø 215 x 30 mm; universalsupport, finely adjustable (can be usedhorizontally or vertically). Powder coatedsteel plate housing.220 V, 200 W, 90 RPM, 16.8 kg.Includes:Precision 90° jig (SE 76)Adjustable trueing tool (TT 50)Stone preparer (SP 650)Angle gauge (WM 200)Honing paste (PA 70)Handbook (HB 10)Instruction video, (DVD-1),Workshop »Sharpening on the Tormek«No. 705191 444.54 € 529.00 €Tormek original repl. wheel (SG-250)No. 705201 116.81 € 139.00 €

B TORMEK T-3»Tormek-Original« sharpening stone,grit 220, Ø 200 x 40 mm; leather honingwheel Ø 145 x 26 mm; universal supportwith fine adjustment (horizontal and ver-tical settings). ABS plastic housing.220 V, 120 W, 120 RPM, 7.3 kg.Includes:Precision 90° jig (SE 76)Angle gauge (WM 200)Honing paste (PA 70)Handbook (HB 10)Instruction video, (DVD 1)No. 705185 273.95 € 326.00 €Tormek orginal repl.wheel (SG-200)No. 705196 77.23 € 91.90 €

Tormek® AccessoriesSuitable for models 2000-2006, 1200-1206, T-3 and T-7 unless otherwisenoted.

C KNIFE JIGS(SVM 45) - Width 45 mmBlade length min. 60 mmNo. 705203 27.65 € 32.90 €

(SVM 100) - Width 140 mmBlade length min. 160 mmNo. 705214 38.24 € 45.50 €

D SCISSORS JIG (SVX 150)Also suitable for hedge shears.No. 705205 33.53 € 39.90 €

E PLANER/JOINTER JIG (SVH 320)For blades of any length, minimumblade width 13 mm.No. 705207 125.21 € 149.00 €

F TOOL REST (SVD 110)For turning tools (scrapers, scorps,inshaves) chisels, scraper blades etc.»Torlock« locking system.No. 705218 24.79 € 29.50 €

G GOUGE JIG (SVD 185)For turning and firmer gouges, as well ascutters for hollowing tools etc., up to25 mm wide. Adjustable in width,cutting angle and shape.No. 705247 60.92 € 72.50 €

H TURNING TOOL SETTER (TTS 100)For adjusting angle bevels of turning gouges and chisels, independent of wheeldiameter. Used in combination with jigs(SVD 185) and (SVS 50).No. 705237 16.47 € 19.60 €

I PRECISION 90° JIG (SE 76)For plane blades and chisels. Also suit-able for Japanese chisels, for Tormek T3,T7 and old series models,(included with T-7 and T-3).No. 705236 45.29 € 53.90 €

J AXE JIG (SVA 170)For axe heads up to 170 mm in size (larger axes can be sharpened without a jig using the universal support).No. 705228 11.43 € 13.60 €

K PROFILED LEATHER HONING WHEEL(LA 120)For honing and polishing the inside ofgouges and V-shaped tools, interchange-able wheels.No. 705227 40.25 € 47.90 €

L MULTI JIG (SVS 50)Universal jig for turning tools andcarving gouges with straight andcurved cutting edges and for skewand straight chisels.No. 705229 41.93 € 49.90 €

C

D

E

F

G

H

I

J

K

L

A

B

Proven for many years and constantlyperfected wet-working sharpening ma-chines are the basis of the ingeniousTormek-sharpening system. A range ofjigs, which can be mounted on the uni-versal support, makes the sharpening ofany cutting tool easier. Tormek enablesthe achievement of exact cutting geo-metry and consistent results for chisels,turning tools, knives, shears or machinetools. Also suitable for workshops and in-structional settings because of safe oper-ation – no sparks are produced and it hasan overload safety clutch. The »Tormek-Original« ceramic wheel assures short sharpening times under allconditions in combination with the great-est possible tool protection. The frontend can also be used for plane honing.The leather honing wheel removes burrsquickly and leaves a perfectly polishedcutting edge. Designed for continuousoperation (T-7) with solid housing andsliding water container.

A summary of the advantages ofthe Tormek T-7 and T-3 sharpeningmachines:

Longer working life:

• Stainless steel spindle with EzyLockSystem for easier stone assembling

• Better motor insulation• Electrophoretic dip painted casing

(T-7)• Improved water container with

magnetic dirt collector, overspillrim and drip-off plate (T-7)

• 2 additional rubber feet to drainoff water on the case (T-7)

• 7-year guarantee!

Sharpening devices || Sharpening systems

91

A SHORT TOOL JIG (SVS 32)For short gouges, and V blades.Blade length min. 45 mmBlade width max. 32 mmNo. 705239 15.55 € 18.50 €

B ADJUSTABLE TRUEING TOOL (TT-50)With diamond tip, for trueing ingrainedor unround grinding wheels.No. 705210 56.22 € 66.90 €

C DUST COVER (MH 380)Linen, to protect from wood dust.No. 705215 14.20 € 16.90 €

D STONE GRADER (SP 650)For regrading and dressing Tormeksharpening stones.No. 705209 17.56 € 20.90 €

E TURNING ACCESSORIES PACK(TNT-708)

No. 705454 209.24 € 249.00 €

F HOME ACCESSORIES KIT (HTK-705)Short jig,axe jig,knife jig,long knives jig,scissors jig.No. 705455 115.04 € 136.90 €

H BENCH GRINDER MOUNTING SET(BGM-100)

No. 705225 43.61 € 51.90 €

Tormek replacement parts can be found on the Internet at www.more-than-tools.de

G STONES FOR T-3Fits models 1200-1206 and T-3.Approx. Ø 200 x 40 mm, bore 12 mm.

1 Tormek orginal replacement wheel(SG-200), grit 220This hard-bond stone is suitable forpre-sharpening 2-layer blades as wellas chromium-vanadium steel and HSS.No. 705196 77.23 € 91.90 €

2 Japanese sharpening wheel, grit 1000Suitable for HSS as well as carbon-steeland 2-layer steel. Hard bond for highlyeffective polishing with little abrasion.

No. 716040 100.00 € 119.00 €

3 Tormek honing wheel (SJ 200),grit 4000Extreme polishing performance for mirrorsurfaces, thanks to hard bond. Particu-larly recommended for chromium-vana-dium steel but also for HSS blades and2-layer steel.No. 705458 131.09 € 156.00 €

I STONES FOR T-7Fits models 2000-2006 and T-7.Approx. Ø 250 x 50 mm, bore 12 mm.

1 Japanese sharpening wheel,grit 80

No. 716030 100.00 € 119.00 €

2 Tormek orginal replacement wheel(SG-250), grit 220This hard-bond stone is suitable for pre-sharpening 2-layer blades as well aschromium-vanadium steel and HSS.No. 705201 116.81 € 139.00 €

3 Tormek sharpening wheel blackstoneSilicon (SB 250), grit 220

No. 705456 129.41 € 154.00 €

4 Japanese sharpening wheel, grit 800Fast and effective with soft bond, for 2-layer blades, carbon-steel. Also idealfor grinding chromium-vanadium steel,for example Pfeil sculptor's gouges.No. 716060 158.82 € 189.00 €

5 Japanese honing wheel,grit 4000This stone has a softer bond and ishighly effective. Suitable for HSS steelas well as for 2-layer-blades and carbonsteel.No. 716061 192.44 € 229.00 €

6 Tormek honing wheel (SJ 250),grit 4000

No. 705457 175.55 € 208.90 €

Sharpening-workshops

Learn the professional use ofthe Tormek machine. If you buya Tormek T-7 you may take partin a special course »Sharpeningwith Tormek« free of charge. Further information on the internet atwww.more-than-tools.de/workshops

For additonal sharpening workshops»Sharpening Of Cutting Tools« or»Sharpening Of Kitchen Knives« see our workshop programm at www.more-than-tools.de/workshops

A

B

C

D

E

F

H

G

1

2

3

1

2

3

4

5

6

I

Gouge jig, multi-jig ,tool rest, leather honingwheel, turning tool set-ter, machine dust coverand instructions box forturners.

Extra-coarse stone with hard bond for re-pairing damaged tool blades. Primarilysuitable for 2-layer blades and carbonsteel.

Extreme polishing performance for mirrorsurfaces, thanks to hard bond. Particularlyrecommended for chromium-vanadiumsteel but also for HSS blades and 2-layersteel.

Though primarily designed for turners,this mounting set, in combination withthe Gouge Jig (SVD-185), the Multi Jig(SVS-50) and theTool Rest (SVD-110), allows youto use all turningtools with theTormek systemalso on a double-wheeled bench grinder.This makes the rough pre-sharpening of hard steels much easier. Using theturning-tool setter, you can transferthe same blade geometries to the Tormekmachine for honing. Comes with Tormekuniversal support with fine adjustment,English guide to sharpening turningtools, and instructions for building a plat-form for the double-wheeled grinder.

Ideal for exceptionally hard materialssuch as HSS, but also carbon-steel. Thehardness, shape and size of the abrasivemake it highly effective.

Sharpening devices || Sharpening systems, Sharpening accessories

A SHINKO® SHARPENING SYSTEM

Repl. stone, Grit 280No. 716021 41.93 € 49.90 €Repl. stone, Grit 1000No. 716022 50.34 € 59.90 €Repl. stone, Grit 6000No. 716023 54.54 € 64.90 €

SHINKO® SHARPENING SYSTEM,SETSystem, incl. 3 waterstones.(grits 280, 1000 and 6000).No. 716024 217.65 € 259.00 €

Price advantageNo. 716020 167.23 € 199.00 €

Sharpening accessories

B STEEL LAPPING PLATEMilled steel plate for lapping the backsof chisels and plane blades. Needs to bescrewed to a wooden base. The blade isworked with the help of a piece of woodapplied with pressure. Used with siliconcarbide powder and water.240 x 60 x 7 mmNo. 713600 20.92 € 24.90 €

C STROPSThese strops can be used with or withoutpaste to polish tool blades. The solid,non-slit beech base prevents cuttingedges from being rounded off. If neces-sary, you can use finishing paste on theblack (rougher) side; the fine brown sideis usually used for stropping withoutpaste.

1 2-sided paddle stropCan be held by the handle or screwed toa worktop through the two holes.415 x 75 x 18 mmNo. 709162 31.85 € 37.90 €

2 4-sided paddle stropAs well as the two regular leather sides,this strop has two more sides with differ-ent types of leather whose grade is indi-cated on the block by a point system(1 = rough to 4 = fine). Ideal for use withdifferent sharpening pastes. Can be heldby the handle or fixed to the worktop be-tween bench dogs.310 x 40 x 40 mmNo. 709163 41.93 € 49.90 €

Polishing devices

D FELT POLISHING WHEELS ANDBUFFING WHEELSFor machine polishing and honing of cutting edges, especially for knife bladesand carving tools. Use with polish paste.Max. rotary speed 3600 RPM150 x 20 mmBore 20 mm

1 Felt buffing wheelExtra hard, wear-resistant felt for minorrounding off of sharpened edges.No. 705490 20.92 € 24.90 €

2 Felt buffing wheel, straight – mixed wool feltSmoother felt, takes more polishingpaste, enables more intense abrasion.No. 705493 12.18 € 14.50 €

3 Felt buffing wheel, rounded off – mixed wool feltWith rounded edges, particularly suitablefor work on grooves.No. 705494 15.88 € 18.90 €

4 Buffing wheel – multi-coloured clothApprox. 40 layer cloth, double sown.No. 705495 5.46 € 6.50 €

5 Buffing wheel - sisalApprox. 70 layers of especially evenlywoven sisal, double sown, for finepolishing.No. 705496 13.36 € 15.90 €

E SPUR FOR FELT AND BUFFING WHEELSFor chucks, with wheels, nut and adaptersleeve Ø 20/8 mm.No. 705491 7.48 € 8.90 €

F SILICON CARBIDE POWDERUse this powder to true up and polishthe back of chisels blades and bladesof planes. Put a small amount of powdermixed with a drop of water onto an evensteel plate. Now grind the iron until youget an even surface and consistentmicrosection. 150 gGrit50 No. 713603 3.95 € 4.70 € 180 No. 713604 3.95 € 4.70 €

G DMT® DIAMOND POLISHING PASTE,SETFor mirror-finish polishing of knives, cut-ting and plane blades. Put 2-3 drops ofdiamond paste on a metal, glass or hard-wood surface and then polish applyingeven pressure. Begin with a grit size of 6micron and continue the polishing with adiamond paste of 3 and finally 1 micron.Set contains 3 syringes of paste with gritsizes 6 (5 g), 3 and 1 (2 g).No. 705400 16.39 € 19.50 €

H GUNDEL-PUTZ® POLISH ANDWHETTING PASTEProven cleaning and polishing agent forall shiny metals (steel, stainless steel,aluminium, brass, copper, silver, gold, nickel, chromium etc.). Ideal for honingblades on leather, e.g. Tormek sharp-ening system, strops, etc. Non-toxic, acid and formaldehyde-free. 100 mlNo. 705262 4.96 € 5.90 €

I POLISHING PASTES

Grit1 Coarse No. 705265 3.28 € 3.90 € 2 Medium No. 705264 3.28 € 3.90 € 3 Fine No. 705266 3.28 € 3.90 €

J JAPANESE POLISHING POWDER -KONGOSAFor polishing knifeblades, tool mirrorsurfaces and removingoxide layers. Usedwith addition of water.Grit approx. 100050 gNo. 716363 5.46 € 6.50 €

K JAPANESE POLISHING POWDER -SUITAMade from natural sharpening stones,this finishing powder should be appliedafter initial polishing with Kongosa.Grit approx. 800050 gNo. 716364 7.31 € 8.70 €

A

B

C

1 2

D

1

2

3

4

5

E

F

G

H

I

1 2 3

J

K

Shinko® sharpening system

92

The Shinko grinder enables the achieve-ment of professional sharpening results.Clogging rarely occurs with the open-pored Japanese waterstones. Water cooling and plane-honing produces long-lasting and strong edges. Becauseno heat is generated, the blade can beheld very close to its edge and guidedvery accurately. No sparks are produced,allowing the device to be safely operatedin workshops and instructional settings.The stone surrounding foam ring is easilypressed down when sharpening long blades.

Sharpening wheel:Japanese waterstone, grit 1000, Ø 180 x Ø 70 mm, thickness 20 mm,steel mount, wheel nut, splashguard.Motor:220 V, 125 W, 50/60 Hz, 450 RPMgear-driven.Casing:Plastic, tool rest adjustable in height andangle. Water container with valve, draintube. Overall weight approx. 5.5 kg.

These wax-like polishing pastes are appliedto felt buffing wheels and smooth leathersides of strops. No. 711530 only forsteel/stainless steel, 711531 and 711532also for aluminium.35 x 45 x 80 mmApprox. 180 g

Sharpening devices || Sharpening accessories

93

Rust-removers and protectors

A RUST ERASERThese rubberised abrasive blocks providean effective means of removing surface rustfrom valuable kniveswithout damaging theblades. Using water as a lubricant, the rust is»erased«. The blocks are alsoexcellent for removing tough stainsfrom pots, taps, sinks, antiques andautomotive parts.65 x 40 x 9 mm

Grit1 Coarse No. 711530 5.80 € 6.90 € 2 Medium No. 711531 5.80 € 6.90 € 3 Fine No. 711532 5.80 € 6.90 €

B RUST REMOVEREffective anti-rust formula:Even if you own tools, which are completelycovered with rust, it may not be too latefor them. This Rust Remover is the solution to this problem. Simply mix thenon-acidic formulation with water andsubmerge your rusty tools. It won't attackplastics, rubbers and wood. The formulais biodegradable, 500 milliliters makeup a solution of ten liters for rust remover.After the initial rust has been removed,the tools are protected from further corrosion.Content 500 mlNo. 705487 29.33 € 34.90 €

C RUST REMOVER, GELAre you tired of using rusty tools? Withthis gel-like rust remover you can removerust easily and quickly. Apply the undilutedgel on the surface with a kitchen spongeand simply rub off the rust. Can also beused for large surfaces. This gel does not stain wood and most synthetic substances. Bio-degradable.Content 250 mlNo. 705488 19.24 € 22.90 €

D WATER STONE ADDITIVEThis product protects all kinds of steelwhich are exposed to grinding fluid.Every knifemaker knows the followingsituation: While grinding you get inter-rupted and when you return later theblade shows signs of rust. With this addi-tive, which may be used with all waterstones and diamond sharpening systems,rust is not a problem anymore. Whetheryou sharpen manually or by means ofyour Tormek, the sharpening stone doesn't suffer damage and the tool istemporarily protected. Simply mix withgrinding fluid, 250 ml make up into6 litres of non-corroding honing fluid.Biodegradable.Content 125 mlNo. 705485 10.84 € 12.90 €

E VCI TOOL GUARD, 3 PIECE SETVCI means »vapour phase corrosioninhibitor«. A chemical agent votalitisesand molecularly adheres to metal surfacesinside drawers or tool cabinets whichneed to be protected against corrosion.This chemical agent is perfectly suited toprotect difficult to access hollow spaces,internal screw threads and boreholes.The applied coating protects againsthumidity, filth, salts and oxygen. All youhave to do is to take the lid off and toput the open can inside confined spaceswhich need to be protected. The back ofthe can features an adhesive strip. Eachcan will provide up to 12 months pro-tection in volumes up to 0.056 m²(capacity around 50 liters).Durable if closed.Diameter: 35 mmNo. 705483 14.20 € 16.90 €

F WAX POLISHThis Wax Polish protects plane solesmade of steel and other flat surfacesfrom rust and at the same time reducesfriction. Equally suited for cast-iron, steeland iron. It also inhibits the tarnishing ofpolished copper, brass and bronze items.Apply Wax Polish sparingly with cloth,then polish.Content 100 mlNo. 705484 11.68 € 13.90 €

G ANTI-CORROSION COATINGThis anti rust coating, which complieswith military standards, gives superbprotection from corrosion to all metals.Once applied, the non-yellowing filmprotects for up to two years.Shake well before use and applywith brush, cloth or spray.Can be wiped off easily.Content 125 mlNo. 705486 10.00 € 11.90 €

H SINENSIS® CAMELLIA OILVersatile, light oil from the seeds of thecamellia tree:Corrosion protection: Camellia oil is acid-free, not volatile and not susceptible toresinification, making it the ideal oil toprotect tools from rust. Made from purenatural plant products and food safe, it is especially suited for the preservationof kitchen knives made of carbon-steel.Wood protection: When applied to wooden surfaces, it is absorbed quicklydue to its low viscosity. Once absorbed,it helps protect the wood from damage by moisture, dirt and UV light. Clear, notdiscolouring, it accentuates the wood’snatural beauty.Body care: Camellia oil makes an excel-lent base for the preparation of lotions,creams and soaps for cosmetic use.

Content1 100 ml No. 705280 3.45 € 4.10 € 2 250 ml No. 705281 5.21 € 6.20 € 3 1000 ml No. 705282 11.43 € 13.60 €

I JAPANESE CAMELLIA OILThe unalloyed carbon-steel which most-high-quality blades are made of is notcorrosion-free. To protect them from rust,occasionally apply a thin coat of light,acid-free, non-evaporating oil. This extremelylight oil is extracted from the leaves of the camellia tree. Just a thin coat will reliably protect a steel blade from corro-sion. Camellia oil is not susceptible to resinification and may also be used forcleaning, sharpening and lubrication purposes. Not suitable for direct contactwith food and kitchen knives. For thatpurpose we recommend the pure ChineseCamellia oil (No. 705280)

Content1 100 ml No. 713800 4.71 € 5.60 € 2 250 ml No. 713801 5.80 € 6.90 €

J BALLISTOL®

Ballistol provides reliable rust protection,cleans and oils metals, impregnatesand preserves leather and wood surfaces,and is even suitable for the disinfectionof minor cuts. In the garden it can beused to treat tree cancer and to combataphids (in a 3% solution with water).Ballistol is based on pure medical whiteoil, spiked with natural plant products.It is thus ecologically-friendly and bio-degradable.

Content

1 Glass bottle 50 ml No. 705270 2.77 € 3.30 €2 Spray bottle 200 ml No. 705445 7.48 € 8.90 €3 Storage container 500 ml No. 705440 11.85 € 14.10 €

K SPRAY BOTTLE (EMPTY)250 mlNo. 705441 5.80 € 6.90 €

L JAPANESE RUST-PREVENTION OILIdeal for badly corrodedblades such as gardenshears, sickles, branchsaws or outdoor knives.Greases, protects fromdirt and is also suitablefor the removal of surfacerust.60 mlNo. 711541 5.80 € 6.90 €

M OIL POT (ABURATSUBO)

No. 713810 9.16 € 10.90 €

N BAMBOO ABURATSUBOBamboo container with lid (contents notincluded). Filled with cotton wads it canbe used as an Aburatsubo, or for thestorage of small and valuable objects.Approx. 50 x 110 mm.No. 713812 3.78 € 4.50 €

Oil pot, including wads, fitted witha wick. For protecting blades and forgreasing when chiselling out mortises.Use with camellia oil (not included).Capacity 100 ml

Before derusting

After derusting

A 1

2

3

B

C

D

E

F

G

H

321

I

J

321

K

L

M

N

1 2

H WOLVERINE SHARPENING SYSTEMThe Oneway® sharpening system wasspecially designed for woodturning toolsbut, with its two different jigs, is alsosuitable for chisels and plane bladesas well as other tools. The arm is fittedto a double-wheeled grinder using a basesystem (fits all common models).

Sharpening devices || Sharpening accessories

94

Honing guidesFor clamping and precise-angle sharpen-ing of chisels and planes on benchstones. Minimum blade length 60 mm.Limited applicability for sharpeninghand-forged (e.g. Japanese) tool blades.

A VERITAS® SHARPENING SYSTEM IClamp the blade in the jig and set thedesired bevel angle using the angle jig.The sharpening is done on a plane benchstone. The wide roller assures stabilityand preserves the surface of the stone.The tappet screw allows honing to asecond (micro-) bevel without havingto reclamp the blade. Set, honing guideand angle jig.

Blade width max. 60 mmBlade thickness max. 15 mmNo. 707168 46.13 € 54.90 €

B VERITAS® SHARPENING SYSTEM IIA high-precision gauge for precise andconsistent perpendicular sharpening ofall straight-edged blades. Also suitablefor short, irregular and tapered Japaneseblades. Aluminium body, easy-glidingbrass roller. Quickly adjustable gaugewith grip. Instructions included.Thickness max.13 mmWidth 6-72 mmBevel angle 15°-54°Counter chamfer (10°-20°)No. 703666 49.58 € 59.00 €

C VERITAS® SMALL BLADE HOLDERThis mount enables easier sharpeningof short blades such as spokeshaves,reversing blades or small violin planes.Two magnets and a moveable fence holdthe blades securely, the die-cast alumi-nium grip extends the blade and enablesa controlled sharpening, either by handor with the Veritas sharpening system(No. 707168).102 x 38 x 10 mmNo. 702110 14.71 € 17.50 €

G STANLEY® SHARPENING GUIDE SETWith plastic rollers and a folding anglegauge, indluding sharpening stone andoil.Max. blade width 65 mmMax. blade thickness 9 mmGrit 120 / 240No. 707166 20.08 € 23.90 €

D UNIVERSAL HONING GUIDEThe wide roller preserves the surface ofthe stone and prevents tilting. Can beused as an angle jig with grinding machines which have a tool rest. Aluminium body with brass roller.Width 40 mmMax. blade width 65 mmMax. blade thickness 10 mmNo. 707149 11.68 € 13.90 €

E DOUBLE JAW HONING JIGThe blade is centrally held in one of thetwo grooves in the vise-like aluminiumjaws.Roller width 26 mmOpening 82 mmMax. blade thickness 7 mmNo. 711400 12.18 € 14.50 €

F ANGLE GAUGEFOR TOOL EDGESFor checking bevel angles.Brass coated.12 angles (15°-120°)Ø 46 mmNo. 707261 3.11 € 3.70 €

I TOGERU® KNIFE SHARPENINGDEVICEFor keeping the correct angle whensharpening knives manually. Simplyput on the back of the blade – whensharpening, position the incorporatedceramic fence on the honing stone sur-face. That way the bevel angle is heldfast and warping movements are avoided.Suitable for double-bevelled knives.Blade width 30-50 mmBlade thickness max. 3 mmNo. 705377 8.32 € 9.90 €

J DMT®-SHARPENING SYSTEM,FINE/EXTRA-FINESharpening knives and tools can be soeasy – especially with this SharpeningSystem from DMT. The easy transportableDiafold Magna-Guide Sharpening Systemfeatures an Aligner Blade Guide (ABG)which provides 7-angle adjustability forthe right edge every time – from big outdoor knives to fine kitchen knives. It works in conjunction with the MagneticAngle Guide (MAG) to keep the blade atthe ideal angle for sharpening. The deepclamp design securely holds blades up to9.5 millimeters in thickness while sharp-ening, without scratching the blade.

Included in delivery are: DMT AlignerClamp, Magnetic Angle Guide, Diafoldsharpener with fine and extra-fine grits.No. 705428 46.97 € 55.90 €

Angle jigHoning jig

A

B

C

G

D

E

F

IJ

1 Basic setThanks to the wide flat rest with ad-justable angle, this system is suitable forscrapers and parting tools as well as chis-els and planers. Includes a left and rightbase with eccentric locking mechanism,arm and flat rest.Platform 126 x 76 mmNo. 702170 74.96 € 89.20 €

2 Vari grindThis jig, which can be rotated in any di-rection is designed for sharpening turn-ing and profile gouges. The angle can beaccurately adjusted using the hole ma-trix. Notches on the back indicate the setangle.Max. Intake Ø 19 mmNo. 702171 44.54 € 53.00 €

H

1

2

Powerful and bounce-free

95

Japanese hammers and mallets | 96

Picard® | 98

Estwing® | 98

Soft-face hammers and rawhide hammers | 99

Veneer hammers | 99

Accessories | 99

Nails and rivets | 99

Punch awls and drivers | 100

Wrecking bars | 100

HAMMERSNAILS

PRY BARS

Hammers, nails, pry bars || Japanese hammers and mallets

96

Japanese hammers and mallets

The simple outward appearance of theJapanese hammer conceals its inner sophistication. The hammer head is softin the middle and hardened only at theends. This allows the full force of a blowto be transferred while simultaneouslydampening vibrations and reducing thehammer's 'bounce'. One face of the hammer is flat while the other is groundwith a slight crown, making it especiallyuseful for driving nails flush with a surface and for marquetry work. The Genno's high efficiency means youcan generally select a lighter weight incomparison to conventional Europeancarpenter’s hammers. The handles aremade of sturdy, wear-resistant JapaneseKashi wood (white oak) and are extralong and ergonomically designed forcomfortable use. Replacement handlesare available upon request. The specifiedweights refer to the weight of the headalone.

A DAMASCUS STEEL HAMMERA triumph of Japanese blacksmithing:This attractive damas-cus steel hammer proves that a highlysophisticated imple-ment can be producedfrom mankind´s oldesttool, despite its archaic appearance.The polished layers of Yellow Paper Steeland the softer centre made of 25-layerdamascus steel produce a delightful colour-contrast. Befitting its high quality,this model is equipped with an extra-longhandle made of ebony. The master´s signature is engraved on the head.Head weight 375 gOverall length 360 mmNo. 705692 419.33 € 499.00 €

B SQUARE HAMMER, ENGRAVEDAn attractive tool and a beautiful gift:Those who are fond of attention to detailwill certainly appreciate Master Sato’shand-engraved Genno. To highlight themythological animal motifs engraved onboth sides of the hammer head, the surface is copper-patinated.Head weight 375 gOverall length 340 mmNo. 714203 64.71 € 77.00 €

C OCTAGONAL HEAD HAMMER Octagonal-headedhammer with flatcheeks, ideal for adjusting and fittingwork. The cheeks can also be used as striking surfaces.Overall length 300-360 mmHead weight115 g No. 714001 19.24 € 22.90 € 225 g No. 714002 20.92 € 24.90 € 375 g No. 714003 24.29 € 28.90 € 570 g No. 714004 30.17 € 35.90 € 750 g No. 714005 38.57 € 45.90 €

D SQUARE HAMMERAll-purpose hammerwith particularlygood directional stability, ideal for assembly work, driving nails etc. A 375 gGenno is suitable for striking Japanesechisels. Square-headed, rounded edges.Overall length 300-360 mmHead weight115 g No. 714101 19.24 € 22.90 € 225 g No. 714102 21.09 € 25.10 € 375 g No. 714103 24.87 € 29.60 € 570 g No. 714104 31.68 € 37.70 € 750 g No. 714105 36.64 € 43.60 €

E NOMI GENNOEasy-to-handle hammer for driving Japanese chisels and carving tools.Round head with large striking areamakes mishits unlikely.Head weight 375 gOverall length 240 mmNo. 714011 20.08 € 23.90 €

F CARPENTER’S HAMMERPuristic, well-balanced carpenter’s hammer with slightly bell-shaped headand round cross-section. The flanks arebronzed, the faces are finely ground.Head weight 375 gOverall length 335 mmNo. 714010 18.40 € 21.90 €

G GENNO HATTORIJapanese-style hammer for driving chisels and nails. Round head with oneflat and one rounded striking face, selectively hardened.Head weight 375 gOverall length 300 mmNo. 700975 10.00 € 11.90 €

A

H FUNATE GENNOThe bell-shaped head increases directional stability during use and thetapered end allows high-precision work.Drop-forged head, copper-plated, with aslightly crowned face.Overall length 360 mmHead weight170 g No. 714110 25.13 € 29.90 € 300 g No. 714112 28.07 € 33.40 €

I JAPANESE CARPENTER’S HAMMER

No. 714120 19.92 € 23.70 €

Hammering tips:

When driving a nail into a piece ofwood, friction causes an incredibleamount of heat to be produced. Thisheat destroys the wood’s fibres andtends to loosen the nail’s ultimate gripon the wood. It is therefore best to usethe shortest, thinnest appropriate nailand to tap it in up tothe neck using softblows and then seatit with one sharp tap.

The flat face of the Genno should beused to tap the nail and the curvedface to seat it.

In hardwood, we recomm-end pre-drilling and/or snipping off the tips of thenails to allow them to severthe wood’s fibres as theyare driven into the wood.

The head of the hammershould be aimed directly at the nail axis.

For weight-bearing pieces,nails should be hammeredin at an angle.

B C D

E F G H I

This is the perfect tool for driving nails.The conical head stays true, does notbounce and the sharp nail claw is exceptionally efficient at removing nails. The faces and cheeks are designed toallow use in tight spaces. Extra-longhandle.Head weight 400 gOverall length 390 mm

Hammers, nails, pry bars || Japanese hammers and mallets

97

For practically effortless hammering witha high driving force and perfect balance.The heads are forged by hand, and theharmoniously proportioned head and ergonomic handle yield a wonderfully organic tool which you simply will notwant to put down. The asymmetrical construction allows maximum directionalstability during use.Overall length 210 or 310 mm respectively.Head weight1 290 g No. 714322 52.02 € 61.90 € 2 600 g No. 714323 58.74 € 69.90 €

B CORNER HAMMER

No. 714007 27.65 € 32.90 €

C BLACKSMITHING HAMMERS From a Japanese master workshop:The archaic appearance of the Japaneseblacksmith hammer reveals little aboutits inner qualities. In relation to itsweight, the strongly asymmetrical face,which tapers from a square cross-sectionto the round strike surface, provides forhigh impact force as well as rebound-freeand fatigue-free working. Partially harde-ned and delicately balanced togetherwith the ergonomically formed shaft, it supports the impact rhythm during forging work. Replacement handles areavailable.Overall length 300-330 mmHead weight1 750 g No. 714016 72.94 € 86.80 € 2 1350 g No. 714017 87.98 € 104.70 €

Replacement handles are available at www.more-than-tools.de

D JAPANESE SQUARE MALLET

No. 714052 20.92 € 24.90 €

E MINI HAMMERS, 6 PIECE SETFor craftsmanship:

No. 714036 81.26 € 96.70 €

F MINI ANVILWith a rounded and a flat horn. Ideal forjewellery work. Forged steel, polishedand chrome-plated, mounted on a solidiron base, standard quality finish.Length 130 mmWeight approx. 550 gNo. 700153 11.68 € 13.90 €

G BLACKSMITH`S ANVILThis easy-to-transport anvil, cut from a railway track, is suitable for small to medium-sized blacksmithing works. Facemilled flat and chamfered on two sides.Surface area 120 x 100 mmHeight 115 mmFace 100 x 60 mmWeight 3400 gNo. 706566 39.92 € 47.50 €

A 1 2 B C 1 2

D

E

F

G

Unusual Japanese hammer with two triangular faces, ideal for driving nails ininaccessible spots, for example insidethe corners of furniture bodies. Thishammer will not be in continual use, but when it is used it will be worth itsweight in gold!Head weight 185 gOverall length 300 mm

The mini hammers from Japanese masterblacksmiths are ideal for delicate work.Thanks to their drop-shaped handles,they are well-balanced and lie superblyin the hand. The forged heads made ofcarbon-steel are differentially hardenedand facilitate delicate and rebound-freestrikes. Handles made of natural hickory.6-part set.Head weight approx. 70 gOverall length 215 mm

A JAPANESE HAMMER (KOZUCHI)Maximum efficiency:

For assembly work in cabinetmaking and carpentry. The mallet consists of awaxed Japanese red oak head with a white oak handle. Head 140 x 90 x 90 mm.Head weight approx. 820 gOverall length 330 mm

Hammers, nails, pry bars || Picard®, Estwing®

98

Picard®

A PICARD® ROOFING HAMMER 698The classic carpenter’s tool:

No. 705685 32.61 € 38.80 €

No. 705686 57.56 € 68.50 €

C PICARD® BLACKSMITH’S HAMMER

Head weight1000 g No. 705334 27.06 € 32.20 € 1500 g No. 705335 33.53 € 39.90 €

D PICARD® WARRINGTON HAMMER

Estwing®

No. 705698 53.36 € 63.50 €

No. 705691 69.66 € 82.90 €

No. 705697 50.34 € 59.90 €

I ESTWING® ROOFING HAMMER

No. 705699 55.38 € 65.90 €

A B C D

E

F

G

H

I

Picard hammers have been manufactured in Germany for over 150years. With innovation and experience,the company develops products of exep-tional quality.

Unbreakable, oval steel tube handle witha vibration-absorbing dampening, non-slipelastomer grip. The head features a differentially hardened point and claw,checkered face and magnetic nail slotswhich can also accommodate small nails.Head weight 600 gOverall length 315 mm

B PICARD® ROOFING HAMMER 790The head and neck are forged from one piece and bonded seamlessly to the leather grip, making this Picard hammeralmost indestructible. The handle is madeof disk-stacked leather and screwed tothe full-length tang through a head plate.If necessary, it can be tightened usingthe screw at the butt end. Thanks to theuntreated leather, the handle absorbsdamp and adjusts to the individual shapeof the hand. Smooth face, selectivelyhardened and fully polished head withmagnetic nail slot.Head weight 700 gOverall length 315 mm

Drop-forged hammer with traditionalScandinavian shape: elliptical eye, conically tapered hammer face with fer-ruled edges and rounded fin. Ash handlewith annular wedge.Overall length 360 mm

All-purpose hammer with classic headshape for assembly and inlay work. The fin is rounded, the face slightly convex in order to prevent indentations. Ash handle.Overall length 300 / 320 mmHead Ø 20 / 25 mmHead weight180 g No. 705682 16.72 € 19.90 € 300 g No. 705683 19.83 € 23.60 €

The head, neck and leather handle ofthis hammer are joined seamlessly tomake a practically indestructible strikingtool. The full-length tangs and, heads areforged from one piece. The heads are differentially hardened and, together withthe neck, fully polished.The handle ismade of disk-stacked varnished leatherand riveted at the end.

E ESTWING® LOCKSMITH`S HAMMERHighly versatile – for use in metalworking,as well as assembly and fitting work, driving nails into wood, and much more.

F ESTWING® CLAW HAMMERWith their round, smooth, bell-shapedhead with slightly curved face and thecurved nail claw, claw hammers are idealfor driving in and loosening nails whileprotecting the surface.Head weight 560 gOverall length 315 mm

G ESTWING® ALL-PURPOSE HATCHETRobust axe, ideal for professional carpen-try tasks as well as trekking. Thin bladewith hammer head and nail claw. Can be suspended from a belt using the leather blade protector.Total weight approx. 900 gOverall length 325 mmBlade length 90 mm

H ESTWING® ROCK PICKA rock pick is a combination of a ham-mer and a pick, used by geologists. Thelong, hardened, pointed tip allows stonesto be struck with extreme accuracy, andthus split with precision.Head weight 390 gOverall length 320 mm

The point can be driven into the wood,and is thus used for moving beams andkeeping the hammer on the roof. Withmagnetic nail claw and smooth face.Head weight 600 gOverall length 330 mm

Head weight 300 gOverall length 300 mmNo. 705695 41.93 € 49.90 €

Hammers, nails, pry bars || Soft-face hammers and rawhide hammers, Veneer hammers, Accessories

99

Soft-face hammers and rawhide hammers

Soft-face hammers

A WHITE RUBBER HAMMER

B WIHA® SOFT-FACE MALLET

Rawhide hammers

D RAWHIDE HAMMER

No. 705681 83.19 € 99.00 €

CA

B Veneer hammers

Hammer veneering is a proven techniquefor making and restoring veneers. Thepre-steamed and ironed veneer is presseddown using the warmed veneer hammer.Working from the middle of the pieceoutwards, the hammer is moved backand forth across the piece to force outbubbles and excess glue. The roundedface distributes pressure efficiently andevenly.

E VENEER HAMMER

No. 705688 35.21 € 41.90 €

Accessories

Nails and rivets

F JAPANESE PRECISION WOOD NAILSFor decorative corner, T or L joints whichare exposed to high mechanical loads,conical wooden nails are the first choice.After pre-drilling with an appropriate conical drill, the nails are applied with agentle hammer strike and a little glue.Also ideal for restoring furniture, musicalinstruments, historical fitted features orto fill small imperfections. Made of long-fibred, tough melawis wood.Diameter Length Packing3.5 / 1.8 mm 35 mm 20 pieces No. 717280 2.77 € 3.30 €

300 pieces No. 717310 33.53 € 39.90 €45 mm 20 pieces No. 717281 2.77 € 3.30 €

300 pieces No. 717311 33.53 € 39.90 €4.7 / 2.2 mm 45 mm 20 pieces No. 717282 2.77 € 3.30 €



90 pieces No. 717315 33.53 € 39.90 €

G TAPERED DRILL BITFor drilling holes for conical woodennails and screws. Made of HSS. Length 75 mm. Hexagonal shaft.Diameter3 mm No. 717284 7.98 € 9.50 € 3 mm: ideal wooden nails 717281 and 7173114 mm No. 717285 8.82 € 10.50 € 5 mm No. 717286 10.00 € 11.90 € 6 mm No. 717287 12.52 € 14.90 €

H SHAKER NAILSManufactured using traditional methods:These decorative copper nails are beatenin the USA on original machines datingfrom the 19th century. They are used torivet the frames of shaker jars, for delicate craftsmanship work, model construction, leather applications or forornamental purposes.

I BRASS RIVETSFor the widest variety of materials, inparticular for the assembly of knife gripplates, for joining thin components madeof wood, metal, plastic or leather, or for decorative purposes. If necessary, theycan be cropped, and the heads can berounded off. They are driven with a ham-mer (if necessary, with dimpling punch).1 pack = 50 capsules and 50 bolts.

* maximum thickness of the materialswhich are to be joined togetherShaft diameter 4 mm.

6 mm 11mm No. 830150 6.30 € 7.50 €6 mm 15 mm No. 830151 7.31 € 8.70 €8.5 mm 25 mm No. 830152 10.00 € 11.90 €

E

D

F G H I

To stop marks being left. The advantagethese hammers (with heads made ofwhite rubber) have over their black counterparts is that they do not leave unattractive marks on light-coloured surfaces. Slightly convex head, solid red beech shaft in conical socket.Overall length 305 / 340 mmHead Ø 54 / 61 mmWeight370 g No. 705679 12.52 € 14.90 € 670 g No. 705680 15.55 € 18.50 €

This hammer is used for assembly workand fitting parts together. The yellow faceis medium hard and made of colourfastand wear-resistant polyurethane. Soft materials can be hammered withoutleaving pitting using the blue face, whichis made of soft, colourfast and wear-resistant elastomer. The durable housingis made from malleable cast iron. A comfortable-to-hold hickory handlecompletes this great product.Overall length 290 / 325 mmHead Ø 30 / 40 mmWeight300 g No. 717865 13.36 € 15.90 € 640 g No. 717869 16.72 € 19.90 €

C RAWHIDE HAMMERS, LEAD COREAmerican buffalo hidecoiled around a lead core dampens the blowand simultaneously protects the surfaces of sensitive pieces fromdamage. Ideal for furni-ture assembly, interior,restoration, parquetryand tiling work. The rawhide heads arehighly resistant to wear and can also beused for striking chisels and carvingtools. Hickory handles.Overall length 230 / 290 mmHead Ø 32 / 45 mmWeight260 g No. 714327 22.10 € 26.30 € 450 g No. 714328 27.56 € 32.80 €

Elegant, solid-steel model for small-scalework. Polished brass face for low frictionand good heat transfer. Chisel-shapedbutt end for disassembly work. Slip-resistant, soft plastic grip.Total weight 475 gOverall length 355 mmFin width 85 mm

This rawhide hammer is a specialisedtool used with a splitting knife to splitwooden shingles. The head of the hammer is made from the hide of water buffalo, which is rolled and compressedthree times. Then the hammer head hasto rest for months. It is very tough and shock-absorbent. As the head is made of rawhide, it has alarge diameter and is very effective but atthe same time lightweight. The handle is made of lacquered ash.Total weight 1250 gOverall length 360 mmHead Ø 89 mm

Length Pieces5 mm 400 No. 830142 7.14 € 8.50 €8 mm 300 No. 830143 8.82 € 10.50 €

Ø head thickness*

Hammers, nails, pry bars || Accessories, Wrecking bars

100

Punch awls and drivers

A NAIL STARTERTool for making pilot holes to start longnails. Forged, hardened steel blade witha hilted tang. Red oak handle, ferruledon both sides.Blade length approx. 150 mmOverall length 290 mmNo. 717200 28.40 € 33.80 €

B PUNCH AWL Hardened stainless-steel point, also for marking. White oak handle.

Blade length 55 mmOverall length 105 mmNo. 717205 7.14 € 8.50 €


C PUNCH AWL, REAMING AWL WIHA®

This tool features a semi-gloss lacqueredhandle made of beech which looks goodand is comfortable to hold. The through-hardened blade is nickel-plated.Overall length 190 mm

D JAPANESE DRIVER SET, 4-PARTTo drive nails, pins, splints etc. Chrome-plated surface, octagonal shaft. 4-part set.Working length 50 mmOverall length 150 mmØ 3/4/5/6 mmNo. 710797 9.16 € 10.90 €

A B C D1 2

Wrecking bars

E WRECKING BARSReliable wrecking bar made of fully hardened spring steel and therefore particularly light. The wide, precision-ground pry tips at both ends allow thebar to be easily wedged without damaging the surface of the piece. 10-year warranty.

JAPANESE NAIL PULLERCompact, highly efficient tools forpulling nails and disassembling components. The expertly crafted claws and smoothlycurved faces prevent the workpiece frombecoming marred during disassembly.The flat face on the back of the claw canbe used to drive the claw under a nail oras a hammer. Made of finely polisheddrop-forged steel with case-hardenedworking surfaces.

F WRECKING BARS

No. 714308 23.53 € 28.00 €

G NAIL PULLER

No. 714314 21.85 € 26.00 €

L PICARD® NAIL PULLER

No. 705665 25.13 € 29.90 €

I PRECISION MOULDING BARS

Pry tip 49 mmOverall length 300 mm375 gNo. 714309 14.20 € 16.90 €



J NAIL PULLER, EXTRA THIN

No. 714307 12.86 € 15.30 €

K PRECISION NAIL PULLER, S-TYPE

No. 714310 13.87 € 16.50 €

E

F

G

I

J

K

L

H STAINLESS STEEL NAIL PULLER

No. 714342 36.89 € 43.90 €

H

1 PUNCH AWL This punch awl is used for pre-punchingholes and drill holes in wood.No. 717859 4.62 € 5.50 €

2 REAMING AWLA reamer is used for enlarging holes anddrill holes in wood to facilitate screwingoperations.No. 717858 4.62 € 5.50 €

Length 900 mmMax. nail shaft Ø 13 mm2400 gNo. 705978 63.87 € 76.00 €





For heavy-duty use. Pry bar (without slit) 35 mm.Overall length 450 mmMax. nail shaft Ø 6 mm850 g

For cabinetmaking and carpentry. Double-sided claw.Overall length 360 mmMax. nail shaft Ø 5 / 6 mm690 g

Robust drop-forged tool with a head for nails with a maximum diameter of 2.5 mm. Beech handle with hoop and ferrule.Overall length 230 mmMax. nail shaft Ø 6 mm

The precision-ground claw is wide andthin, allowing pieces to be gently easedapart without damaging their surfaces.Max. nail shaft Ø 2 / 2.5 mm.

Lightweight iron withouthammer head. Extra-thinpry bar, 27 mm.Overall length 200 mmMax. nail shaft Ø 2 / 2 mm80 g

For furniture and fine work.Overall length 160 mmMax. nail shaft Ø 2 / 2.5 mm90 g

Made from stainless steel suited for out-door use. Slightly smaller forged claw on long side for easier insertion of the nailhead. Partially polished.Overall length 360 mmMax. nail shaft Ø 5 / 6 mm560 g

101

Turning tools | 103

Combination tools | 105

Tool sets | 106

Lathes and accessories | 107

Chucks | 109

Occupational safety, measuring tools | 110

Woodturningtools

Let’s take turns!

Woodturning tools

102

WOODTURNING - A HANDICRAFTOF LONG-STANDING TRADITIONNEWLY INTERPRETED

NEW

Sharpening pass


Sharpening service



Workshops:

Turning – A Two Day Basic Class

Turning – A Two Day Advanced Class

Turning Green Wood

Can Variations

Beyond the Lathe

Pen Turning

Turning Hollow Vessels

Turning in Majorca

For more information see

www.more-than-tools.de/workshops

BASICALLY, THERE ARE TWO DISTINCT METHODS OF TURNING WOODSpindle turning and faceplate turning.

SPINDLE TURNING

Here, the wood fibres run parallel to the

spindle axis. You clamp the workpiece either

with a spur driver and the revolving centre

or with a chuck, which, in the case of long

workpieces, can also be supported by the

revolving centre.

Examples: chair legs, newels, tool handles,

vases, tumblers...

Tools: Roughing-out gouges, spindle gouges,

chisels, parting tools, hook tools, ring tools

and hollowers.

Roughing-out gouges

A roughing-out gouge is usually required to

make edged workpieces round or to remove

bulk material.

Spindle gouges

The spindle gouge is an all-purpose tool for

cutting profiles, recesses, fillets, V slots and

curvatures, which can also give you a high

surface quality.

Chisels

For smoothing straight, curved, hollow and

slightly profiled surfaces and for cutting

narrow profiles and notches.

Parting tools

As the name implies, parting tools are

used for cutting off (parting) finished work.

Primary uses also include working on or

backcutting end grain in spindle turning,

and cutting grooves.

Hook tools

The hook is a versatile tool for hollowing

out workpieces. Thanks to the complex blade

geometry, it is equally suitable for bulk wood

removal and finishing end grain.

Ring tool

Like the hook, the ring tool is used for

cutting end grain on tumblers and vases.

If used correctly, you can achieve fine

surfaces with it.

Hollowers

Most hollowers are cranked and thus suitable

for hollowing end grain in vessels with narrow

openings.

FACEPLATE TURNING

The wood fibres run perpendicular to the

spindle axis, which means you have to work

on cross-grain twice per revolution. Work-

pieces that are turned across the grain can

be clamped in chucks, on faceplates or screw

chucks. They are rarely supported by the

tailstock because it would be obstructive

and the mostly short pieces do not require

support. With heavy workpieces, however,

tailstock support is recommended at the

beginning.

Examples: bowls, boxes, plates...

Tools: bowl gouges and scrapers.

Tools for faceplate turning are somewhat

more solid than tools for spindle turning to

accommodate the forces during cutting.

Bowl gouge

Used in a similar way to the spindle gouge,

you can use the bowl gouge to work on the

inside and outside of bowls and hollow work-

pieces.

Scrapers

Scrapers are preferred for finishing surfaces

because they allow the best surface quality.

But this is not their only use – they are also

suitable for creating profile edges.

Some faceplate turning tools can also be

used for spindle turning and vice versa. How-

ever, this should be left to the experienced

turner because it requires mastering the cor-

rect techniques. Some tools are only suitable

for one purpose.

QUALITY REQUIREMENTS Decisive for pleasure in turning is the quality

of the blades. The steels must be heat-resis-

tant in order to prevent the softening of the

cutting edges. The HSS steels, which com-

prise most of our blades, are stable and ex-

tremely wear-resistant up to 570°C. Still

harder and more abrasion-resistant is PM

steel, manufactured by powder metallurgical

methods. The vesilience behaviour is also

very important: Strong handles of dense wood

dampen vibrations and contribute to better

results.

SHARPENING AND MAINTENANCEBecause of the hard steels, we recommend

bulk material removal on a normal bench

grinder using a sharpening jig, e.g. Tormek®

BGM 100 or Wolverine Sharpening System.

For honing, you can use the Tormek® Wet

Grinder, multiform stones, and for quick

intermediate sharpening our products from

DMT.

Woodturning tools || Turning tools

103

Turning tools

Crown®-turning tools

The tools forged by the Sheffield-based Crown Works are excellently designed and expertly crafted. Theblades are made of carefully tempe-red, extremely durable M2 HSS steel.They are polished and fitted in ergo-nomically designed rosewood handleswith heavy-duty brass ferrules.All specified dimensions are approximate.

Crown®-PRO-PM-Eisen

The ultimate turning tools: PRO-PMgouges are the top of the line for exotic hardwoods, laminates or woodwith mineral inclusions. The very highpercentage of cobalt (8%) and tung-sten (10.5%) make them highlydurable. The tools hold their edge atleast five times longer than HSS tools.All PRO-PM tools come fitted with ashhandles.

We extend a 5-year warranty to all ourcrown turning tools!

Spindle gouges

CROWN® »ENGLISHSPINDLE GOUGES«Flat-milled from roundmaterial, fine, slightlyrounded bevel.Blade width / Overall length

6 / 400 mm No. 701905 18.40 € 21.90 € 10 / 400 mm No. 701906 20.34 € 24.20 € 13 / 400 mm No. 701907 25.46 € 30.30 € Die Forged Gouge19 / 400 mm No. 701908 31.51 € 37.50 € PRO-PM10 / 495 mm No. 701972 35.80 € 42.60 € 13 / 495 mm No. 701973 41.09 € 48.90 €

CROWN® »GERMAN-STYLE SPINDLEGOUGES«The standard gougesfor spindle work. The die-forged flutesrun the entire length of the blades. Fin-ger-shaped bevels.Blade width / Overall length

6 / 380 mm No. 701936 32.77 € 39.00 €8 / 380 mm No. 701937 35.21 € 41.90 €

13 / 380 mm No. 701938 36.97 € 44.00 €19 / 380 mm No. 701939 42.61 € 50.70 €25 / 380 mm No. 701940 58.74 € 69.90 €32 / 520 mm No. 701941 68.82 € 81.90 €

CROWN® HEAVY-DUTY ROUGHINGOUT GOUGESFor removing largeamounts of stock du-ring preliminary roun-ding. Die-forged, deep fluted blades withstraight bevels.Blade width / Overall length19 / 380 mm No. 701901 35.29 € 42.00 € 32 / 530 mm No. 701902 47.65 € 56.70 € PRO-PM19 / 485 mm No. 701954 75.55 € 89.90 €

Bowl gouges

CROWN® HEAVY-DUTYBOWL GOUGESPrimarily for large-scalefacework. Made ofround stock with milled,deep flutes. Straight bevel.Blade width / Overall length6 / 610 mm No. 701909 28.49 € 33.90 € 10 / 610 mm No. 701910 34.37 € 40.90 € 13 / 610 mm No. 701911 42.77 € 50.90 € »Superflute«19 / 660 mm No. 701912 73.87 € 87.90 € PRO-PM10 / 665 mm No. 701975 54.54 € 64.90 € 13 / 665 mm No. 701976 70.50 € 83.90 €

CROWN® »ELLSWORTH« GOUGESDesigned by MasterWoodturner David Ells-worth, these versatilebowl gouges are for rough and finish shap-ing of the inside and outside of hollowforms. Special elliptical grind. Hardwoodhandle, instructions included.Blade width / Overall length13 / 690 mm No. 701961 72.94 € 86.80 € PRO-PM13 / 665 mm No. 701955 94.87 € 112.90 €

Chisels

CROWN® SKEWCHISELSStandard tools forsmoothing both flatand curved surfaces. Skew edged,double-bevelled blades.Blade width / Overall length13 / 380 mm No. 701914 23.45 € 27.90 € 19 / 380 mm No. 701915 29.33 € 34.90 € 25 / 380 mm No. 701916 37.39 € 44.50 € PRO-PM19 / 485 mm No. 701977 43.61 € 51.90 €

CROWN® OVALSKEW CHISELSFor spindle turning andfacework. Speciallydesigned to reduce friction between theblade and tool rest to allow them to be eas-ier to guide than chisels made of rectan-gular stock. Skew edged, double-bevelled.Blade width / Overall length19 / 380 mm No. 701917 27.65 € 32.90 €25 / 380 mm No. 701918 32.69 € 38.90 €

CROWN® ROUNDEDSKEW CHISEL WITHROUNDED EDGEThe rounded supportedge facilitates finer movements and pre-vents the cutting edge from becomingembedded. High Speed Steel.Blade width / Overall length19 / 380 mm No. 701987 35.21 € 41.90 €

CROWN® SQUARECHISELFor finishing flat andconvex surfaces. Pri-marily for facework.Double bevel.Double bevel.Blade width / Overall length13 / 380 mm No. 701919 22.61 € 26.90 €

Parting tools

CROWN® STANDARDTRIANGULARPARTING TOOLSDouble bevel.Blade width / Overall length3 / 365 mm No. 701926 25.13 € 29.90 €6 / 380mm No. 701927 25.13 € 29.90 €

CROWN®

FLUTEDPARTING TOOLSingle bevelled,German-style.Blade width / Overall length6,5 / 400 mm No. 701929 34.87 € 41.50 €

CROWN® DIAMONDPARTING TOOLDouble-bevelled,taper-ground,English-style.Blade width / Overall length5 / 400 mm No. 701928 32.35 € 38.50 €

CROWN® KNIFE-SHAPED PARTING TOOLThin, very rigid blade for making finegrooves and parting cuts.Height 30 mmBlade width / Overall length1,6 / 210 mm No. 701965 22.61 € 26.90 €

Scrapers

CROWN® ROUNDNOSE SCRAPERFor finishing thesurfaces of curvedobjects. Primarily usedfor spindle turning.Blade width / Overall length13 / 380 mm No. 701922 20.92 € 24.90 € 19 / 380 mm No. 701923 25.97 € 30.90 €

CROWN® MULTI-TIPSCRAPERVersatile tools forfinishing the innerand outer surfacesof any shape.With 3 exchangeable, taper-groundHSS cutters:round, pear-shaped and square.Blade width / Overall length27 / 380 mm No. 701943 61.26 € 72.90 €

CROWN® SIDE CUTTING SCRAPER,ROUNDFor finishingthe bottoms andinner surfaces of hol-low forms and for undercutting.Blade width / Overall length19 / 380 mm No. 701930 29.33 € 34.90 €

CROWN® BOWL FINISHINGSCRAPER, ROUNDHeavy-duty scraperfor finishing theinside of largehollow forms.Blade width / Overall length25 / 550 mm No. 701960 48.66 € 57.90 €

CROWN®

HOOK NOSESCRAPERAlso suitable for finishing undercuts.Blade width / Overall length25 / 500 mm No. 701986 38.57 € 45.90 €

CROWN® DOVETAILSCRAPERFor cutting the recessto accommodate thejaws of a dovetailchuck.Blade width / Overall length13 / 340 mm No. 701985 25.97 € 30.90 €

Round No. 701945 14.71 € 17.50 €Drop No. 701946 16.72 € 19.90 €Square No. 701944 14.20 € 16.90 €

Forged / Milled gouges

Compared with milled gouges, forgedturning gouges have a denser struc-ture and are thus more resistant towear. In the past, this difference wasmuch more serious, resulting in twogouge variants. Today, the preferenceis to forge the larger gouges to reducematerial waste.


104

Side hollowers scrapers

B CROWN® HOLLOWING TOOLCompact tool forhollowing boxes,bowls, vases etc.45° curvedBlade width / Overall length6 / 320 mm No. 701967 27.65 € 32.90 €

A CROWN® BEAVER DEEP HOLLOWINGTOOLSpecial tool for deephollow forms. The ad-justable depth stop al-lows clean andaccurate cuts to be made safely evenwhen your view is restricted by the piece.Instructions included.Blade width / Overall length1 Straight13 / 645 mm No. 701947 102.44 €121.90 €2 GooseneckFor sides and undercuts.13 / 615 mm No. 701948 111.68 € 132.90 €Replacement tip, for both models

No. 701949 34.37 € 40.90 €

C SWAN-NECK HOLLOWING TOOLFor turning hollowvessels. The ex-changeable tip andthe semicircularprofile cross-section of the shaft makeit extremely versatile. The finger-shapedcutter is used for the cutting process;the shaft lies with the flat side on thehand rest. For fine-finish scraping oneuses the supplied disc cutter; to optimisethe angle of pressure theround side of the shaft lieson the tool rest.Ø 20 mmOverall length 580 mmNo. 702001 44.45 € 52.90 €Replacement cutter, finger-shapedNo. 702002 6.13 € 7.30 €Replacement cutter, roundNo. 702003 6.13 € 7.30 €

A

Hook and ring tools

E CROWN® RING TOOLIdeal tool for hollowinginto end grain on thin-walled wet-wood ob-jects such as cups andvases. Thin dual-bevel HSS ring, design-ed for light-duty use.Blade width / Overall length12 / 400 mm No. 701931 32.69 € 38.90 €

D STUBAI® HSS RING TURNING TOOLSRobust ring tools withchangeable cutters forrough and fine cuttingwork on bowls and hol-low vessels. The holdercan be fitted with changeable toolsmade by Wiedemann (socket Ø 8 mm).The cutting ring can be used fromboth sides.Overall length 600 mmØ internal / Ø external12 / 18 mm No. 702005 114.20 € 135.90 €Repl. blade No. 702007 77.23 € 91.90 €20 / 26 mm No. 702006 142.77 € 169.90 €Repl. blade No. 702008 104.12 € 123.90 €

F HOOK TURNING TOOLFor turning deep andwide hollow forms.The tool is suitable forsoft and medium-hardwood or green wood.Heat-resistant, very tough HSS steel(65 HRC), forged, beech handle witha copper ferrule.Hook Ø approx. 10 mmShaft Ø 12 mmOverall length 510 mmHandle length 260 mmNo. 701999 82.18 € 97.80 €

As a rule, deep turning hooks areused to cut from inside to outside(illustration taken from the book

»Das Drechslerwerk« No. 713575,which is available at our webshopunder www.more-than-tools.de).

1

2

C

DVD – GRÜNHOLZ DRECHSELNIn this film the Scot-tish master wood tur-ner Michael O´Donnellshows step by stephow small works ofart can be created ona turning lathe usingfreshly felled (green)wood. In six extra-ordinary projects,O’Donnell demonstra-tes how vessels canbe made from end-grain and cross-grainwood with wafer thin, translucent walls,some with natural edges.DVD, 80 min. in German.No. 713861 25.04 € 29.80 €

Japanese emery cloth for fine sanding see chapter finishing.

D

F

Ornamental-forming and special tools

G CROWN® CHATTER TOOLTo create decorativewave patterns on end-grain Woodturningparts (bowls, jewellery,jar lids, etc). The thintongue oscillates uponcontact with the rota-ting part, and this gen-erates regular chattermarks. Incl. change-able straight and rounded tongues. Instruction manual. Beech wood handle.Width 10 mmOverall length 300 mmNo. 701154 44.45 € 52.90 €Replacement lip, straight No. 701155 5.80 € 6.90 €Replacement lip, roundedNo. 701156 5.80 € 6.90 €

K CROWN® BEAD FORMING TOOLFor cuttingaccurate beadsand pre-shapingrings.6 bzw. 10 mmBlade width / Overall length

6 / 380 mm No. 701933 24.29 € 28.90 €10 / 380 mm No. 701934 25.13 € 29.90 €

L CROWN® CAPTIVE RING TOOLFor producing looserings and rings thatare captured by theworkpiece, double-bevelled blades.Blade width / Overall length

6 / 380 mm No. 701962 27.65 € 32.90 €10 / 380 mm No. 701963 28.49 € 33.90 €

H CROWN® THREAD CHASER SETFor cutting internal andexternal threads,e.g. for makingthreaded boxes.Hardened tool steel,rosewood handles.Instructions included. »Hint: Try out first –only practise leads tosuccess!«Each set consists ofone inside and oneoutside thread chaser.gradient = toothing/inchOverall length235 mmGradient12 Inch No. 701956 60.42 € 71.90 € 18 Inch No. 701958 61.26 € 72.90 €

I CROWN® CHINESEBALL TOOL SETChallenge for professional turners:Special set of tools forturning up to 5 nested ballaccording to the model ofthe Chinese ball. The 6-piece set consists of abead forming tool, toolmount and four ball-cuttingknives. Instruction bro-chure included. For fre-quent use we recommendfitting each of the ball-cut-ting knives with its owntool mount.6-piece set.Overall length approx. 300 mmNo. 701981 115.04 € 136.90 €Replacement tool mountNo. 701982 29.08 € 34.60 €

J CHINESE BALLA piece of woodturning wizardry in itsfinished form. Three nested ball made ofcedro wood.Exterior Ø 60 mmNo. 831012 27.31 € 32.50 €

IHG

J

B

E

K

L


105

Combination tools

Kelton™The company Kelton from New Zealand(home of high-quality turning tools) isthe most innovative company on the mar-ket for turning tools. Many different famous turners and carvers have someinfluence on these products and thuskeep on improving the tools. Since usinghigh-quality materials and sturdy designyou will enjoy these tools for a long time.

A KELTON™ NEGATIVE RAKESCRAPERThe Kelton™ Negative Rake Scraperis a universal tool that can be used inmany different ways to achieve optimumresults. It allows quick removal of bulkmaterial as well as delicate finishing.The unique swivelling head assembly,combined with the negative rake setting,allows almost any tool position forworking on both the inside and outsideof workpieces, as well as making it easyto scrape across the grain in hollowprojects. The three milled flats on themain shaft prevent the tool fromrotating so that it can be used safelyeven with an angled tool tip.Overall length 270 mmShaft diameter 16 mmBlade width 23.5 mmNo. 702093 92.35 € 109.90 €

B KELTON™ HOOK TOOLHook tools have a long tradition when itcomes to turning.This tool has aclever thought-outgeometry in orderto ensure the safeturning of bowlsand other moulds.Besides it is possi-ble to adjust theangle of the hookso it suits the per-sonal liking. Theblade, made out ofHSS steel, is hardened in a specialmethod and hence has – compared to conventional hooks – an extra longlifetime. No matter whether you haveto remove larger chippings or a smoothsurface is needed, this is the perfecttool for dry as well as for green wood hol-lowing. Designed by Kel Mc Naughton.Shaft Diameter 16 mmOverall length 335 mmNo. 702076 73.11 € 87.00 €

C KELTON™ HOLLOWERS,3-PIECE SETThe Kelton hollow-ers have been de-signed to work theinsides of vesselswith narrow open-ings. Thanks totheir special geo-metry, they do not only help expertsbut also beginners with quick removalof wood as well as fine smootheningand are, at the same time easy tosharpen. Made out of HSS steel theyhave a long lifetime. Three differenthead shapes for different vessel shapeswill enable perfect results.

Hollowers 13 mmOverall length 340 mmShaft diameter 13 mmNo. 702073 77.31 € 92.00 €



D KELTON™ STANDARD HANDLES These tools do not slip in the handsthrough a special plastic wrapping aroundthe handle. Two simple headless screwsallow an easy exchange of the insets andsafely clamp them. Since the handleshave two ends it is possible to clamp a13mm as well as a 16mm shank. Themetal core has enough counter-balancefor the insets and prevents vibrations byits large mass. The surface is bronzed. It is possible to fix an additional torquearrestor handle in the crosswise threadedholes at each end in order to gain bettercontrol. Designed by Kel Mc Naughton.Diameter 32 mm

1 Standard handle KH 2Overall length 255 mmNo. 702072 43.70 € 52.00 €

2 Standard handle KH 3Overall length 410 mmNo. 702077 45.38 € 54.00 €

3 Torque arrestorgandle KH 2 / KH 3A torque arrestor handle which can be used as additional support with the Kelton Standard Handles.Overall length 140 mmNo. 702078 20.92 € 24.90 €

B

C

D

E KELTON™ ULTIMATE HANDLE ER 25Delivered with two collets for shaftdiameters 13 and 16 mm.If necessary the last 10 cmof the handle can be filledwith lead granules to make the handle heavier and minimize vibrations.Overall length 425 mmNo. 702084 100.00 € 119.00 €

G KELTON™ ULTIMATE HANDLE ER 32Delivered with twocollets for shaft dia-meters 16 and19 mm. Set containsa main handle anda extension. Overall length 445 + 150 mmNo. 702085 142.02 € 169.00 €

H KELTON™ ULTIMATE HANDLE ER 16This handle can also be used as anextension for the ER 25. Deliveredwith two collets for shaft diameters8 and 10 mm.Overall length 275 mmNo. 702086 79.83 € 95.00 €

F KELTON™ TORQUE ARRESTORHANDLE ER 25A torque arrestor handle which can beused as additional support with theKelton Ultimate Handles, ER 25/32.Overall length 140 mmNo. 702087 20.92 € 24.90 €

I KELTON™ MC NAUGHTON SYSTEMMake two out of one:

Shaft diameter 25.4 mm (1 Inch)No. 702071 284.87 € 339.00 €

Shaft diameter 30 mmNo. 702089 284.87 € 339.00 €

No. 702095 175.63 € 209.00 €

A

E G

F

H

1

23

I

J

With this remark-able tool, you areable to save themiddle part of abowl in one pieceand therefore pro-duce several bowlsout of one woodenblock. Especiallywith scarce piecesof wood that haveunique grain it ispossible to opti-mally make use ofthe wood and meanwhile save time. Thetool post has to be inserted into the banjo,it will than not only serve as a guide for thebowl saver but also as a tool support forhollowers by a separate support yoke. The solid design allows working without vibrations on big bowls and is thus user-friendly. The set includes a tool post,comprising 4 parts, a standard handle(KH 3) with a slip resistant plastic wrapping and a set of blades (4 pieces).The K3 handle can also be used withKelton hollowers. By using a specialhardening process the blades are highlywear resistant and have therefore a long lifetime. Designed by Kel Mc Naughton.

Handle length 410 mmBlade width 25 mmMax. diameter of the savedbowl 355 mm

J KELTON™ LARGE BOWL BLADES,3-PIECE SETThese large bowl blades can be used withthe Kelton™ McNaughton System Standard and are suitable for largebowls, plates and similar objects.Blade width 30 mmMax. diameter of the saved bowl 457 mm

No. 702010 142.02 € 169.00 €No. 702011 63.03 € 75.00 €


106

Tool sets

Crown® turning tool sets

A STANDARD SET, 8-PIECERoughing out gouge, 19 mm, No. 701901; 2 English spindle gouges, 6 mm and 12 mm, No. 701905 and No. 701907; German style spindlegouge, 19 mm, No.701939; skew chisel,12 mm, No. 701914; oval skew chisel,25 mm, No. 701918; side cuttingscraper (round), 19 mm, No.701930; diamond parting tool, 5 mm, No. 701928. Comes in wooden case.No. 701994 251.26 € 299.00 €

B MINIATURE SET, 5-PIECE2 English spindle gouges, 3 mm and 6 mm, No. 701903 and No. 701904;skew chisel, 6 mm, No. 701913; roundnose scraper, 6 mm, No. 701921; part-ing tool, milled on both sides, 1.5 mm,No. 701925. In wooden case.Overall length approx. 260 mmHandle length 160 mmNo. 701952 96.64 € 115.00 €

C SPECIAL PEN TURNING SET, 3-PIECEHSS tools to make writing equipment.Gouge 6 mm; oval skew chisel 13 mm;parting tool 3 mm. Handles made of rosewood.Overall length 230 mmHandle length 140 mmNo. 701988 65.46 € 77.90 €

D PRO-PM TURNING TOOL SET,5-PIECEMade of ultra-hard sintered steel, thesetools hold their edges 5 times longer.Roughing out gouge, forged, 19 mm;heavy-duty bowl gouge, 10 mm; shortbowl gouge, 10 mm; diamond partingtool, 5 mm; skew chisel, 19 mm.In wooden case.Overall length approx. 490 mmHandle length 320 mmNo. 701980 297.48 € 354.00 €

Taylor® turning tool setsThese well-designed turning tools comefrom the distinguished Henry Taylorforge, founded in 1834 in the Englishcity of Sheffield. They are characterisedby particularly high-quality craftsman-ship, the fine bevel of the inner surfacesfacilitates smooth working surfaces withlow cutting forces. Made of HSS steelwith a long edge life.

E MICRO-HOLLOWING TOOL SET, 3-PIECEFor processing smaller workpieces withundercut and bowls. Straight scraper toolfor rough material removal when hollow-ing out, two angled scraper tools for thefine processing of the hollow shape andthe hard-to-reach areas behind the neck.Overall length 280 mmHandle length 175 mm

F HSS TURNING TOOL SET, 5-PIECERoughing out gouge, 19 mm; bowl gouge,9 mm; parting tool, 3 mm; round nosescraper, 19 mm; oval skew chisel, 19 mm.Overall length 410 mmHandle length 240 mmParting tool: Overall length 290 mmHandle length 175 mm

Hattori® Turning Tool Sets, HSSCost-effective, robust turning tools madeof heat-resistant HSS steel (63 HRC)with 3-year quality guarantee. Ergonomi-cally formed hardwood handles, finelypolished surfaces, ‘de-sharpened’ edges,and generously-proportioned brass hoops.Each set is supplied in a wooden case.The listed specifications are approximate.

I MINI SET, 5-PIECEFor small scale spindle and faceplate turning.Spindle gouges, 3 mm and 6 mm;round scraper, 6 mm; skew scraper, 6 mm;standard parting tool, triangular, 2 x 6 mm.Overall length 260 mmHandle length 155 mmNo. 701853 37.73 € 44.90 €

J MIDI SET, 8-PIECEVersatile set of compact gouges forspindle turning and small scale faceplateturning. Roughing out gouge, 16 mm;2 spindle gouges, 10 mm, curved andflat; oval chisel, 13 mm;scraper, 13 mm; round scraper, 13 mm;standard parting tool, triangular, 4 x 13mm; diamond parting tool, 4 mm.Overall length 290 mmHandle length 195 mmNo. 701851 83.95 € 99.90 €

H MAXI SET, 6-PIECEThe basic assortment of tools for spindleand faceplate turning. Heavy-duty rough-ing out gouge, 19 mm; spindle gouges,10 mm and 13 mm; oval chisel, 25 mm;round nose scraper, 19 mm; diamondparting tool, width 5 mm.Overall length 470 mmHandle length 300 mmNo. 701850 134.37 € 159.90 €

G LEATHER TOOL ROLL FOR TURNINGTOOLSThis tool roll made of dark-brown calfleather protects your tools from dirt anddamage. The handles are inserted in thesewed-on straps.Outside dimensions 610 x 370 mmMax. tool length 550 mmNo. 717509 58.74 € 69.90 €

A

B C

D

E

F

G

H I

J

Woodturning tools || Lathes and accessories

107

B HAGER® HDE 49 LATHEThe universal lathe for virtually any pur-pose. 3 speed levels guarantee maximumtorque, while the heavy, torsion-resistantbase frame with U-shaped transverse

No. 705553 2809.24 € 3343.00 €

Lathes and accessories

With over 35 years of experience in theproduction of turning lathes, the Germancompany Hager has become one of theleading manufacturers. Hager offerstailored special solutions in the fieldof turning, and stands for high-quality,functionally well thought out products.The turning lathes are produced inaccordance with DIN standards, and the long-term supply of spare parts andaccessories is guaranteed. All accessoriesare compatible with all models.

A HAGER® STAR LATHEInnovative short lathe with direct drivefor turning beginners. 2 speeds, adjusta-ble via safety switch without changingthe belt. Continuously adjustable electro-nic speed control with gentle ramp up/down. The sturdy base frame absorbs vibrations and guarantees smoothworking. The pivotable spindle stockallows you to turn large bowls while standing directly in front of the work-piece. The tool rest and tailstock are easily secured using a keyless eccentricclamp. Exact spindle alignment, high repeat accuracy.

Specifications:Height of centre over bed 200 mm, distancebetween centres 640 mm, speed range 300-2500 rpm, hollow spindle Ø 15 mm (#2 MTinner cone) with M33 x 3.5 DIN 800 threadand four bearings, tailstock with #2 MT quill(100 mm travel) and measuring scale, three-phase motor 0.75 kW (1 HP), motor rating230 V, working height/axis centre 1130 mm,length 1300 mm, width 550 mm, height1300 mm, 117 kg.

No. 705550 1764.71 € 2100.00 €

Hager®

BA

Standard equipment:Tool rest base and tailstock with eccentric clamp, tool rest 250 mm,#2 MT four-tooth spur driver withjacknut Ø 24 mm, #2 MT revolvingcentre, prepared for external turningequipment, knockout rod, operating instructions.

traverse ensures maximum stability andvibration-free working. Continuously adjustable electronic speed control with gentle ramp up/down. The pivotablespindle stock allows you to turn largebowls while standing directly in front ofthe workpiece. The tool rest and tailstockare easily secured using a keyless eccentric clamp. Exact spindlealignment, high repeat accuracy.

Specifications:Height of centre over bed 225 mm, distancebetween centres 1000 mm, speed ranges150-450 / 400-1200 / 950-2900 rpm, hollowspindle Ø 20 mm (#3 MT inner cone) withM33 x 3.5 DIN 800 thread and four bearings,

Oneway®

C ONEWAY® 1224 LATHEHigh-quality compact lathe with baseframe and small footprint.The continuously variable 2-step speedcontroller can be fixed in two positions.It comes programmed ready for use withbuilt-in ramp up/down. The heavy, tor-sion-resistant base cabinet with a low-mounted motor for reduced vibrationscan also be used for storage. The offsettubular bed construction guarantees al-most perfect torsional rigidity and meansthat chips fall through cleanly. The pa-tented clamping mechanism makes iteasy to lock the tool rest and tailstockinto position without a key. Unparalleledsmoothness and repeat accuracy.

Specifications:Height of centre over bed 159 mm, distancebetween centres 609 mm, speed ranges 150-2000 / 150-4000 rpm,

No. 705551 2016.81 € 2400.00 €

Fitted with the latest technology, thesehigh-precision lathes manufactured inCanada guarantee a long life and are apleasure to use. The innovative designcombines the benefits of cast materialsand the advantages of stable welded-steel constructions.

tailstock with #2 MT quill (100 mm travel)and measuring scale, three-phase motor 1.5 KW (2 HP), motor rating 230 V, workingheight/axis centre 1110 mm, length 1670mm, width 520 mm, 135 kg.

Standard equipment:Tool rest base and tailstock with eccentric clamp, tool rest 300 mm,#3 MT four-tooth spur driver withoutjacknut Ø 24 mm, #2 MT revolvingcentre, prepared for external turningequipment, knockout rod, operating instructions.

D ONEWAY® 2436 LATHEHeavy professional lathe with externalturning option for all your needs.3 speed levels, programmed for gentleramp up/down, can be continuously adjusted on the pivotable controls. The vertically adjustable base frame with torsion-resistant bed is very heavy andoptimally absorbs vibrations. On the out-board spindle you can work smoothly onbowls of almost unlimited diameter. Thepatented clamping mechanism makes iteasy to lock the tool rest and tailstockinto position without a key. Unparalleledsmoothness and repeat accuracy.

Specifications:Height of centre over bed 305 mm, distancebetween centres 914 mm, speed ranges 20-800 / 190-1900 / 305-3050 rpm, hollowspindle Ø 5/8 inch (15.8 mm) with 400 mmlong hole (#2 MT inner cone) with M33 x 3.5

1.5 KW (2 PS)No. 705552 4917.65 € 5852.00 € 2.25 KW (3 PS)No. 705549 5171.43 € 6154.00 €

DIN 800 thread and three bearings, tailstockwith #3 MT quill (100 mm travel) and measu-ring scale. Three-phase motor, motor rating 220 V, working height/axis centreadjustable from 1092 – 1219 mmin 25 mm steps, length 1524 mm, width 787 mm, 385 kg.

Standard equipment:Cast iron tool rest with patentedclamping mechanism, cast iron tailstock,steel faceplate Ø 152 mm, tool rest fromglobular cast iron 355 mm,#3 MT live centre system,#2 MT »Safe Driver«, knockout rod,48-position indexing, operating instructions.

hollow spindle Ø 7/16 inch (11.1 mm)(#2 MT inner cone) with 1"–8tpi RH threadand three bearings, tailstock with #2 MT quill(80 mm travel) and measuring scale, three-phase motor 0.75 KW (1 HP), motor rating220 V, working height/axis centre 1130 mm,length 1194 mm, width 597 mm, 136 kg.

Standard equipment:Cast iron tool rest with patented clamp-ing mechanism, cast iron tailstock, steelfaceplate Ø 76 mm, tool rest from globu-lar cast iron 280 mm, #2 MT live centresystem, #2 MT »Safe Driver«, knockoutrod, 24-position indexing, operating instructions.

C D

When buying a lathe you receive a voucher over 150 € for any turning workshop at DICK.

All lathes excluding shipping costs.

Woodturning tools || Lathes and accessories

108

A ONEWAY® SPUR DRIVER WITHOUTJACKNUT, #2 MTFor use on lathes with hollow spindlesto clamp workpieces for spindle turning.Ø 25.4 mmNo. 702123 39.41 € 46.90 €

B ONEWAY® LIVE CENTRE SYSTEM

Morse taper#2 MT No. 702137 99.08 € 117.90 € #3 MT No. 702138 99.08 € 117.90 €

C HAGER® SPUR DRIVER WITH JACKNUTIndispensable clamping aid for spindle turning.

Ø mm15 mm No. 705572 65.13 € 77.50 € 20 mm No. 705573 65.13 € 77.50 € 24 mm No. 705574 65.13 € 77.50 €

Spur driver with jacknut #3 MTØ mm20 mm No. 705575 72.18 € 85.90 € 24 mm No. 705576 72.18 € 85.90 € 30 mm No. 705577 72.18 € 85.90 €

D HAGER® REVOLVING CENTREOne bearing, the whole head rotates.Shaft Ø 20 mmMorse taper#2 MT No. 705546 73.03 € 86.90 € #3 MT No. 705547 82.27 € 97.90 €

E HAGER® SUPPORT RINGStabilises long workpieces in combination with revolving centre.Inside Ø 20 mmNo. 705548 10.92 € 13.00 €

F HAGER® ADAPTERAllows #2 MT lathe accessories to be used in #3 MT collets.No. 705541 10.00 € 11.90 €

G HAGER® SELF-TIGHTENINGDRILL CHUCKPrecise chuck for fast and easy high-force clamping without key.Clamping range 3-16 mmMorse taper#2 MT No. 705543 69.66 € 82.90 € #3 MT No. 705544 69.66 € 82.90 €

A

I HAGER® ADJUSTABLE CURVEDTOOL RESTTool rest with 90° curve.Features convenient length adjustmentwith an Allen-head screw. Ideal for hollowing.Approx. 230 x 110 mmNo. 705545 67.98 € 80.90 €

G

J KELTON™ HOLLOWING GATEA clever and sta-ble tool rest thatfits into everybanjo. Both multi-tip scrapers andhollowers can beguided on this ro-table support. The rotation of the yokeenables you to start the cut in an arch.This circumstance eliminates sidewaysforces and gives you better control overyour tool. If working on deep bowls andvessels it is possible to extend the arminto the workpiece. The surface is bronzed.The tool is delivered with three jokes for13, 16, 19 mm shaft diameter.Designed by Kel Mc Naughton.Height 175 mmArm length 210 mmShaft diameter 25.4 mm (1 Inch)No. 702070 98.32 € 117.00 €Shaft diameter 30 mmNo. 702088 98.32 € 117.00 €

J

1 Kelton™ carvers jig baseThis base willguide the clampunit of the carversjig and enables tofix it to the Wood-turning lathe andwork bench. Con-taining a baseplate, two handles, a carriage boltand two washer plates. The surfaceis bronzed.Base plate 240 x 75 mmNo. 702079 87.39 € 104.00 €

2 Kelton™ carvers jig clamp unitThis clamp unit canalso be clamped intoparallel vices andbench vices withoutusing the carvers jigbase. The ball guidingallows a fixation at al-most any angle whilethe hex shank can befixed in different posi-tions in the vice.Using it in combina-tion with the carvers jig base this clamp-ing element will be an adequate chuck.Set contains ball guiding, t-handle aswell as a 100mm face plate and a carver´s srew. The surface is bronzed.Overall length 280 mmNo. 702080 188.24 € 224.00 €

K

2

4 Kelton™ faceplates

Ø mm38 mm No. 702081 41.18 € 49.00 € 64 mm No. 702082 49.58 € 59.00 €

3 Kelton™ lathe spindle replicatorWith this spindle replicator it is possibleto fix chucks to the vice.Thread: M33 x DIN 800Overall length 125 mmNo. 702083 46.97 € 55.90 €

4

3

H HAGER® CLAMPING ARBOR CHUCKIdeal for clamping workpieces with naturaledges which cannot be clamped in normal chucks. After drilling a Ø 30 mmcore hole into the workpiece and pushingthe workpiece onto the clamping arbor,the eccentric knurled disk anchors theworkpiece in the bore hole.Thread, M33 DIN 800Arbor length 43 mmØ 30 mmNo. 705542 53.70 € 63.90 €

I

H

B

C

D

E

F

Spur driver with jacknut #2 MT

Faceplate for workpieces with little clamping surface. The surface is bronzed.Overall length 80 mm

1

This system is based on a two-bearinglive centre with a cutting ring and athreaded shaft onto which you can fit dif-ferent attachments including self-madeones. Comes with a cone that can beused on both the inside and outside ofturnings, as well as a large point andknockout rod.Cone diameter 90 mmPoint diameter 45 mm

K KELTON™ CARVERS JIGThe possibility to lock workpieces in different positions does appeal to turn-ers, carvers, sculptors and other wood-workers alike. The sturdy and versatilemechanism can be installed on the bedof lathes as well as on work benches,while different clamping devices can beused. Whether you have a turned objectthat you do not want to take out of thechuck or – as a carver – want to use dif-ferent sized faceplates, this tool offerssolutions for many clamping problems.Designed by Kel Mc Naughton.

K

Woodturning tools || Chucks

109

Chucks

B ONEWAY® STRONGHOLD The advantage of this self centering 4 jaw chuck lies in it`s heavy design. Suitable for large objects, this chuck of-fers security in almost all clamping situa-tions. It is easy to handle single-handedwith the help of the included chuck key.This way you can use your other hand toposition the workpiece. The body, manu-factured out of one piece, is low vibratingand rotates accurately. A nickel coatingprotects the chuck from rust. The casehardened jaw slides, made from chrome-nickel-steel, are extremely wear resistant No. 702158 249.50 € 296.90 €

C TOWER JAWS, PREMIUM PROFILEDSERRATED, STRONGHOLD Tower jaws will excel when it comesdown to turning long pieces without tail-stock support. It is possible to fix work-pieces by clamping or spreading them.The serration on the inside of the jawssafely fixes the workpiece. The shape ofthe inner jaws is not completely roundbut angled. This patented design enablesthe jaws to safely clamp square stockand minimises the damage of the sur-face. The jaws also have more contactpoints than conventional serrated jawswhen clamping round stock. This enablesa higher clamping force.

