Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
Breaker plate settings .............................................................................6" and 4"Material source ............................................................................... from surge binMaterial .................................................................................................... limestone
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
% Passing
#30 #16 #8 #4 1/4" 1/2" 1" 2" 3" 4"
Sieve Size
475 rpm
415 rpm
375 rpm
ScreenSize
% Passing375 RPM
% Passing415 RPM
% Passing475 RPM
6" 100.0 100.0 100.0
4" 77.9 86.6 91.2
3" 67.2 82.0 84.5
2" 50.1 70.8 73.0
1" 30.2 41.7 48.6
3/4" 22.0 34.1 40.0
1/2" 17.6 26.0 34.5
#4 7.8 14.9 20.7
#8 5.2 10.7 15.2
#16 3.4 8.2 11.7
#30 1.5 6.3 9.4
#50 1.1 4.2 5.9
#100 0.7 2.2 3.4
#200 0.5 1.1 1.7
Rotor Speed
RPM Rotor Tip Speed ft/min
375 5989
415 6627
475 7586
Terex® Minerals Processing SystemsCedarapids 1516 Andreas-Type Primary
1516 GRADATION CURVE AND CHART
Effective Date: October 2011. Product specifications and prices are subject to change without notice or obligation. The photographs and/or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex makes no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and/or its subsidiaries in the USA and other countries. All rights are reserved. Terex is a registered trademark of Terex Corporation in the USA and many other countries. © 2011 Terex Corporation.
Terex® Minerals Processing Systems, 909 17th Street NE, Cedar Rapids, IA 52402 USATel +1 319 363 3511 Fax +1 319 399 4871 www.terexmps.com
Form 22786 (10/11)
www.terexmps.com
SPECIFICATIONS
GRADATION CURVE
THE ANDREAS IMPACTOR: DESIGNED TO DELIVER
ADVANCED PERFORMANCE FEATURES
QUICK CHANGE PRIMARYBREAKER PLATEQuick change (reversible) cast manganese mono-block primarybreaker plate lifts out for changes with pivot shaft in place. Adjusts to 12” (305 mm).
EASY ACCESS HYDRAULIC OPENINGFully integrated hydraulic systemopens upper section. Power unit bolts to base frame and can be easilyrelocated. A full 16” (406 mm) swingon aprons passes uncrushables.
OPEN DISC 3 OR 4 BAR 61” (1549 mm) DIAMETER ROTORRugged rotor with massive 5 1/4”(133 mm) thick backer bars provides high inertia in a portableweight range. Features 4” (102 mm)patented quick-change wedge system.
The Andreas HorizontalShaft Impactor can be configured to fit with either stationary or portable plant operations.
Cedarapids impactorsare known for ruggedconstruction, high productivity and agreater value for investment. Our customers know theycan depend on thestrongest dealer network in the industry.
909 17th Street NE, Cedar Rapids, IA 52402 USAtel 319-363-3511 fax 319-399-4871
www.cedarapids.com
DELIVERING UNPRECEDENTED CRUSHINGPOWER, THE ANDREAS IMPACTOR ISDESIGNED TO GIVE YOU THE ADVANTAGE.
LOWER COST PER TONLarger feed opening and feeder, increased capacity, and a higher reduction ratio mean you crush more rock for the money.
GREATER PRODUCT CONTROL Quick impeller bar changes and quick change breakerplates allow for better control of product size.
DURABLE DESIGN FOR GREATER UPTIMERugged design and construction give you the continuous high quality output you need to add profit to your bottom line.
SIMPLIFIED MAINTENANCE Convenient access with three inspection doors and removable top for breaker plate access.
A single wrench is used to open inspection doors and crusher frame lock bolts. Patent pending quickturn wedge system offers fast and easy bar rotation or replacement.
