Upload
daniel-avecilla
View
77
Download
5
Embed Size (px)
DESCRIPTION
tv
Citation preview
ELEKTRONIK A.S.TECHNICAL CHANGE BULLETIN CHANGE NO: 112
REF NO : DATE :12.03.2002
AFFECTED MODELS: MODELS WITH 11AK36 CHASSIS
START DATE : 14.03.2002
REASONS OF CHANGE:
FOR SMPS IC POSITION IC 841 OF CHASSIS 11AK36 , IC FROM DIFFERENT SUPPLIER ARE USED .TO SET THE SAME WORKING FREQUENCY OF APPROX. 50 KHZ FOR ALL SUPPLIER’S , SOME VALUES OF SOME COMPONENTS ARE DIFFERENT .THE TABLE BELOW SHOWS ALL USED IC’S WITH PRINT OF THEM AND THE VALUE OF THE OPTIONAL COMPONENTS .
COMPANY R804 C807 PRINT ON ICVESTEL CODE
COMPONENT NAME VESTEL CODE
COMPONENT NAME
HI-SINCERITY
30000531 RES CF 1/4W 15K J 30000088 CAP MKT 2.2NF 63V J H 3842 P
ON-SEMI 30000531 RES CF 1/4W 15K J 30000088 CAP MKT 2.2NF 63V J UC 3842AN
KEC N.C. 30000096 CAP MKT 27nF 100V J KIA 3842P
ST 30000770 RES CF 1/4W 680R 30000099 CAP MKT 33nF 100V J ST UC3842A
UTC 30000770 RES CF 1/4W 680R 30000099 CAP MKT 33nF 100V J UTC UC3842A
HUA-JING 30000770 RES CF 1/4W 680R 30000099 CAP MKT 33nF 100V J YD 3842
NOPCB
CODEVESTEL CODE COMPONENT NAME POSITION NUMBER QUANTITY
123
INNO PCB
CODEVESTEL CODE COMPONENT NAME POSITION NUMBER QUANTITY
123
CUSTOMER SUPPORT
ENGINEERQUALITY
MANAGER
ELEKTRONIK A.S. TECHNICAL CHANGE BULLETIN
CHANGE NO: 120 REF NO : DATE :11.12.2001
AFFECTED MODELS: ALL MODELS 11AK36
START DATE : 11.12.2001 REASONS OF CHANGE: TO INCREASE FLUCTUATION RELIABILITY
OUT NO PCB
CODE VESTEL CODE COMPONENT NAME POSITION NUMBER QUANTITY
1 AK36 30016654 CAP SMD 100NF 16V K R (0603 C810 1
2 30000345 CAP EL 10UF 50V M C811 1
3 30000531 RES CF 1/4W 15K J R804 1
4 30001158 RES MO 1/2W 0.33R J R810 1
5 30000088 CAP MKT 2.2NF 63V J C807 1
6 30000673 RES CF 1W 330K J R807 1
IN
NO PCB CODE
VESTEL CODE COMPONENT NAME POSITION NUMBER QUANTITY
1 AK36 30016126 CAP SMD 220NF 16V K R (0603) C810 1
2 30000387 CAP EL 33 UF 50 V M C811 1
3 30000770 RES CF 1/4 W 680R J R804 1
4 30000096 CAP MKT 27NF 100V J C807 1
5 30001173 RES MO 1W 0.47R J R810 1
6 30006754 RES MO 2W 120K J R807 1
CUSTOMER SUPPORT
ENGINEER QUALITY
MANAGER
CENGIZ TARHAN
ALI TUNC CAN
Form Rev.No:00 Form No: 10.KALT.68
Katod of D703
Smd 1k (note 1 )
Diode BA159(note 2 )
Cable between Katod of BA159 and Katod of D703 ( note 3 )
Service BulletinModel:
All models with AK36 Chassis.
ServiceBulletin No: 121
Priority( )S. All products.( )A. Items in Customer / Dealer stock / Service return goods.( )B. Customer stock / Units returned for Service.( X)C. Sold items returned for Service.( )D. Only Units returned to this bulletin.( )E. Others
SUBJECT : Improvemet on Hor. Tr –SMPS IC for AK36 Chs. DATE : Aug 16, 2002
<Objective>Please modify if following symptom occurs
<Symptom>While TV is switching to st-by off, the st-by led is blinking in a short time.
<Cause>The negative peaks between the anode and cathode of the Thyristor.
<Countermeasures>
Apply that modification:
CHANGE Q601 THEN,
Replace;
R804: RES CF 1/4W 15K J è RES CF 1/4W 1K J
R805: RES CF 1/4W 1K J è RES CF 1/4W 470R J
C807: CAP MKP 2.2 NF 63V J è CAP MKP 22 NF 100V J
Connect a RES SMD 1/16W 22K J between the base and collector of q601.
<Spare Parts order>
VE- 30000466: RES CF 1/4W 1K J
VE-30000712: RES CF 1/4W 470R J
VE-30000090: CAP MKP 22 NF 100V J
VE-30012669 : RES SMD 1/16W 22K J
<Start Date of Modification on Production.>
Service BulletinModel:
All models with AK36 Chassis.
ServiceBulletin No: 123
Priority( )S. All products.( )A. Items in Customer / Dealer stock / Service return goods.( )B. Customer stock / Units returned for Service.( X)C. Sold items returned for Service.( )D. Only Units returned to this bulletin.( )E. Others
SUBJECT : IC404 DEFECT DATE : MAY 30, 2002
<Objective>Please modify if following symptom occurs
<Symptom>While TV is switching to ON, there is no audio.
