14H001R4_PC

For P

ublic

Com

ment

DRAFT MALAYSIAN 14H001R4

STANDARD STAGE : PUBLIC COMMENT (40.20)

DATE : 01/07/2014 - 31/08/2014

Diesel fuel - Specification - Part 1: Euro 2M (Fourth revision) OFFICER/SUPPORT STAFF: (ZB/)

ICS: 75.080 Descriptors: diesel, EURO 2M, specifications, test method

Copyright 2014

DEPARTMENT OF STANDARDS MALAYSIA

For P

ublic

Com

ment

14H001R4

STANDARDS MALAYSIA 2014 - All right reserved i

Contents

Page Committee representation ..........................................................................................................ii Foreword .................................................................................................................................... iii 1 Scope ............................................................................................................................ 1 2 Normative references ................................................................................................... 1 3 Composition and properties .......................................................................................... 1 4 Sampling ....................................................................................................................... 1 5 Packing and marking .................................................................................................... 2 Annex A Normative references ............................................................................................. 4 Annex B Alternatives test method ........................................................................................ 6 Bibliography ............................................................................................................................... 7

For P

ublic

Com

ment

14H001R4

STANDARDS MALAYSIA 2014 - All right reserved ii

Committee representation The Industry Standards Committee on Petroleum and Gas (ISC H) under whose authority this Malaysian Standard was developed, comprises representatives from the following organisations: Association of Malaysian Oil and Gas Engineering Consultants Department of Occupational Safety and Health Malaysia Department of Standards Malaysia Federation of Malaysian Manufacturers - Malaysian Industrial Gases Manufacturers Group Jabatan Bomba dan Penyelamat Malaysia Jabatan Pengangkutan Jalan Malaysia Kastam Diraja Malaysia Malaysian Gas Association Malaysian Palm Oil Board Malaysian Plastics Manufacturers Association Ministry of Domestic Trade, Co-operatives and Consumerism Ministry of International Trade and Industry Petroliam Nasional Berhad PETRON Malaysia Refining & Marketing Bhd PETRONAS Technical Services Sdn Bhd Shell Malaysia Trading Sdn Bhd SIRIM Berhad (Secretariat) Suruhanjaya Tenaga The Institution of Engineers, Malaysia Universiti Teknologi Malaysia Universiti Teknologi PETRONAS The Technical Committee on Petroleum Fuels which developed this Malaysian Standard consists of representatives from the following organisations:

Automobile Association of Malaysia Boustead Petroleum Marketing Sdn Bhd Caltex Oil (M) Limited Department of Environment Department of Occupational Safety and Health Malaysia Jabatan Pengangkutan Jalan Malaysia Malaysian Automotive Association Malaysian Palm Oil Board Ministry of Domestic Trade, Co-operatives and Consumerism PETRON Malaysia Refining and Marketing Berhad PETRONAS Dagangan Berhad PETRONAS Fuel Technology PETRONAS Group Technology Solutions Science and Technology Research Institute for Defence Shell (M) Trading Sdn Bhd Shell Global Solutions Malaysia Shell Refining Company (FOM) Berhad SIRIM Berhad (Secretariat) Universiti Kebangsaan Malaysia Universiti Teknologi Malaysia

Co-opted members:

European Union Malaysian Chamber of Commerce and Industry Malaysian Biodiesel Association PETRON Malaysia Refining and Marketing Berhad (Refinery)

For P

ublic

Com

ment

14H001R4

STANDARDS MALAYSIA 2014 - All right reserved iii

Foreword This Malaysian Standard was developed by the Technical Committee on Petroleum Fuels under the authority of the Industry Standards Committee on Petroleum and Gas. MS 123 consists of the following parts, under the general title Diesel fuel - Specification: Part 1: EURO 2M Part 2: EURO 4M Major modifications in this revision are as follow: a) Provision is made for a maximum of 7 % (v/v) of palm methyl ester (PME) to be included

in diesel fuel.

During the development of this standard, it is noted that specifications as recommended by ASEAN Automotive Federation cannot be fully adopted at this point of time.

This Malaysian Standard cancels and replaces MS 123-1:2005, Amd.1:2010 and Amd. 2:2012, Diesel fuel - Specification - Part 1: EURO 2M. . Compliance with a Malaysian Standard does not of itself confer immunity from legal obligations.

