Upload
ricocheto
View
341
Download
13
Tags:
Embed Size (px)
Citation preview
Standard STD 101-0005 Volvo Group
Established October 2005 Version 4 Page 1(20)
The English language version is the original and the reference in case of dispute.
Den engelska språkversionen är originalversion och skall åberopas i händelse av tvist.
BASIC RULES FOR REPRESENTATION GRUNDREGLER FÖR REPRESENTATION
Symbols, designations and general drawing methods
Symboler, beteckningar och allmänt ritsätt
Orientation Orientering This standard is based on Volvo corporate standard STD 5023,501, which it replaces in applicable parts.
Denna standard baserar sig på Volvo koncern-standard STD 5023,501 som den ersätter i tillämpliga delar.
To completely cover the scope of STD 5023,501, this standard shall be referred to together with STD 5023,503 in accordance with the description in section 14.1. Within Renault Trucks, this standard can be referred to together with RT standard 01.00.4527.
För att fullständigt täcka omfattningen av STD 5023,501 skall denna standard vara hänvisad till tillsammans med STD 5023,503 i enlighet med beskrivning i avsnitt 14.1. Inom Renault Trucks kan denna standard refereras till tillsammans med RT standard 01.00.4527.
This version differs from version 3 in that section 12 has been added. The section covers indications in accordance with the new common standard STD 180-0001 – Welding of metallic materials. Due to this addition, the subsequent sections have been renumbered.
Denna version skiljer sig från version 3 genom att avsnitt 12 har tillkommit. Avsnittet behandlar angivelsesätt enligt den nya gemensamma stan-darden STD 180-0001 – Svetsning av metalliska material. På grund av detta tillägg har de efterföljande avsnitten numrerats om.
Contents Innehåll 1 Scope and field of application 1 Omfattning och tillämpning
2 General rules on drawing data 2 Allmänna regler om ritningsdata
3 Projection methods and cutting planes 3 Projektionsmetoder och snittplan
4 Lines, points, surfaces and markings 4 Linjer, punkter, ytor och markeringar
5 Simplified representation of machine elements
5 Förenklad ritning av maskinelement
6 Dimensioning 6 Måttsättning
7 Tolerances 7 Toleranser
8 Surface texture 8 Ytstruktur
9 Critical characteristics of design parts 9 Kritiska egenskaper för konstruerade artiklar
10 Marking of parts 10 Artikelmärkning
11 Hardness and case depth 11 Hårdhet och härddjup
12 Welding 12 Svetsning
13 Information in the drawing sheet blocks 13 Uppgifter i fälten på ritningsblanketten
14 Reference to this standard 14 Hänvisning till denna standard
Standard STD 101-0005 Volvo Group
Version 4 Page 2
1 Scope and field of application 1 Omfattning och tillämpning This standard contains graphic symbols, designations of, e.g. tolerances, hardness and case depth as well as general examples of drawing methods used on drawings produced within the Volvo Group or at the request of some individual company within the Volvo Group. The standard refers also to those Volvo Group common standards and ISO standards that give a complete definition of the representations shown.
Denna standard innehåller grafiska symboler, be-teckningar av exempelvis toleranser, hårdhet och härddjup samt generella exempel på ritsätt vilka används på ritningar som produceras inom Volvo-koncernen eller på uppdrag av något enskilt koncern-företag. Standarden hänvisar vidare till de Volvo-gemensamma standarder eller ISO-standarder som ger en fullständig definition av visade angivelser.
In certain cases, the specific drawing methods are established by this standard only.
I vissa fall är de specifika ritsätten endast fastställda genom denna standard.
In section 2 with sub-sections, a number of basic and general rules concerning the interpretation of drawings are stated. In addition, general requirements for toleranced properties are specified.
I avsnitt 2 med underavsnitt anges ett antal allmänna och grundläggande regler rörande tolkning av ritningar. Vidare specificeras allmänna krav för toleranssatta egenskaper.
By referring to this standard on drawings: Genom hänvisning till denna standard på ritning:
− the requirements specified in the standards that are indicated under the heading "Established by standard" in the following sections apply
− gäller krav enligt de standarder som anges under rubriken "Fastställd i standard" i de följande avsnitten
− it is possible to interpret the indications that the standard gives examples of.
− är det möjligt att tolka de angivelser som standar-den ger exempel på.
In those cases the drawing method used is not exemplified in this standard, reference to the standard applied shall always be given on the relevant drawing.
Där använd ritningsangivelse inte finns exemplifierad i denna standard, skall hänvisning till tillämpad standard alltid finnas på den aktuella ritningen.
