Upload
vantram
View
223
Download
0
Embed Size (px)
Citation preview
D10
0118
X01
2
Bulletin 71.1:133June 2013
www.fisherregulators.com
Features • Wide Pressure Range Capability with Single Regulator—Type 133H may also use Type 133L springs, allowing pressure settings to be varied between 2 inches w.c. and 10 psig / 5 mbar and 0.69 bar by changing springs.
• Types 133L, 133H, and 133HP Suitable for Monitoring Applications—O-ring stem seal on Types 133L, 133H, and 133HP isolates body pressure from controlled pressure.
• Excellent Shock Characteristics and Fast Speed of Response—Due to two-way stabilizer vent valve, which vents the spring case more rapidly than conventional vents, lag in diaphragm and valve disk movement is minimized.
• Bubble-Tight Shutoff—Single-port construction, large diaphragm area, and light-rate springs along with disk material and seat design provide low lock-up pressures.
• Spring and Diaphragm Effects Minimized—Boosting system provides excellent performance
overawiderangeofflowconditions.
• No Seat-to-Seat Adjustment Required—Balanced single-port design eliminates necessity for seat-to- seat adjustments to achieve bubble-tight shutoff.
• Easy Access to Trim Parts—Valve seat, disk, and cage easily removed with body remaining in line andwithoutdisassemblyofactuatorportion;orifice is not threaded in.
• Reusable Pressure Seals—O-rings used for pressure seals, unlike gaskets, are not ordinarily damaged by disassembling the regulator.
• Resistance to Piping Stresses—Steel constructions are available to help resist pipe stresses.
133 Series Direct-Operated Regulators
W1327/IL
TYPES 133H, 133L, AND 133Z REGULATORS TYPE 133HP REGULATORTYPE 133HP REGULATOR
W6803/IL
Figure 1. 133 Series Direct-Operated Regulators
Bulletin 71.1:133
2
Available Constructions Type 133H: Direct-operated regulator for inlet pressures to 60 psig / 4.1 bar and outlet pressures from 1.5 to 10 psig / 0.10 to 0.69 bar, three ranges. Type 133HP: Direct-operated regulator for inlet pressures to 150 psig / 10.3 bar and outlet pressures from 2 to 60 psig / 0.14 to 4.1 bar, seven ranges. Type 133L: Direct-operated regulator for inlet pressures to 60 psig / 4.1 bar and outlet pressures from 2 inches w.c. to 2 psig / 5 mbar to 0.14 bar, six ranges. Type 133Z Zero Governor: Direct-operated regulator for inlet pressures to 20 psig / 1.4 bar and outlet pressures from -1 to 4-inches w.c. / -2.5 to 10 mbar, two ranges.
Body Size and End Connection StylesBODY SIZE BODY MATERIAL
Inch DN Cast Iron Body WCC Steel Body
2 50 NPT or CL125 FF Flanged NPT or CL150 RF Flanged
Maximum Inlet Pressures(1)
See Table 2 Outlet Pressure Ranges(1)
See Table 1Maximum Outlet Pressures(1)
See Table 2Pressure Registration External; downstream control line is requiredControl Line Connection Types 133H, 133L, and 133Z: 3/4 NPT internal connection will be positioned directly over body outlet (standard position) or 90° right or left ofstandardpositionifspecified. Type 133HP: 1/4 NPT Internal connection positioned directly over body outlet.Vent Connection Types 133H, 133L, and 133Z: 1 NPT internal with screen; standard position is in line with control line connection directly over body outlet. Vent will always be positioned over the control line connection. Type 133HP: 1/2 NPT internal connection positioned directly over body inlet with a Fisher® Type Y602-7 vent assembly.
SpecificationsTheSpecificationssectionliststhespecificationsfortheType133Seriesdirect-operatedregulators.Factoryspecificationisstampedonthenameplatefastenedontheregulatoratthefactory.
Temperature Capabilities(1)
-20 to 150°F / -29 to 66°CFlow Capacities See Tables 3 through 10Wide-Open Flow Coefficients
CAPACITY WIDE-OPEN Cg FORRELIEF VALVE SIZING
REPRESENTATIVEC1
25%(2)
40%(2)
60%(2) 100%
49076011501800
28.229.131.835.0
Construction Materials Body: Cast iron or WCC Steel Orifice and Cage: Aluminum Valve Disk: Aluminum/Neoprene (CR) or Aluminum/Fluorocarbon (FKM)(3)
O-rings: Nitrile (NBR) or Fluorocarbon (FKM)(3)
Diaphragms: Nitrile (NBR)/Nylon (PA) (Neoprene (CR) in actuator) or Fluorocarbon (FKM)(3)/Polymer Thermoplastic Guide Bushing: Nylon (PA) Stem and Stem Sleeve: Stainless steel Diaphragm Plate: Steel Balancing Diaphragm Plate: Plated steel Spring Case and Closing Cap: Type 133HP: Cast Iron Types 133H, 133L, and 133Z: Aluminum Lower Casing: Types 133H, 133L, and 133Z: Aluminum Type 133HP: Steel Adjusting Screw: Types 133H and 133Z: Brass Type 133L: Aluminum Type 133HP: Steel Optional Restriction Collar: AluminumApproximate Shipping Weight Types 133H, 133L, and 133Z NPT End Connections: 35 pounds / 16 kg Types 133H, 133L, and 133Z Flanged End Connections: 40 pounds / 18 kg Type 133HP NPT End Connections: 56.5 pounds / 26 kg Type 133HP Flanged End Connections: 62.5 pounds / 28 kgOption Restriction collar to reduce wide-open capacity to approximately 25%, 40%, or 60% of standard wide-open capacity.
1. The pressure/temperature limits in this Bulletin or any applicable standard limitation should not be exceeded. 2. Using optional restriction collar. 3. Available for Types 133L and 133H only.
Bulletin 71.1:133
3
W1213-1/IL
TYPE 133Z ZERO GOVERNOR
Figure 2. Types 133Z, 133L, and 133H Regulators
1 IDENTIFICATION GROOVES:25% CAPACITY COLLAR—NO GROOVES40% CAPACITY COLLAR—ONE GROOVE60% CAPACITY COLLAR—TWO GROOVES
W1212-1/IL
TYPE 133L LOW-PRESSURE REGULATOR
TRIM PARTS WITH RESTRICTION COLLAR(40% CAPACITY COLLAR IS SHOWN)
SET SCREW
CAGE
VALVE DISKE-RING
IDENTIFICATION GROOVE
ORIFICE1
W2215-1
TYPE 133H WITHOUTRESTRICTION COLLAR
W1211-1
RESTRICTION COLLAR
Bulletin 71.1:133
4
Introduction
DescriptionThe 133 Series direct-operated gas regulators, shown in Figure 1 are primarily designed for industrial and commercial applications supplying gas to furnaces, burners, and other appliances. The 133 Series balancing system enables the regulator to provide accurate control of gas pressure for maximum combustionefficiencydespitevaryinginletpressureconditions. The single port construction provides bubble-tight shutoff. An external downstream control line is required for the operation of the regulator. Refer to Table 1 for outlet pressure ranges of each type. 133 Series regulators are available in a 2 inch / DN 50 bodysizewitheitherNPTorflangedendconnections.
An optional restriction collar (Figure 2) can be installed if wide-open capacity is too high for applications using a relief valve as overpressure protection. The collar reduces wide-open capacity to 25%, 40%, or 60% of standard wide-open capacity.
Principle of OperationRefer to the operational schematics in Figure 4. In the 133 Series, downstream pressure is registered under the diaphragm via the external control line and is used as the operating medium. Increased demand lowers the downstream pressure and allows the spring to move the diaphragm and stem assembly down, opening the valve disk and supplying more gas to the downstream system. Decreased demand increases the downstream pressure and moves the diaphragm and stem assembly up, closing the valve disk and decreasing the gas supply to the downstream system.
Boosting SystemThe 133 Series incorporates a balancing diaphragm and a boosting system. When the regulator is locked up, inlet pressure is registered on the top of the valve disk and on the bottom of the balancing diaphragm through registration holes in the top of the cage. Also, downstream pressure is registered on the bottom of the valve disk and on the top of the balancing diaphragm through a passage formed by grooves in the registration disk and an annular space between the stem and stem sleeve.
Whenthevalvediskisopen,gasflowsfromtheinletover the edge of the valve disk to the outlet. Under the valve disk near the registration disk, there is little
gasflow.Thegaspressureneartheregistrationdiskishigherthanitisintheflowpathwheregasvelocitytends to lower the pressure. The higher pressure near the disk is registered on the top of the balancing diaphragm through the registration disk and the annular space between the stem and stem sleeve.
This pressure registered on the top of the balancing diaphragm aids downward disk travel and compensates for spring and diaphragm effect. This improves regulator rangeability and performance.
Two-Way Stabilizer Vent Valve on Types 133H, 133L, and 133Z When the regulator responds to an increase in downstream pressure, the diaphragm moves upward. As the diaphragm rises, movement of air forces the lower vent stabilizer upward, carrying the upper stabilizer with it (see Figure 5). This allows the air above the diaphragm to vent to atmosphere rapidly enough to minimize lag in diaphragm movement.