StrongholdSize 2Ex. ch.* 51-85 mm / In. ch.* 70-108 mmNo. 702130 50.84 € 60.50 €Size 3Ex. ch.* 92-127 mm / In. ch.* 111-149 mmNo. 702132 55.88 € 66.50 €

D SPIGOT JAWS, PREMIUM PROFILEDSERRATED, STRONGHOLDFor clamping smaller pieces thesespigot jaws are the right choice. It ispossible to fix workpieces by clampingor spreading them. The serration on theinside of the jaws safely fixes the work-piece. The shape of the inner jaws isnot completely round but angled. Thispatented design enables the jawsto safely clamp square stock and minimi-zes the damage of the surface. The jawsalso have more contact points thanconventional serrated jaws when clamp-ing round stock. This enables a higherclamping force.

StrongholdEx. ch.* 12-66 mm / In. ch.* 28-66 mmNo. 702121 40.25 € 47.90 €

F DOVETAIL JAWS, STRONGHOLDThe outside and inside surface of thejaws is smooth and not serrated. This en-ables you to gently clamp round work-pieces. Only low clamping force can bepracticed due to the non-serrated insidesurface.

StrongholdSize 2Ex. ch.* 51-89 mm / In. ch.* 66-114 mmNo. 702124 36.05 € 42.90 €Size 3Ex. ch.* 92-127 mm / In. ch.* 111-152 mmNo. 702126 41.09 € 48.90 €Size 4Ex. ch.* 108-136 mm / In. ch.* 127-165 mmNo. 702128 49.50 € 58.90 €

B

C D F

E PREMIUM PROFILED SERRATEDJAWS, STRONGHOLDSerrated jaws are used during all stan-dard clamping situations. It is possibleto fix workpieces by clamping or sprea-ding them. The serration on the insideof the jaws safely fixes the workpiece.The shape of the inner jaws is notcompletely round but angled. Thispatented design enables the jawsto safely clamp square stock and minimi-zes the damage of the surface. The jawsalso have more contact points thanconventional serrated jaws when clam-ping round stock. This enables a higherclamping force.

StrongholdSize 3Ex. ch.* 98-133 mm / In. ch.* 114-152 mmNo. 702125 46.64 € 55.50 €Size 4Ex. ch.* 114-146 mm / In. ch.* 124-165 mmNo. 702127 48.66 € 57.90 €

A ONEWAY® TALONThe Oneway Talon chuck is a self center-ing 4 jaw chuck. Suitable for almost allturning needs, this is the standard chuckfor the turner. It is easy to handle single-handed with the help of the includedchuck key. This way you can use yourother hand to position the workpiece. The body, manufactured out of onepiece, is low vibrating and rotates accurately. A nickel coating protects thechuck from rust. The case hardened jawslides, made from chrome-nickel-steel,are extremely wear resistant and runsmoothly and exactly in the toothed guid-ing. Recommended for Woodturninglathes with a swing up to 200 mm. The set contains a taper lock adaptor,

and run smoothly and exactly in the toothedguiding. Recommended for Woodturninglathes with a swing from 200 mm on.The set contains a taper lock adaptor,premium profiled jaw` s size 2, chuckkey, woodworm screw, Allen key. Different taper lock adaptors are available upon request.Diameter 105 mmWeight approx. 3.6 kgM33 x DIN 800Jaws # 2: external chucking 44 - 82 mm /internal chucking 60 - 101 mm

premium profiled jaw’s size 2, chuck key,woodworm screw, Allen key. Differenttaper lock adaptors are available upon request.Diameter 85 mmWeight approx. 2 kgJaws # 2: external chucking 41 - 37 mm /internal chucking 51 - 90 mm.

M33-AdapterM33 x DIN 800No. 702159 195.71 € 232.90 €

1 Inch-Adapter1 - 8 (Inch)No. 702160 195.71 € 232.90 €

A

TalonSize 2Ex. ch.* 12-66 mm / In. ch.* 51-85 mmNo. 702149 44.96 € 53.50 €Size 3Ex. ch.* 85-114 mm / In. ch.* 98-130 mmNo. 702151 50.84 € 60.50 €

TalonEx. ch.* 9-41 mm / In. ch.* 25-60 mmNo. 702142 33.53 € 39.90 €

TalonSize 3Ex. ch.* 73-101 mm / In. ch.* 85-117 mmNo. 702146 41.09 € 48.90 €

TalonSize 2Ex. ch.* 41-73 mm / In. ch.* 51-90 mmNo. 702145 30.08 € 35.80 €Size 3Ex. ch.* 66-95 mm / In. ch.* 85-120 mmNo. 702147 37.73 € 44.90 €

E

Oneway® woodturning-chucksAll chucks of the trademark Oneway areproduced in Canada to guarantee highquality and accuracy. For both chucksTalon / Stronghold many accessories are

available, from which you can chose according to your needs. The body` s aremanufactured in one continuous opera-tion in order to guarantee the highest-possible true running-accuracy.

Ex. ch.* = External chuckingIn. ch.* = Internal chucking

Woodturning tools || Chucks, Occuputional safety, measuring tools

110

A SPIGOT JAWS,DOVETAIL PROFILEFor clamping smaller pieces these spigotjaws are the right choice. It is possible tofix workpieces by clamping or spreadingthem. The outside and inside surfaceof the jaws is smooth and not serrated.This enables you to gently clamp roundworkpieces. Only low clamping forcecan be practiced due to the non-serratedinside surface.

StrongholdEx. ch.* 9-50 mm / In. ch.* 25-66 mmNo. 702122 40.25 € 47.90 €

A

2

C

B FACEPLATE SEGMENTSThese segments make it possible toclamp complex shapes in order to finishthem, e.g. pieces without stub. No mat-ter, whether you have to work round, ovalor angled pieces, the movable rubbernobs keep hold of each workpiece. Theclamping force is limited due to the con-struction of the jaws. In order to achievelarger dimensions of the segments theyhave been produced out of aluminium.This way the centrifugal forces are mini-mized compared to steel segments.

1 Stronghold, Size 1Ex. ch.* 76-216 mm / In. ch.* 127-257 mmNo. 702133 77.23 € 91.90 €



C FLAT JAWS FOR INDIVIDUAL CLAMP-ING SITUATIONS, STRONGHOLDWooden blocks are screwed to the face ofthe jaws which are then turned. This wayyou are able to make your own customgrip jaw set.

StrongholdNo. 702136 34.37 € 40.90 €

B

TalonEx. ch.* 6-44 mm / In. ch.* 27-63 mmNo. 702143 33.53 € 39.90 €

TalonNo. 702154 34.37 € 40.90 €

Talon, Size 1Ex. ch.* 51-200 mm / In. ch.* 101-251 mmNo. 702152 77.23 € 91.90 €

Talon, Size 2Ex. ch.* 73-273 mm / In. ch.* 124-298 mmNo. 702153 82.77 € 98.50 €

3

1

Occupational safety, measuring tools

F KELTON™ CALLIPERDue to its protrudingshape, this tool al-lows you to measurethe wall and basethickness of evennarrow vessels withmore accurate re-sults than traditionaldouble-ended callipers.450 x 220 mmNo. 702094 58.74 € 69.90 €

E OUTSIDE CALLIPERS

No. 707203 39.92 € 47.50 €

H DIVIDERS

No. 707201 24.29 € 28.90 €

D STARRET® CALLIPERSSolid callipers made from alloyed toolsteel with smoothed sides and edges. The opening can be tensioned at the jointwith an adjustable screw that does notshift during use.

1 Starret® outside callipersFor checking material thickness.Leg length 300 mmMax. opening 400 mmNo. 707348 60.42 € 71.90 €

2 Starret® inside callipersFor checking openings and insides ofhollow objects.Leg length 300 mmMax. opening 400 mmNo. 707349 48.66 € 57.90 €

G CENTRE FINDER FOR ROUND STOCKMakes work fabulously easy:Simply place it on the end of a roundpiece of wood and mark two lines - thepoint of their intersection is the exactcentre.Length 130 mmMaximum Ø of workpiece 220 mmNo. 707262 6.13 € 7.30 €

J PELTOR™ OPTIME 1 HEARINGPROTECTORThis all-round hearing protector frommarket leader Peltor™ provides the bestimaginable protection despite being com-fortably light. The slim profile of themuffs still provides a generous insidedepth and, combined with the two-pointattachment, ensures the best possiblecomfort even during extended use.Attenuation rating SNR (Single NumberRating) 27 dB.Recommended noise rating 87-98 dB.No. 707551 14.71 € 17.50 €

K -WOODTURNER'S JACKETLightweight turner's jacket made of cottonblended fabric. Velcro fasteners on sleevesand collar, collar can be secured when notin use, 2 back pockets, zip.

SizeM No. 701887 50.34 € 59.90 € L No. 701888 50.34 € 59.90 € XL No. 701889 50.34 € 59.90 €

K

F

G

E H

D

1

2

I J

An overview table with chucking capacity of the single jaws can be foundonline at www.more-than-tools.de

Robust outside callipers with hinge andquarter-circle division with set screw.Satin-finish carbon-steel.Side length 190 mmMax. opening 250 mm

Robust hinge dividers with quarter-circledivision and set screw. Satin-finish carbon-steel.Side length 190 mmMax. opening 245 mm

I SAFETY GOGGLESModern, lightweight double-lenssafety goggles with flexible, non-slipsports sidepieces for comfort.Soft nose pads that can be removedfor cleaning ensure optimum fit.100% UV protection, scratch-resistant.No. 707552 9.16 € 10.90 €

Ex. ch.* = External chuckingIn. ch.* = Internal chucking

Hand-cut rasps | 112

Machine-cut rasps | 114

Dreadnought rasps, plane- and sawrasps | 115

Files for metal working | 116

Glardon/Vallorbe®-files | 116

Diamond files | 118

Files for knife makers | 118

Files for wood-based materials | 119

Handles and accessories | 120

111

Handmade quality!

Rasps and files || Hand-cut rasps

112

Cut by masters, cherished by experts:Until the early 20th century, the teeth ofrasps were cut exclusively by hand (usinga special pointed punch and hammer)into the body of the rasp before it washardened. Because of the slightly varyingdepths and distances of the individualteeth, the work face is slightly inhomoge-neous in texture. This leads to asmoother cutting performance on fibrousmaterial such as wood (no »chattering«).For this reason, professionals still preferhand-cut rasps even today.

Herdim® Precision RaspsHerdim® rasps are hand-cut rasps whichare manufactured in countless workstepsby the »last of their craft«. The smooth-ing and shaping of the blank, cutting ofthe teeth, meticulous hardening, anneal-ing and trueing are typical manufacturingsteps of the handmade rasp. Up to10,000 teeth, each one raised individu-ally with a hammer and special pointedpunch, ensure smooth results without be-coming clogged. Made of hardened car-bon-steel, the rasps are highly durable.The tangs are annealed.

A FLAT RASPS (WITH HANDLE TANG)Cut Cross section Cross length3 25x4 mm 200 mm No. 704505 28.49 € 33.90 € 4 25x4 mm 200 mm No. 704506 31.26 € 37.20 € 5 25x4 mm 200 mm No. 704507 35.88 € 42.70 €

B FLAT RASPSCut Cross section Cross length

1 5 10x4 mm 125 mm No. 704502 20.67 € 24.60 € 2 5 16x4 mm 150 mm No. 704704 25.38 € 30.20 € 3 5 20x5 mm 200 mm No. 704707 35.21 € 41.90 €

Herdim »Ultra« over 10,000 teeth10 20x5 mm 200 mm No. 704709 87.98 € 104.70 €

A 1 2 3

RASPS

Our Herdim® and Schwertfisch® rasps as well as our Superhard file

rasps are indispensable tools for cabinet-makers, conservators and

instrument makers.The effective surface of the rasp consists of

individual teeth, and the density and size of the teeth varies. This

results in more or less coarse surfaces which can then be further

treated. As also with files, the fineness of the rasp is described in

terms of the grade of cut, from 3 for coarse to 10 for extremely fine.

A new development on the market are Microplane rasps and Japa-

nese saw rasps, which conquer more and more areas of use. Rasps

are used for working hardwood and softwood, leather, plastics,

plaster, marble and soft metals.

FILES

Files are used with wood following rasping to smooth the surface,

as well as for precise shaping. Their real domain is, however, metal

working. Thus, the Glardon/Vallorbe® files, manufactured in Vallorbe

and making up the greatest part of our range of files, were originally

manufactured for the requirements of the Swiss watch industry.

Their quality standards have made Glardon/Vallorbe® the world’s

leading maker of precision files, with no alternatives in terms of

sharpness and cutting edge life.

Hand-cut rasps

Hammering the teeth

B

Blade ShoulderTang

GroundCut length

Rasps and files || Hand-cut rasps

113

A

A CABINET RASPSCut Cross section Cross length3 24x5 mm 200 mm No. 704720 33.11 € 39.40 € 4 24x5 mm 200 mm No. 704721 36.89 € 43.90 € 4 30x7 mm 250 mm No. 704727 61.18 € 72.80 € 5 20x4 mm 150 mm No. 704716 32.27 € 38.40 € 5 24x5 mm 200 mm No. 704722 38.99 € 46.40 €

Herdim »Ultra« over 10,000 teeth10 24x5 mm 200 mm No. 704724 87.98 € 104.70 €

B HALF-ROUND RASPSCut Cross section Cross length5 16x5 mm 150 mm No. 704732 28.40 € 33.80 € 5 20x5 mm 200 mm No. 704733 33.78 € 40.20 €

C HALF-ROUND RASP, SLIMCut Cross section Cross length5 10x3 mm 150 mm No. 704741 25.97 € 30.90 €

D CROSSING RASPCut Cross section Cross length5 18x5 mm 150 mm No. 704551 31.01 € 36.90 €

B C D

E RIFFLER SET, 8-PIECECrafted and hardened with great care bymaster craftspeople. For shaping convexand concave surfaces. The teeth are cuton both sides, the ends bent in oppositedirections. Square mid-section. Comes ina leather roll. Overall length 185 mm,cut length 55 mm, cut 4: equaling,warding, trapezoid, square, three-square,half-round, crossing, round.No. 704599 167.14 € 198.90 €

Schwertfisch® RaspsOur portfolio of Schwertfisch® rasps,which are also traditionally cut by handin small workshops, is unique throughoutEurope. Due to their special shape, theycan be used universally and offer goodvalue for money. The arched arrangementof the teeth makes these rasps incrediblyeffective and provides smooth results.Blades made of C45 carbon-steel.

F G H

F CABINET RASP SPECIALExtra long, very thin cabinet rasp with a fine cut.Cut Cross section Cross length4 30 x 4 mm 350 mm No. 704679 6.39 € 7.60 €

G FLAT RASP (WITH HANDLE TANG)Cut Cross section Cross length3 24 x 4 mm 200 mm No. 704571 5.29 € 6.30 €

H FLAT RASPS (WITH POINTED TANG)Cut Cross section Cross length4/6 25 x 4 mm 210 mm No. 704671 7.48 € 8.90 € 7 10 x 3 mm 120 mm No. 704670 4.12 € 4.90 €

I J K L

I CABINET RASPSCut Cross section Cross length3 25x5 mm 200 mm No. 704572 5.29 € 6.30 € 4 25x5 mm 210 mm No. 704672 7.48 € 8.90 €

J CROSSING RASPSCut Cross section Cross length5 15x3.5 mm 130 mm No. 704674 4.12 € 4.90 € 5 25x4.5 mm 200 mm No. 704675 7.48 € 8.90 € 7 10x3.5 mm 100 mm No. 704673 3.70 € 4.40 €

K ROUND RASPSCut Cross section Cross length2 8 mm 240 mm No. 704678 6.39 € 7.60 € 3 6 mm 160 mm No. 704574 5.29 € 6.30 €

L HALF-ROUND RASPSCut Cross section Cross length6 15x4 mm 130 mm No. 704677 4.12 € 4.90 € 7 8x2.5 mm 100 mm No. 704676 3.70 € 4.40 €

E

Rasps and files || Hand-cut rasps, Machine-cut rasps

114

E MINI RIFFLER SET, 5-PIECEFor model-making, making musical in-struments etc. Overall length 140-180 mmhead length 20-50 mm, cut 4No. 704681 12.10 € 14.40 €

F SHAPING HEAD SET, 5-PIECEWith a coarse rasp hand-cut, for woodand plastic. 5 pieces.Head Ø approx. 16 mmNo. 704690 7.48 € 8.90 €

G F.D. HOOF RASP FILELarge rasp which can be used on bothsides: extra coarse, machine-raised raspteeth on one side and a very coarse filepattern on the other. Also suitable forsoftwood, plastics, soapstone, etc.Cross section 40 x 5 mmCut length 300 mmNo. 704563 22.52 € 26.80 €

H GLARDON/VALLORBE®

HABILIS RASPS, 5-PIECE SETPrecision rasps with rectangular handletangs. (60-64 HRC) 5-piece set: flat,half-round, triangular, square, round.Overall length 205 mmCut length 100 mmCut 3No. 704566 64.71 € 77.00 €

A FLAT RASP, EXTRA WIDECross section 40 x 4 mmCut length 240 mm, cut 4No. 704682 9.16 € 10.90 €

B SHOEMAKER'S RASP (4 VARIATIONS)Half-round, flat, each with a coarse raspand file cut. For leather and wood.Cross section 23 x 5 mmlength 200 mmNo. 704688 4.03 € 4.80 €

C RASP SET, 4-PIECEFour Schwertfisch rasps: 200 mm flatrasp, 200 mm cabinet rasp, 150 mmslim half-round rasp, 85 mm riffler.Cut 4No. 704579 22.94 € 27.30 €

D RIFFLER SETS, 8-PIECE8 rasps each, with different head shapes,suitable for a variety of applications instairbuilding and sculpting and soap-stone working. Cut 3.

SmallOverall length approx. 180 mmCut length approx. 50 mmNo. 704680 14.45 € 17.20 €

MediumOverall length approx. 190 mmCut length approx. 50 mmNo. 704559 15.88 € 18.90 €

LargeOverall length approx. 270 mmCut length approx. 70 mmNo. 704578 18.07 € 21.50 €

Tips for care:

When storing, avoid contact with oneanother and with other tools.Do not hang on magnetic bars.Store individually in a wooden rack.

If possible, wear thin cotton gloves whenworking, as the teeth edges corrode whenthey come in contact with sweat fromyour hands.

Clean clogged rasps with a brass brush (No. 705091), p. 120.

Remove residual resin by dipping the raspin balsam turpentine (No. 705288).

Tip for using:

Hold the rasp in both hands (one handat the tip and one on the handle) andlift the teeth from the workpiece whenreturning.

A B F

Machine-cut rasps

I GLARDON/VALLORBE®

NEEDLE RASPS, 6-PIECE SETPrecision needle rasps made of extrahard steel (60-64 HRC). Set, 6 pieces:flat, flat-pointed, half-round, triangular,square, round.Overall length 140 mmCut length 75 mmCut 4

C

E

D

No. 704565 48.40 € 57.60 €G H I

Price advantage

Rasps and files || Dreadnought rasps, plane- and sawrasps

115

Dreadnought rasps, plane- and sawrasps

A SAW RASPFine saw blade wrapped around an ovalwooden rod for working softwoods andmaking structures.Overall length 215 mmCut length 80 mm15 x 25 mmNo. 704689 3.53 € 4.20 €

B BLOCK RASPWith a wooden handle. Very coarse cutfor shaping wood, plaster, soapstone orhooves.Approx. 43 x 123 mmCut 1No. 704687 7.65 € 9.10 €

C SAW RASPJapanese turbo rasps:All woodworkers appreciate the cuttingperformance of Japanese hand saws.Ten sawblades arranged in a diamondpattern for this Japanese saw rasp createa tool for fast stock removal that doesnot clog. It is very versatile tool not onlyfor working wood but also for light metal,plastic and plaster. The saw bladescome with a tooth spacing of 2.5 and1 mm providing coarse teeth on oneside for fast stock removal and very fineteeth on the other side for clean-up work.Blade length 280Overall length 385 mmNo. 704540 16.72 € 19.90 €

D SAW RASP WITH CRANKED HANDLEThis saw rasp with cranked handle allowsworking with higher surface pressure mak-ing it particularly suitable when dressingflat stock. The blade is easily reversedand can be replaced.Blade length 260 mmOverall length 390 mmNo. 704541 20.08 € 23.90 €Repl. blade No. 704542 14.20 € 16.90 €

B

A

E MICROPLANE® PLANE RASPSMicroplane guarantees unsurpassed removal, dust-free work and smooth surfaces with hundreds of fine cutters. The rust-proof stainless-steel blades, are hardened to approx. 60 HRC and are extremely durable.

1 Microplane® plane rasp, roundCross-section 9 mmCut length 80 mmOverall length 160 mmNo. 705163 8.36 € 9.95 €

2 Microplane® plane rasp, flatCross section 26 x 8Cut length 200 mmOverall length 320 mmNo. 705169 16.76 € 19.95 €

3 Microplane® rotary shaperShaping head for use in drills, aluminiumbody with cutter insert.Length 70 mmØ 50 mmNo. 704988 20.97 € 24.95 €Repl. blade No. 704989 14.24 € 16.95 €

F SUPERHARD FILE RASPSSturdy rasps for glued joints, laminatesand synthetic materials as well as quickshaping in sculpturing. The extremelysharp teeth are arranged in an archedpattern to ensure efficient stock removaland smooth surfaces without clogging.Hardened to over 60 HRC for superiordurability.

1 Plastic handle, flat, coarse/mediumDouble-sided cut.Overall length 280 mmCut length 180 mmWidth 19 mmNo. 718091 14.71 € 17.50 €

Plastic handle, half-round, mediumSingle-sided cut.Overall length 280 mmCut length 180 mmWidth 19 mmNo. 718093 13.70 € 16.30 €

2 Handle tang, half-round, mediumSingle-sided cut.Overall length 200 mmCut length 120 mmWidth 16 mmNo. 711071 10.59 € 12.60 €

3 Handle tang, half-round, ultrafineSingle-sided cut.Overall length 200 mmCut length 110 mmWidth 10 mmNo. 711074 14.20 € 16.90 €

4 Pointed tang, flat, mediumSingle-sided cut.Overall length 245 mmCut length 200 mmWidth 20 mmNo. 711072 12.77 € 15.20 €

More Superhard file rasps are avail-able online at www.more-than-tools.de

D

C

E 1 2 3

F 1 2 3 4

116

Rasps and files || Files for metal working

Glardon/Vallorbe® filesThe traditional Swiss Glardon/Vallorbe®

Company makes top-quality precisionfiles which meet the high quality standardsof the watch industry. 200 years of experience come to the fore in excellentdurability and sharpness. The files aredesigned for working steel, but they areequally suitable for fine working of wood,aluminium, brass and hard plastics. Hardened to 64-65 HRC.

Files for metal working

A GLARDON/VALLORBE® FLAT FILESDouble cutSlender, with one narrow side cut.Cut Cross section Cross length000 22x5 mm 200 mm No. 705012 16.72 € 19.90 €

26x6.5 mm 250 mm No. 705039 23.45 € 27.90 € 00 17x2 mm 150 mm No. 705003 14.37 € 17.10 €

19x4 mm 150 mm No. 705192 12.02 € 14.30 € 22x5 mm 200 mm No. 705006 17.06 € 20.30 € 26x6.5 mm 250 mm No. 705009 24.54 € 29.20 €

0 10x2 mm 100 mm No. 704999 16.05 € 19.10 € 15x2 mm 125 mm No. 705001 13.87 € 16.50 € 17x2 mm 150 mm No. 705004 14.79 € 17.60 € 19x4 mm 150 mm No. 705193 13.03 € 15.50 € 22x5 mm 200 mm No. 705007 17.90 € 21.30 € 26x6.5 mm 250 mm No. 705010 25.63 € 30.50 €

1 12.5x3 mm 100 mm No. 705000 11.68 € 13.90 € 17x2 mm 150 mm No. 705005 15.46 € 18.40 € 19x4 mm 150 mm No. 705194 13.53 € 16.10 € 22x5 mm 200 mm No. 705008 18.82 € 22.40 € 26x6.5 mm 250 mm No. 705011 26.72 € 31.80 €

2 15x2 mm 125 mm No. 705002 14.87 € 17.70 € 17x2 mm 150 mm No. 705078 16.55 € 19.70 € 22x5 mm 200 mm No. 705013 19.75 € 23.50 €

3 22x5 mm 200 mm No. 705014 20.50 € 24.40 € 4 22x5 mm 200 mm No. 705035 21.51 € 25.60 €

Single cutFor better surface finishes, both narrow sides cut.Cut Cross section Cross length2 21x3 mm 200 mm No. 704901 5.63 € 6.70 € 2 25x4 mm 250 mm No. 704902 7.90 € 9.40 €

A

B GLARDON/VALLORBE® WARDING FILESSlender, with cut sides.Cut Cross section Cross length0 15.4x1.7mm 150 mm No. 704923 16.55 € 19.70 € 2 15.4x1.7 mm 150 mm No. 704924 18.07 € 21.50 €

C GLARDON/VALLORBE® CROSSING FILESCut Cross section Cross length00 21x6 mm 200 mm No. 705032 48.15 € 57.30 € 0 15x4.5 mm 150 mm No. 705030 33.36 € 39.70 €

21x6 mm 200 mm No. 705033 50.34 € 59.90 € 1 15x4.5 mm 150 mm No. 705031 33.95 € 40.40 €

21x6 mm 200 mm No. 705034 52.69 € 62.70 €

D GLARDON/VALLORBE® HALF-ROUND FILESCut Cross section Cross length000 21x6 mm 200 mm No. 705086 31.26 € 37.20 € 00 15x4.5 mm 150 mm No. 705022 23.61 € 28.10 €

21x6 mm 200 mm No. 705025 31.60 € 37.60 € 0 13x4 mm 125 mm No. 705020 23.36 € 27.80 €

15x4.5 mm 150 mm No. 705023 24.79 € 29.50 € 21x6 mm 200 mm No. 705026 33.03 € 39.30 €

1 15x4.5 mm 150 mm No. 705024 25.97 € 30.90 € 21x6 mm 200 mm No. 705027 34.62 € 41.20 € 15x4.5 mm 150 mm No. 705068 28.32 € 33.70 € 21x6 mm 200 mm No. 705087 38.74 € 46.10 €

3 15x4.5 mm 150 mm No. 705069 29.58 € 35.20 €

E GLARDON/VALLORBE® HALF-ROUND FILES, SLIMFiles for bow tips, violin f-holes.Cut Cross section Cross length0 10x3 mm 150 mm No. 705028 27.48 € 32.70 € 2 10x3 mm 150 mm No. 705029 30.42 € 36.20 €

The cut specifications for Glardon/Vallorbe® files arein accordance with the Swiss norm.

Cut table Swiss cut German cutextra coarse (for wood) 000 1very coarse (for wood) 00 1coarse (for wood) 0 1medium (for wood) 1 2fine (for wood/metal) 2 3very fine (for metal) 3 4extremely fine (for metal) 4 5

The density and height of the teeth depend on both the cut number and the length of the file.

B C D E

Blade ShoulderTang

GroundCut length


117

A GLARDON/VALLORBE® ROUND FILESHighest precision files, cut extends rightto the tip.

Cut Cross section Cross length1 0 4 mm 150 mm No. 705097 14.96 € 17.80 € 2 5 mm 120 mm No. 705099 10.67 € 12.70 € 3 1 1.5 mm 75 mm No. 705094 13.11 € 15.60 € 4 3.3 mm 90 mm No. 704926 6.55 € 7.80 € 5 3.6 mm 100 mm No. 704927 7.65 € 9.10 € 6 8 mm 190 mm No. 704922 15.21 € 18.10 € 7 2 0.8 mm 38 mm No. 705092 9.08 € 10.80 € 8 1 mm 50 mm No. 705093 9.58 € 11.40 € 9 1.5 mm 55 mm No. 705066 9.08 € 10.80 € 10 2 mm 65 mm No. 705057 9.08 € 10.80 €

B GLARDON/VALLORBE® NEEDLE FILESFor precision work on metal and wood.With round, knurled steel handle.Hardened to 64-66 HRC.Cut 0 = coarse, cut 1 = fine.Overall length 140 mmCut length 75 mmØ tang 3 mm

Form Cut1 Flat 0 No. 705140 4.87 € 5.80 €

1 No. 705040 4.87 € 5.80 €2 Warding 0 No. 705141 5.71 € 6.80 €

1 No. 705041 5.71 € 6.80 €3 Three-square 0 No. 705142 5.71 € 6.80 €

1 No. 705042 5.71 € 6.80 €4 Square 0 No. 705143 5.71 € 6.80 €

1 No. 705043 5.71 € 6.80 €5 Round 0 No. 705144 4.87 € 5.80 €

1 No. 705044 4.87 € 5.80 €6 Barette 0 No. 705145 5.71 € 6.80 €

1 No. 705045 5.71 € 6.80 €7 Half-round 0 No. 705146 6.22 € 7.40 €

1 No. 705046 6.22 € 7.40 €

1A 2 3 4 5 6 7 8 9 10 B

Glardon/Vallorbe® needle files,6-piece set

Cut 0 No. 705054 31.85 € 37.90 € Cut 1 No. 705053 31.85 € 37.90 €

1 2 3 4 5 6 7

Flat, half-round,square, triangular,round, barrette.

5-piece set in case:Flat, half-round, three-squaresquare, round.

Glardon/Vallorbe® habilis files, 5-piece set

No. 704935 51.85 € 61.70 €

C

C GLARDON/VALLORBE®

HABILIS FILESHabilis files have slender square tangswhich serve as handles, making themsuitable for particularly delicate work.60-64 HRC.Cut length 105 mmOverall length 215 mmCut 1

Form Cross-section1 Flat 10x2.6 mm No. 704930 10.34 € 12.30 €2 Half-round 12.2x3.4 mm No. 704931 13.11 € 15.60 €3 Three-square 9.4 mm No. 704932 11.01 € 13.10 €4 Square 5.8x5.8 mm No. 704933 11.60 € 13.80 €5 Round 6.5 mm No. 704921 8.07 € 9.60 €

1 2 3 4 5

Price advantage

Price advantage


118

Diamond filesFor hardened steel, hardened metal,glass, ceramics etc.

A DIAMOND NEEDLE FILE SET, 10-PIECEFlat 6 x 1.5 mm, half-round 5 x 2 mm,square 2.5 mm, three-square 3.5 mm,round 3 mm, warding 5 x 1.5 mm, knife-shaped 5 x 1.5 mm, barrette 5 x 2 mm,crossing 5 x 2 mm, crossing 3.5 x 2.5 mm.Coarse grain.Overall length 140 mmCoating length approx. 50 mmNo. 711044 20.59 € 24.50 €

B DIAMOND FILE SET, 5-PIECEFlat 9 x 2.3 mm, half-round 9 x 3 mm,square 4.5 mm, three-square 6 mm,round 5 mm. Coarse grain.Overall length 180 mmCoating length approx. 70 mmNo. 711045 13.87 € 16.50 €

C DIAMOND FLAT FILE SET, 4-PIECEThin flat files with diamond plates, idealfor tight spaces, for sharpening machinecutters, milling equipment, tools and hardened metal blades.Extra-fine, fine, medium, coarse grain.Overall length 150 mmPlates 19 x 50 mmNo. 711046 18.91 € 22.50 €

A B C

D GLARDON/VALLORBE®

VALTITAN FILESThe perfect files for knife-makers:At 72 HRC, they are the hardest of alltoothed files. They allow materials whichhad been considered impossible to file,e.g. hardened steel, sintered steel, HSSetc. to be filed without breaking teeth.Other advantages: Valtitan files do notclog, they are largely rust-proof and evenmore powerful. They impress users withgreater chip removal and longer servicelife. Guaranteed workability of materialsup to 65 HRC.

1 Flat fileOne narrow side cutCross section 21.4 x 4.8 mmCut length 200 mmCut 0No. 704400 24.62 € 29.30 €

2 Pillar fileCross section 14.5 x 4.5 mmCut length 200 mmCut 0No. 704401 25.88 € 30.80 €

3 Half-round fileCross section 15.3 x 4.7 mmCut length 150 mmCut 0No. 704402 30.17 € 35.90 €

4 Round fileØ 7.5 mmCut length 200 mmCut 0No. 704403 21.26 € 25.30 €

D 1 2 3 4

Files for knife makers E CHECKERING FILE

No. 704410 31.01 € 36.90 €

F MILL SAW FILEThe ideal file forthe ambitious knifemaker, who makeshis own blades. Theround edges help tofile the transitionfrom the blade tothe ricasso, an areawhich is an importantattribute of a highquality blade.

Cross section 20 x 4 mmLength 200 mmNo. 704411 6.64 € 7.90 €

E F

To prevent the fingers from slipping, check-erings are cut into knife handles and onthe backs of blades. The checkering fileis especially suited for this task. The extraordinary cut originates throughlengthwise grooves inthe blade which arecrossed by 90° grooves.Through this cut smallteeth are formed whichcut on the push stroke.To produce the check-ering the file is movedin one spot forward and backwards.Suited for wood, non-ferrous metals and unhardened steel.Cross section 19 x 5.2 mmCut length 150 mmCut 00

Rasps and files || Files for wood-based materials

119

A F.D. CABINET WOOD FILEThe classic file for cabinet-makers.Cut 1.

1 Length 250 mmCross section 29 x 5.3 mmNo. 704430 13.61 € 16.20 €

2 Length 300 mmCross section 35.5 x 6 mmNo. 704431 16.72 € 19.90 €

B F.D. WOOD FILE HALF-ROUNDSpecial knife cut for high efficiency.Cut 0.

E PRECISION HAND GRINDERS NTLasts 50x longer than sandpaper:For fine work in making models andmusical instruments, also suitable fordeburring aluminium and plastic parts.Particularly suitable for controlled remov-al of material in hard-to-reach areas,grinds in both directions. Sturdy diecastaluminium handle, shoe with easy toremove and replace hardened steelgrinding plate. Please sand on a samplepiece first. Surface of the sanding padmay leave black stains during first use(anti-corrosion coating). This is not a signof bad quality and only needs to be doneduring first contact with wood.

1 Sanding platen triangular, pointedLength 80 mm, width 7-28 mmNo. 705126 6.30 € 7.50 €

2 Sanding platen rectangular, slimLength 150 mm, width 24 mmNo. 705127 8.32 € 9.90 €

3 Sanding platen rectangular, broadLength 150 mm, width 50 mmNo. 705128 10.50 € 12.50 €

Replacement grinding plateNo. 705129 2.77 € 3.30 €



A 1 2

E 1 2 3

Tips for using:

Roughening thesurfaces whichlater need to beglued together produces a stronger bond.

Files for wood-based materials

1 Cut length 200 mmCross section 21 x 6 mmNo. 704433 10.84 € 12.90 €


1 2

C F.D. ALL PURPOSE FILES


2 Cut length 250 mmCross section 25 x 6.3 mmNo. 704435 10.00 € 11.90 €

1 2

D CRANKED FILE SET, 5-PIECEThere are situations like set-offs orrecesses in a surface in which you findyourself in difficulties with an ordinarystraight file. In such cases our Japanesecranked files will come in handy.The 5-piece set contains the shapes flat,square, round, half-round and cabinet.Medium cut. Overall length 215 mmHead length 65-75 mmNo. 711090 65.46 € 77.90 €

D

B C

Ideal for general use due to the two dif-ferent cuts on the flat sides. The roughside is used to remove material quicklywhile the finer side is suited for surfacefinishing. Recommended for wood, softmetals and plastic. Plastic handle.One narrow side cut.Cut 0.

Handle chart for rasps and files: Multiple orders possible for each item.

701618 701619 701616 701617 701605 701606 701604 701601 701602 701603 704952 704955 704956fits No. fits No. fits No. fits No. fits No. fits No. fits No. fits No. fits No. fits No. fits No. fits No. fits No.

704502 704502 704403 704400 704402 704400 704502 704401 704400 704400 704400 704402 704451704673 704574 704452 704401 704574 704401 704574 704402 704401 704401 704430 704450 704502704676 704670 704455 704403 704673 704403 704673 704403 704403 704430 704432 704453 704579704741 704673 704551 704430 704676 704430 704676 704450 704450 704432 704672 704553 704670705029 704674 704575 704432 704677 704432 704684 704452 704452 704454 704675 704572 704674

704677 704678 704450 704684 704450 704733 704453 704453 704569 704727 704720 704677704684 704704 704453 704704 704454 704741 704455 704455 704570 704902 704721 704684704704 704716 704553 704733 704553 704923 704551 704553 704572 705006 704722 704709704733 704732 704569 704999 704569 704924 704575 704569 704573 705007 704724 704741704741 705003 704570 705000 704570 704999 704677 704570 704576 705008 704901 704923704923 705004 704572 705001 704572 705000 704678 704572 704577 705013 705022 704924704924 705005 704573 705002 704573 705001 704684 704574 704683 705014 705023 705010705000 705078 704576 705020 704575 705002 704704 704576 704685 705025 705024 705011705002 711087 704577 705022 704576 705028 704716 704671 704707 705026 705030 705028705022 704671 705023 704577 705029 704732 704672 704720 705027 705031 705029705023 704672 705024 704585 705099 704922 704675 704721 705032 705068 705031705024 704675 705030 704671 704923 704678 704722 705033 705069 705039705028 704678 705031 704672 704924 704685 704727 705034 705192705030 704682 705068 704675 705003 704686 704901 705035 705193705031 704683 705069 704678 705004 704707 704902 705086 705194705068 704685 705099 704682 705005 704720 705006 705087705069 704686 704683 705022 704721 705007705097 704707 704686 705023 704722 705008705099 704720 704704 705024 704724 705012

704721 704707 705030 704901 705013704722 704720 705068 704922 705014704724 704721 705069 705003 705025704901 704722 705192 705004 705027704902 704724 705193 705005 705032704922 704727 705194 705006 705086705006 704901 705007 705087705007 704922 705022 711072705008 705006 705023705012 705007 705024705013 705008 705025705014 705012 705026705025 705013 705027705026 705014 705030705027 705025 705032705032 705026 705033705033 705027 705034705034 705032 705068705035 705033 705069705086 705034 705086705087 705035 705087705192 705086 705192705193 705087 705193705194 705192 705194711072 705193

705194711072711087

Rasps and files || Handles and accessories

120

A ROSEWOOD HANDLESPatterned after old English models andturned from fine East Indian rosewood.Polished heavy duty ferrule.

1 Slim drop-shaped designFerrule Ø Length15 mm 85 mm No. 701618 3.28 € 3.90 €18 mm 85 mm No. 701619 3.28 € 3.90 €

A

2 Elegant octagonal designFerrule Ø Length15 mm 130 mm No. 701616 5.38 € 6.40 €18 mm 130 mm No. 701617 6.39 € 7.60 €

B UNIVERSAL HANDLESOctagonal, with a round neck. UntreatedSwiss pear wood.Ferrule Ø Length15 mm 90 mm No. 701605 4.71 € 5.60 €19 mm 120 mm No. 701606 5.21 € 6.20 €

D BALL-SHAPED HANDLEPolished boxwood, powerful tang ferrule.Ferrule Ø Length18 mm 105 mm No. 701601 2.61 € 3.10 €20 mm 105 mm No. 701602 2.61 € 3.10 €22 mm 105 mm No. 701603 2.61 € 3.10 €

C DROP-SHAPED HANDLEPolished boxwood, powerful ferrule.Ferrule Ø Length16 mm 70 mm No. 701604 2.35 € 2.80 €

E SCREW-THREAD HANDLESFor files with pointed tangs, fastening viainternal threads, plastic.Internal Thread Ø Length7 mm 105 mm No. 704955 4.12 € 4.90 €9 mm 105 mm No. 704952 4.12 € 4.90 €11 mm 120 mm No. 704956 4.37 € 5.20 €

F FILE CLEANERFor cleaning file and rasp teeth. Beech-wood with brass fittings.Overall length 250 mmHead 40 x 100 mm No. 705091 7.48 € 8.90 €

Handles and accessories

1

2

B

C

D E

F

A1 A2 B C D E

Precision provides safety!

121

Measuring instruments | 122

Rules | 122

Folding rules and tape measures | 123

Callipers and micrometers | 124

Protractors | 124

Scribing tools | 125

Marking gauges | 125

Chalk lines and marking tools | 125

Compasses and accessories | 126

Inspection and transferring instruments | 126

Squares | 126

Sliding bevels and profile gauges | 129

Flatness inspection | 129

Inclination measuring tools and moisture meter | 130

Surveying tools | 131

Optical survey | 131

Retrievers, pickups and tweezers | 131

Workshop knives | 132

Marking and veneer knives | 132

Scalpels and craft knives | 132

Measuring and inspection instruments || Measuring instruments

122

Measuring instruments

Rules

A PRECISION RULESHighly wear-resistant rule made of hardchrome-plated stainless steel. Hard-ened with milled edges. Matt finish anddeep-etched.

1 Shinwa® precision rule, 1.5 metreThis flexible 1.5 m-long rule fromShinwa is extremely precise and excep-tionally easy to read. Use it for preciselymarking or measuring even large work-pieces. Made of hardened spring steel, itis guaranteed to keep its shape for yearsto come. Hardchrome-plated surface witha deep-etched, wear-resistant grind, withburr-free side edges for maximum linearity.Scale length 150 cmWidth 40 mmThickness 2 mm1000 gNo. 717126 91.60 € 109.00 €

2 Semi-rigid designThickness 1 mmWidths 25/30/35 mmLength300 mm No. 707255 7.31 € 8.70 € 600 mm No. 707256 12.52 € 14.90 € 1000 mm No. 717127 20.92 € 24.90 €

3 Flexible versionThickness 0.5 mmWidth 15 mmLength150 mm No. 707263 3.28 € 3.90 € 300 mm No. 707264 6.47 € 7.70 € 600 mm No. 717129 11.68 € 13.90 € 1000 mm No. 717128 20.08 € 23.90 €

4 Rule, Ultra-flexible versionMeasure around the curve:Highly flexible rule for measuring andmarking curved surfaces and small an-gles, e.g. when turning, in model con-struction, boat building etc. Stainlesssteel, high-accuracy deep-etched mmscale.Thickness 0.15 mmWidth 13 mmLength200 mm No. 707270 5.38 € 6.40 € 300 mm No. 707271 7.06 € 8.40 € 600 mm No. 707272 12.52 € 14.90 €

B VERITAS® RULE STOPSave time with repeat measurements: The stopper is slid on a metal rule or theleg of a square and fixed in the chosenposition with a knurled screw. The slip-proof stopper made of aluminium is suit-able for rules up to a thickness of 1.2mm and a width of 22 - 28.5 mm.No. 703632 13.11 € 15.60 €

Length600 mm No. 707156 41.93 € 49.90 € 1000 mm No. 707157 50.34 € 59.90 €

E SHINWA® CUTTING RULERigid aluminium cutting rule with hardened steel edgefor protection againstwear. Deep-etchedmm scale, rubber pad.Length 1000 mmWidth 56 mmNo. 717124 26.47 € 31.50 €

F FLEXIBLE RULEFlexible rule for marking, scribing ortransferring curves and arches. Vinyl witha lead core, mm and inch scale, inkingedge.Length 600 mmNo. 708094 4.45 € 5.30 €

A

1

2

3

4

B

D

E

F

C

C CUTTING RULE WITH DOUBLE STEEL EDGEThis wide cutting rule with steel edges on both sides and adeep-etched scale isideal for precisestraight cuts. The holl-ow-section aluminiumprofile makes it light and robust at thesame time. The handle and textured sur-face allow the rule to be guided safelyand also used vertically. The doubleflutes on the bottom prevent the rulefrom slipping even on smooth surfaces.Width 90 mmLength600 mm No. 717159 46.97 € 55.90 € 1000 mm No. 717160 55.38 € 65.90 €

D SHINWA® CUTTING RULE WITHHANDLEThe deep-etched scaleand steel edge makethis wear-resistant alu-minium cutting rulean ideal tool for pre-cise square cuts. The rubber pad on theunderside prevents slipping and the rubber-coated handle provides protectionfrom incision wounds while also allowingthe tool to be used in a vertical position.Width 60 mm


123

Folding rules and tape measures

A HULTAFORS® FOLDING RULEWhen it comes to professional qualityfolding rules, there’s only one choice: theSwedish folding rules from Hultafors -synonymous with uncompromising quality since 1883.

1 Hultafors® downy birch folding ruleLight and break-proof:Made of the finest Swedish glass birch,this folding rule has cult status. Despiteits lightweight construction, with wood just2 mm thick, it is extremely resistant tobreakage. The flush-fitting pivots are madeof hardened Swedish steel, guaranteed toshow no signs of wear, even after years ofuse. Millimetre markings on both sides.Length 2 mWidth 17 mm240 mm when folded92 gNo. 708024 6.64 € 7.90 €

2 Hultafors® fibreglass folding ruleExact 90° locking:Locking into place atexactly 90°, this po-lyamide Swedish ruleis an extremely versatile tool. Reinforcedwith fibreglass, it is extremely durableand very stable. The measuring scale isimprinted on both sides, making it easyto read even after years of use.Length 2 mWidth 15 mm240 mm when folded138 g No. 708025 5.80 € 6.90 €

C WOOD STOCK® FOLDING RULEWood-grain collection and folding rule in one:Each segment ofthis folding rule is made from adifferent type ofwood. The frontside has a clearscale and the rearside provides information on thedistribution, characteristics and use ofeach tree. The folding rule not only provides correct measurements but alsooffers a fun introduction to the world ofwood. All wood used is FSC-certified andthe rule comes in an attractive black sliding box.Our tip: Also ideal as a gift – not just forcraftsmen!Length 2 m

B WHITE BEECH FOLDING RULEWhite beech folding rule with 2.7 mmthick segments and patented locking-cam mechanism. Millimetre scale onboth sides.Length 2 mWidth 16 mm240 mm when folded80 gNo. 708031 2.94 € 3.50 €

F HARDWOOD TAPE MEASURESGood in the hand:Handmade cases from selected hard-woods. Inch/mm scale markings.Length 2 mCase 50 x 50 x 14 mm

1 RosewoodNo. 707160 8.32 € 9.90 €

2 EbonyNo. 707158 10.00 € 11.90 €

D TALMETER® MARKING MEASUREPrecise and indestructible:The Swedish Talmeter marking measurescombine the highest precision with infalliblemechanical design. The reliable lockingmechanism, clear scale markings and in-dicator help prevent measurement errors.The extension allows accurate insidemeasurements to be made. An additionalcalibration scale lets you directly measurediameters of round objects. The edges atthe tip of each measure and on the baseof the casing allow a measurement to bedirectly transferred to the workpiece.High precision, complies with standardISO EU II.

1 Length 2 mTape width 16 mmNo. 708020 15.04 € 17.90 €

2 Length 3 mTape width 16 mmNo. 708021 18.40 € 21.90 €

3 Length 6 mTape width 25 mmHigh rigidity, with position locking.No. 708023 39.08 € 46.50 €

F

21

2

D

1

3

2 Brazilian woodsAmapá, Jatobá, Louro Gamela, LouroItauba, Louro Preto, Muiracatiara,Muirapiranga, Pau Amarelo, SucupiraVermelho, Violeta.No. 708030 19.24 € 22.90 €

1 Native woodsSycamore, birch, oak, alder, ash, sweetchestnut, cherry, larch, robinia, beech.No. 708029 16.72 € 19.90 €

1 2

A

1 2

C

B

E

E STANLEY® MINI RETRACTABLE TAPEMEASURE, 3 METERSSmall retractable tape meas-ure with locking mechanismand high-impact housing. Ea-sily fits into any pocket or,thanks to the belt clip, can be worn on abelt. The polymer coating makes the tapehighly wear-resistant and the anti-re-flective finish means the scale is easy toread even in direct sunlight.Tape width 13 mmNo. 707287 3.45 € 4.10 €


124

Callipers and micrometers A DIGITAL CALLIPERSMulti-purpose callipers with a large five-digit LCD display for internal and exter-nal depth measurement. Display can beswitched between mm/inch. Resolutionof 0.01 mm. Display can be zeroed atany position. Beam and jaws of stainlesssteel, hardened faces, incl. 1.5 V battery,plastic case.

1 Measuring range 150 mmTip length 40 mmNo. 707170 33.53 € 39.90 €

2 Measuring range 100 mmTip length 30 mmNo. 707258 29.33 € 34.90 €

B DIAL CALLIPERA sturdy dial caliper with a shock- anddust-proof analogue dial indicator, ideal forworkshop use. Stainless steel slide anddial, with hardened faces, two screws forlocking the slide and calibration ring inplace; accurate to within 0.01 mm, plastic case.Measuring range 150 mm.No. 707259 28.49 € 33.90 €

C SHINWA® PLASTIC DIAL CALLIPERExtra-light and durable GRP dial callipersthat are gentle on the workpiece. Recommended for mobile use and for measuring sensitive parts, e.g. in restoration work. External, internal anddepth measurements. 1/10 display accuracy, with wall bracket.Measuring range 150 mm44 gNo. 707225 20.92 € 24.90 €

D PRECISION CALLIPERBevelled scale for parallax-free reading.Deep-etched stainless steel, slide with locking screw, 0.05 mm vernier.Measuring range 150 mm.No. 707303 15.88 € 18.90 €

E MINI POCKET CALLIPERLightweight, compact caliper for taking in-side and outside measurements of smallor delicate objects, models, veneers, etc.Stainless steel, deep-etched graduationswith a 0.05 mm vernier scale.Measuring range 70 mmJaw length 19 mm23 gNo. 707243 12.52 € 14.90 €

F SHINWA® MICROMETERMicrometer for high-precision measure-ments with 0.01 mm accuracy. Easy toread thanks to deep-etched scale, highrepeat accuracy thanks to adjustabletightening torque. Carbide-tipped sensingheads, locking lever, powder-coated cast-iron frame, incl. case.Measuring range 0-25 mmJaw depth 20 mmNo. 707278 35.63 € 42.40 €

G KÄFER® CALLIPERSFor measuring the wall thickness of mu-sical instruments, cladding, hollow bo-dies and veneer etc. Robustcast-aluminium frame with precision dialgauge. Measuring range is 30 mm, dis-play accuracy is 0.1 mm. A left-handedversion is available on request.Jaw depth 200 mmNo. 707101 172.18 € 204.90 €

A

B

Protractors

H PRECISION PROTRACTORSWith highly precise angle markings, running in both directions (0° - 180°),stainless steel.

1 Scale width 90 mmSide length 150 mmNo. 717148 12.35 € 14.70 €

2 Scale width 120 mmChrome-plated, matt surface with deep-etched scale.Side length 238 mmNo. 717140 25.13 € 29.90 €

J JAPANESE MINI PROTRACTOR

No. 717141 10.00 € 11.90 €

I STARRETT® MITRE ANGLE GAUGERead the mitre angle:With the Starrett protractor, you can readboth the mitre angle and half angle andthen immediately transfer them to thesaw setting. Protractor with double scale,solid aluminium.Side length 300 mmNo. 718300 100.00 € 119.00 €

K ANGLEFIX® MITRE GAUGEThis mitre gaugemakes it easier toquickly transfermitre angles withoutmaking mistakes.The bevels with integrated conversionhalve the measured angle and indicatethis with a metal tongue. High-qualityplastic body, encapsulated conversionmechanism, steel flag.170 x 145 mmNo. 707249 15.04 € 17.90 €

L NOBEX® MITRE GUIDESaves time andavoids inaccuraciesin installations andcarpentry jobs. Formeasuring any exter-nal or internal angle (2 ), and transferringthe correct mitre angle ( ) directly to theworkpiece or saw. With angle markings.Aluminium.Side length 320 mmNo. 707248 38.57 € 45.90 €

H

1

C

D

2

E

F

G

1 2

J

K

I

L

Arm for chamfer angle with tool blades.With scale markings.Side length 100 mm

Measuring and inspection instruments || Scribing tools

125

A VERITAS® MARKING GAUGEPrecise scribing guaranteed! The cuttingwheel is bevelled on one side only, facilita-ting accurate and reliable results evenwhen cutting end grain or difficult grainpatterns. Jerk-free adjustment thanks toprecision guide with friction brake. Steelrod, hardened cutter, anodised aluminiumhead with brass fence and adjustmentscrew. Deep-etched scale in mm.Working range 0 - 150 mmNo. 707178 28.49 € 33.90 €

B VERITAS® MICRO-ADJUST MARKINGGAUGEFeatures a micro-adjustment mechanismfor highly accurate markings. Otherwiseas above.No. 703656 37.73 € 44.90 €

Replacement blades for marking gaugescan be found at www.more-than-tools.de

C MINI PRECISION MARKING GAUGECan be used with a needle or scribing knife:This compact marking gauge isan ingenious scribing tool forwood joints, small wooden ob-jects, model making and craftcarpentry. It can be fitted with astraight or disc-shaped scribingknife or a needle, according topreference. The fence, which islocked in place with a clampingsleeve, may also be adjustedwith one hand; its asymmetricshape makes precise scribingpossible, even on thin workpieces.Includes 12 straight blades, 1 disc knife,1 needle.Working range 0-85 mm65 gNo. 703645 22.27 € 26.50 €

A

B

Scribing tools

Marking gauges

D ULMIA® MARKING GAUGE WITH DISC KNIFEThe mark is not scrat-ched, but cut with adisc knife, without tearing. While scriberstend to follow thegrain, the disc knife,which is bevelled on one side, holds anexact course even with difficult fibreflows. The disc knife can be easily remo-ved and sharpened. Two marking gaugeheads made of hornbeam with inlayedmeasurement scales 0-150 mm, headwith hardwood sole, brass locking screws.No. 707164 43.28 € 51.50 €

Precisely manufactured marking gaugefrom England with two scribe needles,one separately adjustable via a slider andsetscrew. This results in high repetitionaccuracy and saves time when markingparallel scribings for tenons and grooves,etc. An additional scribing needle on theopposite side of the arm can be used forsimple scribing. Rosewood with brass fittings.Working range 0-110 mmNo. 707196 38.49 € 45.80 €

Beautiful handy marking gauge of varn-ished rosewood, made in England. Thewedge-locked V-cutter cuts the fibre,which helps it stay true.Working range 3-110 mmNo. 707175 13.03 € 15.50 €

G JAPANESE MARKING GAUGESJapanese marking gauges are equippedwith single-bevel cutting blades, allowingthem to leave very fine, tear-out-free marksin end grain and other difficult grain patt-erns. The clean marks then serve as aperfect guide for cutting mortises with achisel. Keshiki can also be used to scorethin boards or thick veneers for subsequentsplitting. Made from durable Japanesewhite oak.

Graduated markings to 60 mmWorking range 0-120 mmNo. 717100 10.50 € 12.50 €Repl. cutter No. 717108 2.18 € 2.60 €

Working range 0-150 mmNo. 717101 16.47 € 19.60 €Repl. cutter No. 717108 2.18 € 2.60 €

3 Dual cutters, screw clampingFor marking parallel lines. Working capacity 0-90 mmNo. 717107 12.52 € 14.90 €

H JAPANESE PRECISION SLIDINGMARKERAn exceptional tool for marking grooves,rabbets, mortises and borings in wood-working as well as exact measurementsin metalworking, exact to a tenth of amillimetre. T-shaped stop and slider ofhardened stainless steel, etched measu-ring scale which is satinated for anti-re-flection. Chamfered slider with lockingscrew, 0.05 mm vernier. Slider width 90 mmMeasuring range 175 mm185 gNo. 707252 81.43 € 96.90 €

E

1

F

3

H

D

C

Chalk lines and marking tools

I INK LINE (SUMITSUBO)

No. 717298 32.69 € 38.90 €Repl. thread No. 717291 2.94 € 3.50 €

J SHINWA® MINI INK LINEProfessional quality, compact Sumitsubo.Ink not included. Operating instructionsincluded.Body length 130 mmThread length 15 mNo. 717299 20.08 € 23.90 €

K LIQUID INKFor ink lines, water-soluble.1 BlackContent180 ml No. 717305 4.03 € 4.80 €2 Red100 ml No. 717304 4.79 € 5.70 €

L CHALK LINE POWER WINDERChalk line with hand crank, 3.5:1 gearratio for fast rewinding, and fast unwin-ding without turning the crank. Chalkview window in high-impact ABS plastichousing lets you see exactly how muchchalk you have left. Slide-in compart-ment for quick filling, steel crank andhook fold into the case. Chalk not provi-ded.135 x 75 x 50 mmString length 30 mNo. 707288 14.20 € 16.90 €

M CHALK FOR CHALK LINEFor reliable markings, blue.225 gNo. 717296 6.64 € 7.90 €

M

N DREI STERNE® MARKING CHALKFatty additives make these pens weather-proof, light-fast and non-erasable. You canlabel almost anything with this, especiallyoutdoors: wood, iron, sheet metal, card-board and jute. Box with 12 pens.100 x 9.5 mmBlue marking chalkFor woodworkers.No. 707357 4.79 € 5.70 €Yellow marking chalkFor metalworkers.No. 707358 5.97 € 7.10 €

O LETTER & NUMBER AUTOMATICPUNCH SETMarking your tools and workpieces helpsavoid misunderstandings. With this setyou can easily mark wood and non-harde-ned metal. The knurled brass handle isspring-loaded, so you don’t need a hammer.Simply insert a letter or number bit intothe hexagon socket and press down. Letters are approximately 4 mm high.Comes in plastic box.No. 708324 15.55 € 18.50 €

2

I

J

K

1 2

L

N

O

E CROWN® PATENTED MARKING GAUGE

F CROWN® MINI MARKING GAUGE

1 Single cutter, wedge lock

2 Single cutter, screw clamping

Similar in function to a chalk line, a Su-mitsubo is used to mark straight lines onwood and other materials. A fine silk lineis drawn out through an ink-soaked wadof cotton, tensioned and then snappedagainst the workpiece. This allows you tomark very long (up to 10 m), fine and ex-ceptionally accurate lines, also on un-even workpieces. Can also be used as aplumb line. Unbreakable plastic bodyand thread bob. Incl. 15 ccm liquid ink.Operating instructions included.Body length 180 mmThread length 20 m

G

Measuring and inspection instruments || Scribing tools, Inspection and transferring instruments

126

Compasses and accessories

A VERITAS® LOG SCRIBE (SCRIBER)Essential for building log cabins:

No. 707269 88.24 € 105.00 €

Elegant French compasses made of gun-metal finished steel, with hardenedpoints, quick-acting screws.

E HINGE COMPASSWith pencil holder, quarter-circle divisionsand setscrew, santinated carbon-steel.Shaft190 mm No. 707345 28.74 € 34.20 € 310 mm No. 707346 37.82 € 45.00 €

D VERITAS® BEAM COMPASS HEADSFor making compassesof any size. Two alumi-nium heads with pencilholders and steel points,one of which is eccen-tric to facilitate fine ad-justment. Brasshardware. Can be mounted on any thinpiece of wood.No. 707231 41.93 € 49.90 €

C KUNZ® COMPASS HEADSFor building beam compasses. Grey castiron heads with pencil holders and steelpoints.Max. opening 30 mmNo. 707217 18.49 € 22.00 €

I PARALLEL MARKERUnspectacular but essential:Ideal for markingbuilt-in elements,joints, door casings,etc. Guide it along thereference surface andthe adjustable pencildraws the marking line. Can also be usedas a circular marker, thanks to the (removable) steel pin in the lower shaft.Plastic.Opening 4-75 mmNo. 716152 5.46 € 6.50 €

H POINT.2.POINTFor laying out equalspacings, e.g. fordovetails, dowels,etc. Extends to 600mm and can be lock-ed in any positionto transfer up to 8 position markings (7equal spacings) to the workpiece. Stain-less steel, with brass screws. Not suit-able for high-precision applications.Max. extension 600 mmNo. 707267 20.76 € 24.70 €

F PANTOGRAPHClassic tool: The pantograph (Greek for all-round wri-ter) transfers drawings, contours and pro-files in the same, larger or smaller scalefrom the plan to the workpiece - and thussaves a detour via the computer and pho-tocopier. With the help of the milledscale and fixing nuts made of solid brass,the transfer ratio can be adjusted from10x enlargement to 10x reduction. Notsuitable for high-precision requirements.Length 500 mmNo. 708095 25.13 € 29.90 €

G TRISCRIBE® MARKING HEADSConvert a try squareinto a precision mark-ing gauge, or a flat rule(up to 2.5 mm thick)into a practical measuring compass.

Two marking heads, hardened needle in-sert, cutter insert with replacementblade, can also be used with pencil (included). Aluminium body. Rule not included.No. 707268 21.76 € 25.90 €

A

B

C

0

Squares

J

J FLEXIBLE SQUARE (SASHIGANE)This light and easy-to-read stainless steelsquare is used notonly as a framingsquare and scale, butalso as an angle of inclination and trysquare. The blade isexactly 15 mm wide,the standard measure-ment in Japan for tenons and boardthicknesses. The frontof the square has theusual deep-etchedmetric markings (mm).The back has two special calibrations:one gives the diameter (x 3.14) and theother the length of one side of a squareinscribed by that diameter (x 0.7). The be-velled edges and slight hollow grind pre-vent ink markings from being smudged.Shaft length 150 / 250 mm.

K JAPANESE CARPENTER'S SQUAREPrecision square with mm graduationspermanently etched on both sides ofboth edges. Stainless steel.Shaft length 150 / 250 mm

Tips:The Sashigane500 mm canalso be used asa try square.Simply bend the longer side slightlyand place it flush against the work-piece.

Check the accuracy of the Sashigane onany straight edge by marking a perpen-dicular line, turning the square overand remarking the same line. If the lineis not identical, the square is inaccu-rate and should be adjusted. To correct

an inaccurate square, place the cornerof the Sashigane on an anvil. If theangle is too large, lightly tap the out-side corner (A) with a small hammer. If the angle is too small, tap the insidecorner (B). The hammer blows mis-shape the steelslightly, causing itto open or close.Do not strike toohard, and recheckthe angle often.

A

B

Anvil

Squ

are

1 2

D

E

F

G

H

I

K

For transferring contoursto round stock, especiallyfor marking corner notches(on modular systems). Thetwo built-in levels allow very high-precisionmarking results. Two steel pins with a poin-ted tip for compass work and a rounded tipfor smooth scribing, pencil holder. Alumi-nium body with brass fittings, solid plasticcase. Instructions included.Max. opening 300 mm

B COMPASSES

1 Shaft length 150 mmOpening 160 mmNo. 707150 13.87 € 16.50 €Shaft length 200 mmOpening 215 mmNo. 707330 15.63 € 18.60 €

2 Shaft length 150 mm, with pencilholderOpening 160 mmNo. 707151 17.82 € 21.20 €Shaft length 200 mm, with pencil holderOpening 215 mmNo. 707331 20.34 € 24.20 €

Inspection and transferring instruments

Tongue length500 mm No. 717130 26.81 € 31.90 €

Tongue length500 mm No. 717133 26.81 € 31.90 € Circumference

Square

Cross-section

Measuring and inspection instruments || Inspection and transferring instruments

127

A JAPANESE MINI CARPENTER’SSQUARE

No. 707148 14.20 € 16.90 €

C GERMAN CARPENTER’S SQUAREThe standard square for every carpenteris made of stainless spring steel and hasa seamless cut. A deep-etched scale onboth sides of the square can be used forexternal and internal measuring. Theholes, spaced 5 mm apart, on the shortshank are used for parallel marking. Forthis technique the long shank works as afence and the oval-shaped holes centrethe pencil during pulling. Accuracy0.005 mm per 1 cm lengthThickness 1.2 mmWidth 35 mm800 x 320 mmNo. 707279 20.92 € 24.90 €

B ANGLE END STOPSTransforms your car-penter's square into atry square: the hexago-nal end stops made ofbrass are quickly andeasily fitted onto the carpenter’s squarewith knurled screws. The end stop facili-tates the repeated marking of bevels, e.g.in roofing beams. Leg thickness max. 6mm, 2-piece set.No. 708096 6.39 € 7.60 €

F CARPENTER’S TRY SQUARERosewood with brass fitting. Hardenedsteel tongue.275 x 155 mmNo. 707172 15.04 € 17.90 €

C

A

F

Seven angle positions (22.5°, 45°,67.5°, 90°, 112.5°, 135° and 157.5°)and high accuracy (+/- 0.06°). The hard-ened stainless steel blade latches intothe pressured ball bearing without freeplay and the try square fits any toolbag.Scale on both sides. Stainless steelblade, aluminium stock.Shaft length 135 / 160 / 185 mm

J ULMIA® PRECISION TRY SQUARE

D

J

B

G MINI TRY SQUAREWith a 45° mitre stop.105 x 68 mmNo. 707171 12.52 € 14.90 €

G

E JAPANESE TRY SQUAREHandy and accurate:Precision square with mm scale on bothsides, inner and outer dimensions. Sidedecorated with Japanese motives. Stain-less steel.150 x 100 mmNo. 717115 18.40 € 21.90 €

E

I SOLID STEEL TRY SQUARESmall precision square with a guaranteedaccuracy of 0.1 mm. Tool steel (notstainless).125 x 80 mmNo. 707245 9.16 € 10.90 €

I

H

H MINI TRY SQUARESSmall Japanese try square with stainlesssteel tongue and brass side, ground.Shaft length 38 / 40 / 65 mm

To check the squareness of a trysquare, make a mark line on a board,then turn the try square over andmake a second line. If the lines arenot identical then the angle betweenthem is twice the actual deviation.To correct this, you can use a scriberto scratch a line on the blade at halfthis angle and then use a fine file totrim the blade edge to this line.

K ULMIA® PRECISION MITRE GAUGEFor scribing mitres at angles of 45° and135°. Headpiece of rosewood with herr-ingboned brass edges, steel rail hardenedand blued. Fastened by double rivets toinlaid brass plates on both sides. Accuracy +/- 0.02 mmLength 350 mmNo. 707309 44.45 € 52.90 €

L VERITAS® SLIDING SQUAREInnovative:The carefully conceived sliding squareproves to be the ideal aid for scribinghinges, fittings and mortise joints. Thestainless steel plate is graduated alongthree sides. The right side of the bladecan be inscribed by users due to thematt finish. Slip-proof, light metal endstop with brass locking screw. Two dia-mond-shaped openings make parallelmarking easier. Measuring scale 0-100 mmNo. 703647 28.99 € 34.50 €

L

K

Stainless steel square for small workpie-ces and joints. Permanently etched onboth sides and both edges. Thickness 1 mmWidth 15 mm150 x 70 mm

D NOBEX® OCTO FOLDING SQUARE

Tongue length200 mm No. 707297 16.72 € 19.90 € 300 mm No. 707298 18.91 € 22.50 € 400 mm No. 707299 23.11 € 27.50 €

This square from Ulmia satisfies all therequirements of an optimum measuringtool. The handle is made of fine rose-wood with hand recesses and is pro-tected by two herringbone finished brassedges. The hardened steel blade is per-manently fixed by four rivets bound tobrass frames inlaid on both sides of thehandle. Accuracy +/- 0.02 mmShaft length 105 / 150 / 195 mmTongue length150 mm No. 707304 34.71 € 41.30 € 250 mm No. 707305 41.93 € 49.90 € 350 mm No. 707306 51.18 € 60.90 €

Tongue length45 mm No. 707274 8.32 € 9.90 € 60 mm No. 717120 8.32 € 9.90 € 100 mm No. 717121 8.32 € 9.90 €


128

K COMPACT COMBINATION SQUARE, 2-PIECE SETHandy measuring and marking tool, con-sisting of a 150 mm rule with slidable45°/ 90° square head. Chrome-platedmatt stainless steel rule. Grey cast ironheads, ground edges. Deep-etched mmand inch scales.No. 800159 19.24 € 22.90 €

A SHINWA® MITRE SQUARESPrecision square with Japanese ornamen-tation. Ground stop and edges. Stainless steel.

B SHINWA® 3-D MITRE SQUARETime-saving and precise:Can be used for marking 45° and 90°mitres on battens or counterbattens. Thissaves time and increases precision inmaking mitre joints or with cross-cuts.The fence also allows the tool to be usedfor scribing parallel lines. Made of ano-dised aluminium, with permanently et-ched scale markings.

1 45°/90° SquareFor mitres and cross-cuts.169 x 63 x 73 mmNo. 717122 15.88 € 18.90 €

2 45°/45° SquareFor marking pairs of mitres.200 x 63 x 73 mmNo. 717123 16.72 € 19.90 €

C VERITAS® DOVETAIL MARKERSPrecision tools formarking dovetails.Aluminium, black ano-dised, extra-longshank, relieved insidecorner. 40 x 50 x 65 mm

Dovetail ratio 1:6 (softwood)No. 703654 13.03 € 15.50 €

Dovetail ratio 1:8 (hardwood)No. 703655 13.03 € 15.50 €

Smart precision marker for laying out dovetail joints with two different slopesfor hardwood (1:7) and softwood (1:6).Brass plate with mortised cocobolo stock.Plate 45 x 45 mmHeight 32 mmNo. 707284 28.49 € 33.90 €

E DOVETAIL SQUARESRosewood body with brass fittings. Hardened steel blades 70 mm

Dovetail ratio 1:6 (softwood)No. 707173 14.20 € 16.90 €

Dovetail ratio 1:8 (hardwood)No. 707197 14.20 € 16.90 €

F DOVETAIL GAUGEFor marking straight and angled dovetailjoints, 1:8 ratio. Adjustable width (6 - 40 mm) and angle, stainless steel.Blade and shaft length 150 mmNo. 707179 19.24 € 22.90 €

G STARRETT® COMBINATION SQUARE,4-PIECE SETHigh precision:Versatile, precise measuring and markingtool, consisting of a 300 mm precisionrule which can be fitted with either acombination 45°/ 90° square head withintegrated spirit level, a locking pro-tractor or a centering head. Deep-etchedmm scale with ½ mm on reverse. Hard-ened stainless steel rule, grey cast ironheads coated with solvent-resistant, weatherproof wrinkle finish, precision-ground edges. Comes in plastic case.

H STARRETT® COMBINATION SQUARE,2-PIECE SETHardened stainless steel rule and slid-able 45°/ 90° square head, with spiritlevel. Deep-etched mm scale with ½ mmon reverse. Grey cast iron heads coatedwith solvent-resistant, weatherproof wrin-kle finish, precision-ground edges.

I COMBINATION SQUARE, 4-PIECE SETMulti-functional:300 mm rule which can be fitted witheither a combination 45°/ 90° squarehead, a locking protractor or a centeringhead. Deep-etched mm and inch scales.Chrome-plated matt stainless steel rule,grey cast iron heads, ground edges.

No. 707300 46.13 € 54.90 €Repl. rule No. 707302 14.20 € 16.90 €

J COMBINATION SQUARE, 2-PIECE SETrule and slidable 45°/ 90° square head.Deep-etched mm and inch scales. Chrome-plated matt stainless steel rule, grey castiron heads, ground edges.No. 707301 25.97 € 30.90 €

A BC D

F

I

1

2

1

2

J

E

G

H

K

1 No scale110 x 90 mm45°No. 717131 9.16 € 10.90 €

2 Deep-etched mm scale markings170 x 100 mm45°, 90°, 135°No. 717147 15.29 € 18.20 €

D VERITAS® DOVETAIL MARKERS

No. 718302 178.15 € 212.00 €

No. 718301 61.26 € 72.90 €


129

Sliding bevels and profile gauges

B VERITAS® BEVEL SETTERSet bevels faster:This is an ingenioustool for setting angleswhen lining up and formarking or measuringworkpieces. Piecescan be positionedfreely in line with the etched markings orwith the help of the fence. Special dovetail and polygon markings are on theback, as is a mm scale.75 x 180 mmNo. 703667 29.33 € 34.90 €

C VERITAS® SET, BEVEL SETTER ANDPRECISION SLIDING BEVELBevel: 165 mm x 250 mmBevel setter: 75 x 180 mm No. 703669 67.14 € 79.90 €

Price advantage

Rosewood with brass fittings. Hardenedsteel blade.150 x 230 mmNo. 707174 18.49 € 22.00 €

G SLIDING BEVEL, ROSEWOODBody made of rosewood with brass fitt-ings. Angles are fixed through an adjust-ment screw, which is not in the way likea lever when marking or transferring an-gles. Blued and hardened steel blade.150 x 230 mmNo. 707327 16.72 € 19.90 €

H MINI SLIDING BEVEL, ROSEWOODStainless steel blade.65 x 95 mmNo. 707176 10.84 € 12.90 €

A

B

D

E

F SHINWA® SLIDING BEVELSJapanese precision sliding bevels withaluminium body. Chrome-plated steelblade. The locking mechanism is positionedin the upper part of the body to prevent itfrom interfering during use.Shaft length 125 / 150 mm

D ULMIA® PRECISION SLIDING BEVELFor measuring, transferring and scribingangles. Body made of rosewood, endsprotected by inlaid riveted brass plates.Simple locking of the hardened bluedsteel blade via large wingnuts.Shaft length 250 / 330 mm

A VERITAS® PRECISION SLIDING BEVELSPrecision sliding bevels with one-handedblade locking, integrated flush in thestop. Handle made of warp-free, epoxy-saturated hardwood, stainless steelblade.Shaft length 90 / 165 mm

G

I PROFILE GAUGES WITH STAINLESSSTEEL PINSWith fine stainless steel pins for particularly accurate results.Needle Ø of 0.75 mm. Specified in mm.Depth 50 mm, length 150 mmNo. 707167 11.68 € 13.90 €

Depth 105 mm, length 300 mmNo. 717142 41.09 € 48.90 €

I

J PROFILE GAUGES WITH PLASTICBLADESFor measuring and transferring profiles.No offset, as blades are flush with theframe.Depth 40 mmBlade thickness 1.3 mm

Length1 125 mm No. 707145 8.91 € 10.60 € 2 255 mm No. 707147 14.71 € 17.50 € Extension for both lengths

125 mm No. 707146 8.91 € 10.60 €

Flatness inspection

K PRECISION KNIFE EDGE SQUARESFor checking the squareness of an edge,using the light-gap method. The blade isbevelled on both sides. Blade cross-section 18 x 5.5 mm, stainless steel. Accuracy grade 00 in accordance with DIN 875, squareness tolerance of 0.004 mm, comes in a protective case.Shaft length 70 / 130 mm

L PRECISION KNIFE EDGE RULESHighest precision:

Length100 mm No. 707290 11.34 € 13.50 €300 mm No. 707291 28.49 € 33.90 €500 mm No. 707292 55.38 € 65.90 €

H

F

J

1

2

K

L

C

Tongue length100 mm No. 707229 41.93 € 49.90 € 250 mm No. 707230 46.13 € 54.90 €


E ENGLISH SLIDING BEVEL


Profile gauges

Create a positive and negative imageof any profile by pressing. The ease ofuse is only surpassed by the widerange of possible applications. Restor-ers and turners can use this for copy-ing profiles, floor layers can use it forfitting work, boat builders and violinmakers can use it for checkingarches.


The best way of checking if asurface is flat is with thisstraight edge, using the light-gap method. The rules are bev-elled on the measurement edgeand have a textured rubbergrip. Stainless steel, accuracygrade 00 in accordance withDIN 874, comes in a protectivecase.Tolerance 0.002-0.004 mmThickness approx. 8 mm


130

Inclination measuring tools and moisture meter

The extremely torsion-resistant 4-cham-ber aluminium profile and two shock-ab-sorbing rubber end caps make this spiritlevel the ideal tool on site. Two verticalblock vials and one horizontal vial withmagnifying effect, as well as milled mea-suring surfaces ensure extreme accuracyon all surfaces.

1 Length 60 cm600 x 60 x 27 mm640 gNo. 707295 50.34 € 59.90 €


The hefty 1.8 mm thick aluminium profilemakes this spirit level a torsion-resistantlightweight. A horizontal and a verticalvial, both also visible from the top, ensureaccuracy in any measuring situation. Themagnifying effect of both vials allows easyreading, while a rubber end cap protectsthe spirit level from damage.



C SPIRIT LEVEL, ROSEWOODFine, compact spirit level in the traditional»torpedo« form. Rosewood with brass fit-tings.230 x 19 x 38 mmNo. 707177 21.76 € 25.90 €

D SHINWA® LINE SPIRIT LEVELYou can use this ultra-light spirit level tocheck whether a tensioned line guide islevel or not. The spirit level is hung on theline by the two eyelets for this. It can alsobe used as a normal surface spirit level.Length 100 mm15 gNo. 707226 9.16 € 10.90 €

E GRADOMETERCompact Japanese level for accuratelymeasuring oblique or inclination angles,e.g. in carpentry, interior extensions orplumbing. Rotating bubble level withangle, graduated and inclination scale,0° to 90°, accuracy: +/- 1°. Aluminium,V-shaped groove (for pipes, etc.), rubberimpact protection.Length 100 mmNo. 717158 18.40 € 21.90 €

F ACRYLIC MEASURING TOOLS Compact and light measuring tools of un-breakable acrylic glass. Their crystallineappearance is not only elegant but alsomakes handling easier. The high level ofmanufacturing precision means that ei-ther side can be used for reference.

1 Mini levelWith two vials, for checking the horizon-tality, verticality or squareness. Accurateto within 0.14°.15 x 25 x 75 mmNo. 717151 14.71 € 17.50 €

2 Card levelA credit-card size, 6 mm thick spiritlevel, with a 45°/60°/90° display as wellas a deviation indicator (1/100 and2/100).54 x 86 mmNo. 717155 10.34 € 12.30 €

G BRASS PLUMB LINEPlumb bob of varnished brass with nut tofasten the string and replaceable tip ofhardened steel. The 3 m braided polya-mide string is tearproof and weather-re-sistant and is cut hot to preventfrazzling. Replacement tip included.135 x 75 x 50 mmString length 3 mNo. 707286 14.20 € 16.90 €

H MOISTURE METERNothing is more irritating than the dryingcracks or heavy warping that can occurafter working on wood that is too wet.This moisture meter provides assistancewith two different measuring modes: search mode provides non-destructivemeasurement to a depth of 5 cm, needlemode measures to a depth of 1.2 cm.Also suitable for concrete. Measuringrange of 0-80%. Sturdy professional quality in a plastic case with wood table.No. 707285 205.04 € 244.00 €

A

D

E

1

G

H

B

C

F

2

1

2

1

2

A BMI® ROBUST SPIRIT LEVEL

B BMI® ULTRASONIC SPIRIT LEVEL

BMI spirit levels- Select, high-quality materials- High measuring accuracy (0.5 mm/m

in normal positions and when measuring overhead)

- Up to 30 years warranty from BMI on the service life of the vials

- Ultrasonically welded vials with non-glare reading

Measuring and inspection instruments || Surveying tools

131

Surveying tools

Optical survey

B FLEX LIGHT® WITH MIRRORInspection light with flexible shaft for illuminating confined spaces, jointedmirror attachment and bright Kryptonbulb. Runs on three 1.5 V AA batteries(not included).Overall length 620 mmShaft length 430 mmHead Ø 8.5 mmNo. 708019 23.45 € 27.90 €Repl. bulb No. 708017 3.11 € 3.70 €

A BEND-A-LIGHT® MINIFor illuminating confined spaces and inspecting hollow areas. Flexible, brass-plated wire shaft with plastic housingand protective sleeve. Runs on two 1.5 V AA batteries (not included).Overall length 400 mmShaft length 250 mmHead Ø 5 mmNo. 708001 27.65 € 32.90 €Repl. bulb No. 708002 7.31 € 8.70 €

F ILLUMINATED MAGNIFYING GLASSFree-standing illuminated magnifyingglass can be used for inspecting holesand cracks in musical instruments andantiques as well as jewellery, miniatures,stamps, etc. 15x magnification, opticalglass lens, bright LED bulb with 40,000hours lifetime. Plastic housing. Batteries(3 x 1.5 V AAA) not included. Comes in case.110 x 37 x 25mmLens Ø 21 mmNo. 708015 19.75 € 23.50 €

G SHINWA®

MULTIPLE MAGNIFYING LENSCompact pocket magnifying glass withthree lenses. Individually they provide 3 x, 4 x or 5 x magnification and a maximum of 12 x magnification whenused in combination. The aluminiumlens frames can be folded into the steelcase and a chromed chain helps keep the magnifying glass handy.Lens Ø 19 mmNo. 707999 25.63 € 30.50 €

D TELESCOPIC MIRROR

No. 707112 11.93 € 14.20 €

E LARGE INSPECTION MIRROR

No. 707109 11.93 € 14.20 €

BA

F

G

E

C INSPECTION MIRRORS

Length1 170 mm No. 707113 6.13 € 7.30 €Repl. mirror No. 707115 3.53 € 4.20 €2 225 mm No. 707111 10.00 € 11.90 €Repl. mirror No. 707100 4.96 € 5.90 €

H RETRIEVERFor grasping and hold-ing hard-to-reach ob-jects (stringed instrument sound posts,etc). Flexible shaft made from corrugatedhose (retains its position once bent).With three claws.Length 500 mmMount approx. 16 mmGripper head Ø 9 mmNo. 717190 19.24 € 22.90 €

I MAGNETIC PICKUP, EXTRA STRENGHExtra-strength tool for retrieving screwsor other ferromagnetic objects from narr-ow recesses and hollows – retractableand with pocket clip.Max. length 600 mmLifting power approx. 1500 gTip Ø 11 mmNo. 707119 7.56 € 9.00 €

Retrievers, pickups and tweezers

2 round tipBentLength 110 mmNo. 707142 3.78 € 4.50 €

1 pointed tipSlightly curved, slim.Length 110 mmNo. 707141 3.78 € 4.50 €

K TWEEZERS, 6-PIECE SETHigh-quality tweezers for technical applications.Pointed 120 mm, 150 mm and 180 mmBent 175 mmFlat with sliding lock 165 mmReverse action (self-locking) 165 mmNo. 707143 8.32 € 9.90 €

L HOOKS AND PICKS, 6-PIECE SETStainless steel dental picks and hookswith fine needle-point tips for picking up,adjusting, marking or cleaning small ob-jects.Length 130-160 mmNo. 700431 11.43 € 13.60 €

KL

1

2

J

D

1 2

C

H

I

For inspecting hollow bodies and posi-tions that are difficult to access. 170 mmversion with flexiblemirror shaft, bendableinto any position, lowmagnification.Mirror Ø 24 / 30 mm

Double ball-jointed mirror with telescopichandle, slight magnification. Fits into anyshirt pocket thanks to its compact length.Length 195-690 mm (telescopic)Mirror Ø 30 mm

Particularly large inspection mirror withtelescopic shaft. Ball joint allows swivell-ing in any position.Length 275-380 mmJoint Ø 11 mmMirror Ø 55 mm

J TWEEZERSPrecision tweezers, stainless steel.

Measuring and inspection instruments || Workshop knives

132

Workshop knives

Marking and veneer knives

A TASAI KOGATANAThe exquisite TasaiKogatana are made in a Japanese masterforge in small series. The knives, whichare mainly used for scribing by cabinet-makers and carpenters, stand out due tothe attractive surface of the hand-forgedDamascus steel. Including a kiriwoodcase, with the signatureand seal of the black-smith. Right bevel.Blade width 21 mmOverall length 215 mmNo. 719291 284.87 € 339.00 €

B KOGATANA DELUXE

Blade width3 mm No. 710505 33.53 € 39.90 €6 mm No. 710504 33.53 € 39.90 €8 mm No. 710503 33.53 € 39.90 €10 mm No. 710507 33.53 € 39.90 €12 mm No. 710502 33.53 € 39.90 €15 mm No. 710506 33.53 € 39.90 €18 mm No. 710501 41.09 € 48.90 €

C KOGATANA STANDARD

Double bevelBlade width3 mm No. 710205 10.59 € 12.60 €6 mm No. 710204 10.59 € 12.60 €8 mm No. 710203 10.59 € 12.60 €10 mm No. 710207 10.59 € 12.60 €12 mm No. 710202 10.59 € 12.60 €15 mm No. 710206 10.59 € 12.60 €18 mm No. 710201 10.84 € 12.90 €

Left bevelBlade width6 mm No. 710304 13.36 € 15.90 €10 mm No. 710307 13.36 € 15.90 €12 mm No. 710302 13.36 € 15.90 €18 mm No. 710301 14.45 € 17.20 €

Right bevelBlade width3 mm No. 710405 10.59 € 12.60 €6 mm No. 710404 10.59 € 12.60 €10 mm No. 710407 10.59 € 12.60 €12 mm No. 710402 10.59 € 12.60 €15 mm No. 710406 10.59 € 12.60 €18 mm No. 710401 11.26 € 13.40 €

D SUMINAGASHI KOGATANAMulti-layered steel blade, handle andsheath of Japanese cherry wood with acoral inlay. Right bevel.Blade width 23 mmBlade length 90 mmOverall length 190 mmNo. 710706 74.54 € 88.70 €

E YOKOTE KOGATANADouble-layered steel blade with hammeredsurface. Right bevel.