If a drawing refers to a standard that conflicts with a standard within the body of STD 101-0005, then the standard noted on the drawing shall have priority.
Om en ritning refererar till en standard som är motstridig till en standard som åberopas i STD 101-0005 skall den standard som angivits på ritningen ha prioritet.
With the exception of those cases when this standard establishes a specific drawing method, the standard gives only a simplified explanation of the respective drawing indication. For a complete interpretation, the standards referred to in connection with the respective example always apply.
Med undantag för de fall där denna standard fast-lägger ett specifikt ritsätt ger standarden endast en förenklad förklaring av respektive ritningsangivelse. För fullständig tolkning gäller alltid de standarder vilka hänvisas till i anslutning till respektive exempel.
In case of any discrepancy between the indications given in this standard and the standards referred to for full interpretation, the latter always apply.
Vid eventuella skiljaktigheter mellan angivelser i den-na standard och de standarder som angetts för deras tolkning, gäller alltid de senare.
2 General rules on drawing data 2 Allmänna regler om ritningsdata Unless otherwise stated on the drawing or in the associ-ated document, dimensions are given in millimetres.
Om inget annat angivits på ritning eller i annat tillhö-rande dokument är måttuppgifter uttryckta i millimeter.
Unless otherwise indicated, generally or for a single piece of information, the technical documentation represents the object in its finished condition.
Om inget annat angivits, generellt eller för enskild uppgift, återger det tekniska underlaget objektet i sitt färdiga utförande.
The only exception from this rule is surface coated M-threads where the tolerance applies before any surface coating.
Enda undantaget från denna regel är M-gängor där toleransen gäller före eventuell ytbeläggning.
Standard STD 101-0005 Volvo Group
Version 4 Page 3
Scale Unless otherwise indicated generally on the drawing, main scale 1:1 has been applied. A locally indicated scale applies only to the view or section concerned.
Skala Om inget annat angivits generellt på ritningen, har huvudskala 1:1 tillämpats. En lokalt angiven skala gäller endast berörd vy eller berört snitt.
2.1 Principles for tolerance requirements
2.1 Principer för toleranskrav
For all toleranced properties on drawings and in associated documentation, STD 110-0001 Principles for tolerance requirements applies.
För alla toleranssatta egenskaper på ritning och i tillhörande dokumentation gäller STD 110-0001 Principer för toleranskrav.
3 Projection methods and cutting planes
3 Projektionsmetoder och snittplan
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
Principle / Princip
C
B
D
A
The arrow method. Layout of views according to the reference arrow method/ Pilmetoden. Vyplacering enligt metod med riktningspilar
ISO 128-30:2001
1
Method E. First angle projection method/ Metod E. Första kvadrantens projektions- metod
ISO 128-30:2001
Method A. Third angle projection method/ Metod A. Tredje kvadrantens projektions- metod
ISO 128-30:2001
Drawing and dimensioning in axonometric representation/ Ritning och måttsättning i axonometrisk representation
STD 101-0002
Standard STD 101-0005 Volvo Group
Version 4 Page 4
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
A
A
Indication of cutting plane/ Markering av snittplan
ISO 128-40:2001
4 Lines, points, surfaces and markings
4 Linjer, punkter, ytor och markeringar
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
General use and meaning of lines/ Linjers allmänna användning och betydelse
ISO 128-24:1999
Partial view of a symmetrical object. Two alternative methods of presentation/ Delvy av symmetriskt objekt. Två alternativa ritsätt
ISO 128-24:1999
Interrupted views. Two alternative methods of presentation/ Brutna vyer. Två alternativa ritsätt
ISO 128-24:1999
Outline before forming (in this case before bending)/ Kontur före bearbetning (i detta fall före bock-ning)
ISO 128-24:1999
Standard STD 101-0005 Volvo Group
Version 4 Page 5
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
Indication of outline of an adjacent part/ Markering av kontur för intilliggande objekt
ISO 128-24:1999
Indication of trajectories and alternative or ex-treme positions for movable parts/ Markering av bana för rörelse och alternativt eller extremt läge för rörlig del
ISO 128-24:1999
Indication of square surfaces and ends/ Markering av fyrkantiga ytor och ändar
