16
28A/11, Ground Floor- Jia Sarai New Delhi 16 Ph.: 09811382221, 011-32662945 www.panaceainstitute.org.in 1 DO NOT OPEN THIS TEST BOOKLET UNTIL YOU ARE ASKED TO DO SO Test Booklet Series TEST BOOKLET Electronics & Communication Paper Topic Test Digital & Microprocessor Time Allowed: One Hour Maximum Marks: 100 INSTRUCTIONS 1. IMMEDIATELY AFTER THE COMMENCEMENT OF THE EXAMINATION YOU SHOULD CHECK THAT THIS TEST BOOKLET DOES NOT HAVE ANY UNPRINTED OR TORN OR MISSING PAGES OR ITEMS ETC. IF SO, GET IT REPLACED BY A COMPLETE TEST BOOKLET. 2. ENCODE CLEARLY THE TEST BOOKLET SERIES A, B, C, OR D AS THE CASE MAY BE IN THE APPROPRIATE PLACE IN THE ANSWER SHEET. 3. You have to enter your Roll Number on the Test Booklet in the Box provided alongside. DO NOT write anything else on the Test Booklet. 4. This Test Booklet contains 60 items (questions). Each item comprises four responses (answers). You will select the response which you want to mark on the Answer Sheet. In case you feel that there is more than one correct response, mark the response which you consider the best. In any case, choose ONLY ONE response for each item. 5. You have to mark all you responses ONLY on the separate Answer Sheet provided. See directions in the Answer Sheet. 6. All items carry equal marks. 7. Before you proceed to mark in the Answer Sheet the response to various items in the Test Booklet, you have to fill in some particulars in the Answer Sheet as per instructions sent to you with your Admission Certificate. 8. After you have completed filling in all your responses on the Answer Sheet and the examination has concluded, you should hand over to the Invigilator only the Answer Sheet. You are permitted to take away with you the Test Booklet. 9. Sheets for rough work are appended in the Test Booklet at the end. 10. Penalty for wrong answers: THERE WILL BE PENALTY FOR WRONG ANSWERS MARKED BY A CANDIDATE IN THE OBJECTIVE TYPE QUESTION PAPERS. (i) There are four alternatives for the answer to every question. For each question for which a wrong answer has been given by the candidate, one-third (0.33) of the marks assigned to that question will be deducted as penalty. (ii) If a candidate gives more than one answer, it will be treated as a wrong answer even if one of the given answers happens to be correct and there will be same penalty as above to that question. (iii) If a question is left blank, i.e., no answer is given by the candidate, there will be no penalty for that question DO NOT OPEN THIS TEST BOOKLET UNTIL YOU ARE ASKED TO DO SO

1371022526

Embed Size (px)

DESCRIPTION

aaaa

Citation preview

28A/11, Ground Floor- Jia Sarai New Delhi – 16 Ph.: 09811382221, 011-32662945 www.panaceainstitute.org.in 1

DO NOT OPEN THIS TEST BOOKLET UNTIL YOU ARE ASKED TO DO SO

Test Booklet Series

TEST BOOKLET

Electronics & Communication – Paper

Topic Test – Digital & Microprocessor

Time Allowed: One Hour

Maximum Marks: 100

INSTRUCTIONS

1. IMMEDIATELY AFTER THE COMMENCEMENT OF THE EXAMINATION YOU SHOULD

CHECK THAT THIS TEST BOOKLET DOES NOT HAVE ANY UNPRINTED OR TORN OR

MISSING PAGES OR ITEMS ETC. IF SO, GET IT REPLACED BY A COMPLETE TEST

BOOKLET.

2. ENCODE CLEARLY THE TEST BOOKLET SERIES A, B, C, OR D AS THE CASE MAY BE IN

THE APPROPRIATE PLACE IN THE ANSWER SHEET.

3. You have to enter your Roll Number on the

Test Booklet in the Box provided alongside.

DO NOT write anything else on the Test Booklet.

