1784-IN046D-EN-P, USB-to-DeviceNet Cable Installation ... · USB-to-DeviceNet Cable 3 Rockwell Automation Publication 1784-IN046D-EN-P - April 2011 Environment and Enclosure ATTENTION:

Installation Instructions

USB-to-DeviceNet CableCatalog Number 1784-U2DN

Topic Page

Important User Information 2

Environment and Enclosure 3

About the Cable 4

Install the Cable 5

Status Indicators 10

Additional Resources 15

2 USB-to-DeviceNet Cable

Important User Information

Solid-state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication SGI-1.1 available from your local Rockwell Automation sales office or online at http://www.rockwellautomation.com/literature/) describes some important differences between solid-state equipment and hard-wired electromechanical devices. Because of this difference, and also because of the wide variety of uses for solid-state equipment, all persons responsible for applying this equipment must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment, which may lead to personal injury or death, property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property damage, or economic loss. Attentions help you identify a hazard, avoid a hazard and recognize the consequences.

SHOCK HAZARD: Labels may be on or inside the equipment, for example, drive or motor, to alert people that dangerous voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment, for example, drive or motor, to alert people that surfaces may reach dangerous temperatures.

IMPORTANT Identifies information that is critical for successful application and understanding of the product.

Rockwell Automation Publication 1784-IN046D-EN-P - April 2011

http://literature.rockwellautomation.com/idc/groups/literature/documents/in/sgi-in001_-en-p.pdfhttp://www.rockwellautomation.com/literature/

USB-to-DeviceNet Cable 3

Environment and Enclosure

ATTENTION: This equipment is intended for use in overvoltage Category II applications (as defined in IEC 60664-1), at altitudes up to 2000 m (6562 ft) without derating.

This equipment is considered Group 1, Class A industrial equipment according to IEC/CISPR 11. Without appropriate precautions, there may be potential difficulties with electromagnetic compatibility in residential and other environments due to conducted and radiated disturbances.

This equipment is supplied as enclosed equipment. It should not require additional system enclosure when used in locations consistent with the enclosure type ratings stated in the Specifications section of this publication. Subsequent sections of this publication may contain additional information regarding specific enclosure type ratings, beyond what this product provides, that are required to comply with certain product safety certifications.

In addition to this publication, see the following:

Industrial Automation Wiring and Grounding Guidelines, , publication 1770-4.1, for additional installation requirements

NEMA Standard 250 and IEC 60529, as applicable, for explanations of the degrees of protection provided by enclosures

At the end of its life, this equipment should be collected separately from any unsorted municipal waste.


message URL http://www.literature.rockwellautomation.com/idc/groups/literature/documents/in/1770-in041_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/in/1770-in041_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/in/1770-in041_-en-p.pdf


About the CableThe 1784-U2DN USB-to-DeviceNet cable lets you connect a computer to a DeviceNet network via an unused USB port on the computer.

The 1784-U2DN cable replaces the 1784-PCD communication card.

The cable operates at data rates of 125 Kbps, 250 Kbps, and 500 Kbps.

IMPORTANT To comply with the CE low voltage directive (LVD), this equipment must be powered from a source compliant with safety extra low voltage (SELV) or protected extra low voltage (PELV).

IMPORTANT The data rate is read only when power is applied. To change the data rate, you must disconnect the cable from the USB port, use the data rate switch to change the data rate setting, then reconnect the cable to the USB port.

USB Cable

Data Rate (DR) Switch

Status Indicators

Five-pin Female DeviceNet Network ConnectorNode Address

Switches



These are the firmware variations:

Cables with version 1.009 or later contain a fix for an anomaly whereby timeouts could be experienced while monitoring parameters of some devices. The initial installation of a 1784-U2DN USB-to-DeviceNet cable will no longer cause the Windows operating system to report an error code 10.

Cables with version 1.008 or later have an explicit message size of 500 bytes, which allows uploading from a SmartGuard controller.

Install the CableFollow these procedures to install the cable.