<Cause>The over voltage stress on the IC404.
<Countermeasures>
Apply that modification:
CHANGE IC401 THEN,
Replace;
J188: JUMBER WIRE è RES FUSE ½ W 0.33R J
<Spare Parts order>
VE- 30001235: RES FUSE ½ W 0.33R J
<Start Date of Modification on Production.>
31.05.2002 (Related Changing Form: 929)
Service BulletinModel:AK36 and AK46 chassis with TP46I-3 CRT board
ServiceBulletin No: 124
Priority( )S. All product.( )A. Items in Customer / Dealer stock / Service return goods.( )B. Customer stock / Units returned for Service.( X)C. Sold items returned for Service.( )D. Only Units returned to this bulletin.( )E. Others
SUBJECT : IC403(STV224X) defects DATE : August 27, 2002
<Objective>Please modify if following symptom occurs.
<Symptom>No picture after switching on due to the IC403 RGB outputs are defected.1.When the picture is only green due to 20. Pin of IC403 CVBS SW pin) is defected.2.When Picture is vertically shifted3.
<Cause>
Spark on CRT1.
No good grounding on Tuner2.
Base and emitter of Q603 is short circuit.3.
<Countermeasures>
After changing the defected IC403, Applied
the following modifications to repair chassis and prevent reoccurence of defects
Modifty TP46I-3 CRT board by insertion BA159 diode between 200V and RGB driver resistors as 1.
explain below.
Solder the anode of Diode BA159 (VE-30001318) to cathode of D902; solder the cathode of Diode
BA159 to Q909 collector (intersection point with R913).
Solder the anode of Diode BA159 (VE-30001318) to cathode of D903; solder the cathode of Diode
BA159 to Q908 collector (intersection point with R914).
Solder the anode of Diode BA159 (VE-30001318) to cathode of D901; solder the cathode of Diode
BA159 to Q907 collector (intersection point with R915).
Connect a Diode zener 8.2V (VE-30001347) between the Emitter of Q2 ( - point of C424) and – point 2.
of C485 in order to good grounding on Tuner as explain below.
Solder cathode of Diode Zener to the Emitter of Q2 (- point of C424), solder anode of Diode Zener to –
point of C485.
Connect a Diode zener 8.2V (VE-30001347) between the Collector of Q603 and ground for Vertical 3.
shift problem
Solder cathode of Diode Zener to the Collectorr of Q603, solder anode of Diode Zener to Ground.
<Parts order>
VE-30001318: DIODE BA159 1A/800V 20A VE-30001347: DIODE ZENER 8.2V
<Modification Start Date>
Service Bulletin Model:
All models with AK36 Chassis. Service
Bulletin No: 125
Priority ( )S. All product. ( )A. Items in Customer / Dealer stock / Service return goods. ( )B. Customer stock / Units returned for Service. ( )C. Sold items returned for Service. ( X )D. Only Units returned to this bulletin. ( )E. Others
SUBJECT : Q 602 defect DATE : August 07, 2002
<Objective> Please modify if following symptom occurs
<Symptom> TV does not work due to Q602 broke down
<Cause> Hor. Transistor Driving Condition during switching ON/OFF.
<Countermeasures>
After changing the defected Q602,
In order to improve Q602 resistant to sparks, modify the chassis as given below.
Solder RES CF 1/4W 10K J BETWEEN BASE AND COLLECTOR OF Q601 (Hor.driver Transistor ) as
shown in below.
<Spare Parts order>
RES CF 1/4W 10K J : VE-30000471
<Start Date of Modification on Production.> 16.08.2002
Service BulletinModel:
All models with AK36 Chassis.
ServiceBulletin No: 143
Priority( )S. All products.( )A. Items in Customer / Dealer stock / Service return goods.( )B. Customer stock / Units returned for Service.( X)C. Sold items returned for Service.( )D. Only Units returned to this bulletin.( )E. Others
SUBJECT : Improvement against to the spike on the main supply DATE : Oct 30, 2002
<Objective>Please modify if following symptom occurs
<Symptom>There is no picture on the TVs.
<Cause>The spikes on the main supply are damaged to IC403 (Vertical output IC).
<Countermeasures>
Apply that modification:
Remove D409 from the chassis,
D409: DIODE 1N4148 ==> Not Connected
<Spare Parts order>
VE-30001284: DIODE 1N4148
<Start Date of Modification on Production.>
01.12.2002 (Related Changing Form: 1717)
Service BulletinModel:
All models with AK36 Chassis.
ServiceBulletin No: 146
Priority( )S. All products.( )A. Items in Customer / Dealer stock / Service return goods.( )B. Customer stock / Units returned for Service.( X)C. Sold items returned for Service.( )D. Only Units returned to this bulletin.( )E. Others
SUBJECT : Improvement for Horizontal Size Range DATE : Nov 11, 2002
<Objective>Please modify if following symptom occurs
<Symptom>After changing the CRT, Hor. Size range is not correct.
<Cause>Some Component tolerances.
<Countermeasures>
Apply that modification:
Replace;
R803: RES SMD 1/10W 22K J ==> RES SMD 1/10W 22K F
R801: RES CF 1/4W 4.7K ==> RES MF 1/4W 4.7K
<Spare Parts order>
VE-30007207 : RES SMD 1/10W 22K F for R803
VE-30000983 : RES MF 1/4W 4.7K for R801
<Start Date of Modification on Production.>
11.11.2002 (Related Changing Form: 1711)