1 With handle and sheathMagnolia wood.Blade width 20 mmBlade length 75 mmOverall length 160 mmNo. 710708 14.20 € 16.90 €

2 Blade without handleBlade width 20 mmOverall length 180 mmNo. 710709 12.27 € 14.60 €

F VENEER KNIFE (KIRIDASHI)Hand-forged slim knives made of double-layered steel with embossed surface andrattan binding. Right bevel.Overall length 200 mmBlade width9 mm No. 710530 26.81 € 31.90 € 15 mm No. 710531 30.50 € 36.30 €

G CARVING AND VENEER KNIVESExtra-strong blade of high-grade surgicalsteel XC 100 (stainless, approx. 62 HRC),pre-sharpened. The handle scales of polished Makassar ebony are fastenedwith sturdy brass rivets.Blade width 24 mmBlade length 70 mmOverall length 180 mmBevelDouble No. 700411 19.33 € 23.00 € Right No. 700412 19.33 € 23.00 € Left No. 700413 19.33 € 23.00 €

I PFEIL® SCRIBER KNIFEThe prism-shaped blade of this knife all-ows scribing to the left and right of a ruleor square. This makes it suitable for loca-tions that are difficult to access andequally useful for both left- and righthan-ders. Handle of oiled native cherry wood.Replacement needles are available.Width 18 mmOverall length 180 mmNo. 717113 11.68 € 13.90 €

J PURFLING CUTTERFor marking parallel lines and cutting aprecise groove for inlay strips. Two parallelblades of two-layer steel.Width 2.5-12 mmOverall length 145 mmNo. 717110 33.53 € 39.90 €

H MARKING KNIFEFor precise scribing. Japanese two-layersteel, ground on the right-hand side.Width 15 mmOverall length 170 mmNo. 717111 9.75 € 11.60 €

L SCALPEL BLADESSets of 12.

Blade1 Form A No. 700421 4.96 € 5.90 € 2 Form B No. 700423 4.96 € 5.90 € 3 Form C No. 700425 4.96 € 5.90 € 4 Form D No. 700427 4.96 € 5.90 € 5 Form E No. 700429 4.96 € 5.90 €

M JAPANESE CUTTERJapanese multi-purpose knife made ofstainless steel, for wood, paper, plastic, etc.Sharpened ready for use (resharpenable).Blade length 60 mmHandle length 115 mmNo. 710535 8.15 € 9.70 €

Cult tools:

N BESSEY® FOLDING KNIVESWITH CUTTER BLADES

The high-grade spring-loaded folding mecha-nism that’s free ofplay, the quick blade-release, the ergonomi-cally shaped handlewith belt clip and the distinctive app-earance are the hallmarks of this knife,which can be used for cutting wood, ven-eer, cardboard, leather, plastic and floor-ing materials.

1 Folding knife with plastic handleLight, comfortable to holdhandle scales with integratedreserve-blade compartment(for 8 blades) and a thumbpress on the spine for increased pressure.Overall length 160 mm130 gNo. 710540 15.71 € 18.70 €10 blades No. 710542 4.12 € 4.90 €

2 Folding knife with wooden handleHandle scales of fine laminatedwood. Riveted five times andpolished. No reserve-blade compartment.Overall length 150 mm175 gNo. 710541 14.87 € 17.70 €10 blades No. 710542 4.12 € 4.90 €

O JAPANESE CRAFT KNIVES

1 Curved edgeFor universal use.No. 709045 10.84 € 12.90 €

2 Straight edgeFor precision cuts, carving, pruning andskinning.No. 709046 10.50 € 12.50 €

Finely ground, sintered carbide cutterwith unsurpassed lifetime means effort-less glas cutting. Permanent lubricationthanks to petroleum reservoir in handle.Head width 14 mmLength 160 mmNo. 716155 27.14 € 32.30 €

L

1 2 3 4 5

Scalpels and craft knives

K SCALPELFor precision cuts in wood, paper, plasticand technical applications. Surgical scalpelwith solid stainless steel handle and secure blade-locking mechanism. 0.4 mmthin, extremely sharp blades of hardenedXC 100 stainless steel. Handle only (without blade).Handle length 160 mmNo. 700415 13.36 € 15.90 €

Japanese marking and inlay knivesThese hand-forged blades made ofmulti-layered steel are exceptionallysharp, wear-resistant and easy to resharpen.

The double-bevel knives are for all-purpose use. The single-bevel knivesare for making cuts along a straight

edge and for cutting perpendicularedges. Ideal for inlay and veneer work.

You can find Kogatana with a singlebevel and slight hollowing on the unbe-velled side at www.more-than-tools.de

The blades are hardened along theirentire length (58 HRC or 64 HRC). We recommend binding the handles,(e.g. with a leather band No. 709070or with rattan No. 708899).

Right bevel Left bevel

N

A

B

C

D

E

1

2

F

G

I

J

H

K

M

1

2

O

1

2

P

These hand-forged knives made of foldedSuminagashi steel (20 - 30 layers) arenotable for their exceptional edge life,even when working with exotic hard-woods. Double bevel.Overall length 160-180 mmBlade thickness 2-3 mm

3-layer steel. Overall length 160-180 mmBlade thickness 2-3 mm A sturdy craft knife does not necessarily

need to be expensive. This JapaneseMantaro craft knife is a great example ofthis. The 3 mm thick blade of easy-to-sharpen carbon-steel (SK5*) is mountedin a sturdy steel housing with a strong re-tention spring. The generously dimen-sioned, natural bubinga wood handlescales provide a secure grip even underthe toughest use. A stop prevents theblade from being damaged when closingthe knife. This knife is an essential itemfor every workshop and offers reliabilityand longevity in outdoor activities.* Hardness approx. 58 HRC, not rustproof.Blade length 70 mmOverall length 195 mmBlade thickness 3 mm125 g

P JAPANESE PROFESSIONAL GLASS CUTTER

Binding together!

Solid steel bar clamps and cast iron screw clamps | 134

C-clamps and edge clamps | 134

One-hand clamps | 135

Edge-protecting clamps | 136

Mitre clamps | 137

I-beam bar clamps and clamp fixtures | 137

Clamps for floor layers | 138

Tape tensioner | 138

Clamps

133

No. 705721 8.32 € 9.90 €

No. 705793 11.68 € 13.90 €

Attachment for securing edging, trim, veneers, etc. Can beused with most stan-dard screw clampswith a maximum barthickness of 12 mm.Spindle length 75 mm

No. 705943 14.03 € 16.70 €

Clamps || Solid steel bar clamps and cast iron screw clamps, C-clamps and edge clamps

134

C-clamps and edge clamps

D C-CLAMPSCompact, heavy-duty clamp with roundframe for applying concentrated press-ure. Forged-steel frame, zinc-plated; swivel pad.Jaw opening 17 mmJaw depth 20 mm41 gNo. 705910 4.12 € 4.90 €

Jaw depth Jaw opening1 50 mm 50 mm No. 705640 17.56 € 20.90 €

75 mm No. 705641 20.92 € 24.90 €2 60 mm 100 mm No. 705642 26.64 € 31.70 €

F MINI SCREW CLAMPS, 3-PIECE SETAluminium bar with foot, steel screws,plastic pads, simple design.3-piece set. 23 x 32 mm, 35 g 30 x 43 mm, 46 g 37 x 56 mm, 62 g

E EDGE CLAMPSolid 3-way clamp for gluing edges and otherrectangular joints. Forged steel clamp arm,zinc-plated.Jaw opening 65 x 65 mm580 g

G BESSEY® EDGE CLAMP DEVICE

D

E

Solid steel bar clamps and castiron screw clamps

Jaw depth Jaw opening1 50 mm 100 mm No. 705632 7.98 € 9.50 €

300 mm No. 705633 10.84 € 12.90 €2 60 mm 120 mm No. 705634 10.00 € 11.90 €3 80 mm 160 mm No. 705635 13.03 € 15.50 €4 100 mm 200 mm No. 705636 17.56 € 20.90 €5 120 mm 250 mm No. 705637 20.92 € 24.90 €

500 mm No. 705638 32.69 € 38.90 €1000 mm No. 705639 47.82 € 56.90 €

B BESSEY® MALLEABLE CAST IRONSCREW CLAMPSUnbending:This clamp stays rigid, even at a hightightening torque, and does not slacken.The robust, hardened, hollow profile barwith ribbing and corrugated malleablecast-iron clamp arms are designed forclamping for up to 600 kp. A set screwin the sliding arm, which grips into theribbing of the bar, offers maximum secu-rity against loosening and slippage. Ball-jointed swivel pad, strong trapezoidthread, beechwood handle.

Jaw depth Jaw opening1 50 mm 100 mm No. 705713 11.51 € 13.70 €2 100 mm 200 mm No. 705714 24.87 € 29.60 €3 120 mm 500 mm No. 705715 39.41 € 46.90 €4 120 mm 1000 mm No. 705716 50.34 € 59.90 € No. 705790 5.80 € 6.90 €

B

A

F

G

H

2

1

C

1

2

3

4

5

A SOLID STEEL BAR CLAMPSThe manufacturer of industrial weldingclamps also applies their experience andthe same materials to these multi-purposesolid-steel clamps. Thanks to the all-steelarms, these clamps are designed for flex-ible, elastic clamping (metal and wood)and guarantee high strength at a lowweight. The galvanised fixed arm and theclamping pad are forged from a singlepiece. The burnished trapezoidal spindleruns precisely in the guide and allowsdelicate clamping. Ball-jointed clampingpad. Wooden handle.

1. Rigid clamping, e.g. malleable cast-iron clamps:With rigid clamping you can achievestrong clamping forces, making thistype of clamping preferable for gluedwoodjoints.

2. Flexible clamping,e.g. all-steel clamps:Thanks to the flexible fixed and sliding

arms, the clamping force is much lessaffected by vibrations than with rigidmalleable cast-iron clamps, so theworkpiece is held more firmly in place.Flexible clamping is often used whenclamping and fixing wood and metalparts in order to work on them, or forclamping workpieces to machine partsthat are subject to vibrations.

C BESSEY® PROTECTIVE STRIPSTo protect the surface of the clamped ob-ject from damage. 2 units, can be cut tosize, suitable for No. 705713-705716.

H C-CLAMPSThese clamps are made of a special alloysteel and achieve the highest clampingforces thanks to their C-shaped forgedarm. The burnished spindle with tommybar turns smoothly and precisely. Steelarm with nickel plating, ball-jointedclamping pad.

For more clamps (such as Bessey®)see our webshop at www.more-than-tools.de

No. 705789 8.24 € 9.80 €

No. 735754 122.69 € 146.00 €

Clamps || C-clamps and edge clamps, One-hand clamps

135

A HERDIM® REPAIR CLAMPSLightweight, precision clamps for repairing musical instruments and otherfine handcrafted objects. Forged-steelframe with galvanised surfaces. Fast-action brass screw with ball-jointed swivel pad and knurled knob.

Jaw depth Jaw opening Weight (g)1 22 mm 12 mm 11 g No. 735719 15.04 € 17.90 € 2 27 mm 15 mm 18 g No. 735718 16.39 € 19.50 € 3 40 mm 30 mm 35 g No. 735714 16.72 € 19.90 € 4 90 mm 30 mm 75 g No. 735715 18.07 € 21.50 € 5 85 mm 40 mm 115 g No. 735702 21.51 € 25.60 € 6 135 mm 40 mm 170 g No. 735704 22.61 € 26.90 € 7 205 mm 40 mm 300 g No. 735707 26.81 € 31.90 € 8 50 mm 80 mm 105 g No. 735709 24.20 € 28.80 € 9 150 mm 80 mm 205 g No. 735711 29.75 € 35.40 € 10 300 mm 80 mm 720 g No. 735713 35.63 € 42.40 €

7-piece setNo. 735702/04/07/14/15/18/19.

Price advantage

One-hand clamps

The advanced version of the all-steelclamp for fast, vibration-resistant clam-ping, thanks to a plastic-coated, non-slipratchet-type lever. Galvanised fixed armand clamping pad forged from a singlepiece. Precisely made, wear-resistantcatch mechanism for controlled clampingforce.Jaw depth 100 / 140 mmJaw opening200 mm No. 705630 30.17 € 35.90 €300 mm No. 705631 46.13 € 54.90 €

C BESSEY® KLIKLAMPPreserves your workpiece:The clamp arms of ultra-light magnesiumcan be quickly set to the exact amount of clamping pressure desired using the ratchet lever. Their exceptionally lightweight and protective clamping surfacesmake them especially well-suited for de-licate workpieces and assembly work.Galvanised steel bar.Jaw depth 80 mmJaw opening200 mm No. 705792 17.73 € 21.10 €

D ONE-HAND SPREADER CLAMPS®

Jaw opening150 mm No. 705771 11.68 € 13.90 € 300 mm No. 705772 13.87 € 16.50 € 600 mm No. 705774 16.72 € 19.90 €

3-piece setSet includes No. 705771, 705772, 705774.No. 705770 37.82 € 45.00 €

Price advantage

D

The ideal clamp for lightweight objectsthat need to be bonded quickly. Preferred in model construction and instrument making. Adjustable with onehand, rubber-coated jaws, quick release. Max. opening 110 mmJaw depth 30 mm50 g

C

E

Spreading mode

A

1 2 3 4 5 6 7

8 9 10

B QUICK-LEVER CLAMPS

B

Spreader clamps can be easily attached,virtually free-of-play, and can be ten-sioned with one hand by means of a pistolhandle with ratchet function. Large-areajaws with soft plastic protectors preservethe workpiece and ensure even clampingpressure through the one-sided ball-headmounting. By reversing the feet, theclamp can also be used for spreading.Break-proof fibreglass-reinforcedpolyamide arms, bar of hardened steel.Jaw depth 85 mm.

E MICRO TRIGGER CLAMP

No. 705875 24.37 € 29.00 €

No. 705919 3.28 € 3.90 €

No. 705869 4.54 € 5.40 €

Clamps || One-hand clamps, Edge-protecting clamps

136

A GORILLA CLAMPS®

These inexpensive gluing clamps guaran-tee powerful clamping pressure, yet areextremely lightweight. Their swivel jawsadjust to the contours of the workpiece,while their fibre-reinforced arms with-stand heavy-duty use.

Jaw depth1 30 mm No. 705866 1.43 € 1.70 € 2 50 mm No. 705867 1.60 € 1.90 € 3 80 mm No. 705868 2.10 € 2.50 €

3-piece setNo. 705866-868.

Price advantage

C POWER CLAMPS®

Controlled clamping pressure:Lightning-quick, easy-to-use and preci-sely adjustable clamping pressure. Theself-locking mechanism maintains theexact amount of pressure until the clampis released by the stop lever. Ideal for veneering, assembly work and making repairs. Swivel clamping pads made ofsoft plastic, break-resistant fibreglass-reinforced plastic arms.

Jaw opening 50 mmJaw depth 55 mm140 gNo. 705670 8.07 € 9.60 €

Jaw opening 100 mmJaw depth 75 mm265 gNo. 705672 9.58 € 11.40 €

B VARIO SPRING CLAMPThese spring clamps have a particularlywide range of applications, because thespring power can be easily set from 0.5 kg to 25 kg with a Phillips-headscrew. Movable soft jaws adjust to theworkpiece and avoid dents. Handlesmade of fibreglass-reinforced plastic.Jaw depth 40 mmMax. opening 25 mm90 g

A

Edge-protecting clamps

D KLEMMSIA® CLAMPSThe original from Germany:Light, fast-acting clamps. The clampingpressure can be regulated via a camlever. Cork pads protect the surface ofthe workpiece. One movable clamp arm.Zinc-plated steel bar with hornbeam jaws.

Jaw depth Jaw opening Weight (g)110 mm 200 mm 440 g No. 705810 8.32 € 9.90 €

400 mm 610 g No. 705823 9.92 € 11.80 € 600 mm 780 g No. 705812 11.60 € 13.80 € 800 mm 915 g No. 705824 13.28 € 15.80 €

150 mm 200 mm 500 g No. 705825 12.52 € 14.90 € 200 mm 200 mm 530 g No. 705811 13.36 € 15.90 €

G PARALLEL CLAMPSThe wooden jaws of these practicalclamps can close at a variety of angles.Clamping pressure is distributed evenlywithout torsion. Screws made of galvani-sed steel, jaws and handles of maple.

Jaw length Jaw opening Weight (g)100 mm 55 mm 180 g No. 705871 4.62 € 5.50 € 150 mm 75 mm 410 g No. 705872 5.80 € 6.90 € 200 mm 115 mm 850 g No. 705873 7.48 € 8.90 € 255 mm 150 mm 1080 g No. 705874 9.16 € 10.90 €

4-piece setNo. 705871-874.

Price advantage

Tip:To quickly open para-llel clamps, hold thehandles with bothhands and turn themas you would a crank.

D

F JAPANESE CLAMPS (HATAGANE)Slender brass clamps with parallel clamping pads for gluing delicate materials and for marking and cuttinglatticework and frames, etc.

Jaw depth Jaw opening Weight (g)12 mm 955 mm 45 g No. 713201 8.32 € 9.90 €

155 mm 90 g No. 713203 8.82 € 10.50 € 15 mm 270 mm 105 g No. 713205 10.76 € 12.80 €

H BESSEY® BODY CLAMPSThe exactly parallel clamping faces makethe body clamp the ideal tool for assemb-ling furniture corpuses. With the extra-large contact surfaces, even sensitiveworkpieces can be clamped without fur-ther supports. Workpiece supports fittedon the bar prevent direct contact with theworkpiece and produce exact rectangula-rity. No tools are needed for reversing thelower arm, so that this clamp can also beused as a spreader.Jaw depth 95 mmJaw opening800 mm No. 705717 53.70 € 63.90 € 1250 mm No. 705718 66.97 € 79.70 €

1

2

3

B

C

1 2

E F

G

HJaw depth Jaw opening Weight (g)110 mm 1200 mm 1265 g No. 705818 17.90 € 21.30 €

E KLEMMSIA® CLAMP, BOTH CLAMPARMS MOVABLEOtherwise, specification as above.

No. 705769 60.50 € 72.00 €

15 mm 15-25 mm No. 705742 2.44 € 2.90 €30 mm 25-35 mm No. 705743 2.61 € 3.10 €45 mm 35-50 mm No. 705744 2.61 € 3.10 €55 mm 40-65 mm No. 705745 2.61 € 3.10 €No. 705746 1.60 € 1.90 €

Clamps || Mitre clamps, I-beam bar clamps and clamp fixtures

137

Mitre clamps

E PRECISION MITRE CLAMP

A SPRING MITRE BRACKET SET

No. 705741 14.20 € 16.90 €

C REPLACEMENT BRACKETS, 4 UNITSFits Spring Mitre Bracket Set No. 705741.

B PROTECTIVE COVERS, 4 UNITSFits Spring Mitre Bracket Set No. 705741.

A

E

B

D

No. 705909 13.87 € 16.50 €

No. 705944 22.27 € 26.50 €

No. 705954 19.75 € 23.50 €

I-beam bar clamps and clamp fixtures

H ALUMINIUM BAR CLAMPS

Jaw opening Weight (g)610 mm 1050 g No. 705940 40.25 € 47.90 €910 mm 1400 g No. 705941 44.45 € 52.90 €1220 mm 1800 g No. 705942 50.34 € 59.90 €

1 Pony® No. 50

2 Pony® No. 56Reversible heads for use as a spreader, winged-screw 2-piece set, head and tailcastings (without pipe).Jaw depth 62 mm

G PONY® CLAMP SADDLES,4-PIECE SETFor making a variety of clamping jigs.Aluminium, with fixing screw and mounting hole. 4-piece set.

F

1

2

G

H

C

Lightweight spring brackets for quick andeasy assembly of frames and other woodenconstructions. Only one hand is requiredto operate the mitre pliers, so the otherhand remains free for the workpiece. Pro-tective covers can be applied to the poin-ted ends when working with sensitivesurfaces. Brackets ofhardened spring steel.Set includes 4 clamps.Distance betweenpoints: 55 mm,For moulding width: 40-65 mm

D MITRE CLAMPFor working and gluing frames and profiles. Base plate with two boreholesfor fastening to the worktop. Cast-iron,precisely milled 90° workpiece fitting.Jaw opening 100 mm3000 gNo. 705936 43.70 € 52.00 €

Heavy-duty vice for precise rectangularjointing, working and gluing frames andother profiles. The vice can be turned360° on its base, angled up to 90° andlocked into every position. The centralsaw slot allows work to be done while thepiece is clamped in position. Four holesin the base for securing the vice to a workbench. Made of cast iron.Jaw opening 100 mm4800 g

F PONY® CLAMP FIXTURESLength according to need:Gluing clamps of optional length bymounting onto any 3/4” standard pipe(outer Ø 26 mm) with threaded ends.The tail has a quick-release clutch forrapid adjustment. Spindle travel 50 mm.

Crank handleJaw height 42 mm

These extremely lightweight aluminiumgluing clamps offer high tensile strengthand will not cause glue to stain uponcontact. Screw, tail and headpieces madeof steel. The bar features notches in 25 mm increments for quick adjustment.

Load capacity max. 750 kpBar cross-section 20 x 40 mmJaw height 42 mm

Distance be- For mouldingtween points width

No. 705710 40.17 € 47.80 €

No. 703200 108.32 € 128.90 €

No. 705827 80.59 € 95.90 €

No. 705950 20.92 € 24.90 €

Clamps || I-beam bar clamps and clamp fixtures , Clamps for floor layers, Tape tensioner

138

A CLAMP FIXTURESRobust quality at a low price:

B HEAVY DUTY I-BEAM BAR CLAMP

Clamps for floor layers

C FLOORING CLAMPIdeal for joining and pressing solid woodfloorboards when laying on floor battens.High pressure through cogwheel withslotted head handle. Self-locking clam-ping jaws for quick attachment andtightening. Also well suited for gluing panels.Overall length 175 mmJaw opening (width ofthe battens) 30-80 mmSpindle length 85 mm6.5 kg

D PARQUET CLAMPIf you want to lay parquet or floorboardswithout visible joins, our parquet clampis the right tool for you. It consists of tworobust angle profiles. One is attached tothe already fixed board, while the other isequipped with a ratchet mechanism,which is tightened with its 4.2 m tape oftear-resistant polyester (25 x 1 mm) tothe board to be laid.137 x 120 mmNo. 705828 26.81 € 31.90 €

Tape tensioner

Multi-angular structures, cylinders and irregular workpieces are very difficult toglue using clamps; these usually requirecomplex support structures. In suchcases you are better served with a tapetensioner: You place the tape, made oftear-resistant polyester, around the work-piece and tension it seamlessly. The se-cond application for this tool is in thegluing of frames cut to mitre. The foursupplied Vario angles for angles of 60° to180° exert even pressure on the mitrejoints and also ensure the necessary separation distance fromthe workpiece.Tensioning scope max. 7 m with integrated roll up mechanism.

F MULTI CLIPBonding, pressing and securing:

No. 705870 2.69 € 3.20 €

A

B

C

D

E

F

Heavy-duty clamp fixtures for mountingon any board or square bar up to 25 mmin thickness. Swivel pad. 2-piece set:head and tail castings.Spindle length 110 mmHeight 40 mm

Sometimes you need a pressure reserve,e.g. when gluing door frames, staircases orthick panels. With its rigid I-profile, power-ful trapezoid thread and robust hand crank,this door clamp is a match for the mostdifficult challenges.I-profile 85 x 45 x 4 mmJaw opening 1200 mmJaws 55 x 85 mmSpindle length 150 mm14.5 kg

E BESSEY® TAPE TENSIONER WITH VARIO CORNER PADS

Patented traction clamp for securingwooden parts for assembly or gluing,bundling cables, rods or wires, securingladders, posts or pipes, etc.

Two or more clamps can be combined toaccommodate larger objects. Made ofhigh-strength glue-repellent plastic.Jaw opening Ø 12-100 mmClamping force max. 100 kp17 g

139

Drilling tools | 141

Drill chucking tools | 141

Bit chucking heads and bits | 142

Wood and metal drills | 142

Countersinks and countersink drills | 144

Cylindrical and tapered cutters | 144

Circle cutters and threading tools | 146

Screwdrivers | 146

Pliers | 147

Drills, pliers,screwdriversTrust them for reliability and precision!

Drills, pliers, screwdrivers

140

TYPES:

Twist augers

Twist augers are the classic wood drills,

which when properly used produce clean,

precise and straight holes. They have a

screw tip that is drawn into the wood by

itself. Hand -driven augers have a tip with

a steep-angle thread, and machine-driven

augers a flat thread. A deep flute for chips

helps clear the boring chips. One or two

spurs separate the fibres, and the wood is

then peeled away by the horizontally positio-

ned cutting lip. The tool-steel augers are

designed for low rotational speeds and soft

to moderately hard types of wood.

Brad point drills

These are the most widely used machine-

driven wood drills. The brad-point tip centres

the drill, and the fibres are separated with

either angled chipping bevels or relief-ground

lips. An extra-deep and steep flute for chips

ensures efficient elimination of the chips.

Depending on the intended use, the drills are

made of tool steel (softwood) or heat-

resistant HSS steel (hardwood).

Forstner bits

Due to their short head with a small centring

brad point, the rotating cutting edge, and two

horizontal cutting lips, Forstner bits have a

function similar to routing. They allow clean

bores with an exact diameter. They are well

suited to countersinking, blind holes, cham-

fered bores at the edge of a workpiece,

re-boring existing bores, drilling end grain,

skewed-angle bores, and drilling out knots.

Multi-use twist drills

The multi-use twist drill made of HSS solves

a multitude of problems. Thanks to its high

heat resistance, it can be used on a wide

range of materials. It has an ultra-flat flute

profile which guarantees good cooling of the

cutting edges. Suitable for all materials that

produce medium and long shavings, such as

soft metals, stainless steels and wood.

DRILL CHUCK TYPES:

Three-jaw chucks

The most widely used chucks, predominantly

for cylindrical shafts.

Four-jaw chucks

Suited for square shaped shafts (good hold)

and cylindrical shafts, but not for hexagonal

shafts.

THE RIGHT BIT FOR THE RIGHT JOB

For the right bit, it`s not only necessary to

match the screw, but also to stand the stress.

The range of bits offered on the market,

which seems to be confusing for amateurs,

is due to the many improvements by screw

and bit manufacturers, who constantly

develop their products, and therefore offer

many different bit versions.

Slotted screw

The slotted screw was the first screw

on the market and is still used today.

The disadvantage of this head shape is that

the bit can easily slip through, which might

damage the screw. Also when the screw is

turned quickly, the bit may slip off. This

screw head shape is mainly used for manual

screwing.

Phillips screw (Phillips, PH)

To improve slotted screws, a second

slot was added to the screw head, and in

order to provide more contact surface the

centre was widened as well. This head shape

prevailed for a long time. The bit cannot

move outside, but if the contact pressure is not

strong enough, it might slip and oscillate,

which could also damage screw and bit.

Pozidriv screw (PZ)

The Pozidriv screw is an improvement

of the Phillips screw, as it provides not only a

cross-head but also additional notches.

The bit provides edges that grip into the

notches. This design protects the bit from

slipping through.

Torx screw

The advantage of Torx screws is the

extended grip surface for the bit.

Instead of two slots, as on a Phillips screw,

the Torx screw has three slots shaped like a

hexagon head. The rounded edges help

prevent material fatigue.

Allen screw

The Allen screw can also be conside-

red an improvement of the Phillips screw.

Like the Torx screw, the Allen screw also

provides an extended grip surface, and

it is very robust. However, this screw

is not suitable for fast-turning machines,

but is more widely used for manual screwing,

especially in the metalworking field.

Some manufacturers develop specific head-

shapes for their screws. Other developments

include Torx Plus screws, Tri-wing screws,

square-head screws and other newly develo-

ped shapes that are only used for specific

applications (for example in the field of auto-

motive, electrical, and safety engineering).

Bit sets (standard quality)

Basically, the bit material must satisfy two

requirements: it must be hard and tough.

However, because these are contrasting

properties, the choice of material is crucial.

For standard-quality bits, a tough steel is

used that doesn't break easily and still has

good hardening properties.

Bit set (torsion development)

The harder the bit, the longer its edge life,

but with the disadvantage that the bit be-

comes brittle and breaks easily. In the

development of these torsion bits, different

applications (wood/metal) were analysed and

the corresponding torsion forces determined.

Based on the findings, a steel was chosen

that is optimally tough for the given

application but still very hard.

THE DIFFERENCE IS IN THE DETAILS

Drills, pliers, screwdrivers || Drilling tools

141

Drill chucking tools

A BRACEIf there is no power supply or you have to bore extremely delicate holes, it isadvisable to use a brace. This Frenchmodel works extremely smoothly due tothe ball-bearing mounting of its head.The chuck has a right-left adjustableratchet, which enables drilling andscrewing even in confined spaces.Jaw opening 3.5-16 mmOverall length 360 mm1100 gChuck3-jaw No. 707182 50.34 € 59.90 € 4-jaw No. 707283 50.34 € 59.90 €

B PRECISION DRILL SET, 7-PIECE SETJapanese auger bits for drillingprecise, smooth and tear-freeholes in wood. Double bevelbits with pre-cutters and fine screw points. Hard-chrome-plated tool steel (rust-proof). Cylindrical drill bits Ø3/4/5/6/8mm, conical bit forplastic materials Ø 6mm, and conical bitfor making Ø 3mm pilot holes, all withhexagonal shafts. Set, hand brace and drill bits Ø 3-8 mm.Overall length 230mm 100 gNo. 717250 37.73 € 44.90 €

C HAND DRILLSmall hand drill with bevel gear drive,made in Germany. Hardwood handle,fast-action chuck (Ø max. 8mm).Overall length 295 mm570 gNo. 717249 26.47 € 31.50 €

F KANZAWA® ANGLE DRILL HEAD90°-head for drilling in corners and in conditionswhere space is limited (dis-tance to wall min. 20 mm).The handle can be attachedin 3 different positions. Aluminium housing, ball- bearing shafts, 3-jaw chuck1.5-10 mm, hexagonal driveshaft 8 mm. includes key.17 x 36 x 62 mm500 gNo. 717212 38.57 € 45.90 €

E DRILL STAND WITH CHUCKThanks to the integrated geared-rimchuck, this drill stand is ideal for usewith cordless screwdrivers. Precise guidefor 90° drillings, but you can also achieveother drilling angles by sliding the guiderods through the base. Manually adjust-able depth-stop rings, non-slip rubberbase, V-shaped support for round workpieces on the top of the base.Height 350 mmSupport table Ø 130 mmJaw opening 0-13 mmNo. 716149 96.55 € 114.90 €

A

D HAND DRILL WITH BREAST PLATEHand-driven drill. Two speeds by inter-changing the crank and side handle. Closed housing of diecast aluminium,hardwood handles, three-jaw chuck (diameter max. 10 mm). Made in Germany.Length 360 mm1325 gNo. 717251 65.55 € 78.00 €

B E

C

F

D

Drill chucking tools


142

Bit chucking heads and bits

A FLEXIBLE SHAFT

No. 717216 29.33 € 34.90 €

C CRAFTSMAN’S BIT SET, 31-PIECE

No. 707400 33.53 € 39.90 €

D MIDI-BOX CLASSIC, 21-PIECE BIT SET

No. 707401 16.72 € 19.90 €

Wood and metal drills

Do not use conventional twist drillswhen drilling wood, because they aredesigned for metal and have an un-suitable cutting-edge geometry whichleaves small grooves in the wood.

F AUGER BIT WITH SCREW TIPSCoiled wood drill bits for cutting cleanholes, with screw tips and spurs. For usein either a brace or speed-controlledpower drill.Overall length approx 235 mm

Diameter1 19 mm No. 717235 12.52 € 14.90 € 2 25 mm No. 706021 13.03 € 15.50 € 3 30 mm No. 706022 16.72 € 19.90 €

G AUGER BITS, 6-PIECE SET6-piece set, in wooden case. Ø 10/12/14/16/18/20 mmOverall length approx. 235 mmNo. 706023 29.33 € 34.90 €

Price advantageH WOOD TWIST DRILLS, HSS STEEL,8-PIECE SETTen times the service life:Made of heat-resistant,wear-resistant HSS steel.Ideal for heavy-duty drill-ing in hardwood. Theedges last 10 times aslong as carbon-steel bits. Taper-groundlips for perfectly clean boreholes. 8-pieceset, 3/4/5/6/7/8/9/10 mm. No. 706048 50.34 € 59.90 €

J WOOD TWIST DRILLS, 8-PIECE SETPrimarily for drilling softwood. With two pre-cutters, deep groove. 8-piece set, 3/4/5/6/7/8/9/10mm.Carbon-steel.No. 706049 6.64 € 7.90 €

I DRILL STOPS, 7-PIECE SETSlide-on rings with lockingscrews for wood and metaldrills. These serve as simple and effective depth stops when drilling.Ø 3.2/4.8/6.4/8/9.5/11.1 and12.7 mm, including Allen keyfor locking screws.No. 701879 5.46 € 6.50 €

E POWER DRILL BITSExtra-long Jennings auger bits withscrewtips and spurs, for carpentry,log building (for inserting long dowels),pre-drilling wooden mortises and making woodwind instruments.High quality, made in Japan.

The power drills have bit heads with cross-sockets for inserting a crank handle.Overall length 600 mmCutting length 500 mmHexagonal shaftDiameter15 mm No. 717260 21.76 € 25.90 € 20 mm No. 717261 30.17 € 35.90 € 25 mm No. 717262 37.73 € 44.90 € 30 mm No. 717263 43.61 € 51.90 €

A

H

J

E GF

I

C

D

B

1 2 3

Price advantage

For individual drills, visitwww.more-than-tools.de

Made in Japan by the market leader inautomotive tools, this flexible shaft canbe used with both normal cordless screw-drivers and cordless impact screwdrivers.At 330 mm long, the flexible bit holderis ideal for inaccessible spots, whether in the engine compartment or when ass-embling furniture or wooden structures.You simply bend the shaft into the opti-mum working position at the front handrest and hold it by this rest. Thanks to aquick-change fastener, the bit is lockedsecurely in place. Comes with two-sidedPH2 bit.Overall length 330 mm

Standard quality (58-60 HRC). With this tool set from the German market leader you can handle anystandard screw, whether Phillips head,flat head, Pozidriv, Torx or hexagon socket. Set with a magnet holder 6.35 mm (1/4") and 30 bits in solidmetal box.

Standard quality (58-60 HRC). Heavy-duty set from the German marketleader with 20 bits (Phillips head, Pozidriv, Torx or hexagon socket) and amagnetic holder.Comes in a handy plastic box.

B WIHA® 11-PIECE BIT SET HOTExtra-hard torsion bits (62 - 63 HRC).Especially suitable for turning screws inwood. When screws are turned into wood,the bit and screw head are under increas-ing torsional stress. This torsional stressis perfectly absorbed. The bits come in abox made of impact-resistant plastic,which may be opened one-handed. Slot-ted, Phillips and Pozidriv. Bits with bitholder.No. 717857 15.04 € 17.90 €


143

E LONG MULTIPURPOSE TWIST DRILLSThese HSS drills with an ultra-flat fluteprofile can be used for many materialssuch as iron and non-ferrous metals, butalso for wood and plastics. In particularthe drills are excellent for riveting knifehandles, which involves precise drillingthrough often all kinds of different materials.Overall length 100-139 mmCutting length 66-91 mmDiameter3.0 mm No. 717450 7.98 € 9.50 € 3.5 mm No. 717451 9.16 € 10.90 € 4.0 mm No. 717452 9.75 € 11.60 € 4.5 mm No. 717453 10.84 € 12.90 € 5.0 mm No. 717454 12.52 € 14.90 € 5.5 mm No. 717455 13.36 € 15.90 € 6.0 mm No. 717456 14.20 € 16.90 €

F HEX SHANK TWIST DRILL,5-PIECE SETEvery craftsman should possess such anassortment of metal drills featuring themost popular diameters. Due to the hexshank ideally suited for bit holders. Thehex shank also prevents slipping of thedrill in the chuck – an important feature.For superior cutting performance, thecross-shaped drills are precision-ground.Comes in plastic box. Diameters: 3/4/5/6/8 mmOverall length 60-70 mmNo. 707370 33.53 € 39.90 €

C ADJUSTABLE DRILL BITWood drill bit for brace, seamlessly adjustable from Ø 22 mm to Ø 76 mmvia two sliding cutters. Shaft suitable for three-jaw chuck.Overall length 160 mmNo. 707181 20.08 € 23.90 €

G AUGER GIMLETS, 7-PIECE SETAlso for children:These hand-drills are popular with every-one, not just the nostagically-inclined.They are light, the drill pulls itself into thewood due to the tapered screw tip and thedeep grove guarantees good chip removal.In addition, their slightly tapered shapeleads to greater tensile strength of screwjoints. 7 pieces in cardboard box.Diameter 2.0/2.5/3.0/3.5/4.0/4.5/5.0 mm. No. 701884 7.39 € 8.80 €

E

F

B

G

C

A

1

Forstner bitsFor drilling exact holes with smooth walls and flat bottoms. Suitable fordrilling countersink holes, blind holes,mortise joints and skewed-angle or diagonal holes.

A WAVE CUTTER® FORSTNER BITS

1 Single drillsØ Shaft Ø

15 mm 8 mm No. 707380 15.04 € 17.90 €20 mm No. 707381 16.72 € 19.90 €25 mm No. 707382 18.66 € 22.20 €30 mm No. 707383 20.92 € 24.90 €35 mm 10 mm No. 707384 24.54 € 29.20 €40 mm No. 707385 28.49 € 33.90 €45 mm No. 707386 34.37 € 40.90 €50 mm No. 707387 38.82 € 46.20 €60 mm No. 707388 62.94 € 74.90 €

See www.more-than-tools.de for Wave Cutter® Forstner bits

4 Extension for Wave-Cutter® Forstnerbit with cylinder shaftWith locking screws.Length 330 mmfor shaft Ø 8 mm No. 707390 21.76 € 25.90 € 10 mm No. 707391 21.76 € 25.90 €

B FORSTNER BITS, 10-PIECE SETForstner bits with conventional straightcutting edges, made of carbon steel. 10-piece set in wooden case, Ø 6/10/12/16/20/22/25/32/35/38 mmNo. 706035 25.13 € 29.90 €

D MILLING DRILL BIT

No. 717252 16.72 € 19.90 €

32

4

D

2 Wave-Cutter® 5-piece Forstner bit set(with cylinder shaft)5-piece set (Ø 15/20/25/30/35 mm) up to Ø 30 mm: shaft 8 x 30 mm, fromØ 35 mm: shaft 10 x 30 mm.In beechwood case.No. 707389 79.83 € 95.00 €

3 Wave-Cutter® 16-piece Forstner bitset (with cylinder shaft)16 pieces (Ø 12/15/16/18/20/22/24/25/26/28/30/35/38/40/45/50 mm), up to Ø 30 mm: shaft 8 x 30 mm, fromØ 35 mm: shaft 10 x 30 mm. In beechwood case.No. 707396 234.45 € 279.00 €

Twist drill with milling teeth in the middleof the tool. To create notches or widenexisting cut-outs, you drive the drill intothe workpiece and move it horizontally.The hexagonal shank prevents it fromslipping right through. For plywood up to10 mm thickness.Ø 6 mmOverall length 102 mmUseful length incl. tip 63 mm

This drill cuts particularly easily and produces exact, tear-free, blind holeswith smooth walls in softwood and hard-wood - even with edge boreholes and an-gled boreholes. Thanks to patentedwave-shaped cutting rims the friction is reduced, heat build-up avoided and a long service life achieved.

Forged head with wide chip channel for better chip ejection, brad-point tip.Overall length 90 mmWorking length 60 mm


144

Countersinks and countersink drills

A CONICAL, ADJUSTABLE COUNTER-SINK DRILL, 7-PIECE SETFor better-looking andstronger screw joints:The pre-drilling of woodscrews takes on a differentquality with this countersinkdrill. Greater tensile strengthis achieved with the tapereddesign than with cylinderdrills; at the same time therisk of screw breakage is reduced. The drilling depthis precisely adjustable tothe borehole depth by means of an adjusting ring. Thecountersunk head is alsoadjustable in depth, so thata dowel can be inserted ifrequired (for invisible screwjoins). A steep and deepgroove prevents pluggingand overheating of the drill. Manufactured inJapan from wear-resistantHSS steel.Overall length 80-100 mmNo. 71732767.14 € 79.90 €

B COUNTERSINK DRILL, 2-PIECEJapanese precision tools for countersink-ing and capping wood screws. Made ofheat-proof, wear-resistant HSS steel.Hexagonal shaftLength 20 mm

Diameter Ø 8 mmTapered pre-cutter Ø 3 mm, countersunkhead Ø 8mm, dowel cutter Ø 8 mmNo. 701871 26.64 € 31.70 €Diameter Ø 10 mmTapered pre-cutter Ø 3.5 mm, countersunkhead Ø 10 mm, dowel cutter Ø 10 mmNo. 701872 28.49 € 33.90 €Diameter Ø 12 mmTapered pre-cutter Ø 4 mm, countersunkhead Ø 12 mm, dowel cutter Ø 12 mmNo. 701969 33.36 € 39.70 €

See our webshop at www.more-than-tools.de for replacement drill bits.

When sharpening drill bits (or other tools with difficult geometry) it is a good idea to blacken the surfaces to be ground with a waterproof felt-tip pen.This allows you to see at a glance which surfaces have already been ground.

Auger bits made of carbon steel can be sharpened themselves with warding files(e.g. needle file No. 705041) or a suitable diamond file.Only sharpen the inside of the pre-cutters and the bevelled edge.

D 90° COUNTERSINK WITH BIT CASE,6-PIECE SETFor screwing countersunk head screws,for countersinking and deburring bore-holes in wood, non-ferrous metals, alloyed and unalloyed steels. Thesecountersinks with three blades groundinto the hardened steel are chatter-proofand feature low heat build-up, outstan-ding chip ejection and high-quality surface finish. 6 countersinks, 90°,creep-resistant HSS steel, with hexagonal shaft (Ø 6.3/8.3/10.4/12.4/ 16.5 and 20.5 mm) with bit case. In a robust metal case.No. 707392 83.19 € 99.00 €

C CROSSHOLE COUNTERSINK,4-PIECE SETThese 90° crosshole countersinks forwood are hardened to 62-64 HRC andare ideal for flawless countersinking. Thecrosshole provides excellent chip clea-rance and prevents jamming with theworkpiece. The special edge geometry ofthese outstanding countersinks allows forchatter-free and burr-free operations. Hex shank forms a reliable stop. For drillhole diameter 2-5/5-10/10-15/15-20 mm,in metal case.No. 707468 67.14 € 79.90 €

For individual sizes, visitwww.more-than-tools.de

B

A

F

E

D

Cylindrical and tapered cutters

F TAPERED PLUG CUTTERSFor cutting slightly conicalwooden dowels for closing drillholes, max. length 12 mm.Diameter6 mm No. 701860 4.96 € 5.90 € 8 mm No. 701861 5.46 € 6.50 € 10 mm No. 701862 5.80 € 6.90 € 12 mm No. 701863 6.39 € 7.60 € 16 mm No. 701864 6.97 € 8.30 €

E CYLINDRICAL AND TAPERED PLUGCUTTERS, 8-PIECE SETFor making wooden discs and plugs forsealing boreholes, restoring knots, etc.The tapered cutters facilitate a seamlesstight fit. Set includes four cylindrical andfour tapered drills of hardened tool steel(resharpenable) in a wooden case.Length 10-25 mmNominal Ø 8/10/12/16 mmNo. 701865 27.39 € 32.60 €

I JAPANESE KNOT REPAIR SETThis precision conicaldrill and dowel cutterset can be used to re-pair loose or unsightlyknots and other defectscleanly and efficiently.Conical dowels can be fitted more tightlythan cylindrical dowelsand do not diminish the strength of thepiece when glued inplace. We recommend using a Japanese flush-cut-ting Kugihiki saw (e.g.

No. 712321) forcutting off the tops ofthe dowels. Hole Ø 5 -25 mm, drill length80 mm, HSS drill bit,aluminium dowel cut-ter, resharpenable car-bon-steel cutter. Withwooden case and in-struction booklet.No. 717255 104.96 €124.90 €

No. 717256 25.13 € 29.90 €

G TAPERED SPOON BITFor making cylindrical holes conical and fordrilling skewed-angleconical holes for chairlegs, arm rests, etc.Overall length 175 mmTaper length 120 mmTaper 1/4.5Max. Ø 32 mmNo. 706999 46.13 € 54.90 €

Knot removing

Dowel cutting

Dowel inserting

Flush-cutting

H VERITAS® TAPERED DRILL BITWhen clamped in a brace with 4-jawchuck, this drill bit conically enlarges cylindrical holes. Your chair constructionis thus more stable and safe if legs orrungs are wedged from the rear and theresulting join is resilient to traction. Forboreholes with a diameter of 11-30 mm. Wedge angle 12.8°, to fit Veritas® cone cutter( No. 701880-82).Overall length 142 mmCone length 86 mmNo. 701867 28.49 € 33.90 €

No. 701868 5.80 € 6.90 €

G

I

H

C

Replacement blade Replacement blade


145

No. 701883 3.61 € 4.30 €

A VERITAS® CONE CUTTERFor cutting conical ends on cylindricalrods, e.g. Windsor chair legs, rungs, etc..Wedge angle 12.8°, adjustable bladewith straight cutting edge 63mm long,carbon steel (60 HRC), aluminium body. Suitable tapered drill bit No. 701867.Cone end Ø 15.9 mm (5/8")Max. rod Ø approx. 28 mm.No. 701882 20.08 € 23.90 €

B VERITAS® DOWEL AND ROD CUTTER

Ø mm Ø inch9.5 3/8 No. 706962 18.40 € 21.90 €

C ADAPTER FOR VERITAS®

DOWEL CUTTERSFits No. 706962.Ø 12.5 mm No. 706966 2.94 € 3.50 €

D DRIVE SHAFT FOR ADAPTERN0. 706968 1.60 € 1.90 €

E VERITAS® DOWEL ROD CUTTER

No. 703657 209.24 € 249.00 €Replacement blade (pre-cut) No. 703664 17.48 € 20.80 €Replacement blade (post-cut) No. 703665 19.24 € 22.90 €

F ADDITIONAL TOOLS FOR DOWEL ROD CUTTER (GUIDE BUSHINGS ANDSQUARE SOCKETS)Ø 6.3 mm (¼").No. 703658 37.65 € 44.80 €

Ø 7.9 + 9.5 mm (5/16" + 3/8").No. 703659 39.33 € 46.80 €

Ø 11.1 + 12.7 mm (7/16" + 1/2").No. 703660 39.33 € 46.80 €

Ø 14.3 + 15.9 mm (9/16" + 5/8").No. 703661 39.83 € 47.40 €

Ø 17.5 + 19.0 mm (11/16" + 3/4").No. 703662 40.25 € 47.90 €

Ø 20.6 + 22.2 mm (13/16" + 7/8").No. 703663 41.93 € 49.90 €

D

C

E

B

A

F

G I

K

G VERITAS® TENON CUTTERS,ROUNDED SHOULDERSThe mortise and tenon joint is a sturdywood joint ideal for making chair legs,rungs, frames and other structures. With rustic and green wood furniture theyallow elegant, glue-free construction ofhigh durability. Driven by an electric drillor brace (with brace adapter), these Veri-tas cutters produce smooth precision-cuttenons with rounded shoulders. Well-bal-anced, anodised aluminium body with a high-performance tool-steel cutter. A built-in spirit level facilitates in-linecutting.Max. tenon length approx. 68 mmHexagonal shaft 8 mmØ Tenon Ø inch16 mm 5/8 No. 706980 80.59 € 95.90 €19 mm 3/4 No. 706981 82.18 € 97.80 €25 mm 1 No. 706982 83.87 € 99.80 €32 mm 1¼ No. 706983 92.35 € 109.90 €38 mm 1½ No. 706984 95.71 € 113.90 €50 mm 2 No. 706989102.44 €121.90 €

Mortise joints on a green wood chairby T. Grögler.

Tip: Mortise joints tighten themselves if the timber moisture content of thetenon is lower than that of the counter-piece with the mortise hole when it isfitted (green wood carpentry).

H ADAPTER FOR VERITAS®

TENON CUTTERWith rectangular shaft for mounting in a brace. Fits No. 706980-82.No. 706992 7.06 € 8.40 €

L CYLINDRICAL TENON CUTTERS, 5-PIECE SETDouble function: Tenon and disc cutter!Powerful pilot-hole drill for cutting cylindricaltenons for mortisejointing as well asfor making wooden dowels up to 70 mmin length. 5 pieces in a wooden case,carbon steel.Tenons Ø 10/12/16/20/25 mmNo. 701870 46.13 € 54.90 €

I ROUNDING PLANE, 3-PIECE SETFor quick and easy cutting of short cylin-drical rods or tenonsfrom round or squarestock. Carbon steel cutter, resharpenable. 3 pieces, end diameter 12/18/25 mm.No. 707211 20.08 € 23.90 €

No. 707212 10.00 € 11.90 €

K POINTER PLANEFor sharpening theends of cylindrical rods.Max. rod Ø 25 mmNo. 707215 12.52 € 14.90 €

No. 707216 3.87 € 4.60 €

J DOMING PLANE, 3-PIECE SETFor rounding the headsof cylindrical rods. 3 pieces, Ø 12/18/25 mmNo. 707213 21.34 € 25.40 €

No. 707214 10.00 € 11.90 €

H

J

L

This practical tool isused to produceprecisely roundedrods and dowels fromsquare stock. Using ahand drill and adapter,the square-shapedwood is driventhrough the dowelcutter, which is att-ached to the work-bench. For short pieces and for cuttingtenons, the dowel cutter can also beturned by hand on a firmly clamped work-piece. The curved blade facilitates cleanand easy cutting, and by adjusting theblade the diameter can be fine-tuned.Length of cutters 60 mm Aluminium bodyLength of cutters 60 mm

Repl. blade No. 706965 4.37 € 5.20 €

No. 706990 16.72 € 19.90 €

Replacement blade

An ingenious tool which lets you makeperfectly sized dowel rods from squaretimber.

Simply make slightly oversized (+ 3mm)square blanks and use a power drill todrive them through the dowel maker. The tool has two blades (pre-cutters andpost-cutters), a micrometre adjustmentmechanism and square socket. Ideal formaking toys, models and furniture andfor restoration work. Anodised aluminiumbody with screw-on foot, 2 A2 high-per-formance steel cutters (pre-cutters andpost-cutters) and 2 guide bushings aswell as a square socket drive with powerdrill adapter. Basic set Ø 25 mm (1").

Replacement blade

3 replacement blades


Replacement blade

Drills, pliers, screwdrivers || Drilling tools, Screwdrivers

146

C HOLE CUTTER WITH KNOB HANDLE, SMALLFor veneers, guitar sound holes, leather,paper, cardboard, etc. Centering tip, incl.4 resharpenable blades in receptacle(knob handle), aluminium body with scale,knob handle with quick-adjustment mechanism. Diameter Ø 40-210 mm.No. 716163 15.63 € 18.60 €

E HOLE CUTTER WITH KNOB HANDLE,LARGEThis large hole cutter with a solid-steelguide is suitable for cutting holes with upto 660 mm diameter. A knob handle atthe centering tip which can be rotated inany direction allows convenient cutting,while the quick-adjustment mechanismand scale allow the cutter to be positio-ned easily. Includes 4 resharpenable blades in receptacle (knob handle).Diameter Ø 110-660 mmNo. 716148 36.89 € 43.90 €

B HOLE CUTTER WITH HANDLEThe long, chrome-plated handle with a textured shank is locked in place on thealuminium guide rod by turning the cen-tering tip. An extra-hard cutter (68-70HRC) can be adjusted by the lockingmechanism at the end of the guide rod.For use on leather, cardboard, gaskets, veneers etc. Diameter Ø 30-330 mmNo. 708345 30.17 € 35.90 €

D WOOD THREADING TOOLS, 2-PIECE SETSFor making practicalwooden threads with a virtually unlimited numberof applications for makingfurniture, racks, toys, nutcrackers, lamps etc.Two-piece set (thread boxand tap), for cutting inter-nal and external threads. Tap made ofhardened tool steel, hardwood thread boxwith a removable hardened steel cutter.The pitch of screw thread is given perinch. Suitable dowel rods ( No. 831001-05)

12.5 mm (½"), pitch 8.No. 707185 40.76 € 48.50 €

19 mm (¾"), pitch 6.No. 707186 41.60 € 49.50 €

25 mm (1"), pitch 6.No. 707187 43.70 € 52.00 €

32 mm (1¼"), pitch 6.No. 707188 49.58 € 59.00 €

38 mm (1½"), pitch 6.No. 707189 52.10 € 62.00 €

External screw threads are cut moreeasily and cleanly if the wooden rodsare first laid in linseed oil. Also makesure that hardwood blocks are welldried out and that your cutting edge is sharp.

Circle cutters and threading tools

A JAPANESE CIRCLE CUTTER

No. 716165 31.85 € 37.90 €2 replacement blades No. 716166 11.01 € 13.10 €Additional arm, up to 200 mmNo. 716167 6.22 € 7.40 €Additional arm, up to 300 mmNo. 716168 9.92 € 11.80 €

Screwdrivers

F JAPANESE ANEX HYPER®

SCREWDRIVERSDespite being one of the tools tool designers just love to toy with, screw-drivers are not immune from frustratingshortcomings such as broken blades anduncomfortable handles. For the Japanesemarket leader Anex, only uncompromisingfunctionality counts:

• The blades are hardened to 60 Rock-well along their entire length and haveabraded precision heads with the highestlevel of grip and wear-resistance.

• The anti-twist mechanism holding theblades in place will not loosen even afteryears of heavy-duty use.

• The delta-shaped wooden handles rest comfortably in the hand and lend the tools an aesthetically pleasing touch. The reinforced ferrules at the tops andbottoms of the handles can even bestruck with a hammer for heavy-duty applications.

• Chrome-plated blades and ferrules,magnetised tips.

1 Flat headWidth 5.5 mmThickness 0.7 mmBlade length 75 mmOverall length 180 mmNo. 717800 8.32 € 9.90 €

Width 6.0 mmThickness 0.8 mmBlade length 100 mmOverall length 220 mmNo. 717801 9.66 € 11.50 €

Width 8.0 mmThickness 1.0 mmBlade length 150 mmOverall length 285 mmNo. 717802 13.19 € 15.70 €

2 Phillips headNo. 1Blade length 75 mmOverall length 180 mmNo. 717803 8.32 € 9.90 €

No. 2Blade length 100 mmOverall length 220 mmNo. 717804 9.66 € 11.50 €

No. 3Blade length 150 mmOverall length 285 mmNo. 717805 13.19 € 15.70 €

G WOODEN SCREWDRIVERS, 5-PIECE SETWith a full-length blade made from achromium-molybdenum-vanadium alloy,these screwdrivers can resist even thestrongest forces. A forged-on hexagon allows you to use a spanner for effectiveforce transmission. The curved beechhandle provides a non-slip grip, has aroll-off guard where it meets the hoopand a leather splinter-protection cap atthe end of the handle.Overall length 80-150 mmFlat head 5.5 / 7.0 / 9.0 / PH1 / PH2No. 717814 21.76 € 25.90 €

H RATCHET SCREWDRIVERFor decades this tool has proven itself a classic, equally valued in boat con-struction and for assembly and restora-tion tasks. Screws can be inserted andremoved rapidly, even in tight spaces.The chuck can be switched to the left orright and locked. Hardened and smoothlyoperating rotating mechanism with a longservice life, beech handle. Comes with 3 bits corresponding to DIN 7432 (flat and Phillips head).Overall length480 mmNo. 707130 41.60 € 49.50 €

I BIT ADAPTER FOR RATCHETSCREWDRIVERSince the ratchet screwdriver only ac-commodates special bits (according toDIN 7432), this adapter is a recommen-ded accessory. It allows the use of com-monly available 6.35 mm standardhexagonal bits. Magnetic 72 x 6 mm.No. 707129 6.89 € 8.20 €

A

D

B

C

E

G

1 2

F

H

I

10 replacement bladesNo. 716169 4.12 € 4.90 €

10 replacement bladesNo. 716169 4.12 € 4.90 €

No. 707195 8.57 € 10.20 €

The inside and outside cutters ensureclean results even in thin or fibrous materi-als. Adjustable from Ø 30 mm to 120 mm,with an additional arm for holes up to Ø 300 mm. Resharpenable HSS blades,cutting depth of 28mm (56mm if cuttingfrom both sides). Driven by a controllable-speed drill. With instruction booklet.Please note: Additional arms are not included and must be ordered separately.

Replacement cutter

Drills, pliers, screwdrivers || Pliers

147

Pliers

A KEIBA® PLIERSThe better pliers:Axial and radial bronze bearings help give Keiba pliers an exceptionally smoothaction and make them practically non-wearing*. They are also bounce-free, for example whencutting hard wire.Forged from extra-hard Hitachi steel,working surfaceshardened to 60 HRC, handlescoated with nappedelastomer.

* In endurance tests, no measurable wear was determined, even after 100,000 opening and closing actions.

1 Combination pliersWith wire cutters.Overall length 175 mm236 gNo. 717815 27.90 € 33.20 €

2 Flat-round pliersExtra-slim, with wire cutters.Overall length 150 mm127 gNo. 717816 23.19 € 27.60 €

3 Wire cuttersSide cutting pliers with notch.Overall length 150 mm173 gNo. 717817 24.62 € 29.30 €

Bronze bearing

A MTC® JAPANESE PLIERSThese high-grade Japanese pliers have asensitive action but are also suitable forheavy-duty work. Made from the highest-quality Hitachi steels, well-proportioned,carefully hardened, individually inspected and adjusted.

1 Combination pliers

Length175 mm No. 717822 10.59 € 12.60 €200 mm No. 717823 11.26 € 13.40 €

2 Micro combination pliersFor precision work, with spring-loaded handle.Overall length 115 mm70 gNo. 717820 9.33 € 11.10 €

3 Needle pliersFor fine bending and gripping work,smooth jaws, spring-loaded handle.Overall length 125 mm64 gNo. 717825 9.16 € 10.90 €

4 Flat-round pliersExtra slim model. With wire cutters, ser-rated jaws, spring-loaded handle.Overall length 150 mm67 gNo. 717826 11.34 € 13.50 €

6 Wire cuttersExtra-hard (64 HRC), also suitable forpiano wire. Scissor-like cutting action forcleanly severing wires, nails, cables andropes up to approx. 6mm in diameter.Overall length 200 mm340 gNo. 717830 16.72 € 19.90 €

5 Precision pull pliersPrecision pliers for removing nails, pinsand staples. The rolling action of theextra-wide rounded head minimises pressure on the underlying surface, thus protecting the work piece.Overall length 150 mmJaw width 22 mm200 gNo. 717808 12.52 € 14.90 €

A

B

1 2 3

1 2 3 4

5

6

Tool handles without toxins – from DICK!

Alarming toxin levels in tool handles of cheap imports!News of toxic compounds in tool handles has surfaced again. Most of the tested products werecheap imports from China and Taiwan. Because of the regular enquiries we get from customers, wewant to tell you how we deal with thisvolatile topic. Our manufacturers are given clear instructions concern-ing the use of pollutant-free materials.At DICK, there are strict in-house inspections to ensure that the synthetic handles of the original DICKtools are free of harmful PAH.

Slim model. Grooved wire cutters with additional interior jaws.Weight 255 / 340 g

Drills, pliers, screwdrivers || Pliers

148

B SCREW-REMOVING PLIERSSpecially designedJapanese pliers forunscrewing tightscrews with a dam-aged head or slot. The sharp-toothedgrooves at the ends of the inner jawsallow you to grip andtwist round-head andcylinder-head screwsclose to the flange. Also useful forblocked and corroded steel screws orscrews with unusually shaped slots.

1 Screw-removing pliers, size 1Overall length 150 mm,max. head Ø approx.: front-end jaws 8 mm / side jaws 10 mm125 gNo. 717807 18.57 € 22.10 €

2 Screw-removing pliers, size 2The jaw opening can be conveniently adjusted with a sliding pivot.Overall length 175 mmmax. head Ø approx.: front-end jaws 10 mm / side jaws 14 mm190 gNo. 717847 20.08 € 23.90 €

A SOFT TOUCH - THE PLIERS WITH PROTECTIVE JAWSNo more dents on sensitive work pieces:With their replaceable plastic jaws,Japanese soft-touch pliers preservewood, precious metals, polished or varnished surfaces. The jaw opening can be adjusted to the workpiece with a sliding pivot. The soft handle coversensure that the pliers sit comfortably inthe hand. Powder-coated steel arms, adjustable movement.

1 Combination pliersWith wire cutters.Overall length 150 mm175 gNo. 717824 12.52 € 14.90 €

No. 800323 2.94 € 3.50 €

2 Water pipe pliersThe perfect pliers for gently gripping copper, plastic or stainless steel pipes.With replaceable plastic jaws.Overall length 250 mmØ 6-50 mmNo. 717836 22.86 € 27.20 €

No. 717837 2.94 € 3.50 €

3 Pipe pliersWith round and V-shaped jaws(Ø to approx. 70mm).Overall length 270 mm440 gNo. 717829 30.59 € 36.40 €Replacement jaws, roundNo. 800324 7.98 € 9.50 €Replacement jaws, V-shapedNo. 800325 7.98 € 9.50 €

D SHEET METAL SHEARSIdeal for precise sheet metal work:Japanese sheet metal shears for shortstraight and contour cuts with a wide radius to the left and right. The micro-toothing on the cutting edge preventsslipping, while the leverage saves effort.The multi-component handle made ofhigh-quality plastic provides a comforta-ble, non-slip grip. The cheeks made fromalloyed chromium molybdenum steelallow sheet steel of up to 1.2 mm andstainless steel panels of up to 0.7 mm tobe cut easily.Overall length 255 mmBlade length 45 mmNo. 708174 16.72 € 19.90 €

F MINI ADJUSTABLE WRENCHSmall adjustable wrench of chrome vanadium steel, hardened jaws, rubber-coated handle.Opening 17 mmLength 110 mm65 gNo. 717838 14.20 € 16.90 €

C PIANO WIRE CUTTERCuts cleanly and easily through steelwire, nails and bolts up to 3.2 mm diameter. Light construction, leverage adjustment, precisely guided, extra-hardcutting jaws. Safety locking in lockedstate. Self-opening handles of powder-coated sheet steel, adjustable stop screw, carrying strap.Overall length 200 mm270 gNo. 717831 18.74 € 22.30 €

E ADJUSTABLE WRENCHExtra-light:Light and durable adjustable wrench withperforated handle. The jaws are harden-ed, the surface chrome-plated andground at the edges. High-strength, for-ged alloy steel.Overall length 250 mmOpening max. 32 mm310 gNo. 717809 33.53 € 39.90 €

A

1 2 3

1

B

2

C D

E

F

Replacement jaws

Replacement jaws

Workbenches | 150

Accessories and clamping devices | 152

Tool sets | 154

Useful aids | 156

Workwear | 156

149

Working with method!

Benefits at a glance:- Robust design, high-quality

workmanship- Tool well, bench support, drawer- Numerous clamping options

Clamping possibilities

saving and functional workbench, e.g.goldsmiths, silversmiths, chair-makers, knifemakers... .

For this purpose it may be equipped withour excellent, professional bench dogs

No. 705924 and 705925. Left-handed version available (special order through customer service) at a 20% higher price.

Benefits at a glance:- Compact size- Different working heights- Same construction as professional

workbenches


Worktop thickness 90 / 45 mmOiled worktopIncl. 4 aluminium bench dogs (19 mm)Worktop dimensions 1170 x 560 mmOverall dimensions 1250 x 640 mmWeight approx. 50 kg

Workshop accessories and toolkits || Workbenches

150

Workbenches

-Workbenches

REPLACEMENT LEGS FOR-JUNIOR WORKBENCH

Height580 mm No. 706301 92.44 € 110.00 € 660 mm No. 706078 96.64 € 115.00 € 770 mm No. 706303 100.84 € 120.00 €

B -ALLROUND WORKBENCHThis workbench made from air-dried,steamed beech is impressive in its sturdi-ness and efficient construction. The mas-sive front vice with a maximum clampingwidth of 265 mm securely holds even large beams. To also span irregular work-pieces, the front vice is equipped withround bench dogs made from bronze.The rear vice, on the other hand, is fittedwith square steel bench dogs in traditio-nal shape to provide maximum clampingstrength. The integrated tool well not only has the advantage of storing toolsbut also reduces the solid part of the table top. Through this design detail,shrinkage is reduced to a minimum whileno benchtop space is lost. To keep theworkbench from warping it is securedwith a breadboard end. The drawer underthe table top is constructed with half-blind dovetails to make it aestheticallypleasing and to offer maximum stabilitycompared to doweled drawers. A warp-resistant frame ensures stability and,with its fixed board jack, offers moreclamping possibilities.

Model Allround 1600Worktop dimensions 1600 x 650 mmOverall dimensions 1840 x 830 mmWeight approx. 90 kgNo. 706305 999.16 € 1189.00 €

Model Allround 2000Worktop dimensions 2000 x 650 mmOverall dimensions 2240 x 830 mmWeight approx. 100 kgNo. 706306 1083.19 € 1289.00 €

A -JUNIOR WORKBENCHThe workbench which grows with your kids.First of all, a children's workbenchshould be adjustable and robust. Just likethis workbench, which is as rugged as areal workbench. The worktop is made ofoiled and damped beech (less likely to wrap) and secured through bread-board-ends. The feet are exchangeablefor longer feet which makes this work-bench a reliable longtime companion foryour children. Two vices offer variousclamping possibilities. Up to two childrenmay work at the same time. Four benchdogs made of aluminum casting allow forsecure hold in every position. Of coursethis workbench is not only suited for chil-dren but for everyone who needs a space-

Height670 mm No. 706300 365.55 € 435.00 €750 mm No. 706077 373.95 € 445.00 €860 mm No. 706302 382.35 € 455.00 €

A

B

Worktop securedthrough bread-board end

Below shot of front vice

Worktopsecured throughbread-board end


Tool well Drawer guide

Worktop thickness 100 / 50 mmHeight 870 mmOiled surfaceIncluding 2 square steel bench dogs4 long and 1 short round bench dogs(brass Ø 19 mm)

The workbench – one of the most impor-tant tools for many handicraft projects –will only become your life-long compan-ion if it is of extremely solid construction,high-quality workmanship and offers awide range of functions. Working closelywith renowned German workbench manu-facturers and based on our many years ofexperience in the trade, we have incorpo-rated all these needs in our workbenches.Workbenches are delivered unassembled(detailed assembly instructions included)Free shipping within Germany. For shipping outside Germany, pleasecontact our customer service.

No. 703653 8.32 € 9.90 €

No. 706080 251.26 € 299.00 €

The traditional shaving horse is an in-dispensable tool when working with draw-knives. Rods, rungs, table legs and otherlong, round or board-shaped parts can begripped with the foot-activated mechanismand then freely shaped with the use ofboth hands. Shaving horses allow you towork in a position which is ergonomic, reduces stress on the back and most importantly, is absolutely safe. Based ona Swedish model, the workbench presentedhere is light, sturdy and very versatiledue to the adjustable yoke and footrest.Pinewood bench, frame and legs. Supplied unassembled, with instructions.Length 125 cmBench height 54 cmMax. jaw opening 15 cm

No. 705627 174.71 € 207.90 € No. 705622 99.08 € 117.90 €

No. 705623 116.72 € 138.90 €

Workshop accessories and toolkits || Workbenches

151

Heavy, solid workbench of steamed redbeech, which will impress you not onlywith its outstanding quality but also withits functional design and well-thought-out accessories. The robust front vice,which also supports the workpiece andcan be locked in place, runs on a Ø 28mm double spindle for maximum forcetransmission. The tail vice with heavyGerman guide is torsion-resistant due to multiple glueing.Novel round bench dogs with steel boltsand replaceable aluminium caps allowpull and pressure clamping and securelyhold workpieces with both straight andround edges. Plastic pressure elementsintegrated in the shaft hold the roundbench dogs at any height, but also allowthem to be fully inserted in the worktop.Holes for round bench dogs in the frontand tail vice allow you to clamp workpie-ces in front of the workbench. In combi-nation with additional clamping holes inthe worktop and on the sides, and usingthe quick lever clamp, you can clamp al-most anything as required. Two thick breadboard ends protect the worktop optimally from warpage, while the extremely torsion-resistant underframewith 75 x 75 mm legs and stretcher rails(130 x 45) ensure stability. The 2000 model also features a tool wellfor storing tools. With the optionally avail-able accessories, you can upgrade yourworkbench to fit your individual needsand make it perfect for any use.

Benefits at a glance:- Ultra-solid construction- Unlimited clamping options- Front vice with double spindle

and workpiece support- Extra accessories for many

and varied uses


Model Deluxe 1600Worktop dimensions 1600 x 600 mmOverall dimensions 1780 x 820 mmWeight approx. 95 kgNo. 706089 1200.84 € 1429.00 €

Model Deluxe 2000Worktop dimensions 2000 x 640 mmOverall dimensions 2180 x 860 mmWeight approx. 125 kgNo. 706099 1536.97 € 1829.00 €

A -DELUXE WORKBENCH

B LEVER CLAMP

No. 705794 88.15 € 104.90 €

DrawerAn optional finger-jointed drawer on hanging guides under the worktop servesfor storing accessories (additional benchdogs and clamping devices) and tools.Outer dimensions 550 x 430 x 130 mm

Levelling supports in underframeFor easy and precise levelling of theworkbench, we also offer the Deluxeworkbenches with levellingsupports. By turning a car-riage bolt, you can adjusteach leg individually with-out inconvenient under-laying. This counteractsworktop warpage when theworkbench is set up on an uneven floor.

C BENCH SUPPORT

No. 705621 119.24 € 141.90 €

Wider worktopFor an even larger work area, Deluxeworkbenches are also available with a wider worktop. The solid worktop is 700 mm wide and has no tool well.

D SHAVING HORSE

VERITAS® SHAVING HORSE PLANBuilding plan of a traditional shaving horse with differentworking positions.13-page exact des-cription and detailedillustration on 12pages. In English,with inch measurements.

For Ulmia workbenches seewww.more-than-tools.de

A

D

Bench worktop secured throughbread-board end

Round bench dogholes on sides

Slightly angledfront vice for max.clamping pressure

Worktop thickness 100 / 54 mmHeight 930 mmOiled surfaceIncludes 4 short and 2 long round benchdogs (steel shaft Ø 20 mm)

B C


Novel clamp, created together with a re-nowned clamp manufacturer, for clampingworkpieces in the middle of the worktopor on the side of the workbench. Usingthis accessory on the Deluxe workbenchquickly solves any clamping problem, no matter how complex it may appear.

Due to the precisely defined hole diame-ter and the perpendicular position of theholes, the clamp can only be used withthe Deluxe workbench.Jaw opening 200 mmJaw depth 140 mm

The solid, height-adjustable bench sup-port allows you to support long boardsthat are clamped in the front or tail vice.Because it is the exact height of thebench (930 mm), workpieces lying onthe worktop thus also have a second leg. 930 x 360 x 360 mm

No. 705755 108.40 € 129.00 €

1 Jaw depth 100 mmJaw height 100 mmRod Ø 17 mmNo. 705756 7.06 € 8.40 €

2 Jaw depth 200 mmJaw height 220 mmRod Ø 22 mmNo. 705757 15.71 € 18.70 €

No. 705626 5.55 € 6.60 €

Workshop accessories and toolkits || Accessories and clamping devices

152

Accessories and clamping devices

A DELUXE BENCH DOGS, 1 PAIRRound bench dogs with steel bolts andreplaceable aluminium cap. Plastic pressure elements in the shaft hold thebench dogs at the required height.Shaft-Ø 20 mmHead-Ø 30 mmLength195 mm No. 705624 50.34 € 59.90 € 105 mm No. 705625 44.45 € 52.90 €

B CLAMPING SLEEVE FOR DELUXE BENCH DOGSTo provide the bench dogs with additionalsupport in the case of higher clampingforces, you can insert additional clampingsleeves into the recessed holes for theround bench dogs.

C VERITAS® BRASS BENCH DOGSCylindrical brass posts (Ø 18.8 mm) withside springs. The textured jaws have aninward cant (2°) to prevent the workpiecefrom slipping upwards. 2 pieces each.Fits No. 706300 / 077 / 302 / 305 / 306.Suitable auger:

No. 717235Length

1 60 mm No. 705924 16.72 € 19.90 € 2 110 mm No. 705925 20.50 € 24.40 €

D VERITAS® HOLD DOWN CLAMPA third arm at the workbench!Workpieces in all forms and shapes,which are hard to clamp down, can nowbe held in place easily and securely. Thetoothed rod is inserted into a horizontalor vertical 19 mm hole (drilled with auger No. 717235) on the workbenchplate. Tightening the nut activates theself-locking mechanism. Supplied withassembly instructions. Arm and body made of aluminium, steel rod. Fits No. 706300 / 077 / 302 / 305 / 306.Jaw depth 200 mmJaw height 200 mmNo. 705760 67.14 € 79.90 €

E ANANT® HOLD DOWN CLAMPHold down clamp based on a classicEnglish model with moveable pressureplate on the arm. The toothed rod runsthrough a flange, which can be mountedto the plate or to bench frame. Drop-forged arm and body.Jaw depth 200 mmJaw height 220 mmRod Ø 23 mmNo. 705937 33.53 € 39.90 €

F HOLD DOWN CLAMPSQuickly fastens all types of workpieces tothe joiner’s bench plate. The rod of theforged hold down clamp is slipped into adrill hole, self-locking mechanisms.

Length65 mm No. 705926 24.29 € 28.90 € 160 mm No. 705927 26.81 € 31.90 €

I PRECISION BENCH VICESSolid metal vice enables exact and quickclamping on the joiner’s bench. The greycast iron jaws run on two 22 mm strongsteel guide rods virtually free of play.Spindles have asymmetrically-shapedthreads to withstand extreme loads.Quick adjustment with the lever lockingmechanism prevents time-consumingwinding. The extendable dog enablesclamping of longer objects. Easy installa-tion by screwing the vice to the bottomof the bench plate (installation height60 mm), jaw drill holes for fasteningwooden blocks.

Jaw opening 190 mmJaw width 175Jaw height 75 mm9.2 kgNo. 705765 100.76 € 119.90 €

Jaw opening 300 mmJaw width 225 mmJaw height 75 mm14.5 kgNo. 705766 133.61 € 159.00 €

H STANDARD BENCH VICEMetal vice with double guide rods, trapezoidal thread, extendable benchdog. Screwed to the bottom of the benchplate (installation height 60 mm), jawdrill holes for fastening wooden blocks.Jaw opening 300 mmJaw width 180 mmJaw height 75 mm5.7 kgNo. 705768 35.21 € 41.90 €

J PATTERNMAKER´S VISEThis vice is one of the most versatiletools for the workbench top. The excep-tionally solid, grey cast iron heads can betightened parallel to one another or indi-vidually swiveled to accept oddly shapedpieces. The vice mounts through any holein the bench top (a dog hole will do).Once mounted, it canbe easily swiveled afull 360° and lockedin place via a wingednut. The swivel base can be either moun-ted above the bench top (working height

BA C

1 2

D

E

2

G

I

H

F

1

250 mm) or below (working height 215mm). Cast iron body, steel guide rails,trapezoidal threads on the spindle withhand crank, softwood jaws with soft polyurethane linings.Jaw opening 150 mmJaw width 125 mmBench top thickness max. 130 mm14 kg

J

G BENCH CLAMPS VERITAS®

These clamping tools will make yourworkbench even more versatile. The rodscan be inserted into a 19 mm drill holeanywhere on the bench’s top, front orframe. (Suitable auger No. 717235).Irregularly shaped workpieces are nomatch for this clamping system with itspull-out and rotational action. Rod andclamping spindle made of steel with gun-metal finish, brass knob handle and jaws.Fits No. 706300, -077, -302, -305, -306.Jaw size 50 x 15 mmSpindle length 100 mmBolt Ø 18.8 mm

No. 705932 10.00 € 11.90 €

No. 705929 92.35 € 109.90 €

For precise trimming and clean mitrecuts. Simply cut stock slightly oversizeand then make the final cut using themitre trimmer. Ideal for cutting frames,baseboards and also for precision 90°-cutting of scantling, poles etc. The sharp,skewed blades allow high-precision shearing cuts. The gear driven lever allows effortless use.

Heavy-duty, grey iron casting with pre-cisely machined working surfaces, double-sided guides and two finely adjustable,90° and 45° fences. Comes with two hardened tool steel cutting inserts, 6 mmstrong, which are detachable for easysharpening.Length 580 mmMax. stock size approx. 85 x 70 mmApprox. 12 kg

Workshop accessories and toolkits || Accessories and clamping devices

153

A MULTIPURPOSE BENCH VICEMultifunctional:The most diverse clamping tool for thedemanding woodworker: the main jawscan be adjusted conically up to 5° whilean additional jaw can be swivelled up to30° on a second axis. Without looseningthe clamp, the entire piece can be swungupwards and locked into any position upto 90° and rotated 360°. Four adjustablebench dogs accommodate pieces of var-ious shapes. The heavy grey cast ironconstruction holds work pieces securelyand reduces vibration, even under greatloads. This vice is easily attached to theworkbench by aligning the mounting plate flush with the bench top andtightening the support from below. In-structions included.Jaw opening 350 mmJaw width 345Jaw height 125 mmWeight 25 kgNo. 705767 251.26 € 299.00 €

B MITRE TRIMMER

No. 705798 158.82 € 189.00 €

C VERITAS® CARVER’S VICERobust sculptor’s vice with a fully rota-ting, height-adjustable plate. The sturdyarched aluminium body and secure clam-ping mechanism make this vice suitablefor heavy-duty work. The vice can be bol-ted to the bench or mounted in a dog ho-le (e.g. with auger no. 717235).Base 115 x 90 mmMax. height 240 mmPlate Ø 87 mm2.3 kg

D DOG HOLE MOUNTFor fastening a (rotating) vice to a plate drillhole, Ø 19 mm (e.g. drilled with auger

No. 717235).Length 125 mm1/2" screw thread

Clamping with benchdogs

360° rotation action

Additional jaw with swivel action

Angling the jaw with a cam lever

Tilting from a horizontalto a vertical position

B

A

C

D

E PARALLEL VICE HEUER®

The original from Germany:At its Plettenberg plant, the Germancompany Brockhaus started manufac-turing drop-forged vices with dual-prism,inside guide tracks in 1927, setting aworld-wide standard. The guide tracksprevent contamination and damages whilethe machined track surfaces guaranteeprecision and long service life. The centrally located and well-protectedspindle with double-action trapezoidthread gives the vice its high and optimallydistributed clamping force. Drop-forged,surface-hardened clamping jaws, pipe-gripping jaws and a rear jaw with smallanvil, giving this vice the ability to with-stand high loads, make this vice a versatileaid in the workshop.Jaw opening 150 mmJaw depth 65 mmJaw width 120 mmPipe-gripping jaws 16-55 mmApprox. 9 kgNo. 706100 154.54 € 183.90 €

E

No. 705830 46.13 € 54.90 €

H MULTI-ANGLE VISEThe ball-jointed foot can be adjusted toany angle, making the vice extremely ver-satile. The workpiece is screwed onto theplate from the bottom. The grub screwmakes the plate easilydetachable from the cen-tral mount.Base 140 x 125 mmHeight 125 mmPlate Ø 90 mm3.3 kg

H

G ROTATING PLATEThis makes your Heuervice (No. 706100) evenmore manoeuvrable.Completely steel-forgedrotating plate which canbe set to any angle quickly and securelyusing the spindle key. The closed con-struction protects the vice from shavingsand dirt. Extremely precise guide tracksthrough the accurately milled rotating as-sembly and support plate.Approx. 2.5 kgNo. 706101 50.34 € 59.90 €

F MAGNEFIX PROTECTIVE JAWSProtects your workpiecefrom dents. Aluminiumbody, easy and secure application using integra-ted special magnets. Despite the high amountof magnetic force, it doesnot penetrate to the clamping surfaces so thatthe workpiece is not mag-netised nor is swarf attracted.

1 Aluminium with groovesFor rough to medium fine workpieces.No. 706102 22.02 € 26.20 €

2 Aluminium with felt padFor highly sensitive workpieces.No. 706103 28.49 € 33.90 €

F

1 2

G

Mitre Chamfer

Butt joint Chamfered edges

No. 705826 62.94 € 74.90 €

Workshop accessories and toolkits || Accessories and clamping devices, Tool sets

154

Tool sets

D FOUR FILMS ABOUT DIFFERENTHANDCRAFT TECHNIQUES ON ONE DVDSchärfen mit Wassersteinen, Japanische Holzverbindungen, Shoji, Japanische Holzbearbeitungswerkzeuge.DVD, 135 minutes, in German.No. 713709 10.84 € 12.90 €

C TOOL SET »JUNIOR«A compact set of high-quality Japaneseand Swedish tools designed for youngwoodworkers and professionals workingin the field.Dozuki Universal Compact precision sawNo. 712848Ryoba Compact double-edged sawNo. 712849Tataki Nomi chisels: 9/12/18/24 mmNo. 710782, 710783, 710785, 710786Genno hammer, 375 g No. 714010Combination sharpening stone No. 711007Talmeter measuring tape, 2 m No. 708020Folding square, 300x175 mm No. 707298Cotton tool bag, 9 pockets No. 707511DICK cap No. 707550No. 718894 178.99 € 213.00 €

Tool carriersSystematic tool storage:For your tools ready at hand and a clear work-space: DICK tool carriers make sureyour workshop is tidy and with their mixof design and functionality, they are aperfect example of the DICK company philosophy. Each tool has its own placewhere it is safe and will not be damaged.When away on an installation job, youwill profit from having a light-weight selection of tools at hand to carry out virtually any type of job. The stable toolcarriers made of glue-laminated beechplywood are exclusively manufactured in Germany according to our company guidelines and quality standards. Thispractical tool carrier will simplify installa-tion jobs and be of great advantage to you in the workshop. The suitable plastic

»Japan« series

E SYSTAINER® WITHTOOL CARRIER »JAPAN« EQUIPPED,

19 ITEMSA practical selection of high quality Japa-nese tools from the DICK range, for allwoodworking tasks.The tool carrier isequipped with: Chisels No. 710781, -782, -783, -785,-786, -787; Saws No. 712809, -806, -602; Planes No. 717006, -041; No. 718804 483.11 € 574.90 €

Price advantage

A SWIVEL VICEA ball-jointed foot lets you rotate this solidvice about all three axes. The positioncan be set to meet the specific demandsof the workpiece, the two knob handlescrews allow for quick and secure faste-ning. Small anvil on the back. The baseplate can be fastened to the work platewith four screws. Replaceable jaws.Jaw opening 70 mmJaw width 80 mmOverall height 255 mm8.6 kg

B MULTI-ANGLE VICELight aluminium vice, rotatable in all directions, for light assembly or othertasks. Ball-joint with quick locking mechanism.Jaw opening 100 mmJaw width 75 mmTable clamps max. 53 mm1.2 kgNo. 705796 19.08 € 22.70 €

A B

Price advantage C

ESystainers® are standardised, durable andstackable. (The tool carriers are compatiblewith the commercially available plasticSystainers no. IV and V.). The tool sets»Japan« and »Cabinet-making and interiorwork«, compiled by specialists, will equipyour workshop with a whole range of pre-mium hand tools, perfectly stowed in theDICK tool carrier and an optional Systainer.

Your benefits:• Price advantage compared to the price

of the individual pieces!• All the individual tools are available

for purchase at all times.

