7
1 11 05-17 SUBJECT DATE EPA10, GHG14 and GHG17 Diesel Particulate Filters November 2017 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0083 EPA10 Heavy Duty EPA10 Diesel Particulate Filter Re-Fit Procedure These are new sections. GHG14 Heavy Duty GHG14 Diesel Particulate Filter Re-Fit Procedure DDC-SVC-MAN-0190 GHG17 Heavy Duty GHG17 Diesel Particulate Filter Re-Fit Procedure 11 05-17 All information subject to change without notice. 3 11 05-17 Copyright © 2017 DETROIT DIESEL CORPORATION

11 05-17 1 11 05-172 EPA10 Diesel Particulate Filter Re-Fit Procedure In some cases, ... NOTICE: DO NOT hit the 2x4 with a hammer as it could cause damage to the cone. NOTICE: The

  • Upload
    others

  • View
    1

  • Download
    0

Embed Size (px)

Citation preview

  • 1 11 05-17

    SUBJECT DATE

    EPA10, GHG14 and GHG17 Diesel Particulate Filters November 2017

    Additions, Revisions, or Updates

    Publication Number / Title Platform Section Title Change

    DDC-SVC-MAN-0083

    EPA10Heavy Duty

    EPA10 Diesel ParticulateFilter Re-Fit Procedure

    These are new sections.GHG14

    Heavy Duty

    GHG14 DieselParticulate Filter Re-Fit

    Procedure

    DDC-SVC-MAN-0190GHG17

    Heavy Duty

    GHG17 DieselParticulate Filter Re-Fit

    Procedure

    11 05-17

    All information subject to change without notice. 311 05-17 Copyright © 2017 DETROIT DIESEL CORPORATION

  • 2 EPA10 Diesel Particulate Filter Re-Fit Procedure

    In some cases, the inboard Diesel Particulate Filter (DPF) cone on a replacement 1-BOX ™ configuration can move duringshipping, causing the DPF not to fit into the opening. Complete this procedure to properly move the shifted cone and installthe DPF.

    Check as follows:

    1. Using a 9 inch C-clamp (or larger) along with a 2x4 piece of wood, place the 2x4 along the DPF outlet cone as seenbelow.

    NOTICE: DO NOT hit the 2x4 with a hammer as it could cause damage to the cone.

    NOTICE: There are two different length DPFs for EPA10 replacement boxes. Measure the distance of the DPF todetermine the proper desired length between the Diesel Oxidation Catalyst (DOC) and the DPF cone.• Desired distance for short DPFs is 289 mm (11.4 in.). DPF length is 283.6 mm (11.16 in.).• Desired distance for long DPFs is 339mm (13.35 in.). DPF length is 333.6 mm (13.13 in.).Exceeding the desired distance between the DOC and DPF cone could lead to exhaust leaks internal to the 1-BOX ™.

    2. Carefully hand-tighten the C-clamp until the desired distance between the DOC and DPF cone is achieved.3. Remove the C-clamp and 2x4 from the 1-BOX ™.

    2 EPA10 Diesel Particulate Filter Re-Fit Procedure

    4 All information subject to change without notice.Copyright © 2017 DETROIT DIESEL CORPORATION 11 05-17

  • 4. Install the DPF. Refer to section "Installation of the EPA10 Diesel Particulate Filter".

    11 05-17

    All information subject to change without notice. 511 05-17 Copyright © 2017 DETROIT DIESEL CORPORATION

  • 3 GHG14 Diesel Particulate Filter Re-Fit Procedure

    In some cases, the inboard Diesel Particulate Filter (DPF) cone on a replacement 1-BOX ™ configuration can move duringshipping, causing the DPF not to fit into the opening. Complete this procedure to properly move the shifted cone and installthe DPF.

    Check as follows:

    1. Using a 9 inch C-clamp (or larger) along with a 2x4 piece of wood, place the 2x4 along the DPF outlet cone as seenbelow.

    NOTICE: DO NOT hit the 2x4 with a hammer as it could cause damage to the cone.

    NOTICE: The desired distance between the Diesel Oxidation Catalyst (DOC) and DPF cone is 289 mm (11.4 in.).Exceeding 289 mm (11.4 in.) could lead to exhaust leaks internal to the 1-BOX ™.

    2. Carefully hand-tighten the C-clamp until the desired distance between the DOC and DPF cone is achieved.3. Remove the C-clamp and 2x4 from the 1-BOX ™.

    3 GHG14 Diesel Particulate Filter Re-Fit Procedure

    6 All information subject to change without notice.Copyright © 2017 DETROIT DIESEL CORPORATION 11 05-17

  • 4. Install the DPF. Refer to section "Installation of the GHG14 Diesel Particulate Filter ".

    11 05-17

    All information subject to change without notice. 711 05-17 Copyright © 2017 DETROIT DIESEL CORPORATION

  • 4 GHG17 Diesel Particulate Filter Re-Fit Procedure

    In some cases, the inboard Diesel Particulate Filter (DPF) cone on a replacement 1-BOX ™ configuration can move duringshipping, causing the DPF not to fit into the opening. Complete this procedure to properly move the shifted cone and installthe DPF.

    Check as follows:

    1. Using a 9 inch C-clamp (or larger) along with a 2x4 piece of wood, place the 2x4 along the DPF outlet cone as seenbelow.

    NOTICE: DO NOT hit the 2x4 with a hammer as it could cause damage to the cone.

    NOTICE: The desired distance between the Diesel Oxidation Catalyst (DOC) and DPF cone is 289 mm (11.4 in.).Exceeding 289 mm (11.4 in.) could lead to exhaust leaks internal to the 1-BOX ™.

    2. Carefully hand-tighten the C-clamp until the desired distance between the DOC and DPF cone is achieved.3. Remove the C-clamp and 2x4 from the 1-BOX ™.

    4 GHG17 Diesel Particulate Filter Re-Fit Procedure

    8 All information subject to change without notice.Copyright © 2017 DETROIT DIESEL CORPORATION 11 05-17

  • 4. Install the DPF. Refer to section "Installation of the 1-BOX™ Diesel Particulate Filter".

    11 05-17

    All information subject to change without notice. 911 05-17 Copyright © 2017 DETROIT DIESEL CORPORATION

    1 11 05-172 EPA10 Diesel Particulate Filter Re-Fit Procedure3 GHG14 Diesel Particulate Filter Re-Fit Procedure4 GHG17 Diesel Particulate Filter Re-Fit Procedure