Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
- +
Coulisse B.V., Vonderweg 48, 7468 DC Enter, The Netherlands
ABC-03-U
_R1_
!
indoor use only
233,5
88,3
34
66,0
1 sec 5 sec
Online ResourcesFor the latest information and updated manuals go to www.coulisse.nl.
Obtaining Warranty ServiceFirst follow the advice in this booklet and then go to your local dealer. If the product appears to be damaged or does not function properly, go to your local dealer for instructions on how to obtain warranty service.
User ManualAbsolute ControlVertical Motor ABC-03
WARNING: Important safety instructions. Follow all instructions, since incorrect installation can lead to severe injury.
Do not make repairs yourself. Do not attempt to open the device or disassemble it. You run the risk of electric shock and voiding the limited warranty. No user-serviceable parts are inside.
WARNING:
1. General information
The ABC-03 is a complete kit to motorize Vertical Absolute systems. The motorunit is always situated on the left side of the system. The motorunit is operated with a Coulisse remote control only.The software in the motorunit is selflearning and detects its endpoints automatically.The motorunit contains a motor with a gearbox. An electronic actuator switches between sliding and rotating the slats. Sliding and rotating is possible at every position. The blinds are automatically rotated in a secure position before sliding.
1.1 General dimensions
ABC-03
Powersupply 12-24V DC - 3A
Rated power 36W
Chain speed 4 mtr/min
Tilting Torque 680 mNm
Chain pulling force 2,6 Kg
Max. channels to pair 32 channels
Operating temperature 5 - 60°C
1.2 Performances
1.3 Connectors and buttons
- Pair to a channel/remote(also possible by using ‘SingleSelect’, see manual Remote control*)
2. Programming and operating2.1 Programming
Set in Program mode:Shortly press
program button
Program mode:Blind is
stepping...
Choose channel by pressing
the ChannelSelect button
Pair/unpair by pressing the program button
on the backside of the remote
Exit Program mode:Shortly press
program button
2.2 Operating
- Manual Control- Control by remote
Press program button for more than 2 sec.
Blind rotates as long as button is pressed
(max. 15 sec.)
Exit or press program button another time for more than 2 sec. and
blind moves in opposite direction
Additional blind settings: Available
Switch rotation direction Yes
Favorite position Yes
BatteryMode/solar Yes
We refer to the manual of the Coulisse Remote control to set the additional blind settings.
2.3 Additional blind settings
Disclaimer:
© Copyright Coulisse
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, by any means,
electronic, mechanical, photocopying, recording, digital or otherwise without the written permission of the publisher.
Although this manual has been composed with the most care, Coulisse B.V. does not accept any responsibility for damage
due to mistakes and/or faults in this manual.
Coulisse B.V. reserves the right to revise the manual and to revise and/or changes its content at any time, without obligation to notify
any person or entity of such revisions or changes.
The most recent version replaces older versions of this manual. The most recent version is available at ww.coulisse.nl or contact
your Coulisse contact person.
We invite you to send remarks and comments about this manual to Coulisse at [email protected].
2.5 Reset & initialisation
- Reset to factory defaults
New motors can be initialized directly without resetting
Hold program button until the motor stops for the second time
(ca. 10 sec)
Program mode:Blind is
stepping...
Set in Program mode:Shortly press
program button
- Reset to factory defaults & Erase all paired remotes
Hold program button until the motor stops stepping
and steps once (ca. 15 sec.)
Program mode:Blind is
stepping...
Set in Program mode:Shortly press
program button
- Initialisation (only possible after reset)
1. Connect the motorunit with the 12-24V DC - 3A powersupply2. Detect endpositions:
Shortly press program button
It is important that the run-nertrain first moves outwards. If not, press program button to stop and press it again to change the direction.
Blind is now ready for normal
use.
Blind moves slowly
Wait while blind is detecting the end-
points...(this process will
take a while and may make some noise)
When blind is ready the runnertrain must
be in. Check if all run-ners are aligned. If
not, repeat step 1 & 2 completely.
5. Service & SupportDo not make repairs yourself. Do not attempt to open the device or disassemble it. You run the risk of electric shock and voiding the limited warranty. No user-serviceable parts are inside.
WARNING:
4. Safety & Cleaning4.1 Safety
4.2 CleaningFollow these general rules when cleaning the outside of the device and its components:
- Make sure the device is unplugged.- Use a damp, soft, lint-free cloth. Avoid getting moisture in openings.- Don’t use aerosol sprays, solvents, alcohol, or abrasives.
Do not make repairs yourself. Do not attempt to open the device or disassemble it. You run the risk of electric shock and voiding the limited warranty. No user-serviceable parts are inside.
WARNING:
- Do not let children play with the blind and/or remote control.- Only use powersupplies or batteries that comply with the specifications on the motor.- In case of malfunction, unplug the device or remove the batteries and contact your dealer.- Take care that the blind can move freely and is not blocked by objects.- Take care that the powersupply cable is out of reach for children.- Do not paint the device.- Keep the device dry.
3. Tips & TroubleshootingPlease check www.coulisse.nl for the latest tips and troubleshooting guide
(See manual Remotecontrol)
1 sec 10 sec
1 sec 15 sec
1 sec
> 2 sec
1 sec.
1 sec.
Program button
Antenna
12-24V DC - 3A input
GB2
2.4 Direct take overFrom factory default ‘Direct take over’ function is switched off. The motor moves in small steps when you want to tilt the slats this make it easier to adjust the position of the slats. When you activate direct take over the motor will take over the command directly and runs to its end limit until you push stop button.
Hold program button until the motor stops stepping
(ca. 5 sec.)
Program mode: Blind is
stepping...
Shortly press program button (<2 sec.)