For P

ublic

Com

ment

14H001R4

STANDARDS MALAYSIA 2014 - All right reserved 1

Diesel fuel - Specification - Part 1: Euro 2M (Fourth revision)

1 Scope This Malaysian Standard specifies the requirements for diesel suitable for use in automotive, industrial and other diesel applications.

2 Normative references The documents and publications referred to in this standard are listed in Annex A.

3 Composition and properties 3.1 The diesel fuel shall consist of liquid hydrocarbons free from inorganic acid, grit, fibrous material and other foreign matters and shall meet the requirements in 3.2. It may contain small amounts of additives intended to improve some aspects of performance. 3.2 The diesel fuel shall comply with the requirements set out in Table 1 when tested by the methods indicated therein. 3.3 Palm Methyl Ester (PME)

Diesel fuel may contain up to 7 % (V/V) of PME complying with MS 2008. Refer to NOTE 2 of Table 1.

4 Sampling 4.1 Sampling from storage tanks Sampling of the material shall be carried out in accordance with the procedure described in ASTM D 4057. 4.2 Sampling from fuel lines 4.2.1 Sampling cans Sampling cans (tin-plated) shall be of 5 L and 1 L capacity. Their construction shall comply with the appropriate safety requirements for cans that are to hold highly flammable material. 4.2.2 Preparation of cans A stock of cans shall be kept solely for the purpose of taking fuel samples. Before use, all cans shall be checked to ensure that they are sound and free from leaks. A fuel-resistant sealing washer in good condition shall be positioned in the cap.

For P

ublic

Com

ment

14H001R4


4.2.3 Procedure Sampling can shall be rinsed with fuel from an offtake point. From the same offtake point, the fuel to be tested shall be carefully drawn into the sampling can using a clean dry funnel. The screw cap shall be fully tightened and the can is checked to ensure that there are no leaks. If more samples are needed, the operation shall be repeated immediately. 4.2.4 Labelling Full and legible information relating to the source of the sample shall be attached to the can in such a manner that it will not easily become detached subsequently.

5 Packing and marking 5.1 Packing 5.1.1 Containers The product shall be packed in suitable containers as agreed upon between the purchaser and the supplier. 5.1.2 Bulk The product shall be delivered in road tankers, rail wagons, barges, ocean tankers, pipelines or other means as agreed upon between the purchaser and the vendor, in accordance with the appropriate legal requirements. 5.2 Marking and labelling 5.2.1 Marking of pumps and containers The following information shall be clearly and indelibly marked on each dispensing pump or container used for delivering the diesel fuel in sales transaction: a) the name, brand, or trademark if any, of the producer, supplier or marketer; b) the name of the diesel fuel; and c) any other information as required by government regulations. 5.3 Certification mark Each product, may by arrangement with a recognised certification body, be marked with the certification mark of that body, provided the product conforms to the requirements of this standard.

For P

ublic

Com

ment

14

H001

R4

Table 1. General requirements for diesel fuel

Properties Minimum Maximum Referee test method

Colour (ASTM) - 2.5 ASTM D 1500

Ash, mass % - 0.01 ASTM D 482

Cloud point, C - 19.0 ASTM D 2500

Flash point, C 60 - ASTM D 93

Kinematic viscosity at 40 C, mm2/s 1.5 5.8 ASTM D 445

Copper corrosion (3 h at 100 C) - 1 ASTM D 130

Water by distillation, vol % - 0.05 ASTM D 95

Sediment by extraction, mass % - 0.01 ASTM D 473

Carbon residue on 10 % bottoms, mass % - 0.20 ASTM D 189

Density at 15 C, kg/l 0.810 0.870 ASTM D 1298

Acid number, mg KOH/g - 0.25 ASTM D 664

Electrical conductivity, pS/m 50 - ASTM D 2624

Cetane index

or

Cetane number

49

49

-

-

ASTM D 976

ASTM D 613

Physical distillation at 95 % recovered volume, C

or

Simulated distillation at 95 % recovered mass, C

-

-

370

399

ASTM D 86

ASTM D 2887

Lubricity, m - 460 ASTM D 6079

Total sulphur, mg/kg - 500 ASTM D 2622

No intentional additions of metallic additives are allowed.