ATTENTION: Prevent Electrostatic Discharge

This equipment is sensitive to electrostatic discharge, which can cause internal damage and affect normal operation. Follow these guidelines when you handle this equipment:

Touch a grounded object to discharge potential static. Wear an approved grounding wriststrap. Do not touch connectors or pins on component boards. Do not touch circuit components inside the equipment. Use a static-safe workstation, if available. Store the equipment in appropriate static-safe packaging when

not in use.

ATTENTION: USB connection length must be less than 3 m (9.84 ft). Do not attempt to extend the cable.



Obtain the Device Driver for the CableFollow these steps to download and install the device driver for the cable.

1. Visit http://www.rockwellautomation.com/knowledgebase/.

2. Open tech note ID 53280 and follow the instructions to install the driver.

Configure and Connect the Cable

1. Use the data rate (DR) switch on the side of the connector to set the network data rate to 125 Kbps or Auto.

2. Use the rotary switches to set the module node address to a valid number (063).

3. Insert the end of the cable with the USB connector into a USB port on a computer.

IMPORTANT A minimum of RSLinx Classic software, version 2.51, is required for use with the cable.

IMPORTANT If RSLinx Classic software, version 2.54 or later, is installed on the computer, the device driver is already installed on the computer. Skip this section.

Node Address (rotary) Switches

Data Rate (DR) Switch


http://www.rockwellautomation.com/knowledgebasehttp://www.rockwellautomation.com/support/pccards


4. Insert a DeviceNet network cable into the five-pin female DeviceNet network connector.

TIP A 10-pin plug-in connector (catalog number 1787-PLUG10R, PN-94220605) is shipped with the 1784-U2DN cable. See the figure and chart for wiring.

Five-pin Female DeviceNet Network Connector

Connect To

Red wire V+

White wire CAN High

Bare wire Shield

Blue wire CAN Low

Black wire V-



Change the Data RateThe 1784-U2DN cable can automatically detect the data rate being used on an active DeviceNet network. To use this feature, set the data rate (DR) switch to Auto. If the cable does not detect any network traffic for a period of 12 seconds after it is plugged into the USB port, it will set itself to a fallback data rate. The factory-default fallback data rate is 125 Kbps.

You can change the fallback data rate either manually or with RSNetWorx for DeviceNet software.

Manually Set the Data Rate

1. Unplug the cable from the USB port.

2. Set the rotary address switches to 90 for 125 Kbps, 91 for 250 Kbps, or 92 for 500 Kbps.

3. Plug the cable into the USB port and wait for the cable to finish powering up.

4. Unplug the cable from the USB port.

5. Set the rotary address switches to a valid address (0...63).

6. Plug the cable into the USB port.

TIP Manually selecting 125 Kbps and using the fallback data rate lets the cable communicate with devices on a network that does not have active traffic (for example, a network consisting of slaves and no master) for node commissioning.



Use RSNetWorx for DeviceNet Software to Set the Speed

1. Start RSNetWorx for DeviceNet software.

2. From the Tools menu, choose Node Commissioning.

3. Click Browse and navigate to the 1784-U2DN cable to be modified.

4. Change the data rate and click Apply.

Product DimensionsThe following illustration shows the product dimensions.

IMPORTANT The fallback rate can be set only with the software when the link speed switch is in the Auto position.

TIP You cannot change the node address with software. You can set the node address only by using the rotary switches on the module.

USB Cable Length 0.61 m (2 ft)

EnclosureLength: 7.62 cm (3 in.)Width: 5.08 cm (2 in.)Thickness: 2.54 cm (1 in.)



Status IndicatorsThe following table describes the cable status indicators.

Status Indicators

Indicator Status Description

USB Green The cable is configured, but no network traffic is present.

Flashing green Network traffic is present.

Off Unable to transfer data: Disconnected from host. In one of the following states:

Default Powered Address Suspend

USB Network Status

Module Status



Traffic Analyzer SoftwareThe 1784-U2DN cable is designed to work with Frontlines NetDecoder traffic analyzer software. For more information on Frontlines product, go to either http://www.rockwellautomation.com/encompass/ or http://www.fte.com.