Hammer No. 714103; Sharpening stone No. 711005; Set squares No. 717131, -132; Compass No. 707150; Marking gauge No. 717103.Length 360 mmWidth 270 mmHeight 280 mm7.7 kg

E

D

No. 718816 273.03 € 324.90 €

No. 718813 629.33 € 748.90 €

Workshop accessories and toolkits || Tool sets

155

»Cabinet-making and interior work« series

A SYSTAINER® WITH TOOL CARRIER»CABINET-MAKING AND INTERIOR WORK«EQUIPPED, 44 ITEMSAn assortment of basic hand tools for cabinet-making and interior work. This carrier also provides two additional compartments for small items. The tool carrier contains: Chisels No. 710781, -782, -83, -785, -786, -787; Saws No. 712848, -104; Planes No. 703108, -101; Pliers No. 717822, -808; Screwdrivers No. 717800, -801, -803, -804; Voltage tester No. 800330; Auger bits No. 706040, -041, -042, -043, -044, -045, -046, -047; Folding rule No. 708024; Parallel marker No. 716152; Marking gauge No. 707178; Folding square No. 707298; Spirit level No. 717156; Bit screwdriver sets No. 717851; -852; Hammer No. 714103; Titebond® No. 450360; 2 x clamps No. 705781; File No. 705023; File handle No. 704955 (not mounted); Cutter Bessey® No. 710540; Sharpening stone No. 711007; Sanding block No. 705120; Punch awl No. 717206; 2 DICK-pencils.Length 370 mmWidth 263 mmHeight 293 mm13.1 kg

B TOOL CARRIER »CABINET-MAKING AND INTERIOR WORK«EQUIPPED, 43 ITEMSFor contents of tool carrier see No.718813. Extendable up to 62 items see No. 718816. 11 kgNo. 718812 583.95 € 694.90 €

C SUPPLEMENTARY TOOL SET »SPECIAL«, 19 ITEMSFor DICK tool carrier »Cabinet-makingand interior work«, holds 43 items (No. 718812).The pack contains:Saws No. 712845, -602; Talmeter® marking measure No. 708021; Bevel No. 707311; Adjustable wrench No. 717809; Pliers No. 717836, -826, -807; Drills No. 707389; Rasp No. 704732; Rasp handle No. 704955; Punch awl No. 717205; Punch set No. 710797.

D SYSTAINER® WITH TOOL CARRIER»CABINET-MAKING AND INTERIOR WORK«WITHOUT CONTENTS, HOLDS 62 ITEMSFor 62 items plus compartments forsmall items. 4.7 kgNo. 718811 150.00 € 178.50 €

E TOOL CARRIER »CABINET-MAKING AND INTERIOR WORK« WITH-OUT CONTENTS, HOLDS 62 ITEMS2.6 kgNo. 718810 83.19 € 99.00 €

Price advantage

Price advantage

Price advantage

A

B

A / B

D E

C

No. 707667 8.07 € 9.60 €

No. 717513 8.32 € 9.90 €

No. 707550 4.96 € 5.90 €

No. 707220 4.96 € 5.90 €

Never cut your handsagain when workingwith sharp tools, sheetmetal or glass. Madeof extremely durableDyneema® yarn*, theselightweight gloves arehighly resistant to cutscaused by various types of tools. That makes them equally practical forworking with wood, using sharp chisels,saws, or carving gouges, glass, gardening,forestry, and as a locksmith. The glovesare also practical in vocational centres,for freehand sculpting and in craft edu-cation. Very thin and flexible, the backsof these gloves are made of breathablefabric and the interiors are coated withnon-slip rubber. The backs, interiors andcuffs are all protected. (Protection not for machine work andchainsaws). Protective category 3544 according to DIN EN 388.S = 6, M = 7, L = 8, XL = 9, XXL = 10.*Dyneema® is a high-tech fabric with atensile strength that is approximately 15 times stronger than steel. It is usedfor bullet-proof vests among other things.

No. 707615 5.55 € 6.60 €

No. 707668 12.52 € 14.90 €No. 707500 80.59 € 95.90 €No. 820205 14.20 € 16.90 €

Workshop accessories and toolkits || Useful aids, Workwear

156

Useful aids

A TOOLFIXExtra strength (can hold up to ca. 2.5 kg)magnetic tool bar. For easy access toyour tools. Black plastic body, mountsusing screws.349 x 34 x 23 mmNo. 707210 21.76 € 25.90 €

B DOUBLE-SIDED MAGNETIC TOOL BARMaximum strength (up to 10 kg) tool bar.Can be mounted using screws or via itsown magnetic power (on ferromagneticwall surfaces) Chrome-plated metal rails,2 mounting brackets.Cross-section 600 x 25 x 20 mmNo. 707222 18.40 € 21.90 €

C MAPLE TOOL BARMagnetic tool bar for hand tools and kitchen knives. Maple body with 2 permanent magnetic rails.Cross-section 460 x 47 x 22 mmNo. 707224 10.00 € 11.90 €

D TOOLHOLDER

Two frequently asked questions regarding magnetic tool bars:

Does magnetisation negatively affectthe sharpness of cutting tools? No, magnetising steel does not changeits crystalline structure. It can, however,complicate re-sharpening because themagnetised metal particles (swarf) tendto stick to the cutting edge.

Are all steels ferromagnetic? No, pure austenitic stainless steels(including many VA steels) are notmagnetic. However, these steels oftenhave ferritic elements, meaning thatthe majority of the steels used tomake stainless steel knives do stick to magnetic tool holders.

These ball transfer units allow you extendmachine tables and move heavy work-pieces wherever you need them. Thesteel balls, 25 mmdiameter, are fitted ina zinc-plated bearing,which can be fastenedeasily with two screws.6-piece set.

Workwear

F JAPANESE WORKING CLOTHESIts high-quality cotton cloth makes ithighly durable and responsive to humidity.Suitable for craftsmen, artists, painters,sculptors alike as well as for meditatingor simply wearing around the house.Strong cotton cloth, soft and pleasant tothe touch. Jacket comes with open, me-dium-length Kimono style sleeves, one side pocket and overlapping lapels to tie.Loose-fit trousers with cuffs and threepockets. Indigo.SizeM No. 707620 83.95 € 99.90 € L No. 707621 83.95 € 99.90 € XL No. 707622 83.95 € 99.90 € XXL No. 707623 83.95 € 99.90 €

K JAPANESE KNEE SOCKS, TWO PAIRS

L JAPANESE SOCKS (GUNSOKU), ONE PAIRFor Jika-Tabi. Elastic cotton fabric, rein-forced heel and toes, one size, beige/grey.

J 5-TOE SOCKS, FOUR PAIRSSeamless knitted socks with separate toes, in keeping with Japanese tradition.They allow better airing, and so help pre-vent sweating and athlete's foot. Blendedfabric of 85% cotton and 15% nylon.One size, black.

I JAPANESE SHOES (JIKA-TABI)WITH AIR SYSTEMJika-Tabi - Japanese worker's shoes - turnthe feet into fully functional clamping,climbing and gripping tools - for holdingworkpieces, artistic balancing on roofstructures or climbing. An integrated aircushion makes them gentle on the jointsand extremely comfortable to wear. Theseparate big toe provides full mobility,while the soft natural-rubber sole givesyou excellent balance and an almost barefoot feeling. The shoes are made ofhard-wearing double-layer cotton withreinforced toe, heel and sides and areclosed at the back with hooks. Colour:black.To determine your size, measure the fulllength of your foot and add 0.7-1 cm.E.g. foot length = 25.5 cm, Tabi size26.5 cmSize240 No. 707670 33.53 € 39.90 € 245 No. 707671 33.53 € 39.90 € 250 No. 707672 33.53 € 39.90 € 255 No. 707673 33.53 € 39.90 € 260 No. 707674 33.53 € 39.90 € 265 No. 707675 33.53 € 39.90 € 270 No. 707676 33.53 € 39.90 € 280 No. 707677 33.53 € 39.90 € 290 No. 707678 36.05 € 42.90 € 300 No. 707679 36.05 € 42.90 €

G COTTON APRONThe hefty cotton fabric is seamed on allsides, and impregnated to repel waterand dirt. The large, sealable front pocketis perfect for tools and materials whilethe small pouch serves to keep your glasses.Size60 x 82 cm No. 707505 29.33 € 34.90 € 90 x 87 cm No. 707506 33.53 € 39.90 €

H FRENCH LEATHER APRONThis heavy-duty leather apron providesreliable protection against dirt, dust,wood chips and shavings. Made from asingle piece of 2 mm thick leather, it isideally suited for woodworking, wood-turning, sharpening, sculpting and gardening. Inside breast pocket, adjustable shoulder straps.90 x 60 cm

M -CAPThis stylish cap will protect you fromwood shavings and dust in the workshopas well as unseasonable conditions out-doors. Comfortable, 100% cotton capembroidered with our logo. With adjustable Velcro strap.

N PROHANDS® CUT-RESISTANT GLOVES

SizeS No. 707650 15.04 € 17.90 € M No. 707651 15.04 € 17.90 € L No. 707652 15.88 € 18.90 € XL No. 707653 16.13 € 19.20 € XXL No. 707654 16.72 € 19.90 €

O FINGER PROTECTORS, 3-PIECE SETFastened to the fingers with elasticatedstraps, these leather finger protectorsprotect you from injury when workingwith sharp tools, sewing, cultivating thor-ny plants, and many other uses. They arealso ideal for protecting your fingers ifyou have cut them. Set includes pro-tectors for two fingers and one thumb.

For more traditional Japanese clothing see www.more-than-tools.de

F

G

H

E

N

A

B

C

D

I

J

K

O

L

M

Magnetic tool bar for light to mediumweight tools. Powder-coated steel railwith plastic body.500 x 40 x 25 mm

E ROLLER BALLS, 6-PIECE SET

Soft-touch winter socks with traditionalseparate big toe. Can also be worn withJika-Tabi. Blended fabric of 55% acrylic,30% cotton and 15% nylon. One size, black.

Leder- und Papierwerkzeuge || Blindtext

157

Leather-working tools | 158

Leather care | 160

Paper-working tools | 160

Leather- and paper-working tools || Leather-working tools

158

Leather-working tools

A STITCH MARKERElegant stainless steel tool with brasshoop and betula wood handles formarking seams. Thanks to the bentshaft, the stainless steel wheel canbe moved ergonomically and marksstitches every 4 mm.Length 145 mmNo. 708326 75.55 € 89.90 €

M THONGING CHISELSHigh-quality Japanese chisels for mark-ing and punching holes. Diamond-shapedprongs at a 45° angle. Prong spacing 5 mm1 1 prong No. 717209 4.87 € 5.80 € 2 3 prongs No. 717207 16.72 € 19.90 € 3 6 prongs No. 717208 31.85 € 37.90 €

B SEWING HOLSTERGuard with metal insert for pushingneedles through leather, thick fabric andfelt. Strong leather, riveted. Right-handed.55 g.No. 708300 16.72 € 19.90 €

E AWL ASSORTMENT

No. 708302 3.70 € 4.40 €

D AWL HANDLEClamping handle with knurled ferrule.Beech handle.Length 95 mmNo. 708301 10.50 € 12.50 €

For more linen threads seewww.more-than-tools.de

C HALFMOON KNIFEThe traditional saddler's knife with awide, semicircular blade allows the knifeto be guided at a right angle even whencutting thick leather. Long, exact cuts aremade with the middle of the blade, tightcurves with the tips. Also used for thinn-ing out leather. Handle made from oilednative cherry wood, with brass ferrule.Blade width125 mm No. 701366 81.93 € 97.50 € 150 mm No. 701367 83.95 € 99.90 €

L FRENCH LEATHER SCISSORSThese professional saddler's shears easilycut through leather up to 4 mm thick.The serrated edge on the lower blade prevents the material from slipping. Thehook-shaped form can be used for mark-ing and creasing. Also suitable for rubb-er, heavy cardboard, soft plastic etc.Overall length 220 mmBlade length 80 mm270 gNo. 708146 75.55 € 89.90 €

I JAPANESE LEATHER CHISELFor cutting and trimming leather andcardboard. Single-bevel blade made of double-layer steel. Magnolia handle.Overall length 185 mmBlade length 65 mmBlade thickness 2 mmWidth 36 mmNo. 710714 10.84 € 12.90 €

J JAPANESE LEATHER KNIFEWide, curved blade made of double-layersteel with wrapped handle. Right bevel.Length 195 mmWidth approx. 25 mmNo. 710532 25.13 € 29.90 €

K BEVEL KNIFESingle, right-bevelled and slightly curvedknife for skiving (trimming) leather edges.Thickness 2 mm260 x 22 mmNo. 704564 16.72 € 19.90 €

H REVOLVING PUNCH PLIERSFor punching leather, cardboard, rubber,plastic etc. With six punches with diame-ters of 2/ 2.5/ 3/ 3.5/ 4 and 4.5 mm.The diameter is displayed in the viewwindow. Pressed, anti-skid corded steelshanks with stop.Length 210 mm270 gNo. 711995 12.02 € 14.30 €

N COMMON EDGE TOOLFor bevelling and roundingoff leather edges. Each toolis ground by hand andtested. Stained maple handle.Length 135 mmBlade width4.0 mm No. 708309 30.17 € 35.90 € 4.8 mm No. 708325 30.17 € 35.90 €

HANDBUCH LEDERARBEITENBy Valerie Michael. Introduction to thefascinating world ofleather crafting. Thebook presents materi-als, tools and basictechniques. 128 pages, 178 photographs, some in colour, hardcover, 210 x 260 mm, in German.No. 713130 36.36 € 38.90 €

O CURVED LEATHER PLANEFor tapering (thinning) leather edges. Replaceable blade.Overall length 170 mmBlade 40 mmNo. 708306 11.51 € 13.70 €

No. 708307 10.50 € 12.50 €

P FOLDING BONEFolding bone for smoothing seams, fold-ing and polishing leather edges as well asfolding paper. Buffalo bone.180 x 20 x 5 mmNo. 708305 9.41 € 11.20 €

No. 709025 3.28 € 3.90 €

1 Linen thread, blackThickness 0.8 mmLength 30 mNo. 831402 4.45 € 5.30 €

2 Linen thread, beigeThickness 1.2 mmLength 25 mNo. 831405 5.29 € 6.30 €


A D

I

J

K

M

P

N

O

E

C

B

H

L

1 2

F

G

Stabbing awl, curved sewing awl and stit-ching awl. Fits awl handle No. 708301.

1

2

3

F LINEN THREADUnwaxed linen thread for hand-stitchedseams in leatherwork. Is usually drawnthrough beeswax before use.

G LINEN THREAD, WAXEDThanks to its waxed surface, this smoothlinen thread is water-resistant and keepsits shape.Thickness 0.8 mmLength 10 m

Leather- and paper-working tools || Leather-working tools

159

A LEATHER DRILL PUNCHJapanese drill-actionpunch awl for cuttingclean holes in leather,plastic and cardboard. Verysharp, hardened cuttingheads. Brass shank, beechhandle.

1 Leather drill punch,6-piece standard setSet: Ø 1.5 / 2.5 / 3 / 3.5 / 4 mmNo. 716156 25.13 € 29.90 €

2 Leather drill punch,10-piece professional setSet in wooden case: Ø 1.5 / 2 / 2.5 / 3 /3.5 / 4 / 5 / 6 / 8 mmNo. 716159 45.29 € 53.90 €

E SHOEMAKER’S HAMMERWell-balanced slim hammer with a rounded face, slim pane and ergono-mically shaped ash handle.Head weight 300 gLength 260 mmNo. 705687 16.72 € 19.90 €

F MAGNETIC TACK HAMMER

From above, this hammer resembles ahorseshoe magnet because of its splitend, which provides a stronger magneticforce than a design with a round magnet.The split magnetic end allows you to po-sition tacks safely and easily, while thestriking face is used to drive them in.Head weight 140 gLength 280 mmNo. 708310 43.61 € 51.90 €B HOLE PUNCHES,

8-PIECE SET

No. 708329 55.38 € 65.90 €

Price advantage

Individual hole punches available atour online shop: www.more-than-tools.de

D ORNAMENTAL PUNCHES, 18-PIECE SET

18-piece punch set with different patt-erns for decorating leather and woodensurfaces. Punches can also be heated forbranding. Tool steel.11 x 11 x 68 mmNo. 708311 21.76 € 25.90 €

G STRAP CUTTER

No. 708327 26.81 € 31.90 €

No. 708338 4.96 € 5.90 €

For more leather-working tools seeour webshop at www.more-than-tools.de

H LEATHER-SKIVERWhether you want to split or skive piecesof leather, this mechanical leather-skiverwith its hardened blade makes the taskmuch easier. Based on the patentedOsborne 84 model, this machine willimpress you with its ultra-solid con-struction. A swivel handle lets you safelyadjust the roller precisely to the thick-ness of the leather. If required, you canlock it in position with a stop. A brassretainer helps you insert the leather andprevents premature splitting. Two Allenhead srews allow you to convenientlyadjust the blade or remove it for sharpe-ning.305 x 150 x 245 mmCutter width 20 mm6.2 kgNo. 708328 553.78 € 659.00 €

A

B

D

G

H

E F

1

2

Replacement cutter

C HOLE PUNCH SET WITH CIRCLE CUTTER, 19-PIECE SET

No. 708344 100.76 € 119.90 €

CThis wooden strap cutter cuts leatherstraps up to 100 mm wide The leather isguided through the continuously adjusta-ble clamping bars and cut with a cutterwhich is easy to replace.205 x 165 mmMax. thickness of leather 7 mm

High-quality punches made in Germanyfor making holes in leather, cardboard,plastic etc. From special steel, drop-forged, stove-enamelled. 8-piece set in a roll-up case.Ø 3 / 6 / 8 / 10 / 12 / 16 / 20 / 25 mm

Hole punch set consisting of chrome-pla-ted handle, 15 punch blades of differentdiameters, a spring-loaded centering tipand a circle cutter. The small blades arescrewed onto the handle, while mediumblades (small base) and large blades(large base) are inserted and snap on.This makes it easy to cut rings of diffe-rent diameters and punch accurateholes. The circle cutter with hardened tip(68-70 HRC) allows you to cut holes ofup to 160 mm diameter. Blade Ø 3, 4and continuing at 2 mm intervals up to30 mm. Burnished blades, chrome-pla-ted handle.Handle length 120 mm

For cutting paper, cardboard, foil andthin fabrics. Rotating blade, ergonomicaluminium handle.Blade Ø 45 mm (thickness 0.3 mm)Overall length 150 mm

Leather- and paper-working tools || Leather care, Paper-working tools

160

Leather care

A RAPIDE® LEATHER CARE PRODUCTSHigh-quality products for the preserva-tion and care of leather. Primarily basedon vegetable oils and waxes, these pro-ducts are environment-friendly, non-aller-genic and in perfect harmony with thenatural product leather.

For the deep impregnation of smooth andthick leather. Soaks in well, keeps theleather moist and protects it from waterand dirt. Free of solvents, pleasant smell,uncoloured.Contents100 ml No. 820142 3.87 € 4.60 € 1000 ml No. 820143 9.66 € 11.50 €

4

For durable protection and preservationof all smooth leather products such assaddles, boots, seats, bags and backpacks. Applied with a cloth or brush,it soaks into the pores of the leather andkeeps it supple. Free of solvents, pleasant smell, uncoloured.Contents150 ml No. 820145 4.12 € 4.90 € 1000 ml No. 820146 8.32 € 9.90 €

1

Milky emulsion for cleaning and impreg-nating all kinds of leather, even reindeerand elk leather. Keeps the leather flexi-ble, humid and renders it water-repellent.Content250 ml No. 820140 6.64 € 7.90 € 1000 ml No. 820141 19.24 € 22.90 €

3

C LEATHER BALM EQUIFIX®

Without care, leather products soon be-come dry and brittle. This resin and acid-free leather balm with beeswax makesleather supple, tear-resistant and impreg-nates it very effectively.500 gNo. 820148 6.22 € 7.40 €

Vaseline should always be at hand as anall-purpose cream for protecting dry skinpreserving leather, but also as a lubricantand anti-rust agent. White Vaseline byRapide is a pure paraffin product, freeof aromatic hydrocarbons and otherharmful substances.150 mlNo. 820147 3.61 € 4.30 €

B SADDLE SOAP (GLYCERINE SOAP)Due to its high content of moisturisingglycerine, this saddle soap is ideal forcleaning all kinds of leather items with-out drying them out. Rub well with asqueezed sponge or cloth.250 gNo. 820144 5.46 € 6.50 €

A

I

D BALLISTOL® PLUVONINIMPREGNATION SPRAYPluvonin is a highly effective spray for im-pregnating all textiles and napped leather,based on nanotechnology. It is ideal forweatherproofing outdoor clothing as wellas backpacks, tents, maps, sails and um-brellas. This product is hydrocarbon-freeand does not damage the ozone layer.200 mlNo. 705442 3.87 € 4.60 €

C

B

Paper-working tools

J GLUE FOR SHOJI PAPERStarch-based liquid glue,especially suited for Shojipaper. Dosing spout with stopfor accurate application toShoji rungs.150 mlNo. 715990 2.35 € 2.80 €

I FOLDING BONEFolding bone for smoothing seams, fold-ing and polishing leather edges as well asfolding paper. Buffalo bone.180 x 20 x 5 mmNo. 708305 9.41 € 11.20 €

H MAT CUTTERFor 45° and 90° cuts.V-shaped, sharpenedblade for cutting cleanedges. Plastic bodywith 2 blade holdersand 5 double-sidedblades.No. 708090 11.68 € 13.90 €

No. 708091 4.62 € 5.50 €

F ALUMINIUM GUIDE RAIL FOR MAT CUTTERWith groove for the mat cutter (No.708090), slip-proof and with scale mar-kings.Length 600 mmNo. 708092 10.00 € 11.90 €

Cutting rules are to be found in chap-ter measuring and inspection instruments.

E CUTTING PADElastic, slip-proof pad with printed gridand »self-repairing« surface. Can also beused as a base for writing and drawing.With imprinted grid.450 x 600 mmNo. 708093 13.36 € 15.90 €

G PAPER CUTTER

No. 710536 8.99 € 10.70 €

No. 710537 2.77 € 3.30 €

SHOJI - DO-IT-YOURSELF SLIDINGDOORS, DIVIDING WALLSMasterpieces of Jap-anese Craft Culture,by Toshio Odate. explains how to makea Japanese slidingdoor, from layout togluing on the paper.Having been trainedhimself as a tategushi,or sliding-door maker,in Japan, he gives insight into this traditional craft withgreat expertise and explains the process comprehensibly. 120 pages, 217 b/wphotographs and 51 drawings, softcover,210 x 280 mm. In English.No. 713470 18.60 € 19.90 €

H

G

F


2

D

E

J

4 Rapide® leather oil

1 Rapide® leather cream

3 Rapide® leather dressing

2 Rapide® white vaseline

Replacement blade

Smoothing and polishing material | 163

Surface protection and colours | 166

Oils | 166

Waxes | 167

Resins | 168

Powders and pigments | 168

Brushes | 168

Glues and glue pots | 169

161

Bringing out the beauty of wood!

Adhesive force

Cohesive forcesGlued joint

Finishing

162

SURFACE FINISHING

Finishes

What could be more natural than using the

finishes provided by nature to protect your

wood? For thousands of years, vegetable oils,

waxes and resins have proven their value for

preserving wood and emphasising the grain.

They are environ-

mentally friendly

and easy to apply.

We offer these sub-

stances in their pure

form. For suggestions

for their use and how

to make tried-and-

tested mixes, see

our »Surface

Primer«, available on

our website. In this

way, you’ll always

know »what's in

them«.

Workshops

French Polishing

Wood Polishing

Gilding

Shellac for Turners

Veneering

Glues

For over 4000 years, vegetable and animal

glues have been used for bonding wood and

other materials. The number and variety of

glues available today is vast - from traditional

reversible vegetable and animal glues, to

polyvinyl acetate glue (normal PVA glues) and

waterproof, foamy polyurethane glues, right

through to two-component adhesives. Nearly

all applications require a special adhesive,

and the individual glues differ too much in

their use to show in detail here. However, one

essential factor, which also determines the

durability of the glued joints, is always the

same: the preparation of the surfaces.

Correct preparation of the surfaces to be glued

The mechanism of sticking and bonding is

based on the interaction of two key factors:

adhesion and cohesion, which we explain

briefly below.

The figure shows a close-up view of the glued

joint. The marked forces are divided into

adhesive forces and cohesive forces.

The adhesive force is the force which holds

together the atoms or molecules of different

bodies (in our example wood and glue).

Cohesive forces are forces which hold together

the atoms or molecules of the same body.

In our case, this is the cohesion of the glue

particles among themselves.

Influencing cohesion

You cannot really influence the cohesive

force itself significantly; it depends on the

type of glue and how it was made. Of course

you should always observe the correct blend-

ing and not exceed the use-by date. What you

can influence is the accuracy of fit of the

parts to be joined and the resulting distance

between the glued surfaces. If the glued joint

is »wider« than 0.2 mm, the forces in the

joint are significantly reduced. For the best

result, the wood surfaces should be glued

quickly after creating the joint. If you wait

too long, the exactly fitting jointing surface

may warp slightly due to varying humidity,

and in the case of oily woods such as teak,

oil may leak, preventing a clean contact

surface.

Influencing adhesion

Adhesion you can influence directly, e.g.

by making sure the jointing surfaces are clean

and free of grease. The glue cannot stick

to a surface that is tainted by greasy or oily

substances. To avoid this, it is recommended

that you wipe the surfaces to be glued with

acetone or alcohol. Another crucial factor is

the application of the glue, which must be

thin and even. If the glue is not applied

evenly, the bonding forces between the wood

and the glue are lacking at some points,

which reduces the bonding strength of

the entire glued joint.

Finishing || Smoothing and polishing material

163

Smoothing and polishing material

Emery clothFlexible and sturdy:Thin, very efficient emery cloth fromJapan, ideal for the perfect grinding ofwood, paint and metal. It stands out byits rapid action and wear endurance. Thelinen backing makes it extremely flexible,so it matches up to the finest profiles.

Hartmut Münzberg,master violin maker:»For retouching varnishies or inter-mediate sanding in varnishing, the abrasivecloth must be flexible,evenly abrasive andhighly wear-resistant. I am enthusiastic about Kovax abrasivecloth from Japan.«

A KOVAX® FLEX CLOTH SHEETSPacks of 10 sheets230 x 280 mmGritP 120 No. 704974 10.59 € 12.60 € P 180 No. 704975 10.59 € 12.60 € P 240 No. 704976 10.59 € 12.60 € P 320 No. 704977 10.59 € 12.60 € P 400 No. 704978 10.59 € 12.60 € P 600 No. 704979 10.59 € 12.60 € P 1000 No. 704980 11.51 € 13.70 €

B KOVAX®, IN ROLLS

GritP 80 No. 704981 39.92 € 47.50 € P 100 No. 704982 38.15 € 45.40 € P 120 No. 704983 35.55 € 42.30 € P 180 No. 704984 35.55 € 42.30 € P 240 No. 704985 35.55 € 42.30 € P 320 No. 704986 35.55 € 42.30 € P 400 No. 704987 35.55 € 42.30 €

A

C SANDING AIDSanding large surfaces made easy: Thin steel plate with foam rubber coatingand stable handle of cushioned redbeech. The abrasive cloth is fastened tothe grinder with two practical terminalclamps.Base plate 90 x 185 mmNo. 705125 11.34 € 13.50 €

D SUEHIRO® SANDING BLOCKJapanese handsander with durableand effective self-adhesive sanding pads (Velcro coated).Incl. 3 pads.Grit 80 / 120 / 320115 x 55 mmNo. 705120 6.97 € 8.30 €

Replacement padsEach 5 pcs.115 x 55 mmGrit80 No. 705121 4.12 € 4.90 € 120 No. 705122 4.12 € 4.90 € 240 No. 705123 4.12 € 4.90 € 320 No. 705124 4.12 € 4.90 €

G HEGNER® HSM 300 DISCSANDING MACHINERock solid, versatile sanding machineby Hegner, the Black Forest precisionmachine company. Changing the Ø 300mm sanding discs on the plate is simple,thanks to Velcro fastening.The 520 x 260 mm anodised aluminiumtable provides secure support for theworkpiece. It extends behind the sandingdisc on both sides, so inside edges toocan be easily worked on. The table canbe tilted continuously up to 45 degreesincline, a mitred limit stop with scalingand locking handle enables precise ad-justments for angular cuts and series.With extraction connector, Ø 58 mm.Sturdy aluminium housing in green,hammered varnish.0.75 kW motor with undervoltagerelease and 3 m cable.230 V1400 RPM25 kgNo. 704810 549.58 € 654.00 €

Hegner® sanding discs for woodWith Velcro coating, 5 discs each, forDisk Sanding Machine 704810.Ø 300 mmGrit60 No. 704826 20.92 € 24.90 € 80 No. 704827 17.56 € 20.90 € 120 No. 704829 17.56 € 20.90 € 240 No. 704830 20.00 € 23.80 € 320 No. 704831 20.00 € 23.80 €

Grit60 No. 704835 23.45 € 27.90 € 100 No. 704837 21.51 € 25.60 € 120 No. 704838 21.51 € 25.60 €

E JAPANESE ABRASIVE AND POLISHING CLOTH, 16-PIECE SETIdeal for wet or dry, fine and intermediatesanding of wood or metal surfaces of anyshape. The wavelike distribution of thesanding particles results in particularlyhigh efficiency and leaves a uniform surface pattern. The soft, highly flexiblegrinding fibre is fixed to a practical handpad by means of a Velcro fastener andcan be brushed orwashed after use.5 double sheets170 x 130 mm ofeach grit 600,800, 1500, 1 hand pad 75 x 120 mmNo. 704966 33.53 € 39.90 €

B

C D E

G

F JAPANESE CORK SANDING BELTSParticularly for knife makers:

Grit120 No. 704103 18.40 € 21.90 € 180 No. 704104 18.40 € 21.90 € 240 No. 704105 18.40 € 21.90 € 400 No. 704107 18.40 € 21.90 € 600 No. 704108 18.40 € 21.90 €

F

(One roll)100 mm x 15 m

These belts, in which the sanding particlesare applied to a thick layer of cork, areused in Japan by leading manufacturers ofknives and shears to produce their leg-endary hollow grinding and high-qualityfinishes. They are watered before sanding.The belts respond more elastically thanconventional textile belts, delivering con-cave surfaces with considerably fewer visi-ble ghost lines.3 pcs. per pack.50 mm x 2 m

Hegner® sanding discs for metalWith Velcro coating, 3 discs each, forDisk Sanding Machine 704810.Ø 300 mm


164

Micro-Mesh® abrasive and polishing clothThe finest quality smoothing and polishing material:MicroMesh is excellent for intermediatesanding between coats of paint, retouch-ing and fine finishing work on wood,plastic, plexiglass and metal surfaces, including polishing, on irregular andcurved surfaces in particular. The abra-sive particles are suspended in a siliconmatrix firmly bound to a thin, highly flexible textile basis, so that no residuesremain on the finished surface. MM can be used dry, with water, or with petroleum, and is very long-lasting under normal wear.

Grit1500 No. 705101 2.18 € 2.60 € 1800 No. 705102 2.18 € 2.60 € 2400 No. 705103 2.18 € 2.60 € 3200 No. 705104 2.18 € 2.60 € 3600 No. 705105 2.18 € 2.60 € 4000 No. 705106 2.18 € 2.60 € 6000 No. 705107 2.18 € 2.60 € 8000 No. 705108 2.18 € 2.60 € 12000 No. 705109 2.18 € 2.60 €

Assortment, 11-piece1 sheet each of grit 1500, 1800, 2400,3200, 3600, 4000, 6000, 8000, 12,000,1 polishing file, 1 grinding block.No. 705115 20.08 € 23.90 €

Price advantage

Assortment, 20-piece2 sheets of each grit 1500, 1800, 2400,3200, 3600, 4000, 6000, 8000, 12,000,1 polishing file, 1 grinding block.No. 705116 33.53 € 39.90 €

Precise and easy to use for intermediategrinding, polishing and varnish repairs.Elastic foam core coated on both sideswith abrasive cloth.100 x 75 x 5 mmGrit1500 No. 705411 1.68 € 2.00 € 1800 No. 705412 1.68 € 2.00 € 2400 No. 705413 1.68 € 2.00 € 3200 No. 705414 1.68 € 2.00 € 3600 No. 705415 1.68 € 2.00 € 4000 No. 705416 1.68 € 2.00 € 6000 No. 705417 1.68 € 2.00 € 8000 No. 705418 1.68 € 2.00 € 12000 No. 705419 1.68 € 2.00 €

Assortment, 9-piece1 soft pad in each grit 1500, 1800,2400, 3200, 3600, 4000, 6000,8000, 12000.No. 705420 13.53 € 16.10 €

Ideal for varnish repairs. Flexible, filecoated on both sides with grits 3200,6000, 12,000.145 x 12 mmNo. 705110 1.85 € 2.20 €

E SANDING BLOCKMade of foam.70 x 45 x 23 mmNo. 705114 1.93 € 2.30 €

F MICRO-MESH® MX, 7-PIECE SETThe coarser grit of Micro-Mesh® MX isdesigned for rapid sanding. Well suited forsmoothing varnished surfaces, workinghard materials (metal, stone, hardplastics), cleaning oxidised or stainedsurfaces, removing scratches, and forsharpening and polishing. MX is lessflexible than MM due to the somewhatstiffer textile base used.Single sheets (153 x 82 mm).Grit 60/100/150/240/360/600/1200No. 705481 13.78 € 16.40 €

G STICK SANDERFile-like sanding stick for detail applica-tions in model making, instrument makingetc. Incl. 1 high-quality textile sandingbelt, grit 240.6.5 x 160 mmNo. 705430 4.62 € 5.50 €

Sanding belts for VariolapperSets of 3.Grit120 No. 705431 3.11 € 3.70 € 180 No. 705432 3.11 € 3.70 € 240 No. 705433 3.11 € 3.70 € 320 No. 705434 3.11 € 3.70 € 400 No. 705435 3.11 € 3.70 € 600 No. 705436 3.11 € 3.70 €

I POLISHING AND CLEANING FABRICIdeal material for a rubbing pad forFrench polishing as well as for cleaning,polishing and the careful packing of sen-sitive parts. Finely woven tubular fabricmade of tough, lint-free, terry-cloth-likecotton, does not fluff.20 mNo. 810008 33.53 € 39.90 €

H MICRO GLOSS® POLISHEliminates the finest scratches:Micro Gloss is a water-based polish con-taining aluminium oxide particles 1 µmin size for finely polishing acrylic, metal,wood and hard varnishes. It completelyremoves the visible scratches left byMicro Mesh® and leaves a brilliantlyglossy finish. Does not discolour.55 gNo. 705482 5.29 € 6.30 €

Proper, gentle polishing

Thoroughly clean the surface first,then lightly dampen. Apply MicroGloss® to a lint-free cotton cloth andpolish the surface in straight strokesuntil the Micro Gloss is used up.When polishing larger surfaces, work25 cm at a time, overlapping somewhat as you go.

A

F

Price advantagePrice advantage

C

D E G

I

H

Grit1500 No. 705311 58.74 € 69.90 € 1800 No. 705312 58.74 € 69.90 € 2400 No. 705313 58.74 € 69.90 € 3200 No. 705314 58.74 € 69.90 € 3600 No. 705315 58.74 € 69.90 € 4000 No. 705316 58.74 € 69.90 € 6000 No. 705317 58.74 € 69.90 € 8000 No. 705318 58.74 € 69.90 € 12000 No. 705319 58.74 € 69.90 €

B

A MICRO-MESH® SINGLE SHEET153 x 82 mm

B MICRO-MESH® ROLLS153 mm x 3 m

C MICRO-MESH® SOFT PADSAdapt to all shapes:

D MICRO-MESH® POLISHING FILE

For tight spots For flat surfaces For rounded surfaces


Kirjes®-sanding systemPerfect finish to any shape in wood:The quality and perception of any pieceof work is largely influenced by itsfinish. Flat surfaces can easily befinished with a smoothing plane orsand paper. However concave or convexshapes, the inner surfaces of rectanglesand irregular shapes are much moredifficult. So far a machine finish wasnot possible while a hand surface wasextremely time consuming. This gap hasnow been closed by the Swedish manu-facturer Kirjes with its integrated sandingand polish system.

A sleeve of highly flexible abrasivecloth is fitted on a cylindrical or dome –shaped rubber bulb which is then in-flated with a special hand pump throughan air valve on the shaft.Such pneumatic sanding cages arevery elastic, perfectly conforming to anyshape. In addition to sanding sleeves,brush sleeves for polishing are also onoffer. They will give your work a polishedsurface. All inflatable sanding cages arefixed to the drill chuck of a 130 cmflexible shaft. The perfect tool for innersurfaces of carved and curved objects,for hard to reach areas, spoons, musicalinstruments, sculptures, ornaments,wooden toys, knife handles...

No. 707437 277.23 € 329.90 €

B SANDING & POLISHING MOTOR Powerful and silent motor, equippedwith two scroll drill chunks 0-10 mm.350 W230 V3000 RPM4.5 kgNo. 707432 109.16 € 129.90 €

A

C FLEXIBLE SHAFTHighly flexible, equipped with threecapsuled ball-bearings and key chuck0-10 mm. Intended for low-speed use (ca.3000 RPM), max. speed 10,000 RPM.Length 130 cmNo. 707433 67.14 € 79.90 €

F DRUM SANDING KIT NO. 100

No. 707435 120.92 € 143.90 €

For more Kirjes products see our webshop at www.more-than-tools.de

B

C

F

E BASIC SANDING KIT

No. 707436 83.95 € 99.90 €

D EXTRACTOR HANDLE

No. 707434 33.53 € 39.90 €

D

E

Set includes:1x drum sander Ø 20 x 321x drum sander Ø 28 x 801x drum sander Ø 42 x 441x dome sander Ø 42 x 354 x 3 sanding sleeves grit 80, 150, 320hand pump

Set includes:1x drum sander Ø 42 x 441x dome sander Ø 42 x 352 x 4 sanding sleeves grit 80, 150, 220, 320, hand pump, cleaning stick

This extractor handle is made to vacuumfine saw dust produced with the Kirjes-System right at the point of formation.The flexible shaft with connection piece(Inner-Ø 32 mm) is easily fitted on anyconventional vacuum cleaner.

G POLISHING BRUSH SLEEVES The Kirjes brush attachment is used foreven distribution of waxes on fibrous andporous surfaces. You can also use it tobuff the first wax layers when they are dry.

1 cylindric Ø 20 x 32 mm2 pieces.No. 707418 3.28 € 3.90 €



4 ball shaped Ø 42 x 35 mm1 piece.No. 707421 6.13 € 7.30 €

H POLISHING CLOTH SLEEVES These polishing cloth sleeves are usedfor the final polishing of dried wax layers.2 pieces.

1 cylindric Ø 20 x 32 mmNo. 707422 3.28 € 3.90 €




165

G1

2

3 4

H1

2

3 4

Kirjes natural oil wax (No. 705356)see page 167.

A KIRJES®-SANDING SYSTEMComplete sanding system includingmotor, flexible shaft, sanding cage setNo. 100, English manual and DVD.

Finishing || Surface protection and colours

166

Surface protection and colours

Oils

A SINENSIS® CAMELLIA OILVersatile, light oil fromthe seeds of the ca-mellia tree:Corrosion protection:Camellia oil is acid-free, not volatile andnot susceptible to resinification, makingit the ideal oil to protect tools from rust.Made from pure natural plant productsand food safe, it is especially suited forthe preservation of kitchen knives madeof carbon-steel.Wood protection: When applied to woo-den surfaces, it is absorbed quickly dueto its low viscosity. Once absorbed, ithelps protect the wood from damage bymoisture, dirt and UV light. Clear, notdiscolouring, it accentuates the wood’snatural beauty. Non-hardening.Body care: Camellia oil makes an excel-lent base for the preparation of lotions,creams and soaps for cosmetic use.

Content1 100 ml No. 705280 3.45 € 4.10 € 2 250 ml No. 705281 5.21 € 6.20 € 3 1000 ml No. 705282 11.43 € 13.60 €

Cold-pressed from lin-seeds, this hardeningoil is for the ecologicalprotection of wood.Highly transparent,chemical-free andfood safe with only minimal odour.Linolja can be used directly in its pureform. It is also suitable for producing lin-seed-oil paint (with iron-oxide pigment),as well as mixed with tar oil for use onexteriors.

1 Linolja®, sun-bleachedParticularly bright and colour-true. Pre-oxidized by careful bleaching in the sunand thus dries faster.Content1000 ml No. 705275 15.04 € 17.90 € 5000 ml No. 705269 58.74 € 69.90 €

2 Ra Linolja®, rawUntreated linseed oil, a pure natural pro-duct, dries slowly so penetrates deep intothe wood, polishes well.Content1000 ml No. 705354 7.48 € 8.90 € 5000 ml No. 705355 29.58 € 35.20 €

D LIGNEA® - CHINESE TUNG OILHigh-quality natural oil for indoor and outdoor use:Lignea, the oil obtai-ned from the fruits ofthe Chinese tung tree(Aleurites fordii), hasmany uses both in-doors and out, e.g. forindoor and outdoorfurniture, decks, flooring, turned items,musical instruments, wooden toys andwooden boats and can be used for im-pregnating fabrics and even masonry.Tung oil is absorbed by wooden surfacesvery quickly and hardens them after ithas dried, making them mechanicallystronger and highly water-resistant. Itprovides approximately twice as muchprotection as linseed oil. It deepens col-ours and enhances the contrast of thegrain, but the wood retains its natural vi-sual and tactile characteristics. The pro-tective film is elastic, even in the longterm, and, in contrast to linseed oil, dar-kens very little. If the finish becomes dam-aged, it can be easily retouched byrubbing more oil over the damaged area.Lignea can be applied without anyproblems, even in multiple coats, usingeither a brush or a piece of cloth, andcan be thinned with turpentine or mixedwith other vegetable oils (e.g. linseed orcamellia oil) depending on the user’spreference.

Content1000 ml No. 705286 17.56 € 20.90 € 5000 ml No. 705283 61.68 € 73.40 €

A

Examples of possible mixtures can be found in our brochure titled»Oberflächenfibel«, which you can down-load free of charge on the Internet at www.more-than-tools.de

On oiled surfaces, the wood grain, andabove all the contrast between longi-tudinal and transverse wood, is clearlyaccented. Here is an ash table top byCharles Beresford with tenons mor-tised through, shellac priming + twolayers of tung oil with 10% orange oil.

C POPPY-SEED OILColour-true:Food safe oil extracted from the seeds ofthe white poppy flower (Papaver somnif-erum) is ideal for fine craftwork objects,turned parts, toys, kitchen furniture andkitchen utensils. Because of its good gripit is suitable for knife and tool handlesand, along with pigments, for making valu-able paint oils and artists’ colours. Thehigh transparency of poppy-seed oilmakes it the perfect base for violin var-nishes and clear protective wood fin-ishes. It provides excellent protectionagainst moisture and dirt, does not yel-low, and penetrates deeply into the wood.Poppyseed oil dries much slower thanlinseed oil. Multiple coats of poppy-seedoil yield a warm, silky gloss and a surfacewhich is pleasant to the touch. Poppy-seed oil can be mixed with other vegeta-ble oils and solvents.Content1000 ml No. 705272 13.36 € 15.90 € 5000 ml No. 705268 61.68 € 73.40 €

Drying oils (e.g. tung oil, linseed oil) not only protect the surface from contamina-tion, but also harden the layers of wood near the surface. The lower their viscosityand the more slowly they dry, the deeper they penetrate (so priming should alwaysbe diluted 20% to 50%).

Tips: Tung oil in both its pure and liquidform has a distinctive smell that disappearsafter drying or when mixed with eitherorange oil or balsam oil of turpentine. Be-cause of its odour, we do not recommendit for cupboard interiors. The tung oil of-fered here is ecologically sound. It is notpre-oxidized, nor is it mixed with chemicaldrying agents. Consequently, it takes up totwo days to become dry. (Drying times varyconsiderably depending on the environ-mental conditions, type of wood and pre-paration of the surface.) Once dry, the oil'sfilm is chemically stable and free of dan-gerous emissions. Pure tung oil is rela-tively viscous, but its ability to penetratecan be improved by thinning with balsamoil of turpentine (No. 705288) or by warm-ing.

1 2 3

B

1

2

D

C

B LINOLJA® ORGANICSWEDISH LINSEED OIL


167

A PURE ORANGE OILNatural diluting and cleaning agent:Low-viscosity orange oil from the peelof the sweet orange, ideal for thinningvegetable-based protective wood oils,and its grease dissolving properties makeit a useful household cleaner. Mixing10 - 20% of it with a linseed or tung oilfinish markedly improves penetration,facilitates application and lends theseoils a refreshing aroma. In combinationwith carnauba wax or beeswax it canmake a variety of agents for cleaningand caring for wooden surfaces, antiquesand leather. Orange oil is also suited foruse as aromatic oil.

Content 1 250 ml No. 705277 6.64 € 7.90 € 2 1000 ml No. 705278 15.04 € 17.90 €

B TURPENTINE OILSolvent with ethereal aroma:

1

A

C SWEDISH PINE TAR One of the oldest wood preservatives,ideal as paintwork for houses, shingles,fences, equipment, sleds and boats. Thiswood tar oil obtained by the pyrolysis andcareful distillation of resin-rich pine root-stock is moreover the ideal material foraxe and tool handles, because it lets thewood breathe and improves its grip. Be-cause of its long drying time, it pene-trates deep into the wood, lends it abeautiful patina, and gives it lasting pro-tection against the effects of weather.The relatively viscous Furutjara can bediluted with turpentine oil or linseedoil. Because of its strongly smoky aroma,we only recommend it for use outdoors.

1 Furutjära® pine tarViscous black wood tar for optimum pro-tection against UV radiation and other ef-fects of the weather.Content1000 ml No. 705347 10.42 € 12.40 € 5000 ml No. 705349 43.95 € 52.30 €

untreated treated with Furutjära® treated with Dalbränd Tjära®

2 Dalbränd Tjära® fine pine tarThis high-quality wood tar is somewhatlighter and thinner than Furutjära pinetar and emphasises the grain more.Content1000 ml No. 705351 16.39 € 19.50 € 5000 ml No. 705352 63.03 € 75.00 €

Waxes

D PARAFFIN WAXColour-true and water-resistant:Transparent wax for sealing cross-grainedwood surfaces, for application while turn-ing on a lathe, for mixing with beeswax,as preservative protection for wood andmetals, and for lubricating sliding matingparts. Extracted from mineral oil, colour-less and odourless, solvent-free andhighly water-resistant.

G CARNAUBA WAXThe hardest wax:For particularly wear resistant, glossyfinal polishing. Can also be used as alubricant for sliding wooden parts andas corrosion protection for metal surfaces.The wax of the Brazilian carnauba palmis distinguished by its great hardness and good physiological compatibility. The wax offered is unbleached and has amelting point of approx. 90°C. Suggested recipe for wax polishing paste:carnauba wax/beeswax/oil of turpentine:1/2/2.Weight500 g No. 810009 9.83 € 11.70 € 1000 g No. 810010 13.11 € 15.60 €

Propolis, a plant resin collected byhoney-bees, makes paints and oilssmoother and longer-lasting, and lends tothem an agreeable aroma. With its disin-fecting effect, propolis prevents bacterialor fungal attack without displaying phys-iologically questionable side effects.Ideal for treating wooden parts that con-tact the skin, such as cooking utensils,breadboards, sauna and bath furniture,and children's toys. The resin offeredmay either be directly dissolved in paint-work or oil or be further processed withhigh-percentage spirits in a liquid con-centration. Recipes are enclosed.

H - HOLZBALSAM (WAX FOR PRESERVING WOOD)Through and through natural:Contains a high percentage of all-naturalbee wax. HolzBalsam contains pure natu-ral ingredients which preserve the wood.It is free of chemical substances, mineraloil derivatives and drying activators.The ideal natural preserver for toys,kitchen equipment, turned wooden objects, wooden furniture, wooden floors,carved items and all handicraft objects.Valuable substances out of nature under-line the beauty of a wooden surface witha silky smooth touch. The pleasantsmelling palm made of ingredientssuch as bee wax, carnauba wax, linseedoil, tung oil and orange oil not onlypreserves normal wooden surfaces.It is easily spread on cork, smoothleather and metal for protectionagainst moistureContent 300 gNo. 705350 12.52 € 14.90 €

G

The traditional wood polishing and pre-servative agent for hard-wearing surfaceswith a silky gloss. The exudate of honey-bees has been used since time immemo-rial for the care and conservation of woodsurfaces and as a filler and adhesive. Inits pure form, applied after being heatedslightly (max. 70°C), it penetrates rawwood surfaces well. Mixing with oil or alcohol can produce pasty or liquid polishes or cleaning solutions for furniture care. Granulate.Weight500 g No. 810006 10.00 € 11.90 € 1000 g No. 810007 18.07 € 21.50 €

2

B C

1 2

H

I KIRJES® NATURAL OIL WAXAccentuates the natural beauty of thewood and protects it from moisture andcontamination. The wax of the commonbearberry (Arctostaphylos uva-ursi)makes Swedish oil wax one of the top-quality organic wood preservatives.Further components include beeswaxand Swedish linseed oil. It is free fromchemicals and solvents.Content 300 gNo. 705356 17.90 € 21.30 €

I

When building up coats, please re-member the principle »soft and hard«,e.g. first a shellac priming, then atung-oil mixture, and lastly wax.

Content1000 ml No. 705288 9.66 € 11.50 €

F

D

E

Weight1000 g No. 810016 6.05 € 7.20 €

Weight100 g No. 810012 37.65 € 44.80 €

One of the mostvaluable solvents on anatural basis, ideal forthinning vegetable oils,oil paints and varnishesas well as for makingglazes and polisheswith resins, waxes orpigments. This low-viscosity oil,obtained by double-distilling the resinof the maritime pine tree, is colourlessand has a fresh, ethereal aroma.Please observe the normal safety precau-tions for the use of volatile solvents containing hydrocarbons.

F PURE BEESWAX GRANULATEProtective and fragrant:

E PROPOLIS GRANULATERefines oils and paints:


168

Tips and tricks for using, mixing pro-portions and build-up of coats can befound in our brochure »Oberflächenfibel«,which you can download free of chargefrom www.more-than-tools.de

Resins

A SHELLACThe consummate surface technique:French polishing is an incomparableway of bringing out the beauty of thewood. It creates a mechanicallywear-resistant, physiologically com-patible surface that does not becomebrittle and is of constant colour. Theresin, an exudate of a scale insect, hasbeen known since time immemorial asone of the best materials for makingclear wood finishes. Shellac is notablefor its hardness, transparency and bond-ing strength. Its excellent insulativeproperties make it the substance ofchoice for use in traditional gilding(as a primer coat and fixative). Formost applications, the shellac flakesare generally dissolved in alcohol andapplied using either a cloth rubbingpad or brush in several coats. The shellacflakes offered here are highly pure, dewaxed and can be mixed to create aspecifically desired tone or effect.

1 Astra shellacBleached, highly transparent shellac, forclear polishes.Weight250 g No. 810030 8.32 € 9.90 € 1000 g No. 810031 25.13 € 29.90 €

2 Komet shellacOrange-coloured shellac for polishes thatdisplay a slight tinge.Weight250 g No. 810034 8.32 € 9.90 € 1000 g No. 810035 25.13 € 29.90 €

3 Superior shellacReddish shellac for polishing with marked toning and for accentuating thegrain.Weight 250 g No. 810037 8.32 € 9.90 € 1000 g No. 810038 25.13 € 29.90 €

1

2

3

Note: As a natural product, shellac maydisplay variations in colour from the illus-tration.

DVD - INTRODUCTION TO FRENCH POLISHINGIn this training film,an expert shares withus the knowledge ofthe finest form of sur-face treatment asacquired by him overmany years. Peter Zehmisch explains thematerials and the individual operations(priming, basic polishing, cover polishing,polishing out scratches, and fine polis-hing). DVD, approx. 21 min. English.No. 713753 10.84 € 12.90 €

OBERFLÄCHENBEHANDLUNG VON HOLZClassic techniques andrecipes from Sam Allen.Surface treatment notonly makes wood easy to care for, it also en-hances its beauty. SamAllen provides all thecomprehensive and verypractical traditional me-thods, such as Frenchpolishing, painting, oiling and waxing,grinding, pickling and varnishing.128 pp., 165 colour illustrations, hardcover, 210 x 255 mm, in German.No. 713739 29.91 € 32.00 €

B BENZOINCaptivating aroma:Benzoin processed into paint is tradition-ally used as a glossy polished covering onshellac surfaces or high-quality oil-varnis-hed surfaces. The pure benzoin almondoffered here is obtained by cutting intothe bark of Siamese Styrax trees and re-moving the exuded and hardened resin.Benzoin is an aromatic resin of mediumhardness. Because of its agreeable, vanilla-like aroma, it is also used in themanufacture of perfumes, aromatic oils,incense and ointments.100 g granulateNo. 810023 5.80 € 6.90 €

B

Powders and pigments

C PUMICE POWDERFine polishing powder for intermediategrinding, e.g. in French polishing or asa pore filler (is transparent with shellac).Pure silicate rocks. Applied with wateror liquid paraffin.250 gNo. 810050 2.18 € 2.60 €

D DRAGON'S BLOOD, PIGMENTDragon's blood resin is soluble in spirit orwater and yields a blood-red, intensepickling that is used e.g. to colour violinpaints, oil paints, water-colour paints, orin its pure form.50 gNo. 810021 21.76 € 25.90 €

G SWEDISH RED,IRON-OXIDE PIGMENTThe classic wood preserving paint:

It determines the appearance of thelandscape of Sweden: The warm, russetcolour of the wooden facades of thebarns, houses and churches is also an ef-fective wood preservative. The pollutant-free iron-oxide pigment (unleaded) caneasily be processed in aqueous solutionor in a linseed oil emulsion to yield arich, breathing, natural paint that pro-tects the wood against UV radiation andattacks by pests. With instructions.1000 gNo. 705344 11.01 € 13.10 €

E ALKANET ROOT For tinging linseed oil:Ideal for colouring and tinging wood oilsand oil paints. The bright red to reddishviolet dyes of the alkanna root dissolvesexcellently in oil or alcohol and has ahigh power of adhesion to all organic ma-terials, such as silk, cotton, leather,wood, skin and hair.100 g granulateNo. 810024 2.86 € 3.40 €

G

NATURFARBEN HANDBUCHBy Lynn Edwards andJulia Lawless. Theauthors of this bookhave dug deeply intonature’s bag of tricksto come up with thiscollection of the bestnatural paints and gla-zes for walls and wood-work. The properties ofvarious natural pig-ments, binding agentsand solvents are described, along withnumerous recipes and finishing techniques.190 pp., numerous colour illustrations,hardcover, 190 x 290 mm, in German.No. 713253 25.13 € 29.90 €

Brushes

H FLAT OIL BRUSHHand-made in a traditional brushmaker'sshop in France for high absorption capacity, shape stability and even flow.The hand-sorted Chungking bristles withuncut, naturally split ends ensure a highcapillary effect and form a dense brushhead which allows a controlled flow.Slightly dome-shaped head for even application without overlapping. Nickel-plated ferrules, stained beech handle.Length approx. 240 mmWidth 50 mmNo. 706181 7.14 € 8.50 €

H

I SQUIRREL HAIR BRUSHFor applying shellac, fine oil varnishesand watercolours.Best quality, made from the tail hairs ofSiberian squirrels.Length 185 - 190 mmWidth13 mm No. 706109 5.71 € 6.80 € 25 mm No. 706110 7.48 € 8.90 € 38 mm No. 706111 10.50 € 12.50 € 50 mm No. 706112 16.72 € 19.90 €

F NATURAL FINISHING STARTER KIT,11-PIECE SETBasic set with great price advantage con-sisting of natural oils, waxes and resins formixing your own finishes. An attachedbrochure guides through the process.Delivered with a French flat oil brush foreasy application. Contents:Linolja, Schwedish linseed oil (705275) 1 Liter No. 705299 83.19 € 99.00 €

F

I

Lignea, Chinese tung oil (705286) 1 Liter Turpentine oil (705288) 1 Liter Pure orange oil (705277) 250 ml Sinensis, camellia oil (705280) 100 ml Flat oil brush (706181) width 50 mm Pure bee wax (810006) granulate, 500 g Carnauba wax (810009) 500 g Benzoin (810023) 100 g Alkanet root (810024) 100 g Komet shellac (810034) 250 g

A

C

D

E

Courses in French polishing can befound in our workshop programme or onthe internet at www.more-than-tools.de

Price advantage

Finishing || Glues and glue pots

169

Glues and glue pots

Titebond® gluesThe first choice when bond strength counts.For extremely solid glue joints in wood-working applications, restoration and musical instrument making. For morethan 65 years, Titebond has been themarket leader in bonding wood and wood products in the United States.

Test winner: Titebond® Ultimate IIITitebond Ultimate III emerged the ab-solute winner (best overall) from acomparison test by Fine Woodworking,the American magazine (July 2007).It achieved the highest marks for bondstrength in all woods (maple, oak, ipé)and all kinds of fit. Six wood glues werecompared: other dispersion adhesives,epoxy, liquid hide glue, hot-settingadhesive, polyurethane adhesive.

A TITEBOND® ORIGINALFor strong bonds in wood, laminates, particle board, leather, horn, bone, mother-of-pearl, cloth and porous materials forinterior use. Bond strength usually stron-ger than that of the material itself, resis-tant to most solvents, can be varnishedand is easy to sand without becomingsoft. Excess glue can be cleaned up withwater. Non-toxic and solvent-free. Assem-bly time after glue application approx. 5minutes. The dried glue joint is yellowishand transparent. Can be softened againby heating.Technical Notes: Aliphatic resin emulsionglue. Application and storage temperature10-30°C. Clamping time 30-60 minutes.Attains maximum hardness after 24 hours.Can be thinned up to 5% with water. Storage life 12 months.Weight237 g No. 450360 4.54 € 5.40 € 946 g No. 450361 11.93 € 14.20 € 3784 g No. 450369 30.42 € 36.20 €

A

C TITEBOND® PREMIUM II

Weight237 g No. 450364 5.63 € 6.70 € 946 g No. 450365 14.37 € 17.10 €

C

D

D TITEBOND® II GLUE, DARKBrown coloured glue for high strength waterproof bonds for exterior use (doors, gardenfurniture, etc). Ideal for inconspicuous gluejoints in dark woods like Teak or Iroko.Technical Notes: Cross-linking polyvinylacetate. Application temperature 10-30° C.Clamping time 30-60 minutes. Attainsmaximum strength after 24 hours. Can be thinned with 5% water. Storage life 12 months.Weight237 g No. 450372 5.46 € 6.50 €

B TITEBOND® ULTIMATE IIIExtreme water-resistance, high bondingstrength and an application time of atleast 10 minutes make it the perfect gluefor demanding applications. For both in-terior and exterior use, dries to a non-toxic, light brown glue joint.Technical Notes: Polymer glue (not for underwater use), application and storagetemperature 5-30°C. Clamping time ap-prox. 30-60 minutes, maximum hardnessafter 24 hours. Storage life 12 months.Weight 237 g No. 450362 7.06 € 8.40 € 946 g No. 450363 17.65 € 21.00 €

B

E TITEBOND® HIDE GLUELiquid hide glue for high strength, hardbonds. No creep, excellent sandability andcan be overpainted. Its sensitivity to mois-ture allows for easy disassembly of parts,making this glue particularly well suitedfor restorations and musical instrumentmaking. Long setting time, assembly timeafter glue application approx. 10 minu-tes. The dried glue joint is transparent.Technical Notes: Glutine glue with additi-ves. Not for exterior use or use on objectswhich come in contact with food. Appli-cation and storage temperature 10-30°C.Clamping time 30-60 minutes. Attainsmaximum hardness after 24 hours. Can bethinned with water. Storage life 12 months.

E

Weight 237 g No. 450368 8.32 € 9.90 €

F TITEBOND® PU-GLUEHigh-strength, water-proof, all-purposeconstructional glue. Besides wood-woodjoins, will bond almost any combinationof porous or solid materials (metals, cera-mic, plastics, stone etc). Very hard bond,dries to a yellow film, fills gaps, easy tosand, solvent-free, chemically stable,working time of 20 minutes.Technical Notes: Polyurethane glue con-tains isocyanate (avoid skin contact), andhardens by absorbing water (not for un-derwater applications), application andstorage temperature 10-30°C. Clampingtime approx. 45 minutes, maximumhardness after 4 hours. Storage life 12 months.

F

Weight 237 g No. 450366 11.09 € 13.20 €

G TITEBOND® WOODFILLERRepairs cracks, holes and other defectsin all kinds of wood. Excellent adhesion;excess can be wiped off with damp cloth.Repaired area can be sanded, cut, planed,drilled and stained easily. Not for exterioruse, non flammable. Avoid dirt and duston the working area. Apply with a spatula,rounding off on top to facilitate sanding.Let dry for two hours before sanding. Re-sists shrinking and cracking. Water-basedlatex-polymer.

G

Weight 118 g No. 450371 4.62 € 5.50 €

H BINDAN-P® WOOD GLUE (PROPELLER GLUE)High-quality, ready-to-use synthetic resinglue with outstanding power of adhesion.Even its nickname of »propeller glue« is areminder that you can trust this glue: Thefirst propellers were made by laminatinglayers of wood, and indeed with Bindan.For wood, wooden materials, cardboard,polystyrene foam, felt, fabrics and leather.Waterproof in accordance with B3, working time approx. 10 min., formaldehyde-free, solvent-free. 800 gNo. 450383 9.58 € 11.40 €

Quality verdict by German product testingfoundation Stiftung Warentest: »very good«

H

I BINDULIN DUO-MIX® EPOXY GLUEGlues almost everything:Quick-setting, transparent two-compo-nent epoxy resin adhesive. Bonds metal,wood, glass, hard plastics, bakelite, por-celain, ivory and precious stones, amongother things, in 5-10 minutes. Resistantto water and chemicals. Double injector.27 gNo. 450381 8.99 € 10.70 €

J TWO-COMPONENT GLUEBINDULIN DUO-COL®

Slow-setting epoxy resin adhesive for thechemical welding of metals, steel, plastics,hard materials, also for joining glass, porce-lain, concrete and wood. Dropping time ap-prox. 2 h, hardening time approx. 10 h atroom temperature. The hardening timemay be shortened and the tensile strengthof the bond increased by the application ofheat. Glue joint slightly tinted. Resistant towater and chemicals.2 tubes x 20 gNo. 450382 6.64 € 7.90 €

K BINDAN-CIN® BOAT GLUETwo-component, joint-filling, highly wea-ther-resistant resorcinol resin adhesive.Suitable for all wood joints (even if woodis very moist and has a high resin con-tent) as well as wood-plastic joints. The glue joints, which dry to a darkbrown, are seawater resistant (B4) andtemperature resistant up to 200°C.Resorcinol resin 250 ghardener 37.5 gNo. 450380 14.71 € 17.50 €

I

J

K

L GLUE INJECTORS, 3-PIECE SETFor the specific application of glue topoints of difficult access, e.g. in repairsof veneering or chair-leg bonds, cracksetc. Also ideal for the application of oil or for the dosage of paints and other liquids. Can be dismantled for cleaning.3-piece set.Contains 1.0 / 2.5 / 5.0 mlneedle diameter 0.5 / 0.6 / 0.7 mmNo. 716232 5.38 € 6.40 €

L

Bindan® gluesBindan® glues have been produced for morethan 70 years at Bindulin in Germany.

For high strength waterproof bonds. Suitable for exterior use (exterior doors,garden furniture etc). Otherwise thesame as Titebond® Original.Technical Notes: Polyvinyl acetate glue.Application and storage temperature 10-30°C. Clamping time 30-60 minutes. Attains maximum hardness after 24hours. Can be thinned up to 5% with water.Storage life 12 months.

Finishing || Glues and glue pots

170

Hot-setting adhesivesGlues of animal origin are simple to use,resist aging, can be softened again byheating, which makes them very usefulfor repairs. In contrast to synthetic glues,they can be overpainted and pickled.Also suitable as priming for painting andgilding. Cold water is added to the glue,which is left to soak. It is then carefullyheated in a water bath.

A BONE GLUEFor hard bonds, very easy to sand.Weight250 g No. 450141 2.02 € 2.40 € 1000 g No. 450144 5.80 € 6.90 € 10 kg No. 450156 52.02 € 61.90 €

B HIDE GLUEFor elastic bonds.Weight250 g No. 450140 2.61 € 3.10 € 1000 g No. 450143 7.14 € 8.50 €

C RABBIT SKIN GLUE, GRANULATEMore viscous than either hide or boneglue. High yield, very elastic.Weight500 g No. 450153 5.21 € 6.20 € 1000 g No. 450154 8.82 € 10.50 €

D ISINGLASS GLUEFor difficult repairs requiring highestbond strengths. The glue itself consistsof the untreated air bladders of Russiansturgeons. In recent years, the drasticallyreduced fishing quotas have made thisglue a precious commodity.

A

B

C

D

Weight 100 g No. 450142 41.93 € 49.90 €

Herdim® glue potsExclusively from DICK: Water-jacketed glue pots for the uncom-plicated heating of hot-setting adhesives,priming and waxes. A built-in thermostatensures the correct temperature within+/- 3° C. Designed for constant profes-sional use, these glue pots have provedthemselves over and over again in wood-working, restoration and instrument making. Nickel-plated brass housing withheat-resistant plastic handle and slip-proof base. Maximum temperatureapprox. 85°C.

E 0.25 LITRE GLUE POTCompact glue pot for violin making andother precision small scale work.Ø 105 mm, height 160 mm, 120 W

Ceramic container220 V No. 736001 142.02 € 169.00 €110 V No. 736002 150.42 € 179.00 €

Plastic container with lid220 V No. 736013 138.66 € 165.00 €110 V No. 736014 147.06 € 175.00 €

F 1 LITRE GLUE POTFor large-scale projects such as restora-tion, piano making, painting, stucco andgilding. Includes plastic glue containerwith lid.Ø 160 mmHeight 220 mm240 W220 VNo. 736003 202.52 € 241.00 €

E

Spirit lamp

K SPIRIT LAMP WITH DIAL REGULATOR

No. 706013 10.00 € 11.90 €Replacement wick, 15 cmNo. 706014 1.01 € 1.20 €

K

Glue brushes

L GLUE BRUSHESNatural bristles, wrapped in corrosion-freestring to prevent discolouration of the glue.Length 200-240 mm

Ø head1 14 mm No. 706105 4.62 € 5.50 € 2 16 mm No. 706106 5.46 € 6.50 € 3 18 mm No. 706107 6.30 € 7.50 € 4 21 mm No. 706108 7.98 € 9.50 €

N FRENCH GLUE BRUSHESThe split-ended, uncut bristles give thesebrushes excellent capillary power. Hand-made using natural bristles from free-rangehogs. Corrosion-free string wrapping.Length 280-300 mm

Ø head1 4 mm No. 706130 3.45 € 4.10 € 2 6 mm No. 706131 3.53 € 4.20 € 3 8 mm No. 706132 4.03 € 4.80 € 4 10 mm No. 706133 4.96 € 5.90 €

M LINDEN BAST GLUE BRUSHMade from linden bast fibres absolutelyfree of fat, ideal for the application of hot-setting adhesives, pickling and cleaningglue joints. The bast bristles are stiff, veryresistant to wear and can be shaped usinga chisel for very precise application of theglue. When the head becomes worn, newbristles can be produced by progressivelyhammering apart the linden fibres furtherdown the handle. Length 210 mm

Width1 6 mm No. 706125 3.11 € 3.70 € 2 11 mm No. 706126 4.54 € 5.40 € 3 14 mm No. 706127 6.05 € 7.20 € 4 30 mm No. 706128 12.44 € 14.80 €

N

F

4

L

31 4

31 2 4

M

G PLASTIC GLUE POTAsymmetrical, double-chambered con-tainers, 1/3 divided, for simultaneouslyheating glue and water (for thinning pur-poses). Made of polypropylene; tough,heat resistant and chemically neutral.

Content1 250 ml No. 736015 3.78 € 4.50 € 2 Lid with hole for brushNo. 736016 4.96 € 5.90 €

1000 ml No. 736007 8.32 € 9.90 € Lid with hole for brushNo. 736008 8.32 € 9.90 €

321

Glue Container

H GLASS GLUE CONTAINER, 250 ML1 No. 736005 11.68 € 13.90 €2 Lid with hole for brushNo. 736012 10.34 € 12.30 €

I CERAMIC GLUE CONTAINERContent250 ml No. 736000 8.07 € 9.60 € 1000 ml No. 736009 16.47 € 19.60 €

J STAINLESS STEEL GLUE CONTAINER 250 mlNo. 736006 8.82 € 10.50 €

Glass container with dail regulator, 120cm3 capacity, burning time approx. 2-3hours. Can be set upright or at an angledue to its polygonal shape. Round wick Ø 6 mm, with cap.

G

2

1

2

J

I

H

2

1

European wood | 173

Exotic wood | 174

Stabilised wood and laminated materials | 175

Nuts, cones, roots etc. | 176

Linen, rattan | 176

Semifinished wooden products | 176

Leather | 177

Horn | 178

Other animal materials | 179

Shoji paper | 179

Steels | 180

171

A dream come true!

Materials

172

Whether you are building a table, turning

a wooden box or forging a knife blade –

choosing the appropriate material is

essential for your success.

Beauty and function are mutually dependent

since it is only possible to create sleek

workpieces when using the appropriate mate-

rial. Therefore you will find clear instructions

with most of the natural building materials

and metals that we present in this chapter

with regards to their qualities and possible

use. The focus of our offer is on high quality

and rare natural materials for craftspeople,

turners and knife makers.

WoodThere is no material as versatile as wood.

We owe it to nature to make the best out of it.

Not less than 70,000 kinds of wood exist

worldwide. We present domestic and exotic

species that are suitable for handcrafted

purposes. Our woods are not subject to

species protection.

Solid wood has growth related anisotrope

properties, which means that it shrinks un

evenly when being dried. This has to be taken

into consideration when working the wood and

its storage. Only the proper finish will bring out

its beauty. We use natural coatings like

shellac, oil and wax that harmonise with wood.

In our range you will find blanks for turners,

handle scales for knife makers, as well as

blocks and boards for carving. Special woods

for instrument making are to be found in our

music catalogue or on our website.

HornWithin living memory, horn is one of the most

versatile and most beautiful natural materials.

It lies well in your hands, regulates humidity,

does not contain any allergenic substances

and is thus excellently suitable for products

that are in contact with human skin, e.g.

combs, jewellery, knife handles etc.

The material does not influence the taste of

any foods, therefore even sensitive food like

caviar can be purely enjoyed. Horn is harder

and denser than most kinds of wood.

Even though it has fibres it can easily be

turned or carved. Horn can become brittle

when drying, treating it with shelllac or oil

will protect it.

LeatherSkins and coats have ever been a protecting

cover to human beings. But only since people

have learned how to conserve it has it been

called leather. Leather is one of the most

versatile and most comfortable materials.

Our assortment ranges from vegetable tanned

leather, which is perfectly suitable for knife

sheaths, smooth elk leather reindeer, elk,

kangaroo and elk for bags, covers or clothing.

We also offer fish leather (ray, salmon, etc) of

beautiful structure for ornaments and book

covers.

Workshops

Basic Leather Working

Hallmarking

Knife Sheat Made from Leather

SteelNo other culture in the world has refined the

production of cutting steel more than Japan.

Japan still renders homage to the myth of the

Samurai sword. This is the reason we did

not only focus our offer on tools and knives

but also on half-finished products made out

of steel and blades. We supply not only the

material but also the know how for the proper

treatment. For more than 30 years we have

exchanged experiences with Japanese

blacksmiths and material specialists and

included this knowledge in the manual which

is sent with each half-finished product.

Forging workshops led by experts will be

helpful to beginners and advanced learners

when it comes to working these demanding

steels. For those who do not want to forge on

their own but still create beautiful knives we

also offer many blades in different kinds of

forms as well as semifinished products.

Workshops

Metalworking

Simple Forging

Pan Forging

Iron Smelting in furnace

For more information see

www.more-than-tools.de/workshops

MATERIALS DETERMINE THECHARACTER OF A WORKPIECE

Materials || European wood

173

European wood

A LINDENWOODThe linden tree is not only a tree ofmyths, fidelity and love (Freya, goddess offertility lived in one), it’s also one of thecarver’s favourite woods. Its soft woodand uniform cell structure allows it to be easily worked by hand.

1 Lindenwood blocks1st quality300 x 100 x 80 mmNo. 831288 6.30 € 7.50 €300 x 130 x 90 mmNo. 831109 7.14 € 8.50 €400 x 100 x 80 mmNo. 831289 9.16 € 10.90 €400 x 130 x 130 mmNo. 831110 16.47 € 19.60 €

2nd quality (slight fractures, discolorations)300 x 130 x 90 mmNo. R831109 3.95 € 4.70 €400 x 130 x 130 mmNo. R831110 9.16 € 10.90 €

2 Lindenwood boardFor carving and chip-carving.250 x 175 x 25 mmNo. 831103 6.47 € 7.70 €

Special sizes of lindenwood availableupon request.

C BOXWOODBoxwood is the wood turner's dreamcome true - it has a very fine grain,is rigid but easy to work, finisheswell and takes on a beautiful polish.Perfect for making bowls, figurines,handles, balls, mechanical parts -the possibilities are limited only bythe size of the blank. Large piecesof this slow-growing wood are very rare.Harvested in the French Pyrenees.

1 French boxwoodPremium-quality wood, few knots, virtual-ly no cracks. Lengths 200-600 mmApprox. 5 kgCross section50-75 mm No. 520081 58.74 € 69.90 €

Approx. 10 kg50-75 mm No. 520082 91.60 € 109.00 €76-130 mm No. 520086155.46 €185.00 €

2 Boxwood rounds, approx. 5 kgVarious diameters and lengths, air-driedfor at least 3 years.Ø from ca. 40 mmNo. 520037 25.13 € 29.90 €

D MASUR BIRCHThe contrast between the light-colouredheartwood and dramatic dark-colouredrays running through the wood have madeMasur birch wood from the polar regionshighly sought after by carvers and woodturners alike. Masur birch is both highlywear resistant and warm to the touch,making it the perfect choice for exquisiteknife and tool handles, kitchen utensils,decorative objects, intarsia and smallbowls. Air dried pieces, specially selectedfor their lively grain patterns.

1 Premium qualityHighly figured.120 x 40 x 30 mmNo. 831325 13.36 € 15.90 €120 x 50 x 30 mmNo. 831327 15.88 € 18.90 €

G OLIVE WOOD

1 Wild olive (Mutenye)Hard, dense heartwood with a lively grainfor turning and carving, for knife handlesor inlay work. The natural oil content makes it particularly resistant to waterand soiling.150 x 20 x 20 mmNo. 831263 2.44 € 2.90 €150 x 38 x 38 mmNo. 831165 3.19 € 3.80 €300 x 38 x 38 mmNo. 831166 7.14 € 8.50 €380 x 38 x 38 mmNo. 831264 10.84 € 12.90 €150 x 150 x 50 mmNo. 831167 18.40 € 21.90 €

3 Olivewood offcuts, approx. 4.5 kgA random assortment of beautifullygrained pieces of olivewood inirregular sizes, some of which haveslight defects and cracks. Suitablefor small carvings, turned pieces,jewellery, knife handles or inlay work.No. 831131 17.23 € 20.50 €

E BRUYÈRE WOODWood harvested from the root stock ofthe French wild briar tree has beensought after by pipe makers for centuriesdue to its beautifully figured grain andhigh resistance to heat. Its unique ap-pearance and excellent polishing quali-ties also make it great for making jewel-lery, intarsia and knife handles.95 x 30 x 6 mm Price per pieceNo. 831153 4.79 € 5.70 €

B WOODTURNING ASSORTMENTFrom western precious wood:Fine-quality, dry blanks for the beginningturner. Cylindrical blanks of differentthicknesses and diameters, with waxedend grains. The bags contain a randomselection of European hardwoods (cherry,maple, pear, ash, elm, acacia etc.).

Approx. 3 kgRounds Ø 80-180 mm.No. 831015 16.72 € 19.90 €

Approx. 6 kgRounds Ø 80-220 mm.No. 831016 34.37 € 40.90 € Approx. 50 mm

No. 831341 12.52 € 14.90 €

3 Boxwood assortment, approx. 4.5 kgTop-quality boxwood, air-dried for atleast 3 years, free of cracks.A typical assortment contains several19 x 19 to 38 x 38 mm squares,150-300 mm in length,and two rounds Ø 50-65 mm.No. 520038 43.61 € 51.90 €

2 1st quality120 x 40 x 30 mmNo. 831326 7.98 € 9.50 €120 x 50 x 30 mmNo. 831328 8.82 € 10.50 €200 x 50 x 50 mmNo. 831329 24.29 € 28.90 €

3 Lindenwood boards – 5 piecesClose-grained and of uniform cellstructure are these boards of muchsought-after native Lindenwood.For carving, chip-carving, printingblocks and toys.Length 350 mmWidth 130-200 mmThickness 40 mmNo. 831178 14.20 € 16.90 €

2 Sicilian olivewoodSlow growing wood of the Sicilian olivetree with attractive grain. Due to its veryhigh density and excellent polishability,it is suitable for making everyday piecesand jewellery of high aesthetic value andwear-resistance. The cuts on offer arerelatively fresh and therefore have to beprocessed under controlled drying condi-tions (instructions included).150 x 20 x 20 mmNo. 831186 5.46 € 6.50 €150 x 38 x 38 mmNo. 831187 6.89 € 8.20 €300 x 38 x 38 mm.No. 831105 12.52 € 14.90 €300 x 65 x 65 mmNo. 831106 18.40 € 21.90 €

A

1

2

3

B

1

C

2

3

1

D

2

E

F

1

G

2

3

1

2

F JUNIPER, GRAINEDThe wood obtained from the French juniper is fascinating, not just because of its wild-grown structure but also itsenduring aromatic fragrance. The water-repellant and skin-friendly wood is idealfor handle shells for knives. The oval»wood pebbles« can be used as air fresh-eners in rooms or cupboards, where theyalso keep out moths.

1 Offcuts2 pieces each, 105 x 30 x 8 mmNo. 831340 8.32 € 9.90 €

2 5 Wood pebbles

Materials || Exotic wood

174

Exotic wood

A EBONYEbony, one of the hardest, densest woodsin the world, is often used in turnery,cabinet making, restoration work and in-strument making for parts which need toeither be particularly beautiful or resist-ant to wear, e.g. keys, furniture and toolhandles, jewellery, bowls and intarsia.Ebony takes on an excellent finish due toits fine-pored structure.Due to high demand, delivery times maybe delayed. We will inform you immedi-ately, if this is the case.

2 Ebony assortment, approx. 4.5 kgHeartwood ranging in colour from jetblack to slightly striped. A typical selec-tion contains 19 x 19 to 38 x 38 mmsquares, 10-25 cm in length, plus1-2 larger pieces. Ca. 10-20 pieces total.All the pieces have waxed ends and arevirtually free of cracks.No. 831020 46.13 € 54.90 €

C ROSEWOODRosewood has always been prized as oneof the finest woods, coveted equally byturners, wood sculptors and musical in-strument makers. Its pink-to-crimson an-nual growth rings bordered by dark brownveins are visually striking. High density(850 kg/m3), load-bearing, aromatic,polishes well.

520 x 70 x 8.5 mmNo. 831029 6.64 € 7.90 €150 x 150 x 50 mmNo. 831143 18.74 € 22.30 €

B GRENADILLWith a bulk density of up to 1400 kg/m3,the dark brown to black heartwood is oneof the hardest, densest and most durablewoods that nature can offer. Grenadill iseasy to polish and is particularly suitablefor small, high-grade turned or carvedworkpieces.150 x 20 x 20 mmNo. 831265 3.28 € 3.90 €150 x 38 x 38 mmNo. 831168 5.80 € 6.90 €300 x 38 x 38 mmNo. 831169 13.19 € 15.70 €380 x 38 x 38 mmNo. 831266 14.71 € 17.50 €150 x 150 x 50 mmNo. 831170 31.85 € 37.90 €

D PINK IVORYPink Ivory (Berchemia zeyheri) is one ofthe most magnificent coloured woods,with a spectrum ranging from bright pinkto fiery red. Extremely dense (990 kg/m3)with the finest pore structure, it takes ona fine polish and is ideal for creating ex-quisite pieces of jewellery, knife handlesand turned pieces.150 x 20 x 20 mmNo. 831139 2.94 € 3.50 €150 x 38 x 38 mmNo. 831144 6.64 € 7.90 €300 x 38 x 38 mmNo. 831260 10.84 € 12.90 €380 x 38 x 38 mmNo. 831145 12.52 € 14.90 €125 x 125 x 50 mmNo. 831087 23.95 € 28.50 €150 x 150 x 50 mmNo. 831171 29.83 € 35.50 €

G WESTERNRED CEDARAlaska cedar is one ofthe finest woods for car-ving and turning, thanksto its slow growth, dura-bility, and good workabili-ty. With colour rangingfrom pink to reddishbrown, a low resin con-tent and the ability to take on a silky finishwithout additional substances, this wood iswonderful for creating highly expressiveobjects. Untreated, seasoned blocks.300 x 150 x 150 mmNo. 831014 35.97 € 42.80 €

F COCOBOLOCocobolo is one of the most magnificentprecious woods with its deep red heart-wood striped with dark brown/black veinsand a slightly wavy grain. Despite itsstrength, it is an excellent turning woodthat produces wonderful surfaces. Usedfor woodwind instruments, handles, andjewellery, for inlay work and much more.Density approx. 1100 kg/m3.150 x 25 x 25 mmNo. 831248 3.78 € 4.50 €150 x 38 x 38 mmNo. 831249 5.46 € 6.50 €300 x 38 x 38 mmNo. 831077 10.00 € 11.90 €300 x 50 x 50 mmNo. 831079 15.88 € 18.90 €150 x 150 x 50 mmNo. 831078 25.13 € 29.90 €

H SNAKEWOODSnakewood (also known as Amourette) isone of the most decorative and hardestwoods in the world.

It is called snakewood because of thewavy, almost scale-like appearance of itsgrain, which is very similar to snakeskin.Perfect for making extraordinary jewellery,knife handles and turnery. Price per piece.95 x 30 x 6 mmNo. 831150 6.89 € 8.20 €120 x 30 x 20 mmNo. 831151 19.16 € 22.80 €120 x 30 x 30 mmNo. 831152 27.56 € 32.80 €

1 Ebony blanks300 x 50 x 15 mmNo. 831021 4.37 € 5.20 €520 x 70 x 8 mmNo. 831022 9.08 € 10.80 €300 x 38 x 38 mmNo. 831140 12.35 € 14.70 €150 x 150 x 50 mmNo. 831141 37.39 € 44.50 €

I BOCOTEBocote (Mexico Rosewood) is a decorati-ve hardwood from South America of lightbrown colour with dark brown veins. Dueto the high oil content, this wood is per-fect for turning and polishes very well.Density approx. 1100 kg/m3.150 x 25 x 25 mm.No. 831267 3.28 € 3.90 €150 x 38 x 38 mmNo. 831268 4.37 € 5.20 €300 x 38 x 38 mm.No. 831075 9.16 € 10.90 €300 x 50 x 50 mm.No. 831182 14.62 € 17.40 €150 x 150 x 50 mm.No. 831076 25.13 € 29.90 €

J MOPANEBrownish red to violet hued, high densityheartwood from South Africa. The nar-row-ringed, evenly-grained wood is char-acterised by a fine dark brown veiningand light brown to green sapwood.150 x 20 x 20 mmNo. 831261 2.10 € 2.50 €150 x 38 x 38 mmNo. 831162 3.61 € 4.30 €300 x 38 x 38 mmNo. 831163 8.07 € 9.60 €380 x 38 x 38 mmNo. 831262 10.84 € 12.90 €150 x 150 x 50 mmNo. 831164 17.98 € 21.40 €

K PALMWOOD

No. 831343 10.84 € 12.90 €E ASIAN WOOD SAMPLE SETCollection of 20 different types of woodfound primarily in Asia: Champac, box-wood, cedar, rubberwood, maple, silver-wood, gamari, pine, mango, haldu, maho-gany, toonwood, badam, jackfruit, teak,coconut palm, padauk, ebony, rosewood,sisham and laurel. Polished on one side.Plate approx. 85 x 45 x 3.5 mmNo. 831010 10.84 € 12.90 €

1

A

2

B

C

D

E

F

G

H

I

J

K

Its distinctive grain structuremakes palmwood a difficultmaterial to work with. But itsdark-brown clusters of fibreset in the light heartwood gives it an extremely vibrant appearance,making it desirable for knife handles andornaments.120 x 40 x 30 mm

Materials || Exotic Wood, Stabilised wood and laminated materials

175

A AUSTRALIAN PRECIOUS WOODSIn stark contrast to many types of tropi-cal precious woods, Australian preciouswoods are harvested in a strictly con-trolled manner exclusively by federally licensed timber merchants. Burls growingon 100-year-old trees are carefully re-moved in a manner which actually revi-talizes the living tree. The extraordinarilywild grain makes these timbers wonderfulfor turning bowls and boxes, makingknife handles, and carving fine objectsand jewellery.