4. This Test Booklet contains 60 items (questions). Each item comprises four responses (answers). You

will select the response which you want to mark on the Answer Sheet. In case you feel that there is

more than one correct response, mark the response which you consider the best. In any case, choose

ONLY ONE response for each item.

5. You have to mark all you responses ONLY on the separate Answer Sheet provided. See directions in

the Answer Sheet.

6. All items carry equal marks.

7. Before you proceed to mark in the Answer Sheet the response to various items in the Test Booklet,

you have to fill in some particulars in the Answer Sheet as per instructions sent to you with your

Admission Certificate.

8. After you have completed filling in all your responses on the Answer Sheet and the examination has

concluded, you should hand over to the Invigilator only the Answer Sheet. You are permitted to take

away with you the Test Booklet.

9. Sheets for rough work are appended in the Test Booklet at the end.

10. Penalty for wrong answers:

THERE WILL BE PENALTY FOR WRONG ANSWERS MARKED BY A CANDIDATE IN THE

OBJECTIVE TYPE QUESTION PAPERS.

(i) There are four alternatives for the answer to every question. For each question for which a

wrong answer has been given by the candidate, one-third (0.33) of the marks assigned to that

question will be deducted as penalty.

(ii) If a candidate gives more than one answer, it will be treated as a wrong answer even if one

of the given answers happens to be correct and there will be same penalty as above to that

question.

(iii) If a question is left blank, i.e., no answer is given by the candidate, there will be no penalty

for that question

DO NOT OPEN THIS TEST BOOKLET UNTIL YOU ARE ASKED TO DO SO

28A/11, Ground Floor- Jia Sarai New Delhi – 16 Ph.: 09811382221, 011-32662945 www.panaceainstitute.org.in 2

Q.1. How many 0’s are present in binary representation of the expression

4 4096 9 257 7 17 4 9 1

(A) 7 (B) 8 (C) 9 (D) 10

Q.2. Consider bX (54) where b is the base of the number system. If X 7 then value of base ‘b’ is?

(A) 7 (B) 8 (C) 9 (D) Can’t be calculated

Q.3. Which of the following statement is not correct?

(A) XS-64 represents numbers from -64 to +63& XS-32 represents numbers from -32 to +31

(B) XS-64 represents numbers from -64 to +64& XS-32 represents numbers from -32 to +32

(C) XS-64 representation uses 7 bits while XS-32 representation uses 6 bits

(D) XS-3 code is self complementary and unweighted code

Q.4. In the logic equation A(A BC C) B(C A BC)(A BC AC) 1 If C A then which of the

following is true?

(A) A B 1 (B) A B 1 (C) A B 1 (D) A=1

Q.5. Which of the following statements are correct??

1. The sum of all min terms of a boolen function of n-variables is 1

2. The sum of all min terms of boolean functions of n-variables is 0

3. The product of all max-terms of a boolean functions of n-variables is 0

4. The product of all max-terms of a boolean functions of n-variables is 1

(A) 1, 3 (B) 1, 4 (C) 2, 3 (D) 2, 4

Q.6. Which of the following statement is not correct?

(A) Dual and Complement of EX-OR are EX-NOR&EX-NOR respectively

(B) f(A,B,C)=AB+BC+CA is a self dual expression

(C) Dual and Complement of EX-OR are EX-NOR&EX-OR respectively

(D) Max terms and Min terms are complement to each other

Q.7. Consider the logic function in Min terms form as f (A,B,C,D) (1,3,5,8,9,11,15) d(2,13) what

are the numbers of complemented literals in the expression of SOP form for f (A, B,C,D)?

(A) 3 (B) 4 (C) 5 (D) 6

Q.8. For a Boolean function Y AB AC the POS form will be:

(A) (0,2,4) (B) (1,2,5,7) (C) (2,3,5,7) (D) (0,2,4,5)

Q.9. What is the value of 1 2 3f (A,B,C) (f .f ) f if Min-terms of expressions are given as follows?