ISO 128-24:1999
Indication of fluid in section/ Markering av vätska i snitt
Established by this standard/ Fastställd genom denna standard
5 Simplified representation of machine elements
5 Förenklad ritning av maskin-element
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
Representation of screw threads/ Ritning av gängor ← External visible screw threads/ Utvändiga synliga gängor
ISO 6410-1:1993
← Internal hidden screw threads/ Invändiga skymda gängor
Standard STD 101-0005 Volvo Group
Version 4 Page 6
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
← Section through internal screw threads/ Snitt genom invändiga gängor
ISO 6410-1:1993
Representation of gears / Ritning av kuggar
ISO 2203:1973
Symbols for gear type and direction/ Symboler för kuggtyp och riktning ← Helical to the right and to the left/ Snedkugg höger och vänster ← Double helical / Dubbel snedkugg ← Spiral / Bågkugg
Representation of splines and serrations/ Ritning av splines och serrationer Symbol for / Symbol för: ← Straight-sided splines/ Splines med rak profil ← Involute splines and serrations/ Evolventsplines och serrationer
ISO 6413:1988
A) B) C)
General simplified representation of dynamic seals/ Allmänt förenklad ritning av dynamiska tätningar: A) Sealing direction of no importance/ Tätningsriktning saknar betydelse B) Sealing direction (in the direction of the arrow)/ Tätningsriktning (i pilens riktning) C) Exact contour shown / Verklig kontur visad
ISO 9222-1:1989
Standard STD 101-0005 Volvo Group
Version 4 Page 7
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
Detailed simplified representation of lip type seals (radial seals)/ Detaljerad förenklad ritning av radialtätningar: ← Rotary shaft seal without dust lip/ Tätning utan dammtunga för roterande axel
ISO 9222-2:1989
← Seal without dust lip for stationary shaft and rotary housing/ Tätning utan dammtunga för stillastående axel och roterande hus
← Rotary shaft seal with dust lip/ Tätning med dammtunga för roterande axel
← Rotary shaft seal with dust lip (double- acting)/ Tätning med dammtunga för roterande axel (dubbelverkande)
Detailed simplified representation of lip type seals (radial seals)/ Detaljerad förenklad ritning av radialtätningar: ← Seal with dust lip for stationary shaft and rotary housing/ Tätning med dammtunga för stillastående axel och roterande hus
ISO 9222-2:1989
Detailed simplified representation of axial seals/ Detaljerad förenklad ritning av axialtätningar ← Rotary shaft axial seal/ Axialtätning för roterande axel
ISO 9222-2:1989
Standard STD 101-0005 Volvo Group
Version 4 Page 8
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
Detailed simplified representation of seals for reciprocating movements (piston rod seals)/ Detaljerad förenklad ritning av tätningar för fram- och återgående rörelser (kolvstångs-tätningar):
ISO 9222-2:1989
A) B) C) D)
A) U-cups / U-manschetter B) V packing sets / V-tätningssats C) V-rings / Hattmanschetter D) Wipers / Avstrykare
Detailed simplified representation of labyrinth seals/ Detaljerad förenklad ritning av labyrinttätningar
ISO 9222-2:1989
A) B)
Simplified representation of rolling bearings/ Förenklad ritning av rullningslager Normally drawn in accordance with A). B) shows an example of simplified representation showing the exact outline of the bearing/ Ritas normalt enligt A). B) visar exempel på förenklad ritning där lagrets verkliga kontur visas
ISO 8826-1:1989
Guide pin, guide hole, centre of gravity/ Styrpinne, styrhål, tyngdpunkt
Established by this standard/ Fastställd genom denna standard
6 Dimensioning 6 Måttsättning
6.1 General dimensioning 6.1 Måttsättning allmänt
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
65±0,5
35±0
,5
Dimensioning, general principles/ Måttsättning, allmänna regler
ISO 129:1985
60,5°±1,5°
Dimensioning of angular dimensions/ Måttsättning av vinkelmått
ISO 129:1985
Standard STD 101-0005 Volvo Group
Version 4 Page 9
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
(55) Indication of auxiliary dimensions/ Markering av hjälpmått
ISO 129:1985
50
Indication of arc dimensions/ Markering av bågmått
ISO 129:1985
Origin indication in superimposed running dimensioning/ Nollpunkt vid förenklad baslinjemåttsättning
ISO 129:1985
16
Framed dimensions / Inramade mått:
Theoretically exact dimensions when using geometrical tolerances/ Teoretiskt riktiga mått vid tillämpning av form- och lägetoleranser
STD 112-0003