1 Bowl blanks assortmentA random selection of colourful Australianhardwood blanks for turning shallow bowls.Waxed end grain, virtually crack-free. Theselection can include such woods as redmallee, sheoak, goldfield, lace sheoak, figured jarrah and mulga.Approx. 5 kgFrom 120 x 120 x 50 mmNo. 831115 58.74 € 69.90 €Approx. 10 kgFrom 200 x 200 x 80 mmor 300 x 300 x 50 mmNo. 831116 117.56 € 139.90 €

2 Square timberBlanks for making high-quality knifehandles, turnery and decorative objects.Sealed end grain, virtually crack-free.300 x 40 x 40 mm

120 x 40 x 30 mmWood typeRed Mallee No. 831330 13.36 € 15.90 € Lace Sheoak No. 831331 8.32 € 9.90 € Fig. Jarrah No. 831332 8.32 € 9.90 € Goldfield No. 831333 10.84 € 12.90 € Mulga No. 831334 8.82 € 10.50 € Sheoak No. 831335 8.32 € 9.90 €

3 Grain wood offcut, approx. 5 kgA random assortment of beautifullygrained, colourful australian hardwoodpieces such as jarrah, goldfield, sheoak,mulga etc. in irregular sizes, some ofwhich have attached bark, slight defectsor cracks. Suitable for small carvings,turned pieces, jewellery, knife handlesor inlay work. Price per bagNo. 831132 22.61 € 26.90 €

4 Squared timber assortment, approx. 5 kgA random selection of precious woodsin fantastic colours and grain patterns.Sealed end grain, virtually crack-free.The selection can include such woodsas red mallee, sheoak, goldfield, lacesheoak, figured jarrah and mulga.From 19 x 19 mmLengths 150-300 mmNo. 831117 82.35 € 98.00 €

Wood typeRed Mallee No. 831120 28.49 € 33.90 € Lace Sheoak No. 831121 20.92 € 24.90 € Fig. Jarrah No. 831122 19.08 € 22.70 € Goldfield No. 831123 25.13 € 29.90 € Mulga No. 831124 19.75 € 23.50 € Sheoak No. 831134 16.72 € 19.90 €

Gold field Mulga Sheoak

Stabilised wood and laminatedmaterials

1 Stabilised spalted mapleThe spalted maplewood has anintensive pattern caused by fungalinfestation.No. 831177 30.17 € 35.90 €

2 Stabilised spalted birchSpalted birchwood with intensive patterncaused by fungal infestation.No. 831176 30.67 € 36.50 €

4 Stabilised bog oak blockBog oak wood comes from oak logs thatlay airtight under sand or mud in bogsfor thousands of years.No. 831175 29.33 € 34.90 €

5 Stabilised walnut burlFrom roots or burls.Fascinates withits extraordinary pattern.No. 831270 30.17 € 35.90 €

3 Stabilised lime tree burl

No. 831271 30.17 € 35.90 €

B STABILISED WOOD FOR KNIFEHANDLES AND TURNING PIECES:

6 Stabilised palmwood

No. 831342 29.33 € 34.90 €

C STABILISED PEN BLANKS

Colour1 red/blue No. 831272 8.07 € 9.60 € 2 green/yellow No. 831273 8.07 € 9.60 € 3 anthracite No. 831274 8.07 € 9.60 €

F PAPERSTONEIdeal for knife handles:Paperstone is a new product made from100% recycled paper which has been saturated with natural resins. The paper-resin mixture is then pressed togetherunder high pressure and heat. This re-sults in a material that is water- and UV-resistant and heat resistant up to 180° C.It can be worked with normal woodworkingtools and glued with epoxy glue. Food-safe. Two pieces.130 x 36 x 6,4 mmNo. 831244 8.32 € 9.90 €130 x 36 x 10 mmNo. 831245 10.00 € 11.90 €

Fore more wood our online shop: www.more-than-tools.de

E PAKKA WOODIdeal for outdoor and kitchen knives:Pakka wood is the collective term for impregnated veneers which are laminatedunder high pressure. If used for knifehandles, the shape of the handle bringsout the different wood layers which re-sults in an attractive look. Our blocks aremade from coloured birch veneers whichare completely saturated with syntheticresin. This procedure makes the materialwater-resistant and easy workable.Can be glued with epoxy glue.Two pieces, 120 x 35 x 8 mm

Colour1 ebony No. 719563 6.30 € 7.50 € 2 mahogany No. 719564 8.32 € 9.90 €

Red Mal lee Lace Sheoak Fi gu red Jar rah

A

1

2

3 4

B

1

2

4

5

3

6

1

E

1

2

FD WHITE PAPER MICARTA Tough and beautiful:Micarta is one of the most favouredhandle materials in knifemaking – evenfor fine collector’s knives. There are goodreasons for this: Micarta is producedusing a special high pressure procedurewhich combines absorbant material (cel-lulose material, linen etc.) with epoxy resin. The resulting material is an almostindestructible, resistant against oils andchemicals. Paper Micarta feels slip freeand very comfortable in the hand, evenunder wet or cold conditions. The materi-al can be easily refined by applyingscrimshaw, engraving and carving. 254 x 38 x 3 mmNo. 800348 10.00 € 11.90 €254 x 38 x 6 mmNo. 800349 15.04 € 17.90 €

2

3

C

D

For the first time we can of-fer you cross-sectional profi-les that are stabilised withresin, which emphasises thebeautiful structure and makesthe palmwood easy to work with.120 x 30 x 30 mm

Stabilised wood is completely saturatedwith synthetic resin via a vacuum-pres-sure process. The result is a durableand virtually odourless hybrid material.Stabilised wood absorbs practicallyno water, does not warp and can beworked with regular tools withoutproblems. It is therefore suitable forall areas where wood is subject to highwear and the material should notexpand and contract. Weight anddensity correspond to that of tropicalhard wood.120 x 40 x 30 mm

From roots or burls. With an extraordinarypattern.

These stabilised pen blanks made fromcross-cut poplar can easily be turned intosmall objects. The different colours create unique patterns.150 x 20 x 20 mm

Materials || Nuts, cones, roots etc., Linen, rattan, Semifinished wooden products

176

Semifinished wooden products

1 Shaker pegsOverall length 82 mmØ 25 mmTenon length 16 mmTenon Ø 13 mmNo. 820090 2.44 € 2.90 €

3 Small drawer pullOverall length 32 mmØ 16 mmTenon length 12 mmTenon Ø 6 mmNo. 820092 1.26 € 1.50 €

2 Large drawer pullOverall length 42 mmØ 30 mmTenon length 15 mmTenon Ø 19 mmNo. 820094 2.10 € 2.50 €

1 Violin pegsHead Ø 22 mmshank Ø 9 mmNo. 820072 1.18 € 1.40 €

2 End buttonsHead Ø 14 mmshank Ø 8 mmNo. 820075 0.50 € 0.60 €

J WOODEN DOWELSFine-grained, East Indian hardwood(haldu) for making wooden screws,dowels and turned objects. Finishesand polishes well.Length 500 mmØ 12.5 mm No. 831001 2.94 € 3.50 € 19 mm No. 831002 3.78 € 4.50 € 25 mm No. 831003 4.79 € 5.70 € 32 mm No. 831004 5.63 € 6.70 € 38 mm No. 831005 7.06 € 8.40 €

K BAMBOO BACKINGS

Width40 mm No. 708900 67.14 € 79.90 € 45 mm No. 708901 83.95 € 99.90 €

H SHAKER PEGSSimple, yet elegant, hand-turned Shaker-style knobs and coat hangers of pure design and perfect workmanship. Fine-grained boxwood, polished, with taperedtenons.

I VIOLIN PEGS AND END BUTTONSAlso serve as fine furniture knobs. They are made of exquisite ebony, haverounded edges, slightly tapered shaftsand polished surfaces.

Nuts, cones, roots etc.

A TAGUA NUTS, 1 KGThese amazing high-density nuts are pro-duced by the female species of the ivorypalm tree native to Ecuador. Their marbled,creamy white flesh can easily be carved,sanded, turned, scraped (scrimshaw) andpolished to make an endless array of ornamental objects. Tagua nuts are com-pletely free of toxins and thus suitable formaking children's toys. The surface canbe stained or coloured using textile dyes.Weight per nut approx. 30-60 gØ approx. 30-50 mmNo. 831042 9.92 € 11.80 €

B BLACK WALNUTSThe fruits of the Ameri-can black walnut tree have very hard, wrinkled inner shells with surpri-singly intricate interiors.When cut lengthwise orcrosswise (preferablywith a Japanese Dozukisaw, e.g. No. 712808),the nuts reveal theiramorphous inner structu-re. These slices can be used to make unique, eye-catching key pendants or jewellery.Ø approx. 25-40 mm Price per pieceNo. 831040 0.76 € 0.90 €

C GOLDFIELD BURLSFine-grained,impressivelycoloured Aust-ralian burls.Their naturalround shapeand high densi-ty makes them ideal for turningunique bowls.Weight per burl 1-12 kg price per kgNo. 831100 15.04 € 17.90 €

D BANKSIA CONESThe irregularly shapedcones of the banksia grandistree can be easily turned tomake unique and bizarrevases, jewellery and othersmall objects.Size 1Ca. 400-650 gNo. 831101 4.12 € 4.90 €Size 2Ca. 651-1000 gNo. 831111 6.64 € 7.90 €

E GRASSTREE ROOTSCylindrical root ofthe grass tree (Xant-horrhoea). The woodis easy to turn andoxidizes to a red-brown colour onceexposed to air.Length 150-500 mmWeight 1-10 kg Price per kgNo. 831102 10.84 € 12.90 €

Linen, rattan

G RATTAN WRAPPINGFrom time immemo-rial, thin strips pul-led from rattan canehave been used towrap all types ofhandles in Asia. This natural material,which is very comfortable to hold, lendselegance to the handles of Japanese sawsas well as those of knives and other equipment. Its curved profile produces a slightlyrounded surface structure that not onlylooks attractive, it also serves to regulatemoisture, improve grip and prevent handfatigue. Smooth surface, flexible andbreak-proof, can be affixed with wood glue.

1 FineLength 3-4 m (1-2 strips)Width 4 mmNo. 708898 3.78 € 4.50 €

2 Extra fineLength 2.5 mWidth 2 mmNo. 708899 3.28 € 3.90 €

F FABRIC BAND LINEN, GREYFor breathable seats: Fabric band serves for spanning the seatsand back rests of chairs and benches(e.g. shaker furniture).

Not only is it extremely durable, compa-red to solid seat surfaces it is also extre-mely light and breathable. Fabric band isextremely easy to process: It is fastenedto the chair frame with upholstery nailsand then plaited. Exhilarating checkedpatterns can by achieved through thecombination of differently coloured tapes.Our tip: also suitable for room partitionsand panels. 100 m x 25 mmNo. 830300 46.72 € 55.60 €

H 1

2

3

I 1

2

J

A

B

C

D

E

K

F

G

1

2

Handles for Japanese kitchen knives

Kitchen knife handles made of Japanesemagnolia wood (ho), lightweight, water-proof and warm to the touch.Tang hole is pre-drilled.

1 Small, with finger groove115 x 22 x 18 mmNo. 719565 11.34 € 13.50 €

2 Large, with finger groove125 x 27 x 22 mmNo. 719566 11.68 € 13.90 €

3 Without finger groove125 x 27 x 22 mmNo. 719567 11.68 € 13.90 €

M MAGNOLIA KNIFE HANDLES WITHBUFFALO HORN FERRULETang hole is pre-drilled.

1 Without finger groove128 x 28 x 22 mmNo. 719561 19.92 € 23.70 €

2 With finger groove135 x 24 x 18 mmNo. 719562 19.08 € 22.70 €

N CEDAR KNIFE HANDLEWith finger groove. Cedar wood, plasticferrule. Tang hole is pre-drilled.125 x 27 x 21 mmNo. 719560 6.81 € 8.10 €

Root and grained wood may have irre-gularities, inner cracks and pockets.

L1

2

M

3

1

2

N

We recommend pressing the heated tang into the knife handle withoutglue.Therefore even when the tang becomes loose, it can be re-adjusted for a tight fit.

Ideal for making bows:Japanese backings inabsolute prime quality,unblemished surface, long and regularknot distances, precisely dressed andtrimmed for easy processing.Bundle with 5 backings.Length 2 m

L MAGNOLIA WOOD KNIFE HANDLESWITH GLUE-LAMINATED BUBINGA WOODSCALES

Materials || Leather

177

Leather

A SWEDISH COWHIDEVegetable tanned:Strong, vegetable-tanned leather madefrom Swedish cowhides. Approx. 2.2 mmthick, acid-free, excellent for makingknife sheaths. Natural colour, soft (canbe hardened using soda), colourable.

Half side (= ¼ skin)Approx. 10-12 sqft. Price per sqft

Colour1 Natural No. 820128 13.28 € 15.80 € 2 Brown No. 820129 13.78 € 16.40 €

BlankApprox. 120 x 250 mm

Colour3 Natural No. 709071 6.64 € 7.90 € 4 Brown No. 709072 7.14 € 8.50 €

(sqft. = square foot = 0.093 m2, conventional measuring unit for leather)

B BARK-TANNED SWEDISH LEATHER,FOR MAKING KNIFE SHEATHSFrom the purveyor to the court:Jan Sandlund'stannery, the officialsupplier of the Swedishroyal court, makes thisfine leather using a technique that is many centuries old. The time intensiveprocess involves tanning the leather inbark extracts and then air drying it. The so-called »rough edge leather« has abeautiful natural patina that continues toimprove with age. It is easy to shapewhen wet, but is very hard and wear resistant once dried. In addition, it willnot corrode steel and is hypoallergenicand gentle on the skin. A truly uniquenatural product.Thickness approx. 2 mm20 x 30 cmNo. 820121 25.13 € 29.90 €

C RHUBARB-TANNED SHEEP LEATHERThis leather, garnered from the free-rangesheep of the Lüneburger heath, is a realrarity. By raising the sheep in a species-appropriate manner and tanning the hidewith a rhubarb-based tincture, this leath-er is as smooth as silk and exceedinglytear-resistant. The leather's beguiling aroma makes it ideal for clothing, purses, bags, shoe lining or wrapping handles.Whole hidesThickness approx. 1.2 mmSizeca. 0,5 m2 No. 831099 36.89 € 43.90 € ca. 0,7 m2 No. 831149 41.93 € 49.90 €

No. 820185 9.58 € 11.40 €

F ELK LEATHERStrong and supple:

Colour1 Medium brownNo. 820099 10.67 € 12.70 € 2 Dark brown No. 820149 10.67 € 12.70 €

E KANGAROO LEATHERIts use for making football shoes andmotorcycle clothing shows how verystrong and indestructible this leatheris. The skins of wild Australian kangaroosis vegetable tanned, barrel-dyed, andthen milled mechanically. The processingwith vegetable tanning substances makesthe leather incredibly supple and smooth,it is skin friendly and easily processed.Wildware with typical natural properties.Whole hides, approx. 0.5 m2

Thickness approx. 0.6 mmPrice per square decimeter

Colour1 Natural No. 8311881.60 € 1.90 € 2 Medium brownNo. 8311891.51 € 1.80 € 3 Black No. 8312461.51 € 1.80 €

G LEATHER STRIPFor belt loops and cords.14 x 350 mmNo. 709070 1.43 € 1.70 €

H UNDULATE RAY LEATHER, MEDIUMGRINDINGUndulate rays feature a raised structurein their middle section. When the skinsare dyed and lightly sanded, this emergesin the natural white colour in the shapeof an eye or a cross. This striking effectgives the piece a quite mythical radiance.Approx. 30 x 13 cm

Colour1 Black No. 830860 15.04 € 17.90 € 2 Claret No. 830875 15.80 € 18.80 € 3 Dark brown No. 830876 15.80 € 18.80 € 4 Grey No. 830877 16.72 € 19.90 € 5 Beige No. 830878 16.72 € 19.90 €

I BLACK UNDULATE RAY LEATHER,MEDIUM GRINDING - EXTRA LARGEApprox. 45 x 18 cmNo. 830861 31.01 € 36.90 €

J Undulate ray leather cut-offsDifferent sizes and colours.Approx. 1 kgNo. 830879 29.33 € 34.90 €

L CATFISH LEATHERThe leather of the catfish, one of the fewfish without scales, is extremely tough,durable and easily shaped. Due to its finepored structure, it is breathable and thusperfect for handle wrappings.Approx. 50 x 11 cm

Colour1 Reed No. 831220 3.03 € 3.60 € 2 Grey No. 831221 3.03 € 3.60 € 3 Black No. 831222 3.03 € 3.60 € 4 Brown No. 831223 3.03 € 3.60 €

LEDERBy Josephine Barbe.History, techniques,projects. This bookcontains important in-formation on the histo-ry of leather and intro-duces types of leatherand processing tech-niques. 25 projects, shoes, bags, cushions,jewellery and many more items are des-cribed comprehensibly and the degree ofdifficulty is indicated. 176 pages, 247colour pictures, 65 illustrations, hard-cover, 240 x 266 mm. In German.No. 713826 37.29 € 39.90 €

Tips for moulding and hardening leather By soaking leather in a soda solution(ca. 5-10 tablespoons per 3 litres ofwater, 20 minutes), it becomes moreshapeable and will harden as it dries(the word soda is derived from the Latin word solidur, meaning hard).This is particularly recommendedwhen shaping soft and semi-soft leather into knife sheaths and othershapes. The leather gets a bit darkerduring the process and takes on abeautiful patina.

A

1

2

3 4

B

C

D

E F

1 2 3 21

G

H

1

2 3 4 5

I

J

L

K

K SALMON LEATHER, BARK-TANNED

No. 831275 20.92 € 24.90 €

1

2

3

4

D REINDEER LEATHER, WHOLE HIDEVegetable tanned:Leather made from the hides of polarreindeer is particularly soft, yet highlydurable and shapeable at the same time.This makes it well suited for making shoes,gloves, hats and other articles of clothing

as well as for a variety of other leather-working projects. Whole hides, red-brown.Thickness approx. 0.8 mmApprox. 10-12 sqftOuter dimensions approx. 1.1 x 1.1 m

Price per sqft

The skin of the Scandinavian elkuniquely combines qualities likesoftness and sturdiness. Its distincttexture becomes even more beautifulby use. The leather is equally suitablefor clothing, bags, belts or linings.Gained as a by-product from hunting,the hides show two or more bullet holes.We supply whole or half hides.Thickness approx. 2.5 mmApprox. 11-22 sqft Price per sqft

The (approx. 0.4 mm thin) but hard-wearing salmon leather is soft to thetouch and easy to work with. Since thetanning is a complex process, this type ofleather is rarely found in good quality.Our hides are plant tanned using chest-nut bark in a procedure developed by theNanai (original inhabitants of Siberia)and then varnished. Half skins.Approx. 60 x 10 cm

Materials || Horn

178

Horn

Since the dawn of mankind, horn hasbeen used for a plethora of craft andartistic purposes. It can be worked rela-tively easily by sawing, sanding, turningor carving, it polishes well and can be re-shaped when it is heated. Unlike plastic,horn is non-static, regulates moisturewell and is gentle on the skin.

C WATUSSI HORN SQUARESHorn squares made from African Watussicattle, ideal for small turnery, jewellery,inlay etc.75 x 15 x 15 mm

Colour1 Dark No. 831035 6.22 € 7.40 € 2 Medium No. 831036 6.22 € 7.40 € 3 Light No. 831037 6.22 € 7.40 €

Their lively markings and translucencymake them ideal for inlay work and artand craft objects. In restoration, they canbe used as a substitute for tortoiseshell.160 x 60 x 2 mm Price per pieceNo. 831089 12.27 € 14.60 €

F HORNSTRIPS FOR BOWMAKERS

Overall length 650-750 mmNo. 831290 25.13 € 29.90 €Overall length min. 750 mmNo. 831291 37.73 € 44.90 €

K BUFFALO HORN TIPS, POLISHEDPolished water buffalo horn tips, suitablefor bow tips, jewellery, furniture handlesand other small objects.Length ca. 6-7 cmØ Approx. 20-25 mm Price per pieceNo. 831033 7.48 € 8.90 €

I RAMS HORN, PAIRSpiral-shaped horn pairs from semi-wildPyrenees sheep. Its wavy pattern makesit not only suitable for decorative objects,but also for craft applications, e.g. forhande scales or jewellery. Available inpairs only (taken from the same animal).Length ca. 300 mmNo. 831059 69.33 € 82.50 €

L YAK HORNS, PAIR

No. 831161 62.18 € 74.00 €

M RAM'S HORN SCALESought-after material for knife handle scales:

No. 831185 8.74 € 10.40 €

O STAG HORN CROWN PIECES

No. 831060 4.96 € 5.90 €

Tools for engraving horn according tothe scrimshaw technique available online: www.more-than-tools.de

H BLACK BUFFALO HORN PLATE,POLISHEDThe horn of the African water buffalo is afantastic natural material. It is easy towork by turning, carving, sanding or steam bending. When used as a knifehandle, it can be refined with white ornaments using the scrimshaw technique. Sanded and polished.Approx. 100 x 50 x 3-4 mmNo. 831224 3.28 € 3.90 €

A COLOURED COW HORNThe vividly structured horn of the Indianand African cow (Bos Indicus) is a fan-tastic natural material. It is easy to workby turning, carving, sanding or steambending to make vessels, knife handles,musical instruments, inlays or other uni-que objects.

E INDIAN WATER BUFFALO HORN,EXTRA-LONGThe extra-long horns of Indian waterbuffalo (Bubalus bubalis) are genuinerarities. They are well suited for furtherprocessing for inlay, turning and jewelrywork.Length at least 50 cmNo. 831044 15.88 € 18.90 €

G BUFFALO HORN PLATES, EXTRA LONGPlates made from the extra long, blackhorns of the Indian water buffalo (buba-lus bubalis), a domesticated and not en-dangered species. The plates are well-suited for making jewelry, inlay, mouthpieces etc.Length approx. 400-500 mmWidth approx. 40-60 mm Price per pieceThickness3-5 mm No. 831031 16.55 € 19.70 € 6-9 mm No. 831032 22.27 € 26.50 €

A1

2

B

1

2

3

C

D

E

F

G

H

I

J

K

L

M

N

1

2

O

Outside

Inside

1 Whole hornsExtra-long horns, nicely striped colour,sanded and polished.Length approx. 500 mm Price per pieceNo. 831050 28.15 € 33.50 €

2 Horn platesSanded and polished. Approx.100 x 50 x 3-4 mm Price per pieceNo. 831058 6.05 € 7.20 €

B FLAT COW HORN PLATES,TRANSPARENT

In archery language, horn is said tohave a »memory«, which means that after strain the material springs back toits original position. Therefore, this rawmaterial is preferred in the making ofbows from laminates. The raw materialand the direction of the cut are essentialfor its use in bows. These horn stripsfrom domesticated water buffalo(Bubalus bubalis) are cut from theouter curve of the horn and thus havethe correct fibre flow. In addition, ourhorn always has the maximum lengthand no fibre twists.

Due to the hard living conditions in thehighlands of Central Asia, yak horns pos-sess an especially high density and firm-ness, as well as a massive cross sectionover a large part of their length. Yakhorn* is therefore eminently suitable forhandle scales, fine turning work and many other craftwork applications. Delivered in pairs.* The horns originate from the domesti-cated yaks of Mongolia and are not sub-ject to species protection.Length approx. 400 mm

The horn of semi-wild pyrenean sheep isbeautifully structured and easy to shapeand finish. These characteristics make itespecially suited as a material for makingknife handle scales. Knifemakers who seta high value on great looks, natural mate-rials and handles which are comfortableto hold appreciate Ram's Horn greatly.Even handles for larger knives may bemade out of these generously dimensio-ned Ram's Horn Scales. Length 100-120 mmWidth 30-40 mmThickness 10-20 mm Price per piece

Stag horn crowns arerarities especiallysought after byscrimshaw artists.Their high densitymake detailed workpossible, which is inbeautiful contrast tothe pedicle shell. Alsosuitable for inlays, small turnery andornamental items. Base sandedand polished.Ø 50-60 mm Price per piece

J BUFFALO HORNS, TIPSThese especially dense horns fromAfrican Zebu buffalos are ideal foramulets, brooches, buttons, bowls,spoons, knife handles, pipe mouthpiecesand many other objects. Completely solidtip pieces.Length approx. 150-200 mmØ Approx. 30-40 mmApprox. 150-350 g Price per 100 gNo. 831293 3.95 € 4.70 €

D COW HORN PLATESPlates made from Norman cow horn withsteam heating and pressing. Due to theirlively yellow-brown pattern and transpa-rency, they look just like (protected) tor-toise shell. Suitable for intarsia, restoring(in place of tortoise shell), jewellery andlighting objects.Approx. 150-200 cm2

Thickness approx. 4-8 mm120-200 g Price per 100 gNo. 831292 4.20 € 5.00 €

N REINDEER HORNPieces and slices of reindeer horn, idealfor knife handle tips, handle scales andconnecting pieces.

1 SlicesØ approx. 20-30 mmThickness 14 mm Price per pieceNo. 709068 2.86 € 3.40 €

2 LengthsØ ca. 20-30 mmLength ca. 100-300 mmApprox. 70-250 g Price per 100 gNo. 709134 4.12 € 4.90 €

Materials || Other animal materials, Shoji paper

179

Other animal materials

A BONE PLATES

55 x 18 x 5 mmNo. 831154 3.70 € 4.40 €55 x 18 x 2 mmNo. 831155 3.70 € 4.40 €95 x 32 x 6* mmNo. 831156 6.72 € 8.00 €95 x 32 x 2 mmNo. 831157 6.72 € 8.00 €

B AFRICAN WILD BOAR TUSK

No. 831094 21.76 € 25.90 €

C MAMMOTH HANDLE SCALESTusks harvested from permafrostzones or glacial ice.

They are notable for their particularly at-tractive greenish, sometimes bluish, iri-descent colouring and are highly soughtafter by knife-makers and collectors alike.55 x 18 x 5 mm Price per pair

No. 831092 58.74 € 69.90 €

E MOCK IVORYThe high-grade mock ivory made ofpolyester comes astoundingly close toreal ivory, which is species protected.The colour and fine grain give the materi-al a natural appearance. The mock ivoryis good to work with; it can be turned,carved and polished to a high gloss fi-nish. Ideal for buttons, jewellery, knifehandles with a hidden tang or flat tangand for making musical instruments.130 x 35 x 25 mmNo. 831172 12.02 € 14.30 €

F BLACK HAIRS

No. 820085 24.54 € 29.20 €

I SQUARES5-piece sets.20 x 20 mm

Colour1 White No. 830800 5.63 € 6.70 € 2 Black No. 830802 6.64 € 7.90 € 3 Paua No. 830804 11.68 € 13.90 €

More mother-of-pearl available onlineat www.more-than-tools.de

Please note: All of the natural materi-als offered here are not subject tospecies conservation (CITES). Thesource species are not in danger of ex-tinction.

Mammoth tusksThe fascinating,10,000 year old relics are thefossilized tusks of the Siberian woolly mammoths(Mammuthusprimigenius). The pieces offered here have a lively surface pattern, polished, with a flatground back. Can be used as handlescales, for turning an ordinary knife into a unique rarity.

Horse HairHorse hair has long been used for manu-facturing brushes, woven fabrics and up-holstery. However, its toughness, elastici-ty and pleasantness to the touch make itideal for making hand-crafted objects aswell. It can be woven into fabrics, stringor ropes and lends jewelry and artisticobjects its won-derful silky glossand attractive,natural appear-ance. For exam-ple, the 'hitching'technique can beused to make beautiful armbands anddecorative objects from multi-colouredhorse hair (see: www.horsehairdesign.de).The hair we offer is 'dressed' sorted bylength and color, chemically washed anddisinfected multiple times and the defective hairs have been removed.

Mother-of-Pearl

Tip: Horse hair is also an exceptionalpolishing material for smoothing woodensurfaces, e.g. after applying oil.

L OSTRICH SINEWS, 5 PIECES

A

B

C

E

F

I

1 2 3

L

Shoji paper (Shoji Gami)

Japanese sliding doors, known as Shoji,serve to create a subtle barrier betweenlight and space, interior and exterior,thereby giving rooms a uniquely enchant-ing atmosphere. They are traditionallycovered with translucent paper, which isapplied to the wooden lattice using riceglue. Shoji paper is also suitable forJapanese lamps, lanterns, prints andink paintings. Rice glue included.

M SHOJI PAPER, PLAIN1 roll28 cm x 18.8 mNo. 716100 8.32 € 9.90 €1 roll94 cm x 7.2 mNo. 716103 11.68 € 13.90 €

N SHOJI PAPER,BAMBOO PRINTDelicate, water-mark-likedesign.1 roll94 cm x 7.2 mNo. 716107 11.68 € 13.90 €

O SHOJI PAPER,FIBREPATTERNFine, light fibreinclusions.1 roll94 cm x 7.2 mNo. 715997 11.68 € 13.90 €

M

N

O

D CAMEL-BONE HANDLE SCALES

No. 719575 8.32 € 9.90 €

2 BrownNo. 831090 36.97 € 44.00 €

Natural colour, very strong, silky gloss.Length approx. 700 mm

G WHITE HAIRNatural color (unbleached), thin and flexible, colorable, silky gloss.Length approx. 600 mmNo. 820087 28.49 € 33.90 €1 Greenish

1

2

D

G

H IRREGULAR PLATESRandom assortments of sizes.50 grams per pack (5-10 plates).From 20 x 30 mm to 40 x 60 mm

Colour1 White No. 830845 27.23 € 32.40 € 2 Black No. 830846 41.93 € 49.90 € 3 Gold No. 830847 33.53 € 39.90 €

J EYES, Ø 5 MMCircular pieces.20 pieces per pack.

Colour1 White No. 830816 2.69 € 3.20 € 2 Pink No. 830822 2.94 € 3.50 € 3 Gold No. 830834 2.94 € 3.50 € 4 Paua No. 830840 2.94 € 3.50 €

K EYES, Ø 10 MMCircular pieces.20 pieces per pack.

Colour1 White No. 830818 4.96 € 5.90 € 2 Pink No. 830824 5.46 € 6.50 € 3 Gold No. 830836 5.46 € 6.50 € 4 Paua No. 830842 5.46 € 6.50 €

4321

J

K

4321

H

321

For making knife handle scales, inlays,jewellery and as a replacement forelephant ivory. Very hard and resistantto wear, easy to sand and finish.Made from thick-walled, sterilizedwater buffalo bones. Price per piece

Smooth white half-round camel-bonepanels for use as knife handle scales,ornaments or inlays.115 x 33 x 6 mm Price per pair

The powerful tusks of the African wildboar (Phacochoerus africanus) can beused for making pistol-shaped knifehandles as well as other decorative objects or as material for inlays and turning.Length approx. 170-180 mmApprox. 2/3 hollow Price per piece

The shimmering multi-layered depositsfound on the inside surface of sea shellsyield one of the most fascinating naturalmaterials known to humankind. Mother-of-pearl's magical glossiness and intrigu-ing array of colors make it perfect for enhancing the appearance of turnery, furniture, ornamental objects, toys andmusic instruments. It is easy to work and

polish and therefore ideal for intarsia,marquetry and jewelry applications.The white, pink, black and gold mother-of-pearl is harvested from the saltwaterpearl (pinctada maxima). The paua moth-er-of-pearl is harvested from a musslespecies (haliotis iris) from the SouthSeas that has a highly figured and colorful grain (blue/turquoise/green). Thickness approx. 1.3 mm

Ideal for laminated backings on woodenor composite bows. The laminationincreases draw strength and preventsbreakage of the bow. Almost unlimiteddurability when stored under dry conditi-ons. These sinews are dried gently at ourcompany and so keep their elasticityafter drying. 7-9 sinews are adequatefor one composite bow.Approx. 10-30 gMinimum length 300 mmNo. 831247 15.04 € 17.90 €

* Due to their larger size, these piecesmay have some natural curvature and beslightly more porous.

From the workshop series by Ernst G. Siebeneicher and Jürgen Rosinski. Thispractical manual givesa straightforward andgood value introductionto the fascinatinghobby of blade-smithing. With countless step-by-stepphotos, it shows you how to construct asimple smith's hearth, how to make thenecessary tools yourself, how to forge astick tang blade out of spring steel and tomake it into a finished knife. 128 pages, numerous colour photographs,softcover, 170 x 230 mm. In German.

Materials || Steels

180

Steels

Multi-layer steel

B SUMINAGASHI FLAT STEEL,EXTRA THINStainless, for cooking and folding knives:33 layers of the best knife steel are re-vealed in this Suminagashi steel througha flat bevel and appropriate etching.Extremely edge-retaining medial layerfrom VG10 gold steel*. The outer layersof stainless steel give the blade thetypical Suminagashi grain. The forgingsurface is not ground-finished, temperinginstructions included.*(1% C, 15% Cr, 1% Mo, 0,2% V, 1,5% Co)2-2.2 x 55 x 250 mmNo. 719614 36.47 € 43.40 €

1 White Paper Steel coreFinest grain, sharpest grade.(C 1,2%, S<0.004%, P<0.025%)5.5 x 35 x 380 mmNo. 719617 27.31 € 32.50 €

2 Blue Paper Steel coreSomewhat tougher and more wear-resistant(carbide formation) than White PaperSteel, with a slightly coarser grain.(C 1.2%, Cr 0.4%, W 1.8%)5.5 x 35 x 380 mmNo. 719618 31.01 € 36.90 €

D MULTI-LAYER STEEL (SUMINAGASHI)The finest22-layerSuminagashisteel with amedial layer of White PaperSteel. The multi-layersteel can beground or forged and thenhardened toproduce blades of both incredible sharpness and resilience. Flat steel, not stainless. Supplied unhardened with heat treatment instructions.5.5 x 33 mm x 1 mNo. 719610 53.19 € 63.30 €

Triple-layer steels

1 Medial layer White Paper SteelUnalloyed, extremely fine crystallinestructure, similar to sword steel. Side layersfrom low-carbon-steel, not hardening.3.5 x 33 x 350 mmNo. 719615 11.85 € 14.10 €

2 Medial layer Blue Paper SteelLightly alloyed, due to carbide formationsomewhat tougher and more wear-resis-tant. Steel with low carbon content, nothardening. 3.5 x 33 x 350 mmNo. 719616 14.71 € 17.50 €

Mono steel

G BLUE PAPER STEELTough and edge retaining:Alloyed Japanese carbon-steel, martensitic,due to carbide formation somewhat tougher and more wear-resistant than White Paper Steel, coarser grain. With heat treatment instructions.(C 1,1-1,2%, Si 0,1-0,2%,Mn 0,2-0,3%, Cr 0,2-0,5%,W 1,0-1,5%, P <0,025%, S <0,004%)4.5 x 30 x 500 mmNo. 719621 31.01 € 36.90 €

H WHITE PAPER STEELThe finest grain: Non-alloy Japanese carbon-steel, finestmartensitic structure. Extremely sharp,close to sword steel. With heat treatmentinstructions.(C 1,1-1,2%, Si 0,1-0,2%,P <0,025%, S <0,004%)4.5 x 30 x 500 mmNo. 719620 24.87 € 29.60 €

»This is what knife makers have beenwaiting for.«Magazine »Katana«, 2007

I SWEDISH STEELSheets made of cold-rolled Uddeholmcarbon-steel for forging tool and knifeblades. Also suitable for forge welding.Comes with heat treatment instructions.Steel No. 1770(C 0.7%, Si 0.4%, Mn 0.7%,P <0.035%, S <0.05%)annealed, oil hardened, final hardnessApprox. 56-59 HRC.2.5 x 120 x 500 mmNo. 709099 14.62 € 17.40 €2.5 x 120 x 1000 mmNo. 709098 24.79 € 29.50 €

J JAPANESE SWORD STEEL -TAMAHAGANEThe dream of every sword smith:Japanese masters made the queen ofblades from amorphous material. OriginalTamahagane is made in the days-longTatara process using the purest ore sand(masa) and pine charcoal. We have asmall quota of this precious material,which formed the basis of over 1000years of high culture of forging swords.The material can be made into bladesby experienced blacksmiths, and is alsoan asset to every collection as an object,due to its mystically shimmering frag-ments, which are streaked by colouredmetal oxides.750-1000 g Price per gNo. 719608 0.25 € 0.30 €

For workshops on forging see online www.more-than-tools.de/workshops

K STEEL MOKUME, IN PLATE FORMMokume Gane is synonymous with vividpatterns and a play of colours in the ma-terial, produced through time-consumingwork. The semifinished product is suitable for making handcrafted objects,from jewellery to knife handle scales. Itcan be worked by filing, sawing, grinding,polishing, soldering or cold-forming. Theplate has 24 layers and is made by hotisostatic pressing of numerous layers ofsteel, copper and brass. Approx. 100 x 50 x 4 mmNo. 719612 44.79 € 53.30 €

MESSER SCHMIEDEN FÜR ANFÄNGER

No. 713796 27.85 € 29.80 €

A PM SUMINAGASHI FLAT STEELFor ultimate requirements:This novel Japanese blade steel leaves no-thing to be desired: A core of the hardestpowder metallurgical steel SG-2* makesthe blade wear-resistant and tough, thedouble-sided suminagashi plating, madeof nickel and rustproof stainless steel, gives it a spectacular appearance. Whetherused as a kitchen knife orfor outdoor use, this steelimpresses with its outstan-ding durability, sharpnessretention and resistance tocorrosion. Flat stock, untempered, furtherprocessing by forging, heat treatment in-structions included.* (C 1,3%, Cr 15%, Mo 3%, V 2%)7 x 30 x 490 mmNo. 719613 172.18 € 204.90 €3 x 40 x 250 mmNo. 719627 54.54 € 64.90 €

C JAPANESE MULTI-LAYER STEEL»KATANA«Close to the sword: Steel with thiscomposition wasfrequently usedin Japaneseswords (Katana).The high carboncore layer doesonly extend tothe middle of the blade's profile. Multiple layers of softer steel folded on either side make this metal virtually unbreakable with excellent cutting properties. This type of construction also minimizes the risk of cracking during hardening. Usually the steel is forged further, but a blade can also be ground from the steel directly. The material is supplied unhardened; instructions for heat treatment included (final hardness 62 Rockwell). Not rust-proof.

F JAPANESE TRIPLE-LAYER STEELJapanese triple-layer steel isrenowned forits extraordinarysharpness, longedge life andexcellent sharp-enability (mini-mal burr). Theycan either beground (usingwet grinders) or forged into the desiredform. Also suitable for making Damascussteel (folding techniques). Semifinishedproduct, not stainless. Supplied unhard-ened with instructions for hardening andtempering.3.5 x 33 x 350 mm

white paper steel1,5 mm

11 layers 11 layers5.5 mm

8 layers 8 layers1.5 mm

Pap

erst

eel

Iron

Paper steel1.0 mm

3.5 mm

A

B

C

1

2

D

F

1

2

G

H

I

J

K

Semifinished metal materials

L MOSAIC PINSDecorations instead of rivets:Give your knife handle scales a touchof class with these fetching mosaicpins made in Japan.The rosette-shaped pattern is composedof fine brass and copper wires cased in ahigh-strength stainless steel tube. Alsosuitable for embedding in jewellery anddecorative art.Length 120 mm

Ø mm1 5 mm No. 708390 20.92 € 24.90 € 2 6 mm No. 708391 20.92 € 24.90 € 3 7 mm No. 708392 20.92 € 24.90 € 4 8 mm No. 708393 20.92 € 24.90 €

M HANDLEHEAD PLATESBrass.20 x 30 x 3 mmFor blade thickness2.5 mm No. 709069 1.68 € 2.00 € 3.2 mm No. 709101 1.68 € 2.00 €

L

4321

M

E DAMASCUS FLAT STEELHigh-performance Damascus:This beautifully structured Damascus Flat Steel with 192 layers is made in theIndus Valley. It is forged from low alloy1095 carbon-steel (1.274) and Nickelsteel 15N20, which is often used for bandsaws. A powerful combination! The silveryNickel steel contrasts strongly with thedarker 1095 carbon steel, which producesthis nice pattern. Comes with detailedheat treating instructions.230 x 38 x 4 mm280 g1 Random damascusNo. 719402 48.66 € 57.90 €2 Rose damascus steelNo. 719404 67.14 € 79.90 €3 Firestorm damascusNo. 719406 67.14 € 79.90 €

E

1 2 3

181181

Traditional hocho | 185

Western design hocho | 191

Knives for special applications | 198

Kitchen utensils | 199

Knife blocks | 199

Cutting boards | 200

Peeler, rasps and accessories | 201

Tea bowls and teapots | 203

Cast-iron cookware | 204

Hunting and outdoor knives | 205

Blades and blade blanks | 215

Knife kits | 217

Obsidian | 218

Brief glossary of steel terms | 218

»The hocho is the soul of the cook«.Japanese proverb

Knives

182

Tools reflect the state of our culture.

The tools we use to cut food, for example,

don't just say something about our cooking

culture - but the quality of their blades, their

refined shape and the effort that was put into

their manufacture reflect our respect for what

nature provides.

JAPANESE KNIVES Japan has cultivated the aesthetics of food

preparation like no other country, with the

Hocho - the handforged knife - being the

most important tool. With it, the cook

celebrates the art of cutting, which makes

the preparation of fine fish and delicate

vegetables a feast for the eyes. The razor-

sharp cut doesn't crush the cells, the juice

is retained, and the natural flavour of the

foods comes into its own.

The blades are forged traditionally in

multiple layers, with hard carbon steel forge-

welded with tough iron. Only this elaborate

procedure ensures an optimum synthesis of

breaking strength and ultimate sharpness.

In this respect, Hocho clearly show their

relation to the Samurai sword.

The shape of these knives has developed

solely from their intended purpose, which

gives them an aesthetic quality not remotely

influenced by fashion trends. The light

wooden handles, the well-balanced design

and the extraordinary sharpness make using

Hocho a remarkable experience.

More than 25 years' import experience, the

best contacts to leading Japanese forges and,

last but not least, a 3-year warranty are your

guarantee of quality for the blades.

KITCHEN QUALITY STARTSWITH CUTTING

Usuba

Vegetable knife with straight blade for clean

cutting on the chopping board; paper-thin

slices are no problem, even with ripe

tomatoes. Wide blade for good guidance

along the finger knuckles.

Ajikiri

For small fish and for cleaning vegetables

and salads, as well as chopping herbs.

Sashimi

For cutting and filleting fish or ham with

a pull stroke. Slim blade in the shape of a

willow leaf or Katana (sword).

Deba

For cutting fish and light mincing.

Thick, wide blade. The back of the

blade can be used to chop thin bones.

Petty

Small all-purpose knife for fruit,

peeling and cutting small objects.

STANDARD EQUIPMENT

As a start, we recommend a Santoku

(all-purpose knife) and a Petty

(fruit and peeling knife).

BENEFITS OF USING JAPANESE KNIVES

* Ultra-sharp cutting for exquisite taste

The superb taste is achieved by a sharp,

clean cut that severs the cells rather than

squashing or crushing them, as a duller

blade might. This also means that the food

retains all its flavours. When cutting onions,

a sharp blade has the added benefit that only

a little juice leaks from the cuts - and it's

mainly the essential oils contained in the

juice that bring tears to the eyes.

* Minimal cutting effort

* They stay sharp longer and are

very easy to sharpen

* The blade shapes are wide,

the rear cutting edge stays sharp.

You can use the full length of the cutting

edge, which is an advantage both for

chopping and filleting.

KNIFE TYPES

Santoku

All-round knife for meat, fish and vegetables

(Santoku = the three virtues). Wide blade for

good guidance along the finger knuckles.

Gyuto

Versatile cooking knife for cutting up,

filleting and preparing meat and fish. Slim

blades for intricate tasks, pull or push cuts.

Iron (soft, resilient) Carbon steel (hard)

HOCHO TERMS

Handle end (ejiri)Ferrule (kuchigane)Neck (emoto)Blade (hira) Back (mune)

Bevel line(shinogisuji)

Tip (kisaki)

Temper line (hamon) Cutting edge (ha)

Heel (ago)

Bevel(kiriha)

Tang(nakago)

Handle (e)

Blade length (hawatari)

Knives

183

STEEL QUALITIES

* Highest quality: not rustproof

The Japanese company Hitachi Metals

makes special cutting steels which represent

the highest global standard and are used for

almost all the Hocho we offer. These Yasuki

Special Steels (YSS), named after their place

of origin, are produced from iron sand, the

same material that was used to make the

legendary Samurai swords. They have a highly

pure structure and thus offer the best achiev-

able sharpness for cutting. Different variants

of this steel are used for different purposes:

* White Paper Steel (Unalloyed carbon steel)

is particularly hard and has an especially fine

martensitic structure. This means you can

grind it to exceptional sharpness, which it

retains for a long time. These blades are

particularly suitable for the gentle preparation

of foods - but they are prone to oxidation,

which means rust.

* Blue Paper Steel

A compromise is the slightly alloyed,

corrosion-resistant Blue Paper Steel. Original

Japanese knives made from these materials

are treated with non-corrosive, food-safe

oils (e.g. camellia oil) to prevent oxidation.

* PM steels

Nowadays, Western-style knives are also

made from powder-metallurgy steels (so-

called PM steels), which are even harder

than low-alloy steel types and are even

rustproof. However, they cannot be ground to

such a fine cutting edge as unalloyed carbon

steel (White Paper Steel).

For more information on cutting steels,

see »Expert Knowledge« on our website


* Forged or stamped?

Forging by hand carefully forms the work-

piece, always keeping it within the optimum

temperature range. The striking force and

frequency are applied as required. This re-

sults in a forming process that also benefits

the crystalline structure of the metal, making

it finer, which improves the mechanical

and chemical properties of the steel. Forged

blades can be distinguished in particular by

the increasing thickness of the back of the

blade towards the tang, which makes the

blade stronger and improves the balance.

The backs of stamped blades, on the other

hand, are evenly thick. In machine forging,

only a few shaping steps are normally carried

out, which calls for much higher temperatures

than hand forging - and high heat

has a negative effect on the structure.

CHOOSING THE RIGHT KNIFE

Choosing the right knife depends primarily on

the intended purpose (vegetables, fish, meat,

all-purpose, etc.), but you should also

consider how much time you are prepared

to spend on looking after it. How »easy-care«

a knife is depends mainly on the blade steel

and the design of the handles:

Blade steel

a) Classic carbon steel (one or more layers):

not rustproof. The blade must therefore be

dried after use and regularly oiled. However,

it achieves ultimate sharpness and is easy to

sharpen.

b) Carbon steel for the cutting edge, embed-

ded in stainless steel (three or more layers).

The blade is largely rustproof, only the

exposed cutting edge can oxidise. A good

compromise between maintenance require-

ments and ease of sharpening. As sharp as a).

c) Stainless steel (one or more layers).

The blade is rustproof and does not need to

be oiled. However, due to the high chromium

content, it is not as easy to sharpen (chromium

affects the sharpening stone and causes a

larger burr). These knives are also unfit for

the dishwasher.

Handle construction:

a) Classic design with attached wooden

handles: These can expand when wet and

may become loose (light tapping will tighten

them again). These knives must be kept dry.

b) Design with full-length tang and handle

shells (integral or semi-integral design):

Depending on the material, these knives are

normally hard-wearing. However, their centre

of gravity is slightly further back and they are

usually more heavy than a).

BEWARE OF FAKES

Widely used Japanese-looking knives from

Asian low-wage countries are often only

similar in shape to the original Hocho.

All Hocho offered by DICK come from

Japan and are of the best quality.

You can distinguish mass-produced knives

by the low quality of their materials and

workmanship.

How do I recognise a Japanese knife?

The visible quality features of original

Japanese knives include:

- The traditional form.

- They often have a Japanese signature,

not a Chinese one, which is usually engraved

in the metal individually by the smith.

- As Japanese blades are always made of

at least two and usually even three layers

of metal, a wavy border line must be visible

at the cutting edge.

- The so-called Suminagashi pattern -

the damask-like structure of the multi-layer

steel - is often imitated in cheap knives by

etching, which becomes apparent at the

latest during sharpening. When buying a

knife, compare two knives of the same type.

The etched pattern is always the same, while

the structure lines of multilayer steel are

slightly different in each knife.

- Original Japanese knives are all products of

high-quality workmanship: The blade must

be absolutely straight and must sit equally

straight in the handle. No traces of machine

grinding must be visible on the cutting edge,

and the tip is also finely ground.

Knives

184

HANDLING

For precise cuts, e.g.

for thin slices, guide the

blade along the finger

knuckles of the free

hand.

For peeling cuts, e.g.

when cutting up a radish

or cucumber, hold and

turn the piece of food

close to the cutting edge.

For decorative cuts,

hold the blade close

to the tip.

Use the back cutting

edge for removing

blemishes from fruit

and vegetables, turning

the piece of food.

For filleting and sashimi,

guide the knife with

pulling strokes. The

bevelled section points

downwards.

CORRECT CARE

Cutting pad

The correct cutting pad - and this applies

to all knives, not just original Japanese ones -

is made of wood or plastic. Working on porce-

lain, marble or glass quickly dulls the blade.

Unlike in European practice, Japanese chefs

prefer soft woods such as gingko or cypress.

Sharpening

Contrary to some advertising claims, even

the best knife will not stay sharp forever.

Sharpening once in a while is therefore

essential if you want to enjoy using your

Hocho permanently. Japanese kitchen knives

are exclusively sharpened on fine-grained

waterstones. Therefore you require at least

a combination sharpening stone. Dry grinding

tools, such as sharpening steels, mechanical

grinding tools or sharpening machines,

should not be used.

Depending on how sharp you want your blade

and how often you use the knife, you should

sharpen it 1-12 times a year (the sushi

chef whets it every day, similar to a razor).

We provide instructions with each knife.

Sharpening courses

The perfect introduction to the art of

sharpening knives given by experts who

were trained in Japan.

Training video

Demonstrates the sharpening of Japanese

knives.

Sharpening primer

Our sharpening primer can be downloaded

free of charge at our webshop.

NEW: DICK-SHARPENING PASS

- All knives come with a sharpening pass

for two free sharpenings. Send us your knives

and we will return them razor-sharp within a

few days. All you pay is the postage.

HIGH CLASS SHARPENING SERVICE- High classed knives include the unlimited

sharpening service.

Just send us your knife whenever you feel

it's not sharp enough. You will get it back

sharpened free of charge within a few days.

All you pay is the postage.

GENERAL SHARPENING SERVICE- We also sharpen knives from other

manufacturers. See our webshop or page 2

for prices.

Storage

Store your knives in a wooden knife block,

knife rest or casket. Japanese cooks wrap

their knives in individual cloths.

We advise against using magnetic holders

because they magnetise the blade and

make it harder to sharpen.

Cleaning

Clean the knife by hand, rinsing it under

luke-warm water and, if required, adding a

little washing-up liquid. Do not use scouring

powder and never put the knife in the

dishwasher, even if it is rustproof. Stained

or slightly rusty blades can be cleaned with

a rust eraser.

Knives || Traditional hocho

185

Outstanding knives with traditional bladeshapes have been made in the traditionalmanner in small Japanese foundries forcenturies. Often with a high level of man-ual work or even completely handmade.Knives of this classical form are knownas »Wabocho« in Japan. They are valuedby experts because of the best steels,carefully selected materials for the han-dles and ferrules, a high level of work-manship, original design – and last butnot least, extreme sharpness and sharpness retention.

The blades usually have a hard carbonsteel core forge welded to one or twoouter layers of iron – similar to multi-layer Samurai swords. Traditional materials and forms are also used for the handles. In a demanding acceptanceprocess, DICK selects the best manufac-turers on site and carefully checks thequality of all products.

From master´s handThe master blacksmith performs all the important work only for very specialworks of art. This makes every pieceunique, special and valuable. The black-smith guarantees this with his name.

A KOBAYASHI HOCHO DELUXESpectacular blades from master craftsman:

1 2 3

Traditional hocho

A

1 Usuba (vegetable knife)Blade length 180 mmOverall length 320 mmBlade thickness 4 mm220 gNo. 719046 381.51 € 454.00 €

2 Sashimi (fish knife)Blade in the form of a willow leaf.Blade length 300 mmOverall length 460 mmBlade thickness 4 mm260 gNo. 719407 564.71 € 672.00 €

The forging of knives has always had astrongly mystical cultural history. This isthe only explanation for the fact that theproducts are often enhanced way beyondtheir actual utility. The passionate searchfor perfection characterised by the Samu-rai sword blacksmiths can still be foundin certain blacksmiths today. The impe-rial supplier Kobayashi Sensei is a mem-ber of this species. His Hochos areperfectly formed compositions of thefinest materials. He joins multiply folded(Suminagashi), high-purity carbon-steelto a cutting edge of Blue Paper Steel tomake exceptional blades with a hardnessof 61 HRC: a classical wave pattern onthe wide sides of the blade and a breath-takingly sharp cutting edge. Handlemade of makassar ebony, a very dense,non-fading and ageing-resistant exoticwood. With buffalo horn ferrule. 14 lay-ers, right-bevelled, not rustproof.

3 DebaThick-walled blade for cutting and lightchopping.Blade length 180 mmOverall length 335 mmBlade thickness 9 mm430 gNo. 719045 604.20 € 719.00 €

Inclusive sharpening service for free.Please note the information on page 2.

Free lifetime sharpening for Premium products



186

A SHIGEFUSA HOCHO

B SHIGEKI HOCHO »CLASSIC«

C SHIGEKI HOCHO »URUSHI HANDLE«

1

2

3

1

2

3

1

2

A

C

B

3

Original and pure:Master Shigefusa uses original materialsto create knives in classical shapes fol-lowing the strict code of traditionalJapanese aesthetics. With meditative de-votion, he creates the finest blades in hisworkshop using traditional swordsmithingmethods. This includes forge welding ofthe individual layers in a charcoal fur-nace, forming of the blades with ascraper blade and then grinding and pol-ishing by hand on a veritable arsenal ofwater stones. Magnolia wood handleswith buffalo horn ferrules. Cutting edgeof high-carbon steel, hardness approx.64 HRC, not rustproof.

Hard Blue Paper Steel is used for thecore cutting layer and low alloyed steelsfor the outer Suminagashi layers. Everypiece is hand signed and packed in abeautiful case made of kiriwood. Magno-lia wood handle with a buffalo horn ferrule. Hardness approx. 62 HRC, notrustproof.

1 Santoku (all-purpose knife)31 layers, double-bevelled.Blade length 165 mmOverall length 310 mmBlade thickness 2.8 mm130 gNo. 719290 100.00 € 119.00 €

2 Sashimi (fish knife)16 layers, single right-hand bevel.Blade length 230 mmOverall length 375 mmBlade thickness 4 mm160 gNo. 719183 142.02 € 169.00 €

3 Deba16 layers, single right-hand bevel.Blade length 170 mmOverall length 310 mmBlade thickness 6.5 mm280 gNo. 719184 142.02 € 169.00 €

2 Sashimi (fish knife)16 layers, single right-hand bevel.Blade length 230 mmOverall length 375 mmBlade thickness 4 mm165 gNo. 719331 247.90 € 295.00 €

3 Deba16 layers, single right-hand bevel.Blade length 170 mmOverall length 310 mmBlade thickness 6.5 mm285 gNo. 719330 247.90 € 295.00 €

1 Santoku (all-purpose knife)31 layers, double-bevelled.Blade length 165 mmOverall length 310 mmBlade thickness 2.8 mm130 gNo. 719332 149.58 € 178.00 €

Combining an ancient tradition of Japan-ese lacquerware with a fine blade to cre-ate a unique masterpiece. In Japan, theart of lacquerware has been developed toultimate perfection. Japanese artisanshave redesigned the magnolia wood han-dles of our new urushi* series followingthis technique. They are coated withdeep black urushivarnish and showhighly attractivefine gold decora-tions on the left side of the handle. Everypiece is hand signed and packed in abeautiful case made of kiriwood. Pol-ished buffalo horn ferrule. Cutting edgeof Blue Paper Steel. Hardness approx.62 HRC, not rustproof. *Urushi is extracted from the sap of theJapanese varnish tree and has been usedfor varnishing furniture, bowls, jars andhandles for more than 6000 years.Urushi is resistant to water, heat, alco-hol, acids, alkaline solutions and solventsand it is non-aging and food-safe. Urushivarnishing is considered the supreme dis-cipline of Japanese art of lacquering.

1 Santoku (all-purpose knife)61 layers, double-bevelled.Blade length 165 mmOverall length 310 mmBlade thickness 3 mm150 gNo. 719137 268.07 € 319.00 €

2 Gyuto (fish and meat knife)Triple-layered blade, double-bevelled.Blade length 210 mmOverall length 370 mmBlade thickness 3 mm180 gNo. 719211 293.28 € 349.00 €

3 Usuba (vegetable knife)Triple-layered blade, double-bevelled.Surface has a forged structure, gunmetalfinish.Blade length 165 mmOverall length 310 mmBlade thickness 3.5 mm180 gNo. 719206 133.61 € 159.00 €

Shigeki HochoEvery piece is unique:Master Shigeki practices steel folding and forge welding with great virtuosity to create blades with anenchanting aesthetic - each one unique in its structure.

No. 719009 99.66 € 118.60 €

No. 719005 60.08 € 71.50 €


187

Creations from master craftsmen

A HAYASHI HOCHO

Santoku (all-purpose knife)Blade length 165 mmOverall length 300 mmBlade thickness 2.5 mm140 g

Sheath1 With No. 719112 78.07 € 92.90 € 2 Without No. 719207 67.14 € 79.90 €

Gyuto (fish and meat knife)Blade length 145 mmOverall length 285 mmBlade thickness 2.5 mm80 g


Usuba (vegetable knife)Blade length 165 mmOverall length 305 mmBlade thickness 2.5 mm140 g


3-piece setSheathWith No. 719432 211.76 € 252.00 € Without No. 719433 184.03 € 219.00 €

B KOBAYASHI HOCHO

1 Usuba (vegetable knife)Blade length 165 mmOverall length 340 mmBlade thickness 3.5 mm185 g

Blade length 150 mmOverall length 280 mmBlade thickness 3.5 mm90 gNo. 719001 55.29 € 65.80 €

3 Blade length 210 mmOverall length 345 mmBlade thickness 3.5 mm125 gNo. 719002 62.86 € 74.80 €


5 Deba

Knives in the Kobayashi series forleft-handers, and other left-handedknives can be found in our web shop atwww.more-than-tools.de

C EXQUISITE SELECTION FROM TWOMASTER BLACKSMITHS3-piece set

No. 719027 180.59 € 214.90 €

Price advantage

A

2

4

B

1

2

3

4

5No. 713806 4.96 € 5.90 €

DVD – DAS SCHÄRFEN JAPANISCHER MESSERA Japanese master blacksmith with a legendary reputation in Japan shows youhow to professionally sharpen kitchenknives on water stones. He introducesdifferent types of whetstone, shows thecorrect sharpening motions for sharp-ening single and double-bevelled knivesand provides information on caring forknives. Knives sharpened in this way notonly make your work easier but are also a pleasure to use and allow you to treatyour food with respect.DVD 15 min, in German.

C

1

6

3

5

Light and elegant:Aesthetically pleasing knife with atwelve-layer blade from Damascus steel.The blade is grounded very thin and al-lows you to cut very fine. The handles aremade of waterproof magnolia wood withferrules of glue-laminated exotic wood.The cutting edge of white paper steel isflanked by soft steel and white papersteel. Hardness approx. 60 HRC, notrustproof, bevelled on both sides.

All knives are supplied with or without awooden sheath as desired.

These knives are made in small series inthe workshop of the imperial supplierKobayashi. The blades have two layers,with a cutting edge of White Paper Steeland bevelled on one side for right-han-ders. The traditional magnolia wood handles are asymmetric so that they fitsecurely in the hand. Not rustproof.Hardness approx. 63 HRC.

2 Sashimi Deluxe (fish knife)

Thick-walled blade for cutting and lightchopping.Blade length 180 mmOverall length 330 mmBlade thickness 9 mm385 g

The best knives from the two masterblacksmiths Hayashi and Kobayashi in asingle set: - 719027 Santoku (all-purpose knife) - 719005 Usuba (vegetable knife) - 719002 Sashimi Deluxe knife (fish knife)- 705886 wooden case

Price advantage

No. 719361 172.18 € 204.90 €

No. 719360 172.18 € 204.90 €

No. 719141 63.45 € 75.50 €

No. 719249 41.93 € 49.90 €

No. 719250 46.13 € 54.90 €

No. 719077 65.13 € 77.50 €

No. 719339 89.92 € 107.00 €No. 719252 46.97 € 55.90 €

No. 719251 53.61 € 63.80 €

No. 719088 122.27 € 145.50 €

No. 719142 45.29 € 53.90 €

No. 719078 65.13 € 77.50 €


188

A TADAFUSA HOCHO

1 Santoku (all-purpose knife)Blade length 165 mmOverall length 305 mmBlade thickness 2.5 mm130 g


3 Sashimi (fish knife)Blade length 165 mmOverall length 305 mmBlade thickness 2.8 mm135 g

5 2-piece set- 719077 Santoku (all-purpose knife)- 719078 Usuba (vegetable knife)- in an elegant gift box

B KURO OCHI HOCHO



4 Herbs KnifeBlade length 90 mmOverall length 205 mmBlade thickness 2.7 mm70 g

5 2-piece set Price advantage

A

B

1

2

3

4

1

2

3

4

C SUIMON HOCHO 1 Santoku (all-purpose knife)Blade length 165 mmOverall length 305 mmBlade thickness 2.5 mm130 g

2 Gyuto (fish and meat knife)Blade length 185 mmOverall length 320 mmBlade thickness 3 mm140 g

C

1

2

Price advantage

4 Ajikiri (trimming knife)Blade length 105 mmOverall length 230 mmBlade thickness 2.8 mm80 g

3 Ajikiri (trimming knife)Blade length 120 mmOverall length 235 mmBlade thickness 3 mm60 g

The interestingly patterned blade is made of Suminagashisteel which has been very carefully,highly polished. The cutting edge ismade out of high-alloy SKD11 steel*with a hardness of 62 Rockwell whichholds an edge perfectly. The core layer issandwiched between two layers of purenickel and stainless steel, a total of 32layers each side. This build up producesthe contrasting blade pattern and leadsto additional breaking strength and rustresistance. The octagonal shape of themagnolia wood handle combined withtwo genuine water buffalo horn bolsterscompletes the perfect look of the knife. *steel analysis: 1.6 % carbon, 13 % chromium, 1 % molybdenum, 0.4 % vanadium

5

5

Hammer marks on the forged skin - Art and handcraft of highutility: The individual traces of the black-smith’s hammer from this traditionalworkshop can be seen in the so-called»forged skin« on the 3-layered blade sur-face. This not only gives the blade a raw,original appearance but also makes it easier to care for, making this double-bevelled knife robust and suitable fordaily use. The cutting edge of non-rust-proof Blue Paper Steel is perfectly pol-ished and sharpened, the outer layers areof rustproof steel. The glue-laminated, exotic wood ferrule provides an attractive visual contrast to the blades. Hardness approx. 63 HRC.

The archetype of the Japanese knife: Each of these 3-layered blades, made according to atraditional design, is personally signed bythe master blacksmith. The cutting edgeof hard blue paper steel (61 HRC) isflanked by tough steel. The black-burnedsurface forms an effective contrast to theferrule of extremely rare, grained buffalohorn and the handle of natural magnoliawood. Not rustproof.

- 719251 Santoku (all-purpose knife) - 719252 Usuba (vegetable knife)


189

No. 719229 12.02 € 14.30 €

No. 719020 11.18 € 13.30 €

No. 719217 12.02 € 14.30 €

No. 719237 71.18 € 84.70 €

A MATSUBA HOCHO B JAPANESE MINCING KNIFEAllows the aroma of herbs to develop:

No. 719253 58.74 € 69.90 €

No. 719196 70.59 € 84.00 €

Price advantage

E SMALL KNIFE, INCL. SHEATHLight-duty knives with rustproof, triple-layered blades and sheaths made ofwater resistant Enju wood. Double-bevelled.

Blade length 105 mmOverall length 220 mmBlade thickness 1.2 mm40 g

2 Fruit KnifeBlade length 100 mmOverall length 200 mmBlade thickness 1.2 mm30 g

3 Vegetable KnifeBlade length 105 mmOverall length 220 mmBlade thickness 1.2 mm40 g

4 Compact Knife Set

No. 719195 36.05 € 42.90 €

A

B

C

E

1

2

34

This knife is forged exclusively for our cus-tomers by our Japanese master. Fitted witha heavy, arched blade it chops all types ofherbs with a rocking cut. Tender stemsand leaves are not squashed but cut to en-hance the flavour. Three-layer steel blade*, ground razor-sharp, surface left in forged condition withburned-in linseed oil (antirust). Every knifeis signed by the master. Magnolia woodhandle with a buffalo horn ferrule, bevel-led on both sides.* Middle layer of blue paper steel, 61HRC, iron outer layers (not rustproof).Blade length 135 mmOverall length 270 mmBlade thickness 6 mm280 g

C ALL-PURPOSE KNIFE WITH SHARP-ENING STONE AND DVDSharp as a razor and almost without re-sistance, the blade of the Santoku withdouble bevel cuts fish, meat and veget-ables equally. The beautifully shapedhandle made of Magnolia wood and ge-nuine buffalo horn ferrule is very comfor-table to hold. A wooden sheath protectsthe blade. In order to keep the valuableknife sharp use the combination sharpe-ning stone together with the instructionon DVD.

1 All-purpose Knife

With this starter kit you are well preparedfor any cutting work. Three compact knivesin an attractive red leather roll-up case:- 719217 All-purpose knife- 719229 Vegetable knife - 719020 Fruit knife

Our Japanese master blacksmith willshow you how to professionally sharpenkitchen knives on water stones. He pre-sents different types of stones, showingmotions and gives care instructions.Santoku Hocho: triple-layered blade, corelayer »Blue Paper Steel«, not rustproof.Sharpening stone: grit 1000/6000. DVD (15 minutes), in German.In a gift box.

A compact filleting knife, used in Japan for small fish andalso for meat. The sleek, Katana-shapedblade has a shearing cutting action. Theextreme sharpness and single bevel allowprecise cutting. 2-layer carbon steel(White Paper Steel cutting edge), notrustproof, forged in a master workshop inTakefu, magnolia wood handle, horn ferrule.Hardness approx. 60 HRC.Blade length 150 mmOverall length 285 mmBlade thickness 4 mm90 g

Messer || Traditional hocho

190

No. 719241 83.19 € 99.00 €

Sharp and good

A SAKU HOCHO

1 Santoku (all-purpose knife)SheathWith No. 719221 28.99 € 34.50 € Without No. 719054 22.27 € 26.50 €

2 Gyuto (fish and meat knife)SheathBlack No. 719222 28.99 € 34.50 €Natural No. 719234 28.15 € 33.50 €Without No. 719068 22.27 € 26.50 €

3 Usuba (vegetable knife)SheathWith No. 719218 28.99 € 34.50 € Without No. 719036 22.27 € 26.50 €

- 719054 Santoku (all-purpose knife)- 705373 Tokico® knife sharpenerNo. 719398 34.37 € 40.90 €

4 3-piece Set in a roll pouch

No. 719385 91.60 € 109.00 €

A

1

2

3

No. 711064 37.65 € 44.80 €

C JAPANESE KNIFE WITH COMBINATION SHARPENING STONEAND SHARPENING PRIMERCooking Knife Starter Set:

D

4

Price advantage

Price advantage

C

B

An uncomplicated knife sharpenerthat is suitable for both Japanese andEuropean knives: Easy to operate, theTokico® allows even inexperiencedusers to quickly and successfullysharpen all types of cooking knives.The blade simply needs to be mois-tened and slid 3-5 times in both di-rections through the slits. Metal isgently removed by two rotating andcorrectly angled stones. Suitable forsingle and double-sided groundknives.Please note: The Tokico® is not suit-able for damaged or worn out blades.

These all-purpose blades are exactly rightfor becoming acquainted with traditionalJapanese knives: The rust-resistant,sharp cutting edge is flanked by two layers of rustproof stainless steel, whichmakes it easier to care for.The handle is of hard, fine quality rosewood.Optionally available with a wooden sheath.


Saku Hocho 3-piece knife set with darkbrown leather roll pouch. Great for sto-rage or as a gift. - 719221 Santoku (all-purpose knife) - 719222 Gyuto (fish and meat knife) - 719218 Usuba (vegetable knife)

B JAPANESE KNIFE SET WITH COMBINATION SHARPENING STONEAND SHARPENING DVD

Razor-sharp cuts forever are almost guar-anteed with this starter set! If necessary,the handy Santoku knife can easily besharpened on the included water stone.The also included Sharpening Primergives instructions on how to proceed.Set includes:- Santoku (all-purpose knife),

Blade length 140 mm, 3-layer steel bladewith carbon steel core (not stainless), plated on both sides with stainless steel, handle and sheath made from bubinga wood.

- Combination stone (711061), grit 1000/3000 for sharpening and finishing, 175 x 55 x 25 mm

- Sharpening Primer

D SAKU ALL-PURPOSE KNIFE WITH TOKICO® KNIFE SHARPENER Price advantage

Celebrate the art of cutting with our ver-satile Japanese knives: A Gyuto for fishand meat, the Usuba for slicing wafer-thin vegetables and for peeling. In orderto help you keep these valuable piecesrazor-sharp, a combination sharpeningstone is included, along with an instruc-tional DVD. The set comes in a beautifulwooden storage case.

Set includes:- 719068 Gyuto (fish and meat knife)- 719036 Usuba (vegetable knife)- 711007 Sharpening stone 1000/6000- 713806 Sharpening DVD (in German)- 705888 Wooden case

Knives || Western design hocho

191

Western design Hocho

Blades from master´s hand

A TAKAMURA HOCHO

1 Santoku (all-purpose knife)

No. 719325 284.87 € 339.00 €

Blade length 165 mmoverall length 295 mmblade thickness 2 mm180 g

3 Sashimi (fish knife)Blade length 270 mmOverall length 395 mmBlade thickness 2 mm200 gNo. 719327 431.93 € 514.00 €

4 Deba

No. 719328 431.93 € 514.00 €

5 2-piece set- 719325 Santoku (all-purpose knife) - 719323 Gyuto (fish and meat knife)No. 719329 542.86 € 646.00 €

1

2

3

4Price advantage

A

Chef's Knives:These knives are characterised by cleardesign and a unique cutting feeling: Thecutting edge of these blades is powdermetallurgical SG-2 steel with a Rockwellhardness of 63 HRC. This metal offershigh wear resistance and extreme hard-ness and sharpness. The particularlyclear aesthetics of this knife are createdthrough a 65-layer Suminagashi blade.Stainless steel fittings, handle scales ofsturdy wood laminate. Double-bevelled.All knives in a lovely, black lacqueredwooden sheath. Stainless.

Thick-walled blade for cutting and lightchopping.Blade length 210 mmOverall length 350 mmBlade thickness 3.5 mm340 g

The combination of Japanese blade quality and Western kitchen techniquesresults in high quality cutting utensils.Comfortable in the hand, outstandinglysharp but easy to care for.

5

2 Gyuto (fish and meat knife)Blade length 180 mmOverall length 310 mmBlade thickness 2 mm175 gNo. 719324 284.87 € 339.00 €

Blade length 210 mmOverall length 340 mmBlade thickness 2 mm185 gNo. 719323 318.49 € 379.00 €





Free lifetime sharpening for premium products



192

Katsuhiro Hocho

1 2 3 4 5

6

A

Price advantage

For the highest standards of use and aesthetics:

6 2-piece set- 719341 Gyuto (fish and meat knife)- 719342 Santoku (all-purpose knife)- casket with sliding lidNo. 719346 533.61 € 635.00 €

1 Santoku (all-purpose knife)Blade length 165 mmOverall length 290 mmBlade thickness 2 mm190 gNo. 719342 310.08 € 369.00 €


These unique kitchen knives are forgedfrom one of the world’s hardest bladesteels. They are characterised not only bytheir phenomenal sharpness and durabil-ity, but also by the fascinating pattern ofthe 65-layer blade (cutting edge of SG-2steel). These masterpieces are perfectedby handles of either water-resistant desertironwood, the densest wood in the world,or of water-resistant black linen Micarta.The polished nickel-silver bolsters har-monise superbly with the ergonomic han-dle. The pinning of the handle scales withrosette-shaped mosaic pins makes theknives real eye-catchers. Despite their topcutting performance, the knives are hard-wearing due to their rustproof blades bev-elled on both sides, and waterproofhandles, making them the first choiceamong professional chefs.Hardness 63 HRC.

A KATSUHIRO HOCHOWITH BLACK LINEN MICARTA HANDLE





193


3 Gyuto (fish and meat knife)Blade length 150 mmOverall length 270 mmBlade thickness 2.3 mm120 gNo. 719257 269.75 € 321.00 €

1 Santoku (all-purpose knife)Blade length 170 mmOverall length 290 mmBlade thickness 2.5 mm190 gNo. 719248 318.49 € 379.00 €

4 Usuba (vegetable knife)Blade length 165 mmOverall length 295 mmBlade thickness 2.1 mm200 gNo. 719259 318.49 € 379.00 €

5 Sashimi (fish knife)For meat and fish.Blade length 210 mmOverall length 330 mmBlade thickness 2.3 mm170 gNo. 719258 360.50 € 429.00 €

6 2-piece set- 719257 Gyuto (fish and meat knife)- 719248 Santoku (all-purpose knife)- casket with sliding lidNo. 719338 562.18 € 669.00 €

B

2 31 4 5

6

Price advantage

B KATSUHIRO HOCHO WITH DESERT IRON-WOOD HANDLE

No. 719297 107.56 € 128.00 €


194

Sharp, for all intents and purposes

A -SERIES »KLASSIK«








9 2-piece set- 719296 Santoku (all-purpose knife) - 719308 Petty (small all-purpose knife)No. 719397 149.58 € 178.00 €

10 5-piece set

No. 705883 578.99 € 689.00 €

1

2

3

4

5

6

7

8

10

Price advantage

Price advantage

9

A

2 Petty (small all-purpose knife)Blade length 80 mmOverall length 185 mmBlade thickness 1.5 mm70 gNo. 719308 49.58 € 59.00 €

Set includes:- 719296 Santoku (all-purpose knife) - 719297 Usuba (vegetable knife) - 719292 Gyuto (fish and meat knife) - 719294 Gyuto (fish and meat knife) - 719295 Gyuto (fish and meat knife) - 705884 precious knife case of laminated birch wood

Classical aesthetics, traditional technology:Perfect, traditional Damascus blades andoptimally balanced handles of brownlaminated exotic wood: Traditional meth-ods result in classical aesthetics for dailyuse. 32 layered Suminagashi steel bladewith a cutting edge of VG-10 steel. Rust-proof. Hardness approx. 62 HRC.


195

2

1

A

Price advantage10








8 Usuba (vegetable knife)

No. 719458 116.81 € 139.00 €

10 2-piece set

No. 719459 192.44 € 229.00 €

3

4

5

6

7

9 Sashimi (fish knife)Blade length 240 mmOverall length 360 mmBlade thickness 2.2 mm200 gNo. 719456 187.39 € 223.00 €


8

9

- 719457 Santoku (all-purpose knife)- 719451 Gyuto (fish and meat knife)- casket with sliding lid

A MATSUNE HOCHOThese all-purpose knives for the daily use have 32 layers of rustproof Suminagashi stainless steeland a cutting edge of VG10 gold steel.Mirror polished blades and handles ofebony-coloured, glue-laminated exoticwood. Hardness approx. 61 HRC.

No. 719254 218.49 € 260.00 €


196



Blade length 80 mmOverall length 190 mmBlade thickness 2 mm70 g No. 719435 37.73 € 44.90 €

5 2-piece set- 719245 Gyuto (fish and meat knife)- 719246 Santoku (all-purpose knife)No. 719255 142.02 € 169.00 €

6 3-piece set- 719245 Gyuto (fish and meat knife)- 719246 Santoku (all-purpose knife)- 719247 Usuba (vegetable knife)

Puristical Classics

B 3D-KNIVES

5 4-piece set- 719436 Santoku (all-purpose knife)- 719437 Gyuto (fish and meat knife)- 719438 Gyuto (fish and meat knife)- 719439 Usuba (vegetable knife)No. 719440 360.50 € 429.00 €

A KUSAKICHI HOCHOTraditional technique, easy to use:


1 2 3 4

A

Price advantage

Price advantage

Price advantage

4 Petty (small all-purpose knife)

Kitchen knives with purist, simplewooden handles are valued for their clear form and light weight. Sometimesreserved, sometimes playful and dramatic but always committed to the traditions of handcraft.

A new dimension of knife handles:




4 Usuba (vegetable knife)Blade length 165 mmOverall length 295 mmBlade thickness 1.7 mm160 gNo. 719439 105.88 € 126.00 €

B

1 2 3 4

5

6

5

These knives can be cared for in thesame manner as Western knives: The cutting edge of rustproof VG10 Gold Steel is surrounded by 16 rustproof Suminagashi layers with a hammeredsurface. Handles of laminated rosewood. Hardness approx. 61 HRC.

These elegant Japanese knives impressby their modern design. The handle ismade from beautifully grained, laminated,exotic wood, its »sharp« design investingthe knife with a very ergonomic grip.

With its beveled end the handle perfectlyfits the heel of the hand, almost like apalm stone. Dark and elegant, the handleencompasses a hand-forged, 32-layerblade of Suminagashi steel. The cuttingedge is forged from VG10 Gold Steel(stainless). These knives are distinguishedby their remarkably light weight. Professional chefs agree that the kniveslie comfortably in the hand and that theyare good and easy to work with. Hardness approx. 61 HRC.


197

No. 719375 192.44 € 229.00 €

No. 719147 75.55 € 89.90 €

No. 719148 75.55 € 89.90 €

No. 719129 74.79 € 89.00 €

A SHIGEKI HOCHOHigh contrast and sharp:




4 3-piece set

No. 719233 203.36 € 242.00 €Similar knives with quince wood han-

dle see www.more-than-tools.de

B ARATA HOCHOArchaic design at a beginner’s price:



A

1

2

3

Price advantage

B

1 3 4 5 6 72

Due to the contrast between the Damas-cus blades and the red sandal wood lami-nated handels these knives are a real eyecatcher. The 32 layers of Suminagashisteel and the cutting edge of VG10 GoldSteel are rustproof. Attractive price/per-formance ratio. Hardness approx. 61 HRC.

Lovely shaped knives with hand-forgedblades of archaic appearance. The cut-ting edge is of Blue Paper Steel flankedby two layers of rustproof steel. Ham-mered surface, handles of thermallytreated bubinga wood. Hardness approx. 63 HRC.

2 Petty (small all-purpose knife)Blade length 90 mmOverall length 195 mmBlade thickness 2 mm50 gNo. 719370 41.93 € 49.90 €




7 Sashimi (fish knife)Blade length 245 mmOverall length 380 mmBlade thickness 2 mm180 gNo. 719374 104.96 € 124.90 €

8 3-piece setSet includes:- 719148 Santoku (all-purpose knife) - 719371 Gyuto (fish and meat knife) - 719147 Usuba (vegetable knife)

Price advantage

8

4

- 719128 Santoku (all-purpose knife)- 719059 Gyuto (fish and meat knife)- 719129 Usuba (vegetable knife)- 705885 Wooden case

No. 719304 32.35 € 38.50 €

No. 708081 25.13 € 29.90 €

No. 708082 50.34 € 59.90 €

No. 719065 20.92 € 24.90 €

Knives || Knives for special applications

198

Knives for special applications

A BREAD KNIFE

F »ONO« JAPANESE KITCHEN FOLDINGKNIVES

1 Santoku (all-purpose knife)Blade length 100 mmOverall length 250 mm (folded out)Blade thickness 3 mm220 gNo. 719286 150.42 € 179.00 €

2 Usuba (vegetable knife)Blade length 100 mmOverall length 255 mm (folded out)Blade thickness 3 mm225 gNo. 719287 150.42 € 179.00 €

D SMALL ALL PURPOSE KNIFE »MIKI«

For more multi purpose knives see www.more-than-tools.de

C TRADITIONAL CHINESE CHOPPING KNIVESApart from the wok, the chopping cleaveris the most important utensil in Chinesecuisine. It is well-suited for chopping andportioning meat and vegetables as wellas finely mincing herbs.

1 Deluxe cleaverThis cleaver from a traditional Shanghaimanufacturer features a high-quality, tri-ple-layered steel blade with an extra hardsteel core offering unsurpassed sharpnessand edge life. The blade, ferrule and tangare forged from a single piece of steel towhich the colourfully accented pakka woodhandle is seamlessly attached. Rustproof.Blade length 185 mmOverall length 310 mmBlade thickness 3 mm430 g

2 Standard cleaverHeavy chopping cleaver for portioningmeat and fish, also suitable for cuttingthin bones. Rustproof blade with a holefor hanging, beech wood handle scalestriple-riveted to a full-length tang.Blade length 175 mmOverall length 290 mmBlade thickness 3.5 mm500 g

A

B

C

1

2

F

1

2

D

E

Long tried and tested, super-sharp Japa-nese serrated knife. It has a long, flexibleblade of solid stainless steel, polished toa fine mirror finish, laminated exoticwood handle. Stainless.Blade length 250 mmOverall length 375 mmBlade thickness 1.3 mm110 g

B SALAMI AND BAGUETTE KNIFEFlexible Blade of 6M steel (hardness approx. 58 HRC) with serrated edge andhand guard. Handle of hammered, satin-brushed stainless steel. The seamlessconstruction ensures the highest level of hygiene. Stainless.Blade length 160 mmOverall length 280 mmBlade thickness 1.9 mm70 gNo. 719158 53.78 € 64.00 €

These practi-cal knives areuseful when-ever cookingunderway.Whether sail-ing or camp-ing, thefolding knivescan be storedin a minimum of space and are well pro-tected when underway. Easy to maintainand a great eye catcher: The blade isfully rustproof, 32 layers of Suminagashisteel surround the cutting edge of VG 10gold steel. The blade latch safely in posi-tion via a Back Lock mechanism. Handlescales of laminated exotic wood, sturdynylon sheath with a belt loop.

Ideally for peeling and cleaning fruit andvegetables and all types of small cuttingtasks in the kitchen. It consists of aVG10 Gold steel cutting edge and stain-less steel outer edges. Rustproof.Blade length 80 mmOverall length 188 mmBlade thickness 1.5 mm60 g

E SIX-PIECE STEAK KNIFE SETHave your steak and enjoy it – with theseaesthetic French steak knives. All knivesfeature specifically serrated edges and anall stainless steel construction, designedto balance comfortably in your hand. This set comes in an attractive gift boxmade of oak wood.Blade length 110 mmOverall length 225 mmBlade thickness 1.5 mm80 gNo. 719336 57.98 € 69.00 €

Knives || Kitchen utensils

199

10 traysWidth 3 x 37 mm, 2 x 44 mm, 3 x 50 mm, 1 x 95 mm, 1 x 105 mmNo. 718981 163.87 € 195.00 €

No. 718990 49.58 € 59.00 €

No. 718992 66.39 € 79.00 €

Kitchen utensils

B KNIFE BLOCKS

1 Knife block, thermo beech

2 Knife block, natural beech

C KNIFE RESTS

C

B

A

1 2

1 2

Knife blocks

A FLEXIBLE KNIFE BLOCKUniversal application:On the one hand it should be handy, on the other hand it has become an attractive kitchen object. This bambooknife block meets both expectations. In contrast to other kinds of wood, high-grade bamboo hardly warps after beingdried. The insert can be removed forcleaning purposes and rearranged in anyorder according to the size and variety of your knives.Practical item: the loose bottom can bereleased very quickly and can be used as a cutting board.

Fine knives should not be stored in a cut-lery box or on a magnetic holder becausethe resulting magnetisation makes sharp-ening more difficult. Instead, we recom-mend these knife blocks speciallydesigned for Japanese Hochos, made inGermany according to our stringent qual-ity criteria. They accommodate 7 kniveswith blades up to 270 mm long and 9mm wide, as well as a pair of scissors.The solid weight provides stability andthe pitched arrangement allows fast ac-cess. The surface is sanded and treatedwith vegetable oil. They are also suitablefor European kitchen knives.

Knife block of thermo beech with mapleinserts. For 7 knives and one pair of scis-sors.* High-temperature treated thermo woodis not only resistant against bacteria andfungal decay, it is particularly stable anddurable.

Knife block of European beech withthermo beech inserts. For 7 knives andone pair of scissors.