Asthediaphragmfalls,airrushesintheventtofillthe partial vacuum created, forcing the upper vent
W6883/IL
Figure 3. Type 133HP Regulator
Bulletin 71.1:133
5
Type 133L
A65
55
July 2009 Type 133L
BALANCINGDIAPHRAGM
REGISTRATION DISK
A6555 A6883
TYPE 133L REGULATOR
Figure 4. Operational Schematics
stabilizeragainsttheorificeplate.Airflowingthroughthe webs of the upper stabilizer opens the lower stabilizer (see Figure 5). With the regulator at steady-state conditions, both stabilizers are closed and only a small hole is open to help stabilize normal operation.
InstallationThe regulator may be installed in any position but is normally installed with the actuator portion vertical above the body portion. Flow through the body must beinthedirectionindicatedbytheflowdirectionarrowcast on the body portion. A downstream control line is required for operation of the regulator.
A remote vent line may be required for some installations. Vent openings must be protected against the entrance of rain, snow, insects, or any other foreign material that may plug the vent.
External dimensions are shown in Figure 9.
Overpressure ProtectionAs is the case with most regulators, the 133 Series regulators have outlet pressure ratings that are lower than the inlet pressure ratings. Some type of Overpressure Protection is needed if the actual inlet pressure ever exceeds the outlet pressure rating.
Maximum inlet and outlet pressures for the 133 Series are given in Table 2. All models must be protected against inlet pressure above the maximum emergency inlet pressure (refer to Table 2).
Outlet pressure more than 3 psig / 0.21 bar for Types 133H, 133L, and 133Z, or 40 psig / 2.8 bar for Type 133HP over the outlet pressure setting of the regulator may damage internal parts such as the diaphragm plate and valve disk.
Regulator operation below these emergency pressure limitations does not preclude the possibility of damage
Type 133HP
A68
83
June 2009 Type 133HP
INLET PRESSUREOUTLET PRESSUREATMOSPHERIC PRESSUREBOOST PRESSURE
INLET PRESSUREOUTLET PRESSUREATMOSPHERIC PRESSURE
INTERMEDIATE PRESSUREPILOT SUPPLY PRESSUREVACUUM PRESSURETANK PRESSUREVAPOR PRESSURE
LOADING PRESSURE
RELIEF PRESSUREBOOST PRESSURE
TYPE 133HP REGULATOR
CONTROL SPRING
DOWNSTREAM CONTROL LINE
VALVE DISK
ORIFICESTEM
DIAPHRAGM
VENT ASSEMBLY
DOWNSTREAM CONTROL LINE
DIAPHRAGM
INLET PRESSURE
OUTLET PRESSURE
ATMOSPHERIC PRESSURE
BOOST PRESSURE
INLET PRESSURE
OUTLET PRESSURE
ATMOSPHERIC PRESSURE
BOOST PRESSURE
Bulletin 71.1:133
6
from external sources or from debris in the gas line. The regulator should be inspected for damage after any overpressure condition. Complete instructions for installation, operation, and maintenance are provided with each regulator.
Capacity DataFlow capacities for various inlet pressures and outlet pressure settings are shown in Tables 3 to 10. Capacities are in thousands of SCFH at 60°F and 14.7 psia and in thousands of Nm3/h at 0°C and 1.01325barof0.6specificgravitygas.Toconvert
to equivalent capacities of other gases, multiply the SCFH values shown by the appropriate factor: air–0.775; propane–0.628; butane–0.548; nitrogen–0.789. Forgasesofotherspecificgravities,multiplythegivencapacity by 0.775, and divide by the square root of theappropriatespecificgravity.Then,ifcapacityisdesired in Nm³/h at 0°C and 1.01325 bar, multiply SCFH by 0.0268.
Note
For optimum performance, select the lowest spring range that includes the desired outlet pressure setting.
Table 1. 133 Series Outlet Pressure Ranges, Control Springs
Table 2. Maximum Inlet and Outlet Pressures
PRESSURESTYPE NUMBER
133H 133HP 133L 133Zpsig bar psig bar psig bar psig bar
Maximum Operating Inlet Pressure 60 4.1150 10.3
60 4.1 20 1.4
Maximum Emergency Inlet Pressure 125 8.6 125 8.6 125 8.6
Maximum Operating Outlet Pressure(1) 10 0.69Setpoint plus 40
Setpoint plus 2.8
2 0.14 4 inches w.c. 10 mbar
Maximum Outlet Pressure OverOutlet Pressure Setting 3 0.21 3 0.21 3 0.21
Maximum Emergency Outlet(Casing) Pressure 15 1.0 150 10.3 15 1.0 15 1.0
1. With highest spring range available only.
TYPEOUTLET PRESSURE RANGE CONTROL SPRINGS
psig bar Part Number Color CodeFree Length Wire Diameter
Inch mm Inch mm
133H(1)1.5 to 32 to 5
5 to 10
0.10 to 0.210.14 to 0.340.34 to 0.69
1H97592703210A9440X0121J146927142
OrangeYellowBlue
6.916.476.19
176164157
0.2500.2830.375
6.357.199.53
133HP(1)
2 to 54.5 to 106 to 20
16 to 3026 to 4036 to 5045 to 60
0.14 to 0.340.31 to 0.690.41 to 1.41.1 to 2.11.8 to 2.82.5 to 3.43.1 to 4.1
17B8632X01217B8633X01210C1238X01210C1240X01210C1241X01210C1242X01210C1243X012
YellowOrangeSilverRedBlue
GreenWhite
8.58.5
8.258.258.258.258.25
216216210210210210210
0.2820.3430.3750.4380.5000.5000.531
7.168.719.5211.112.712.713.5
133L(1) and 133H(2)
2 to 4 inches w.c.3.5 to 6 inches w.c.5 to 9 inches w.c.
8.5 to 18 inches w.c.14 to 28 inches w.c.
0.75 to 2
5 to 10 mbar9 to 15 mbar
12 to 22 mbar21 to 45 mbar35 to 70 mbar0.05 to 0.14
1D8925270221D8926270221D8927270121D8932270321D8933270321H975827032
BrownRed
BlackWhiteGreenBlue
6.137.537.887.5
7.257.09
156191200191184180
0.1090.1120.1300.1560.1820.225
2.772.843.303.964.625.72
133Z(1)
-1 to 1 inch w.c. -3 to 3 mbar 1K633427012(Extension Spring) Unpainted 2 50.8 0.075 1.91
0 to 4 inches w.c. 0 to 10 mbar
1K633427012(Extension Spring)
and1D892527022
(Compression Spring)
Unpainted
Brown
2
6.13
50.8
156
0.075
0.109
1.91
2.77
1. Pressure ranges shown are correct if the regulator is installed with the actuator portion above the body portion. If the regulator is installed with the actuator portion below the body, the pressure ranges will be lowered by approximately 2 inches w.c. / 5 mbar for the Type 133L and by approximately 3 inches w.c. / 7 mbar for the Types 133H and 133Z. 2. If the 2 inches w.c. / 5 mbar to 2 psig / 0.14 bar springs (all 6 ranges) are used in the Type 133H, the pressure ranges will increase by approximately 1 inch w.c. / 2 mbar due to the weight of the Type 133H parts (assuming that the actuator is installed above the body).
Bulletin 71.1:133
7
Forrestricted-capacityconstructions,determineflowcapacities for outlet pressure settings of 2 psig / 0.14 bar or less by multiplying the values from Tables 3 to 10 by 25%, 40%, or 60% (depending upon which restriction collar is selected). For pressure settings over 2 psig / 0.14 bar, capacities are given inTable6.Ifflowcapacitiesforinletpressureslower than those shown are required, contact your localSalesOffice.TherepresentativeregulatingCg of 1650 may be used for regulator sizing of full capacity constructions only if capacity table data is not available. The representative regulating Cg is an approximation only for pressure drops greater than 5 psi / 0.34 bar, because, at a given offset in controlled pressure, the regulating Cg varies with the spring being used with the pressure drop across the valve.TodeterminecapacityusingtheflowcoefficientCg, use the appropriate procedure below.
Critical Pressure Drops For critical pressure drops (absolute outlet pressure equal to or less than one-half of absolute inlet pressure), use the following formula:
Q = (P1)(Cg)(1.29)
Non-Critical Pressure DropsFor pressure drops lower than critical (absolute outlet pressure greater than one-half of absolute inlet pressure).
Q = CgP1SIN520GT
3417C1
∆PP1
DEG
where,
Q =gasflowrate,SCFH P1 = absolute inlet pressure, psia (P1 gauge + 14.7) Cg =regulatingorwide-opengassizingcoefficient G =specificgravityofthegas T = absolute temperature of gas at inlet, °Rankine C1 =flowcoefficient
P = pressure drop across the regulator, psi
W1032-1/IL
TWO-WAY STABILIZER VENT VALVE IN “UP” POSITION AS DIAPHRAGM RISES
Figure 5. Types 133H, 133L, and 133Z Stabilizer Vent
VENT VALVE IN “DOWN” POSITION AS DIAPHRAGM LOWERS
W1902-1/IL
Table 3. Full-Capacity Type 133Z Regulated Flow in Thousands of SCFH of 0.6 Specifi c Gravity Gas at 14.7 psia and 60°F
INLET PRESSURE1 inch w.c. / 3 mbar OUTLET PRESSURE SETTING(1) (EITHER SPRING RANGE)0.5 inch w.c. / 1 mbar Droop 1 inch w.c. / 3 mbar Droop
psig bar SCFH Nm3/h SCFH Nm3/h8 inches w.c. 14 inches w.c.