Module Status (MS) Green The cable is operating normally.

Off No power to the cable.

Flashing green The cable is operating in a normal condition and is online with no connections established: The cable may be in Standby mode. The cable needs commissioning due to

missing, incomplete, or incorrect configuration.

Flashing red The cable has a recoverable fault.

Red The cable has an unrecoverable fault and may need to be replaced.

Flashing red/green

The cable is performing a self-test.

Network Status (NS) Off The cable has not yet completed the Dup_MAC_ID test.

The cable may not be powered (if the Module Status indicator is off).

No network power present.

Flashing green The cable is online, and has passed the Dup_MAC_ID test, but has no established connections to the other nodes.

Green The cable is online and has established connections to the other nodes.

Red The cable has detected a communication error, such as a duplicate MAC ID or bus-off condition.

Status Indicators

Indicator Status Description


http://www.rockwellautomation.com/encompass/http://www.fte.com


Specifications

Technical Specifications - 1784-U2DN

Attribute 1784-U2DN

Enclosure type rating Meets IP30

USB Supply 75 mA @ 5V DC

DeviceNet Supply 70 mA @ 24V DC

Power consumption 0.5 W

Power dissipation 0.5 W

Isolation voltage 30V (continuous), basic insulation typeType tested at 500V AC for 60 s, DeviceNet network to USB

Weight, approx. 0.11 kg (0.23 lb)

Wire size DeviceNet network:0.053.3 mm2 (3012 AWG) solid or stranded copper wire rated at 75 C (167 F) or greater 1.2 mm (3/64 in.) insulation max

Wiring category(1)

(1) Use this Conductor Category information for planning conductor routing. Refer to Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1.

2 - on communication ports

Terminal block torque DeviceNet network:0.60.8 Nm (5.07.0 lbin)


http://www.literature.rockwellautomation.com/idc/groups/literature/documents/in/1770-in041_-en-p.pdf


Environmental Specifications - 1784-U2DN

Attribute 1784-U2DN

Temperature, operating IEC 60068-2-1 (Test Ad, Operating Cold) IEC 60068-2-2 (Test Bd, Operating Dry Heat) IEC 60068-2-14 (Test Nb, Operating Thermal

Shock)

055 C (32131 F)

Temperature, nonoperating IEC 60068-2-1

(Test Ab, Unpackaged Nonoperating Cold) IEC 60068-2-2

(Test Bb, Unpackaged Nonoperating Dry Heat) IEC 60068-2-14

(Test Na, Unpackaged Nonoperating Thermal Shock)

-1085 C (14185 F)

Relative humidityIEC 60068-2-30 (Test Db, Unpackaged Damp Heat)

595% noncondensing

Shock, nonoperatingIEC 60068-2-27 (Test Ea, Unpackaged Shock)

1000 mm (3.28 ft)

EmissionsCISPR 11

Group 1, Class A

ESD immunityIEC 61000-4-2

8 kV air discharges

Radiated RF immunityIEC 61000-4-3

10V/m with 1 kHz sine-wave 80%AM from 802000 MHz

10V/m with 200 Hz 50% Pulse 100%AM at 900 MHz

10V/m with 200 Hz 50% Pulse 100%AM at 1890 MHz

3V/m with 1 kHz sine-wave 80%AM from 20002700 MHz

EFT/B immunityIEC 61000-4-4

2 kV at 5 kHz on DeviceNet port

Surge transient immunityIEC 61000-4-5

2 kV line-earth (CM) on DeviceNet port

Conducted RF immunityIEC 61000-4-6

10V rms with 1 kHz sine-wave 80% AM from 150 kHz80 MHz on DeviceNet port



Certifications - 1784-U2DN

Certification(1) (when product is marked)

1784-U2DN

c-UL-us UL Listed Industrial Control Equipment, certified for US and Canada. See UL File E65584.