NOTES:

1. Other test methods as specified in Annex B for determining the properties may be used, provided that they have been demonstrated to give the same degree of accuracy as the test methods listed. In the event of a dispute, the test method listed in this table is to be the referee method.

2. A suitable method for the separation and identification of FAME is given in EN 14331.

S

TA

ND

AR

DS

MA

LA

YS

IA 2

01

4 - A

ll right re

serv

ed 3

For P

ublic

Com

ment

14H001R4


Annex A (normative)

Normative references

The following normative references are indispensable for the application of this standard. For dated references, only the edition cited applies. For undated references, the latest edition of the normative references (including any amendments) apply. ASTM D 86, Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure ASTM D 93, Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester ASTM D 4057, Standard Practice for Manual Sampling of Petroleum and Petroleum Products ASTM D 130, Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test ASTM D 473, Standard Test Method for Sediment in Crude Oils and Fuel Oils by the Extraction Method ASTM D 189, Standard Test Method for Conradson Carbon Residue of Petroleum Products ASTM D 95, Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation ASTM D 445, Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) ASTM D 976, Standard Test Method for Calculated Cetane Index of Distillate Fuels ASTM D 2624, Standard Test Methods for Electrical Conductivity of Aviation and Distillate Fuels ASTM D 2622, Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry ASTM D 6079, Standard Test Method for Evaluating Lubricity of Diesel Fuels by the High-Frequency Reciprocating Rig (HFRR) ASTM D 1298, Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method ASTM D 613, Standard Test Method for Cetane Number of Diesel Fuel Oil ASTM D 97, Standard Test Method for Pour Point of Petroleum Products

For P

ublic

Com

ment

14H001R4


ASTM D 1500, Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale) ASTM D 664, Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration ASTM D 482, Standard Test Method for Ash from Petroleum Products ASTM D 2500, Standard test method for cloud point of petroleum products ASTM D 2887, Standard test method for boiling range distribution of petroleum fractions by gas chromatography

For P

ublic

Com

ment

14H001R4


Annex B (informative)

Alternative test methods Below is a listing of alternatives test methods for use with test requirements for Table 1

Table B1. Alternative test methods

Property Alternative test method

Colour (ASTM)

Cloud point, C

Carbon residue, mass %

Density at 15 C, kg/l

Total acid number, mg KOH/g

Cetane index

Cetane number

Total sulphur, mg/kg

Ash, mass%

Flash point, C

Kinematic viscocity at 40 C, cSt

Copper corrosion (3 hrs at 100 C)

Lubricity, m

ASTM D 6045

ASTM D 5772/ASTM D5771/IP 219

ASTM D 4530/IP13

ASTM D 4052

ASTM D 974

ASTM D 4737

ASTM D 6890/IP 498

ASTM D 4294/ASTM D 5453/

ASTM D 7039/IP 336

IP 4

IP 34

IP 71/ASTM D 7042

IP 154

IP 450

For P

ublic

Com

ment

14H001R4


Bibliography [1] EN 14078, Liquid petroleum products - Determination of fatty acid methyl ester (FAME)

content in middle distillates - Infrared spectrometry method [2] EN 14331, Liquid petroleum products - Separation and characterisation of fatty acid

methyl esters (FAME) from middle distillates - Liquid chromatography (LC)/gas chromatography (GC) method

[3] ASTM D 974, Standard test method for acid and base number by color-indicator

titration

[4] ASTM D 4052, Standard test method for density, relative density, and API gravity of liquids by digital density deter

[5] ASTM D 4294, Standard test method for sulfur in petroleum and petroleum products by energy dispersive X-ray fluorescence spectrometry

[6] ASTM D 4530, Standard test method for determination of carbon residue (Micro method)

[7] ASTM D 4737, Standard test method for calculated cetane index by four variable equation

[8] ASTM D 5453, Standard test method for determination of total sulfur in light hydrocarbons, spark ignition engine fuel, diesel engine fuel, and engine oil by ultraviolet fluorescence

[9] ASTM D 5771, Standard test method for cloud point of petroleum products (optical detection stepped cooling method)

[10] ASTM D 5772, Standard test method for cloud point of petroleum products (Linear

cooling rate method)