A great way to always have your kitchenknives ready at hand: Whether on theworking surface or in the drawer. Theblades are safely separated from eachother thus staying sharper for longer.Available in thermo beech* and naturalbeech, for3 kniveswith bladelengths ofup to 180 mm.* High-temperature treated thermo woodis not only resistant against bacteria andfungal decay, it is particularly stable anddurable.270 x 80 x 43 mm

2 Knife rest, natural beech

1 Knife rest, thermo beechNo. 718997 28.99 € 34.50 €

No. 718994 23.95 € 28.50 €

No. 706034 33.53 € 39.90 €

No. 706036 29.33 € 34.90 €

No. 706037 49.58 € 59.00 €


200

Cutting boards

A ACACIA END GRAIN CUTTING AND CHOPPING BOARD

C ACACIA CUTTING BOARD

B GINGKO CUTTING BOARDRarity:Tough but not too hard, easy on knife cutting edges,good looking and antibacterial,gingko is an ideal wood forcutting boards. This solid board is madeof non-glued, air-dried Japanese ginko,with a planed and untreated surface.360 x 210 x 30 mmNo. 706028 45.80 € 54.50 €

Interesting fact:In Asian mythology, the split leaves ofthe gingko tree symbolise Yin andYang, the balance of all things. Gingkotrees can supposedly reach an age ofup to 4,000 years. The oldest gingkotree in Germany was planted in 1750and stands in the city of Frankfurta.M, in the suburb Rödelheim.

No. 706038 25.13 € 29.90 €

A

B

C

D

E

This gorgeous grained cutting boardmade of hard-wearing acacia wood* setsthe tone in your kitchen. The food safe,glued cross-grained pieces with variedshadowing are especially hard and waterresistant. Brushing with clean water andoiling with vegetable oil will preserve thebeautiful surface of this natural work ofart for a long time.* Acacia wood is not a rainforest woodand is not endangered. This product ismade of plantation wood. 350 x 350 x 30 mm

This massive board made of wonderfullygrained, hard-wearing acacia wood* pro-vides excellent service for all choppingand cutting work in the kitchen. Brushingwith clean water and oiling with vegeta-ble oil will preserve the beautiful surfaceof this natural work of art for a long time.* Acacia wood is not a rainforest woodand is not endangered. This product ismade of plantation wood. 450 x 250 x 20 mm

D CHESTNUT CUTTING BOARDSweet chestnut wood* is tough andhighly water resistant. The heavy boardremains stable when chopping and min-cing. With juice groove.* Antibacterial and antifungal; the chest-nut shingle roof of the Mont Saint-Michelmonastery is over 180 years old. 400 x 300 x 32 mm2.2 kg

E CUTTING AND SERVING BOARDMADE OF BAMBOOElegant and beautiful cutting and servingboard made of bamboo. The dark color ofthe cutting surface comes from a specialheat treatment process which hardensthe wood and makes it wear resistant.465 x 300 x 25 mmapprox. 2.2 kg


201

A JAPANESE CUTTING UTENSILSExcellent kitchen slicers, graters andpeelers from Japanese master black-smiths. Blades of rustproof steel, naturalwood handles.

1 Mini slicerFor ginger, small cucumbers and truffles.90 x 145 mmNo. 719164 10.00 € 11.90 €

2 PeelerFor carrots, radishes and asparagus.73 x 135 mmNo. 719162 8.24 € 9.80 €

3 Peeling slicerFor radishes, cucumbers and root vegetables.50 x 185 mmNo. 719163 9.75 € 11.60 €

5 Cheese grater with spaghetti portionerIdeal for parmesan, pecorino and medium-hard cheese. The grated material lands in adrawer, the grating insert can be removedfor cleaning. A special extra feature: Therounded cutouts in the handle can be usedfor portioning spaghetti.200 x 115 x 85 mmNo. 719167 41.93 € 49.90 €

A

3

5

4

4 Ceramic peelerThis innovative feather-light ceramic peeler peels asparagus, vegetables andfruit effortlessly and without clogging torelease the pure flavour of the food. Thisis due to the blades of zircon ceramic, amaterial that is not only sharper, but alsoretains its cutting edge 10 times longerthan hardened steel. Dishwasher safe.Blade length 40 mm30 gNo. 719185 15.04 € 17.90 €

Peeler, rasps and accessories

No. 705159 41.97 € 49.95 €

B MICROPLANE® 4-SIDED BOX GRATER4 in one:

Fine No. 705153 24.33 € 28.95 € Coarse No. 705154 24.33 € 28.95 €

B

E

F

This 4-sided Box Crater of Microplane®

copes with all tasks due to the cuttingtechnology and the ergonomic design: Blades made of best stainless steel. 4 friction surfaces: Fine, Middle andExtra Coarse graters and one slicer. The fine grater blade can be removed inorder to clean the grater. The razor sharpblades prevent from clogging. Soft gripand skid-proof stands for safety and sta-bility. Dishwasher safe.280 x 130 x 85 mm

E PROFESSIONAL MICROPLANE®

KITCHEN RASPThe dozens of razor-sharp mini planeblades on this rasp will revolutionize theway you grate: Effortlessly transformparmesan, ginger, garlic, nuts and choco-late. The professional stainless steelutensil can be cleaned in the dishwasher.With hanging eyelet.Friction surface 60 x 135 mmOverall length 330 mm

F SLIDER ATTACHMENT FOR KITCHEN RASP

No. 705172 4.16 € 4.95 €

This grater attache-ment allows you tograte even smallpieces safely. Itprotects your fin-gers from injuriesby the sharp blade. Fits all professionalseries rasps.65 x 73 x 60 mm

D PREMIUM MICROPLANE®

ZESTER/GRATERThis stainless steel grater is ideal for grating citrus fruits, garlic, ginger andnutmeg. Ergonomic soft touch handlewith hanging eyelet. Dishwasher-safe.Friction Surface 25 x 200 mmOverall length 320 mmNo. 705181 18.45 € 21.95 €

C MICROPLANE® SLICERThe infinitely adjustable Microplane®

mandolin slicer makes light work of cut-ting vegetables, fruit and cheese. Itsnon-slip rubber feet keep it extremelystable, while the safety grip providesadded protection for your fingers. Dish-washer safe.380 x 110 mmNo. 705182 37.77 € 44.95 €

C

Back sideFront side

D

1 2


202

No. 716249 13.87 € 16.50 €

No. 718137 25.13 € 29.90 €

B POULTRY SHEARSRecommended by French master chefs:Highly durable French poultry shears.The poultry shears are forged in a tradi-tional manner from (non-rustproof) carbon steel, a material that is vastly superior to normal rustproof steels withregard to sharpness and retention ofsharpness. The surface is chromed.Lower jaw is toothed, can be dismantledfor cleaning, folding lock.Blade length 90 mmOverall length 240 mm280 gNo. 718125 55.04 € 65.50 €

C DESIGNER KITCHEN SHEARSExceptionally light Japanese kitchen shearswith a light action. For cutting poultry,fish, herbs and vegetables. Adjustable path, blades of rustproofhardened stainlesssteel. Can be dismantled very quickly for washing. Overall length 205 mmBlade length 75 mm115 g

For more household scissors, see thescissors section.

E BAMBOO VINEGAR (CHIKUSAKUEKI)One of the oldest cleaning agents inJapan, bamboo vinegar can be used forthe following purposes:As a fat-dissolving cleanser (either undi-luted or with water added) in the kitchen,bathroom or workshop. Particularly ef-fective on cutting boards, work surfaces,knife blocks, etc. For eliminating mouldand insect infestations in storage areas,

For more kitchen utensils see www.more-than-tools.de

A FRENCH SOMMELIER KNIVESCHÂTEAU LAGUIOLEThe world’s best sommeliers swear by the Château Laguiole sommelier knives,made in the famous SCIP workshop inThiers, France. The corkscrew with»soul« (internal space between the spi-rals) evenly distributes the pulling forceand prevents the cork from breaking, theleverage is optimally balanced and makespulling easier. Engraved springs.Supplied in an exclusive leather case.Blade length 35 mmOverall length 195 mmBlade thickness 2.5 mm

1 Horn handle No. 709049 102.52 € 122.00 €

2 Stamina handleNo. 709208 102.52 € 122.00 €

Well-made Santoku with a very fine-ground blade of stainless molybdenum-tungsten steel. The blade, bolsters andtang are drop-forged from a single pieceof steel for extra stability and great balance. Handle of laminated wood. LightJapanese kitchen shears for cutting poultryand fish. The rustproof shears can be easily dismantled for cleaning.Santoku: Blade length 170 mmOverall length 285 mmBlade thickness 2 mm145 gShears: Blade length 75 mmOverall length 205 mm115 gNo. 719399 69.66 € 82.90 €

D SANTOKU (ALL-PURPOSE KNIFE)AND KITCHEN SHEARS IN A SET

textiles or Tatami mats. For treatingplants with infested roots or leaves or asa fertiliser; simply add some when wate-ring. For extinguishing unpleasantodours.Not for consumption! Instructions included.500 ml bottle

A

1

2

B

C

D

E


203

A

1 2

The way of teaFor hundreds of years tea has enjoyeda primary place of honour among thefoods of Japan, and the ritual valueplaced on it reaches its pinnacle inthe tea ceremony. Based on the prin-ciples of Zen Buddhism, the utensilsused in the ritual are marked by theirformal simplicity and the highest pos-sible level of craftsmanship.

Tea Bowls and Teapots

A CAST-IRON TEAPOTSEnjoy the simple beauty of Zen-Buddhisttea culture with these teapots by Japan-ese master craftsmen. Precision-castfrom molten iron in a sand mould, theoutsides are black-annealed to protectagainst oxidation, while the insides areenamelled. Includes stainless steelstrainer insert. Note: Unlike Chinesecopies and sim-ilar mass-pro-duced items, the teapots offered here areguaranteed hand-made by Japanese mas-ter craftsmen, with the correspondinghigh standard of quality and workman-ship. The glazes are guaranteed heavy-metal-free.

1 Teapot Zui-UnIn a traditional discus shape. The vividlystructured surface is decorated with apattern of spiral-shaped raised dots manually pressed into the sand mould.Capacity 1.2 litreØ 210 mmHeight 70 mmNo. 820040 117.56 € 139.90 €

2 Teapot Hiragata-ObiFinely patterned, delicate teapot.Capacity 0.6 litreØ 170 mmHeight 60 mmNo. 820025 54.54 € 64.90 €

3 Teapot Katsura*Classic teapot with large volume andtraditional knobbly pattern.Capacity 1.25 litreØ approx. 170 mmHeight approx. 94 mmNo. 820300 116.81 € 139.00 €

4 Teapot TsukiThis elegant, discus-shaped teapot exem-plifies the work of renowned designerHisao Iwashimizu. Its earthy structurehas a bluish patina, and contrasts withthe shiny black handle.Capacity 0.5 litreØ approx. 165 mmHeight approx. 40 mmNo. 820302 74.79 € 89.00 €

5 Teapot Chokaku*Red teapot with black handle. This tea-pot gets its colour from a very elaboratespecialised lacquering technique knownas »yakitsuke«. The delicate black pig-mentation is then applied on top.Capacity 0.65 litreØ approx. 90 mmHeight approx. 100 mmNo. 820307 74.79 € 89.00 €

B TEAPOT STAND KATSURAWith fine knobbly pattern and openingfor tea light.Ø 140 mmHeight 20 mmNo. 820301 12.44 € 14.80 €

C TEAPOT STAND ARAREØ 150 mmHeight 18 mmNo. 820026 16.72 € 19.90 €

D TEAPOT WARMER120 x 120 mmHeight 65 mmNo. 820041 27.31 € 32.50 €

E PLATE WADO*This gently curved cast-irondish is the work of noted Ja-panese designer Hisanori Ma-suda. It’s only on closerinspection that you see the finely workeddetail of the surface structure. For ser-ving cakes/pastries or finger food.275 x 120 x 20 mm900 gNo. 820306 41.93 € 49.90 €

3

4

5

D

C

B

E

* Available from August 2010.


204

A TEA BOWLSOriginally inspired by Korean folk art, theJapanese tea pottery perfected itself fullyover 1000 years. Despite variations instyle and formal differences, the modelfor designing tea bowls was always theperfect beauty of nature.

1 Thin-walled tea bowl (Koshimaru)Crackle glaze was developed in 16th cen-tury Japan in the heyday of tea culture. Aspecial clay mixture and temperaturecontrol during firing produce a network ofrandom cracks. Combined with the opa-que bluish shimmer of the glaze, thisturns the bowl into an exquisite work ofart for enjoying your daily tea ritual. Thisthin tea bowl is completely hand-made.Ø 130 mmHeight 75 mmNo. 820038 50.34 € 59.90 €

2 Crackle-glaze tea bowls, 5-piece setWith their random crackle-glaze effect,these small, reed-green tea bowls arebeautiful to behold. Set of 5 in attractivewooden case.Ø 80 mmHeight 55 mmNo. 820304 33.53 € 39.90 €

3 Tea bowl Chawan*This delicate tea bowl bears the hallmarkof renowned designer Hisanori Masuda,with a simple, harmonious shape that fitsperfectly in your hand. Lime green on theoutside, glazed white on the inside, it turnstea-drinking into a pleasure for the senses.Ø 75 mmHeight 55 mm

No. 820303 12.52 € 14.90 €

B CHERRY BARK TEA CADDYIn the Japanese province of Akita, skilfulcraftsmen have been making enchantingobjects from the bark of wild cherry treesfor over 200 years. This caddy is made ofseveral layers of cherry bark. With asmooth inside and a natural finish on theoutside, it’s both a feast for the eyes anda useful container. The perfectly fittinglid preserves the aroma of the tea. Holds approx. 150 g tea.Ø 80 mmHeight 115 mmNo. 820305 82.35 € 98.00 €

1

3

A

2

B

C CAST-IRON COOKING POTS AND PANSFor over 900 years the Japanese city ofMizusawa has been producing iron uten-sils for the kitchen and for tea culture.During this time the method of produc-tion – pouring molten iron into a sandmould – has hardly changed, and thecity’s reputation for creating objects oftimeless beauty remains.

The traditional pots and pans presentedhere will captivate you with their simpleand practical designs and precise cast-iron finish. The natural casting is black-annealed at 900° for added protectionagainst oxidation. Cast iron has severaladvantages over stainless steel or alu-minium:

- The thicker walls of the vessels retain heat and transfer it evenly to the contents

- Has around three times better heat conduction than stainless steel, so the heat is distributed more evenly in the pot and the contents are also heated through the walls

- Is highly ferromagnetic, therefore heats up rapidly on/in induction ovens

- The pots can also be used with gas cookers and outdoors (with charcoal and open fires)

All pots and pans come with instructionsfor use and care.Not suitable for electric cookers.

1 Rice pot*Compact pot with even release of heatfrom all sides, for cooking perfect ricedishes. Retains heat for over an hour!Ø 210 mmHeight 115 mmCapacitiy 2.5 liters3.2 kg

No. 820320 71.34 € 84.90 €

2 Grill panThanks to its removable handle, this original pan can also be used in the ovenor under the grill. Its textured surface ensures that nothing sticks. Comes withserving board made from flamed cedar-wood. Ideal for preparing and servingshrimp or small fish.240 x 210 x 25 mm1.5 kgNo. 820321 49.50 € 58.90 €

3 Deep pan GurirusukirettoThis pan gives you two cooking utensilsin one: It’s big enough for stewing orsteaming meat or vegetable dishes, but also the 2.6 kg lid can be used as a separate frying pan. Ridges in the baseprevent food from sticking.Lid: Ø 240 mm, height 30 mm, 2.6 kgPan: Ø 240 mm, height 60 mm, 2.8 kgNo. 820322 142.77 € 169.90 €

Cast-iron cookware

D CAST-IRON ROLL MORTARThis utensil is as functional as it is easyto handle. A few rolling movements ofthe cast iron millwheel in the bowl andthe spice grains are ground. Cast in sand,ground by hand to a perfect fit, sandblasted, fire-bronzed with linseed oil to adeep black colour.Manufactured inGermany by hand.Length 120 mm3.3 kgNo. 719178 125.21 € 149.00 €

E BRONZE ROCKER KNIFEThe simple, ergono-mic form and itsperceptible self-weight make therocker knife a plea-sure to use. It is in-dividually cast in sand by means of handmoulding. The specially-composed alloy(high-purity copper, tin and 1% silver) ischaracterised by its fine grain and hard-ness. It does not affect the taste of food,even when grinding hot spices or chop-ping herbs. Length 100 mmThickness approx. 10 mm220 gNo. 719175 115.13 € 137.00 €

For further cast-iron cooking vesselssee www.more-than-tools.de

C

1

2

3

D E



Knives || Hunting and outdoor knives

205

Hunting and outdoor knives

Traditional Japanese knives

»The knife for the lonely wolf.«Manager magazine, 2008

A

2

3

4

5

6

A SAJI'S OUTDOOR KNIVESMasterly composed from classical com-ponents, master knifesmith Takeshi Saji'severyday knives use to cause quite a sensation - not only in Japan. With theirmulti-layered steel blades these knivesare a real feast for the eyes and show animpressive sharpness due to their WhitePaper steel core. The legendary sharpnessand edge life of these knives is hard tomatch. The shape of the handles guaran-tees a comfortable grip and a safe handling- also suited for European hands. Thesolid anchoring of the tang and the antisliphandles make these utility knives ideal

1 Hunting Knife Kawa AkaWith 11-layered Suminagashi blade.Wooden handle with red ray skin wrap-ping. Wooden scabbard with leathermounts, belt loop. Urushi varnishing.Blade length 130 mmOverall length 250 mmBlade thickness 4.7 mm180 gNo. 719268 192.44 € 229.00 €

2 Outdoor Knife BambooWith 11-layered Suminagashi blade.Solid steel, handle wrapped in ray skinand bamboo. Bamboo case with cord.Blade length 145 mmOverall length 250 mmBlade thickness 3.7 mm150 gNo. 719264 209.24 € 249.00 €

even for robust purposes. Great importancehas been attached to functionality and to the fact that you get good value formoney. Every blade shows the hand-engraved signature of the master himself. White Paper Steel core (C = 1.2 %, hard-ness approx. 60 HRC) with outer layersof low-alloy iron, not corrosion-free.

3 Hunting Knife Kawa KuroThis sturdy knife will withstand all chal-lenges during your hunting or trekkingactivities. The handle, wrapped in blackray skin, ensures a secure grip evenunder wet conditions. Wooden scabbardwith leather mounts, belt loop. Gunmetalfinished 11-layered Suminagashi blade.Blade length 110 mmOverall length 230 mmBlade thickness 4.5 mm174 gNo. 719260 192.44 € 229.00 €

4 Konoha HochoPurist:The Konoha Hocho is characterised by aclear form and rustic finish. Powerfulthree-layer blade in a willow leaf form(iron/White Paper Steel/iron), with anakagashi (oak) handle, belt sheath of for-med naturally tanned leather and karabi-ner.Blade length 80 mmOverall length 185 mmBlade thickness 3.5 mm70 gNo. 719139 108.40 € 129.00 €

5 Hocho with Cherry Bark HandleWith this generously dimensioned utilityknife the master blacksmith reanimatesthe traditional art of cherry bark hand-work (Kaba Zaiku). The beautifully grai-ned, breathing skin of the cherry treeadds class to the handle and sheath. Thestrong blade of 11-layered Suminagashisteel is amazingly sharp and durable evenunder the most demanding conditions.Blade length 155 mmOverall length 280 mmBlade thickness 5.5 mm250 gNo. 709036 209.24 € 249.00 €

6 Archaic Outdoor KnifeA strong three-layer blade with a cuttingedge of white paper steel makes thisknife very sharp and durable. The bladeis reliably anchored in the unvarnishedwooden handle by a hand forged ferrule.With leather covered wooden sheath. Blade length 135 mmOverall length 245 mmBlade thickness 5 mm170 gNo. 719280 133.61 € 159.00 €

1

No. 719524 335.29 € 399.00 €


206

A »SHIRO« HUNTING KNIFE, PM STEELComposed with the finest ingredients:

C KITAEJI TSUCHIME 120A jewel of the art of blacksmithing:The Shirogami (White Paper Steel) used forthis masterful hunting knife is extractedwith magnets from the sand of the Hinoriver, smelted in a charcoal furnace andthen forge welded with multi-layer Sumina-gashi steel. Fine hand polishing on naturalstone accents the grain of the multiply fol-ded blade. It is double-bevelled and signedby the master blacksmith. Rosewoodhandle, leather sheath with belt loop.White Paper Steel, not rustproof.Blade length 120 mmOverall length 270 mmBlade thickness 5.5 mm220 gNo. 719034 838.66 € 998.00 €

No. 719215 83.95 € 99.90 €

B HUNTING KNIFE

No. 719284 138.66 € 165.00 €

Whether hunting or trekking, you can rely onthis sturdy outdoor knife even under the hardest conditions. The strong, ergonomicallyshaped beech handle is decorated with orna-mental rivets. The bronzed blade has a corelayer of tough blue paper steel (not rust-proof), is 5 mm thick and hand signed by themaster blacksmith. The meticulously workedrobust leather sheath has two fasteningstraps. It can be worn on a belt.Blade length 160 mmOverall length 280 mmBlade thickness 5 mm280 g

The knife maker undertook intensive research with hunters. The result is thedesign of this very practical knife. It is verylight, robust, very sharp and easy to shar-pen. This makes the combination of BluePaper Steel for the cutting layer and onelayer of low carbon steel on each side. Theblade is Bowie style. Decorative hammermarks are left in the upper area of theblade. The makers signature is partly goldcoloured. Traditional forged iron ferrule witha widely dimensioned guard. The grip ismade of black stained heat treated andbrushed oak wood. Strong thong. No. 709158 104.20 € 124.00 €

The knife comes with a solid saddleleather sheath with a belt loop.Blade length 135 mmoverall length 260 mmblade thickness 4 mm170 g

A B

C

D E

Hand-forged knife with an archaic appea-rance, of 16-layer Suminagashi steel anda core of blue paper steel with excellentsharpness retention (approx. 60 HRC).The red notch is the signature of theblacksmith. Not rustproof. Cord-wrappedhandle, leather sheath.Blade length 90 mmOverall length 230 mmBlade thickness 3 mm130 g

E »KEN NATA« HUNTING AND OUTDOOR KNIFELight, sharp and handy:

The blade of hardest Cowry X PM steel(66 HRC) is embedded in a 64-layerednickel/stainless steel laminate with anexquisite grain. The ironwood handle isfinely decorated with mosaic pins. Nickelsilver hand protection, sturdy leathersheath.The nature of such individual productioncan sometimes result in delivery delays.If so we will immediately inform you. Blade length 110 mmOverall length 230 mmBlade thickness 3.3 mm160 g

D »MORIYUKI« OUTDOOR KNIFE


Free lifetime sharpening for premium products



207

No. 719506 82.35 € 98.00 €

No. 719352 87.39 € 104.00 €

Japanese knives in a Western style

A HIRO® HUNTER SUMINAGASHI

No. 719350 217.65 € 259.00 €

B HIRO® DAMASCUS HUNTING KNIFE,COCOBOLO HANDLE

No. 709047 200.84 € 239.00 €

C HUNTING KNIFE WITH OAK WOOD HANDLEThis exceptional knife features a 4.4-inchSuminagashi bowie blade. The hammeredsurface adds to the archaic appearance.The core layer of Blue Paper Steel is hardand tough at the same time and may behoned to a razor sharp edge. For addedstability and easy-maintenance it is sand-wiched between 40 layers of stainless steel.The Loveless design rivets are made ofstainless steel and brass. This sturdy knife comes with a high-qualitysaddle leather sheath (with belt loop).Blade length 110 mmOverall length 240 mmBlade thickness 4 mm170 gNo. 719349 125.21 € 149.00 €

D HANDY HUNTING KNIFE WITH A QUINCE WOOD HANDLEThe wild quince wood grain handle, withbrass and stainless steel rivets, makesthis knife a work of art for nature lovers.The use of the finest materials and thefine craftsmanship bear witness to thefact that the blacksmith conforms to thehigh standards required for membershipin the American Knifemakers' Guild.Hand guard of nickel silver, blade of rust-proof AUS8 steel, sheath of sturdy natu-ral cow leather with a belt loop.Blade length 100 mmOverall length 210 mmBlade thickness 3.5 mm130 g

The classic hunting knife:The combination of rustproof AUS6mono-steel drop-point blade and fine la-minated wooden handle with nickel silverfittings has proven its worth thousands oftimes. This evergreen hunting knife feelsgreat in the hand and is durable and reli-able in even the most demanding of out-door activities. Leather sheath with a beltloop.Blade length 90 mmOverall length 195 mmBlade thickness 4 mm130 g

A

B

C

D

E

E HIRO® HUNTER

32 layers of rustproof stainless steel and a cutting edge of VG10 steel make thishunting knife a reliable companion for alloutdoor activities. The design of the handlealso shows a perfect symbiosis of functiona-lity and harmonious design. Intensely grained quince wood with nickel silver fittings, leather sheath with belt loop.Blade length 120 mmOverall length 230 mmBlade thickness 4 mm150 g

The ergonomically shaped handle of cocobolo lies comfortably in the hand, thesplendid blade of rustproof Damascus steelwith a core of VG10 Gold Steel (hardnessapprox. 60HRC), rustproof, can also standup to heavy stresses. Strong leather sheathwith a belt loop.Blade length 105 mmOverall length 225 mmBlade thickness 3.7 mm120 g

No. 719571 578.99 € 689.00 €

No. 719572 579.83 € 690.00 €


208

From a German master blacksmith

A HUNTING KNIFE WITH EBONY HANDLEEvery piece is unique:This high quality hunting knife is tradi-tionally forged by hand by a Bavarianmaster forge. The forged blade is madeout of random Damascus, for which 220layers of cold working steel and springsteel have been forge-welded.The elegant and ergonomic ebony handleis shapely framed by knob and studmade out of nickel-silver. Each master-piece will be delivered in a saddle leathersheath with integrated belt loop.Blade length 90 mmOverall length 205 mmBlade thickness 3 mm90 gNo. 719570 377.31 € 449.00 €

C HAND-MADE FISHERMAN'S KNIFEThis classically beautiful fisherman's knife is captivating in its har-mony of design and material. Each pieceis unique and was made completely byhand in a German master forge. The blade is made of 65 layers of Japa-nese multi-layer steel, with a cuttingedge of legendary SG2 powder steel andouter edges of stainless steel and purenickel (62 HRC, stainless). The bolsterpairs and rivets are also made of stain-less steel and are thus a perfect match.The versatility of this reliable outdoorknife is impressive. Due to their weight,the rear bolster pairs can be used to killthe fish. The understated sheath is made of twoparts with a clever design: To stun thefish, you pull the knife out of the holderincluding the blade protector, thus pro-tecting the hand. The handle shells aremade of hard-wearing, stabilised camelbone. Even when wet, this masterpieceprovides a good and secure grip. Hand-made leather sheath made of robustcowhide, with belt loop.Blade length 105 mmOverall length 215 mmBlade thickness 2.5 mm160 g

B HUNTING KNIFE WITH IBEX HORN HANDLEThis limited-edition hunting knife is captivating in its skilled work-manship and sophisticated design. Thehigh-contrast blade is made of hand-forged wild damast laminated from 220 layers of cold work steel and spring steel(59 HRC). The blade is therefore notrustproof, but is very easy to sharpen andyields an excellent lasting sharpness. The two bolster pairs and the rivets aremade of stainless steel, while the handleshells are made of polished ibex horn, ahighly limited material. Because of this, the knives are only ma-nufactured in a low-volume and limitededition. The hand-made sheath is madeof hard-wearing cowhide.Blade length 95 mmOverall length 200 mmBlade thickness 3 mm150 g

A

B

C

To stun the fish, pull the knife out of the holder including the blade protector, thus protecting the hand.


209

No. 709060 52.02 € 61.90 €

No. 709093 66.39 € 79.00 €

No. 709044 75.55 € 89.90 €

1 Striped DamascusBlade length 88 mmOverall length 200 mmBlade thickness 4 mm100 gNo. 709061 221.85 € 264.00 €

2 Rose Damascus steelBlade length 88 mmOverall length 200 mmBlade thickness 4 mm100 gNo. 709103 221.85 € 264.00 €

Nordic hunting and outdoor knives

A SWEDISH »DAMASCUS« HUNTINGKNIVESExclusive Nordic style knives for deman-ding requirements: The vividly grainedblades of rustproof Damascus steel arevery wear-resistant. Stained masur birchand reindeer horn handles with a brasshand guard and leather sheath.

B ELKRobust outdoor knife with rustproofSandvik 12C27 blade. Stained and oiledmasur birch handle and reindeer hornferrule with a hand guard. Leather sheathwith a belt loop.Blade length 100 mmOverall length 205 mmBlade thickness 2.5 mm100 g

D FOX

21

B C

D

A

Swedish utility knife with a sharp carbonsteel blade (Uddeholm No. 1770, notrustproof), handle of Nordic masur birch,reindeer horn and brass fittings. En-graved case of vegetable tanned leather. Blade length 100 mmOverall length 205 mmBlade thickness 2.5 mm100 g

A diamond sharpener with a fine and coarse side touches up your knife wher-ever you are and whenever you need it..Sharpener may be stored inside the sheath.Knife blade length 95 mmOverall length 210 mmBlade thickness 3 mm100 g

C NORDIC HUNTING KNIFE WITH DIAMOND SHARPENERIdeal outdoor set - always sharp:Knives with the typical Nordic designhave been made for centuries in theArctic tundra. Experiences from dailyusage under harsh conditions have crea-ted and formed these knives. The outdoorknife features a stainless 12C27 steelblade (57 HRC) and a handle of oiledmasur birch with reindeer horn ferrule –all materials are from Sweden and thesurrounding nature.

No. 709095 41.93 € 49.90 €

E FISHERMAN’S KNIFEFor filleting fish. Sleek, flexible blade ofrustproof Sandvik 12C27 steel. Birchhandle and reindeer horn ferrule withhand guard. Leather sheath with a beltloop.Blade length 125 mmOverall length 245 mmBlade thickness 1.2 mm60 g

E


210

B BRUSLETTO®

OUTDOOR KNIFE ROGNALDThis classical Nordic knife was developedover 100 years ago by Rognald Brusletto,the founder of a blade foundry that isnow well known far beyond the borders ofNorway. The compact form makes it ex-tremely durable, easy to carry and suit-able for wood carving. Rustproof Sandvik12C27 blade, incl. leather sheath with abelt loop. No. 708897 62.18 € 74.00 €

No. 708890 8.32 € 9.90 € No. 718961 70.59 € 84.00 €



D OUTDOOR SET

C FIRE STICK (WILDMARKSSTICKAN)Essential for every trekking tour:When your matchesand lighter let youdown, then you can al-ways rely on the firestick to provide youwith a warming camp-fire. Simply rub anysteel blade across thefire stick to create a burst of sparks largeenough to easily light dry paper or kindling.

A

A WILDERNESS/BOARIdeal for hunting and trekking: robust,rustproof Sandvik 12C27 blade, ergo-nomic handle of stained masur birch,brass hand guard, leather sheath withbelt loop.

B

C

D

Price advantageThree things that people need for theiroutdoor activities: Brusletto outdoor knifewith a rustproof Swedish steel blade anda leather sheath that can be carried on abelt, the ultra-compact Japanese wire

Blade length 65 mmOverall length 170 mmBlade thickness 3 mm80 g

saw that, despite of a weight of only 12 g,can saw arm-thick branches, and a firestick that generates copious sparks whenstroked along a knife blade.

Magnesium stick with a reindeer hornhandle, approx. 10 cm long. With instruction booklet.

No. 709042 124.37 € 148.00 €

No. 719232 152.94 € 182.00 €

Japanese Folding KnivesE MCUSTA® FOLDING KNIVESThe perfect pocket knife consists of qual-ity without compromise, Japanese tradi-tion, a touch of high technology and adash of cult status. This exceptionalcombination, and the exotic handle ma-terials and designs, have made the nameof Mcusta well known all over the world.

1 Katana3-layered blade, Suminagashi handle scaleswith diamond-like pattern and through-holes, very similar in appearance to a tradi-tionally wrapped Katana handle, with case.

No. 719231 184.03 € 219.00 €

2 AloaAloa coloured micarta handle scales withbelt clip, without case. Finest quality 65-layer rustproof Suminagashi steel, blademounted free of play in Teflon bearings,can be dismantled for cleaning.Blade length 70 mmOverall length 170 mmBlade thickness 3 mm65 g

G HIRO® SUMINAGASHI FOLDING KNIFE

1 CocoboloHandle scales of polished cocobolo.Blade length 75 mmOverall length 175 mmBlade thickness 3 mm100 gNo. 719224 116.81 € 139.00 €

2 Deer hornHandle scales of Japanese deer horn(Ojika).Blade length 75 mmOverall length 175 mmBlade thickness 3 mm120 gNo. 719202 141.18 € 168.00 €

F DEER HORN BXD SUMINAGASHIFOLDING KNIFEThe 17-layer Suminagashi blade in »pike«form, slip-proof deer horn grip plates andnickel silver flanges make the BXD notonly a feast for the eyes but also an idealcutting tool for demanding outdoor use.3 mm thick blade, sturdy leather beltsheath.Blade length 100 mmOverall length 225 mmBlade thickness 3 mm185 g

E

1

2

F

G

1

2

Fine knives with eye-catching blades ofrustproof, wonderfully patterned Sumina-gashi steel from traditional Japaneseblacksmith. The typical wave patterns inthe 3 mm blades of 17-layer TakefuVG10 steel are a real eye-catcher, andthe handles of natural materials form astylish contrast to the blades. Solid case.Blade with spring lock and double cam(no impact when folding closed). With aleather sheath.

Blade length 70 mmOverall length 170 mmBlade thickness 3 mm80 g

For more interesting pocket knives see www.more-than-tools.de


211

No. 709034 41.93 € 49.90 €

No. 719400 67.14 € 79.90 €



2 Blade length 70 mmOverall length 175 mmBlade thickness 3 mm105 gNo. 719514 73.53 € 87.50 €

3 Blade length 95 mmOverall length 230 mmBlade thickness 3 mm190 gNo. 719515 83.95 € 99.90 €

A »NORTH MAN« FOLDING KNIFEThese hand forged blades stand up to theheaviest demands. The mechanics andback-lock are solidly made and show nosigns of wear even after years of use.Blades of rustproof Hitachi GIN1 steel,walnut handle scales. With a leather sheath.

B »IC CUT« POCKET KNIFEThis pocket knife is finely polished andcarefully finished with the finest details.The forged blades of rustproof Hitachisteel (AUS 6) are razor sharp and moun-ted in a polished nickel silver housing.Double cam locking system (to preventthe cutting edge from damage whenfolding the knife).

1

2

3

A

E

C ELEGANT FOLDING KNIFEAesthetic and elegant:Back Lock pocket knife in an unusualcombination of materials. The handlescales of finely patterned micarta arereminiscent of ivory and harmoniseperfectly with the rustproof stainlesssteel flanges and brass plates. Theblade is made of ATS 34 steel.

Handle scales of waterproof,glue-laminated exotic wood.With a leather sheath.

The handle scales are outstandinglysuitable for scrimshaw decoration.Blade length 60 mmOverall length 150 mmBlade thickness 2.5 mm50 g

No. 709010 54.54 € 64.90 €

D FOLDING KNIFE WITH INTEGRATED SAWAs a true all-rounder the combi-knife ac-companies you on all outdoor activities.The handle scales of cocobolo wood con-ceal a sturdy knife blade of rustproof toolsteel and a saw blade with an appropriatetooth size. The blade axis can be adjus-ted to prevent lateral play of the blade.The knife is carried in a bag of soft blackleather with a draw string.Blade length 100 mmOverall length 225 mmBlade thickness 2 mm145 g

D

1 Without caseNo. 719069 16.72 € 19.90 €2 With a soft leather sheathNo. 719070 20.59 € 24.50 €3 With a stiff leather folding sheathNo. 719073 24.03 € 28.60 €

Higonokami pocket knivesThe archetypal folding knife:The Higonokami is the archetypal foldingknife and has been manufactured in thetraditional manner for over a century. Thetriple-layered carbon-steel blade (BluePaper Steel) is shaped like a Samuraisword. The handle is made of foldedsheet metal and is opened with the »ear«,the forged lever tang.

F HIGONOKAMI BURASUHandle of folded brass plate.Blade length 80 mmOverall length 165 mmBlade thickness 3 mm40 g

1F

2

G HIGONOKAMI KUROHammered surface, handle of galvanisedsteel plate, black paint with gold inlayson both sides.Blade length 80 mmOverall length 165 mmBlade thickness 3 mm45 gWithout caseNo. 719074 14.96 € 17.80 €With a soft leather sheathNo. 719075 18.40 € 21.90 €With a stiff leather folding sheathNo. 719076 22.44 € 26.70 €

I MINI HIGONOKAMIThis fully functional miniature version ofthe Japanese Higonokami will not onlyenrich any knife-lover's collection but isalso a useful daily companion. Blade of triple-layeredsteel (not rustproof),simple finish, brass platehandle.Blade length 40 mmOverall length 90 mmBlade thickness 2.45 mm16 gNo. 709043 8.32 € 9.90 €

I

No. 719072 7.90 € 9.40 €

H FOLDING LEATHER CASE

3

G

H

B

C

E »ABALONY« MINI FOLDING KNIFEThis Japanese minifolding knife withhandle scales ofcoloured abalone isa real jewel. Thelockable blade of highest quality Gin1steel (59 HRC, rustproof) is impressivelysharp. This knife will be your constantcompanion as a fine key ring or a pieceof jewellery.Blade length 35 mmOverall length 85 mmBlade thickness 1.95 mm20 g

2.5 mm thick leather, vegetable tanned. Serves asa comfortable handle whenthe knife is in use.For Higonokami pocket knivesNo. 719069 and 719074.

No. 709204 37.73 € 44.90 €

No. 709168 18.49 € 22.00 €

No. 709279 32.77 € 39.00 € No. 709280 49.58 € 59.00 €


212

European folding knives and knife pendants

A FALCON® FOLDING KNIVESThese high quality yet inexpensive fold-ing knives have been made by a familycompany in the Italian knife metropolisof Maniago for nearly 100 years. Thesereliable and attractive utility knives aremanually produced under the trade nameof »Falcon«. All blades have a reliablespring locking mechanism. Blade mate-rial: back-lock, rustproof tool steel, approx. 58 HRC. All Falcon knives aresupplied in a sturdy cordura case.

2 Hunting Knife 165/3Hefty knife with gutting blade and saw.Formed linen micarta handle scales, ni-ckel silver flanges.Blade length 80 mmOverall length 180 mmBlade thickness 2.9 mm190 g

1 Sport Knife 165/1.0Strong knife with formed olive woodhandle scales, stainless steel flanges.Blade length 80 mmOverall length 180 mmBlade thickness 3 mm110 g

B MERCATOR® POCKET KNIFEThis folding knife is an icon of Germanknife design and has been produced al-most unchanged since the era of EmperorWilhelm II. Light and compact (only 7 mmthick) but almost indestructible, it is areliable companion for all outdoor acti-vities. The spring lock and hand guardoffer a high level of safety, even under

D TRATTENBACHER FOLDING POCKET KNIFEThe Löschenkohl factory in Trattenbach is a relic of the once blooming foundryindustry in Lower Austria. The folding pocket knives have been ideal bread knives since the 16th century, buthobbyists, hikers and craftsmen alike canalso appreciate these rustic folding knives. No. 719149 4.12 € 4.90 €

F KNIFE PENDANT WITH LEATHER SHEATHHand-forged and fully functional:This beautiful knife made out of carbonsteel (approx. 61 HRC) is completelyhandcrafted. Its ancient design makes itvery attractive and it is also fully functio-nal. The dark scaled surface of the metal No. 719707 33.53 € 39.90 €

C FOLDING KNIFE »PAPERSTONE«Functional and original in design andmaterial:Its extraordinary design renders this knifeunique and practical at the same time.The details are convincing: The handle ismodeled on that of a razor, the lock isformed like a sphere that snaps into posi-tion in the groove designed for this pur-pose, and the material used for thehandle is »Paperstone«. Paperstone isproduced from recycled paper, withoutany formaldehyde added. Mixing thepaper with natural resins results in a very

A

2

1

B

C

D

F

the hardest use (e.g. carving). C-75 carbon-steel blade, steel plate handle, painted black, hanging eyelet.Blade length 85 mmOverall length 200 mmBlade thickness 2.7 mm75 g

tough material that is absolutely scratch-proof, food-safe, and very hard. Theblade is made of stainless Sandvik steel12C27. The knife comes with a leathercase. Produced in the knife-making centreof France in Thiers.Blade length80 mmOverall length205 mmBlade thickness2.5 mm70 g

Original shape, with turned beech handleand wide roof-shaped blade. Rustproofblade, approx. 50 HRC, simple finish.Blade length 75 mmOverall length 178 mmBlade thickness 0.8 mm30 g

E DOUK-DOUKThe functional, affordable and durableDouk-Douk developed into an icon of knifedesign in the last century. Originally developed in 1928 for the French coloniesin Africa and Asia, this knife has beennumerously copied but the originals offered here have unmistakable characte-ristics. Blade of XC70 carbon steel hardened to 53 Rockwell, lightly hollow-ground to be razor sharp, rear edge withfinger grips, the side plates are decorati-vely etched. The handle scales of foldedseam gunmetal plate have a convex formso that they sit better in the hand. Embossed with the symbol of the shaman for luck. To avoid injuries, thestrong XC48 steel spring can also be

1 SmallBlade length 68 mmOverall length 160 mmBlade thickness 2.5 mm40 gNo. 709300 11.43 € 13.60 €

2 MediumBlade length 83 mmOverall length 200 mmBlade thickness 3 mm70 gNo. 709301 15.13 € 18.00 €

1

2

E

latched in the middle position when fol-ding the blade. Made by the 4th genera-tion of Pierre Cognet in the French knifemetropolis of Thiers. Not rustproof.

is a nice contrast to the light brown leath-er sheath. This leather sheath, with in-tegrated cut protection, made out of highquality, plant tanned leather, is soft tothe touch and absolutely skin-friendly.Overall length 95 mm


213

No. 709217 104.20 € 124.00 €

No. 709218 83.19 € 99.00 €

No. 709056 58.74 € 69.90 €

No. 709055 67.14 € 79.90 €

ARTO Folding Knives Laguiole and BirdA French company of long tradition,ARTO has been producing premiumknives, kitchen cutlery, and fine table-ware since 1945. For several years now the company has been well known,among others, for its series of elegant,superior pocket knives, Laguiole and Bird.

A LAGUIOLE FOLDING KNIVESThe Laguiole folding knife is an icon ofFrench design. The trademarks of thisclassic knife are the ergonomic shape ofblade and handle, the »Bee« stop andthe fine engraving on the spring. AllLaguiole »L`Aiglon« handles have the tra-ditional »Shepherd`s cross« of fine brassrivets or silver nails. Shepherds bringingtheir flocks to the Auvergne highlandsused to stick the blade into the groundand pray in front of the cross.Each knife is delivered with a leathercase.

1 Model »Ebène«

No. 709050 58.74 € 69.90 €

Ebony wood handle with brass liners andrustproof blade of Sandvik steel 12C27.Blade length 90 mmOverall length 220 mmBlade thickness 3 mm100 g

4 Model »Buis«Forged blade of non-rustproof, carbonsteel that sharpens well and fine polish-ed french boxwood handle scales withbrass liners.Blade length 90 mmOverall length 220 mmBlade thickness 3 mm90 g

2 Model »Tire-Bouchon«Finely polished ebony handles scales,blade and corkscrew of rustproof Sandviksteel 12C27, polished stainless steel liners.Blade length 85 mmOverall length 200 mmBlade thickness 3 mm90 g

5 Model »Pointe de corne«Elegant folding knife of excellent work-manship with handle scales of polishedcow horn tips. Spring and »Bee« are forged from a single piece and the elegantpattern on the blade and spring back arehandmade. Blade of rustproof Sandviksteel 12C27.Blade length 90 mmOverall length 220 mmBlade thickness 3 mm70 g

3 Model »Amourette«Fine scales of gorgeous grained snake-wood give this Laguiole knife an indivi-dual and exclusive character. Spring and»Bee« are forged from a single piece andthe elegant pattern on the blade andspring back are handmade. Blade of rust-proof Sandvik steel 12C27. Stainlesssteel liners.Blade length 90 mmOverall length 220 mmBlade thickness 3 mm90 g

B FOLDING KNIFE BELT POUCH

No. 709227 7.48 € 8.90 €

A

B

3 4

2

5

1

C »BIRD« FOLDING KNIVESPrecious materials, stunning aesthetics,and perfect functionality are the outstan-ding characteristics of these extraordi-nary folding knives. The handle has theshape of a bird, the pivot head is design-ed like a bird’s head. When the knife isopened at a 45-degree angle, the silhou-ette of a bird with a long beak will ap-pear. The knives feel comfortable in thehand due to their light and ergonomicgrip and guarantee a pleasant handling.Blades made out of rustproof Sandvik12C27 steel.Blade length 90 mmOverall length 220 mmBlade thickness 2.5 mm

3 Model »Bois de Rose«The bird form handle is made of awrought aluminum-copper alloy, a mate-rial also used in aviation. The advantage:It will not dull as quickly as regular alu-minum, and it is much easier to polish.Each and every knife handle is polishedto a mirror finish by hand. The rosewoodinlay additionally makes for a true jewel.90 gNo. 709207 100.00 € 119.00 €

* Paperstone is produced from recycledpaper, which is mixed with natural resins,without adding any formaldehyde. It ishighly scratch-proof, hard, and food-safe.

1 Model »Laiton«Handle made out of black ebony Paper-stone* material. The brass inlay is elegantly matt finished by hand.80 gNo. 709205 92.44 € 110.00 €

2 Model »Cade«Handle made out of black ebony Paperstone* material.Corsican pepper wood inlay.80 gNo. 709206 100.00 € 119.00 €

C

1

2

3

Belt Pouch made from high-quality cowleather, with snap fastener. Fits all La-guiole L'Aiglon and Bird folding knives.


B LEATHER ROLL-UP CASE FORSTRAIGHT RAZORS OR FOLDING KNIVESExclusive and space-saving, this roll-upcase of fine brown calf leather providessafe and compact storage for straight ra-zors or folding knives and is convenientfor travellers to use. It is rolled and fas-tened with two leather straps and can behung on a hook using the leather loop. Itwill accommodate up to 7 razors and/orfolding knives. Hand-made in France byThiers Issard.365 x 210 mmNo. 709154 52.94 € 63.00 €

No. 709233 217.65 € 259.00 €

No. 709235 217.65 € 259.00 €

No. 709267 146.22 € 174.00 €

3 1515S Spalted stabilized beech

No. 709234 209.24 € 249.00 €

No. 709264 234.45 € 279.00 €

No. 709260 158.82 € 189.00 €

A FOLDING KNIVES BY MANU LAPLACEClean, elegant design without unneces-sary frills - the French master ManuLaplace makes folding knives of timelessbeauty and uncompromised functionality.In his foundry in French Thiers he makestwo series of knives. These small worksof art made of the finest steels andwoods are a pleasure to touch and lookat. The compact knives in the 1515S se-ries are inconspicuous companions andthe 1515 series consists of full-sized all-purpose knives. Blades of rustproofSwedish steel 12C27 (58 HRC),mounted in Teflon bearings, reliableliner-lock locking principle.

In a gift case.

1 1515S MammothHandle scales of mammoth tusk pieceswith a vivid grain telling a ten thousandyear old story. Circular patterns arehoned into the surface of the housingand the blade tang (Bouchonnagetechnique).Blade length 60 mmOverall length 160 mmBlade thickness 2.5 mm80 g

2 1515S OlivewoodPolished handle scales of vividly grainedolive wood, plain spring.Blade length 60 mmOverall length 160 mmBlade thickness 2.5 mm70 gNo. 709271 121.85 € 145.00 €

A

For more interesting pocket knivessee www.more-than-tools.de

Beech wood handle shells made of spal-ted stabilized end grain. Radial cuttingmakes a feature of the growth rings,which give a stunning appearance. Theback spring is hand-engraved in detail,while the hollowed spaces create a three-dimensional effect. This knife is a truerarity!Blade length 60 mmOverall length 160 mmBlade thickness 2.5 mm70 g

214

B

2

3

Polished, black water buffalo-hornhandle scales and head plate.Blade length 80 mmOverall length 200 mmBlade thickness 3 mm130 g

4 1515 Buffalo Horn 5 1515 SnakewoodHandle scales of exotically grained snakewood from the South American Republic of Surinam, hand-engraved spine.Blade length 80 mmOverall length 200 mmBlade thickness 3 mm130 g

7 1515 Ebony wood/mother of pearlHandle shells of ebony wood decorated with 3 mother of pearl inlays.The slightly curved back spring looks likea bangle and is engraved with 3 featherson the inside.Blade length 80 mmOverall length 200 mmBlade thickness 3 mm120 g

6 1515 Spalted beechHandle shells made of spalted beech. The back spring is hand-engraved in detail, while the hollowedspaces create a three-dimensional effect.Blade length 80 mmOverall length 200 mmBlade thickness 3 mm110 g

6

4

1

5

7

Knives || Blades and blade blanks

215

Blades and blade blanks

For Japanese kitchen knivesMulti-layered steel blanks with a core ofWhite of Blue Paper Steel, hardened toapprox. 61 HRC and annealed in the

A SANTOKU SHAPEFor All-Purpose Knives. White PaperSteel core. Double-bevelled.Blade length 165 mmOverall length 240 mmBlade thickness 1.5 mm

1 Blade blank with black forged skin, 3 layersNo. 719553 36.30 € 43.20 €

2 Blade blank, 15 layersNo. 719555 58.74 € 69.90 €

Finished blade, 15 layersNo. 719557 70.17 € 83.50 €

B USUBA SHAPEFor vegetable knives. White Paper Steel Core. Double-bevelled.Blade length 165 mmOverall length 240 mmBlade thickness 1.5 mm

1 Blade blank with black forged skin, 3 layersNo. 719554 36.55 € 43.50 €

2 Blade blank, 15 layersNo. 719556 58.74 € 69.90 €

Finished blade, 15 layersNo. 719558 70.17 € 83.50 €

C AJIKIRI SHAPEFor small chopping and rocker knives. Blue Paper Steel Core, 3 layers, double-bevelled.Blade length 110 mmOverall length 170 mmBlade thickness 3 mmNo. 719539 25.13 € 29.90 €

D SASHIMI SHAPEFor fish knives in a willow leaf shape. White Paper Steel Core,2 layers, right-bevelled.Blade length 200 mmOverall length 300 mmBlade thickness 3 mmNo. 719542 58.74 € 69.90 €

For Japanese hunting and outdoor knives

E HUNTING KNIFE SHAPEFor hunting and outdoor knives. Forgedand pre-ground, core of white papersteel, 3-layer, double-bevelled, withgrooved blade. Not rustproof.

Blade length 180 mmOverall length 290 mmBlade thickness 5.5 mmNo. 719544 88.82 € 105.70 €

G SMALL MULTI-LAYERED BLADEBLANKThis blade is perfectly suited to build apendant or carving knife. The core layerof White Paper Steel is sandwiched be-tween 30 layers of Suminagashi steel. Asall blades are handmade, they can varyslightly with regard to form and size.

Blade length approx. 50 mmOverall length approx. 85 mmNo. 709290 13.36 € 15.90 €

Blade length approx. 30 mmOverall length approx. 90 mmNo. 709291 13.36 € 15.90 €

H SMALL TRIPLE-LAYERED BLADE BLANKThe blade is well suited to make a knifean every day companion, a neck knife ora little hunter for the smaller tasks in theforest. Three-layered blade with a cuttinglayer of White Paper Steel. The rough forged surface of the upper part of the No. 709292 13.36 € 15.90 €

Western design knife blades

I SWEDISH DAMASCUS BLADESMagnificently structured, rustproof Dam-ascus blades, manufactured using powdermetallurgy sintering and forging, approx.120 layers. Hardened and annealed,martensitic structure, approx 60 HRC.

1 Striped DamascusBlade length 100 mmOverall length 155 mmBlade thickness 3.3 mmNo. 709092 109.24 € 130.00 €

2 Rose Damascus steelBlade length 88 mmOverall length 146 mmBlade thickness 3.3 mmNo. 709104 109.24 € 130.00 €

3 »Damascus« Carving BladeStriped Damascus steel blade for a smallcarving knife.Blade length 35 mmOverall length 60 mmBlade thickness 2 mmNo. 709105 40.17 € 47.80 €

blade gives an attractive contrast to thefine polished cutting layer. Rockwellhardness 61 HRC. Not stainless.Blade length 80 mmOverall length 135 mmBlade thickness 3 mm

Rockwell hardness 62 HRC. Not rustproof.Blade thickness approx. 3 mm

J BLADES FROM SWEDISH MASTERBLACKSMITHSHand forged blades of the finest Swedishball-bearing steel (not rustproof), excel-lent sharpness retention, highly resilient,61 Rockwell. Not rustproof.Blade thickness 3 mm



A

1

C

D

E

G

H

I1

2

J

3

tang region. The blades are not rustproof.Dimensions are approximate. Suppliedwith working instructions.

2

1

B

2

Knives || Blades and blade blanks

216

A OUTDOOR BLADESNorwegian blades for building knives foroutdoor use. Manufactured in traditionalshapes using Uddeholm steel, hardenedto 57 Rockwell and sharpened for use.

1 Rustproof chromium steel(0.6% C, 13.5% Cr)Hardness 58 HRC.Blade length 130 mmOverall length 245 mmBlade thickness 2 mmNo. 709107 28.49 € 33.90 €

2 Carbon steel, not rustproof(0.7% C, 0.3% Si, 0.5% Mn)Hardness 59 HRC.Blade thickness 2.8 mm



B FROSTS/MORA BLADESThree-layer carbon steel, for making carv-ing or outdoor knives. Middle layer hard-ness approx. 61 Rockwell, highendurance, sharpens well, not rustproof.Blade thickness 2.6 mm

3 Blade length 75 mmOverall length 160 mmNo. 709212 13.87 € 16.50 €



1 Blade length 60 mmStraight blade.Overall length 170 mmNo. 709210 15.04 € 17.90 €

2 Blade length 60 mmCurved blade.Overall length 170 mmNo. 709211 11.51 € 13.70 €

C CARBON STEEL BLADESUddeholm mono steel No. 1770, (0.7% C, 0.3% Si, 0.5% Mn), very sharp, not rustproof.Blade thickness approx. 2.5 mm

D CHROMIUM STEEL BLADESRustproof, martensitic Sandvik steel12C27, (0.6% C, 13.5% Cr), tough and hard-wearing.









E BRUSLETTO KNIFE BLADE BLANK,TROLLUNGENShort blade, ideal for a carving knife.Blade made of rustproof Sandvik Steel12C27, hardened to approx. 58 HRC,pre-ground and tempered. Blackened surface.

No. 709126 14.20 € 16.90 €

Blade length 52 mmOverall length 90 mmBlade thickness 2 mm

Damascus Blade BlanksThese beautifully structured damascusblades with 192 layers are made in theIndus Valley. In order to achieve a highcutting performance, low alloy 1095*carbon steel is forged irrevocably withNickel steel 15N20*. All blanks are already etched and hardened to 60 HRC.

F ROUND STICK TANG BLADE BLANKSBlade blank for a Bavarian style hunterwith a stick tang (round). Random Dam-ascus. The blade blanks are drop-forged.Blade thickness 4 mm



G STICK TANG BLADE BLANKSBlade thickness 3 mm

3 Rose DamascusBlade length 120 mmOverall length 195 mmNo. 719317 61.85 € 73.60 €

4 Ladder Damascus Blade length 95 mmOverall length 175 mmNo. 719318 54.54 € 64.90 €


2 Random DamascusBlade length 105 mmOverall length 180 mmNo. 719316 39.75 € 47.30 €

H FULL TANG BLADE BLANKSPre-drilled tang holes (2.5 mm), thongtube hole 6 mm.Blade thickness 4 mm

2 Rose DamascusBlade length 75 mmOverall length 190 mmNo. 719416 65.80 € 78.30 €


For more full tang blade blanks seewww.more-than-tools.de

A

1

2

B 1

2

3

4

5

C

D

E

F

1

2

3

The edges are not completely sharpened.As these not-rustproof blanks are entirelyhandmade, each is unique. They mayvary slightly in form and size.Analysis: (*1095: C 0.95%; *15N20: C 0.75%, N 2%, M 0.4%)

1 Random DamascusBlade length 100 mmOverall length 215 mmNo. 719415 46.13 € 54.90 €

4

1

2

3

G

H

Knives || Knife kits

217

Knife kits

Folding knives

A SUMINAGASHI BACK LOCK FINE FOLDING KNIFE KIT

Create a knife with an impressively etched33-layer Suminagashi blade (middle layerof VG10 steel). The handle scales of select cocobolo wood are pre-mounted.

No. 709180 83.19 € 99.00 €

B HIRO® FOLDING KNIFE KITWith this kit from the Japanese masterblacksmith Hiro, and a bit of manualdexterity, you can build your own pocketknife. Blade of rustproof Hitachi GIN1steel, nickel silver fittings, handle scalesof glue-laminated walnut wood.

No. 719517 48.40 € 57.60 €

C »IVORY« FOLDING KNIFE KITA reliable daily companion - for self-as-sembly! Kit for a handy, light back-lockknife. The micarta handle scales with anivory appearance are already fastened tothe plates and are outstandingly suitablefor scrimshaw decoration. Blade of rust-proof 440 A tool steel, nickel silver flan-

No. 709189 29.16 € 34.70 €

D BACK LOCK FOLDING KNIFE KIT

Assemble your individual folding knife –with a little craftsman’s skill and the»Back Lock« knife kit. The kit containsall necessary components, including a No. 709184 33.53 € 39.90 €

Fixed knives

E IC CUT® OUTDOOR KNIFE KIT

Compose your own individual outdoorknife with high quality components fromIC Cut: 3.5 mm thick blade of rustproof No. 709039 50.92 € 60.60 €

F BRUSLETTO® FALKEN KNIFE KIT

With these high quality components anda small amount of work you can build your No. 709130 50.42 € 60.00 €

G KIT FOR A NORDIC STYLE KNIFEIncludes all the materials required formaking your own highly individual Nordicknife. Hardened, pre-sharpened Udde-holm No. 1770 carbon steel blade,masur birch, reindeer horn slice, brasshead plate, leather, thread, with brief assembly instructions.Blade length 93 mmOverall length 205 mmBlade thickness 2.5 mmNo. 709062 28.49 € 33.90 €

KLEINES BREVIER VOM MESSER MACHENBy Bo Bergmann. In this compact book,the master of Scandi-navian knife makingoffers an ideal intro-duction to a wonderfulhobby. However, evenexperienced knife-ma-kers will find interes-ting information ontools, materials, work-ing techniques and finishing. A documentation of different types of knives make this booka valuable guide for every knife-maker.112 pages, 46 b/w drawings and 8 colourpanels, hardcover, 130 x 205 mm.In German.No. 713163 20.56 € 22.00 €

Fittings and plates of nickel silver. Stableand attractive punched leather sheathand belt loop for storage and transport.With detailed assembly instructions.Outer edges of rustproof stainless steel.Blade length 75 mmOverall length 175 mmBlade thickness 3 mmWeight of the finished knife approx. 110 g

With detailed assembly instructions.Blade length 67 mmOverall length 170 mmBlade thickness 3 mmWeight of the finished knife approx. 120 g

ges and plates. With detailed assemblyinstructions.Blade length 55 mmOverall length 140 mmBlade thickness 2 mmWeight of the finished knife approx. 50 g

satined blade of rustproof Hitachi steel(AUS6), pre-assembled handle scales ofwaterproof glue-laminated exotic wood aswell as plates and flanges of nickel silver.With detailed assembly instructions.Blade length 85 mmOverall length 195 mmBlade thickness 3 mmWeight of the finished knife approx. 170 g

AUS6 steel, hardened and annealed, flat-ground sides, hollow-ground cuttingedge, laminated cocobolo handle scales,studs, sturdy belt-mounting leather sheath, assembly instructions.Blade length 110 mmOverall length 235 mmBlade thickness 3.5 mmWeight of the finished knife approx. 240 g

own individual hunting knife. Falken blade,walnut handle, sturdy hand protection,2.2 mm sheath leather, inlay, needle,thread, rivet, assembly instructions.Blade length 87 mmOverall length 210 mmBlade thickness 3.3 mm

A

B

C

D

E

F

G

Knives || Obsidian

218

Obsidian

THE MOTHER OF ALL BLADES

Igneous obsidian was used to make ar-rowheads and knife blades long beforehumankind discovered how to forge steelblades. The extreme sharpness of thismaterial made it essential to the ancientJapanese for bear hunting and to theAztecs as ritual knives. The knowledge

required to fracture this extremely brittlenaturally occurring material into usefulblade shapes has virtually disappeared.One enclave remains in Hokkaido, wherehigh-quality obsidian is still available insufficient quantities. We are pleased tobe able to offer original Hokkaido obsidianof this quality to ambitious knifemakers,experimental anthropologists and other

handcraft artists. The semi-translucentstones also are amazingly eye-catching,allowing them to be additionally suitablefor making jewellery and other fine objects.

To work this stone you require a stone forsplitting large chunks, a deer horn ham-mer and a deer horn tip for the fine split-ting work and leather hand protection.

We wish to point out that the invisiblestructure of the obsidian and a lack ofexperience may result in an unusableproduct in many cases. »Instructions«are provided.

A OBSIDIAN KNIFE BY SUEMORIUnikates:The Hokkaido-based knife-maker TokashiSuemori learned the archaic art of fractur-ing obsidian from the Ainu, an ancienttribe in the north of Japan. We are occasionally able to offer examples of hiswork, with each piece having a uniqueform. The price lies between about 280-450 € depending on the size and form of the knife.No. 716247 Price on request

B OBSIDIAN, BLACKMedium sized pieces, transparent black.300-700 g/stone (approx. 80-150 mm),minimum order quantity 1 kg.

Price per kgNo. 716245 18.40 € 21.90 €

C OBSIDIAN, BROWNRelatively large pieces, brown/black speck-led, 800 g to 2 kg/stone (approx. 100-200mm), minimum order quantity 1 kg.

Price per kgNo. 716246 13.53 € 16.10 €

D DEER HORN TIPFor finely splitting the obsidian.No. 820130 1.76 € 2.10 €

E HORN HAMMERFor roughly splitting the obsidian.No. 820131 11.93 € 14.20 €

A

B

C

D

E

Brief glossary of steel terms

ATS 34: A very pure, rustproof carbonsteel made in Japan that displays a very fine crystalline structure due to its high molybdenum content. (C = 1%, Cr = 13.5%,Mo = 3.5%, Mn = 0.4%, P = 0.023%, S = 0.003%)

AUS 6 M:Similarly to »Silver Paper Steel«, just slightlysofter. (Cr= 14%, C= 0,6%, Mo = 0,2%, V = 0,2%)

Blue Paper Steel (Ao Gami): Similar to WhitePaper Steel but alloyed with an additional0.4% chromium and 1.8% tungsten. This makes it somewhat tougher.

Cowry X: Stainless heavy duty steel madeusing the powder metallurgy process.(C = 3%, Cr = 20%, Mo = 1%, V = 0.3%,HRC 65-67).

Damascus steel: Named after Damascus,the ancient centre of the metalworkingtrade, this steel is well-known for its highlygrained surface. First produced in Indiaaround 300 BC. The unique structure wasoriginally created using steel segregationtechniques during cooling (to make whatwas known as Wootz steel). In modern Da-mascus steels, this structure is created byforge welding and folding steels of differentcarbon contents together.

Iron (Fe): Does not occur naturally in its pureform (other than in meteorite iron). Obtainedby smelting iron oxides (iron ore, magnetite,etc.) it was first produced in Asia approx.2600 years ago.

HSS (High Speed Steel): A type of steelwhich is heat resistant to approx. 570 °Cdue to a relatively high content of chromium,

molybdenum, tungsten and vanadium. Used in machine and turning tool blades.

Carbon steel: A non-alloyed tool steel with acarbon content of 0.2 - 1.7% which can besharpened to a very high degree due to itsfine grain structure.

Alloying: The addition of certain metals (e.g. chromium, manganese) to change the characteristics of the base metal.

SG-2: Stainless heavy duty steel made usingthe powder metallurgy process. (C = 1.3%,Cr = 15%, Mo = 3%, V = 2%, HRC 63-65).

Silver Paper Steel (Gin Gami, GIN1):Rustproof blade steel made by Hitachi. Particularly corrosion- and wear-resistantdue to its high chromium content (chromium carbides). (C = 0.9%, Cr = 16%,Mn = 0.6%, Mo = 0.4%, S = < 0.004%, P < 0.025%).

Sintered steel: Sintering allows metals whichnormally cannot be alloyed or welded togetherto be combined. The components are mixedin powdered form and then hot isostaticallypressed in a process known as Powder Metallurgy (PM). The Swedish DamasteelAB company has used this technique since1995 to produce rustproof Damascus steelwith an extremely fine martensitic structure.The steel, called RWL 34, contains 1% C,14% Cr, 4% Mo and 0.2% V. It displays excellent sharpening properties, is extremelytough and very resistant to wear, making itideal for use in the blades of outdoor knives.

SKD 11:High-alloyed Japanese tool steel, which wasoriginally developed for the use of machine

tools. Due to its high percentage of carbide it is very abrasion resistant, durable and non-corroding but not rust-proof.

Steel: A forgeable, alloyed or non-alloyediron with a carbon content (C) of between0.1% and maximally 1.7%.

Suminagashi steel: A Japanese variation ofDamascus steel that contains a carbon steelcore, in contrast to European Damascusblades.

Tamahagane: Japanese sword steel pro-duced from iron sand (Masa) smelted in acharcoal fired furnace. This process, called»Tatara«, is the earliest known method (ap-prox. 1800 years old) in which steel can beobtained directly from the raw material with -out any intermediate steps. It yields steelwith the highest possible degree of purity.

VG-10 steel: Rustproof high-class bladesteel, made in Takefu. Its high content of cobalt and carbides make it extremely durable. (C = 1.0%, Cr = 15%, Mo = 1.0%, V = 0.2%, Co = 1.5%).

White Paper Steel (Shiro Gami): Trade namefor a type of highly pure carbon steel madeby the Hitachi Company that is smelted fromiron sand (Masa) and is of particularly highquality, mainly used for making cutting tools.(C = 1.2%, S < 0.004%, P < 0.025%).

Tool steel: Alloyed or non-alloyed steel with acarbon content of at least 0.2%, a levelwhich allows the steel to be hardened.

440 C: Hardenable stainless steel originallydeveloped for making ball bearings. High re-sistance to corrosion and wear. (C = 1%, Cr= 17%, Mn = 1%, S = 0.05%, P = 0.04%).

Hardening: Heating hardenable steel toabove the transformation point (approx. 780°C for carbon steels, approx. 1050 °C forrustproof steels, depending on the alloy) andsubse-quently quenching them (in water, oilor air) results in the formation of a new, finercrystalline structure. The steel gets harder,more brittle and more sharpenable becauseof the finer structure. The hardness can betested using the Rockwell method (pressinga diamond cone into the surface of thesteel).

Annealing: After hardening, the steel mustbe annealed to avoid brittleness. In general,the steel is heated in a controlled manner(for a specific time at between 180 and 300°C) to remove the internal stresses in thestructure. In the process, the steel becomessomewhat less hard, but gets tougher andless prone to chipping.

It is important to note that the properties ex-hibited by an individual blade do not solelydepend on the chemical composition of thesteel used. The blacksmith’s skill and thenature of the hardening process employedalso play a very important role in the qualityof the outcome. Careful forging, for example,further refines and homogenises the steel’sstructure. Prolonged heating during the forg-ing, hardening or annealing process lead to carbon diffusion that diminishes the hard-ness and edge life of the blade. Impurities(e.g. P, S) have a very detrimental effect onthe blade and cause a dramatic increase inthe brittleness of the edge.

This glossary is regularely updated and can also be found on our websitewww.more-than-tools.de

Razors and accessories | 221

Scissors | 223

219

Light and convenient!

Razors and scissors

220

NEW

Sharpening pass


Sharpening service



STRUCTURE OF THE STRAIGHT RAZOR

Blade profile:

Types of hollow grind:

A: Flat (flat-ground razor)

B: ½ hollow

C: Full hollow

The first straight razor blades were wedge-

shaped, rather like kitchen knives. This is

called a flat grind. Over time, the idea of a

blade with a hollow grind developed. This

hollow grind makes the blade easier to hone

and allows an extremely fine cutting edge.

The thinner the cutting edge, the better the

shave, because the blade edge can adjust

better to the skin contours, which is why ½

hollow and other types of hollow grind devel-

oped. Another revolution was the full hollow.

This type is the most elaborate and therefore

the most expensive.

As you can see in the picture above, the

blades actually have two hollows, between

which a thin »ridge« is formed along the

middle of the blade. In the picture, this

ridge is shown disproportionately, but it can also

be detected on the razor itself by a different

reflection of the blade. The ridge increases

stability and allows an even finer cutting edge.

When ground to perfection, a razor like this

can »sing«. You can detect a full hollow with

the »nail test«: When pressed on the thumb-

nail, the cutting edge will yield already to light

pressure and then spring back fully. This

means that the blade is highly elastic at the

front and can thus easily follow the surface

structure.

Stabiliser

Another distinguishing feature of a full or

half hollow is the stabiliser where the blade

meets the tang. A full hollow usually has a

double stabiliser, which marks the transition

from the blade to the tang in steps. The sta-

biliser protects the blade from torsional ben-

ding in the transverse direction. A half hollow

only has one stabiliser. Resistance to torsional

bending is less important for half hollows

because nowadays they tend to be used for

narrow blades.

Blade widths

Blade widths are traditionally specified in in-

ches. A 3/8 razor is a smallish razor, which is

used, for example, by barbers to shave the

neck or for parts of the body that are not too

round.

Most razors are offered as 4/8, 5/8 and 6/8

inch, which are the best sizes for shaving.

7/8 and 8/8 inch require special experience,

therefore beginners should start with 4/8- or

5/8-inch razors. In principle, the size should

suit the size of the hand and the face. The

5/8- or 6/8-inch widths are the most common

sizes for beard shaving and are ideal for the

chin and cheeks.

SHARPENING AND POLISHINGThe choice is yours:

Opinions often differ when it comes to sharp-

ening - a good solution for one person may be

far from perfect for another. We would like to

give a general recommendation from our ex-

perience.

For a blade needing restoration:

A blade that needs restoring should always

be honed on a honing stone first. For this

purpose we recommend our Shapton stones.

The ceramic bond makes the stones harder

than water stones and, because of the readily

available grits of up to 16000, they are ideal

for the fine grinding of razors. For many, this

will be sharp enough, but others will want to

polish the blade further with finishing pastes.

Following use of an appropriate hone (or

hones) to restore the correct edge geometry,

we recommend successive use of bio-diamond

compounds in the following grades:

6 micron, 3 micron, 1 micron and 0.25 micron.

These steps are then followed by stropping

on a surface with chromoxide finishing paste

and then stropping of the razor on unpasted

leather.

For an out-of-the-box razor that may not yet be

completely shave-ready:

For beginners, the Thiers Issard aluminium-

oxide-based sharpening paste is sufficient to

make a blade fit for shaving. After the paste,

strop the blade without paste.

For professionals, we recommend using the

following in this order: Bio-diamond sharpe-

ning pastes 6 micron, 3 micron, 1 micron,

0.25 micron, chromoxide paste and finally,

an unpasted strop.

In addition, for regular razor care once every

2 or 3 weeks, the following sequence:

Bio-diamond paste 1 micron, bio-diamond

paste 0.25 micron, chromoxide paste and

finally, an unpasted strop.

For a razor already in regular use:

Before shaving, we recommend using either

a strop coated with Thiers-Issard finishing

paste, followed by an unpasted strop or, if

you wish, an unpasted strop by itself.

A CB

THE FINE ART OF WET SHAVING

Handle

Point Hollow ground Cutting edge

Back Double stabalizing piece Tang

Jimps

Tang

Razors and scissors || Razors and accessories

221

Razors and accessories

No. 709199 67.14 € 79.90 €

B RAZOR »LE DANDY«

No. 709014 78.15 € 93.00 €

C RAZOR »LOUP ET BÉLIER« 1 Norman cow hornNo. 709015 158.82 € 189.00 €

2 SnakewoodNo. 709016 152.94 € 182.00 €

3 Palm woodNo. 709121 152.94 € 182.00 €

D HISTORIC FRENCH RAZORMade of 100-year old steel:

No. 709122 167.23 € 199.00 €

E RAZOR SILVERWING »FRENCH NOSE«

No. 709209 247.90 € 295.00 €

G LEATHER CASE FOR RAZORHigh quality brown calf leather case withleather tongue closing. Fits all Thier Issard Razors. Ideal for travelling.No. 709159 10.84 € 12.90 €

F LEATHER ROLL-UP CASE FORSTRAIGHT RAZORS OR FOLDING KNIVESExclusive and space-saving, this roll-upcase of fine brown calf leather providessafe and compact storage for straight razors or folding knives and is convenientfor travellers to use. It is rolled and fas-tened with two leather straps and can behung on a hook using the leather loop. It will accommodate up to 7 razorsand/or folding knives. Hand-made inFrance by Thiers Issard.365 x 210 mmNo. 709154 52.94 € 63.00 €

A

B

C

2

D

E

1

3

FG

The traditional French company ThiersIssard in Auvergne has been manufactur-ing exquisite straight razors for wet shaving since 1884. The blade is madeof carbon-steel* from Sheffield (SilverSteel) which, due to its fine-grainedstructure and extreme hardness of 63HRC, can be ground very thin and thusretains the necessary sharpness for acomfortable shave. Comes with leather case.* Carbon-steel is far superior to rustproofsteel as far as sharpness is concerned.The supposed disadvantage of rust sus-ceptibility is offset by following the careinstructions.

Care instructions:After shaving, clean the knife with purewater and dry thoroughly. If the razor isnot used over a long period of time, itshould be slightly oiled ( e.g. cameliaoil, No. 705280).

These elegantly designed razors are patterned after an antique model. The slightly curved tang improves ease ofuse, fully hollow-ground, mirror-polishedblade.Blade length 70 mmOverall length 250 mmBlade width 5/8"

These razors are made using extra wideblades forged at the beginning of the19th century from the very best SheffieldCast-steel. With hand-filed, decorativeblade backs and a magnificent handlemade of striped Norman cow horn. Fullhollow. Provided in a lovely leather case.Blade length 75 mmOverall length 260 mmBlade width 6/8"

The new anniversaryrazor has a Frenchhead and beautifulram-horn handle scales which makeeach piece unique.This special edition islimited, with each razor coming in anelegant walnut-stained box engraved with a specimen number. The blade is fullyhollowed mirror-polished.Blade length 65 mmOverall length 250 mmBlade width 5/8"

A RAZOR »SUPER GNOME«Slim, unpretentious razor with a narrowsatin finished 1/2 hollowed blade, basedon a historical model manufactured ofblanks which were forged decades ago inSolingen. Delicate razors of this type arebecoming increasingly popular, alsoamong the ladies. Black handle scalesmade of high-grade plastic.Blade length 70 mmOverall length 220 mmBlade thickness 3/8''.

Black plastic handle scales. Satin polished fully hollowed blade.Blade length 70 mmOverall length 250 mmBlade width 5/8"

Razors and scissors || Razors and accessories

222

L CHROMOXIDE FINISHING PASTEAfter sharpening with extra-fine diamondgrits, e.g. 0.25, this finishing paste isused to take the »bite« out of a too ag-gressive blade, thus avoiding possible ir-ritation and/or razor-burn. Applied on thefine leather side of an additional strop,this paste will give you the smoothest edge you’ve ever experienced. Oil-basedcarrier.Content: 50 gNo. 709124 17.56 € 20.90 €

K BIO DIAMOND PASTES, 4-PIECE SETThese Bio Diamond sharpening pasteshave a more fluid, water-based carrierwith no harmful chemical additives orsolvents and are therefore particularlygentle on the skin. The fluid substance inthe handy dispenser allows easy and eco-nomical application. Normally the pasteslast for many years. The high content ofeven-sized, sieved diamond particles en-sures fast and effective abrasion. Any re-sidual paste can be easily removed. Colorcoding: yellow 6 micron, green 3 micron,red 1 micron, grey 0.25 micron.Content per tube 10 mlNo. 709125 100.00 € 119.00 €

F ENGLISH SHAVING BRUSHA fine, badger hair brush is essential forattaining the perfect shave. The rounded,uniform, dome-shaped brush head featu-res unformly colored black hairs withsplit white ends and offers an unsurpas-sed, luxurious feel during use. Made bymaster brushmakers at a renowned com-pany situated on the Isle of Man. Hand-sorted badger hair with a turned handlemade of cream-colored polyester.Head-Ø 60 mmLength 150 mmNo. 709009 52.86 € 62.90 €

G SHAVING SOAP DISH WITH LIDRustproof steel shaving soap dish withhigh-gloss polished finish. The lid pro-tects the shaving soap from dust and dirt.The easy-to-clean dish weighs only 85 g. Ø 90 mm85 gNo. 709197 18.40 € 21.90 €

E ALUM CRYSTAL SHAVING BLOCKShaving and disinfection block of purealum (a type of aluminium sulphate) forsmall wounds caused by shaving. Haemo-static, astringent and antiseptic effect.When dissolved with water on the skin,alum disinfects and closes wounds. To dothis, one lightly rubs the moistened blockover the injured spot.125 gNo. 709195 13.03 € 15.50 €

No. 709018 40.25 € 47.90 €

No. 709024 41.93 € 49.90 €

No. 709013 58.74 € 69.90 €

J THIERS ISSARD SHARPENING PASTEThe paste for regular, effortless use:

No. 709019 4.54 € 5.40 €

Please refer to the tips on sharpeningrazors in the attached user instruc-tions.

More razor accessories can be foundat www.more-than-tools.de

A JAPANESE RAZORThe archetypal razor:

No. 709023 235.29 € 280.00 €

B JAPANESE RAZOR MADE OF TAMAHAGANERazor made of Sword Steel:

No. 709026 411.76 € 490.00 €

C ALMOND SHAVING SOAPCreamy, skincare shaving soap with discrete almond scent. The warm latheropens the pores of the skin, softenswhiskers while shaving and allows theblade to glide over the skin more smooth-ly. Thus the whiskers are not torn out butshaved off cleanly, smoothly and pain-lessly.Approx. 80 gNo. 709194 10.00 € 11.90 €

D SANDALWOOD SHAVING CREAMSoft cream for the perfect shave withpleasant sandalwood aromas. In plastic container. 180 gNo. 709022 18.32 € 21.80 €

A B

C D F GE

H

2

J K

L

The knives offered here are created inthe workshop of the legendary blacksmithShigeyoshi Iwasaki, who is over 80 yearsold. He produces them together with hisstudent Ryoichi Mizuochi. The knives aremade of finest carbon-steel, forge weldedin a charcoal furnace with Rentetsu ironand polished on natural stone. Only thosepieces satisfying the stringent standardsof the master are certified with his sealon the rear side of the blade. A fascina-ting cult object for collectors and usersalike. Provided in a lovely kiri wood case. Not rustproof.

These archaic razors are made of strictlylimited Tamahagane, the original steelused by the legendary Japanese sword-smiths. Each year, only small amounts ofthis precious steel are being smelted.Each hand forged razor is unique. Theextremely sharp blade is hand polishedwith natural sharpening stones and fea-tures two layers: hard Tamahagane forthe edge and soft iron for the bladeshoulder. Delivery in a beautiful wooden

Blade length 50 mmOverall length 160 mmBlade width 21 mm

case. The blade is stamped with the sealof the master blacksmith and bears theTamahagane signature. Available in October 2010.Blade length 60 mmOverall length 170 mmBlade width 22 mm

H STROP BOXThe stylish container for storing and sharp-ening razors. Lined with leather on bothsides, twist lid.Leather surface 170 x 40 mm330 x 40 x 35 mm

I PADDLE STROPSFrench strop with different leather sides,attached to a beech paddle with woodribs. These allow the strop to adjust tothe blade, similar to a hanging strop.Sharpening paste can be applied on bothsides; the brown leather is suitable fordaily stropping.

1 Narrow in synthetic leather caseIdeal professional strop for on the go,thanks to practical storage in syntheticleather case.Leather surface 215 x 35 mm350 x 35 x 15 mm

2 WideExtra-wide version, suitable for beginners.Leather surface 250 x 75 mm410 x 75 x 20 mm

Thanks to its aluminium oxide abrasive,which is less aggressive than diamond,the Thiers Issard sharpening paste is ide-al for delaying the more complex basicsharpening (approx. every 2-3 weeks) alittle longer. The paste is used to retainthe sharpness for longer and can regular-ly be applied before each 3rd or 4thshave. Rub a thin layer of paste into thecotton side of a hanging strop or the se-cond leather side of the strop. First»sharpen« on the paste side and then fi-nish on the leather side without paste.10 g

I

1

Razors and scissors || Razors and accessories, Scissors

223

No. 709136 43.70 € 52.00 €

B HANGING STROP STARTER SET

No. 709137 50.34 € 59.90 €

C HANGING STROPS

More strops can be found in thesharpening devices chapter.

Scissors

Japanese scissors (Nigiri)Japanese Nigiri are scissors in their mostarchetypal form. Forged from a single pieceof steel, they are exceptionally light andcomfortable to hold. Pressure from thethumb and forefinger produces well-con-trolled cuts; the spring action of the thinlyforged handle causes the blades to reopenautomatically. Nigiri are suitable for all precise work with paper and fabric, opening seams, and pruning houseplants. All Nigiri come in elegant gift boxes.

D SISHU NIGIRI, HAND-FORGEDHand-forged, double-layered steel blade,extra finelyground edge, very sharp.Overall length 105 mmBlade length 45 mm20 gNo. 718105 28.49 € 33.90 €

E NAGA-HA NIGIRI, HAND-FORGEDHand-forged, double-layered steel blade,bronzed black finish, finelyground edge.Overall length 150 mmBlade length 65 mm60 gNo. 718127 23.45 € 27.90 €

F SISHU NIGIRIDouble-layered steel, bronzed black finish.Overall length 120 mmBlade length 55 mm25 gNo. 718106 19.24 € 22.90 €

G MINI NIGIRISilk cord wrapped handle, solid blade,standardground edge.Overall length 75 mmBlade length 27 mm10 gNo. 718101 5.46 € 6.50 €

Japanese Tailor's scissors

No. 718132 81.09 € 96.50 € Free handed grinding of scissors.

A B

E

F

D

G

H

StropDuring shaving, the ultra-fine edge ofthe razor bends when it meets a beardhair. This »burr« that forms on the razorblade partially straightens up with time(min. 24 hours), but stropping removesit completely. The razor strop works likea burnisher with a conventional bladethat isn't sharpened but cuts only withthe fine rised burr.

Hanging strop / paddle strop with ribsBasically, hanging strops and paddlestrops require the blade to be managedin the same way. The type of strop ismore a matter of taste. The fine ribs inthe wood of the paddle strop create anelasticity that feels similar to stroppingon a hanging strop.Both types are available in two widths. Onthe narrow version, the razor must be han-dled differently than on the wide version.

On the narrow strop, you must draw theblade in the form of an elongated X,which seems more difficult for begin-ners. Professionals, however, can stropindividual parts of the cutting edge withmuch more control on a narrow strop.The narrow width also reduces bendingin the transverse direction.On a wide strop, you can draw the bladein parallel to the edge of the strop, whichis much easier to learn for a beginner.

C

1

2

A STROP STARTER SETThe 75 mm wide strop for easy blademanagement and the Thiers Issard sharp-ening paste make up the ideal set fornewcomers to wet shaving. For refiningthe blade between sharpenings, the sharp-ening paste is applied to the rougher leather side.410 x 75 x 20 mm

This set consists of an 80 mm wide hang-ing strop that's ideal for beginners becausethe blade is easier to manage, a leathercream for leather care and a Thiers Issardsharpening paste for refining the edge onthe cotton side between sharpenings.695 x 80 x 3 mm Hanging strops are used to straighten up

razor edges, since they adjust to therounding of the blade. The supplied hookis mounted on the wall and the strop ishung on it with the attached swivellingclamp. The swivelling clamp also allowsquick switching of the two sides. Thesanded top of our strops is made of high-quality vegetable-tanned cowhide (Thick-ness 3 mm), which is exceptionally soft.If required, the rear, cotton side of thestrop can be used with so-called sharpen-ing pastes, and thus serves as a substi-tute for sharpening on a fine honingstone.Overall length 695 mmWorking length 390 mm

1 Hanging strop 40 mmA 40 mm wide strop requires a more precise stropping technique than a widerstrop. The great advantage of a narrowstrop is that the leather hardly bendsalong the narrow width. This ensures exquisite sharpness.No. 709138 32.77 € 39.00 €

2 Hanging strop 80 mmWith its 80 mm width, this strop is idealfor beginners, since they can draw the razor at a right angle along the wholewidth. No. 709139 45.38 € 54.00 €

Hand-made, lightweight tailor’s scissorsfor cutting material softly and effortless-ly. The carefully hand-forged blades, themanually sharpened facets and the preci-sion adjustment when they are assembledmake these scissors the perfect tool forthe high demands of tailoring. The cutting action can be adjusted.