CE European Union 2004/108/EC EMC Directive, compliant with: EN 61326-1; Meas./Control/Lab.,

Industrial Requirements EN6100-6-2; Industrial Immunity EN 61000-6-4; Industrial Emissions EN 61131-2; Programmable Controllers

(Clause 8, Zone A & B)

C-Tick Australian Radiocommunications Act, compliant with: AS/NZS CISPR 11; Industrial Emissions

ODVA ODVA conformance tested to DeviceNet specifications

(1) See the Product Certification link at http://www.ab.com for Declarations of Conformity, Certificates, and other certification details.


http://www.ab.com


Additional ResourcesThese documents contain additional information concerning related products from Rockwell Automation.

You can view or download publications at http://www.rockwellautomation.com/literature/. To order paper copies of technical documentation, contact your local Allen-Bradley distributor or Rockwell Automation sales representative.

Resource Description

DeviceNet Media Design and Installation Guide, publication DNET-UM072

Provides DeviceNet network planning information.

Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1

Provides general guidelines for installing a Rockwell Automation industrial system.

Product Certifications website, http://www.ab.com

Provides declarations of conformity, certificates, and other certification details.


http://literature.rockwellautomation.com/idc/groups/literature/documents/um/dnet-um072_-en-p.pdfhttp://www.rockwellautomation.com/literature/http://www.literature.rockwellautomation.com/idc/groups/literature/documents/in/1770-in041_-en-p.pdfhttp://www.ab.com

Rockwell Otomasyon Ticaret A.., Kar Plaza Merkezi E Blok Kat:6 34752 erenky, stanbul, Tel: +90 (216) 5698400

Rockwell Automation SupportRockwell Automation provides technical information on the Web to assist you in using its products. At http://www.rockwellautomation.com/support/, you can find technical manuals, a knowledge base of FAQs, technical and application notes, sample code and links to software service packs, and a MySupport feature that you can customize to make the best use of these tools.

For an additional level of technical phone support for installation, configuration, and troubleshooting, we offer TechConnect support programs. For more information, contact your local distributor or Rockwell Automation representative, or visit http://www.rockwellautomation.com/support/.

Installation AssistanceIf you experience a problem within the first 24 hours of installation, please review the information that's contained in this manual. You can also contact a special Customer Support number for initial help in getting your product up and running.

New Product Satisfaction ReturnRockwell Automation tests all of its products to ensure that they are fully operational when shipped from the manufacturing facility. However, if your product is not functioning and needs to be returned, follow these procedures.

Documentation Feedback Your comments will help us serve your documentation needs better. If you have any suggestions on how to improve this document, complete this form, publication RA-DU002, available at http://www.rockwellautomation.com/literature/.

United States or Canada 1.440.646.3434

Outside United States or Canada

Use the Worldwide Locator at http://www.rockwellautomation.com/support/americas/phone_en.html, or contact your local Rockwell Automation representative.

United StatesContact your distributor. You must provide a Customer Support case number (call the phone number above to obtain one) to your distributor to complete the return process.

Outside United States Please contact your local Rockwell Automation representative for the return procedure.

Publication 1784-IN046D-EN-P - May 2011 PN-111579Supersedes Publication 1784-IN046C-EN-P - July 2009 Copyright 2011 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.

Allen-Bradley, Rockwell Software, Rockwell Automation, SmartGuard, RSLinx Classic, RSNetWorx for DeviceNet, Encompass, and TechConnect are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

http://www.rockwellautomation.com/support/http://www.rockwellautomation.com/support/http://www.rockwellautomation.com/locations/http://www.rockwellautomation.com/support/americas/phone_en.htmlhttp://www.rockwellautomation.com/literature/

1784-IN046D-EN-P, USB-to-DeviceNet Cable Installation InstructionsImportant User InformationEnvironment and EnclosureAbout the CableInstall the CableObtain the Device Driver for the CableConfigure and Connect the CableChange the Data RateProduct Dimensions