FEED OPENINGANDREAS 1516 — 40” x 65”(1016 mm x 1651 mm)ANDREAS 1520 — 40” x 81”(1016 mm x 2057 mm)
CRUSHER WEIGHTANDREAS 1516 — 55,000 lbs (24,948 kg) (approx.)ANDREAS 1520 — 67,400 lbs (30,572 kg) (approx.)
SPECIFICATIONSHORSEPOWERANDREAS 1516 — 500 - 600ANDREAS 1520 — 600 - 700
PRODUCTIVITYANDREAS 1516 —
Up to 600 TPH (544 MTPH)ANDREAS 1520 —
Up to 800 TPH (726 MTPH)
THREE BAR ROTORANDREAS 1516 — 61” - 64”(1549 mm x 1626 mm)ANDREAS 1520 — 61” - 80”(1549 mm x 2032 mm)
MAX FEED SIZE 34” (864 mm)
220 mm BEARINGS
23351 (01/04)
0908
Cedarapids IP 1516 Impact Crusher
Power. Volume. Control.
With its large feed opening, large capacity and high
reduction ratio, the Terex® Cedarapids 1516 horizontal
shaft impactor delivers extraordinary crushing power,
plus high production volume.
Rapid blowbar and quick change breaker plates allow
for better control of product size.
Three inspection doors and a removable top facilitate
easy breaker plate access. The patented quick turn
wedge system permits fast and simple bar rotation
and bar replacement.
Cedarapids IP 1300 Series
Big on Volume. Big on Power.
With their large feed openings, heavy duty aprons and
rugged rotors, the 1300 series crushers are designed to
handle big feed sizes and high capacity crushing.
The patented wedge bar system is just one of many
features that ensure reliable operation. Maintenance is
fast and easy, which helps minimize downtime.
Static Materials Processing Technology
Static Materials Processing Technology
Model Capacity Motor SizeInlet Size
(mm)
Maximum Recommended
Feed Size
Rotor Size Di-ameter x Width
(mm)
Basic Crusher Weight
Number of Blowbars
Cedarapids IP 1313
150–300 tph (135–270 mtph)
300 hp (225 kW)
43 x 49” (1100 x 1240)
34” (865 mm)
50 x 48” (1270 x 1220)
30,800 lbs (13,970 Kg)
3 or 4
Cedarapids IP 1316
250 – 400 tph (225–365 mtph)
400 hp (300 kW)
43 x 64” (1100 x 1645)
34” (865 mm)
50 x 64” (1270 x 1625)
38,500 lbs (17,465 Kg)
3
Model Capacity Motor SizeInlet Size
(mm)
Maximum Recommended
Feed Size
Rotor Size Di-ameter x Width
(mm)
Basic Crusher Weight
Number of Blowbars
Cedarapids IP 1516
600–800 tph (545–725 tph)
600 hp (450 kW)
52 x 65” (1320 x 1650)
34” (865 mm)
61 x 64” (1550 x 1625)
55,700 lbs (25,260 Kg)
3
Horizontal Shaft Impactors
Terex® HSI 4143 Impact Crusher
Flexible. Cost effective. Responsive.
With its hydraulic assist apron adjustment for quick setting
changes, the 4143 horizontal shaft impactor is a highly cost
effective crusher that is easy to operate and easy to maintain.
There are four inspection doors plus a hinged side door for
inspection access to the rotor, blowbars and aprons. The
chamber hydraulically opens for general maintenance and for
turning or replacing the blowbars. The quick-release wedge-
lock system makes changing blowbars a breeze.
An optional blowbar jib crane is available for added flexibility
and convenience.
Model Capacity Motor SizeInlet Size
(mm)
Maximum Recommended
Feed Size
Rotor Size Di-ameter x Width
(mm)
Basic Crusher Weight
Number of Blowbars
HSI 4143910–300 tph
(80–270 mtph)180 hp
(130 kW)31” x 44”
(800 x 1130)20”
(500 mm)41” x 43”
(1035 x 1100)21,915 lbs
(9,940 kg)4