12
20 mbar35 mbar
0.070.14
2.44.16.511.5
0.060.110.170.31
5.17.41218
0.140.200.320.48
51020
0.340.691.4
224476
0.591.182.04
325078
0.861.342.09
1. Outlet pressure setting was made at approximately 10% of the maximum capacity for the listed conditions.
Bulletin 71.1:133
8
Table 4. Full-Capacity Type 133L Regulated Flow in Thousands of SCFH of 0.6 Specific Gravity Gas at 14.7 psia and 60°F
Table 5. Full-Capacity Type 133H Regulated Flow in Thousands of SCFH of 0.6 Specific Gravity Gas at 14.7 psia and 60°F
INLETPRESSURE
OUTLET PRESSURE SETTING(1), SPRING PART NUMBER, AND OUTLET PRESSURE RANGE
3 psig / 0.21 bar1H9759270321.5 to 3 psig /
0.10 to 0.21 bar
2 psig / 0.14 bar10A9440X0122 to 5 psig /
0.14 to 0.34 bar
5 psig / 0.34 bar10A9440X0122 to 5 psig /
0.14 to 0.34 bar
5 psig / 0.34 bar1J1469271425 to 10 psig /
0.34 to 0.69 bar
10 psig / 0.69 bar1J1469271425 to 10 psig /
0.34 to 0.69 bar
psig bar
10%Droop
20%Droop
10%Droop
20%Droop
10%Droop
20%Droop
10%Droop
20%Droop
10%Droop
20%Droop
SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
357
0.210.340.48
- - - -14
21.5
- - - -0.380.58
- - - -2231
- - - -0.590.83
6.5 1113
0.170.300.35
11.51822
0.310.480.59
- - - -- - - - 15.5
- - - -- - - - 0.42
- - - -- - - -24
- - - -- - - -0.64
- - - -- - - -
9
- - - -- - - -0.24
- - - -- - - -15
- - - -- - - -0.40
- - - -- - - -- - - -
- - - -- - - -- - - -
- - - -- - - -- - - -
- - - -- - - -- - - -
101520
0.691.01.4
284052
0.751.071.39
425772
1.131.531.93
1525.535
0.400.680.94
273952
0.721.041.39
243546
0.640.941.23
355167
0.941.371.80
141924
0.38 0.510.64
2231.541
0.590.841.10
- - - -2131
- - - -0.560.83
- - - -3551
- - - -0.941.37
30405060
2.12.83.44.1
7698118136
2.042.633.163.64
96119141165
2.573.193.784.42
496684
104
1.311.772.252.79
7397112132
1.962.603.003.54
6888
103122
1.822.362.763.27
95117138156
2.553.143.704.18
35445765
0.941.181.531.74
587389
106
1.551.962.382.84
44567491
1.181.501.982.44
7497117136
1.982.603.143.64
1. Outlet pressure setting was made at approximately 10% of the maximum capacity for the listed conditions.
INLET PRESSURE
OUTLET PRESSURE SETTING(1), SPRING PART NUMBER, AND OUTLET PRESSURE RANGE
4 inches w.c. / 10 mbar
1D8925270222 to
4 inches w.c. / 5 to
10 mbar
6 inches w.c. /15 mbar
1D8926270223.5 to
6 inches w.c. / 8.7 to
15 mbar
7 inches w.c. /17 mbar
1D8927270125 to
9 inches w.c. /12 to 22 mbar
14 inches w.c. /35 mbar
1D8932270328.5 to
18 inches w.c. / 21 to 45 mbar
14 inches w.c. /35 mbar
1D89332703214 to 28 inches w.c. /
35 to 70 mbar
1 psig / 0.07 bar1D893327032
14 to 28 inches w.c. / 35 to 70 mbar
2 psig / 0.14 bar1H975827032
0.75 to 2 psig /0.05 to 0.14 bar
psig bar
1 inch w.c. /3 mbarDroop
1 inch w.c. /3 mbarDroop
1 inch w.c. /3 mbarDroop
1 inch w.c. /3 mbarDroop
2 inch w.c /5 mbarDroop
1 inch w.c. /3 mbarDroop
2 inch w.c. /5 mbarDroop
10%Droop
20%Droop
10%Droop
20%Droop
SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
123
0.070.140.21
1420.826
0.380.560.70
1320
24.5
0.350.540.66
121721
0.320.460.56
58.212
0.130.220.32
8.415.219.5
0.220.410.52
- - - -- - - -- - - -
- - - -- - - -- - - -
- - - -- - - -- - - -
- - - -- - - -- - - -
- - - - 11.515.5
- - - - 0.310.42
- - - - 16
21.5
- - - - 0.430.58
- - - -- - - -12.5
- - - -- - - -0.34
- - - -- - - -18.5
- - - -- - - -0.50
51020
0.340.691.4
355278
0.941.392.09
335277
0.881.392.06
324879
0.861.292.12
163469
0.430.911.85
284576
0.75 1.212.04
142660
0.380.701.61
233869
0.621.021.85
2437.570
0.641.001.88
31.54477
0.841.182.06
20.53862
0.551.021.66
284676
0.751.232.04
30405060
2.12.83.44.1
101124146170
2.713.323.914.56
100122144168
2.683.273.864.50
100124145166
2.683.323.894.45
91109130155
2.442.923.484.15
97116136161
2.603.113.644.32
87107132152
2.332.873.544.07
93115137158
2.493.083.674.23
90110127149
2.412.953.403.99
101122145167
2.713.273.894.48
87105124145
2.332.813.323.89
101121145170
2.713.243.894.56
1. Outlet pressure setting was made at approximately 10% of the maximum capacity for the listed conditions.
Bulletin 71.1:133
9
Figure 6. Capacity Curves — Full-Capacity Constructions
1 psig /0.07 bar
2 psig / 0.14 bar
5 psig /0.34 bar
10 psig /0.69 bar
20 psig /1.4 bar
OU
TLET
PR
ESSU
RE,
inch
w.c
. / m
bar
21A0871–A
0 / 01 / 22 / 5
3 / 7
OU
TLET
PR
ESSU
RE,
inch
w.c
. / m
bar
21A0865–A
2 / 54 / 106 / 158 / 20
10 / 25
1 psig /0.07 bar
2 psig /0.14 bar
5 psig /0.34 bar
3 psig /0.21 bar
CAPACITY AND REGULATION 2 inch / DN 50 TYPE 133L SPRING 1D892727012SETPOINT: INLET PRESSURE: 2 psig / 0.14 bar OUTLET PRESSURE: 7 inch w.c. / 17 mbar FLOW: 3100 SCFH / 83.08 Nm3/h
OU
TLET
PR
ESSU
RE,
inch
w.c
. / m
bar
21A0866
CAPACITY AND REGULATION 2 inch / DN 50 TYPE 133L SPRING 1D892727012SETPOINT: INLET PRESSURE: 40 psig / 2.8 bar OUTLET PRESSURE: 7 inch w.c. / 17 mbar FLOW: 11,000 SCFH / 295 Nm3/h
10 psig /0.69 bar
20 psig /1.4 bar
30 psig /2.1 bar
40 psig /2.8 bar
50 psig /3.4 bar
60 psig /4.1 bar
OU
TLET
PR
ESSU
RE,
inch
w.c
. / m
bar
21A0867–AC0744/IL
6 / 158 / 20
10 / 2512 / 30
14 / 3416 / 4018 / 45
10 psig /0.69 bar
20 psig /1.4 bar
40 psig /2.8 bar
60 psig /4.1 bar
CAPACITY AND REGULATION 2 inch / DN 50 TYPE 133L SPRING 1D893227032SETPOINT: INLET PRESSURE: 40 psig / 2.8 bar OUTLET PRESSURE: 14 inch w.c. / 35 mbar FLOW: 11,000 SCFH / 295 Nm3/h
21A0870–A
2 / 0.14
3 / 0.214 / 0.285 / 0.356 / 0.41
20 psig /1.4 bar
30 psig /2.1 bar
40 psig /2.8 bar
50 psig /3.4 bar
60 psig /4.1 bar
CAPACITY AND REGULATION 2 inch / DN 50 TYPE 133H SPRING 10A9440X012SETPOINT: INLET PRESSURE: 40 psig / 2.8 bar OUTLET PRESSURE: 5 psig / 0.34 bar FLOW: 11,000 SCFH / 295 Nm3/h