Status IndicatorsTraffic Analyzer Software

Additional ResourcesBack Cover

/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /CropGrayImages true /GrayImageMinResolution 300 /GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true /GrayImageDownsampleType /Average /GrayImageResolution 300 /GrayImageDepth 8 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 2.00000 /EncodeGrayImages true /GrayImageFilter /FlateEncode /AutoFilterGrayImages false /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /CropMonoImages true /MonoImageMinResolution 1200 /MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true /MonoImageDownsampleType /Average /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects false /CheckCompliance [ /None ] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile (None) /PDFXOutputConditionIdentifier () /PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped /False

/Description > /Namespace [ (Adobe) (Common) (1.0) ] /OtherNamespaces [ > /FormElements false /GenerateStructure true /IncludeBookmarks false /IncludeHyperlinks false /IncludeInteractive false /IncludeLayers false /IncludeProfiles true /MultimediaHandling /UseObjectSettings /Namespace [ (Adobe) (CreativeSuite) (2.0) ] /PDFXOutputIntentProfileSelector /NA /PreserveEditing true /UntaggedCMYKHandling /LeaveUntagged /UntaggedRGBHandling /LeaveUntagged /UseDocumentBleed false >> ]>> setdistillerparams> setpagedevice

Introduction_Catagory Types

This tab summarizes Rockwell Automation Global Sales and Marketing preferred printing standards. It also provides guidance on whether a publication should be released as JIT (print on demand) or if it requires an RFQ for offset printing.Find your publication type in the first section below. Use the assigned Printing Category information to determine the standard print specifications for that document type. The Printing Categories are defined below the Publication Type section. Note there may be slightly different print specifications for the categories, depending on the region (EMEA or Americas).For more information on Global Sales and Marketing Printing Standards, see publication RA-CO004 in DocMan.

Publication Type and Print Category

Publication TypeOff Set Print Category Spec. (See table below)JIT Spec. (See table below)DescriptionOrder Min **Order Max **Life Cycle Usage / Release Option

ADNA - PuttmanNAAdvertisement Reprint ColourNANAPresale / Internal

APA3D2Application Solution or Customer Success Story5100Presale / External

ARNANAArticle/Editorial/BylineNANAPresale / Internal

(press releases should not be checked into DocMan or printed)

ATB3, B4D5Application techniques5100Presale / External

BRA2 Primary, A1NABrochures5100Presale / External

CAC2 Primary, C1NACatalogue150Presale / External

CGNANACatalogue Guide150Presale / External

CLNANACollection550Presale / External

COA5, A6, A9D5Company Confidential InformationNANANA / Confidential

CPE-onlyE-only, D5Competitive Information550NA / Confidential

DCE-onlyE-onlyDiscount SchedulesNANAPresale / Internal

DIA1, A3NADirect Mail5100Presale / Internal

DMNANAProduct Demo550Presale / Internal

DSB3D5Dimensions Sheet15Post / External

DUB3D5Document Update15Post / External

GRB2D6Getting Results15Post / External

INB3 Primary, B2D5, D6Installation instructions15Post / External

LMNANALaunch Materials550Presale / Internal

PCB3D5Packaging Contents

PLE-only primary, B3E-onlyPrice List550Presale / Internal

PMB2D6Programming Manual15Post / External

PPA3D1Profile (Single Product or Service). NOTE: Application Solutions are to be assigned the AP pub type.5100Presale / External

QRB2 primary, B3, B5D5, D6Quick Reference15Post / External

QSB2 primary, B3, B5D5, D6Quick Start15Post / External

RMB2D5, D6Reference Manual15Post / External

RNB3D5Release Notes15Post / External

SGB1 Primary, B4D5, D6Selection Guide Colour550Presale / External

SGB2D5, D6Selection Guide B/W550Presale / External

SPA1, A2, A3, A4NASales Promotion NOTE: Service profiles are to be assigned the PP pub type.5100Presale / Internal

SRB2, B3D5, D6Specification Rating Sheet5100Presale / External

TDB2 Primary B3, B4, B5D5, D6Technical Data550Presale / External

TGB2, B3D6Troubleshooting Guide15Post / External

UMB2 Primary, B4D6User Manual B/W15Post / External

WDB3D5Wiring Diagrams / Dwgs15Post / Internal

WPB3 Primary, B5D5White Paper550Presale / External

** Minimum order quantities on all JIT items are based on the publication length. **

Publication lengthMinimum Order Quantity

77 or more pages1 (no shrink wrap required)