H DELUXE TAILOR’S SCISSORSExclusive mirror-polished, stainless steelblades, gold-plated handles, right-handed.The blades are sharpened by hand, andpromise an extraordinarily long service life.Overall length 260 mmBlade length 115 mm275 g

Price advantagePrice advantage

Hair cutting scissors

H HAIR CUTTING SCISSORS -LINE

1 Super cut goldThe gold-coloured surface coating not only gives these scissors an attractivelook but also makes them easy-care andresistant to chemical hair care products.Asymmetric handles, knurled adjustmentscrew, rubber stopper, removable fingerrest. 2 finger rings for size adjustment.

Overall length 135 mmBlade length 55 mm47 gNo. 708189 53.70 € 63.90 €


2 Super cut



3 Double bowCompact scissors with double bow on thelower blade (for forefinger and middlefinger) for perfect cutting control.Knurled adjustment screw, rubber stop-per, finger rest. 3 finger rings for size adjustment.



Razors and scissors || Scissors

224

A PROFESSIONAL TAILOR’S SCISSORSTop-quality tailor's scissors made of finely polished high-performance Yasugi carbon-steel. Double-layered, hardenedto 65 HRC, with a brass nut.Blade length 85 / 105 mmOverall length195 mm No. 718130 32.10 € 38.20 € 240 mm No. 718131 49.33 € 58.70 €

B TAILOR’S SCISSORSDouble-layered steel.Blade length 90 / 105 mmOverall length200 mm No. 718136 24.20 € 28.80 € 240 mm No. 718135 29.66 € 35.30 €

C PINKING SHEARSFor decorative finis-hing of cloth edges.The curved notches in the blades madeof differentially hardened, chrome-platedcarbon-steel make these Japanese shearsa masterpiece of precision mechanics.Overall length 230 mmBlade length 100 mm245 gNo. 718139 41.93 € 49.90 €

All-purpose scissors

D TRADITIONAL JAPANESE HOUSEHOLD SCISSORSWonderfully lightweight (80 g) and withhigh-precision cutting, these hand-forgedscissors are outstanding in both form andfunction. Double-layered steel. Adjust-able cutting action.Overall length 185 mmBlade length 70 mm80 gNo. 718147 33.53 € 39.90 €

E FRENCH HOUSEHOLD SCISSORSAND FABRIC SCISSORSStrong, classical, multipurpose hand-made scissors for cutting fabric, paperand thin leather.Overall length 170 mmBlade length 70 mm75 gNo. 708142 25.97 € 30.90 €

F FRENCH HOUSEHOLD AND SEWING SCISSORSExtraordinarily light. Made of hard-chrome-plated carbon-steel.Overall length 140 mmBlade length 60 mm30 gNo. 708141 17.56 € 20.90 €

G TRADITIONAL CHINESE SCISSORSAll-purpose stainless steel scissors withpolished blades. The Chinese symbols forluck and longevity, a peacock and a drag-on, grace the brassbound handles.Blade length 55 / 60 / 70 mmOverall length150 mm No. 708151 8.82 € 10.50 € 175 mm No. 708152 9.83 € 11.70 € 195 mm No. 708153 10.59 € 12.60 €

TRADITIONAL CHINESE SCISSORS, 3-PIECE SETNo. 708151, 708152 and 708153.No. 708154 25.13 € 29.90 €

Price advantage

A B

C

D E

F G

H

1 2 3

High-quality, great price:Our D-Line haircutting scissors prove thatscissors that meet professional demandscan also be affordable. They offer all thefeatures you would expect from high-quality haircutting scissors at an attractive price:

- Forged blades from 420 J2* stainless steel.

- Hollow-ground backs and manually sharpened facets for a clean cut.

- Large knurled screw with 1/20 pitch for fine adjustment.

- Perfectly rounded and burr-free handleswith ergonomic bows for a good grip.

- Smooth, gentle cutting with rubber stopper.

Hardness approx. HRC 54.

Thanks to their ergonomic asymmetrichandles, these scissors are very comfort-able to hold. Adjustment screw and fin-ger rest with gold-coloured coating (TiN).Knurled adjustment screw, rubber stop-per, removable finger rest. 2 finger rings for size adjustment.

More scissors can be found atwww.more-than-tools.de

Hoes and claws | 227

Shovels, forks and rakes | 229

Garden knives| 230

One-hand garden shears | 230

Two-hand garden shears | 233

Hedge shears | 233

Branch shears | 233

Tools for bonsai trees and ornamental plants | 234

Watering cans | 234

Japanese pruning saws | 235

Folding saws | 235

Fixed blade pruning saws | 236

Telescoping pruning saws | 237

Scythes and accessories | 238

Sickles | 239

Gardening sets | 240

Gardening accessories and useful items | 240

225

The sheer pleasure of gardening.

Garden tools

226

INDISPENSABLE HELPERS FOR EVERY SEASON

Is there a nicer job than doing something

good for the plants and, at the same time,

finding relaxation for the mind and body?

Garden work is one of the last refuges where

you can still enjoy harmony with nature.

Prerequisite are tools which almost silently

and effortlessly fulfil their function.

In contrast to the garden itself, which is

subject to constant change, tools are some-

thing permanent. Their durability, their hand-

ling, and their dependability are what make

them trustworthy objects. Tools with a soul

are, as a rule, not mass-produced articles.

They come from small blacksmith workshops,

where the master blacksmith still identifies

himself with his product and manufactures

it with the same care with which it should

be used later.

Supreme sharpness and durability

Only with sharp blades can you cut plants

cleanly, and clean cuts heal quickly and pro-

tect the plants against diseases and pest in-

festation. Also for hoeing beds or mowing the

lawn you need gardening tools with a bit of a

bite.

Hand-forged hoes, sickles and garden shears

made from carbon-steel feature not only

extreme sharpness but also exceptional

hardness, breaking strength and service life.

Rediscover the pleasure of gardening with

sharp tools!

Ergonomics and aesthetics

It’s only with optimum handle lengths, blade

lengths, materials and tooth patterns that

gardening implements are a pleasure to use.

Sharpening service for cutting tools

Let our specialists, who are trained in Japan, restore your cutting tools to their original sharpness. We gently sharpen your garden tools on waterstones –naturally also with the abrasives we offer in our product range. We will return your tools to you, razor-sharp, in a few days.

To find out more about our sharpening service, please call: +49 (0)991-9109-910 or +49 (0)1805-9109-910*. *(14 cents/min. from German landlines / calls from mobiles may cost more).

We only select garden tools that guarantee

perfect handling. And we also put all our

products through their paces with heavy-duty

testing before we offer them to you.

Low maintenance

Tools made of high-quality steels can be

quickly and easily re-sharpened.

Knives, axes, hoes and shears can be effort-

lessly returned to top condition using a Japa-

nese waterstone or a diamond sharpener from

DMT. We show you how it works (see Tip:

sharpening).

Durable and reliable

The best tools are made to last – they should

serve you for life.

Our most important criteria when choosing

our garden tools are the quality of the

materials and how they are made. The blades

of Japanese sickles are today still forge-

welded in a process developed by Samurai

swordsmiths in the 7th century. This results

in excellent hardness, breaking strength and

lightness. Put your trust in our 30 years’

experience of Japanese garden tools! We

also check our products regularly

to make sure they contain no harmful sub-

stances, especially in synthetic tool handles.

TIP: SHARPENING OF GARDEN TOOLS:

As basic equipment, we recommend a

DMT diamond combination sharpener

(No. 705391) with fine and coarse grains,

which has proven itself in mobile use. It is

equally suited for use with knives, axes, hoes,

and shears. Lay the tool on a solid support,

moisten the blade with water, and guide the

sharpener with uniform strokes - while main-

taining the specified bevel angle - transverse-

ly to the cutting edge. Sharpen firstly with

the coarse grain and then with the fine grain,

until you no longer feel any burrs on the

cutting edge.

Shears for paring branches and hedges

Take the shears apart and sharpen only the

blade facet on the bevelled side (front), and

not on the concave backside! Never sharpen

the high-quality hardened tool on a bench

grinder, as the hardness and life are adverse-

ly affected by overheating! If you wish, you

can call upon our professional sharpening

service (page 2).

KEY TO PICTOGRAMS

Fruit tree pruning

Slightly set saws offer smoothest

surfaces which minimises the risk

of fungal or bacterial diseases.

General pruning

These saws allow quick cuts to the

disadvantage of less smoother

surfaces through a medium wide setting.

Forestry work

Robust saws which thanks to wide

setting are suited best for forestry

work.

Garden tools || Hoes and claws

227

Hand-forged gardening tools

It only takes a glance at a traditionally arranged Japanese garden to understandthat such detailed precision requires extremely sharp gardening tools. Mostsickles and soil working tools presentedhere are manufactured in selected masterworkshops, hand-forged from carbon-steel using traditional techniques. They can be sharpened on waterstones.Even though carbon-steel is not rust free,sharpest edges are possible while sharp-ening is done with ease. We recommendstoring the gardening tools in a dry place, and oiling them slightly if they are unusedfor an extended period (e.g. with Japaneserust-protection oil, No. 711541). For sharpening, we recommend Japanesewaterstones, ceramic stones and DMT®

diamond stones. More care and expenseis needed when using hand-forged toolsbut the joy created while working withthem is every bit worth the effort.

Hoes and claws

A GARDENING HOESFor delicate, precise soil working. Japanese white oak handles.

1 Light weed hoe, stainless-steelLow-maintenance:Weighing just over one kilogram, thishandy hoe with a slightly concaved, tape-red blade is particularly light and there-fore recommended for lady gardeners. The narrow blade enables precise workaround existing plants, a particular ad-vantage when working in densely plantedbeds. Stainless steel.Blade length 150 mmBlade width 70 mmOverall length 120 cm1050 gNo. 717934 52.86 € 62.90 €

2 3-pronged hoe, stainless-steelMulti-purpose stainless steel hoe withthree 180 mm hardened prongs, forbreaking up soil, exposing roots and ef-fective removal of weeds and plant residue.Overall length 120 cm1350 gNo. 717932 53.11 € 63.20 €

B EDGING KNIFEHeavy forged blade with hardened cutting edge, ideal for cutting off lawn edges. Hardened carbon-steel.Blade length 260 mmOverall length 160 cmApprox. 2150 gNo. 718154 58.74 € 69.90 €

3 Two-handed hoe, carbon-steelPowerful hoe for digging, loosening soil and planting.Blade length 200 mmOverall length 120 cm1850 gNo. 717921 50.34 € 59.90 €

3 Prong hoeWith wide hoe and prongs.Blade length 235 mmOverall length 405 mmApprox. 550 gNo. 717903 18.40 € 21.90 €

2 Double hoeWith hoe and pick.Blade length 255 mmOverall length 405 mmApprox. 550 gNo. 717904 18.91 € 22.50 €

1 Planting hoeTapered blade.Blade length 135 mmOverall length 405 mmApprox. 450 gNo. 717902 15.46 € 18.40 €

B

32

1

2

3

1

A

C ONE-HANDED HOESFor loosening and arranging soil aroundplants. Springhammer forged from high-quality carbon-steel, hardened cuttingedges. Tapered blade to improve strengthand balance. Japanese white oak handle.

C

Garden tools || Hoes and claws

228

A TRENCHING HOESFor working large areas, such as creatingbeds, loosening soil and weeding.

1 Japanese weeding hoe

No. 718162 39.24 € 46.70 €

2 Trenching hoeWith a saddle-shaped blade, for drawingfurrows and making piles. Handle madeof ramin.Blade length 230 mmOverall length 145 cmApprox. 1000 gNo. 717906 40.25 € 47.90 €

3 Sickle hoeFor weeding and loosening the soil. Thesharp, slightly drop-point blade cuts eventhrough thick roots. Double-layered steelblade, pasania wood handle.Blade width 210 mmOverall length 120 cm970 gNo. 718155 41.93 € 49.90 €

4 Weeding hoeCombination of a sharp sickle blade anda seven-tine rake for weeding large areas.Menpisang handle.Blade width 240 mmOverall length 150 cmApprox. 1000 gNo. 717922 41.93 € 49.90 €

5 One-handed trenching hoeLightweight hoe for careful work in densley grown beds. Double-layered blade.Pasania handle.Blade length 140 mmOverall length 400 mmApprox. 215 gNo. 717905 16.72 € 19.90 €

6 Hand weederFor removing weeds from densley grownareas. Double-layered blade. Birch handle.Blade width 80 mmOverall length 380 mm150 gNo. 717908 11.68 € 13.90 €

For loosening soil for better aeration andnutrient absorbing and removing deeply-rooted weeds.

B GARDENING CLAWS

1 Cat’s paw claw

No. 717909 22.27 € 26.50 €

2 Single-prong clawSharp forged prongs. Ergonomically-shaped magnolia handle.Blade length 75 mmOverall length 210 mm120 gNo. 717910 12.52 € 14.90 €

3 3-prong clawForged prongs. Ergonomic magnolia handle.Blade length 75 mmOverall length 210 mm160 gNo. 717911 14.71 € 17.50 €

4 Long-prong rake

No. 717914 12.44 € 14.80 €

A

B

1

1

2

3

5

6

2 3 4

4

Light, hand-forged hoe with a good balance and a sharp two-layer blade. The tang is secured irremovably in a forged ring on the untreated tough Japanese white oak shaft.Blade length 180 mmOverall length 140 cm750 g

Ideal for digging up and removing deeproots. Forged hook mounted in an ironsleeve. Japanese white oak handle withknob.Blade length 95 mmOverall length 380 mm230 g

Deep-reaching, strong triple prongs for loosening soil and exposing roots. Japanese white oak handle.Blade length 140 mmOverall length 350 mm320 g

Garden tools || Shovels, forks and rakes

229

Shovels, forks and rakes

F GARDENER’S SPADEThrough its extra long socket which isdouble riveted into the handle this spadeis made for digging and turning over soil as well as for in depth loosening of ground. An edge tread protects your shoes from damage. A special hardenedblade allows for better spring and at thesame time decent hardness. The shaftmade from high quality ash is bent in the lower part for ergonomic reasons.Head 285 x 185 mmOverall length 1150 mm2150 gNo. 717944 43.61 € 51.90 €

G ROSE BED FORK

No. 717939 31.85 € 37.90 €

A JAPANESE STAINLESS STEEL GARDEN TOOLSThese elegant stainless steel garden toolsare made exclusively for our customers inJapanese master workshops. They arecompletely made of rustproof stainless-steel and very easy to look after. Thanksto the polished surface, dirt and soil doesnot cling to the tools. The shovels andforks are hardened and therefore ex-tremely wear-resistant. The head, shaftand handle are precisely welded together,hand-ground and polished. The broad YDhandles guarantee that they will be comfortable to hold.

The special bonus:With their tear-proof, textile transportcase, these shovels are ideal for mobileuse. The head case is secured to the toolshaft with a Velcro fastener.

Forged stainless steel spade with pointedhead for breaking and digging work. Including case.Head 190 x 250 mmOverall length 950 mm1500 gNo. 717937 83.19 € 99.00 €

2 Garden forkFour pronged fork for aerating, looseningand breaking up the soil. Including case.Prongs 250 mmOverall length 940 mm1850 gNo. 717938 85.71 € 102.00 €

I ADJUSTABLE LEAF-RAKEThis tough and at the same time light leaf rake can be changed in width from30 to 50 cm, which makes it possible togather yet the smallest leaves and grass.Even pebbles cannot stop this rake. A thump nut on the back of the rake allowsfor easy adjustment. The two outwardpins on each side of the rake are widerthan the others which give more effi-ciency, for example when raking moss.All metal parts are galvanised for rustprotection and to provide a non-stick surface against soil and dirt. The rake is delivered without handle.22 pinsOverall length 440 mm680 gNo. 717942 16.72 € 19.90 €

H TOOL HANDLEA tool handle made of untreated pinerests well in the hand and is low inweight. Fits for No. 717942.Shipping is only possible within Germany.Diameter 28 mmOverall length 1500 mmNo. 717965 8.32 € 9.90 €

Durable all-steel trowels for digging smallplanting holes and repotting houseplants. Narrow, lance-shaped blade withdepth indicator.

1 Slender planting trowelHead 150 x 60 mmOverall length 280 mm170 gNo. 717925 7.48 € 8.90 €

2 Wide planting trowelHead 150 x 75 mmOverall length 280 mm180 gNo. 717940 7.98 € 9.50 €

D JAPANESE PLANTING TROWELLightweight compact professional handspade with a thin, yet robust blade.Blade length 150 mmOverall length 280 mm170 gNo. 717923 7.48 € 8.90 €

Handy aid for transplanting young plants,distributing seeds and soil refilling. Setwith three conical scoops with differentdiameters. Our tip: can also be usedaround the house and in the kitchen!Overall length 170 mmNo. 717926 10.84 € 12.90 €

E JAPANESE PLANTING CONEPlanting cone with a practi-cal knob handle and stain-less steel tip. Plastic bodywith scale, zinc-plated steel core.Overall length 210 mm280 gNo. 717924 8.32 € 9.90 €

A

F G H

I

1 2

D

E

B

2

1

C

1 Pointed blade spade

B PLANTING TROWEL STAINLESS STEEL

C FLOWER SCOOP SET STAINLESS STEEL

This two pronged rose fork is used forplanting roses and aerating rose rootswith ease. This is especially important asaeration encourages root growth. In orderfor them to be able to free minerals it isessential that the soil bacteria have suffi-cient oxygen. Even weak roses will reco-ver. The heavy-duty steel head is die-forged, the handle is made of solid ash.Prongs length 260 mmProngs width 15 mmProng spacing 40 mmOverall length 1120 mm1150 g

Garden tools || Garden knives, One-hand garden shears

230

Garden knives

A NURSERY GRAFTING KNIFEClassic garden knife for plant cuttingsand slim wood shoots. The sickle-shapedblade allows small branches to be pres-sed into the cutting edge. This knife isalso perfectly suited for dressing cuts after tree pruning.Blade length 60 mmOverall length 180 mm100 gNo. 718108 33.53 € 39.90 €

B JAPANESE GARDEN KNIFEPowerful garden knife with a curved carbon-steel grafting blade and a largehandle made of untreated bubinga wood.With hanging eyelet.Blade length 75mmOverall length 195mm120 gNo. 709169 10.84 € 12.90 €

C GARDENING KNIFEReplaceable blade:

No. 709311 8.32 € 9.90 €Repl. blade No. 709313 4.12 € 4.90 €

E VICTORINOX® GRAFTING KNIFEVersatile Swiss-made grafting knife withstainless steel blades. The straight bladewith curved tip is particularly suitable for grafting fruit trees, while the curved blade is used to prune trees and shrubs.Brass bark lifter and lining. Textured polyamide handle scales.Blade length 55 mmOverall length 190 mm85 gNo. 709150 24.29 € 28.90 €

G TINA® GRAFTING KNIFEBeautifully shaped grafting knife withbark lifter on the back of the blade. Thenarrow point of the blade makes it idealfor rose grafting. Tina®, a company fromthe south of Germany, has been makinggarden knives for more than 150 years.This grafting knife will captivate you withits polished walnut handle scales andhand-forged blade of carbon-steel.Blade length 45 mmOverall length 160 mm50 gNo. 709164 46.97 € 55.90 €

F GRAFTING KNIFE WITH FOLDING BARK LIFTERPrecise grafting guaranteed:The special blade form makes this knifeideal for vine grafting. The folding barklifter is made of antibacterial brass. Carbon-steel blade. Pastic handle scales.Blade length 65 mmOverall length 170 mm85 gNo. 709310 16.72 € 19.90 €

H JAPANESE PLANTING KNIFE

No. 718157 18.24 € 21.70 €

D JAPANESE PLANTING KNIFEWITH SCALEFor digging out plantsand digging preciseplanting holes. The shovel-shapedstainless-steel bladehas a 15 cm scale andis ground on both sides.One side is serrated.Non-slip plastic han-dle with an oblong hole for hanging. Plastic sheath.Blade length 190 mmOverall length330 mm220 gNo. 718109 20.08 € 23.90 €

One-hand garden shears

All pruning shears are delivered with a sharpening pass for two free sharpenings (see page 2).

J ELEGANT BRANCH SHEARS WITH RATTAN WRAPPINGThis branch shears are the precious product of a cooperation of traditional art of forging and craftwork.The rattan wrapping of the handles provide a comfortable feeling. The solidblade made of carbon-steel (SK5) is particularly suitable for cutting brancheswithout damaging the plants because ofthe extreme sharpness of the blades. The spring is located inside the shears to protect it from loss and dirt. Adjustablefitting is provided by a screw. The shearscome in a leather sheath and in an elegant gift box.Max. branch-Ø 15-20 mmOverall length 200 mm235 gNo. 718183 100.76 € 119.90 €

A

FE G

H

B C

D

I J

Japanese Pruning Shears

Japanese pruning shears combine theknowledge of a gardening and forgingculture that is continually developing.They are extremely sharp and wear-resis-tant. For premium-class pruning shears,only the best-quality steels are used. In small forges, true masterpieces arecreated completely by hand from high-purity carbon-steel. The forged surfacesand the form of the handles are testa-ment to the master's skills. The result ispruning shears with a long life that makegardening a lasting pleasure. Their sharp-ness allows you to cut plants gently withminimal effort. Cleanly cut plant fibresheal more quickly and protect the plantfrom infections. This enhances plantgrowth and vitalises the plants.

I PREMIUM CLASSGARDENING SHEARSWith his top class gardening shears, master blacksmith Hidehisa pays tributeto the beauty of nature. He dedicates him-self to creating finely dimensioned master-pieces which are light in weight and aes-thetically pleasing. Made from YCS3-steel,all joints are polished and adjusted byhand. The handles are faced with oiledwalnut wood, making these cutting tools ajoy both to behold and to hold. Due totheir extreme sharpness, they cut almosteffortlessly while doing no harm to theplants. Comes with leather blade sheath.

1 Pruning shearsFor trimming fruit trees, hedges and decorative wood.Max. branch-Ø 15-20 mmOverall length 200 mmApprox. 200 gNo. 707489 105.80 € 125.90 €

2 Rose and harvesting shearsFor pruning rose trees and harvestingfruit, grapes and flowers.Cutting length 55 mmOverall length 200 mmApprox. 165 gNo. 707490 88.15 € 104.90 €

1 2

A small version of this branch shearcan be found at our webshop, www.more-than-tools.de

For especially clean andgentle shoot cutting. Robust plastic handle with replaceable tool-steel blade with holding edge.Blade length 65 mmOverall length 170 mm50 g

With its pointed formwith a hollow rear, theJapanese garden knifeis suitable for bothplanting and for expo-sing and moving pot-ted and outdoorplants. The toothedblade serves to cutroots and branches.Hardwood handle,sheath with belt loop,hardened stainlesssteel, rust-proof, dirt-resistant polishedsurface.Blade length 185 mmOverall length 320 mm225 g

Garden tools || One-hand garden shears

231

C BRANCH SHEARS WITH LEATHERWRAPPINGSturdy, forged shears (C-58-steel) makefor effortless cutting through branchesand twigs. Smooth leather is rusticallystrung around the curved handles, contoured to fit the heel of the hand. The shears therefore lie comfortably inthe hand. They are easy to clean after finishing work, as the cutting edges arepolished so that dirt can hardly cling tothem. The leather wrapping can be easilyreplaced, making these shears acompanion for life.Max. branch-Ø 15-20 mmOverall length 200 mm280 gNo. 718133 63.28 € 75.30 €

F REPLACEMENT LEATHER WRAPPINGFOR BRANCH SHEARS, REDFits No. 718133.No. 708921 11.68 € 13.90 €

B TREE AND VINE SHEARSShears with extremely sharp cutting edges, ideal for cutting fruit trees, rose bushes and vines. Finely polished bladeswith outstanding durability, ergonomicallyforged handles, double-layered blade.Max. branch-Ø 15-20 mmOverall length 200 mmApprox. 250 gNo. 718115 58.74 € 69.90 €Leather Case No. 718118 12.52 € 14.90 €

E GIFT SET PRUNING SHEARS ANDLEATHER CASEThe ultimate tool for keen gardeners – a very valuable gift set: a pair of extrastrong pruning and garden shears (No. 718115) with leather case (No. 718118) in a very attractive gift box.No. 718186 71.34 € 84.90 €

Price advantage

D ERGONOMIC PRUNING SHEARS

Leather Case No. 718118 12.52 € 14.90 €

Thanks to their ergonomically formed, ex-tra-wide handles, these garden shears arecomfortable to hold, even during exten-ded use. Forged of extra-hard White Pa-per Steel, they are ideal for pruning fruittrees, hedges and bushes.Max. branch-Ø 15-20 mmOverall length 200mm230gNo. 707487 57.06 € 67.90 €Leather Case No. 718118 12.52 € 14.90 €

L PRUNING AND HARVEST SHEARSWITH LEATHER SHEATH

No. 718191 25.13 € 29.90 €

A STAINLESS STEEL PRUNING SHEARSEasy to care for:Master craftsman Nakajima makes theseexceptional quality pruning shears fromsolid rust-proof stainless-steel. The stur-dy, high-gloss polished blades with case-hardened blades cut twigs and thin bran-ches effortlessly without damaging theplants. The structured grips are non-slipand comfortable to hold, and warm to body temperature within seconds.Max. branch-Ø 15-20 mmOverall length 200 mmApprox. 260 gNo. 718172 88.99 € 105.90 €

G LEATHER CASESaddler quality, with belt loop.Fits No. 718115, 718172, 718173,718133, 718169, 707487.No. 718118 12.52 € 14.90 €

H KIJO PRUNING SHEARSFeather-light shears with non-slip coated,easy to hold metal handles.Max. branch-Ø 15-20 mmOverall length 200 mm205 gNo. 718169 13.36 € 15.90 €Leather Case No. 718118 12.52 € 14.90 €

A CB

E

F

D

H

G

K BOXWOOD SHEARSFor pruning bushes and decorative plantsthere simply is no better tool than theHakari Hasami. Forged from a single piece of steel, with mirror-polished flanks.The easy action of these shears makespruning with them truly pleasurable. Hollow-ground, spring-return blades, adjustable. Handle with hand guard.Cutting length 120 mmOverall length 260 mm250 gNo. 718166 61.26 € 72.90 €

K

I ROSE SHEARSThe slender blade is particularly suitablefor cutting roses and grapes, removingflowers and precision trimming. The fitting can be adjusted.Cutting length 60 mmOverall length 200 mmApprox. 180 gNo. 718098 46.13 € 54.90 €

IJ TRIMMING SHEARSThese trimming shears are exactly rightwhen it comes to harvesting fruits orthinning out your shrubs. The slender, ta-pered shape of the forged cutting edgewill allow you to access even stems in theback or fruits hidden behind leaves. Thenon-slip, roughened surface lets thehandles lie well in the hand and thesafety latch can be easily locked. Theslightly curved contour of the polishedblade, made from carbon-steel, results ina drawing cut that leaves an extraordi-narily clean cut surface.Cutting length 75 mmOverall length 210 mm220 gNo. 718134 54.62 € 65.00 €

J

Set consisting of ergonomic pruningshears and leather case atwww.more-than-tools.de

A two-piece set consisting of the Kijopruning shears and a DMT diamond shar-pener available at www.more-than-tools.de

L

A powerful tool for ambitious gardeners.They feature a visual, colored handlewith a soft cushion to ensure superiorhandling. To facilitate work a spring be-tween the handles causes the jaws toopen again after closing. The replaceableblades are made of carbon-steel, take afine edge and stay sharp for a very longtime. Spare blades and springs are available.Max. branch-Ø 15-20 mmOverall length 210 mm205 g

Leather Case No. 718118 12.52 € 14.90 €

Garden tools || One-hand garden shears

232

E BARNEL®

PRUNING SHEARSBarnel®, a globallyrenowned manu-facturer based in theUS, has been making superlative gardentools since the 1970s.All Barnel® shearshave a patented centreoiler, by which oil is applied directly to theblades. The oiler can bequickly refilled with anoil can ( e.g. 713800).Each model has a two-position lock which letsyou change the prunerto a smaller cutting capacity, thus reducing effort, and secures theshears when not in use.Spare parts available.

1 Pruning shearsRobust lightweight pruning shears withsoft-coated handles for a non-slip grip.Carbon-steel blades. Drop-forged alumi-nium handles and body. Oiler, slidinglock.Max. branch-Ø 15-20 mmOverall length 210 mm230 gNo. 718225 40.25 € 47.90 €

2 Pruning shears with revolving handleLight yet robust pruner with soft-coatedhandle for a good grip. The revolvinghandle design prevents rubbing on thepalm, which avoids blisters and allowscomfortable continuous use. Carbon-steelblades. Drop-forged aluminium handlesand body. Oiler, sliding lock.Max. branch-Ø 15-20 mmOverall length 210 mm280 gNo. 718226 45.29 € 53.90 €

3 Mini prunerSmall pruner for light gardening. Perfectgrip also in small and slim hands. Cold-forged Japanese sword-steel blades withhard chrome finish. Pressure injectiondie cast body. Oiler, sliding lock.Max. branch-Ø 15 mmOverall length 175 mm170 gNo. 718224 31.01 € 36.90 €

More garden shears at www.more-than-tools.de

C SHEEP SHEARSThese traditional sheep shears are an iconof classic tool design. Shears of this design have been used for thousands ofyears in Europe as well as China, wherethese are still made by hand today. Theirwonderfully sharp blades are not onlyuseful for cutting hair, but also for grass,flowers and other light-duty applications.Cutting length 165 mmOverall length 320 mmapprox. 340 gNo. 708150 18.07 € 21.50 €

D SMALL GARDENING SHEARSErgonomically sophisti-cated, featherweightshears for harvestingfruit or vegetables andfor caring for pottedplants.Cutting length 30 mmOverall length 100 mm29 gNo. 718148 8.32 € 9.90 €

E

C

4

D

1

2 3

4 Trimming ShearsSmall trimming shears with slim tip forgentle cutting of low stems. Cold-forgedJapanese sword-steel blades with hardchrome finish. Pressure injection die castbody. Oiler, sliding lock.Cutting length 65 mmOverall length 200 mm160 gNo. 718227 28.49 € 33.90 €

A

1 2

A ARNO® FRENCH GARDEN SHEARSErgonomic design and sophisticatedfunction - the professional garden shearsmade by the traditional French companyArno have embodied these characteristicssince 1927. French viticulturists andfruit growers swear by the shears, whichsave energy and protect plants when har-vesting fruit and grapes and growingflowers.

1 Arno® olivewood pruning shearsStrong shears primarily for pruning fruittrees. The olivewood handles are not onlycomfortable, the fine-pores and high oilcontent of the wood actually lower thechance of developing blisters during useas well. Drop-forged, selectively hardenedcarbon-steel with hardened blade inserts.Hardness ca. 58 RC. Leather sheath withbelt loop.Max. branch-Ø 15-20 mmOverall length 200 mm295 gNo. 707480 56.72 € 67.50 €

2 Arno® small leather-handled pruning shearsThis shapely pair of shears is perfect forsmall tasks and small hands. Its light-weight and comfortable leather-linedhandles keep your hands from tiring evenafter long hours of use. Drop-forged, selectively hardened stainless-steel blades with a naturally forged surfacetexture (not polish ground). Leather sheath with belt loop and snap closure.Max. branch-Ø 10 mmOverall length 185 mm175 gNo. 707481 37.39 € 44.50 €

B PRUNING SHEARS FROM SOLINGENFor over 100 years, pruning shears havebeen manufactured in the German»blade city« of Solingen from high-qualitycarbon-steel in a simple, robust design.

2 Pruning shears with plastic-coatedhandlesPractical pruning shears with PVC-coatedhandles and a double-bevel cutting headwhich makes it ideal for cutting trees andbushes. The screw for adjusting the blades is secured by a guide plate.Strong metal hinge fastener.Max. branch-Ø 15-20 mmOverall length 210 mm330 gNo. 718230 27.65 € 32.90 €

1 All-steel pruning shearsThis solid pruner has a double-bevel cut-ting head and a robust brass spring forpowerful cuts. The screw for adjustingthe blades is secured by a guide plate.Solid metal hinge fastener. Comes in awooden box.Max. branch-Ø 15-20 mmOverall length 230 mm370 gNo. 718231 56.22 € 66.90 €

1 2

B

A

B

C

D

A: Ball bearing valveB: Oil reservoirC: Oil release channelsD: Spring

Tool handles without toxins (all plastichandles are regulary tested).

Garden tools || Two-hand garden shears

233

A B

Two-hand garden shears

Hedge shears

B JAPANESE BOXWOOD SHEARSParticularly light and elegant shears fortrimming boxwood hedges and ornamen-tal pruning. The blades are polished andexposed at the rear, which reduces fricti-on and increases cutting power. The cut-ting action can be adjusted with a crownnut. Fence with rubber buffer, ash handles.Cutting length 190 mmOverall length 725 mm760 gNo. 718171 81.68 € 97.20 €

A JAPANESE HEDGE SHEARS WITH BRANCH CUTTERYou surely know the following situation:When trimming hedges, a thick branch may stopand force you to use asaw. This change of toolsis a thing of the past withour new Japanese Dokanhedge shears. A recess in the back partof the blade fits branches up to 15 mmthickness and cuts them effortlessly andwithout unnecessary loss of time. The blades are forged from high gradeSK5 steel, the handles are made from Japanese white oak.Cutting length 180 mmOverall length 680 mm890 gNo. 718180 62.94 € 74.90 €

C LEATHER HEDGE SHEARS CASE

No. 718160 19.24 € 22.90 €

D BARNEL® TWO-HANDED PRUNINGSHEARS WITH OILERPowerful performance:The jaws of these extra light loppers aredrop forged and therefore have a very fineand uniform metal structure. An oilermakes it easy to apply oil to the cuttingedges. Together with a special hardenedbolt this cutting mechanism is almost in-destructible and cuts branches up to 35 mmwith ease. Two light handles which aretorsion-resistant through an oval shapedchamber system, are made of high qualityaluminium. A dampener minimises theshock load after the cutting and a juicerim at the anvil prevents the blades fromsticking together. The hand rest on thehandle is covered with high quality, easyto clean rubber which offers a good grip.The blade, anvil, bolt and the handlescan be ordered separately and are replaced easily.Max. branch-Ø 35 mmOverall length 800 mm1270 gNo. 707492 67.14 € 79.90 €

E TELESCOPIC RATCHET LOPPERWith its ratchet mechanism, this lopperallows you to cut branches of up to Ø 45mm with only a third of the strength younormally require. With each cut (5 rat-chets), the transmission ratio changes,always ensuring the best possible lever-age from each stroke without having toreapply the tool. The telescopic handlescan be locked securely in six positionsand, thanks to their length of 490 – 830 mm, allow you to conveniently cuttrees without a ladder. Coated blade forsmooth cutting and easy cleaning. Plastic-coated aluminium handles.Max. branch-Ø 45 mmOverall length 660 mm1580 gNo. 707475 29.33 € 34.90 €

F JAPANESE BRANCH AND ROOT SHEARS

No. 707479 47.82 € 56.90 €

G TELESCOPING SHEARS NISHIGAKI®

Combined telescopingsaw and shears for pru-ning and harvestingfruit trees. Steplessly extendable up to a length of 3 m. Anodised aluminium telescoping rod, high-strength carbon-steel blades.Max. branch-Ø 15 mmOverall length 1.8 - 3 mApprox. 1.3 kgNo. 712705 87.39 € 104.00 €Repl. blade No. 712706 17.48 € 20.80 €

G

C

Branch shears

F

D

E

Saddler quality. Fits no. 718121, 718122 and 718171.

Hitachi steel for cutting branches androots (up to 25 mm Ø). Japanese whiteoak handles.Max. branch-Ø 25 mmOverall length 600 mm950 g

Garden tools || Tools for bonsai trees and ornamental plants, Watering cans

234

Tools for bonsai trees and ornamental plants

A BONSAI SHEARSClassic:For caring for bonsai trees and houseplants. A sample of this tool was addedto the collection of the Museum of Modern Art (MOMA) in New York. Two-layer blade, adjustable fitting.Cutting length 50 mmOverall length 180 mm220 gNo. 718111 41.01 € 48.80 €

C SMALL BONSAI SHEARSMiniature gardening shears for precisepruning of house plants.Cutting length 40 mmOverall length 120 mm70 gNo. 718112 22.10 € 26.30 €

B TRADITIONAL CHINESE SCISSORS

Overall length150 mm No. 708151 8.82 € 10.50 €175 mm No. 708152 9.83 € 11.70 €195 mm No. 708153 10.59 € 12.60 €

No. 708154 25.13 € 29.90 €

Price advantage

E 8-PIECE BONSAI TOOL SETProfessional Japanese tools for any workrequired for growing and caring for bon-sai trees. Includes budding and pruningshears, leaf tweezers with trowel, root,concave and wire pliers, brush, shovelclaw. With case, 250 x 220 mmNo. 707900 146.97 € 174.90 €

D CONCAVE BRANCH CUTTERSPliers for pruning branches and budscleanly. With angled cutting edge forflush cuts right at the trunk.Cutting length 22 mmOverall length 205 mm185 gNo. 717916 33.53 € 39.90 €

F INDOOR GARDENING SET, 3-PIECETrowel, pick and rake. Chrome-platedsteel.Overall length 210-260 mmNo. 717915 9.16 € 10.90 €

Watering cans

G INDOOR WATERING CAN, 0.45 LITRE

No. 718918 50.34 € 59.90 €

H LONG-SPOUT WATERING CAN, 4 LITRES

No. 718921 91.60 € 109.00 €

Colour1 Green No. 718982 67.14 € 79.90 € 2 Red No. 718983 67.14 € 79.90 €

ColourRed No. 718984 41.93 € 49.90 €

A B

C

E

D F

H

G

I

1

2

3

All-purpose stainless steel scissors withpolished blades. The Chinese symbols forluck and longevity, a peacock and a drag-on, grace the brassbound handles.Blade length 55 / 60 / 70 mm

TRADITIONAL CHINESE SCISSORS, 3-PIECE SETNo. 708151, 708152 and 708153 in a set.

The perfect design of this elegant copperwatering can makes day-to-day plant carea pleasure, and transforms this everydayobject into an unusual ornament. Thesurface is patinised and coated.Overall length 370 mm0.45 litre

The slim, extra-long spout of this master-fully manufactured, hand-soldered water-ing can makes watering potted plantsand bonsai trees accurately real easy. A sieve in the filling opening prevents theultrafine pouring nozzles from becomingblocked. Brass container with removablesprinkler head.Overall length 800 mm4 litres

I HAWS WATERING CANSHaws world-renowned metal wateringcans have been hand-made in Englandsince 1886. The optimally balancedmodels are not only pleasing to the eyebut also delight every gardener with theirfunctionality. High-quality brass roses fordifferent uses complete these wateringcans and make watering a pleasure.

Heritage watering can 8.8 litresThe watering can classic, which holds asmuch as 8.8 litres, embodies traditionalEnglish style with its lattice weave stylingto the body. The steeper slant to the rosemakes it the ideal can for general water-ing purposes including seedlings. Whennot in use, the brass rose can be securedin a parking point without dripping. Thetwo hardwood handles provide a comfort-able grip, while the domed lid preventsspillage when watering. Galvanised andwith a powder paint coating, the wateringcans are permanently resistant to rust.Overall length 700 mm8.8 litres

3 Slimcan watering can 5 litresThanks to its oval shape (held close tothe body) and lower capacity, this modelis ideal for longer distances and high-grown sensitive blossoms.The oval brassrose, which faces upwards and sits drip-tight on the soldered-in neck, sprays thewater fine as rain and is therefore suit-able even for watering seeds or blossoms.The practical C-shaped flanged handle isextremely robust and can be held withboth hands. And the patented curvedshape ensures an even spray. Galvanisedand with a powder paint coating, the wa-tering cans are permanently resistant torust.Overall length 650 mm5 litres

For other designs and colours seewww.more-than-tools.de

Garden tools || Japanese pruning saws

235

Japanese pruning saws

For environmentally-friendly trimming of trees:Professional Japanese pruning saws helpto maintain and care for lumber and or-namental trees. Trees with cleanly cut offbranches, such as those cut with a sharpJapanese saw, are less susceptible tofungal or bacterial diseases. In contrastto the widely available average qualitylow-cost products, all our pruning sawsare manufactured in Japanese masterworkshops. The teeth are razor-sharp and the blade surfaces are hard chrome-plated and therefore corrosion-free. The tips are hardened to maximise thesaw’s durability and resistance to breakage.Replacement blades will be available formany years to come.

Folding saws

A SILKY® POCKET BOY 1 Pocket Boy 130 - coarseBlade length 130 mmOverall length 290 mmBlade thickness 0.9 mmNo. 712774 26.81 € 31.90 €Repl. blade No. 712775 15.88 € 18.90 €

2 Pocket Boy 170 - coarseBlade length 170 mmOverall length 370 mmBlade thickness 1.0 mmNo. 712776 29.33 € 34.90 €Repl. blade No. 712777 17.56 € 20.90 €

D ORIKOMI 250 - COARSEFor general pruning and outdoor use:Optimal cutting performance, even diago-nally to the grain, is guaranteed by thisfolding saw with sturdy aluminium con-struction and a non-slip elastomer grip.The trapezoidal toothing has additionalclearing teeth added at a ratio of 1:7. A tooth spacing, which becomes finer towards the blade enables a progressivecutting force. The hard-chrome-plated,corrosion-free blade, guarantees a longlifetime.

No. 712754 30.84 € 36.70 €Repl. blade No. 712755 16.72 € 19.90 €

E SILKY® OYAKATA 270 - COARSEThis robust folding saw with its high cutting performance is ideal for pruningtrees. To enable a low friction and cleancutting surfaces, the blade has been tapered and has no set. A clean cuttingsurface helps water to run off quickly andthus lets the wood dry more quickly andprevent rotting. The specially ground rakerteeth reduce the cutting wear of the otherteeth, thus they increase the tool's service life and prevent clogging.

No. 712738 49.41 € 58.80 €Repl. blade No. 712838 25.13 € 29.90 €

E

A

1 2

F SILKY® BIG BOY - COARSEMaximum cutting performance:The chrome-plated taper-ground sawblade is rust-proof, the impulse hardenedtooth tips ensure great durability. The curred line of the teeth makes for particularly effective cutting. The sturdyyet lightweight aluminium handle can beused with one or both hands, while therubberised grip makes it easy to holdeven in difficult conditions as well ascushioning vibrations. Simply press abutton at your thumb to lock and unlockthe folding saw.

Blade length 360 mmOverall length 760 mmBlade width 42 mmBlade thickness 1.45 mmCrosscut teeth 5 mmNo. 712721 56.55 € 67.30 €Repl. blade No. 712722 31.43 € 37.40 €

F

C JAPANESE FOLDING SAW DELUXE 240The details make the difference to indus-trially-manufactured series products. Forexample, the blade of this saw is taper-ground 0.2 mm, and the teeth sides arepolished to make cutting even easier.Clearing teeth prevent clogging. Manualstraightening on the aligning anvil by themaster saw-smith himself ensures that

No. 712107 52.86 € 62.90 €Repl. blade No. 712108 27.65 € 32.90 €

B ALUMINIUM FOLDING SAW 150Compact featherweight for trekking andcamping:The solid aluminium handle, rubberized,non-slip grip and the sturdy, hard chrome-plated blade make this featherweight sawperfectly suited for outdoor activitiessuch as hunting, camping and trekkingtrips. The blade is taper-ground to reducefriction.

No. 712748 20.92 € 24.90 €Repl. blade No. 712847 12.52 € 14.90 €

CB

Blade length 150 mmOverall length 330 mmBlade width 30 mmBlade thickness 0.8 mmSetting 1.3 mmCrosscut teeth 3.5 mm

the saw blade runs smoothly. CurvedKashi body with rounded edges. Blade length 240 mmOverall length 525 mmBlade width 35 mmBlade thickness 0.6 mmSetting 0.9 mmCrosscut teeth 2 mm

Blade length 250 mmOverall length510 mmBlade width 32 mmBlade thickness 0.80 mmSetting 1.15 mmCrosscut teeth 2.70-3.60 mm

The hardchrome-plated (rustproof) bladewith impulse-hardened cross-cut toothpattern provides a high wear-resistance.Robust frame made of die-cast aluminiumand a rubberised, non-slip grip.Blade length 270 mmOverall length 560 mmBlade width 35 mmBlade thickness 1.30 mmCrosscut teeth 2.80 mm

D

Whether for gardening or trekking – thiscompact folding saw with its razor-sharpteeth easily stand the comparison withbigger saws. The robust metal foldingmechanism locks the blade in two different positions. The taper-groundblade reduces friction, and the soft elas-tomer non-slip handle is very comfortableto hold. The tapered blades have addi-tional raker teeth in order to reduce the

cutting wear of the other teeth and thusincrease the tool's service life. The teethare impulse-hardened.Comes with arobust, trans-parent plasticsheath thatcan be worn on a belt.Blade width 30 mm Crosscut teeth 3 mm

For more pruning saws see our webshop at www.more-than-tools.de

Tool handles without toxins (all plastichandles are regulary tested).


236

Fixed blade pruning saws

G SUPER SPEED PRUNING SAWThe curred, taper-ground blade ensuresparticularly high performance, capable ofdealing with even thick branches. Ergonomic hardwood handle, no sheath.Blade length 330 mmOverall length 500 mmBlade width 50 mmBlade thickness 1.2 mmSetting 1.7 mmCrosscut teeth 4 mmNo. 712742 20.92 € 24.90 €Repl. blade No. 712842 15.63 € 18.60 €

E UNIVERSAL PRUNING SAW

No. 712040 15.55 € 18.50 €

F WIRE SAWIdeal for camping and trekking:Our most compact saw consists of a spiraltoothed wire with two pullrings. It can even be used tomake a very effective framesaw with the help of a flexiblebranch. Cuts wood, plastic,plaster, limestone and metals.Length 500 mmØ 1 mm12 gNo. 712520 5.80 € 6.90 €

B CLASSIC PRUNING SAWThese pruning saws are made exclusivelyfor DICK customers by a leading Japan-ese manufacturer. Its slender designmakes it ideal for pruning fruit trees,trimming hedges and bushes. Taper-ground blade with coarse trapezoidaltoothing for excellent cutting perform-ance, coated for rust-proofing. Untreatedbeech handle absorbs moisture, preventing blisters.Comes in a beechwoodcase with a belt loop.

Classic 240Blade length 240 mmOverall length 390 mmBlade width 35 mmBlade thickness 0.8 mmSetting 1.2 mmCrosscut teeth 4 mmNo. 712116 23.45 € 27.90 €

Classic 270Blade length 270 mmOverall length 420 mmBlade width 35 mmBlade thickness 0.8 mmSetting 1.2 mmCrosscut teeth 4 mmNo. 712117 25.13 € 29.90 €

C KOBIKISturdy saw for forestry work. This sawcan cut thick branches and even smalltrunks in just a few strokes. Differentialtoothing (tooth size increases towards thetip of the blade) allows smooth,fast cuts to be made. Hardwoodhandle and sheath, with beltloop.

Kobiki 300Blade length 300 mmOverall length 450 mmBlade width 40 mmBlade thickness 1 mmSetting 1.5 mmCrosscut teeth 3.2-4 mmNo. 712723 27.65 € 32.90 €

Kobiki 330Blade length 330 mmOverall length 480 mmBlade width 40 mmBlade thickness 1 mmSetting 1.5 mmCrosscut teeth 3.5-4.5 mmNo. 712724 29.83 € 35.50 €

D KENRYU® POWERGRIPThese slender professional pruning sawscope easily with all domestic gardeningtasks and are equally suited for profes-sional forestry applications. Taper-groundblade, ergonomic handles with non-slip,rubberized grips. Comes with alocking plasticsheath with beltloop.

Kenryu® Powergrip 270Blade length 270 mmOverall length 440 mmBlade width 35 mmBlade thickness 0.8 mmSetting 1.2 mmCrosscut teeth 4 mmNo. 712743 26.47 € 31.50 €

Kenryu® Powergrip 300Blade length 300 mmOverall length 470 mmBlade width 35 mmBlade thickness 0.8 mmSetting 1.2 mmCrosscut teeth 4 mmNo. 712760 28.74 € 34.20 €

B C

D E

F

G

A SILKY® KATANA BOY 500The latest and biggest model by Silky, forcarpentry work, tree care and forestry caneasily stand the comparison with the Katana, the legendary Samurai sword.The taper-ground blade with no set helpsto reduce friction to a minimum, there-fore you can saw with only little pressure,leaving the cutting surface grooveless.A clean cutting surface helps water torun off quickly and thus lets the wood drymore quickly and prevent rotting. With itsblade length of 500 mm, this saw is idealfor cutting larger stock. Also ideal forgreen wood and construction wood. Therobust, yet lightweight aluminium handleis suitable for use with both hands, andwith its rubberised coating it remainscomfortable to hold even in difficult conditions. The folding saw is locked andunlocked in a safe and easy way, simplyby pressing a thumb and using a knurledscrew, which is located at the catch

spring. The rustproof, hard-chrome-plated blade with impulse-hardened teeth providesa long service life. Comes with a robustnylon shoulder bag with Velcro fastenerand pocket for replacement blades.Blade length 500 mmOverall length 1180 mmBlade width 50 mmBlade thickness 1.5 mmSetting 1.9 mmCrosscut teeth 6 mmNo. 712048 138.66 € 165.00 €Repl. blade No. 712049 64.71 € 77.00 €

An excellent handy all-round saw for the hobby gardener. Comfortable pistol-shaped handle and hardwood sheath.Without setting.Blade length 210 mmOverall length 340 mmBlade width 35 mmBlade thickness 0.7 mmCrosscut teeth 2.5 mm

Repl. blade No. 712822 15.63 € 18.60 €

Repl. blade No. 712827 16.55 € 19.70 €

Repl. blade No. 712827 16.55 € 19.70 €

Repl. blade No. 712829 18.40 € 21.90 €

Repl. blade No. 712823 16.22 € 19.30 €

Repl. blade No. 712824 18.40 € 21.90 €

A


237

B KOBIKI CLASSICTraditional Japanese forestry saw with ex-cellent cutting performance thanks to diffe-rential toothing. It cuts through even bran-ches as thick as your arm with just a fewstrokes. Angled wooden handle with han-ging loop, also suitable for two-handed use.Blade length 330 mmOverall length 510 mmBlade width 50 mmBlade thickness 0.9 mmSetting 1.3 mmCrosscut teeth 4.5-5.5 mmNo. 712788 18.40 € 21.90 €

No. 712740 58.74 € 69.90 €Repl. blade No. 712840 17.56 € 20.90 €

Telescoping pruning saws

D SILKY® PROFESSIONAL TELESCOPING SAWS For professional use:Professional telescoping saws for use intree maintenance and forestry. The curvedand hard chrome-plated blade guaranteesoptimal cutting performance, and the largerubber grip makes sawing virtually effort-less. Double-sided sickle-shaped stopper,two tilt positions. The strong, ellipticallyshaped aluminium shafthas ball catches andstoppers. Robust bladesheath included.

1 Four-part, 6.30 mBlade length 390 mmOverall length 2.44-6.3 mBlade width 60 mmBlade thickness 1.5 mmSetting 2.2 mmCrosscut teeth 4.5 mm3.05 kgNo. 712045 242.86 € 289.00 €

2 Three-part, 4.90 mBlade length 390 mmOverall length 2.35-4.9 mBlade width 60 mmBlade thickness 1.5 mmSetting 2.2 mmCrosscut teeth 4.5 mm2.25 kgNo. 712046 192.44 € 229.00 €

E JAPANESE TELESCOPING PRUNING SAW

No. 712728 57.90 € 68.90 €Repl. blade No. 712828 23.03 € 27.40 €

F SILKY® LONGBOY FOLDING POLE SAWLong and extremely effective:

No. 712050 204.20 € 243.00 €Repl. blade No. 712051 37.82 € 45.00 €

C SILKY® ZORIN TIMBER SAWExceptional cutting performance:A large saw for felling small trees and re-moving thick branches. The rubberized,pistol-shaped handle allows you to gripwith both hands. The extremely sharp,differential toothing ensures maximumcutting performance. Taper-ground, hardchrome-plated blade. Sturdy ABS sheath,with fastener and removable carryingstrap.Blade length 370 mmOverall length 610 mmBlade width 50 mmBlade thickness 1.3 mmSetting 1.8 mmCrosscut teeth 5-6.5 mmNo. 712757 83.11 € 98.90 €Repl. blade No. 712759 46.97 € 55.90 €

D

E

F

B

C

1

2

A

A Z-SAW® MULTI-SAW 273Multi- purpose saw for fruit trees and general pruning work. The blade can betilted relative to the handle so you can always find the ideal cutting position evenunder awkward conditions. A coating withTeflon minimises the friction and pro-tects the blade from rust. A sheath withremovable belt loop makes it easy to carry.

Beech handle.Blade length 270 mmOverall length 460 mmBlade width 45 mmBlade thickness 0.8 mmSetting 1.1 mmCrosscut teeth 2.4 mm

Lightweight but sturdy telescoping sawfor tree maintenance. Steplessly tele-scoping, two-part aluminium handle.Slender blade with proven Japanese cutting power. The head can be unscrewedto make transport and storage easier.Blade length 300 mmOverall length 2.1-3.4 mBlade width 35 mmBlade thickness 1 mmSetting 1.6 mmCrosscut teeth 4 mm1.2 kg

The »Silky Longboy« telescope, foldingsaw is the first choice of professionalsworking in forestry and for fruit tree care.The saw is telescopic up to 3.6 metres,providing two securely locking poles, while when folded it only has a length of1.45 metre. The taper-ground blade withno set helps to reduce friction to a mini-mum, therefore you can saw with onlylittle pressure, leaving the cutting surfacegrooveless. This clean cutting surfacehelps water to run off quickly and thuslets the wood dry more quickly and pre-vent rotting. The hardchrome-plated(rustproof) blade with impulse-hardenedteeth provides a long service life. Thecurved teeth line helps the teeth enterthe wood in different depths and thusprovide a maximum cutting performance.With the hook at the end of the blade youcan easily pull smaller branches towardsyou. Due to the lightweight aluminiumconstruction you can work in an effortlessand tireless manner. The metalfolding mechanism lets you easily fold away the blade. Comes with break-proof sheathto be fastened to the handle.Blade length 360 mmOverall length 1.8-3.54 mBlade width 55 mmBlade thickness 1.6 mmCrosscut teeth 4.3 mm2.1 kg

Repl. blade No. 712047 66.39 € 79.00 €

Repl. blade No. 712047 66.39 € 79.00 €

Garden tools || Scythes and accessories

238

Scythes and accessories

Mowing with a scythe is not only an envi-ronmentally-friendly alternative to lawn-mowers, but also perfect exercise. Therhythmic mowing movements train yourarms and upper body, the silence and thearoma of freshly-mown grass have an al-most meditative effect. A must-have foruninterrupted enjoyment is a well-ba-lanced scythe which retains its sharpness for a long time.

A SCHRÖCKENFUX® SCYTHESSchröckenfux, a company from the Austrian Krems Valley, is one of the lastscythe makers in central Europe. For over450 years, carbon-steel blanks have beenshaped to elegantly curved, razor-thinscythe and sickle blades.

1 »Original Razor-Cut« gardening scytheUniversal scythe with a slender peenedblade, patented snath (153 cm), ad-justable for height and body position,oval steel tube with wooden handles.Completely ready for mowing, instructions are included.Blade width 50 mmBlade length600 mm No. 705600 69.66 € 82.90 € Repl. blade No. 705602 36.05 € 42.90 €700 mm No. 705601 71.34 € 84.90 € Repl. blade No. 705603 38.57 € 45.90 €

DVD - SCYTHING TECHNIQUESIn this introduction,scythe-master ErnstSchoiswohl and Cana-dian organic farmerPeter Vido, teach know-ledge which has virtu-ally been forgotten.From adjusting thesnath, body positionwhen mowing, to peening and honing theblade, viewers will learn everything theyneed to know about working with scythes.DVD - 20 minutes.No. 713752 7.48 € 8.90 €

Peening and honingTo preserve its sharpness, a scytheblade must be regularly honed andperiodically peened along its cuttingedge. This cold-hardens the metal andmakes the grain finer, which makes iteasier to sharpen and increases itsdurability. It also thins the cuttingedge, improving the cutting perform-ance. Peening using a hammer andanvil is an art which is mastered byonly a handful of craftspeople today.The use of the peening jig simplifiesthe task.

H PEENING JIGFor controlled peeningof scythe and sickleblades. Round anvilwith stop, centring pinfor holding in a woodenblock. Two striking sleeves for coarse and fine peening.800 gNo. 705591 41.93 € 49.90 €

2 Brush scytheIdeal for controlled mowing of weeds andundergrowth along hedges or on fruit treemeadows. The blade is shorter and th-icker than grass blades, and is not easilydamaged when it hits a foreign body. Thesnath can be adjusted for height (170 –185 cm) and body position. Whetted andsharpened ready for mowing, with instructions.Blade length 50 cmBlade width approx. 60 mmNo. 705607 68.49 € 81.50 €Repl. blade No. 705608 36.05 € 42.90 €

3 Ash wood snathOptimal body positioning for mowing via adjustable handles and S-shape. Fits Schröckenfux and all standardscythe blades. Snath cross section 26 x 30 mm

Overall length 185 cmFor individuals 155-185 cmNo. 705609 54.54 € 64.90 €Overall length 195 cmFor individuals 185 cm and up in heightNo. 705610 56.22 € 66.90 €

E PEENING ANVILDie forged steel anvil with a polished face for peening scythes and a horn for fastening on wooden blocks. The scytheblade is laid on the anvil, the cutting ed-ge is peened with the hammer. For de-tailed instructions on peening scythes,we recommend the DVD »ScythingTechniques« (No. 713752). Face 40 x 40 mmHeight 100 mm500 gNo. 705664 21.60 € 25.70 €

G PEENING ANVIL WITH STOPPERPeening made easy:Peening makes the cutting edge of scy-the and sickle blades thinner, harder andeasier to sharpen. But peening is quite achallenge. A well balanced blow with thehammer, an even feed motion and a pre-cise positioning of the blade on the anvilare required. All demand a lot of practise.This new peening anvil solves this pro-blem. The blade is placed on an adjusta-ble support plate. A depth stop makessure that the blade is exactly positionedon the domed anvil. Another advantage:you can always easily view the field ofwork. The anvil is made of impact-resis-tant steel, the surface area is hardenedto a depth of 3 cm to 62 HRC. Becausethe anvil is not hardened through thehammer will not bounce.We recommend a square hammer with aslight crown and a head weight of approx.600-800 g, e.g. No. 714104 . Suitedfor all scythe and sickle blades. The anvilhas a horn for beating it to a woodenblock.Includes instruction sheet and abrasiveweb for cleaning blade, anvil and hammer.Galvanized.800 gHeight 100 mmNo. 705587 60.42 € 71.90 €

Learn to mow with a scythe and howto peen the blade in our Scythe workshop,see www.more-than-tools.de/workshops

C PEENING HAMMER

No. 714115 18.82 € 22.40 €

B WHETSTONENatural sandstone, perfectly shaped forhoning scythe and sickle blades. Elliptical shape.215 x 30 x 16 mmNo. 705582 9.16 € 10.90 €

D COWHORN WHETSTONE HOLDERThis traditional-style whetstone holder ismade of natural, polished Austriancowhorn. Offers an even classier way ofkeeping your whetstone wet and withinreach when scything large areas. Fittedwith a belt clip.No. 705590 26.81 € 31.90 €

F COPPER WHETSTONE HOLDERFill the container with water and wear iton your belt! The perfect device for keep-ing your whetstone wet and handy whenscything large areas. Copper, with a beltclip.190 x 75 x 40 mmNo. 705589 15.04 € 17.90 €

A

1 2 3

D F

B

EC H

G

Hammer with die forged head and pol-ished faces for peening scythes. Ergono-mically shaped shaft made of copperbeech secured with an annular wedge.Head weight 600 gShaft 230 mmOverall length 255 mm

Garden tools || Sickles

239

Sickles

A JAPANESE SICKLES

1 Damascus-steel sickleThe powerful blade of this multi-layer Damascus steel sicklecuts through even thestrongest grasses,weeds and undergrowth effortlessly. Harvesting salad and vegetables with it isa pleasure.Blade length 155 mmOverall length 400 mm365 gNo. 718161 83.95 € 99.90 €

2 Farming sickleSickle with thick blade. Cuts branches,undergrowth and brush. 4 mm thickthree-layer steel blade.Blade length 180 mmOverall length 430 mm460 gNo. 718152 33.53 € 39.90 €

4 Grass sickleUltralight:Sickle for fine grasses and delicateherbs. Thin two-layer blade.Blade length 180 mmOverall length 385 mm120 gNo. 718119 27.31 € 32.50 €

6 Drop-point farming sickleWith three-layer, robust head for removingbrush and clearing undergrowth.Blade length 170 mmOverall length 500 mm430 gNo. 718156 36.89 € 43.90 €

3 Grass sickle, crankedStrong sickle for toughgrass, herbs and undergrowth.Blade length 195 mmOverall length 560 mm200 gNo. 718151 25.71 € 30.60 €

C JAPANESE CLEAVERSharp and three-layered:Universal cleaver for tree care and gardening. The sharp blade cuts throughthumb-sized branches with ease, thesickle shape makes it easier to removeundergrowth, reeds and thick-stemmedherbs. Cord-wound handle with hangingeyelet.Blade length 170 mmOverall length 430 mm620 gNo. 718163 75.55 € 89.90 €

B SICKLE HOEShort, L-shaped hoe for weeding and loosening soil. Cranked blade hand-forgedfrom double-layered steel.Blade length 120 mmOverall length 375 mm190 gNo. 717907 15.88 € 18.90 €

5 Harvesting sickleCompact sickle with toothed blade, idealfor harvesting salad, vegetables and herbs.Blade length 170 mmOverall length 350 mm100 gNo. 718150 8.32 € 9.90 €

D SICKLE CLEAVER

No. 708360 83.19 € 99.00 €

E FRENCH MACHETEThe long established manufacturerSabatier has supplied the French ForeignLegion with this machete for decades.However, the extra-long sturdy carbon-steel blade is not only suitable for survival training in tropical rainforests.This machete is an ideal tool for forestry,gardening, hunting or fishing. It is easyto sharpen and retains its edge even afterheavy-duty work. Thick leather case withbelt loop.Blade length 550 mmOverall length 710 mm1000 gNo. 705620 88.15 € 104.90 €

For garden hatchets see chapter axes and hatches.

A

5 6

D E

B C

21 3 4

These hand-forged sickles are feather-light and extremly sharp, making garden-ing work much easier. Their handles consists of water-resistant Japanese hardwoods like ho or white oak.

This tool is made to be used for clearingundergrowth and containing rank growth.Due to its long cutting edge, you can alsocut thorny wood up to 2 cm branch diameter from a safe distance. The hand-made untreated ashwood handlewith its rounded end makes sure that the tool can be held firmly and safely without slipping. Approx. 55-57 HRC.Head weight 750 gBlade length 320 mmOverall length 910 mm

Garden tools || Gardening sets, Gardening accessories and useful items

240

Gardening sets

A JAPANESE GARDENING SET, 7-PIECESFor Professionals:

No. 718916 125.21 € 149.00 €

Price advantage

»All a Gardener’s Heart Desires« Magazine »Wohnen & Garten«(Home and Garden), 2008

B JAPANESE GARDEN TOOL SET, 5 PIECESGood start:

No. 712633 67.14 € 79.90 €

Price advantage

Gardening accessories anduseful items

C GARDENING APRONThe stylish way to always have all impor-tant tools ready at hand: practical hipapron made of thick cotton with fine leather, 6 pockets reinforced with rivets.32 x 64 cmNo. 707501 38.24 € 45.50 €

E COTTON APRONWhether you are turning, gardening orsculpting - this French apron simply makesworking more enjoyable. The hefty cottonfabric is impregnated to repel water anddirt. The large, sealable front pocket isperfect for tools and materials while thesmall pouch serves to keep your glasses.Size60x82 cm No. 707505 29.33 € 34.90 € 90x87 cm No. 707506 33.53 € 39.90 €

G JAPANESE RUBBER BOOTSCult object:Japanese boots with separate big toe provide a better footing, improve thewearer’s sense of balance and circulation. Insiders have long considered these tra-ditional boots to contribute significantlyto the extraordinary long lifespan of theJapanese. To us, these eye-catchers haveall the makings of a cult object. Formowing, in the garden, for pond mainte-nance or just to show off. A small nippleon the heel makes the boots easy to takeoff. Ribbed cotton cuff. Natural rubber,nylon inside. Wear these boots with 5-toesocks No. 707667.SizeM (38-39) No. 707662 33.53 € 39.90 € L (40) No. 707663 33.53 € 39.90 € LL (41-42) No. 707664 33.53 € 39.90 € 3L (43) No. 707665 33.53 € 39.90 €

F 5-TOE SOCKS - FOUR PAIRS

D JAPANESE GARDENING GLOVESThese thin, cosy gardening gloves madeof finely perforated pigskin facilitate pre-cise control of tools and plants. Innerlined with full-grain leather for bettergrip, Velcro fastener on cuff.Size M = 7, L = 8, XL = 9-10SizeM No. 707655 7.48 € 8.90 € L No. 707656 7.48 € 8.90 € XL No. 707657 7.48 € 8.90 €

H HEMP STRINGThe plant friendly, black hemp string is traditionally used in Japan for tying bamboo fences and trellises when shap-ing bushes and trees. It is highly tear-resistant, non-elastic and easy to knot.Overall length 200 mØ 3 mmNo. 708891 11.68 € 13.90 €

I PIPE CUTTERFor cutting flexible ho-ses (PVC, rubber etc.)up to a diameter of37mm. Stainless spe-cial toughened steel(58 HRC), suitable forsharpening. Aluminium handles. Overall length 205 mmNo. 717832 10.00 € 11.90 €Repl. blade No. 717833 2.94 € 3.50 €

J WIND-CHIME HOUSEThis miniature of a Buddhist bell houseadds a touch of Asian atmosphere to yourgarden. Cast-iron pagoda and miniaturebell, surface black annealed for rust-proofing.185 x 185 x 130 mm1700 gNo. 820034 37.73 € 44.90 €

K WIND BELLSCast iron bell whose tender tones playthe song of the wind. Surface ornament-ed in the style of a Buddhist temple belland with green patina. 110/185 g

Ø1 50 mm No. 820032 6.47 € 7.70 € 2 60 mm No. 820033 7.48 € 8.90 €

A

B

C

D

H

I

J

F GE

K

1 2

Professional set of Japanese quality toolsfor pruning and planting. It includes theKijo pruning shear (No. 718169) for cut-ting without damaging the plant, a SilkyPocket Boy 170 mm folding saw (No.712776), a universal planting, rootingand transplanting knife (No. 718157), aflower and all-round shears (No. 718099),the sickle knife for harvesting and cuttingweeds (No. 718158) and the Japanesegarden knife (No. 709169), stylishlyhoused in the gardening apron made ofsplit leather (No. 707501).

With this professional set of Japanesegardening tools, you are optimally equipped for pruning and other work with plants. It contains a Dick classicpruning saw (No. 712116) in a beech-wood sheath for trimming fruit trees and hedges, the lightweight (205 g) Kijo pruning shear (No. 718169), a Japanesegarden knife (No. 709169), and a sheathed planting knife (No. 718157)for replanting potted and outdoor plants.Practical storage and transport with thetool roll (No. 707514) made of strongcotton cloth with clip fastener.

Seamless knitted socks with separate toes, in keeping with Japanese tradition.They allow better airing, and so help pre-vent sweating and athlete's foot. Blendedfabric of 85% cotton and 15% nylon.One size, black.No. 707667 8.07 € 9.60 €

Wooden Objects | 242

Horn products | 243

Metal objects | 243

Leather products | 244

241

Handicraft at its best!

Handicraft || Wooden objects

242

Wooden objects

A PUZZLE BOXES (HIMITSU BAKO)Himitsu Bako boxes are certainly amongthe most intriguing hand-crafted woodenobjects made in Japan. At first glance,they appear to be nothing more than sim-ple boxes with intricately inlaid surfaces.Try to open them and you will quicklydiscover that their intricacy is more thanjust cosmetic. The panels must be ma-nipulated in a pre-set series of steps torelease the locking mechanisms hiddenby the mosaic and allow the lid to slideopen. The production of these highly pre-cise mechanisms is a challenge which re-quires decades of experience - theyoungest master Himitsu makers are over60 years old. Made of solid cedar inlaidwith different types of natural wood. So-lution included.

1 Himitsu Bako, 5-sun*21-step.150 x 95 x 70 mmNo. 820036 82.35 € 98.00 €

2 Himitsu Bako, 4-sun*7-step.120 x 80 x 55 mmNo. 820035 43.61 € 51.90 €

3 Himitsu Bako Mini, 2.5-sun*4-step.73 x 60 x 50 mmNo. 820047 23.45 € 27.90 €

* sun = traditional Japanese unit, approx. 30 mm.

B URUSHI BOWL BY HIROYUKI WATANABEVarnishing artist Hiroyuki Watanabeworks in a remote Japanese mountain vil-lage named Shionofuchi, not because hewishes to flee modern civilization but be-cause of the necessity of working in anenvironment completely free of dust. Heturns the wooden bowl blanks himselfusing Keyaki wood. The finish consists ofat least 13 coats of Urushi, each ofwhich must dry for an extended period oftime in a steam chamber (Urushi actually»dries« by absorbing water). The groundcoat and porefiller Mr. Watanabe uses ismade of Ki-Urushi and powdered clay.The edges of the bowl are reinforced withcotton fabric and 7 additional layers ofUrushi, each of which is increasingly fineand has been smoothed with a charcoalabrasive. The last coat consists of pureJo-Shuai-Urushi, which lends the piece a No. 831019 125.21 € 149.00 €

Urushi has been extracted from theAsian tea tree (rhus vernicifera) forover 6000 years. It is waterproof,food-safe, resistant to alcohol and sol-vents, does not become brittle orcrack with age and develops a beauti-ful patina with use. The limited pro-duction capacity may lead to shippingdelays.

C LEIHO STOOLA unique piece from our master workshop: It can be used as chair or table, or otherway up, for storing firewood or magazi-nes. Unobtrusive elegance and perfectform characterise our LeiHo stool.

This versatile piece of furniture is craftedwith great care in the DICK workshop.Thin slats of walnut and maple provide acharming contrast. LeiHo is a highly ver-satile piece of furniture and an eye-cat-cher for every home.Finished with a fragrant mixture of organ-ic linseed and orange oil.Width 400 x depth 345 x height 450 mmNo. 831241 125.21 € 149.00 €

deep, clear, magical gloss unmatched byany other surface finishing technique.The bowls additionally feel wonderful tothe touch due to Urushi's naturalwarmth. Each bowl is signed by MasterWatanabe and comes in a elegant display box.Ø approx. 120 x 70 mm

A

1

2

3

B

C

No. 719108 75.55 € 89.90 €

Handicraft || Horn products, Metal objects

243

Metal objects

E JAPANESE LETTER OPENER COPPER AND STEELDagger-shaped three-layered JapaneseLetter Opener, made of attractivelystructured copper, iron and Blue PaperSteel. The blade is sharpened. The LetterOpener features a decoratively plaitedcord made of dark brown leather.The Blue Paper Steel (not stainless) ofthe cutting edge layer consists of veryclean high carbon-steel which is used forhigh grade knives and the famous Japa-nese swords.Blade length 90 mmOverall length 180 mmBlade thickness 2.5 mm32 gNo. 719364 25.13 € 29.90 €

F LETTER OPENER KATANAElegant:Sword-shaped letter opener, forged inMaster Swordsmith Yamamura’s work-shop. Polished, stainless steel blade withimitation hamon (tempered edge).Handle and sheath made from Ho (Mognolia wood).Blade length 105 mmNo. 719067 12.52 € 14.90 €

G MOKUME LETTER OPENERThis opener offers connoisseurs of fineJapanese blades a stylish way of openingtheir mail. The blade consists of a lami-nation of various metals forged in theshape of a Kozuka (small knife normallycarried together with Japanese sword).The surface of the letter opener has beenetched and polished to reveal an intrica-tely figured metal surface very similar towood grain patterns (Mokume).190 x 12 x 2 mm

Horn products

For centuries hornware has proven itselfin daily use. This natural material doesnot only offer a distinctive appearancebut also a variety of positive features.Genuine horn products are safe to use,food safe, free from toxins and tastelessas well as acid-proof and color-fast.These features make horn products the

A DECORATIVE FRUIT BOWLA bowl versatile and impressive as natureitself. The organic form is attained by aspecial handcraft technique. The diffe-rent shades of color of the horn lend thebowl a unique haptic impression and na-tural elegance.Approx. 390 x 230 x 180 mmNo. 820153 66.39 € 79.00 €

B MOSAIC JEWEL CASEThe horn plates in bright and dark sha-des harmonise in an amazingly interes-ting overall picture.

The inner wooden body, made of teak-wood, assures stability and offers a beau-tiful contrast to the exterior.185 x 135 x 75 mmNo. 820156 50.34 € 59.90 €

C SALT AND PEPPER SHAKERThis set appeals by its pure design andthus has a modern look. A lock underne-ath the shakers enables you to refillthem. A tray, made of black varnishedwood gives this accessory a special touch.95 x 55 x 45 mmNo. 820160 20.92 € 24.90 €

D SALAD SERVERS »OPI«Classy salad servers made of several hornlayers. The convex and corrugated handlesare not only very aesthetic but also liewell in your hand and thus meet allfunctional expectations. Overall length 290 mmNo. 820155 25.13 € 29.90 €

ideal kitchen tool and accessory. Likeevery other natural material, horn is nothomogeneous in colour and shape.Therefore each single horn product isunique due to its finish and material!

E

F

G

A

B

C

D

Handicraft || Leather products

244

Leather products

B LEATHER ART »INDEN-YA« POUCHESSince the 16th century, a Japanese fami-ly business has dedicated itself to themanufacture of leather product orna-mented with patterns from Urushi lac-quer. Back then, they mainly producedprotective leather garments for Samuraiwarriors, while today they make leatherproducts for everyday use. The softestdeer leather is smoke-stained and thendyed using a traditional Indian tech-nique. The decorative pattern is subse-quently silkscreened onto the leather byhand, using the traditional Urushi varnishused derived from natural tree resin.

Blue drawstring pouch with dragonflypattern for keeping small treasures.Deerskin printed with Urushi patternsand black silk lining.120 x 110 mmNo. 820007 41.93 € 49.90 €

A REINDEER LEATHER PRODUCTSReindeer leather is particularly pliable andsoft. It is traditionally used for makingmittens, shoes, hats, jackets and bags.The products offered here are made 200km north of the arctic circle near the bor-der between Sweden and Finland.

1 PouchFor small or delicate objects such as je-wellery, coins, watches. In Sweden theyare also used for storing spices and cof-fee.150 x 70 mmNo. 820101 23.45 € 27.90 €

4 Wallet

Made of finest reindeer leather. 2 Euro-compatible bill compartments, creditcard slots and zipper pocket for coins.100 x 125 mmNo. 820103 38.57 € 45.90 €

2 Mono backpackA backpack that fits like a glove, ideal forstorming both wooded and urban jungles.The single padded strap is carried diago-nally over the left shoulder, the additio-nal strap has two plastic buckles to pre-vent the pack from moving around duringuse. Padded back panel, main compart-ment with large zipper, side compartmentlined with water resistant fabric and a setof leather loops (for the transport ofsmall game) and a leather phone/GPS po-cket attached to shoulder strap.Volume ca. 20 litresca. 45 x 36 x 17 cmca. 650 gNo. 820100 167.23 € 199.00 €

3 Small backpackOutside pocket with wide, adjustable car-rying straps, loop handle and reindeerhorn fittings.Volume approx. 15 litresApprox. 32 x 28 x 18 cmApprox. 740 gNo. 820105 154.62 € 184.00 €

C LADIES´ RAY LEATHER PURSEFrom the depths of the ocean directly tothe runway of the fashion capitals: thisfascinating ladies´ purse from undulateray leather guarantees a grand entrance.

12 card holders and 5 lengthwise com-partments, one of which has a zip.Approx. 180 x 100 x 20 mmNo. 830864 82.35 € 98.00 €

D MEN'S STINGRAY WALLETThe linear structure of the stingray makesthis wallet a real eye-catcher.

2 inside pockets for notes, a coin com-partment with press button, 3 credit cardholders.Approx. 115 x 95 x 10 mmNo. 830865 66.39 € 79.00 €

E LADIES’ SALMON LEATHER PURSEHigh-quality black calf-leather purse withan appliqué of vegetable-tanned salmonleather in natural colour. Made complete-ly by hand, the salmon leather is proces-sed in such a way that the natural shapeof the fish isretained. Anexceptionallydurable pursewith a dis-tinctive look.6 credit cardslots and 3full-widthcompart-ments, 1compartment with zip.Approx. 185 x 100 x 25 mmNo. 830867 74.79 € 89.00 €

F SALMON-LEATHER MANICURE SET

No. 830869 54.54 € 64.90 €

B

A

1

4

2

3

C D E F

Classy mani-cure set withsolid-colou-red, pale sal-mon-leathercase includingnail scissors,nail file, nail clippers and tweezers. Thebeautiful salmon leather is also used in-side the case to hold the items in place.Compact shape means it fits into anyhandbag.120 x 65 x 20 mm

245

Wood | 246

Sculpting and carving | 246

Joinery, furniture making | 247

Carpentry, architecture | 247

Woodturning | 248

Finishing, restoration | 248

Bow making | 248

Boat building | 249

Tools | 249

Knives and sharpening | 249

Forging | 250

Traditional techniques | 250

Garden and kitchen | 251

DVDs | 252

Instrument making | 252

Indispensable tutors on the path of learning!

SCHNITZEN LERNEN FÜR KIDSBy Robin Edward Trudel. Carving is a fascinating handicraft. It trains the fine motor skills, concentration and the awarenessof form. After a brief description of tools and a basic introduction towood carving, each chapter is devo-ted to a different age group. Step-by-step illustrations providemotivation and precise working instructions at the same time. Thissimple introduction to carving makes the reader want more! 96 pages, 342 coloured illustrations, hardcover, 170 x 240 mm, in German.No. 713852 20.56 € 22.00 €

GRÜNHOLZ SCHNITZEN - Ein kinderleichter Grundkurs by Tove YdeGreen wood is the ideal materialfor teaching children how tocarve because of its excellentworkability. With the help of thisbook, all aspiring woodworkerswill soon be able to make a variety of spoons, forks, combs,games, pipes and countlessother useful objects. The proper-ties of various species of European wood and the proper selection of tools and finishing materials arealso discussed. 71 pages with over 100 colour photos, hardcover, 245 x 225 mm, in German.

No. 713230 17.76 € 19.00 €

GRUNDKURS SCHNITZENBy Dick Onians. This in-depth technical book guides ambitious carvers from simple relief work tocomplex sculpted figures. The authorpays particular attention to designssuitable for the workpiece and theanatomy of humans and animals.183 pages, 275 photographs and65 illustrations, hardcover, 217 x 282 mm, in German.No. 713358 27.94 € 29.90 €

Books || Wood, Sculpting and carving

246

Price noteAs the German books are subject to the store priceagreement, we are obliged to pass on any pricechanges to our customers.

Wood

ATLAS DER HOLZARTENAtlas of wood types. 150 types ofwood in words and pictures. Thiscomprehensive atlas of wood intro-duces 150 types of wood and provi-des instruction on their uses. Cleartables in several languages scientifi-cally document the wood types.Each wood’s growth, appearance,properties and utility are extensivelydocumented. 192 pages, 276 colourillustrations, 150 geographical maps,hardcover, 220 x 295 mm,in German.No. 713782 37.29 € 39.90 €

HOLZFÜHRER - EINHEIMISCHE HOLZARTEN MIT MAKROAUFNAHMENBy Jean-Denis Godet. This practicalguide to wood for foresters, gardenersand hobby joiners is an introductionto the 30 main domestic types ofwood. Detailed photographs of flo-wers, leaves, fruit and buds make iteasy to identify the trees. Lists thedensity and uses of the individualtypes of wood. 128 pages, 540colour photographs, softcover, 210 x 297 mm, in German.No. 713169 18.60 € 19.90 €

HANDBUCH DER HOLZBEARBEITUNGBy Albert Jackson and David Day. An excellently illustrated technicalbook, both for experts and trainees.The types of wood are introduced inlarge-format pictures, and furnituredesign principles are shown in elaborate exploded drawings. Other topics covered include tools,joints and surfaces and fittings.240 pages, over 1,200 colour illustrations, hardcover,210 x 260 mm, in German.No. 713519 32.71 € 35.00 €

See www.more-than-tools.defor more books on woodworking.

See www.more-than-tools.de for more books.

Sculpting and carvingThe more intensively one studies a particular subject,the more fascinating it becomes. Books are indispensablecompanions on the way to learning and new discovery,as are DVDs and workshops. The books we offer mainlyaddress the tools, techniques and traditions of workingwood by hand and metal-work. The selection processwe use is simple - all the books we offer have beenread by our own experts and selected for the quality oftheir content.

KLEINE SCHNITZEREIENCarving green wood - on the go and anywhere, by Chris Lubkemann. A small carving knife is enough tocarve replicas of the 18 green woodprojects described in the book.Whether for spoons, tools, animalheads, miniatures orflutes - you can findthe material you needby the side of theroad. Step-by-stepphotographs, carvingtricks and tips, reci-pes and outdoor tipsmake this book apleasure to read.98 pages, approx. 400 colourphotographs, hardcover, 170 x 240 mm,in German.No. 713763 17.76 € 19.00 €

SCHNITZENBy Jeremy Williams. This systematic introduction to woodand tools and the various carvingtechniques makes getting started incarving easier. Valuable tips preventbeginners’ mistakes; step-by-step instructions guide you towardsmastery of low- and high-relief car-ving and sculpture.128 pages, 360 illustrations, softcover, 170 x 240 mm,in German.No. 713287 16.64 € 17.80 €

SKULPTUREN AUS HOLZBy Josepmaria Teixidó í Camí and Jacinto Chicarro Santamera. An introduction to the art and technique of sculpture in wood. This fundamental book offers an in-depth introduction to the art ofsculpture and sculpting techniques.Wooden sculptures from differentperiods and cultures are introduced,as is the material wood. The creationof a range of sculptures is documen-ted, through the design, planning and implementationstages. 192 pages, 552 colour photographs, hardcover235 x 305 mm, in German.No. 713825 37.29 € 39.90 €

ORNAMENTALES SCHNITZENChamfering, low carving, relief carving. A book of patterns by FranzStadlhofer, Franz Leeb and JosefMader. A comprehensive collectionof ornamental, primarily Alpine motifs for decorating furniture, interiors, picture frames and woodentools, complete with their traditionalbackground. Technical details andinstructions for low carving, reliefcarving and text complete the book.160 pages, 400 drawings and colour photographs,hardcover, 213 x 285 mm,in German.No. 713304 23.36 € 25.00 €

SCHWEDISCHE SCHNITZ-SCHULEWorking with knifes and axes, byWille Sundqvist. This book by thegreat Swedish sculptor is characteri-sed by his love of wood and the carving tradition of his homeland.216 pages, 334 illustrations andphotographs, hardcover, 215 x 235 mm, in German.No. 713125 30.65 € 32.80 €

TOTEMPFÄHLE UND MASKEN SELBST GEMACHTBy Alan & Gill Bridgewater. Learn about the archaic world ofshapes of the North-West Pacific Indians based on twenty projects ofvarying difficulty. Totem poles,masks, chests and ritual items,richly ornamented with motifs from the world of shamans and spirits. Excellent detail draw-ings and sequence descriptions make it easier to approach this fascinating wood culture.194 pages,174 b/w illustra-tions, 4 colour photographs, softcover,210 x 280 mm, in German. No. 713730 27.85 € 29.80 €

By Chris Pye. This book presents 10 carving projects ranging from acarved copy of Dürer’s well-knownpainting of supplicating hands to aleaping frog. Each project is de-scribed in detail, from the initialidea to the finished work. Pye’s experience as a carving instructor allows him to thoroughly address allthe practical questions which arisein the planning and execution ofeach project. 165 pages, 309photographs, 29 b/w illustrations,softcover, 210 x 275 mm, in English.No. 713318 14.86 € 15.90 €

ELEMENTS OF WOODCARVING

WERKBUCH HOLZBy Declan O'Donoghue. This practical guide is a comprehen-sive and understandable introductionto the techniques of the craft ofwoodwork. The range of subjectsstretches from individual processingmethods and joints, to self-madeitems. The authors give ideas for designing your own projects andteach you to use manual and electrical tools and machines safely. Chapters on woods of the world, selecting the right wood and storing and preparing itround off this high-quality book. 232 pages, 900 colourphotographs, 8 b/w photographs, 100 line drawings, 3overview maps, hardcover, 245 x 285 mm, in German.No. 713743 18.60 € 19.90 €

See www.more-than-tools.defor more books on woodcarving.