1

2

3

f (A,B,C) (0,2,3,4)

f (A,B,C) (1,2,3)

f (A,B,C) (4,5,6)

(A) (0,2,3,4) (B) (2,3,4,5,6) (C) (0,1,2,3,4,5,6) (D) (2,3)

Q.10. In a 8 variable K-Map if 32 number of 1’s are forming a group then number of literals in that group

after minimization will be?

(A) 3 (B) 4 (C) 5 (D) 6

28A/11, Ground Floor- Jia Sarai New Delhi – 16 Ph.: 09811382221, 011-32662945 www.panaceainstitute.org.in 3

v0

Q.11. Which of the following identity is not correct:

(A) A B C A (B C) (A B) C (B) A B C A (B C) (A B) C

(C) A B AB A B AB A B (D) A B C A (B C) (A B) C

Q.12. How many essential prime implicates are available in expression of f (A,B,C) (0,2,3,4,5,7)

(A) 0 (B) 3 (C) 5 (D) 6

Q.13. A 1 bit full adder takes 5 ns to generate carry out bit and 10 ns for the sum bit. What is the maximum

rate of addition per second when four 1-bit full adders are cascaded?

(A) 710 (B) 66.25 10 (C) 74 10 (D) 76.25 10

Q.14. Suppose only one multiplexer and one inverter are allowed to be used to implement any Boolean

function of n-variables. What is the Minimum size of Multiplexer needed??

(A) 2n-2

line to 1 line (B) 2n line to 1 line (C) 2

n+1 line to 1 line (D) 2

n-1 line to 1 line

Q.15. Which of the following statement is not correct?

(A) Half adder can be implemented by use of five two input NAND gate & five two input NOR gate

(B) Full adder can be implemented by use of nine two input NAND gate & nine two input NOR gate

(C) Half subtractor can be implemented by use of five two input NAND gate & five two input NOR

gate

(D) Half adder can be implemented by use of two 2:1 MUX (inverter is not available)

Q.16. Consider the following statements. A 4 × 16 decoder can be constructed with enable inputs by

1. Using 4, 2 × 4 decoders (each with enable input)

2. Using 5, 2 × 4 decoders (each with enable input)

3. Using 2, 3 × 8 decoders (each with enable input)

4. Using 2, 3 × 8 decoders (each with enable i/p & inverter)

Which statements are correct?

(A) Only 1 & 4 (B) Only 2 & 4 (C) Only 1 & 3 (D) Only 2 & 3

Q.17. Which of the following statement/s is/are correct?

1. The digital circuit using two inverters shown in figure will acts as Flip-flop

2. The digital circuit using five inverters shown in figure will acts as Ring counter.

(A) Only 1 (B) Only 2 (C) Both 1 & 2 (D) None

Q.18. A 5 bit serial adder is implemented using two 5 bit shift registers, a full adder and a D Flip-flop. The

two binary words to be added are 11011 and 11011.The sum of the two numbers is stored in one of

the shift registers and the carry in the D Flip-flop. Assuming that D Flip-flop is set initially the

contents of the sum shift register and D Flip-flop respectively are:

(A) 10111 and 0 (B) 11011 and 1 (C) 11101 and 0 (D) 10111 and 1

28A/11, Ground Floor- Jia Sarai New Delhi – 16 Ph.: 09811382221, 011-32662945 www.panaceainstitute.org.in 4

A

B

C

D

C J

K

B A

1

2-inputgate

C B A

J

K

J

K

Clockinput

D0 Q0 D1 Q1

Q1Q0

CLK

Q.19. In circuit shown in figure, when inputs A = B = 0, Then possible logic states of C & D are

(A) C = 0, D = 1 or C = 1, D = 0 (B) C = 1, D = 1 or C = 0, D = 0

(C) C = 1, D = 0 (D) C = 0, D = 1

Q.20. In the modulo-6 ripple counter shown in figure the output of the 2-input gate is used to clear the J-K

flip-flops.

The 2-input gate is:

(A) NAND gate (B) NOR gate (C) OR gate (D) AND gate

Q.21. In the circuit shown below initially

Q0 = Q1 = 0 Then what are the values of Q0 and Q1 after 335th

clock pulse.