33 to 76 pages25

3 to 32 pages50

1 or 2 pages100

Pre-sale / MarketingAll paper in this category is White Brightness, 90% or better. Opacity 90% or better

CategoryColor OptionsAP, EMEA Paper RequirementsCanada, LA, US Paper Requirements

A14 color170 gsm 2pp100# gloss cover, 100# gloss text

A24 color170 gsm , folded, 4pp100# gloss cover, 80# gloss text

A34 colorCover 170 gsm with Body 120 gsm, > 4pp80# gloss cover, 80# gloss text

A42 color170gsm Silk 120gsm Silk80# gloss cover, 80# gloss text

A52 color170gsm Silk 120gsm Silk80# gloss cover, 80# matt sheet text

A61 color170gsm Silk 120gsm Silk80# gloss cover, 80# matt sheet text

A74 color cover2 color textSelection GuideCategory being deleted10 Point Cover C2S50# matte sheet text

A84 color coverCategory being deleted50# matte sheet text, self cover

2 color text

Selection Guide

A92 color100gsm bond50# matte sheet text, self cover

Selection Guide

Gray shading indicates Obsolete Print Catagories

Post Sale / Technical Communication


B14 color cover270gsm Gloss 100gsm bond10 Point Cover C2S

2 color text50# matte sheet text

B21 color160gsm Colortech & 100gsm Bond90# Cover50# matte sheet text

B31 color100gsm bond50# matte sheet text, self cover

B42 color160gsm Colortech & 100gsm Bond90# Cover50# matte sheet text

B52 color100gsm bond50# matte sheet text, self cover

Catalogs


C14 color cover270gsm Gloss 90gsm silk10 Point Cover C2S

4 color text45# Coated Sheet

C24 color cover270gsm Gloss 80gsm silk10 Point Cover C2S

2 color text32#-33# Coated Sheet

JIT / PODAll paper in this category is White Brightness, 82% or better. Opacity 88% or better


D14 color170gsm white silk80# gloss cover, coated 2 sides

D24 color120gsm white silk80# gloss text, coated 2 sides, self cover

D34 colorCover 170gsm with Body 120gsm80# gloss cover, 80# gloss text coated 2 sides

D41 color160gsm tab90# index

D51 color80gsm bond20# bond, self cover

D61 colorCover 160gsm tab with Body 80gsm bond90# index, 20# bond

D72 color160gsm tab90# index

D82 color80gsm bond20# bond, self cover

D92 colorCover 160gsm tab with Body 80gsm bond90# index, 20# bond

D10Combination: 4 color cover, with 2 color bodyCover 160gsm with Body 80gsm90# index, 20# bond

Gray shading indicates Obsolete Print Catagories

Just In Time (JIT) or Off Set (OS)?

Use these guidelines to determine if your publication should be JIT (just in time/print on demand) or if it would be more economical to print OS (offset/on a press). OS print jobs require an RFQ (Request For Quote) in US. If your job fits into the Either category, an RFQ is recommended, but not required. In the US, RA Strategic Sourcing will discourage or reject RFQs for jobs that fall within the JIT category. Guidelines differ for black & white and color printing, so be sure to check the correct tables.

Black & White Printing

Color Printing

Color Printing

Print Spec Sheet

JIT Printing SpecificationsRA-QR005G-EN-P - 3/29/2010

Printing SpecificationYOUR DATA HEREInstructionsNO

(required) Category:B3Select Print Category A,B,C or D from category list, on "Introduction_Catagory Types" tab11 x 17LOOSE -Loose LeafYESPre-sale / MarketingTOP

(required) Finished Trim Size Width:4.75 x 7 (slightly smaller half-size)8.5 x 11PERFECT - Perfect BoundA1LEFT

(required) Publication Number :1784-IN046D-EN-PSample: 2030-SP001B-EN-P3 x 5SADDLE - Saddle StitchA2RIGHTCORNER