Setting dimension, gauge dimension for production and inspection. These dimensions shall be considered as having no tolerances/ Inställningsmått, tolkmått för produktion och kontroll. Dessa mått betraktas som toleranslösa
Established by this standard/ Fastställd genom denna standard
F6
F11
Numbering of holes / Hålnumrering Holes designated by letters and figures where/ Hål betecknas med bokstäver och siffror där: T = view from above / vy uppifrån B = view from below / vy underifrån F = front view (principal view)/ vy framifrån (huvudvy) R = view from the rear / vy bakifrån RH = view from the right / vy från höger LH = view from the left / vy från vänster
STD 101-0004
6.2 Symbols in connection with dimensions
6.2 Symboler i samband med mått
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
∅ Diameter ISO 129:1985
R Radius / Radie ISO 129:1985
Square / Kvadrat ISO 129:1985
Standard STD 101-0005 Volvo Group
Version 4 Page 10
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
Oblong hole / Avlångt hål Established by this
standard/ Fastställd genom denna standard
Indication of taper / Angivelse av kona ISO 3040:1990
Rectangular shape / Rektangulär form Fastställd genom denna
standard/ Established by this standard
SR Spherical radius / Sfärisk radie ISO 129:1985
S∅ Spherical diameter / Sfärisk diameter ISO 129:1985CL Centre line / Centrumlinje Established by this
standard/ Fastställd genom denna standard
x Number of equal elements, for example 5x10 for five times the dimension 10/ Antalet lika element, exempelvis 5x10 för fem gånger måttet 10
ISO 129:1985
6.3 Marking of requirements 6.3 Markering av krav
Drawing method Ritsätt
Explanation Betydelse
Established by standardFastställd i standard
A) B)
Indication of a partial requirement, for example hardening/ Markering av partiellt krav, exempelvis härdning
When the extension of the requirement is of no importance or when it is obvious, the dimensioning can be excluded, see figure A) / Är kravets utsträckning oväsentlig eller självklar utelämnas måttsättning, se figur A)
When needed, the special requirement shall be dimensioned, see figure B)/ Vid behov måttsätts det speciella kravet, se figur B)
ISO 129:1985
Standard STD 101-0005 Volvo Group
Version 4 Page 11
7 Tolerances 7 Toleranser
7.1 Dimensional tolerances 7.1 Dimensionstoleranser
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
± 0,5 Tolerance for linear dimension/ Tolerans för linjärt mått
STD 110-0001
+ 1,5° 0
Tolerance for angular dimension (fraction of degree in decimals)/ Tolerans för vinkelmått (del av grad i decimaler)
STD 110-0001
E Envelope requirement / Enveloppkrav STD 110-0001
7.2 Geometrical tolerances and datums 7.2 Form- och lägetoleranser samt referenser
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
Ø0,5 A
Tolerance frame with example of information/ Toleransrektangel med exempel på uppgifter:
← Datum / Referens
← Tolerance value / Toleransvärde
← Toleranced characteristic/ Toleranssatt egenskap
STD 112-0003
Straightness / Rakhet STD 112-0003
Flatness / Planhet STD 112-0003
Roundness / Rundhet STD 112-0003
Cylindricity / Cylindricitet STD 112-0003
Profile of any line / Profilform
Position of any profile / Profilläge (with datum feature / med referenselement)
STD 112-0003
Standard STD 101-0005 Volvo Group
Version 4 Page 12
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
Profile of any surface / Ytform
Position of any surface / Ytläge (with datum feature / med referenselement)
STD 112-0003
Position / Lägeriktighet STD 112-0003
Concentricity, coaxiality/ Koncentricitet, koaxialitet
STD 112-0003
Symmetry / Symmetri STD 112-0003
Parallelism / Parallellitet STD 112-0003
Perpendicularity / Vinkelräthet STD 112-0003
Angularity / Vinkelriktighet STD 112-0003
Run-out / Kast STD 112-0003
Total run-out / Totalkast STD 112-0003
Toleranced profile characteristic applies all around the outline of the workpiece/ Toleranssatt profilegenskap gäller konturen runtom arbetsstycket
STD 112-0003
Ø 0,2 CZ
CZ = Common Zone A single tolerance zone that applies to several separate features/ CZ = gemensamt toleransområde Ett enskilt toleransområde som gäller för flera separata element
STD 112-0003
P
Projected tolerance zone/ Utflyttat toleransområde
STD 112-0003
M
Maximum material principle / Måttjämkning STD 112-0001
L
Least material requirement/ Min materialkrav
ISO 2692:1988/Amd 1:1992
Standard STD 101-0005 Volvo Group
Version 4 Page 13
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
F
Free state condition/ Fritt tillstånd
ISO 10579:1993
Indication of measuring principles/ Angivelse av mätprinciper