(A) 00 (B) 01 (C) 10 (D) 11

Q.22. An X Y Flip-flop, whose characteristic table given below is to be implemented by use of a JK Flip-

Flop. This can be done by using

X Y Qn+1

0

0

1

1

0

1

0

1

1

Qn

Qn

0

( ) ( ) ( ) ( )A J X K Y B J X K Y C J Y K X D J Y K X

28A/11, Ground Floor- Jia Sarai New Delhi – 16 Ph.: 09811382221, 011-32662945 www.panaceainstitute.org.in 5

T0Q0

Q0

T1Q1

Q1

T2Q2

Q2

1

1 1

CLK

• • •S0 S1 S2

2R 2R 2R 2R

R Rv0

Q.23. Figure shows a ripple counter using positive edge triggered flip-flops. If the present state of the

counter is Q2 Q1 Q0 = 100 then its next state (Q2 Q1 Q0) will be:

(A) 011 (B) 100 (C) 111 (D) 101

Q.24. Which of the following statement is not correct?

(A) 4-bit ring counter requires 4 Flip-flops

(B)MOD-4 Johnson counter requires 4 Flip-flops

(C) MOD-4 Ring counter requires 4 Flip flops

(D) Both Ring and Jhonson counter are basically shift registers

Q.25. An R – 2R ladder type DAC is shown in Figure, if a switch status is ‘0’ then 0 volt is applied and if a

switch status is ‘1’ then 5 volt is applied to the corresponding terminal of DAC.

What is the step size of DAC?

(A) 0.125 V (B) 0.525 V (C) 0.625 V (D) 0.75 V

Q.26. Which of the following statement is not correct about ADC conversion time?

(A) Flash type ADC is the fastest ADC but conversion time depends upon no. of bits

(B) Counter type ADC has conversion time equal to N

c2 T where Tc is period of clock

(C) Successive approximation type ADC has conversion time equal to cN T where Tc is period of

clock

(D) Dual slope ADC is the slowest ADC and has the highest accuracy

Q.27. A combinational circuit accepts a 2 bit binary number and output is square in binary. To design this

circuit using a ROM the minimum size of ROM required is:

(A) 2 2 (B) 4 2 (C) 4 4 (D) 8 4

Q.28. For a given logic family if followings are the available data:

OH

IH

OL

IL

1.I (max) 4mA

2.I (max) 0.02mA

3.I (max) 8mA

4.I (max) 0.4mA

What is the value of Fan-out of given logic family:

(A) 10 (B) 20 (C) 200 (D) 400

28A/11, Ground Floor- Jia Sarai New Delhi – 16 Ph.: 09811382221, 011-32662945 www.panaceainstitute.org.in 6

A

B

VCC

y

• +5v

o/pAB

Q.29. If A and B are input as shown in figure and y is output then what is the value of y ??

(A) AB (B) ( )AB (C) (A + B) (D) ( )A B

Q.30.

In the I.C. logic gate shown in figure. If threshold voltage VBE is o.75 volt and VCE (sat) = 0.2 V

calculate value of output voltage. If VA = VB = 4.5 volt

(A) 0.75 V (B) 0.55 V (C) 5 V (D) 0.2 V

Q.31. Which of the following statement is not correct about 8085 Micro processor?

(A) It has 8bits data line and 16 bits address line

(B) Both address and data buses are multiplexed in this microprocessor

(C) Out of 16 address lines only lower order buses (A0-A7) are used as both data bus and address bus

(D) Both address bus and data bus of a micro processor are always bi-directional

Q.32. Which of the followings is not correct about various signal in 8085 Micro processor?

(A) ALE is positive going pulse and is used to latch lower order bus from multiplexed bus

(B) RD Indicates that selected I/O or memory device is to be read and data are available on data bus

(C) WR Indicates that data on data bus are to be written into a selected memory or I/O location

(D) S1 and S0 are status signals and deals with interrupt in 8085 microprocessor

Q.33. Which of the following statements are true about interrupt in 8085 microprocessor:

1. There are five interrupts in 8085 microprocessor

2. TRAP has the highest priority followed by RST 7.5, RST 6.5, RST 5.5 and INTR

3. All three RST and TRAP don’t require any external hardware i.e. they are automatically

transferred to specific locations without any hardware.