[11] ASTM D 5949, Standard test method for pour point of petroleum products (Automatic pressure pulsing method)

[12] ASTM D 5985, Standard test method for pour point of petroleum products (Rotational method)

[13] ASTM D 6045, Standard test method for color of petroleum products by the automatic tristimulus method

[14] ASTM D 6890, Standard test method for determination of ignition delay and derived cetane number (DCN) of diesel fuel oils by combustion in a constant volume chamber

[15] ASTM D 7039, Standard test method for sulfur in gasoline and diesel fuel by

monochromatic wavelength dispersive X-ray fluorescence spectrometry [16] ASTM D 7042, Standard Test Method for Dynamic Viscosity and Density of Liquids by

Stabinger Viscometer (and the Calculation of Kinematic Viscosity)

For P

ublic

Com

ment

14H001R4


Bibliography (continued) [17] ASTM D 737, Standard Test Method for Determination of Biodiesel (Fatty Acid Methyl

Esters) Content in Diesel Fuel Oil Using Mid Infrared Spectroscopy (FTIR-ATR-PLS Method)

[18] IP 4, Petroleum products - Determination of ash

[19] IP13, Petroleum products - Determination of carbon residue - Conradson method Section 2: Glass capillary kinematic viscometers - Specifications and operating instructions

[20] IP 34, Determination of flash point - Pensky-Martens closed cup method

[21] IP 71, Section 1: Petroleum products -Transparent and opaque liquids - Determination of kinematic viscosity and calculation of dynamic viscosity

[22] IP 154, Petroleum products - Corrosiveness to copper - Copper strip test

[23] IP 219, Petroleum products - Determination of cloud point

[24] IP 336, Petroleum products - Determination of sulfur content - Energy-dispersive-X-ray fluorescence method

[25] IP 450, Diesel fuel - Assessment of lubricity using the high-frequency reciprocating rig (HFRR) - Part I: Test Method

[26] IP 498, Determination of ignition delay and derived cetane number (DCN) of middle distillate fuels by combustion in a constant volume chamber

For P

ublic

Com

ment

STANDARDS MALAYSIA 2014 - All right reserved

Acknowledgements Members of Technical Committee on Petroleum Fuels Prof Dr Abu Bakar Mohamad (Chairman) Universiti Kebangsaan Malaysia Mr Chan Keng Sam (Deputy Chairman) Science and Technology Research Institute

for Defence Ms Zuraidah Baba (Secretary) SIRIM Berhad Mr Ahmed Ismail Amin Automobile Association of Malaysia Mr Tan Kwang Weng Boustead Petroleum Marketing Sdn Bhd Mr Philip Chee Caltex Oil (M) Limited Mr Ryan Ooi Department of Environment Mr Ahamad Yani Mohamad Department of Occupational Safety and

Health Malaysia Mr Azizul Abdul Aziz Jabatan Pengangkutan Jalan Malaysia Mr Liew Wei Jye Malaysian Automotive Association Mr Yung Chee Liang Malaysian Palm Oil Board Ms Masturah Abd Aziz Ministry of Domestic Trade, Co-operatives

and Consumerism

Mr Chew Choy/Mr Teh Hock Xiong PETRON Malaysia Refining and Marketing Berhad

Ms Ramona Nazreen Abdul Rahman/ Mr Mohamad Hafiz Abd Aziz

PETRONAS Dagangan Berhad

Mr Fazil Mat Isa/Mr Chan Ming Yau PETRONAS Fuel Technology Mr Abd Rahim Othman PETRONAS Group Technology Solutions Ir Loke Ean Bee/Mr Colin Chin Shell Global Solutions Malaysia Mr Ho Meng Tuck/ Mr Mahendran Subramaniam

Shell (M) Trading Sdn Bhd

Mr Peter Law Shell Refining Company (FOM) Berhad Assoc Prof Normah Mulop Universiti Teknologi Malaysia Co-opted members Mr Klaus Laudhaeusser Mr Frank Mccluskey

European Union Malaysian Chamber of Commerce and Industry

Ms Aiman Najati Akmar Rahman/ Ms Chan Yuen Teng

Malaysian Biodiesel Association

Mr Mohd Rizal Osman PETRON Malaysia Refining and Marketing Berhad (Refinery)

Documents

14H001R4_PC