Books || Joinery, furniture making, Carpentry, achitecture

247

Joinery, furniture making

MÖBEL AUS HOLZBy Sam Maloof. This book by master furniture maker Sam Maloof is just as ingenious as hiswonderful furniture. He teaches readers his sure sense of shape andhis profound love of working withwood with typical ease and clarity. Like a good friend, he allowsthe reader intensive and intimate insight into his creations, work andlife. Workshop photographs becomereal works of art, casual handwritten notes become calligraphic treasures and even the smallest sketchesradiate liveliness and joy. An eye-opener for anyone involved in furniture making.224 pages, 70 colour illustrations, 236 b/w photo-graphs, hardcover, 225 x 302 mm, in German.No. 713535 27.94 € 29.90 €

DER MÖBELBAUBy Fritz Spannagel. First publishedin 1954, this classic remains just astopical today. Its importance is deri-ved from the systematic instructions,descriptive illustrations and detaileddescriptions of the joints and othertechniques of woodworking craft. The book is largely intended for app-rentice and qualified joiners, but alsofor architects and woodwork teachers.368 pages, 1,538 illustrations, hardcover, 220 x 297 mm, in German.No. 713543 32.52 € 34.80 €

HOLZIS HANDBUCH FÜR SCHREINERBy Carsten Hilbert. Over 2,200 terms, from gluing on to bonds, help apprentice carpenters,qualified carpenters and ambitioushobby carpenters with any questionsthey might have. The comprehensiveknow-ledge of carpentry in user-friendly form, numerous tables andmany tips and tricks make this bookan invaluable companion.424 pages, 1,600 colour illustrationsand many useful tables, softcover110 x 180 mm, in German.No. 713876 26.64 € 28.50 €

VORLAGENBUCH MÖBEL & MEHRBy A. W. P. Kettless. 80 woodworking projects with arange of difficulties are presentedclearly in drawings, material listsand step-by-step instructions. Build shelves, tool-boxes, tables and chairs, garden furniture, gardengates, sheds, chests of drawers andeven simple boats. 240 pages,hundreds of drawings, hardcover,190 x 240 mm,in German.No. 713858 26.92 € 28.80 €

DAS GROSSE BUCH VOM STUHLBAUA woodworking compendium, byDrew Langsner. This fundamentalwork is far more than a guide tochairs. It expertly describes the selection and preparation of the required tools and equipment, sourcing, splitting and storing thewood, right through to making spokes,frame parts and seat surfaces. A wide range of types of spoke-backed chairs, Windsor chairs, American country-house designs, stools with wovenseats, children’s chairs, benches etc. are presented as projects. Instructions for making a sturdy joiner’sbench, a carving bench, a steam chamber, and a foot-operated woodturning bench complete this technicalbook which is a valuable aid for any woodworker.312 pages, 564 illustrations and 182 drawings, hardcover, 210 x 280 mm, in German.No. 713728 57.94 € 62.00 €

DAS GROSSE TÜREN-BUCH For carpenters, architects and teachers (1950), by Fritz Span-nagel. Over fifty years after its firstpublication, “The Door Book” is still the most comprehensive standard work for designing theseimportant construction elements.With his customary descriptiveprecision, the author comprehensivelyinforms the reader on wood,surfaces, machines, design types, fittings and shapesfor a wide range of applications. With 1,813 detailedindividual illustrations, templates, views and sectionaldrawings, this weighty book is indispensable for joiners,builders, architects and for teaching in vocational andtechnical schools. 502 pages, 1,813 illustrations,hardcover, 227 x 288 mm, in German.No. 713250 37.29 € 39.90 €

DIE WERKZEUGE DES JAPANISCHEN SCHREINERSby Toshio Odate. This re-issued book and the DVD with four instructional videos open the door to the fantasticworld of the art of Japanese joinery.You will not only learn how to sharpenprecisely and how to use gouges,planes, saws and marking tools, butyou can also follow their use with various sample applications. In the DVD, a Japanese carpentermakes a range of wood joints, and thebook’s author, Toshio Odate, demon-strates how to make a small sliding door.

Book: 198 pages, numerous b/w photo-graphs and drawings, hardcover, 245 x 310 mm,in German.DVD: 4 films, 135 min, in German.No. 713779 33.53 € 39.90 €

Price advantage

Design, building techniques, objects, by Daniel Mack. As nature shaped the wood, wild-wood builders use it in their furniture.Daniel Mack’s book is an entertain-ing introduction to the subject, frommaterials and tools to building instructions for various projects.165 pages, over 300 photographs and illustrations, some in colour, hardcover,215 x 215 mm, in German.No. 713464 24.21 € 25.90 €

GRÜNHOLZ-VORLAGENBUCHOver 300 ideas for traditional woodwork, by Ray Tabor. Gates, fences, tools for the home and garden, baskets and furniture – the wealth of knowledge in this book is virtually endless. Detailedtemplates and easy-to-understandinstructions make completing theprojects a pleasure. A source of inspiration, even for advanced learners. 240 pages, 320 b/w drawings, softcover, 190 x 245 mm, in German.No. 713765 27.94 € 29.90 €

GRÜNHOLZThe art of working with fresh wood,by Mike Abbott. An ancient methodrediscovered! The author explainsthe types of wood and their applica-tions when freshly cut. He also describes the tools required, theirhandling and care, and guides thereader through various projects.208 pages, 397 b/w illustrations,softcover, 200 x 280 mm,in German.No. 713476 20.56 € 22.00 €

SHOJI - DO-IT-YOURSELF SLIDING DOORS, DIVIDING WALLSMasterpieces of Japanese Craft Culture, by Toshio Odate. In thisbook, Toshio Odate explains how tomake a Japanese sliding door, fromlayout to gluing on the paper. Havingbeen trained himself as a tategushior sliding-door maker, in Japan, hegives insight into this traditional craft with great expertiseand explains the process compre-hensibly. 120 pages, 217 b/w photographs and 51 drawings, softcover, 210 x 280 mm

Carpentry, architecture

DAS HOLZBAU-BUCH (1909)By Adolf Opderbecke. Anyone who is interested in classical wood con-struction will find all the informationthey need in this reprint of a stan-dard work from 1909. The woodjoints, wall and roof structures,stairs and interior fittings are comprehensively explained in detailed drawings. 352 pages, 736 illustrations, 30 panels,hardcover, 220 x 285 mm, in German.No. 713402 29.91 € 32.00 €

DAS ZIMMERMANNSBUCH (1895)By Theodor Krauth and Franz Sales Meyer. This textbook has lost none of itstopicality since its first publicationin 1895. Even today, any carpenteror restorer interested in the traditional techniques would do well to consult it.From material scienceto decorative carving,all aspects of the carpenter´s craft are discussed in detail. 512 pages,131 panels,361 illustrations,hardcover,175 x 240 mm, in German.No. 713799 25.23 € 27.00 €

MÖBEL AUS WILDHOLZ

THE WORKSHOP BOOKBy Scott Landis. A Craftsman’s Guide to Making theMost of any Work Space. If you areplanning a workshop, this book willprove a valuable source of ideas andadvice. Based on the 20 samplefloor plans included, it shows youhow to make the best use of thespace you have available. The location of tool, wood and accessory storage areas, power tools,electrical sockets and dust collectors are all discussed in great detail. 216 pages,301 photographs and 76 drawings, softcover240 x 285 mm, in English.No. 713586 18.60 € 19.90 €

HOLZVERBINDUNGENBy Terrie Noll. »Holzverbindungen«(The Joint Book) provides clearlydescribed, easy-to-follow step-by-step instructions for making allkinds of basic wood joints and theirvariations. The well-explained over-view is complemented by useful in-formation on the required materialsand interesting aspects of furnituredesign. 144 pages, 700 colouredimages and drawings, hardcover,290 x 226 mm, in German.No. 713189 27.94 € 29.90 €

German No. 713249 29.91 € 32.00 €English No. 713470 18.60 € 19.90 €

No. 713253 27.94 € 29.90 €

No. 713360 23.36 € 25.00 €

No. 713197 27.94 € 29.90 €

Woodturning

GRUNDKURS DRECHSELNBy Keith Rowley. Even when turningwood, you should not have to learnfrom your mistakes. This is preciselythe purpose of this clearly formulatedand easy-understand standard work.Richly illustrated, it teaches the fun-damental craft and technical skillsand introduces the various projects. 180 pages, 275 photographsand 65 drawings, hardcover, 217 x 282 mm, in German.No. 713359 27.94 € 29.90 €

DAS DRECHSLERWERKBy Fritz Spannnagel. This reprint of a standard Germanwork first published in 1948 is anexcellent source of technical wood-turning information and hands-onpractical advice. It contains detaileddescriptions of numerous woodturn-ing tools, lathes, materials and surface-finishing techniques as wellas a history of the woodturning trade.320 pages, 1,250 b/w illustrations,hardcover, 175 x 240 mm, in German.No. 713575 34.39 € 36.80 €

Books || Carpentry, architecture, Woodturning, Finishing, restoration, Bow making

248

DRECHSELARBEITENBy Mark Baker. The English masterwoodturner presents 50 woodturningpieces of varying difficulty in thiswork, thus giving an overview of themain forms of woodturning. Preciseinstructions, tool lists, scale draw-ings, tips on techniques and tools,types of wood and surface treatmentmake the book a valuable guide.192 pages, numerous colour photo-graphs, hardcover, 217 x 282 mm,in German.No. 713156 27.94 € 29.90 €

GRÜNHOLZ DRECHSELNBy Michael O’Donnell. The fascinationof turning green wood starts whenyou first think about the nature oftrees. The book teaches this basicunderstanding and guides hobbyistsfrom cutting, selecting tools andtensioning right through to severalprojects. Clear photographs make iteasy to understand the process ofmaking transparent end-grain bowlsand cups. 134 pages, 207 photo-graphs and 85 drawings, softcover, 210 x 275 mm,in German.No. 713334 27.10 € 29.00 €

STIFTE DRECHSELNBy Kip Christensen and Rex Bur-ningham. The first book in Germanabout turning wooden fountain pens,rotating pencils and ballpoint pensintroduces the equipment and variedmaterials required, and describesthe processing of the metal parts in detail. Many clear photographs clarify the individual steps.166 pages, many colour illustrations,hardcover, 210 x 275 mm, in German.No. 713877 26.92 € 28.80 €

NEUES DRECHSELN - EIN ANLEITUNGSBUCH FÜR DEN EINSTIEGBy Helga Becker. This book delivers a completely modern approach to the classic craftof woodturning. It provides step-by-step descriptions of how to makeclear, modern designs from a woodblank. Each technique is so clearlyillustrated that even beginners caneasily comprehend all eighteen pro-jects presented. 160 pages, 600 colour photographs,hardcover, 235 x 260 mm, in German.No. 713165 37.29 € 39.90 €

Finishing, restoration

OBERFLÄCHENBEHANDLUNG VON HOLZClassic techniques and recipes fromSam Allen. Surface treatment notonly makes wood easy to care for, italso enhances its beauty. Sam Allenprovides all the comprehensive andvery practical traditional methods,such as French polishing, painting,oiling and waxing, grinding, picklingand varnishing. 128 pages, 165colour illustrations, hardcover210 x 255 mm, in German.No. 713739 29.91 € 32.00 €

BEHANDLUNG VON HOLZOBERFLÄCHENBy Derrick Crump. Nothing is more disappointing thana complex surface treatment whichdoesn’t have the desired result. Thisbook helps you avoid mistakes witha thorough introduction to the che-mistry of stains, paints, oils andwaxes and their correct use, as wellas surface preparation. 176 pages,over 300 illustrations, hardcover197 x 272 mm, in German.

NATURFARBEN HANDBUCHBy Lynn Edwards und Julia Lawless.The authors of this book have dugdeeply into nature’s bag of tricks tocome up with this collection of thebest natural paints and glazes forwalls and woodwork. The propertiesof various natural pigments, bindingagents and solvents are described,along with numerous recipes and finishing techniques. 190 pages,numerous colour illustrations, hardcover, 190 x 290 mm, in German.

INTARSIENTechniques and design step-by-step,by Jack Metcalfe and John Apps.This technical book promises aneasy introduction to the art of inlays.In addition to presenting a widerange of materials, tools and tech-niques, the path to completion is explained in twelve courses. Themany objects, with instructions onhow to make them yourself, give youideas for practising your newly acquired skills.176 pages, 386 colour illustrations, softcover,190 x 248 mm, in German.No. 713721 27.94 € 29.90 €

Bow making

BOGENSCHIESSEN - AUSRÜSTUNG, ZUBEHÖR,SELBST GEMACHTBy Volkmar Hübschmann. Archery is even more fun with customised equipment. Fourteen experts provide step-by-step instructions for making your ownequipment, accessories, quiver types, bow strings, arrows and targets.224 pages,560 colour,photographs,hardcover,215 x 275 mm,in German.No. 713844 37.20 € 39.80 €

THE COMPLETE JAPANESE JOINERYBy Hideo Sato and Yasua Nakahara.This classic book is a must for any-one wanting to learn how to makeJapanese wood joints. Starting withthe selection and preparation of thewood, it introduces and provides de-tailed drawings of over 100 straightand cross joints and explains theiruses. Also includes an introductionto using and sharpening Japanesetools. 397 pages, over 500 drawings,softcover, 185 x 230 mm, in English.No. 713587 23.27 € 24.90 €

THE COMPLETE ILLUSTRATED GUIDE TO JOINERY. By Gary Rogowski. All types of wood joints used inhandicrafts are presented in this reference work. The author explainstheir purpose and procedures formaking them using handheld tools.Novices and professionals alike willbenefit from the logical step-by-stepphotographs and descriptions.390 pages, over 1,700 photographsand drawings, hardcover, 240 x 282 mm,in English.No. 713761 27.94 € 29.90 €

BLOCKHÄUSER UND HÜTTEN SELBST GEBAUTBy Sven-Gunnar Håkansson. In this technical book, the Swedishauthor presents the fundamentalsof log construction. The design basics, wood selection, joints, insu-lation, roofing, wood coating and de-sign appropriate for the material are discussed in detail. Numerous examples, from sauna cabins to residential houses, are fully documented in photographs.338 pages, over 500 photographs and drawings, hardcover,175 x 245 mm,in German.No. 713213 34.49 € 36.90 €

See www.more-than-tools.defor more books on woodworking.

NEUE BAUMHÄUSER DER WELTBy Pete Nelson. For a long time tree houses were onlythe dreams of children. The cheaplymade constructions would barely lasta winter. The author, architect andcarpenter, who builds tree homes allover the world, proves once againthat living in the trees is not a dreamat all. 224 pages, several illustra-tions, hardcover, 202 x 295 mm, in German.

TRAUMHAFTE BAUMHÄUSER30 new and extraordinary designs in wood are presented in this book.The team around La Cabane Per-chée is becoming more and moreambitious and refined when itcomes to the constructions. Not asingle tree will have its grothinterrupted and no metal will harmthe bark. Superb pictures of the treehouses and their exclusive interiorsas well as spectacular views awaityou. This book is full of ideas and made for anyonewho longs for their childhood dream of a life up in thetrees. 124 pages, colour photographs and drawings onevery page, hardcover, 360 x 260 mm, in German.No. 713897 37.29 € 39.90 €

Books || Bow making, Boat building, Tools, Knives and sharpening

249

DAS BOGENBAUER-BUCHEuropean bow making from theStone Age to today. A group of ex-perts focuses on the history and de-sign of European longbows, andoffers beginners clear instructions,and advanced learners tips on se-lecting wood and adhesives, as wellas precise dimensions for makingthe different bow shapes yourself.236 pages, 127 b/w photographs,12 colour panels and many illustrations,hardcover, 215 x 275 mm, in German.No. 713349 27.85 € 29.80 €

DIE HORNBOGENARMBRUSTBy Holger Richter. Even today,crossbows impress us with theirpower and elegant shape. As muchof the knowledge of how to makethem has been lost, this volumeprovides valuable information in numerous detailed photos and de-sign drawings. The precise dimensions and many colour panelsare an excellent basis for making arealistic replica. 192 pages, manycolour illustrations, hardcover, 215 x 275 mm,in German.No. 713190 37.20 € 39.80 €

A THE TRADITIONAL BOWYER’S BIBLEThe Bowyer’s bible is without doubt the most compre-hensive and in-depth source of information for traditio-nal bow making.

1 Volume 1In volume 1, 7 expert authors writeabout the subjects of wood sourcingand storage, bow design, buildingyew and osage bows, Indian bows,connection techniques, strings andother backings, tillers and makinggrips and arrows. Fascinating rea-ding for all who hear the ancientcall of the bow. 360 pages, many illustrations, hardcover, 180 x 240 mm, in English.No. 713251 31.78 € 34.00 €

2 Volume 2The second volume of the bow-making bible gathers the combinedexpertise of 8 authors. They des-cribe the history of bow making and discuss American, European,composite and recurve bows. Otherarticles deal with bending, makingstrings, tips, quivers, improvingshooting techniques etc.318 pages, 347 b/w illustrations,hardcover, 180 x 240 mm,in English.No. 713128 31.78 € 34.00 €

See www.more-than-tools.defor more books on bow making.

3 Volume 3The third volume of the indispens-able standard work on classical bow making comprehensively covers tools, bows of the world, Korean, Indian, African, take-down and Stone Age bows, stone tips andwooden arrows. 360 pages, many illustrations, hardcover, 180 x 240 mm,in English.No. 713756 31.78 € 34.00 €

4 Volume 4In Volume 4, 11 bow experts document the quality the rediscov-ered art of making wooden bows has now reached. The subjects ofbow wood, heat treatment, powerand design, and laminated bows aredealt with in particular detail. Bothnovices and advanced learners willfind valuable tips on making highpowered bows. 416 pages, numerous b/w illustrations,hardcover, 180 x 240 mm, in German.No. 713524 31.78 € 34.00 €

Boat building

BOOTSBAU - PRAKTISCHER SCHIFFBAUBy A. Brix. This reprint from 1929shows the designs of a wide range ofsailing, rowing and motor boats, aswell as coastal, rescue, pilot and fishing vehicles in over 500 linedrawings. Practical texts and detail-ed drawings make the introductionto classical boat building easy to understand. Boat owners, modelbuilders and boat builders appre-ciate the »Brix« as a reliable guide.394 pages, 494 b/w drawings, numerous tables, hardcover, 170 x 244 mm,in German.

No. 713150 26.17 € 28.00 €

KAYAK CRAFTRib construction for top-quality kayaks, by Ted Moores. The dreamof building a perfect kayak cancome true. Ted Moores describes the construction of the Endeavour17 and three other kayaks with dimensions and designs. With pro-fessional tips and techniques fromthe boat-building pioneer, nothingstands in the way of a perfect result.188 pages, numerous b/w photographsand drawings, softcover, 220 x 278 mm,in German.No. 713147 32.71 € 35.00 €

CANOECRAFTThe art of building a canoe,by Ted Moores and MerilynMohr. This book explainsclearly how to build a canoewith your own hands. SevenNorth American boat typesare presented with their dimensions and designs.The procedure for buildingthem is explained in detail. 245 pages, numerous illustrations, softcover, 270 x 205 mm,in German.No. 713406 32.71 € 35.00 €

See www.more-than-tools.defor more books on boat building.

Tools

ARBEITSBUCH FEINSCHNITTSÄGEBy John A. Nelson. 25 projects,from basic to not-so-simple.This book provides a complete beginner’s course in using scrollsaws: A chapter on the history andan overview of modern scroll sawsare followed by simple exercises,which become progressively more difficult. 87 pages, numerous colourphotographs and illustrations, soft-cover, 210 x 280 mm, in German.No. 713762 18.60 € 19.90 €

JAPANESE WOODWORKING TOOLSBy Toshio Odate. Japanese saws andplanes have different designs anduses than western tools. ToshioOdate, a Japanese joiner and profes-sor of design, explains the tools andtheir use in detail, and describestechnical and historical aspects. Anindispensable reference work foranyone who wants to use Japanesetools properly. 189 pages, lavishly illustrated with b/w photographs and drawings, hardcover, 245 x 310 mm,in English.No. 713502 19.53 € 20.90 €

THE TOOLBOX BOOKA Craftsman’s Guide to Tool Chests,Cabinets and Storage Systems, byJim Tolpin. As well as fulfilling indispensable practical require-ments, toolboxes can also be aes-thetically pleasing woodworkmasterpieces in their own right. The author describes many types of tool storage systems, from thebasic toolbag to the exquisitely ornamented cabinet, and shows you how to make eachpiece in numerous sketches and vivid colour photo-graphs. 199 pages, 190 photographs, 100 detaileddrawings, softcover, 240 x 285 mm, in English.No. 713559 18.60 € 19.90 €

MESSER SCHÄRFEN WIE DIE PROFISBy Carsten Bothe. Knives need regular care and must be sharpenedcorrectly. This book introduces suit-able sharpening tools and explainsthe correct sharpening technique for each tool. It also explains thecorrect way to sharpen axes, scissorsand tools. Numerous tips by the aut-hor make sharpening a pleasure.112 pages, about 60 colour photographs, softcover, 158 x 213 mm, in German.No. 713167 7.94 € 8.50 €

Knives and sharpening

SCHWEDENMESSERMake your own handles and sheaths, by Bo Bergman. As well as having functional properties, the perfect all-roundknife must be to the personal tasteof the user. The best way to guarantee this is to make the knifeyourself. Bo Bergman shows you how to make your own personalised all-round tool.136 pages,244 illustrations,softcover,170 x 240 mm,in German.No. 713448 25.23 € 27.00 €

REFLEXBOGEN, GESCHICHTE UND HERSTELLUNGFor thousands of years, compositebows have represented the finestcraftsmanship and are no less fasci-nating today. However, the know-ledge of these bows had almostbeen forgotten. Here many famous authors and experienced bow makers have come together to gatherold and new information about techniques, forms, suitablematerials and tools from the StoneAge to our modern world. This book will not only showyou step by step everything you need to know aboutcomposite bows, but you will also be able to use this knowledge and the practical instructions to build yourown unique bow. 336 pages, numerous photos and illustrations in colour, hardcover, 275 x 215 mm,in German.No. 713611 44.86 € 48.00 €

THE TRADITIONAL BOWYER`S BIBLE (3-VOLUME SET)in English, see www.more-than-tools.de

No. 713774 27.94 € 29.90 €

No. 713163 20.56 € 22.00 €

HANDBUCH HOLZBIEGENBy Zachary Taylor. Whether you’re making frames, boatplanks, chair frames or oval boxes,bending wood is often like walking atightrope. This book increases your chances of success considerablywith many practical tips on selectingwood and material. As well as hot bending, laminate and notching techniques are discussed, as are tips on keeping shape.144 pages,213 illustrations,hardcover,204 x 254 mm,in German.No. 713114 39.25 € 42.00 €

DAS BUCH VOM STUHLGEFLECHTBy Bruce W. Miller and Jim Widess.This richly illustrated guidebook provides comprehensive informationon how to re-string wicker furniture.Whether made with reeds, wicker,Danish cord or other materials, theeasy-to-understand step-by-step instructions show howto turn old seats withbroken weaves intobeautiful centre-pieces again. The variety of traditional weavingtechniques presen-ted also allows historical furniturewith unusual pat-terns to be restored.144 pages, numerous illustrations,hardcover, 210 x 280 mm,in German.No. 713729 32.62 € 34.90 €

Books || Knives and sharpening, Forging, Traditional techniques

250

Traditional techniques

FEUERFrom the Stone Age to the burningglass. By Roland Müller. This booksystematically describes the theoryand practice of lighting fires withsimple equipment. It presents thewhole range of tools and materialsfor cinder, plant science, flints, firesticks, drills, right through to burning glasses. An interesting bookon a unique subject! 205 pages,116 colour photographs, numeroustables, hardcover, 175 x 245 mm,in German.No. 713137 23.36 € 25.00 €

MESSER SCHMIEDENA Norwegian art, by Håvard Berg-land. Explains all steps required tomake Scandinavian knives, designhandles, leather sheaths, ornamentation, as well as forging,hardening and polishing the blade.In particular in relation to forge-welding techniques, the most famous knifesmith in Norway givesinsights into methods many of hiscolleagues protect like secrets.168 pages, over 300 illustrations,hardcover, 173 x 245 mm, in German.No. 713399 29.91 € 32.00 €

DIE KUNST DES SCHMIEDENSThe big textbook of traditional techniques, by Håvard Bergland. This book shows you in detail how to forge knife blades, woodworking tools, fittings, locks and works of art in step-by-step drawings, photo-graphs of the objects and work situations, and includes chapters on material science. 344 pages, over 1,500 illustrations, hardcover,220 x 265 mm, in German.No. 713715 46.54 € 49.80 €

DER SCHMIED AM AMBOSSA practical workbook for all black-smiths, by Herrmann Hundehagen. In practical form, this introductorybook teaches all you need to knowabout hand-forging. In a modern format, it describes in detail the required tools and equipment, reshaping and welding techniques,and even includes heat treatment.An absolute must for every professional and hobby blacksmith!162 pages, 186 b/w illustrationsand photographs, hardcover, 152 x 220 mm,in German.No. 713305 25.23 € 27.00 €

MESSER SCHMIEDEN FÜR ANFÄNGERFrom the workshop series by Ernst G. Siebeneicher and JürgenRosinski. This practical manualgives a straightforward and good-value introduction to the fascinatinghobby of bladesmithing. With count-less step-by-step photos, it showsyou how to construct a simplesmith's hearth, how to make the necessary tools yourself, how to forge a stick-tangblade out of springsteel and make itinto a finished knife. 128 pages, numerouscolour photographs,softcover,170 x 230 mm, in German.No. 713796 27.85 € 29.80 €

See www.more-than-tools.de for more books on blacksmithing.

ALTE SCHMIEDEKUNST - DAMASZENERSTAHL,BAND 1By Heinz Denig. The author is regarded as the man who rediscovered Damascus forgingin Europe and is one of the outstanding experts in this field. His book is an essential reference work for anyone interested in folding, welding and torsion techniques. The different forging techniques and methods of model production are presented with a strong practical orientation.132 pages, 14 colour, 29 b/w photographs, 22 drawings, hardcover, 215 x 205 mm, in German.No. 713850 21.50 € 23.00 €

Forging

SCHMIEDEN LERNENBy Lars Enander and Karl-GunnarNorén. The authors introduce readers to the craft of blacksmithingin a conversational style, startingwith setting up a workshop andfoundry, tools and metal science.Techniques are practised in simpleand progressively more challengingprojects, right through to forge welding. Learn to make smithying tools, an axe head,and knife blades using laminated and damascene techniques, fittings and blacksmith art, among otheritems. 168 pages, approx. 300 illustrations, hardcover,210 x 240 mm, in German.No. 713232 25.05 € 26.80 €MESSERKLINGEN UND STAHL

Technological observations on knifeblades, by Roman Landes. With thisin-depth technical book on metall-urgy and factors affecting sharpnessand durability, Roman Landes shedslight on the mysteries of blade al-chemy. As well as types of steel,heat treatment and blade geometry,objective test methods and optimi-sation processes are discussed. A must for any ambitious knifemaker and collector. 176 pages,numerous diagrams and illustrations,hardcover, 160 x 230 mm, in German.No. 713166 37.20 € 39.80 €

KLEINES BREVIER VOM MESSERMACHENBy Bo Bergmann. In this compactbook, the master of Scandinavianknife making offers an ideal intro-duction to a wonderful hobby. However, even experienced knifemakers will find interesting informa-tion here on tools, materials, worktechniques and finishing. The docu-menting of different types of knivesmakes this book a valuable guide forevery knife maker. 112 pages,46 b/w drawings and 8 colour panels, hardcover, 130 x 205 mm,in German.

See www.more-than-tools.defor more books on knives and sharpening.

THE ART OF JAPANESE SWORD POLISHINGBy Setsuo Takaiwa, Yoshindo Yoshihara, Leon and Hiroko Kapp. No less important than forging is the polishing of a blade. It revealsthe character of the blade andbrings the steel to life. In this book,the pupils of »living national treasure« Matsuo Fujishiro guides usthrough the art of sword polishing.The book´s encyclopaedic documentation helps to understandthe processes. 192 pages, hardcover, 190 x 260 mm, in English.No. 713784 37.29 € 39.90 €

TAUNTON’S COMPLETE ILLUSTRATED GUIDE TO SHARPENINGBy Thomas Lie-Nielsen. Step-by-step instructions and abundant insider tips are providedfor sharpening all types of wood-working tools and knives. A discussion on types of steel and acomplete overview of all sharpeningtools and machines complete themost comprehensive and technicallyin-depth book on sharpening cur-rently available. 216 pages, over 750 colour photographs, numerous drawings, hardcover,240 x 285 mm, in English.

ALLES WAS SCHARF MACHTBy Egon Binder. This compact paperback is an introduction to sharpening all kinds of cutting implements. Practical sharpeningmethods for knives, woodworkingtools, scissors, chain saws and evenrazors are described. Chapters onsharpening implements and culturalarticles complete this brief guide tosharpening. 121 pages, 50 colourphotographs, softcover, 130 x 190 mm, in German.No. 713160 9.25 € 9.90 €

No. 713713 23.27 € 24.90 €

Books || Traditional techniques, Garden and kitchen

251

HANDBUCH LEDERARBEITENBy Valerie Michael. Introduction tothe fascinating world of leather craft-ing. The book presents materials,tools and basic techniques. 128 pages, 178 photographs,some in colour, hardcover,210 x 260 mm,in German.

No. 713130 36.36 € 38.90 €

LEDERBy Josephine Barbe. History, techniques, projects. This book provides important information onthe history of leather and introducestypes of leather and processing techniques. 25 projects, shoes,bags, cushions, jewellery and manymore items are described compre-hensibly with the degree of difficultyindicated. 176 pages, 247 colour pictures, 65 illustrations,hardcover, 240 x 266 mm, in German.No. 713826 37.29 € 39.90 €

SPIELE UND SPIELZEUG AUS HOLZ SELBST GEMACHTBy Willi Brokbals. This instruction book presents 12 classic games and 13 originaltoys with craft expertise. With cleardrawings, parts lists and descript-ions of steps, the projects are easy to understand, even for the less experienced. There is enough freedom to exercise your own creativity.159 pages,34 colour photographs,117 drawings, 27 tables,hardcover,195 x 264 mm,in German.

See www.more-than-tools.defor more books on traditional techniques.

Garden and Kitchen

MAUERN AUS NATURSTEINBy Volker Friedrich. This book gives an in-depth intro-duction into selecting the right material for building natural stonewalls, treating and processing it. The procedure for building walls is documented step-by-step, andjoints, seals and planting are discussedbased on numerous examples. Of course there are also sections ontools and materials, as well as exact instructions and invaluable practical tips. 167 pages,104 colour photo-graphs, 58 drawings,20 tables, hardcover,194 x 265 mm, in German.No. 713829 27.94 € 29.90 €

MAKING HEIRLOOM BOXESBy Peter Lloyd. Professional woodworker Peter Lloyd presents 11 exquisite boxes in solid wood that manage to be elegant, original and practical at thesame time. Each box is made from a single piece of hard-wood. No other materi-als are used, allowing the form ofthe wood and the individual design tospeak for themselves.169 pages,numerous photos and illustrations,softcover,213 x 275 mm,in English.No. 713265 14.86 € 15.90 €

FIVE HUNDRED AND SEVEN MECHANICAL MOVEMENTS

No. 713110 12.06 € 12.90 €

By Henry T. Brown. This small bookdates from the beginning of the Industrial Revolution and lists over500 moving contraptions made ofcogs, disks, levers, chains, strings,shafts and joints. An excellent initiation into the magical world ofmechanics, with many applicationsin making toys and practical devices. 122 pages, 507 illustrations, softcover, 150 x 225 mm, in English.

OBSTBÄUME SCHNEIDEN UND PFLEGENBy Jürg Maurer. A good pruning cut brings a good harvest. This well-illustrated guide will help you become a successful fruit-tree gardener, explaining what to look out for whenselecting breeds and when planting.Many drawings and photographsshow cutting techniques and abreed chart provides a good overview of recommendedbreeds.160 pages, 195 colour photographs, 60 drawings, 8 tables, softcover, 175 x 240 mm, in German.No. 713893 13.93 € 14.90 €

BESSER GÄRTNERN - PFLANZEN RICHTIG SCHNEIDENBy Colin Crosbie. The most important principles andproven techniques of plant cuttingare clearly presented in a successfulcombination of photo sequences andprecise texts. Expert tips, checklistsand a cutting calendar make thispractical book an ideal guidebookfor the hobby gardener.160 pages, over 500 colour photo-graphs, softcover, 184 x 235 mm,in German.No. 713872 9.30 € 9.95 €

WEIDENFLECHTWERKE - LEBENDIGE STRUKTUREN IM GARTENBy Marion Fröhlich and Hans-PeterSturm. Everything you need to knowabout harvesting, sorting, storingand weaving wicker, as taught bymaster weaver Peter Sturm. Thebook documents in detail how tomake wicker tunnels, tepees, growing bowers, climbing frames,woven fences and decorative ob-jects. An inspiring book for profess-ional and hobby weavers, teachersand all creative hobby gardeners.155 pages, 124 colour photographs and many illustrations, hardcover, 195 x 265 mm, in German.No. 713506 27.94 € 29.90 €

ANLEITUNG ZUM FLECHTEN MIT WEIDENBy Bernhard and Regula Verdet-Fierz. Wicker plants, their care, harvesting and processing to makepractical and aesthetic objects arecomprehensively presented in thisbook. Detailed drawings explain theindividual weaving procedures andmake getting started in weaving ea-sier. Includes projects suitable forboth novices and advanced craftworkers.361 pages, 450 b/w illustrations,softcover, 176 x 247 mm,in German.No. 713820 23.27 € 24.90 €

FUNDSTÜCKE SCHMUCKSTÜCKEBy Armin Minet. Inconspicuousknots, which grow on trees as part ofself-healing processes, are a sourceof fascination for the mineralogistand »woodsmith«, Armin Minet. He turns them into unique andbeautiful earrings, chains, brooches,pendants and decorations. This bookis more than just a guide to makingjewellery. 90 pages,numerous illustrations, hardcover170 x 240 mm, in German.No. 713789 20.56 € 22.00 €

OBSTGEHÖLZE ERZIEHEN UND SCHNEIDENBy Bernd Schulz and Gerd Groß-mann. This book, which explains thebasics of cutting, describes how totrain forms and explains the particu-larities of the individual fruit species.With detailed colour drawings andeasy-to-understand texts, the authorsdescribe professional tricks for fruit-tree cutting in the second edition oftheir book. This book is a must foranyone who has always wanted toknow more about the correct cultivation of fruit trees and shrubs.142 pages, colour photos and sketches throughout thebook, hardcover, 240 x 175 mm, in German. No. 713199 15.79 € 16.90 €

GEHÖLZE VON A-ZBy Andreas Bärtels. The comprehensive standard workon trees and shrubs provides at leastone page of compact knowledge oneach of the different species andtheir characteristics, including theirappearance, uses, habitat and culti-vation. This book helps you choosethe right trees and shrubs to formthe unique character of your garden and offers useful tips for the correct combination of plants.286 pages,coloured photosthroughout thebook, hardcover,270 x 200 mm,in German. No. 713200 27.94 € 29.90 €

TASCHENATLAS ZIERGEHÖLZE SCHNEIDENThis book by Helmut Pirc explainsthe basics you need from the growthof plants to the correct cutting oftrees and shrubs. The main part ofthe book is dedicated to 40 differentspecies of trees and shrubs, eachwith a double-page spread explain-ing the correct way and appropriatetime for cutting, including drawingsand description.128 pages, colourphotos and sketches through-out the book, softcover, 190 x 130 mm,in German.No. 713198 9.25 € 9.90 €

No. 713894 10.23 € 10.95 €

German No. 713736 10.84 € 12.90 €English No. 713753 10.84 € 12.90 €

Books || Garden and kitchen, DVDs, Instrument making

252

Instrument making

THE ART OF VIOLIN MAKINGBy Chris Johnson and Roy Courtnall.Anyone involved in the art of violinmaking will love this large-format reference book. It focuses on the individual steps professionals use in violin making. The accompanyingdrawings, detail photographs and descriptions make the violin-makingprocess easy for amateurs to under-stand. A presentation of great pastand present makers with their instru-ments, glossary, trade directory and notes on various instrument collections complete this unique book. 253 pages, over 400 photographs and illustrations,some in colour, hardcover, 220 x 305 mm, in English.No. 713445 92.52 € 99.00 €

MAKING MASTER GUITARSBy Roy Courtnall. A craftsman’sguide to the exciting and challeng-ing pursuit of making classical guit-ars. Part one of the book containschapters on nine famous makers andserves as a unique record of the diff-erent methods that have evolvedsince Antonio de Torres first definedthe essential characteristics of themodern classical guitar in the1850’s. A set of detailed drawingsof one of each maker’s guitars isalso provided. Parts two and three provide practical in-formation on the selection of tools, workshop setup and step-by-step instructions on guitar construction, illustrated by numerous photographs and drawings. 330 pages, numerous b/w photographs and sketches,hardcover, 220 x 305 mm, in English.No. 713394 74.67 € 79.90 €

VIOLIN MAKER'S NOTEBOOK

No. 713367 21.40 € 22.90 €

A Companion Volume to: UsefulMeasurements for Violin Makers. By Henry A. Strobel. This indispens-able shop manual treats several topics not covered in Strobel's stan-dard violin-making books, includingbow rehairing and repairs, varnishand crack repairs, photographing instruments and even some music theory for the instrument maker. The book concludes with a step-by-step repair of a badly damaged master violin.74 pages, numerous b/w photos, diagrams and tables,softcover, 218 x 279 mm, in English.

GITARRENBAUAccording to Martin Koch, »the secret of guitar making is patience«. In this book, he patiently guides theamateur guitar maker through all thesteps of making an acoustic guitar,from selecting the correct wood tousing the proper finishing tech-niques. He provides photos for mostof the steps as well as numeroushelpful diagrams, making his instructions easy for guitar makersof all levels to follow. 135 pages, numerous sketches and diagrams, softcover, 190 x 270 mm, in German.No. 713372 25.70 € 27.50 €

MAKING AN ARCHTOP GUITARBy Robert Benedetto. At the age of12, Robert Benedetto discovered hisgrandfather's tool chest and promptlyused the tools he found to carve asmall knife. Shortly after, he craftedhis first guitar using scraps of woodhe found in the workshop. Over the26 years since, he has establishedhimself as one of the world's prem-iere archtop-guitar makers. In thisbook, he shares his art with the wider community forthe first time. Step-by-step instructions for building anarchtop guitar are provided alongside helpful photosand additional tips on tool selection and use. A uniqueresource for guitar makers, violin makers and guitarplayers alike. 276 pages, softcover, 215 x 280 mm, in English.No. 713342 46.64 € 49.90 €

GEIGENBAUSCHULE MITTENWALD 1977-1981By Andreas Zimmermann. This book contains reproductions of the handwritten notes taken bymaster violinmaker Andreas Zimmer-mann while attending the violin-making school in Mittenwald, Ger-many. The notes contain step-by-step descriptions of how to make a violin, from the initial marking of the wood to the final application of the strings. The final section ofZimmermann's notes details varnishing techniques andthe properties of various resins and dyes as well as im-portant techniques for repairing stringed instrumentsand bows. Numerous precisely drawn sketches give the reader a clearer picture of many steps of the techniques described.354 pages, 87 b/w drawings, softcover, 160 x 225 mm, in German.No. 713733 27.10 € 29.00 €

SAITENINSTRUMENTE SELBST BAUENMaking a stringed instrument presents a special woodworkingchallenge which should only be attempted with the help of detailedinstructions. In this book, GeorgeBuchanan describes the fundamen-tals of making stringed instruments(violins, cellos, man-dolins and stylish jazzguitars), from select-ing the proper woodand carving tech-niques to the finalassembly. Over 300 drawingsand countless prac-tical tips allow beginner instrument makersto master this difficult art. 212 pages, over500 illustrations, hardcover,195 x 268 mm, in German.No. 713725 39.25 € 42.00 €

EINFACH MÄHEN MIT DER SENSEBy Bernhard Lehnert. Scything is becoming more andmore popular. For anyone who haslearned the skill, scything is a relax-ing exercise in fresh air. The author provides hints and tips on the rightchoice of scythe and the right tech-nique, using many illustrations.Peening and whetting are also de-scribed. 133 illustrations, softcover146 x 210 mm, in German.

See www.more-than-tools.de for more books on gardens and plants.

DVDs

INTRODUCTION TO FRENCH POLISHINGIn this training film, expert Peter Zehmisch shares with us his know-ledge of the finest form of surfacetreatment, which he has acquiredover many years. He explains thematerials and the individual operations (priming, basic polishing,cover polishing, polishing out scratches, and fine polishing).DVD, 21 min.

SCYTHING TECHNIQUESIn this introduction, master scytherErnst Schoiswohl and Canadian organic farmer Peter Vido teach usknowledge which has been virtuallyforgotten. From adjusting the snath,to the body position when mowing,to peening and honing the blade,viewers will learn everything theyneed to know about working with scythes.DVD, 20 min.

DAS SCHÄRFEN JAPANISCHER MESSERA Japanese master blacksmith with a legendary reputation in Japanshows you how to professionallysharpen kitchen knives on waterstones. He introduces different types of whetstone, shows the correct sharpening motions for sharpening single- and double-bevelled knives and provides information on caring forknives. Knives sharpened in this way not only makeyour work easier but are also a pleasure to use andallow you to treat your food with respect.DVD 15 minutes, in German.No. 713806 4.96 € 5.90 €

VIER FILME ÜBER UNTERSCHIED-LICHE HANDWERSTECHNIKENAUF EINER DVDFour films (Tools, Joints, Sharpening and Shoji) on one disk. Not suitable for NTSC players.

DVD, 135 minutes, in German.Also available as a set:Book and DVD. Page 247.

No. 713709 10.84 € 12.90 €

GRÜNHOLZ DRECHSELNIn this film, Scottish master wood turner Michael O´Donnell shows step by step how small works of art can be created on a turning lathe using freshly felled (green) wood. In six extraordinary projects, O’Donnell demonstrates how vessels can be made from end-grain and cross-grain wood with wafer-thin, translucent walls, some with natural edges.DVD, 80 min. in German.No. 713861 25.04 € 29.80 €

German No. 713734 7.48 € 8.90 € English No. 713752 7.48 € 8.90 €

SUSHIHisayuki Takeuchi cultivates the artof Sushi at the highest level. Come and learn from the master 80variations of sushi in 20 themedcompositions. Follow his techniquestep by step with precise instruct-ions and over 1,300 photos - fromthe basic composition of taste tofine-tuning the flavours. HisayukiTakeuchi was chef de cuisine inTokyo before opening a sushi restaurant in Paris in 1999. He later founded a sushi school.279 pages, many colour photographs, hardcover290 x 230 mm, in German.No. 713208 37.29 € 39.90 €

RINDE, DIE WUNDERWELT DER BÄUME ENTDECKENBy Cédric Pollet. With spectacularclose-up photos, this book showcases the superb textures and colours of bark, the life substance of trees. Nature photographer Pollet takes you on a tour of Europe, Africa, Asia, Oceania and America and shows you photographs from ten years of tireless searching for the mostbeautiful tree barks in the world.Some photographs seem almost surreal, which showsus once again that nature - as practical as it may seem- creates the true works of art.191 pages, many colour photographs, hardcover335 x 255 mm, in German.No. 713209 37.29 € 39.90 €

See www.more-than-tools.de for more books on instrument making.

Index

253

Aberl forest hatchet 59Aberl mallet axe 59Aberl Werdenfelser forest axe 59Abrasives and polishing materials 163,164 Abrasives 163Aburatsubo 93Accessories for metal planes 76 Accessory kit 91 Adapter bushing 108 Adapter for square bench dogs 152 Adzes 55,56 Akagashi saws 19 Alkanet root 168 All purpose hatchet 62,98 All purpose rabbet plane 75 All-metal chisel 36 Allongee gouges 44 All-purpose hatchets 62All-purpose knives 189 All-purpose sharpener 89 Aluminium folding saw 22,235Aluminium rule 160 American-style claw hammer 98 Anant®-plane 75 Angle drill head 141 Anti-corrosion coating 93 Anti-slip blocks 88 Anti-slip mat 88 Arata hocho 197 Arkansas oilstones 87 Arnaud draw knife 54 Arno gardening shears 232 Arts and crafts 241ff. Auger bit 142 Auger gimlets 143 Australian precious wood 175 Awl handle 158 Axes 57ff. Azebiki saw 18

Back saws Hanidwork 24 Back Saws 24 Backpack, reindeer leather 244 Ballistol® impregnation spray 160 Ballistol® 93 Balsam oil of turpentine 167 Bamboo backings 176 Bamboo vinegar 202 Banksia cones 176 Bark scraper 59 Bead forming tool 104 Beading tool 71 Beaver deep hollowing tool 104 Beeswax granulate 167 Belgian bench stones 87 Bench dogs 152 Bench Plane 79 Bench planes 70,73,75 Bench support 151 Bench vise 152,153 Bend-A-Light® mini 131 Benzoin 168 Bessey®-clamps 134-136 Bessey®-cutter 132 Bevel edge rule 129 Bevel gauge for tool edges 94 Bevel knife for leather 158 Bevel setter 129 Big Boy folding saw 22,235 Birch wood 175 Bird folding knife 213

Bit adapter for ratchet screwdriver 146 Bit chucking heads 142 Bit sets 142 Black walnuts 176 Blacksmith’s anvil 97 Blacksmithing hammer 97,98 Blade blank, full tang 216 Blade blanks 215,216 Blades 215,216 Block planes 68,72-79 Block rasp 115 Blue belgian stones 87 Blue Paper Steel 180 BMI®-spirit level 130 Boat glue 169 Bocote 174 Body clamps 136 Bog oak 175 Mopane 174 Bone glue 170 Bone plates 179 Bonsai tools 234 Books 245ff. Bowl finishing scraper 103 Bowl 203 Bowl gouge 103 Bowmaker’s scraping plane 79 Boxwood 173 Boxwood shears 231,233 Brace 141 Brad point drills 142 Branch and root shears 233 Branch shears 230-232 Brass mallet 49 Brass plumb 130 Brass rivets 99 Bread knife 198 Broad axes 63,64 Brush 168 Pincers 131 Brusletto® knife blade 216 Brusletto® outdoor knife Rognald 210 Bruyere wood 173 Buffalo horn 167 Buffing wheel 92 Burnisher 92

Cabinet make multi purpose folding saw 21 Cabinet scraper 74 Calliper 110,124 Camel bones 179 Camellia oil 93 Cap 156 Captive ring tool 104 CarBee®-pocket sharpener 89 Carbon-steel blades 216 Carnauba wax 167Carpenter’s axe 63 Carpenter’s axe 63 Carpenter’s chisel set 36 Carpenter’s hammer 96 Carpenter’s square 126,127 Carpenter’s try square 127 Carver‘s jig 108,152,153 Carver‘s vise 152,153 Carver’s mallets 49,97 Carver's bench plan 151 Carvers jig clamp unit 108 Carving and sculpting tools 39, 42-48 Carving blades 47 Carving blades, chin. 47-48

Carving blades, europ. 42-46 Carving gouge set 45,47 Carving knives 49 ff. Carving set 47 Case 243 Cast iron teapot 203 Cast iron trivet 203 Catfish leather 177 C-clamps 134 Cedarwood knife handle 176 Centre finder 110 Ceramic sharpening stone 86 Ceramic peeler 201Cerax®-super stones 86Chainsaw file 89 Pine tar oil 167 Chalk for chalk line 125 Chamfer plane 77 Chatter tool 104 Checkering file 118 Cheese grater 201 Children’s carving knife 53Children’s carving tool 50Chinese ball 104 Chinese carving knives 47,48 Chinese chisels 37 Chinese scissors 224,234 Chip carving knives 49,52 Chisel plane 69 Chisels 29 ff. Chisels, western 36 Chromium steel blades 216 Chucks 109 Chu-Gata nomi 31Circle cutter 146Circular plane 74 Clamp fixtures 137, 138 Clamps for floor layers 138 Clamps 133ff.Classic-pruning saw 236 Cleaning and polishing fabric 164 Cleaning stone 87 Cleaver knife 198 Coarse shaping stone 85, 91 Cocobolo 174Combination pliers 147,148Duo Sharp Whetstones 88 Combination square 128 Combination stones 85 Compact Saws 12,13,15-17Compact gouge set 46 Compass heads 126 Compass plane 77 Compass Saw 25 Compasses 110,126 Compact knives 189Cone cutter 144,145 Cones 176 Conical stones 86 Coping saws 25 Cork sanding belts 163 Corner chisel 37 Corner hammer 97 Cotton apron 156, 240 Cotton tool rolls 38 Countersink 144 Countersink drill 144 Cow hide 177 Cow horn plates 178 Cow horn 178 Craft knife 132 Cranked paring chisels 33

Crosshole countersink 144 Crossing files 113,116 Crown® turning tools 103ff. Curved adze 55 Cut-resistant gloves 156 Cutter 132Cutter saw 21Cutting and chopping board 200 Cutting board 200 Cutting pad 160 Cutting ruler 122

Damascus blade blanks 216 Damascus flat steel 180 Damascus hammer 96 Damascus hybrid chisels 35 Danish double bearded axe 63Deluxe saws 18Detail knife 50 Dial calliper 124 Diamond honing cones 89 Diamond needle file 118 Diamond saw 25 Diamond saw file 28 DICK- series Klassik 194 DICK-cap 156 Disc grinding machine 163 DMT-sharpening system 94 DMT-diamond stones 88-89 Dogleg chisel 43 Double bitted logging axe 59 Double bitted throwing axe 62 Double hoe 227 Double jaw honing jig 94 Double-bitted mortise axe 64 Douk-Douk 212 Dovetail chisels 33 Dovetail cutter 79 Dovetail gauge 128 Dovetail jaws 109 Dovetail plane 79 Dovetail scraper 103 Dovetail square 128 Dozuki-saws 12,13,17- 21 Dragon gouge 43 Dragon’s blood 168 Drawknife 54 Workwear 110 Drill chuck 108 Drill chucking tools 141 Drill stand 141 Drill stops 142 Ink line 125 Drills 139ff. Driver 100 Puzzle box 242 Tung oil 166 Heavy Duty I-beam bar clamp 137,138 DVDs 252

E.C.E® planes 79 Ebony 174 Edge clamp device 134 Edge clamp 134 Edge plane 79,158 Edge square 129 Elk leather 177 Ellsworth gouges 103 Emery cloth 163 End buttons 176 English sliding bevels 129 Epoxid glue 169

Index

254

Estwing®-hammers 98 European wood 173 European carving knives 42 Exotic wood 174 Extra wide chisel 34

Fabric band 176 Fabric scissors 224 Faceplate segments 110 Faceplate 108 Farming sickle 239 Felling axes 59 Felling und splitting wedge 61 Felt buffing wheel 92 File cleaner 120 File handles 120 File rasps 115 Files for knife maker’s 118 Files Glardon/Vallorbe 116-117 Files 111ff. Finger protectors 156 Finishing 161ff. Fire stick 210 Fisherman’s knife 208,209 Fishtail gouges 44 Flat adze 55 Flat files 116 Flat gouges 42-46 Flat jaws 110 Flat rasps 114 Flat-round pliers 147 Flex Light® 131 Flexible rule 122 Flexible shaft 142 Flexible shaft 165 Flooring clamp 138 Flot 78 Flower scoop 229 Flush cutting saws 24 Folding bone 158,160 Folding knife kits 210-214,217 Folding knife 210-214 Folding rule 123 Folding saws 21,23,22,27,235Folding square 127 Forest axes 59 Forstner bits 143 Frame saws 23 Fret saw 18 Frost® blades 216 Frost® knives 53

Garden claws 227,228 Garden fork 229 Garden knife 230 Garden shears 230 Garden tools 225ff.Gardening accessories 240Gardening apron 240 Gardening claw 228 Gardening gloves 240 Gardening hatchets 61 Gardening hoes 227 Gardening sets 240 Gardening shears 232 Genno 96 Glass cutter 132 Glossary of steel terms 218 Glue brushes 170 Glue container 170Glue for shoji paper 160 Glue injectores 169

Glue scrapers 80 Glue 169 Goldfield burls 176 Gorilla Clamps® 136 Gotland axe 63Gouges 103 Gouges 42,46,47 Gradometer 130 Grafting knife 230 Grafting knife 230 Gränsfors drawknife 54 Gränsfors® hatchets and axes 59,60,62 Gränsfors® sharpening stone 64 Grass sickle 239 Grasstree roots 176 Grenadill- Wood 174 Grill pan 204 Grinding aid 163 Grinding block 163 Grinding discs for wood 163

Habilis files 117Hager® lathe 107 Hair cutting scissors 224 Haircutting scissors 224 Half– round files 116 Halfmoon knife 158 Hammer hatchet 64 Hammers 95ff. Hand saw 23 Hand drill 141Hand grinder NT 119 Hand weeder 228 Handle head plates 180 Handles for Japanese kitchen knives 176 Hans-Karlsson-carving knives 53 Hard material saw 27 Hardwood plane 76 Harvest shears 231Harvesting sickles 239 Hatagane 136 Hatches and axes 57ff. Hattori® carpenter’s set 34 Hattori®- chisels 32,33 Hattori®-slicks 35 Hattori® turning tools 106 Hattori®-Kataba 14 Hayashi hocho 187 Hearing protector 110 Hedge shears 233Hegner- scroll saw 28 Hegner®- grinding machine 163 Hemp string 240 Herdim® precision rasps 112,113 Herdim®-HSS-blades 50 Herdim®-repair clamps 135 Hex shank twist drill 143 Hide glue 170 Higonokami- pocket knife 211 Hinge compass 126 Holdfast clamp 152 Hole punches set 159 Hollowers 104,105 Hollowing tools 104 Hon Dozuki 18 Horn 178 Hone 89 Honing oil 87 Honing stones 85-87Honing wheels 90, 91 Hoof rasp file 114 Hook tool 105

Hook turning tool 104 Hook 228 Horn products, arts and crafts 243 Horn squares 178 Horn tip 218 Hornbeam mallet 49 Hornhammer 218 Hornstrips 178Horse hair 179 Hot setting adhesives 170 Household scissors 224 HSS chisels 32,34HSS-blades 50HSS-turning tool set 106 Hunter’s hatchet 62 Hunting knives 205ff. Hybrid-chisels 35

Illuminated magnifying glass 131 Inden-Ya-Pouch 244Indian trade axes 62 Indoor gardening set 234 Ink 125 Inshave Tragskav 53 Inside caliper 110 Inspection tools 131 Insulation cutter 27 Isinglass glue 170

Japanes saw bag 20 Japanese shears 223 Japanese saws 7ff. Japanese sword steel 180 Japanese waterstones 85ff. Japanese blade blanks 215 Japanese carving tools 47 Japanese chisels 31ff. Japanese clamps 136 Japanese garden hatchet 61 Japanese hammers 96-97 Japanese hatchet 62 Japanese knife sets 190 Japanese knives 181ff. Japanese planes 76ff. Japanese razors 222 Japanese shoes 156 Japanese socks 156,240 Japanese splitting axes 60 Japanese working clothes 156 Jaws 109 Jigs 90,91,94 Jigs for Tormek 90 Jointer plane 71,73 Jointer/edger 80

Kangaroo leather 177 Kanna 76ff. Kataba saws 14,15,17,18,21,24Katana Boy folding saw 236 Katsuhiro hocho 192,193 Kelton™ turning tools 105 Kenryu- pruning saws 236 Kindling splitter 60 Kirjes® oil wax 167 Kirjes® oil wax 167 Kirjes®- sharpening system 165 Kitchen folding knives 198 Kitchen grater 201 Kitchen knife blade blanks 215 Kitchen shears 202 Kitchen utensils 199ff.Klemmsia® wooden clamps 136

Kliklamp 135 Knife blades 215,216 Knife blocks 199 Knife for salami and baguette 198 Knife kits 217 Knife pendant 212 Knife rests 199 Knives 181 ff. Knot repair set 144 Kobayashi hocho 185,187 Kobiki saws 18,236,237 Kogatana-marking knives 132 Kovax®- Emery cloth 163 Kugihiki-Saw 24 Kumo hocho 192 Kunz® planes 74 Kuro Ochi hocho 188 Kusakichi hocho 196

Laguiole folding knives 213Laminates 175 Lathe spindle replicator 108 Lathes and accessories 107,108 Leaf-rake 229 Leather dressing 160 Leather apron 156 Leather balm Equifix® 160 Leather bevel knife 158 Leather block plane case 76 Leather care products 160 Leather case for hedge shears 233 Leather case for pruning shears 231 Leather case for razors 221 Leather case for saws 20 Leather case for scrapers 80Leather cream 160 Leather for knife sheaths 177 Leather hammer 99 Leather knife 158 Leather oil 160 Leather plane 158 Leather products, arts and crafts 244 Leather protective caps 38 Leather scissors 158 Leather splitting system 159Leather strip 177 Leather tool roll 38 Leather tool roll for folding knives 214 Leather tool roll for razors 221 Leather tool roll for turning tools 106 Leather working tools 157ff. Leather 177 Leather-drill punch 159 Lever clamp 135,151 Lie-Nielsen planes 68-71 Lignea® chinese tung oil 166 Linden bast glue brush 170 Lindenmasur 175 Lindenwood 173 Line spirit level 130 Linen thread 158 Linol carving knife 51 Linseed oil Linolja® 166 Liquid ink 125 Litre glue pot 170 Locksmith’s hammer 98 Log dog 64 Log scribe 126 Hollow punch set 159 Long handled gouges 48Long handled hybrid chisels 35Long prong rake 228

Index

255

Longboy pruning saw 237 Low angle plane 69,72

Machete 239 Magnetic pickup 131 Magnetic tool bar 156 Magnifying lens 131 Magnolia knife handles 176 Malleable cast iron screw clamps 133 ff. Mallet axe 59 Mammoth handle scales 179Mammoth teeth 179 Manicure set 244 Maple wood 175 Marking chalk 125 Marking gauge 125 Marking heads 126 Marking knives 132 Maschine cut rasps 114 Masur birch 173Mat cutter 160 Materials 171 ff. Matsuba hocho 189 Matsune hocho 195 Mcusta®-folding knife 210 Measuring instruments 110,121 ff. Measuring tape 123 Measuring tools 126,127 Multi purpose twist drill 143 Metal drill 142 Metal file 116-118Metal objects, arts and crafts 243 Metal saws 27 Micro-Gloss®-Polish 164 Micro-Mesh® 164 Micrometer 124 Microplane® 4-sided box grater 201 Microplane® kitchen rasp 201 Mikisyo 48 Mill saw file 118Milling drill bit 143 Mini anvil 97 Mini folding saw 22Mini hammers 97 Mini hatchets 62 Mini- marking gauge 125 Mini one hand clamp 135 Mini planes 68,77,78 Mini sliding bevel 129 Mini spirit level 130 Mini square 127 Mini carpenters’ square 127 Mini chisels 36,37,50,52 Mini clamps 134 Mini saws 24Spurs 108 Mitre clamps 137 Mitre angle gauge 124 Mitre gauge 124,127 Mitre guide 124 Mitre plane 70 Mitre saw 26 Mitre square 128 Mitre trimmer 153 Mock ivory 179 Moisture meter 130Mokume Nomi 31 Trough-makers-adzes 56 Mono steels 180 Mora-blades 216 Mortars 204Mortise chisels 34

Mosaic pins 108 Mother-of-pearl 179 MTC®-pliers 147 Mulit-angle vise 153 Multi layer steel 180 Multi purpose file 119 Multi purpose knife 53,198 Multi saw 237Multi-clip 138 Multiform stone 86,87

Nagura 87 Nail pullers and bars 100Nail starter 100 Nails 99 Nano One- mini chisels 52 Nata Azumagata 61 Nata Jigata 61Natural sharpenning stones 87 Needle pliers 147 Needles files 117 Nigiri 223Nose scraper 103 Nuts 176

Obsidian 218Obsidian-knife 218 Octagonal-headed hammer 96 Oil pot 93 Oil 166-167 Oire Nomi 31,32 Olivewood 173 One hand pruning shears 230-232 One-hand clamps 135 One-hand curved adze 56 One-hand flat adze 55 One-hand Yariganna 48 Oneway®-accesoires 108,109 Oneway®-wood turning lathe 107 Orange oil 167 Orikomi-folding saws 22,235 Ornamental punches 159 Ostrich sinew 179 Outdoor axes 62 Outdoor blades 216 Outdoor hunting knife 205 ff. Outdoor knives 205 ff. Outdoor knife kits 217 Outdoor sets 210 Oyakata folding saw 21,22,235

Pakka wood 175 Palisander 174 Palm gouges 51,52 Palm wood 174,175 Pan 204 Pantograph 126 Paper cutter 160 Paper knife 243 Paper micarta 175 Paperstone 175 Parallel clamps 136 Parallel marker 126 Parallel vise 153 Parquet clamp 138 Parting tools 103Peeler 53,201 Peening anvil 238 Peening hammer 238Peening jig 238 Pfeil®-carving knives 49,50 Pfeil®-chisels 36

Pfeil®-draw knife 54 Pfeil®-gouges 42 Pfeil®-linoleum gouge 51 Pfeil®-scorp gouge 48 Pfeil®-sculptor’s gouges 44,45,46 Pfeil®-shoulder knife 50 Pfeil®-paring chisels 36 Pfeil®-woodcarving gouge 51 Piano wire cutters 148 Picard® hammer 98 Pickups 131 Pink Ivory 174 Pinking shears 224 Pipe cutter 240 Pipe pliers 148 Plane handles 76 Planes 65ff. Planting cone 229 Planting hoe 227 Planting towel 229 Plastic saw 27 Pliers 147-148 Plow plane 75 Plug cutter 144Pocket caliper 124 Pocket knife 211,212 Pocket plane 68,72,74 Pocket sharpener 89 Pocket Boy folding saw 22,235 Point.2.point 126 Polish and whetting paste 92 Polishing brush sleeves for sander 165 Polishing fabric 164 Polishing file 164 Polishing motor 165 Polishing paste 92,222 Polishing powder 92 Polishing sleeves 165 Pony® clamp fixtures 137 Poppy seed oil 166 Poultry shears 202 Powder and pigments 168 Power clamps 136 Power clamps 136 Power drill bits 142 Precision bench vise 152 Precision bevel edge ruler 129 Precision drill 141 Precision knife edge square 129 Precision rule 122 Precision sliding bevels 129 Precision sliding calliper 124 Precision sliding marker 125 Precision try square 127 Profile gauges 129 Prong-hoe 227 PRO-PM tools 103 PRO-PM-Turning tool set 106 Propolis chunks 167 Protective goggles 110 Protective guard for saw blades 20 Protective jaws 153 Protractor 124 Pruning knife 230,239 Pruning saws 235-237 Pruning saws 235,236, 237Puching pliers 158Pull pliers 147 Pumice powder 168 Punch awl 100 Punch set 125

Quick-sharpeners 89Quick-change saws 19

Rabbet block plane 73,74 Rabbit Skin Glue 170 Rabett plane 68,69,73,75,78,79 Radius plane 77,78 Rake 229 Ram’s horn scale 178 Ram’s horn 178 Edging knife 227 Rasp 115 Rasps handcut 112 Rasps milled 115 Rasps 111ff. Ratchet screwdriver 146 Rattan wrapping 176 Rawhide hammer 99 Razor 219ff. Reaming awl 100 Red deer horn 178 Red deer leather 177 Reform smoothing plane 79 Reindeer leather pouch 244 Repair clamps 135 Replacement wedges 64 Resins 168 Retriever 131 Rice jar 204 Strap cutter 159 Riffler 113,114 Ring tool 104 Rivets 99 Rock pick 98 Rocker knife 189,204 Rod cutter 145Roll mortar 204 Roller balls 156 Roofing hammer 98 Root hook 228 Roots 176 Rose bed fork 229 Rose shears 231 Rotating plate 153 Roughing out gouge 103 Round files 117 Rounding plane 145 Router bit set 114 Router plane 70,79 Rozsutec sharpening stone 87 Rubber boots 240 Rubber mallet 49 Rubber mallets 99 Rule stop 122 Rules 122 Rust eraser 93 Rust remover 93 Rust-prevention oil 93 Ryoba saws 16,17,18,24

Saddle soap 160 Safety splitting wedge 61 Saku hocho 190 Salad servers, horn 243 Salmon leather 177Salt and pepper shaker 243 Sanding kit 165 Sanding system 165 Saw and tool cases 20 Saw blade for scroll saw 28 Saw cases 20 Saw file 28

Index

256

Saw guide 26 Saw guide set 26 Saw rasp 115 Saw set pliers 28 Saw sets 17 Saws 7ff. Scalpel 132 Schröckenfux® scythes 238 Schwertfisch® rasps 113,114 Scissors 223,224 Scorp gouge 48 Scraper 103 Scraper 80,105 Scraper holder 80 Scraper plane 72 Scraper sharpening steel 80 Scraper steel 80 Scrapers 80 Scraping plane 71,74,77 Scraping plane 78 Screw removing pliers 148 Screw tap 146 Scribing tools 125 Scroll saw 28 Sculpting hatchet Täljyxa 54 Sculpting tools 39ff.Sculptor´s gouges compact 46 Sculptor´s tools 39ff. Sculptor’s axes 54 Sculptor’s gouge blades 47 Sculptor’s gouges 43,45,46,47 Scythes 238 Scythes 238 Semifinsished products 180 Sewing holster 158 Sewing scissors 224Shaker knobs 176 Shaker nails 99 Shapton® sharpening stone 86 Sharpener 145 Sharpening accessories 92,93 Sharpening stone accessories 88 Sharpening card 89 Sharpening device for knives 94 Sharpening device for plane blades 94 Sharpening paste 222 Sharpening sets 89 Sharpening stone for axes 64 Sharpening stone for Tormek 91 Sharpening stone holder 86, 88 Sharpening stones 85, 87 Sharpening system 90, 91, 92 Sharpening tools 81ff. Shaving block 222 Shaving brush 222 Shaving soap 222 Shaving soap dish 222 Sheap shears 232 Sheep leather rhubarb-tanned 177 Sheet metal shears 148 Shellac 168 Shigefusa hocho 186 Shigeki hocho 186,197 Shinko® sharpening system 92 Shoe hammer 159 Shoemaker’s rasp 114 Shoji paper 179 Shoulder knife 50 Shovels 229 Sickle 239 Sickle cleaver 61,239 Sickle hoe 228,239

Sickle iron 48 Sideaxe 61 Silicon carbide powder 92 Sinensis® 166 Sinensis® camellia oil 93,166Skew block plane 68 Skew chisels 37 Skew chisels 103 Slicer 201 Slick 35,64 Sliding bevels 129 Sliding square 127 Slipstones 87 Smoothing plane 74,77,79Smoothing plane 70,71,73,75,76 Snake wood 174 Snath 238 Soft face mallet 99 Soft touch plier 148 Solid steel bar clamps 133ff. Sommelier knife 202 Spade 229 Spear planes 48 Special knives 198 Spigot jaws 109,110 Spirit lamp 170 Spirit level 130 Splitting axe 60 Splitting knife 64 Splitting Maul 60 Splitting wedge 61 Spokeshave 72,74,78,79 Spoon gouge 53 Spreader clamps® 135 Spring clamp 136 Spring mitre bracket set 137 Square 126 Square gauge 127 Square head hammer 96 Square mallet 97 Srew driver 140,141,146 Stabilized wood 175Stag horn crown pieces 178 Stanley chalk line 125 Stanley® planes 75 Starrett® combination square 128 Steak knife set 198 Steel-Mokume 180 Steels 180 Stich marker 158 Stick tang blade blanks 216 Stiftenfeile 118 Stifte-Spezialeisen 106 Stool LeiHo 242 Stoßriemen 92 Strop box 222 Strop hanging 223 Strop 222 Stubai®-HSS ring turning tools 104 Suimon hocho 188 Suminagashi folding knife 210 Suminagashi steel blanks 180 Sumitsubo 125 Super speed pruning saw 236 Superhard file rasp 115 Svante-djärv draw knife 54 Svante-djärv carving knives 53 Swan-neck hollowing tool 104 Swedish cowhide 177 Swedish red 168 Swedish steel 180 Synthetic waterstones 85,86

Systainer 155

Tack hammer 159 Taclifter 100Tadafusa hocho 188 Tagua nuts 176 Tailor’s scissors 223,224 Takamura hocho 191 Talmeter® marking measure 123 Tape measures 123 Tape tensioner 138 Tapered chisels 33 Tapered spoon bit 144 Tasai Shinogi Nomi 35 Tataki Nomi 32 Taylor® turning tools 106 Tea bowl 204 Tea bowl cherry bark 204 Telescopic mirror 131 Telescoping pruning saw 237 Telescoping pruning shear 233 Tenon cutter 145 Thonging chisel 158 Timber saw Zorin 237 Titebond® glue 169 Tokico® knife sharpener 89 Tool carrier 154,155 Tool guard 93 Tool rolls and accessories 38 Tool rolls for saws 20 Tool rolls for sculptor’s gouges 45 Toolholder 156 Toolkits 154 Tools for ornamental plants 234 Tormek® accessories 90 Tormek® sharpening system 90 Tower jaws 109 Traditional hocho 185-191 Trattenbacher folding pocket knife 212 Tread chaser set 104 Trenching hoe 228 Trimming shears 231,232 Triple-layer steel 180 Trueing blocks 88Trueing grille for sharpening stones 88 Try squares 127 Turbo-cut frame-saw blade 23 Turbo-cut hand saw 23 Turbo-cut mitre saw blade 26 Turning chucks 108 Turning tool sets 106 Turning tool setter 90 Turning tools 101ff. Turning wood 173 Twisted splitting wedge 61 Two-component glue 169 Two-hand branch shears 233 Two-hand curved adze 55 Two-hand flat adze 55 Two-hand gardening shears 233 Two-hand yariganna 48

Undulate ray leather 177 Universal broad axe 63 Urushi bowls 242

Valtitan files 118 Variable burnisher 80 Variolapper 164 Veneer hammer 99 Veneer knives 132 Veneer saws 24

Veritas® sharpening system 94 Veritas® planes 72 Vice 154 Vine shears 231 Violin pegs 176 V-parting tools 43, 46

Wallets 244 Walnut burls 175 Warding files 116 Water buffalo horn 178 Water pipe pliers 148 Water stone additive 93 Watering can 234 Wave-cutter® drills 143 Wax polish 93 Weed hoe 227 Weeding hoe 228 Western design hocho 191 ff. Western planes 79 Western red cedar 174 Whetstone holder 238 Whetstone 238 White Paper Steel 180 Wiha®-bit set 142 Wiha®-soft face mallet 99 Wild boar tusk 179 Wildlife hatchet 62 Wind bells 240 Wire cutters 147 Wire saw 236 Wolverine sharpening system 94 Wood assortment 173ff.Wood balm 167 Wood carving tools 49ff. Wood drill bit 142,143 Wood files 119 Wood glue 169 Wood sample set 174 Wood Stock® folding ruler 123 Wood threading tools 146Wooden dowels 176 Wooden nails 99Wooden objects, arts and crafts 242 Wooden screwdriver 146Woodfiller 169 Woodworking knife 50 Workbenches 150-151 Working clothes 156 Workshop accessories 149ff. Wrecking bar 100 Wrench 148 Writing utensil blanks 175

Yak horns 178 Yariganna 48

General Terms and Conditions in the version dated 17.06.2010

Scope of these terms and conditionsAll deliveries and services arising from legal transactions conducted between you and us shallbe performed on the basis of the exclusive validity of these General Terms and Conditions(herein after referred to as "GTC") in the version respectively valid upon contract conclusion.1. Exclusive validity of the GTCs, validity of other provisionsOur GTCs are valid for legal transactions conducted between us and companies / commercialcustomers as well as with private individuals as end consumers, unless a differentiation bet-ween consumers and customers is made in the respective clause. Any conflicting businessterms on your part are not valid unless we have explicitly approved them in writing.2. Subject matter of the contractThe exclusive subject matter of the contract is the sold product providing the characteristicsand features contained in our product description. Illustrations on our website or in cataloguesdo not represent any kind of legal binding offer but serve the purpose of being general non-binding product information in a purely visual representation and do not claim to be complete.3. Offers / conclusion of the contract3.1. Our offers are always subject to change and non-binding. To conclude the contract, weshall make the German and English versions of the contract available for you. 3.2. Submittingyour order to us is considered a binding offer to conclude the contract. You shall be bound to this order for a period of 2 weeks. 3.3. For orders not placed on the Internet, the contractshall become effective, within the period mentioned above, as soon as you receive our orderconfirmation (acceptance of order) or as soon as the goods ordered are delivered to you. 3.4. In the event that we cannot accept your offer, we will also notify you within the periodmentioned above. 4. Buyer’s duties to informWhen registering, you shall be obliged to provide true information. Should your data changeduring the term/processing of the contract, you shall be obliged to promptly notify us of thesechanges. If you fail to do so, or if you provide incorrect information in advance, we shall beentitled to cancel the concluded contract at no costs to us. Any costs arising through thegoods being sent to the wrong address due to incomplete or incorrect address details will becharged to your account. As our contractual partner you must ensure that the e-mail accountprovided by you can be reached and that the receipt of e-mails is not excluded due to forwar-ding, shutdown or congestion of the account.5. Right of returnYou may return the goods received within a period of 30 days without stating any reasons simplyby sending them back. This period begins upon receipt of this instruction in writing (e.g. as aletter, fax, e-mail), but neither before the goods have been received by the customer (in caseof recurring deliveries of similar goods not before receiving the first partial delivery) nor beforewe have fulfilled our duty to inform pursuant to article 246 para. 2 in connection with article1 para. 1 and 2 of the Introductory Act to the German Civil Code (EGBGB) and our duties pur-suant to article 312e para.1 sentence 1 of the German Civil Code (BGB) in connection witharticle 246 para. 3 of the EGBGB. Only in case that the goods cannot be returned by parcel(e.g. for bulky goods) you may also return the goods by declaring your request of return in writing.To comply with this term, it is sufficient to send the goods to be returned or your request ofreturn in good time. In any case, the return of the goods shall be at our risk and for ouraccount. Please send the goods or your request of return to the following address: DICK GmbH, Donaustr. 51, D-94526 Metten Consequences of returnIf goods are returned in accordance with these terms and conditions, any services received onboth sides and, if applicable, possible benefits (e.g. from using the service or goods) must bereturned or refunded. If the condition of the goods has deteriorated, compensation for lost valuemay be claimed. This shall not apply, if the deterioration of the goods can exclusively be attri-buted to the examination thereof, as for example in a manner that would be possible in a store.You can avoid any liability for compensation for lost value by not using them in a way as theywould be your property and by refraining from undertaking anything that might affect theirvalue. Any obligations to reimburse payments must be fulfilled within a period of 30 days. The period begins for you upon sending the goods or request of return and for us upon receiptthereof. End of Instructions on Return of Goods6. Terms of delivery and shipping / Place of performance / Transfer of risk6.1. Place of performance for our obligation to supply shall be our head office in 94526Metten/Germany. For shipping of the goods ordered, the following provisions concerning shipping costs described in 6.2 and 6.3. shall apply. Shipping is covered by insurance at all times. It is up to us to choose the route and method of shipping. For legal transactionsbetween us and end consumers, the performance risk in case of shipping shall be transferredto the customer upon handing over of the goods, or if the customer is in default of acceptance.For legal transactions between us and companies/commercial customers, the shipping of thegoods ordered shall be at the customer’s own risk. As soon as we have delivered the goods tothe supplier/forwarding agent in good time, we have fulfilled our obligation to perform the con-tract. For any delays occurring in the delivery process, only the supplier or the customer shallbe responsible. 6.2. The shipping costs arising for orders are not included in the selling priceof the goods. They are disclosed in detail in the online shop on our website at www.more-than-tools.de/shippingcosts and also during the ordering process through our Internet shop as wellas in our catalogue. Unless otherwise agreed, shipping costs must be paid by the customer.For international orders, we reserve the right to choose express deliveries as method of ship-ping, if in this case the shipping costs are lower than by using standard shipping. 6.3. If anyitems of your order are not available on short notice, we reserve the right to send partial deli-veries within the EU. Subsequent deliveries shall be free of shipping costs. For subsequentdeliveries intended to non EU countries, shipping costs need to be charged. 7. Payment methods, Terms of paymentPayment in advance: We grant 2 % discount if payment is made in advance by means of bank transfer.Credit card: We accept Mastercard, Visa, AMEX and Diners. PayPal: Online payment serviceDirect debit: We grant 2% discount, if you authorize us to debit the invoice amount from you-raccount. Invoice: 15 days net, without deductionsCash on delivery (only possible for deliveries within Germany):The cash on delivery charge of 5.50 Euros gross shall be paid by the customer and will be takeninto account in the shipping costs. The invoice amount and the postal charges of 2 Euros mustbe paid to the delivery service. For new customers or in other cases, we reserve the right to restrict the accepted paymentmethod to advance payment by bank transfer, credit card or cash on delivery.For commercial non-EU customers: Please state your EU VAT registration number when placingan order. If you do not have such a registration number or if you fail to submit it, we shall beobliged to invoice you the German VAT according to European law. This provision shall onlyapply to EU customers! Default in payment: The purchase price and shipping costs, if any, aredue upon conclusion of the contract. You shall default on your payments at the latest 15 daysof the due date or receipt of an invoice or equivalent statement of payment. For a consumer,this shall only apply, if he has been explicitly notified of this legal consequence in the invoiceor in an equivalent statement of payment. If you as a buyer default on your payments,we shallbe entitled to charge default interest to consumers to the amount of 5 percent – comparedwith 8 percent for companies/commercial customers – above the base interest rate pursuant to

article 247 of the German Civil Code (BGB). Default in payment occurs either throughreminder after the due date or without reminder on expiry of the payment deadlineaccording to the terms of payment. Claims arising for further damages, in particularadditional costs and costs incurred in making request for payment to the amount of5.00 Euros for a second and last reminder shall not be affected. We shall be entitled tocharge you, the buyer, any bank charges incurred by us due to incorrect or incompleteaccount details provided by you or due to an unauthorized rejection from the bank.However, you shall be entitled to be provided with the evidence that less or no damagehas incurred by us. 8. Prices8.1. The catalogue shows both the net and the gross price. The gross price includes theapplicable value-added tax valid at the time of printing of the catalogue of 7 % or 19 %,depending on the type of product. We reserve the right to adjust the prices, if the VATrate is altered. For the end consumer, the gross price including VAT, which is printed inbold, shall be the only valid and binding price. The net prices are only shown in order toprovide a better overview for our commercial customers and for non-EU customers. 8.2. The prices shown in the catalogue are valid until 1st September 2010. After thisdate, we reserve the right to make price adjustments which are due to short-term pricechanges on the part of our suppliers, currency fluctuations etc. Any order placed after1st September 2010 that has not been placed through our online shop (www.more-than-tools.de) will be accepted on the basis of the catalogue prices (order confirmation), if noprice alterations have been necessary. In the case of necessary price alterations, we willmake you a new price offer which will be sent in written form within a period of 2 weeksof the order received. The contract is only concluded, if you accept this offer within aperiod of 2 weeks of receiving the offer in writing (letter, e-mail, fax). If you do not acceptthe offer, the contract shall not be concluded.You can avoid this complex still necessaryprocedure by placing your order through our online shop.8.3. We accept no liability forprinting errors in terms of price details. 8.4. Book prices: books are price-controlled. In the case of a price increase on the part of the publisher, we shall be obliged to chargeyou the new price.9. Reservation of property All goods delivered shall remain our property until they have been paid in full, regardlessof the expiry of the return period. Being the buyer, the customer is obliged to treat thedelivered goods with care and to promptly notify us of any access to the goods by thirdparties, for example in the case of seizures as well as possible damages or destruction ofthe goods. You are also entitled to resell the goods purchased in regular business trans-actions, provided that you are not in default of payment towards us. However, you haveto assign all claims amounting to the value of the gross invoiced sum to us that resultfrom reselling the goods to a third party. We herewith accept this assignment.10. Removal of defects/ warranty, guarantee10.1. We grant a three-year warranty on the products delivered by us. The warranty claimshall be excluded, if the goods have not been used or maintained properly according tothe manufacturer’s recommendations. The warranty shall be granted after we have chosenthe appropriate remedy, either by repairing the defect product or by delivering a replace-ment product. The warranty period shall begin upon delivery of the goods. Defects inwood intended for further processing shall be excluded from this liability after the expiryof the sale or return (see article 5.). This applies for example to cracks and shrinkage ofthe wood, even if it has been dried artificially. 10.2. In addition to the provision stipulatedunder article 10.1, it shall still be possible to raise legal warranty claims.11. LiabilityOur liability and the liability of our subcontractors for breach of contract as well as fortort shall be restricted to intent and gross negligence. This shall not apply in cases ofharm to life, body and health, claims due to a violation of cardinal obligations, in the caseof guarranteed characteristics and guarantees, for claims due to fraudulent concealmentand to compensation of damage caused by default (article 286 German Civil Code, BGB).In this respect, we shall be liable for all our defaults or those of our subcontractors. Theliability in the case of a default in delivery is, however, restricted to a maximum of nomore than 5 % of the delivery value for each completed week of the default. The liabilityfor a violation of cardinal obligations shall be restricted to foreseeable, typically occur-ring damage. The data communication via the Internet cannot be guaranteed accordingto the present state of the art as being free of defects and/or available at all times.There-fore, we are neither liable for continuous and uninterrupted availability of our online systemnor for the technical and electronic errors occurring during a sales event, which we haveno influence on, in particular not for the delayed processing or acceptance of offers.12. Data protectionWe will use your contractual data only for the purpose of processing your order.We willstore and process all customer data pursuant to the appropriate regulations of the Bundes-datenschutzgesetze (BDSG) (Federal Data Protection Act) and the Telemediengesetz (TMG)(German Act for Telemedia Services). You are at all times entitled to obtain information,to adjust, suspend and delete your stored data free of charge. Your personal data, includingyour home address and e-mail address, will not be passed on by us to third parties withoutyour explicit and (always) revocable consent. The only exception to this regulation refersto our service partners, who require the transmission of data to process orders (e.g. theforwarding company charged with the delivery and the bank charged with the paymentprocessing). In these cases, however, the information transmitted is restricted to therequired minimum.13. Exclusion of liability for external linksOn our website, DICK GmbH refers to other websites on the Internet by placing links.For all these links, the following statement applies: DICK GmbH declares explicitly thatwe have no influence on the presentation or content of any linked sites and therefore wedissociate explicitly from the content of any sites provided by third parties that are linkedfrom www.more-than-tools.de and we affirm that we do not adopt content of externalwebsites. This statement is valid for all links shown and for any contents of the websitesthat the links lead to. 14. Rights to imagesAll rights to images are reserved to DICK GmbH or their partners. It is not permitted touse any images without prior consent. 15. Applicable lawThese General Terms and Conditions and the contract concluded between us on thebasis thereof are subject to the laws of the Federal Republic of Germany to the exclusionof the UN Convention on the International Sale of Goods.16. Court of jurisdictionIf you as the buyer are a legal entity under public law or a separate estate under publiclaw, the exclusive court of jurisdiction for all disputes arising from this contract shall bethe court responsible for our place of business. The same applies, if you as the buyer donot have the general court of jurisdiction in Germany or if your residence or usual placeof residence is not known at the time of the action being filed.17. Severability ClauseShould individual terms of these General Terms and Conditions be or become ineffective,in whole or in part, the validity of the remaining provisions shall not be affected.

Order Hotline:Telephone: +49 (0)991-9109-902 · +49 (0)1805-9109-902*

Fax: +49 (0)991-9109-802 · +49 (0)1805-9109-802**(14 cents/min. from German landlines / calls from mobiles may cost more).

www.more-than-tools.deValue € 5,00

Documents

2010 Katalog More Than Tools