(A) 1 & 2 (B) 2 & 3 (C) 1 & 3 (D) 1, 2 & 3

28A/11, Ground Floor- Jia Sarai New Delhi – 16 Ph.: 09811382221, 011-32662945 www.panaceainstitute.org.in 7

Q.34. Which of the following statement is not correct about interrupt in 8085 Microprocessor

(A) TRAP is edge as well as level triggered interrupt

(B) RST 7.5 is positive edge triggered interrupt

(C) RST 6.5&RST 5.5 are level triggered interrupts

(D) RST 6.5&RST 5.5 are negative edge triggered interrupts

Q.35. Which of the following is not true about DMA transfer in microprocessor?

(A) It is direct transfer of data between memory and I/O devices without the use of microprocessor

(B) It is faster scheme for transfer of data from mass storage device & is also used for high speed

printers

(C) In burst mode DMA transfer I/O device withdraws request only after data bytes have been

transferred

(D) Cycle stealing scheme is same as burst mode transfer in DMA controller

Q.36. Which of the following statements are correct?

1. READY signal in 8085 is useful when the CPU communicates with a slow peripheral device

2. In a microprocessor wait states are used for interface of slow peripherals to the processor

3. READY signal is used to delay the microprocessor read or write cycles

4. READY pin is an output pin

(A) 1, 2 & 3 (B) 2, 3 & 4 (C) 1, 3 & 4 (D) 1, 2, 3 & 4

Q.37. Which of the followings are correct about INR and DCR instructions in 8085?

1. It affects contents of specified registers 2. It affects all flags except CY flag

3. Both INR and DCR are 2 byte instructions

(A) 1 & 2 only (B) 2 & 3 only (C) 1 & 3 only (D) 1, 2 & 3 only

Q.38. Which of the following is not true about registers in 8085 Microprocessor?

(A) Both SP and PC are 16 bit registers used in 8085 Microprocessor

(B) PC always holds address of the next instruction to be fetched

(C) SP always holds the address of the top of the stack

(D) Accumulator is also 16 bit register in 8085 Microprocessor which is used to perform arithmetic

and logical operations.

Q.39. A small code of 8085 as given below, is executed

MVI A, 7FH

ORA A

CPI A2H

The contents of the accumulator and flags after execution are

(A) A DD, S = 1, Z = 0, CY = 0 (B) A 7F, S = 1, Z = 0, CY = 1

(C) A DD, S = 0, Z = 1, CY = 0 (D) A 7F, S = 0, Z = 1, CY = 1

Q.40. Which of the following statement is not correct about status of flag register in 8085 Microprocessor?

(A) The value of MSB of result following the execution of any arithmetic or Boolean instruction is

stored in the sign status flag

(B) In execution of XRA A instruction zero flag is set

(C) In execution of instruction SUB B sign flag must not be affected

(D) In execution of instruction SUB B zero flag may be affected

28A/11, Ground Floor- Jia Sarai New Delhi – 16 Ph.: 09811382221, 011-32662945 www.panaceainstitute.org.in 8

Q.41. Which of the following pair is not correctly matched with regard to addressing mode?

(A) STA 2400H--------------- Direct addressing mode

(B) LXI H, 2500H------------Immediate addressing mode

(C) MVI A, 05-----------------Immediate addressing mode

(D) MOV A, B----------------- Register addressing mode

Q.42. The following sequences of instructions are executed by an 8085 microprocessor:

1000 LXI SP, 27 FF

1003 CALL 1006

1006 POP H

The contents of the stack pointer (SP) and the HL, register pair on completion of execution of these

Instructions are:

(A) SP = 27 FF, HL = 1003 (B) SP = 27 FD, HL = 1003

(C) SP = 27 FF, HL = 1006 (D) SP = 27 FD, HL = 1006

Q.43. Consider the sequence of 8085 instruction given below:

LXI H, 9258

MOV A, M

CMA

MOV M, A

Which one of the following is performed by this sequence?