21A0869–A1 / 0.07
2 / 0.14
3 / 0.21
20 psig /1.4 bar
40 psig /2.8 bar
60 psig /4.1 bar
CAPACITY AND REGULATION 2 inch / DN 50 TYPE 133L SPRING 1D893327032SETPOINT: INLET PRESSURE: 40 psig / 2.8 bar OUTLET PRESSURE: 1 psig / 0.07 bar FLOW: 11,000 SCFH / 295 Nm3/h
20 /0.5
0 /0
40 /1.1
60 /1.6
80 /2.1
100 /2.7
120 /3.2
140 /3.8
160 /4.3
180 / 4.8
21A0868–A
0.2 / 0.01
0.6 / 0.04
1.0 / 0.070.8 / 0.06
0.4 / 0.03 20 psig /1.4 bar
30 psig /2.1 bar
40 psig /2.8 bar
50 psig /3.4 bar
60 psig /4.1 bar
CAPACITY AND REGULATION 2 inch / DN 50 TYPE 133L SPRING 1D893327032SETPOINT: INLET PRESSURE: 40 psig / 2.8 bar OUTLET PRESSURE: 1 psig / 0.07 bar FLOW: 11,000 SCFH / 295 Nm3/h
0 /0
10 /0.3
20 /0.5
30 /0.8
40 /1.0
50 /1.3
60 /1.6
70 /1.9
80 /2.1
90 /2.4
0 /0
4 /0.1
8 /0.2
12 /0.3
16 /0.4
20 /0.5
24 /0.6
28 /0.8
32 /0.9
36 /1.0
2 / 54 / 106 / 158 / 20
10 / 25
OU
TLET
PR
ESSU
RE,
psig
/ ba
r
1.2 / 0.08
OU
TLET
PR
ESSU
RE,
psig
/ ba
rO
UTL
ET P
RES
SUR
E,ps
ig /
bar
20 /0.5
CAPACITY AND REGULATION2 inch / DN 50 TYPE 133ZSPRING COMPRESSION - 1D892527022 EXTENSION - 1K633427012SETPOINT: INLET PRESSURE: 1 psig / 0.07 bar OUTLET PRESSURE: 1 inch w.c. / 2 mbar FLOW: 3000 SCFH / 80.4 Nm3/h
0 /0
40 /1.1
60 /1.6
80 /2.1
100 /2.7
120 /3.2
140 /3.8
160 /4.3
180 / 4.8
20 /0.5
0 /0
40 /1.1
60 /1.6
80 /2.1
100 /2.7
120 /3.2
140 /3.8
160 /4.3
180 /4.8
20 /0.5
0 /0
40 /1.1
60 /1.6
80 /2.1
100 /2.7
120 /3.2
140 /3.8
160 /4.3
180 /4.8
20 /0.5
0 /0
40 /1.1
60 /1.6
80 /2.1
100 /2.7
120 /3.2
140 /3.8
160 /4.3
180 4.8
FLOW RATE IN THOUSANDS OF SCFH / Nm3/h0.6 SPECIFIC GRAVITY GAS AT 14.7 psia AND 60°F
FLOW RATE IN THOUSANDS OF SCFH / Nm3/h0.6 SPECIFIC GRAVITY GAS AT 14.7 psia AND 60°F
FLOW RATE IN THOUSANDS OF SCFH / Nm3/h0.6 SPECIFIC GRAVITY GAS AT 14.7 psia AND 60°F
FLOW RATE IN THOUSANDS OF SCFH / Nm3/h0.6 SPECIFIC GRAVITY GAS AT 14.7 psia AND 60°F
FLOW RATE IN THOUSANDS OF SCFH / Nm3/h0.6 SPECIFIC GRAVITY GAS AT 14.7 psia AND 60°F
FLOW RATE IN THOUSANDS OF SCFH / Nm3/h0.6 SPECIFIC GRAVITY GAS AT 14.7 psia AND 60°F
FLOW RATE IN THOUSANDS OF SCFH / Nm3/h0.6 SPECIFIC GRAVITY GAS AT 14.7 psia AND 60°F
Bulletin 71.1:133
10
Figure 7. Capacity Curves — Restricted Capacity Constructions
OU
TLET
PR
ESSU
RE,
psig
/ ba
r
23A1335–A
5.0 psig /0.34 bar
10 psig /0.69 bar
20 psig /1.4 bar
40 psig /2.8 bar
60 psig /4.1 bar
CAPACITY AND REGULATION 2 inch / DN 50 TYPE 133LSPRING 1H975827032 60% CAPACITY TRIMSETPOINT: INLET PRESSURE: 20 psig / 1.4 bar OUTLET PRESSURE: 2 psig / 0.14 bar FLOW: 4900 SCFH / 131 Nm3/h3.0 / 0.21
2.0 / 0.14
1.0 / 0.07
15 /0.4
0 /0
30 /0.8
45 /1.2
60 /1.6
75 /2.0
90 /2.4
105 /2.8
120 /3.2
135 /3.6
FLOW RATE IN THOUSANDS OF SCFH / Nm3/h0.6 SPECIFIC GRAVITY GAS AT 14.7 psia AND 60°F
23A1333–A
OU
TLET
PR
ESSU
RE,
psig
/ ba
r5.0 psig /0.34 bar
10 psig /0.69 bar
20 psig /1.4 bar
40 psig /2.8 bar
60 psig /4.1 bar
CAPACITY AND REGULATION 2 inch / DN 50 TYPE 133LSPRING 1H975827032 40% CAPACITY TRIMSETPOINT: INLET PRESSURE: 20 psig / 1.4 bar OUTLET PRESSURE: 2 psig / 0.14 bar FLOW: 2900 SCFH / 77.72 Nm3/h3.0 / 0.21
2.0 / 0.14
1.0 / 0.07
0 /0
10 /0.3
20 /0.5
30 /0.8
40 /1.0
50 /1.3
60 /1.6
70 /1.9
80 /2.1
90 /2.4
FLOW RATE IN THOUSANDS OF SCFH / Nm3/h0.6 SPECIFIC GRAVITY GAS AT 14.7 psia AND 60°F
CAPACITY AND REGULATION 2 inch / DN 50 TYPE 133LSPRING 1H975827032 25% CAPACITY TRIMSETPOINT: INLET PRESSURE: 20 psig / 1.4 bar OUTLET PRESSURE: 2 psig / 0.14 bar FLOW: 2140 SCFH / 57.35 Nm3/h
5.0 psig /0.34 bar
10 psig /0.69 bar
20 psig /1.4 bar
40 psig /2.8 bar
60 psig /4.1 bar
1.0 / 0.07
2.0 / 0.14
3.0 / 0.21
OU
TLET
PR
ESSU
RE,
psig
/ ba
r
23A1332–A
0 /0
5 /0.1
10 /0.3
15 /0.4
20 /0.5
25 /0.7
30 /0.8
35 /0.9
40 /1.1
45 /1.2
FLOW RATE IN THOUSANDS OF SCFH / Nm3/h0.6 SPECIFIC GRAVITY GAS AT 14.7 psia AND 60°F
C0745/IL
CAPACITY AND REGULATION 2 inch / DN 50 TYPE 133LSPRING 1D892727012 60% CAPACITY TRIMSETPOINT: INLET PRESSURE: 20 psig / 1.4 barOUTLET PRESSURE: 7 inches w.c. / 17 mbarFLOW: 4900 SCFH / 131 Nm3/h
10 psig /0.69 bar
20 psig /1.4 bar
40 psig /2.8 bar
60 psig /4.1 bar
15 /0.4
0 /0
30 /0.8
45 /1.2
60 /1.6
75 /2.0
90 /2.4
105 /2.8
120 /3.2
135 /3.6
OU
TLET
PR
ESSU
RE,
inch
w.c
. / m
bar
23A1337–A
12 / 30
8 / 20
4 / 10
FLOW RATE IN THOUSANDS OF SCFH / Nm3/h0.6 SPECIFIC GRAVITY GAS AT 14.7 psia AND 60°F
CAPACITY AND REGULATION 2 inch / DN 50 TYPE 133LSPRING 1D892727012 40% CAPACITY TRIMSETPOINT: INLET PRESSURE: 20 psig / 1.4 barOUTLET PRESSURE: 7 inches w.c. / 17 mbarFLOW: 2900 SCFH / 77.72 Nm3/h
10 psig /0.69 bar
20 psig /1.4 bar
40 psig /2.8 bar
60 psig /4.1 bar
OU
TLET
PR
ESSU
RE,
inch
w.c
. / m
bar
23A1334–A
12 / 30
8 / 20
4 / 10
0 /0
10 /0.3
20 /0.5
30 /0.8
40 /1.0
50 /1.3
60 /1.6
70 /1.9
80 /2.1
90 /2.4
FLOW RATE IN THOUSANDS OF SCFH / Nm3/h0.6 SPECIFIC GRAVITY GAS AT 14.7 psia AND 60°F
OU
TLET
PR
ESSU
RE,
inch
w.c
. / m
bar
23A1336–A
4 / 10
8 / 20
12 / 30
0 /0
CAPACITY AND REGULATION 2 inch / DN 50 TYPE 133LSPRING 1D892727012 25% CAPACITY TRIMSETPOINT: INLET PRESSURE: 20 psig / 1.4 bar OUTLET PRESSURE: 7 inches w.c. / 17 mbar FLOW: 2140 SCFH / 57.35 Nm3/h
10 psig /0.69 bar
20 psig /1.4 bar
40 psig /2.8 bar
60 psig /4.1 bar
5 /0.1
10 /0.3
15 /0.4
20 /0.5
25 /0.7
30 /0.8
35 /0.9
40 /1.1
45 /1.2
FLOW RATE IN THOUSANDS OF SCFH / Nm3/h0.6 SPECIFIC GRAVITY GAS AT 14.7 psia AND 60°F
Bulletin 71.1:133
11
Table 6. Restricted-Capacity Type 133H Regulated Flow in Thousands of SCFH of 0.6 Specific Gravity Gas at 14.7 psia and 60°F
INLETPRESSURE
OUTLET PRESSURE SETTING(1), SPRING PART NUMBER, AND OUTLET PRESSURE RANGE
25% Capacity 40% Capacity 60% Capacity
5 psig / 0.34 bar10A9440X0122 to 5 psig /
0.14 to 0.34 bar
10 psig / 0.69 bar1J1469271425 to 10 psig /
0.34 to 0.69 bar
5 psig / 0.34 bar10A9440X0122 to 5 psig /
0.14 to 0.34 bar
10 psig / 0.69 bar1J1469271425 to 10 psig /
0.34 to 0.69 bar
5 psig / 0.34 bar10A9440X0122 to 5 psig /
0.14 to 0.34 bar
10 psig / 0.69 bar1J1469271425 to 10 psig /
0.34 to 0.69 bar
psig bar10%
Droop20%
Droop10%
Droop20%
Droop10%
Droop20%
Droop10%
Droop20%
Droop10%
Droop20%
Droop10%
Droop20%
Droop
SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
71015204060
0.480.691.01.42.84.1
8.012.3- - - -20.833.545.5
0.210.33- - - -0.560.901.22
9.013.0- - - -21.233.5 45.5
0.240.35- - - -0.570.901.22
- - - -- - - -13.017.533.045.5
- - - -- - - -0.350.470.881.22
- - - -- - - -15.520.033.5 45.5
- - - -- - - -0.420.540.901.22
11.0 16.5- - - -31.552.072.7
0.300.44- - - -0.841.391.95
15.020.0 - - - -33.553.272.7
0.400.54- - - -0.901.431.95
- - - -- - - -16.523.5 46.0 67.0
- - - -- - - -0.440.631.231.80
- - - -- - - -23.5 30.553.2 72.7
- - - -- - - -0.630.821.431.95
13.020.0 - - - -36.070.0 105
0.350.54- - - -0.961.882.81
17.0 25.0- - - -46.577.5107
0.460.67- - - - 1.252.082.87
- - - -- - - -20.029.057.087.0
- - - -- - - -0.540.781.532.33
- - - -- - - -29.539.574.5107
- - - -- - - -0.791.062.002.87
1. Outlet pressure setting was made at approximately 10% of the maximum capacity for the listed conditions.
Table 7. Type 133HP Regulator 100% Capacities in Thousands of SCFH of 0.6 Specific Gravity Gas at 14.7 psia and 60°F
- continued -
OUTLET PRESSURE RANGE, CONTROL SPRING NUMBER,
AND COLOR
OUTLET PRESSURESETTING(1)
INLETPRESSURE
2-INCH / DN 50 BODY SIZE1.91-INCH / 48.5 mm ORIFICE SIZE
Droop from Setpoint
10% 20% 30%
psig bar psig bar SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
2 to 5 psig /0.14 to 0.34 bar
17B8632X012
Yellow
2 0.14
1020406080
100125150
0.691.42.84.15.56.98.6
10.3
10.416.427.037.147.257.169.582.0
0.280.440.720.991.261.531.862.20
18.929.849.167.585.7
103.9126.5149.1
0.510.801.321.812.302.783.394.00
27.543.371.297.9
124.3150.6183.4216.3
0.741.161.912.623.334.044.925.80
5 0.34
1020406080
100125150
0.691.42.84.15.56.98.6
10.3
20.235.159.682.4
104.9127.2155.0182.7
0.540.941.602.212.813.414.154.90
41.571.7
121.3167.9213.6258.9315.4371.8
1.111.923.254.505.726.948.459.96
42.872.3
121.5168.0213.6258.9315.4371.8
1.151.943.264.505.726.948.459.96
1. Outlet pressure setting was made at approximately 10% of the maximum capacity for the listed conditions. Grayareasindicatemaximumflowcapacity.
Bulletin 71.1:133
12
Table 7. Type 133HP Regulator 100% Capacities in Thousands of SCFH of 0.6 Specific Gravity Gas at 14.7 psia and 60°F
OUTLET PRESSURE RANGE, CONTROL SPRING NUMBER,
AND COLOR
OUTLET PRESSURESETTING(1)
INLETPRESSURE
2-INCH / DN 50 BODY SIZE1.91-INCH / 48.5 mm ORIFICE SIZE
Droop from Setpoint
10% 20% 30%
psig bar psig bar SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
4.5 to 10 psig /0.31 to 0.69 bar
17B8633X012
Orange
5 0.34
1020406080
100125150
0.691.42.84.15.56.98.6
10.3
11.419.633.045.758.170.585.8
101.2
0.310.520.881.221.561.892.302.71
21.436.461.384.7
107.7130.6159.0187.5
0.570.981.642.272.893.504.265.02
32.053.489.6
123.7157.3190.7232.2273.8
0.861.432.403.324.225.116.227.34
10 0.69
2530406080
100125150
1.72.12.84.15.56.98.6
10.3
40.347.159.984.0
107.4130.4159.0187.5
1.081.261.602.252.883.504.265.02
80.593.9119.1166.8213.0258.7315.4371.8
2.162.523.194.475.716.938.459.96
81.794.8119.7167.1213.2258.8315.4371.8
2.192.543.214.485.716.948.459.96
6 to 20 psig /0.41 to 1.4 bar
10C1238X012
Silver
10 0.69
1520406080
100125150
1.01.42.84.15.56.98.6
10.3
16.422.139.955.971.486.8
106.0125.0
0.440.591.071.501.912.332.843.35
32.042.275.4
105.0134.0163.0199.0235.0
0.861.132.022.813.594.375.336.30
51.967.7111.0155.0198.0240.0292.0344.0
1.391.812.984.155.316.437.839.22
20 1.4
2530406080
100125150
1.72.12.84.15.56.98.6
10.3
38.850.369.4
102.0133.0162.0198.0234.0
1.391.812.984.155.316.437.839.22
65.082.3112.0163.0211.0257.0315.0372.0
1.742.213.004.375.666.898.449.97
70.086.0114.0164.0211.0258.0315.0372.0
1.882.303.064.405.666.918.449.97
16 to 30 psig /1.1 to 2.1 bar
10C1240X012
Red
20 1.4
2530406080
100125150
1.72.12.84.15.56.98.6
10.3
24.831.843.563.883.0
101.0124.0146.0
0.660.851.171.712.222.713.233.91
50.462.684.0
122.0158.0192.0235.0277.0
1.351.682.253.274.235.156.307.42
70.086.0114.0164.0211.0258.0315.0372.0
1.882.303.064.405.666.918.449.97
30 2.1
35406080
100125150
2.42.84.15.56.98.6
10.3
43.053.888.0117.0145.0178.0211.0
1.151.442.363.143.894.775.66
80.698.4
156.0207.0255.0313.0371.0
2.162.644.185.556.838.399.94
88.2104.0159.0208.0256.0314.0371.0
2.362.794.265.576.868.429.94
1. Outlet pressure setting was made at approximately 10% of the maximum capacity for the listed conditions. Grayareasindicatemaximumflowcapacity.
- continued -
Bulletin 71.1:133
13
OUTLET PRESSURE RANGE, CONTROL SPRING NUMBER,
AND COLOR
OUTLETPRESSURESETTING(1)
INLETPRESSURE
2-INCH / DN 50 BODY SIZE1.91-INCH / 48.5 mm ORIFICE SIZE
Droop from Setpoint
10% 20% 30%
psig bar psig bar SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
26 to 40 psig /1.8 to 2.8 bar
10C1241X012
Blue
30 2.1
35406080
100125150
2.42.84.15.56.98.6
10.3
28.935.757.576.494.3116.0137.0
0.780.961.542.052.533.113.67
59.671.0110.0146.0179.0220.0260.0
1.601.902.953.914.805.906.97
88.2104.0 159.0208.0256.0314.0371.0
2.362.794.265.576.868.429.94
40 2.8
45506080
100125150
3.13.44.15.56.98.6
10.3
43.552.668.495.4
120.0149.0177.0
1.171.411.832.563.223.994.74
96.2114.0146.0186.0232.0287.0341.0
2.583.063.914.986.227.699.14
106.0122.0151.0204.0253.0312.0370.0
2.843.274.055.476.788.369.92
36 to 50 psig /2.5 to 3.4 bar
10C1242X012
Green
40 2.8
45506080
100125150
3.13.44.15.56.98.6
10.3
36.243.456.278.197.9
122.0145.0
0.971.161.512.092.623.273.89
76.188.1110.0150.0187.0232.0276.0
2.042.362.954.025.016.227.40
106.0122.0 151.0204.0253.0 312.0370.0
2.843.274.055.476.788.369.92
50 3.4
556080
100125150
3.84.15.56.98.6
10.3
50.459.590.2116.0147.0176.0
1.351.602.423.113.944.72
112.0130.0191.0227.0283.0338.0
3.003.485.126.087.589.06
124.0141.0197.0248.0309.0368.0
3.323.785.286.658.289.86
45 to 60 psig /3.1 to 4.1 bar
10C1243X012
White
50 3.4
556080
100125150
3.84.15.56.98.6
10.3
43.551.076.999.0
125.0149.0
1.171.372.062.653.353.99
92.7105.0151.0191.0239.0285.0
2.482.814.055.126.407.64
124.0141.0197.0248.0309.0368.0
3.323.785.286.658.289.86
60 4.1
657080
100125150
4.54.85.56.98.6
10.3
57.566.583.2112.0144.0174.0
1.541.782.233.003.864.66
127.0146.0179.0236.0280.0336.0
3.403.914.806.327.509.00
143.0159.0188.0242.0305.0365.0
3.834.265.046.498.179.78
1. Outlet pressure setting was made at approximately 10% of the maximum capacity for the listed conditions. Grayareasindicatemaximumflowcapacity.
Table 7. Type 133HP Regulator 100% Capacities in Thousands of SCFH of 0.6 Specific Gravity Gas at 14.7 psia and 60°F (continued)
Bulletin 71.1:133
14
Table 8. Type 133HP Regulator 25% Capacities in Thousands of SCFH of 0.6 Specific Gravity Gas at 14.7 psia and 60°F
OUTLET PRESSURERANGE, CONTROLSPRING NUMBER,
AND COLOR
OUTLET PRESSURESETTING(1)
INLETPRESSURE
2-INCH / DN 50 BODY SIZE1.91-INCH / 48.5 mm ORIFICE SIZE
Droop from Setpoint
10% 20% 30%
psig bar psig bar SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
2 to 5 psig /0.14 to 0.34 bar
17B8632X012
Yellow
2 0.14
1020406080
100125150
0.691.42.84.15.56.98.6
10.3
4.06.4
10.514.518.422.327.232.0
0.110.170.280.390.490.600.730.86
7.812.520.628.436.043.753.262.7
0.210.340.550.760.971.171.431.68
13.412.234.948.161.174.090.1
106.2
0.360.330.941.291.641.982.422.85
5 0.34
1020406080
100125150
0.691.42.84.15.56.98.6
10.3
8.314.925.435.244.854.366.278.1
0.220.400.680.941.201.461.772.09
11.520.334.647.961.074.090.1
106.2
0.310.540.931.281.641.982.422.85
11.920.534.748.061.074.090.1
106.2
0.320.550.931.291.641.982.422.85
4.5 to 10 psig /0.31 to 0.69 bar
17B8633X012
Orange
5 0.34
1020406080
100125150
0.691.42.84.15.56.98.6
10.3
4.47.8
13.318.423.428.434.640.8
0.120.210.360.490.630.760.931.09
8.715.426.136.246.155.968.180.2
0.230.410.700.971.241.501.832.15
11.920.534.748.061.074.090.1
106.2
0.320.550.931.291.641.982.422.85
10 0.69
2530406080
100125150
1.72.12.84.15.56.98.6
10.3
17.019.925.535.945.955.868.080.2
0.460.530.680.961.231.501.822.15
22.626.533.847.560.873.990.1
106.2
0.610.710.911.271.631.982.422.85
23.026.834.047.660.973.990.1
106.2
0.620.720.911.281.631.982.422.85
6 to 20 psig /0.41 to 1.4 bar
10C1238X012
Silver
10 0.69
1520406080
100125150
1.01.42.84.15.56.98.6
10.3
6.38.8
16.423.129.535.843.751.5
0.170.240.440.620.790.961.171.38
13.318.333.847.560.873.990.1
106.2
0.360.490.911.271.631.982.422.85
14.118.934.047.660.973.990.1
106.2
0.380.510.911.281.631.982.422.85
20 1.4
2530406080
100125150
1.72.12.84.15.56.98.6
10.3
15.721.630.745.959.873.389.8
106.1
0.420.580.821.231.601.962.412.84
16.822.331.146.160.073.489.8
106.1
0.450.600.831.241.611.972.412.84
18.623.531.946.560.273.589.9
106.2
0.500.630.861.251.611.972.412.85
1. Outlet pressure setting was made at approximately 10% of the maximum capacity for the listed conditions. Grayareasindicatemaximumflowcapacity.
- continued -
Bulletin 71.1:133
15
Table 8. Type 133HP Regulator 25% Capacities in Thousands of SCFH of 0.6 Specific Gravity Gas at 14.7 psia and 60°F (continued)
OUTLET PRESSURERANGE, CONTROLSPRING NUMBER,
AND COLOR
OUTLET PRESSURESETTING(1)
INLETPRESSURE
2-INCH / DN 50 BODY SIZE1.91-INCH / 48.5 mm ORIFICE SIZE
Droop from Setpoint
10% 20% 30%
psig bar psig bar SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
16 to 30 psig /1.1 to 2.1 bar
10C1240X012
Red
20 1.4
2530406080
100125150
1.72.12.84.15.56.98.6
10.3
9.212.617.826.634.642.351.961.3
0.250.340.480.710.931.131.391.64
16.822.331.146.160.073.489.8
106.1
0.450.600.831.241.611.972.412.84
18.623.531.946.560.273.589.9
106.2
0.500.630.861.251.611.972.412.85
30 2.1
35406080
100125150
2.42.84.15.56.98.6
10.3
18.521.537.150.062.176.690.9
0.500.580.991.341.662.052.44
20.226.143.658.472.389.2
105.7
0.540.701.171.561.942.392.83
23.028.144.659.072.789.4
105.9
0.620.751.201.581.952.402.84
26 to 40 psig /1.8 to 2.8 bar
10C1241X012
Blue
30 2.1
35406080
100125150
2.42.84.15.56.98.6
10.3
10.313.623.431.639.148.357.3
0.280.360.630.851.051.291.54
20.226.143.658.472.389.2
105.7
0.540.701.171.561.942.392.83
23.028.144.659.072.789.4
105.9
0.620.751.201.581.952.402.84
40 2.8
45506080
100125150
3.13.44.15.56.98.6
10.3
15.520.327.839.950.663.275.4
0.420.540.741.071.361.692.02
23.729.739.656.070.788.1
105.0
0.640.801.061.501.902.362.81
27.532.741.657.271.588.6
105.4
0.740.881.121.531.922.372.82
36 to 50 psig /2.5 to 3.4 bar
10C1242X012
Green
40 2.8
45506080
100125150
3.13.44.15.56.98.6
10.3
12.516.422.432.140.750.860.6
0.340.440.600.861.091.361.62
23.729.739.656.070.788.1
105.0
0.640.801.061.501.902.362.81
27.532.741.657.271.588.6
105.4
0.740.881.121.531.922.372.82
50 3.4
556080
100125150
3.84.15.56.98.6
10.3
17.522.537.148.761.974.5
0.470.600.991.301.662.00
27.033.352.568.486.6
103.9
0.720.891.411.832.322.78
31.937.254.669.887.5
104.5
0.861.001.461.872.342.80
45 to 60 psig /3.1 to 4.1 bar
10C1243X012
White
50 3.4
556080
100125150
3.84.15.56.98.6
10.3
14.818.931.140.952.062.5
0.400.510.831.101.391.68
27.033.352.568.486.6
103.9
0.720.891.411.832.322.78
31.937.254.669.887.5
104.5
0.861.001.461.872.342.80
60 4.1
657080
100125150
4.54.85.56.98.6
10.3
19.524.733.146.360.473.5
0.520.660.831.241.621.97
30.436.947.665.284.5
102.4
0.820.991.281.752.262.74
36.441.751.167.485.9
103.4
0.981.121.371.812.302.77
1. Outlet pressure setting was made at approximately 10% of the maximum capacity for the listed conditions. Grayareasindicatemaximumflowcapacity.
Bulletin 71.1:133
16
Figure 8. 133 Series Assembly Positions for Body/Spring Case Orientation
TYPES 133L, 133H, AND 133Z
VENT ORIENTATION
POSITION 1(STANDARD)
POSITION 2 POSITION 3 POSITION 4
INLET
E
OUTLET (STANDARD)
C
D
F
3/4-14 NPTCONTROLCONNECTION
VENT
GE29263
1/4-inch / 6.35 mm STREET ELBOW
POSITION 1(STANDARD)
POSITION 2 POSITION 3 POSITION 4
VENT ORIENTATION
INLET
(STANDARD)C
D
F
E
27B5342A–A/DOC
TYPE 133HP
Bulletin 71.1:133
17
Table 9. Type 133HP Regulator 40% Capacities in Thousands of SCFH of 0.6 Specific Gravity Gas at 14.7 psia and 60°F
OUTLET PRESSURERANGE, CONTROLSPRING NUMBER,
AND COLOR
OUTLET PRESSURESETTING(1)
INLETPRESSURE
2-INCH / DN 50 BODY SIZE1.91-INCH / 48.5 mm ORIFICE SIZE
Droop from Setpoint
10% 20% 30%
psig bar psig bar SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
2 to 5 psig /0.14 to 0.34 bar
17B8632X012
Yellow
2 0.14
1020406080
100125150
0.691.42.84.15.56.98.6
10.3
6.910.516.622.728.834.842.450.0
0.180.280.440.610.770.931.141.34
13.220.131.943.655.266.981.596.0
0.350.540.861.171.481.792.182.57
19.729.747.264.481.799.0
120.5142.1
0.530.801.261.732.192.653.233.81
5 0.34
1020406080
100125150
0.691.42.84.15.56.98.6
10.3
14.524.439.554.068.582.9
101.0119.1
0.390.651.061.451.842.222.713.19
19.832.852.972.391.6111.0135.2159.3
0.530.881.421.942.462.983.624.27
20.432.952.972.391.6111.0135.2159.3
0.550.881.421.942.462.983.624.27
4.5 to 10 psig /0.31 to 0.69 bar
17B8633X012
Orange
5 0.34
1020406080
100125150
0.691.42.84.15.56.98.6
10.3
3.85.89.2
12.515.919.323.527.7
0.100.160.250.340.430.520.630.74
7.110.717.023.329.535.743.551.3
0.190.290.460.620.790.961.171.38
10.415.724.934.043.152.263.675.0
0.280.420.670.911.161.401.702.01
10 0.69
2530406080
100125150
1.72.12.84.15.56.98.6
10.3
28.232.540.555.570.485.2
103.8122.4
0.760.871.081.491.892.282.783.28
37.042.652.9 72.391.6111.0135.2159.3
0.991.141.421.942.462.983.624.27
37.442.852.972.391.6111.0135.2159.3
1.001.151.421.942.462.983.624.27
6 to 20 psig /0.41 to 1.4 bar
10C1238X012
Silver
10 0.69
1520406080
100125150
1.031.42.84.15.56.98.6
10.3
11.315.126.336.045.655.267.379.3
0.300.400.700.961.221.481.802.12
23.630.952.972.391.6111.0135.2159.3
0.630.831.421.942.462.983.624.27
24.731.552.972.391.6111.0135.2159.3
0.660.841.421.942.462.983.624.27
20 1.4
2530406080
100125150
1.72.12.84.15.56.98.6
10.3
28.537.150.472.091.6111.0135.2159.3
0.760.991.351.932.462.983.624.27
31.238.851.272.291.6111.0135.2159.3
0.841.041.371.942.462.983.624.27
33.240.151.972.391.6111.0135.2159.3
0.891.081.391.942.462.983.624.27
16 to 30 psig /1.1 to 2.1 bar
10C1240X012
Red
20 1.4
2530406080
100125150
1.72.12.84.15.56.98.6
10.3
17.222.129.842.554.165.579.894.0
0.460.590.801.141.451.762.142.52
31.238.851.272.291.6111.0135.2159.3
0.841.041.371.942.462.983.624.27
33.240.151.972.391.6111.0135.2159.3
0.891.081.391.942.462.983.624.27
30 2.1
35406080
100125150
2.42.84.15.56.98.6
10.3
34.438.461.279.796.9118.0139.1
0.921.031.642.142.603.163.73
38.746.671.091.5111.0135.2159.3
1.041.251.902.452.983.624.27
41.848.871.691.6111.0135.2159.3
1.121.311.922.462.983.624.27
1. Outlet pressure setting was made at approximately 10% of the maximum capacity for the listed conditions. Grayareasindicatemaximumflowcapacity.
- continued -
Bulletin 71.1:133
18
Table 9. Type 133HP Regulator 40% Capacities in Thousands of SCFH of 0.6 Specific Gravity Gas at 14.7 psia and 60°F (continued)
OUTLET PRESSURERANGE, CONTROLSPRING NUMBER,
AND COLOR
OUTLET PRESSURESETTING(1)
INLETPRESSURE
2-INCH / DN 50 BODY SIZE1.91-INCH / 48.5 mm ORIFICE SIZE
Droop from Setpoint
10% 20% 30%psig bar psig bar SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
26 to 40 psig /1.8 to 2.8 bar
10C1241X012
Blue
30 2.1
35406080
100125150
2.42.84.15.56.98.6
10.3
19.724.639.050.761.675.088.4
0.530.661.041.361.652.012.37
38.746.671.091.5111.0135.2159.3
1.041.251.902.452.983.624.27
41.848.871.691.6111.0135.2159.3
1.121.311.922.462.983.624.27
40 2.8
45506080
100125150
3.13.44.15.56.98.6
10.3
30.337.148.065.680.998.9116.6
0.810.991.291.762.172.653.12
46.2 54.367.890.5110.9135.2 159.3
1.241.461.822.422.973.624.27
50.457.469.791.2111.0135.2159.3
1.351.541.872.442.983.624.27
36 to 50 psig /2.5 to 3.4 bar
10C1242X012
Green
40 2.8
45506080
100125150
3.13.44.15.56.98.6
10.3
24.630.038.852.965.379.894.0
0.660.801.041.421.752.142.52
46.2 54.367.890.5110.9135.2 159.3
1.241.461.822.422.973.624.27
50.457.469.791.2111.0135.2159.3
1.351.541.872.442.983.624.27
50 3.4
556080
100125150
3.84.15.56.98.6
10.3
34.841.862.979.798.7116.6
0.931.121.692.142.643.12
53.761.988.1110.0135.2159.3
1.441.662.362.953.624.27
59.066.089.8110.7135.2159.3
1.581.772.412.973.624.27
45 to 60 psig /3.1 to 4.1 bar
10C1243X012
White
50 3.4
556080
100125150
3.84.15.56.98.6
10.3
29.535.353.067.283.198.1
0.790.951.421.802.232.63
53.761.988.1110.0135.2159.3
1.441.662.362.953.624.27
59.066.089.8110.7135.2159.3
1.581.772.412.973.624.27
60 4.1
657080
100125150
4.54.85.56.98.6
10.3
39.546.758.677.898.1116.8
1.061.251.572.082.633.13
61.369.583.8
108.0134.6159.3
1.641.862.252.893.614.27
67.674.687.2
109.6135.1159.3
1.812.002.342.943.624.27
1. Outlet pressure setting was made at approximately 10% of the maximum capacity for the listed conditions. Grayareasindicatemaximumflowcapacity.
Bulletin 71.1:133
19
Table 10. Type 133HP Regulator 60% Capacities in Thousands of SCFH of 0.6 Specific Gravity Gas at 14.7 psia and 60°F
OUTLET PRESSURERANGE, CONTROLSPRING NUMBER,
AND COLOR
OUTLET PRESSURESETTING(1)
INLETPRESSURE
2-INCH / DN 50 BODY SIZE1.91-INCH / 48.5 mm ORIFICE SIZE
Droop from Setpoint
10% 20% 30%
psig bar psig bar SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
2 to 5 psig /0.14 to 0.34 bar
17B8632X012
Yellow
2 0.14
1020406080
100125150
0.691.42.84.15.56.98.6
10.3
9.1 14.524.233.542.651.863.274.5
0.240.390.650.901.141.391.692.00
17.728.347.165.283.0
100.8122.9145.0
0.470.761.26 1.752.222.703.293.89
26.442.170.096.9
123.4149.8182.7215.6
0.711.131.882.603.314.024.905.78
5 0.34
1020406080
100125150
0.691.42.84.15.56.98.6
10.3
18.833.657.8 80.5
102.9125.1152.7180.2
0.500.901.552.162.763.354.094.83
26.145.778.4
109.1139.4169.4206.7244.0
0.701.222.102.923.744.545.546.54
27.046.178.5
109.2139.4169.4206.8244.0
0.721.242.102.933.744.545.546.54
4.5 to 10 psig /0.31 to 0.69 bar
17B8633X012
Orange
5 0.34
1020406080
100125150
0.691.42.84.15.56.98.6
10.3
10.017.730.442.354.065.780.194.6
0.270.470.821.131.451.762.152.54
20.034.859.582.9
105.8128.6157.0185.2
0.540.931.602.222.843.454.214.96
27.046.178.5
109.2139.4169.4206.8244.0
0.721.242.102.933.744.545.546.54
10 0.69
2530406080
100125150
1.72.12.84.15.56.98.6
10.3
38.345.157.881.8
105.1128.0156.5184.9
1.031.211.552.192.823.434.194.96
51.260.076.6
108.0138.6168.8206.3243.7
1.401.632.072.903.724.535.536.53
52.160.777.1
108.3138.8168.9206.4243.8
1.401.632.072.903.724.535.536.53
6 to 20 psig /0.41 to 1.4 bar
10C1238X012
Silver
10 0.69
1520406080
100125150
1.01.42.84.15.56.98.6
10.3
14.620.037.352.767.782.5
100.8119.1
0.390.541.001.411.812.212.703.19
31.141.876.6
108.0138.6168.8206.3243.7
0.831.122.052.893.714.525.536.53
32.742.977.1
108.3138.8168.9206.4243.8
0.881.152.072.903.724.535.536.53
20 1.4
2530406080
100125150
1.72.12.84.15.56.98.6
10.3
36.949.269.2
103.6135.5166.5204.6242.3
0.991.321.862.783.634.465.486.49
40.952.071.1
104.7136.3167.0205.0 242.7
1.101.391.902.813.654.485.496.50
44.254.572.7
105.7136.9167.6205.4243.0
1.181.461.952.833.674.495.506.51
16 to 30 psig /1.1 to 2.1 bar
10C1240X012
Red
20 1.4
2530406080
100125150
1.72.12.84.15.56.98.6
10.3
22.028.940.560.478.996.9119.0141.0
0.590.781.081.622.122.603.193.78
40.952.071.1
104.7136.3167.0205.0242.7
1.101.391.902.813.654.485.496.50
44.254.572.7
105.7136.9 167.6205.4243.0
1.181.461.952.833.674.495.506.51
30 2.1
35406080
100125150
2.42.84.15.56.98.6
10.3
39.150.184.3113.6141.2174.8207.9
1.051.342.263.043.784.685.57
50.762.199.7
132.8164.5203.1241.2
1.36 1.662.673.564.415.446.46
55.766.0
101.8134.3165.6203.9241.8
1.491.772.733.604.445.466.48
1. Outlet pressure setting was made at approximately 10% of the maximum capacity for the listed conditions. Grayareasindicatemaximumflowcapacity.
- continued -
Bulletin 71.1:133
20
Table 10. Type 133HP Regulator 60% Capacities in Thousands of SCFH of 0.6 Specific Gravity Gas at 14.7 psia and 60°F (continued)
OUTLET PRESSURERANGE, CONTROLSPRING NUMBER,
AND COLOR
OUTLET PRESSURESETTING(1)
INLETPRESSURE
2-INCH / DN 50 BODY SIZE1.91-INCH / 48.5 mm ORIFICE SIZE
Droop from Setpoint
10% 20% 30%
psig bar psig bar SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
26 to 40 psig /1.8 to 2.8 bar
10C1241X012
Blue
30 2.1
35406080
100125150
2.42.84.15.56.98.6
10.3
25.031.9 53.471.989.3110.5131.4
0.670.861.431.932.392.963.52
50.762.199.7
132.8164.5203.1241.2
1.361.662.673.564.415.446.46
55.766.0
101.8134.3165.6203.9241.8
1.491.772.733.604.445.466.48
40 2.8
45506080
100125150
3.13.44.15.56.98.6
10.3
38.548.063.990.8115.0144.0172.1
1.031.291.712.433.083.864.61
60.572.192.5
128.1161.0200.5239.1
1.621.932.483.434.325.376.41
67.177.596.4
130.7162.9201.9240.2
1,802,082,583,504,375,416,44
36 to 50 psig /2.5 to 3.4 bar
10C1242X012
Green
40 2.8
45506080
100125150
3.13.44.15.56.98.6
10.3
31.238.851.573.192.6115.8138.5
0.841.041.381.962.483.103.71
60.572.192.5
128.1161.0200.5239.1
1.621.932.483.434.325.376.41
67.177.596.4
130.7162.9201.9240.2
1.802.082.583.504.375.416.44
50 3.4
556080
100125150
3.84.15.56.98.6
10.3
44.253.984.8110.9140.9169.7
1.181.442.272.973.784.55
70.382.1
121.7156.4197.1236.5
1.882.203.264.195.286.34
78.689.0
125.9159.4199.3238.2
2.112.383.374.275.346.38
45 to 60 psig /3.1 to 4.1 bar
10C1243X012
White
50 3.4
556080
100125150
3.84.15.56.98.6
10.3
37.345.471.493.2118.4142.6
1.001.221.912.503.173.82
70.382.1
121.7156.4197.1236.5
1.882.203.264.195.286.34
78.689.0
125.9159.4199.3238.2
2.112.383.374.275.346.38
60 4.1
657080
100125150
4.54.85.56.98.6
10.3
50.059.977.0
105.8137.5167.4
1.341.602.062.843.684.49
80.192.0113.2150.5192.9233.2
2.152.473.034.035.176.25
90.1100.5119.8155.0196.2235.8
2.422.693.214.155.266.32
1. Outlet pressure setting was made at approximately 10% of the maximum capacity for the listed conditions. Grayareasindicatemaximumflowcapacity.
Bulletin 71.1:133
21
Figure 9. Dimensions
TYPES 133H, 133L, AND 133Z REGULATOR
13.38 / 340
5.00 / 127
10.00 / 254
14.12 / 359
1-8 NPTSCREENED VENT
3/4-14 NPTCONTROL CONNECTION
7.94 / 202
4.38 / 111
2-inch / DN 50, CL125 FF2-inch / DN 50, CL150 RF
2-11 1/2 NPT
10.00 / 254
5.00 / 127
2.12 / 53.8
Inch / mm
10A8094E
Bulletin 71.1:133
22
Figure 9. Dimensions (continued)
Inch / mm
TYPE 133HP REGULATOR
14.88 / 378
4.56 / 116
A6982/IL
TYPE Y602-7VENT
1/4-18 NPTDOWNSTREAM CONTROL LINE
6.94 / 176
Ø 9.88 / 251
5.00 / 127
10.00 / 254
2-inch / DN 50, CL125 FF2-inch / DN 50, CL150 RF
Bulletin 71.1:133
23
Ordering InformationUsetheSpecificationssectiononpage2andcarefullyreviewthedescriptiontotherightofeachspecification.Use this information to complete the Ordering Guide
Type 133HP 2 to 5 psig / 0.14 to 0.34 bar, Yellow 4.5 to 10 psig / 0.31 to 0.69 bar, Orange 6 to 20 psig / 0.41 to 1.4 bar, Silver 16 to 30 psig / 1.1 to 2.1 bar, Red 26 to 40 psig / 1.8 to 2.8 bar, Blue 36 to 50 psig / 2.5 to 3.4 bar, Green 45 to 60 psig / 3.1 to 4.1 bar, White
Trim, Percent of Full Capacity (Select One) 100 percent (standard) 60 percent 40 percent 25 percent
Elastomers (Select One) Nitrile (NBR) (standard) Fluorocarbon (FKM) (Available for Types 133L and 133H only)
Body Position (refer to Figure 8) (Select One) Position 1 (standard) Position 2 Position 3 Position 4
Vent Position (refer to Figure 8) (Select One) Position C (standard for Type 133HP) Position D Position E (standard for Types 133L, 133H, and 133Z) Position F
Ordering GuideType (Select One) 133L 133H 133Z 133HP
Body Material and End Connection Style (Select One) Cast Iron NPT CL125 FF Steel NPT CL150 RF
Outlet Pressure Range (Select One) Type 133L or 133H 2 to 4 inches w.c. / 5 to 10 mbar, Brown 3.5 to 6 inches w.c. / 9 to 15 mbar, Red 5 to 9 inches w.c. / 12 to 22 mbar, Black 8.5 to 18 inches w.c. / 21 to 45 mbar, White 14 to 28 inches w.c. / 35 to 70 mbar, Green 0.75 to 2 psig / 52 mbar to 0.14 bar, Blue Type 133H 1.5 to 3 psig / 0.10 to 0.21 bar, Orange 2 to 5 psig / 0.14 to 0.34 bar, Yellow 5 to 10 psig / 0.34 to 0.69 bar, Blue Type 133Z -1 to 1 inch w.c. / -2 to 2 mbar, Unpainted 0 to 4 inch w.c. / 0 to 10 mbar, Brown
on the following page. Specify the desired selection wherever there is a choice to be made. Then send the OrderingGuidetoyourlocalSalesOffice.
Bulletin 71.1:133
Regulators Quick Order Guide
* * * Readily Available for Shipment
* * Allow Additional Time for Shipment
* Special Order, Constructed from Non-Stocked Parts. ConsultyourlocalSalesOfficeforAvailability.
Availability of the product being ordered is determined by the component with the longest shipping time for the requested construction.
Specification WorksheetApplication:SpecificUse__________________________________LineSize____________________________________FluidType___________________________________SpecificGravity_______________________________Temperature_________________________________Does the Application Require Overpressure Protection? Yes NoPressure:Maximum Inlet Pressure (P1max)__________________Minimum Inlet Pressure (P1min)___________________Downstream Pressure Setting(s) (P2)______________SetPressure_________________________________Maximum Flow (Qmax)__________________________Accuracy Requirements:Less Than or Equal To: 5% 10% 20% 40%Construction Material Requirements (if known):________________________________________________________________________________________
©Emerson Process Management Regulator Technologies, Inc., 1972, 2013; All Rights Reserved
The Emerson logo is a trademark and service mark of Emerson Electric Co. All other marks are the property of their prospective owners. Fisher is a mark owned by Fisher Controls International LLC, a business of Emerson Process Management.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. We reserve the right to modify or improve the designs or specifications of such products at any time without notice.
Emerson Process Management Regulator Technologies, Inc. does not assume responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and maintenance of any Emerson Process Management Regulator Technologies, Inc. product remains solely with the purchaser.
Industrial Regulators
Emerson Process Management Regulator Technologies, Inc.
USA - HeadquartersMcKinney, Texas 75069-1872, USATel: +1 800 558 5853Outside U.S. +1 972 548 3574
Asia-PacificShanghai 201206, ChinaTel: +86 21 2892 9000
EuropeBologna 40013, ItalyTel: +39 051 419 0611
Middle East and AfricaDubai, United Arab EmiratesTel: +971 4811 8100
Natural Gas Technologies
Emerson Process ManagementRegulator Technologies, Inc.
USA - HeadquartersMcKinney, Texas 75069-1872, USATel: +1 800 558 5853Outside U.S. +1 972 548 3574
Asia-PacificSingapore 128461, SingaporeTel: +65 6770 8337
EuropeBologna 40013, ItalyTel: +39 051 419 0611Chartres 28008, FranceTel: +33 2 37 33 47 00
TESCOM
Emerson Process ManagementTescom Corporation
USA - HeadquartersElk River, Minnesota 55330-2445, USATels: +1 763 241 3238 +1 800 447 1250
EuropeSelmsdorf 23923, GermanyTel: +49 38823 31 287
Asia-PacificShanghai 201206, ChinaTel: +86 21 2892 9499
For further information visit www.emersonprocess.com/regulators