1279370006886

7/31/2019 1279370006886

1/9

Agreeable Sheep Instructions 1 Rob Ives / Flying Pig 2007

You will need a craft knife or other sharp knife, a pair of scissors, some glue

and a glue spreader.

The best type of glue to use is white school glue (PVA.)

Print out the parts sheets onto thin cardboard. Photocopier card is ideal.

Notice that the parts pages are marked front and back. Print out a front page,

flip it over, then print the back onto the same sheet. Leave the ink to dry

completely before continuing.

Before cutting anything out, score along all the dotted

lines and cut out any holes with a craft knife. Both these

jobs are easier to do on full sheets of card.

Dashed lines are hill folds, dotted lines are valley folds.

Cut along the solid lines. Grey areas show where to

glue.

Cut

out

Dashed lines are

hill folds

Dotted lines are

valley folds

Black lines show

where to cut.

Shaded areas show

where to glue.

InstructionsInstructions

1

2

Youll need a coin

about this size.

Fold round and glue the

body inner together. (1)

Glue the body inner into

the body. Use the two very

small dots on the outside

of the body to line up the

diagonal corners of the

body inner. (3) You might

need to hold the body up

to the light to see through

it.

Roll the body round and

glue it to the other side

of the body inner. (3)

Use thes small dots

for alignment.

7/31/2019 1279370006886

2/9


3 4

5

7

6

Assemble the head. (4)

Glue the neck to the head.

(5)

Glue the neck to the body

inner. (6)

Head

Neck

Body Inner

Glue the Cam Follower into

place in the box (18 - see

box. 7)


Push-rod. (19)

Thread the Push-rod up

through the hole in the top of

the box and glue it first to the

inside of the Head (20) then to

the Cam Follower. (21 - see

the picture in box 7 for thecorrect orientation of these

parts.)

Push-rod

Cam Shaft

Cam

Fold the two flaps at the

bottom of the Box round andglue them into place. (7)

Glue the two halves of the

Box together. (8)

Glue on the Box Top. (9-10)

Fold the bottom flaps over

and glue them into place.

(11)

Fold the side supports

round and glue them

down. (12)

Glue the sheep to the Box

top. (13-14)

Find a coin of approximately 20mm diameter. A penny in

the UK or a cent in Europe and the USA will be ideal.

Wrap the Coin Holder round the coin and glue it down. (15)

Glue the coin into the centre of

the Cam Follower. (16)


Cam Follower. (17)

Push-rod

Cam Follower


Cam Shaft. (22)

Glue on the Cam (23)

Thread the Cam Shaft into

the box making sure thatthe green end goes to the

hole with the green ring.

Glue the two washers

onto the cam shaft. (24)

7/31/2019 1279370006886

3/9


8

Fold the two

square sections

into each other

and glue. (27)

Fold the long flap

round and glue into

place. (28)

Glue the handle into

place. (29)

Not one to stand out of the crowd, our woolly friendagrees with everything you say..."Is this a good colour scheme?" "Yes!""Would you like to go for a walk?" "Yes!""Are you having a good time?" "Yes!""Does my bum look big in this?" ...probably bestnot to ask.With this agreeable model you need never get asecond opinion again.Baa baa baa!

Rob Ives / Flying Pig 2007Flying PigBroughton MoorMaryportCumbriaCA15 7RU UKt. 01900 814333f. 01900 557313www.flying-pig.co.uk

Assemble the handle inthree steps.

Glue the two square

sections as shown.

(25-26) Finish off the model by gluing

the Box Back into place on the

back of the model. (30)

7/31/2019 1279370006886

4/9

The Agreeable Sheep : Parts 1 Rob Ives / Flying Pig 2007

Agreeable SheepAgreeable Sheep

www.flying-pig.co.uk

10

8

12 12

12

12

Cut

outCut

out

Cut

out

Cut

out

Cut

out

11 11

7

11

11

7

9.

8

10

10

13

13

14

14

15

16

18

Box

Box

Coin Holder

Box Top

30

30

7/31/2019 1279370006886

5/9

15

10

8

7

12

12

1111

10

8

7

12

12

11

11

109

.

Agreeable Sheep : Parts 1 Back

7/31/2019 1279370006886

6/9


TopfrontTop front

4

44

4

17

14

13

14

13

2 6.3

1

Cam Follower

Hea

d

Body

BodyInner

7/31/2019 1279370006886

7/9

4

44

4

5

17

2

11

6

1

8

32

1


7/31/2019 1279370006886

8/9


Box

Back

Cam Shaft

Neck

Push-rod

26 25

27

27

28

24

23

23

24

24

24

29

29

5

6.

19

21

23

23

24

24

24

24

22

Not one to stand out of the crowd, our woolly

friend agrees with everything you say...

"Is this a good colour scheme?" "Yes!"

"Would you like to go for a walk?" "Yes!"

"Are you having a good time?" "Yes!"

"Does my bum look big in this?" ...probably best

not to ask.

With this agreeable model you need never get a

second opinion again.

Baa baa baa!

Rob Ives / Flying Pig 2007

Handle

Washer

Cam

www.flying-pig.co.uk

7/31/2019 1279370006886

9/9

19

22

20

29

29

25 26

28

27

27

20

30 3

0


Documents

1279370006886