(A) Contents of location 9258 are moved to the accumulator

(B) Contents of location 9258 are compared with the contents of the accumulator

(C) Contents of location 9258 are complemented and stored in location 9258

(D) Contents of location 5892 are complemented and stored in location 5892

Q.44. In the following 8085 program how many times (decimal) is the DCRC executed?

MVIC, 78 H

LOOP DCRC

JNZ LOOP

HLT

(A) 119 (B) 120 (C) 78 (D) 77

Q.45. Match List-I with List-II and select the correct answer using the code given below the Lists:

List-I List-II

A. 8255A 1. Programmable Peripheral Interface

B. 8279 2. Programmable Interval Timer

C. 8254/8253 3. DMA Controller

D. 8237/8257 4. Programmable Keyboard/Display Interface

Code: A B C D A B C D

(A) 2 4 1 3 (B) 1 3 2 4

(C) 2 3 1 4 (D) 1 4 2 3

Q.46. Which one of the following is used as the interface chip for data transmission between 8086 and a

16-bit ADC?

(A) 8259 (B) 8255 (C) 8253 (D) 8251

28A/11, Ground Floor- Jia Sarai New Delhi – 16 Ph.: 09811382221, 011-32662945 www.panaceainstitute.org.in 9

Q.47. Match List-I with List-II and select the correct answer using the code given below the Lists :

List – I List – II

(Program Required in (Definition)

System Software)

A. Linker 1. It is a program which combines smaller programs to

form a single program; and also links subroutines with the

main program

B. Loader 2. It is a program which loads machine codes of a program into

the system memory?

C. Interpreter 3. It is a program which translates a high-level program into

machine code executes it and reads one statement at a time,

executes and then goes to the next statements of the program

D. Compiler 4. It is a program which translates a high-level program into a

machine language, Reads the entire program and then

executes it

Code: A B C D A B C D

(A) 1 2 3 4 (B) 3 4 1 2

(C) 1 4 3 2 (D) 3 2 1 4

Q.48. Which of the following statements are correct about 8086 Microprocessor?

1. It is 16 bit microprocessor and is 40 pin package

2. There are 14 general purpose registers

3. There are 9 flag registers

4. It is capable of addressing 2 M bytes of memory

(A) 1 & 2 (B) 1, 2 & 3 (C) 1, 3 & 4 (D) 1, 2, 3 & 4

Q.49. In a 8085 microprocessor, the following sequence of instructions is executed.

STC

CMC

MOV A, B

RAL

MOV B, A

After the last instruction the output will

(A) Rotate the contents of the accumulator and store it in B

(B) Get the contents of B register into accumulator and rotate it to left by one bit

(C) Double contents of B register (D) manipulate carry in A and B

Q.50. If (BX) = 0158

(DI) = 10A5

Displacement = 1B57

(DS) = 2100

(Where DS is used as a segment register) then the effective and physical addresses produced using

“RELATIVE BASE” INDEXED INDIRECT ADDRESSING” will be respectively

(A) 2D54 and 23D54 (B) 23D54 and 2D54 (C) 1B57 and 1CAF (D) 1CAF and 1B57

28A/11, Ground Floor- Jia Sarai New Delhi – 16 Ph.: 09811382221, 011-32662945 www.panaceainstitute.org.in 10

Q.51. Which of the following statement is not correct about Cache memory?

(A) Cache memory is based upon concept of locality of reference

(B) Performance of cache memory is measured in terms of hit ratio

(C) Cache memory is fast but costly memory

(D) Size of cache memory is very large

Q.52. Which of the following statements are correct about various registers?

1. The register which contains the instruction to be executed is called as Index register

2. The register which keeps track of execution of a program and which contains the memory

address of instruction currently being executed is called as Program counter

3. The register which hold address of location to or from which data are to be transferred is known

as Memory Address Register (MAR)

4. The register which contains the data to be written into or readout of location is known as

Memory Buffer Register (MBR)

(A) 1, 2 & 3 (B) 2, 3 & 4 (C) 1, 3 & 4 (D) 1, 2, 3 & 4

Q.53. What is the depth of a complete binary tree with n nodes?

(A) log2(n + 1) – 1 (B) log2(n – 1) + 1 (C) log2(n) + 1 (D) log2(n) – 1

Q.54. Given that main memory access time is 1200 ns and cache access time is 100 ns if the average

memory access time is not to exceed 120 ns. The hit ratio for the Cache must be at least:

(A) 90% (B) 98% (C) 80% (D) 75%

Q.55. Which of the following are included in the architecture of computer?

1. Addressing modes, design of CPU

2. Instruction set, data formats

3. Secondary memory, operating system

Select the correct answer using the codes given below:

Codes: (A) 1 and 2 (B) 2 and 3 (C) 1 and 3 (D) 1, 2 and 3

Q.56. How many distinct binary trees can be constructed with three nodes?

(A) 1 (B) 2 (C) 3 (D) 5

Q.57. A sub routine can return:

(A) Only one value (B) only two values (C) Only three values (D) any no of values

Q.58. Match List-I (Type of Data Structure) with List-II (Used in Application) and select the correct

answer using the codes given below the lists:

List-I List-II

(Type of data Structure) (Used in Application)

A. Stack 1. Solving linear simultaneous equations

B. Tree 2. Subroutine linkage

C. Record 3. File processing

D. Array 4. Sorting

Codes: A B C D A B C D

(A) 3 4 2 1 (B) 2 1 3 4

(C) 2 4 3 1 (D) 3 1 2 4

28A/11, Ground Floor- Jia Sarai New Delhi – 16 Ph.: 09811382221, 011-32662945 www.panaceainstitute.org.in 11

Q.59. The default parameter passing mechanism in C programming language is:

(A) Call by reference (B) Call as random

(C) Call by values (D) Call by value result

Q.60. IC is the Instruction Count, CPI is average number of system clock periods to execute per instruction

and T is the duration of a clock period then which one of the following expresses execution time?

(A) IC CPI T (B)

IC CPI

T

(C) IC T

CPI

(D)

T CPI

IC

28A/11, Ground Floor- Jia Sarai New Delhi – 16 Ph.: 09811382221, 011-32662945 www.panaceainstitute.org.in 12

Engineering Service Examination -2013

SI No.

Electronics & Telecommunication Engineering

PAPER – Digital Electronics & Microprocessor

(Conventional)

Time allotted: 90 Minute Maximum marks: 100

INSTRUCTIONS

Candidates should attempt Question No. 1 which is compulsory and remaining FOUR from questions taking

two each from section-A and Section-B. The number of marks carried by each question is indicated at the

end of the question. Answers must be written only in English. Assume suitable data if found necessary and

indicate the same clearly. Values of the following constants may be used wherever necessary:

Electronic charge = –1.6 × 10–9

Coulomb

Free space permeability = 4 × 10–7

Henry /m.

Free space permittivity = 9110

36

Farad/m.

Velocity of light in free space = 3 × 108 m/ sec.

Boltzmann constant = 1.38 × 10–23

joule /K.

Planck constant = 6.626 × 10–34

joule-sec.

Important: Candidates are to note that all parts and sub parts of a question are to be attempted

continuously in answer book. That is all parts and sub parts of a question being attempted must be

completed before attempting the next question.

Any page left blank in answer book must be clearly struck out. Answers that follow pages left blank

may not be given credit.