Use Legacy NumberNoYES or NO18 x 24 PosterPLASTCOIL - Plastic Coil (Coil Bound)A4BOTTOMSIDE

Legacy Number if applicable:Sample Legacy Number: 0160-5.3324 x 36 PosterSTAPLED1 -1 positionA3

Publication Title:USB-to-DeviceNet Cable Installation InstructionsSample: ElectroGuard Selling Brief80 character limit - must match DocMan Title36 x 24 PosterSTAPLED1B - bottom 1 positionA5

(required) Business Group:Marketing CommercialAs entered in DocMan4 x 6STAPLED2 - 2 positionsA6

(required) Cost Center:CMKMKE CM Integrated Arch - 19021As entered in DocMan - enter number only, no description. Example - 19021CMKMKE CM Integrated Arch - 19021CMKMKE Market Access Program - 191054.75 x 7 (slightly smaller half-size)THERMAL - Thermal bound (Tape bound)A7

Binding/Stitching:SADDLE - Saddle StitchReview key on right...Saddle-Stitch Items All page quantities must be divisible by 4.Note: Stitching is implied for Saddle-Stitch - no need to specify in Stitching Location.80 pgs max. on 20# (text and cover)76 pgs max. on 20# (text) and 24# (cover)72 pgs max. on 24# (text and cover)

Perfect Bound Items940 pgs max. w/cover (90# index unless indicated otherwise)70 pgs. min. for spine without words200 pgs min. for spine with words

Plastcoil Bound Items530 pgs max. of 20# (if adding cover deduct equivalent number of pages to equal cover thickness) (90# index unless indicated otherwise)

Tape Bound Items250 pgs max. on 20# no cover240 pgs max. w/cover (90# index unless indicated otherwise)4.75 x 7.75THERMALO - Thermal Bound (Tape bound - offline)A8

(required) Page Count of Publication:16Total page count including cover5.5 x 8.5 (half-size)A9

Paper Stock Color:White is assumed. For color options contact your vendor.6 x 4Post Sale / Technical Communication

Number of Tabs Needed:5 tab in stock at RR Donnelley7.385 x 9 (RSI Std)B1

Stitching Location:Blank, Corner or Side8.25 x 10.875B2

Drill Hole YES/NONOAll drilled publications use the 5-hole standard, 5/16 inch-size hole and a minimum of inch from the inner page border.8.25 x 11 (RA product profile std)B3None

Glue Location on Pad:Glue location on pads8.375 x 10.875B4Half or V or Single Fold

Number of Pages per Pad:Average sheets of paper.. 25, 50 75,100 Max9 x 12 (Folder)B5C or Tri-Fold

Ink ColorOne color assumes BLACK / 4 color assume CMYK / Indicate PMS number hereA4 (8 x 11 ) (210 x 297 mm)CatalogsDbleParll

Used in Manufacturing:A5 (5.83 x 8.26) (148 x 210 mm)C1Sample

Fold:Review key on right...Short (must specify dimensions between folds in Comments)

Comments:C2Z or Accordian Fold

Part Number:PN-111579JIT / PODMicrofold or French Fold - designate no. of folds in Comments - intended for single sheet only to be put in box for manufacturing

D1Double Gate

D2

FoldsHalf, V, Single C or Tri

Dble Parll

Z or Accordian Microfold or French

Double Gate

Short FoldD3

D4

D5

D6

D7

D8

D9

MBD000CCD74.bin

MBD000D141F.bin

MBD000E357A.bin

MBD000D05AE.bin

MBD000B37AA.bin

MBD000C2CF0.bin

MBD000CBFEF.bin

MBD000B71E5.bin

MBD000AB9B4.bin

MBD000AF7AA.bin

Documents

1784-IN046D-EN-P, USB-to-DeviceNet Cable Installation ... · USB-to-DeviceNet Cable 3 Rockwell Automation Publication 1784-IN046D-EN-P - April 2011 Environment and Enclosure ATTENTION: