Upload
papercraft-vn
View
217
Download
0
Embed Size (px)
Citation preview
7/31/2019 1280927357811
http://slidepdf.com/reader/full/1280927357811 1/4
The Paper Puzzle Parade
The KitHow to
build
Send in
your record
Tips and
tricks
Back to the
parade
Hi there!
Still looking for something to
shoot into the sky on new year
eve? Here it is:
Build your own little paper rocket
- it comes complete with a
pneumatic launch pad.
Using pressurized air as it's only
fuel, the rocket might rise as high
as five meters. No fire and no
explosives are used - it's perfectlysafe for indoor use.
All you need is a printout of the rocket kit sheet -
a sheet of paper containing all paper parts forboth the rocket and the launching platform.
Simply download the
d your own paper rocket! http://www.groeg.de/puzzles/rocket.html
n 9 22.03.2010 10:25
7/31/2019 1280927357811
http://slidepdf.com/reader/full/1280927357811 2/4
rocket.pdf (70kB)
PDF file. The Tips and Tools page gives some
hints on how to get a proper printout of this file
and also show up all the requiered tools.
A color printout will make a cute rocket, butrockets made from black and white prints will
just fly as high ...
Many copy-shops can make both b/w and color prints from the files above.
Print the file onto a light cardboard (approx. 160 g m-2)
; most color
printers and copy machines can handle this.
Please take care: The original file fits onto a "DIN A4" sheet. If you have
to use the american "letter" sheets, you might have to resize the printout.
Building the rocket is rated "tricky". Folding the bellow requieres some
endurance. The most important thing to observe is that all bellow parts must be
air tight! The more precise you work, the higher the rocket will fly.
The most difficult part is the bellow's
side wall. Cut it out and carefully
scribe the bending lines! Then strictly
follow the bending lines:
Outside bend line
Inside bend line
as described in detail on the Tools
and Tips page. The bends must notbreak! If they do, close the slits with
adhesive tape, applied to the back side of the paper.
The folded bellow is then glued to the base plate. Remember: The connection
ought to be air tight!
Fold up the flaps at the front of the base plate and glue them to the top side of the
folded bellow.
Build the starting tube by coiling the part
around a pen or a stick. Slide it up throughthe top plate as shown on the left and glue it
on the back (bottom) side of the top plate.
d your own paper rocket! http://www.groeg.de/puzzles/rocket.html
n 9 22.03.2010 10:25
7/31/2019 1280927357811
http://slidepdf.com/reader/full/1280927357811 3/4
After
the
glue
of the first connections has dried, mount
the top plate on top of the bellow.
Check whether everything is air tight:Close the end of the starting tube with
your finger and carefully press the bellow.
If you find any escapes for the air, stop
them up!
Now build the rocket itself. Once again, the tubular part
should be prepared by winding the paper around a stick or
a pen. The finished tube must fit over the starting tube and
slide easily along it.
Form a cone as the rocket tip and glue it on top of the tube- once again: Air tight, please ...
Build the fins and glue them to the sides of the rocket.
Wait some minutes to allow the glue to dry.
Put the launch pad onto a robust
and unbreakable surface!
Remove all sharp or pointed object
around the pad!
Keep the airspace above the pad
free from all faces!
Now you're ready for the first take off:
Slide the rocket over the starting tube.
Carefully bash onto the top of the bellow with your flat hand.
Watch the rocket race into the sky - or most likely into your room's ceiling ... If
you did a good work with the bellow, five meters of height should be no problem.
If you have built the rocket - why not leave a comment in my guestbook?
New: Send in your flight data!
d your own paper rocket! http://www.groeg.de/puzzles/rocket.html
n 9 22.03.2010 10:25
7/31/2019 1280927357811
http://slidepdf.com/reader/full/1280927357811 4/4
Glue to top sideof base plate
Base Plate(top side)
Glue bellow side wall here
G l u e b e l l o w s i d e w a l l h e r e
Glue to bottom sideof bellow top plate
Bellow side wall
Rocket tube Rocket tip
Build your own paper rocket
Fins
© 1 9 9 8 b y G r ö g
Bellow top plate
S t a r t i n g t u b e
10
© 1998 by Grög
1
3
4 5
6
7
8
9
2
Z E
R O !
C a u t i o n !
K e e p a i r s p a c e
a b o v e l a u n c h p a d
c l e a r o f f a c e s !
M o r e i n f o r m a t i o n , b u i l d i n g i n s t r u c t i o n s
a n d m o r e p a p e r p u z z l e s h a v e a l o o k a t :
h t t p : / / w w w
. g r o e g . d e / p u z z l e s
( c ) 1 9 9 8 - 2 0 0
2 b y G e o r g E g g e r s - g r o e g @ g r o e g . d e
D A N
G E R ! D
o n o t h o l d y o u r f a c e
a b o v e t h e l a u n c h i n g p l a t f o r m
I n s i d e b e n d
O u t s i d e b e n d