28A/11, Ground Floor- Jia Sarai New Delhi – 16 Ph.: 09811382221, 011-32662945 www.panaceainstitute.org.in 13

Q.1. (a) The 4 × 1 MUX is shown in figure what is the value of output f(x, y, z) (5)

(b) Draw the circuit of a 3-bit parallel comparator analog to digital converter. Compare the speed and

hardware requirement of flash ADC, successive approximation ADC, counter type ADC and dual

slope ADC (5)

(c) For the given synchronous counter what is the MOD of given counter? (5)

(d) Determine the don’t care combinations in the following Boolean expression: ,BE BDE which

is a simplified version of expression : .ABE BCDE BCDE ABDE BCDE (5)

(e) What are the function of the following pins of 8085 microprocessor (5)

(i) READY (ii) ALE (iii) HOLD (iv) TRAP (v) HLDA

(f) Distinguish between (5)

(i) High Level Language and Low Level Language

(ii) Macro Programming and Micro-Programming

(iii) Machine Cycle and Instruction Cycle

(iv) Hardware Interrupts and Software Interrupts

(v) Memory mapped I/O and I/O mapped I/O.

(g) A memory system contains a cache, a main memory and a virtual memory. The access time of

the cache is 5 ns and it has an 80 percent hit rate. The access time of the main memory is 100 ns

and it has a 995 percent hit rate. The access time of the virtual memory is 10 ms. what is the

average access time of the hierarchy? (5)

(h) An 8085 assembly language program is given below. (5)

Line 1: MVI A, B5H 2: MVI B, 0EH

3: XRI 69 H 4: ADD B

5: ANI 9BH 6: CPI 9FH

7: STA 3010H 8: HLT

(i) The contents of the accumulator just after execution of the ADD instruction in line 4 will be:

(ii) After execution of line 7 of the program, the status of the CY and Z flags will be:

28A/11, Ground Floor- Jia Sarai New Delhi – 16 Ph.: 09811382221, 011-32662945 www.panaceainstitute.org.in 14

A S

Ci

B

FULLADDER

C0

Q D

CK

D Q

CK

D Q

CK

1 0 1 1

0 0 1 1

MSB LSB

Shift Registers

Clock

SECTION-A

Q.2. (a) Design Mod-6 Ripple Down counter by use of FFS and NAND gates (5)

(b) Design Mod-8 Synchronous up counter by use of FFS and gates (5)

(c) Convert D FF into T FF by K-Map method (5)

Q.3. (a) Draw NAND gate and NOR gate by use of CMOS (10)

(b) Design Positive logic OR and Negative OR gate by use of diodes (5)

Q.4. (a) Construct a 4-input multiplexer using four 3-input AND gates, an OR-gate and three inverters.

Show the input, output and select lines and write a table showing the outputs for various select

inputs. (10)

(b) For the circuit shown in figure below, two 4-bit parallel in serial-out shift registers loaded with

the data shown are used to feed the data to a full adder. Initially all the flip-flops are in clear

state. After applying two clock pulses, the outputs of the full adder should be (5)

28A/11, Ground Floor- Jia Sarai New Delhi – 16 Ph.: 09811382221, 011-32662945 www.panaceainstitute.org.in 15

256 bytes

Chip # 1

A –A0 7

A8

A9

A9

A8

256 bytes

Chip # 2

A –A0 7

A –A10 16not used

SECTION-B

Q.5. (a) Write an 8085 ALP to find smallest number in an Array. (10)

(b) What memory address range is represented by chip #1& chip #2 in figure? A0 to A15 in this

figure are the address lines and CS means Chip Select. (5)

Q.6. The contents of some memory locations of an 8085 microprocessor system are show below. What

will be the contents of H-L Pair after the execution of the program given below. (15)

LHLD 3000H

MOV E, M

INX H

MOV D, M

LDAX D

MOV L, A

INX D

LDAX D

MOV H, A

Memory address Memory contents

(Hex) (Hex)

3000 02

3001 30

3002 00

3003 30

Q.7. (a) Give the number of bytes, Machine cycles and T state for the following opcodes used in 8085

Micro Processor. (5)

(i) LDA

(ii) JMP

28A/11, Ground Floor- Jia Sarai New Delhi – 16 Ph.: 09811382221, 011-32662945 www.panaceainstitute.org.in 16

(iii) POP

(iv) STA

(v) STAX

(b) What are execution unit and bus interface unit in case of 8086 Microprocessor explain with

proper diagram. what is the difference between 8086 and 8088 microprocessor? (10)