Example: measuring principles 2 and 3 Exempel: mätprinciper 2 och 3
STD 112-0004
A
20x20
MP 2
A
AØ
B
MP 3
Indication of datum with datum letter/ Angivelse av referens med referensbokstav
STD 112-0002
Indication of datum without datum letter/ Angivelse av referens utan referensbokstav
STD 112-0002
1
Datum target / Lokal referens
Example: datum target point A1/ Exempel: lokal referenspunkt A1
STD 112-0002
B1
Example: datum target line B1/ Exempel: lokal referenslinje B1
18
Example: datum target area A1, ∅ 8 Exempel: lokal referensarea A1, ∅ 8
2
Example: datum target area B2, 20x20 Exempel: lokal referensarea B2, 20x20
Standard STD 101-0005 Volvo Group
Version 4 Page 14
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
X5Ø25
Datum target for coordinate system (only letters X, Y and Z designating coordinate direction are used)/ Lokal referens för koordinatsystem (endast bokstäverna X, Y och Z, som betecknar koordinatriktning, används)/
Example: datum target area X5, ∅ 25 Exempel: lokal referensarea X5, ∅ 25
STD 101-0003
aY2
Datum target for interface system in coordinate system (interface systems are identified with a small letter preceding the coordinate letter)/ Lokal referens för interface-system i koordinat-system (interface-system identifieras med en liten bokstav före koordinatbokstav)/
Example: datum target point aY2/ Exempel: lokal referenspunkt aY2
STD 101-0003
7.2.1 Geometrical tolerances for design in coordinate system
7.2.1 Form- och lägetoleranser för konstruktioner i koordinatsystem
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
XYZ
Datum targets for coordinate systems as datums/ Lokala referenser för koordinatsystem som referens
STD 112-0006
XYZ+2- 1
+
_
Assymetrical tolerance zone/ Osymmetriskt toleransområde
STD 112-0006
XYZ+2 / -1+
_
Alternative indication/ Aternativt skrivsätt
XYZ2
A B
Tolerance for a restricted length (between A and B)/ Tolerans för delsträcka (mellan A och B)
STD 112-0006
XYZ
XYZ
2
1
Location tolerance with orientation requirement for a surface/ Lägetolerans med riktningskrav för en yta
STD 112-0006
Standard STD 101-0005 Volvo Group
Version 4 Page 15
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
XYZ
XYZ
2
1
Location tolerance with orientation requirement for an edge line/ Lägetolerans med riktningskrav för en kantlinje
STD 112-0006
5±2CV 1
Requirement on clearance variation (CV)/ Krav på spelvariation (CV)
STD 112-0006
8 Surface texture 8 Ytstruktur
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
A) Basic graphical symbol for surface texture/ Grundläggande grafisk symbol för ytstruktur
B) Expanded graphical symbol indicating removal of material required/ Utökad grafisk symbol som anger att material skall avverkas
A) B) C)
C) Expanded graphical symbol indicating removal of material not permitted/ Utökad grafisk symbol som anger att materialavverkning inte är tillåten
STD 120-0004
Complete graphical symbol where a line has been added. Complementary requirements for surface texture characteristics are specified in connection to this symbol/ Komplett grafisk symbol då en linje lagts till. Kompletterande krav på ytstrukturens egenskaper ges i anslutning till denna symbol
STD 120-0004
Ra 3,2 Rz 6,3
Examples of complete graphical symbols with complementary requirements/ Exempel på kompletta grafiska symboler med kompletterande krav
STD 120-0004
0,008-0,8 / Rmr0 3 / Rmr(2) 3 50
Example of a indication of bearing ratio requirements for R-profile. Bearing ratio requirements may also be specified for W- and P-profiles/ Exempel på angivning av bärighetskrav för R-profil. Krav på bärighet kan äve anges för W- och P-profil
STD 120-0005
Standard STD 101-0005 Volvo Group
Version 4 Page 16
9 Critical characteristics of design parts
9 Kritiska egenskaper för konstruerade artiklar
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
[1] Criticality 1/ Allvarlighetsgrad 1
STD 105-0001
[2] Criticality 2/ Allvarlighetsgrad 2
STD 105-0001
[3] Criticality 3/ Allvarlighetsgrad 3
STD 105-0001
10 Marking of parts 10 Artikelmärkning
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
Requirement for marking of parts Krav på artikelmärkning
STD 103-0007
11 Hardness and case depth 11 Hårdhet och härddjup
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
350 HBW
Designation of Brinell hardness/ Beteckning för Brinellhårdhet:
Brinell hardness 350 determined with a hard metal ball/ Brinellhårdhet 350 bestämd med hård-metallkula
STD 323-0001
600 HBW 5/750/20
When needed, the designation is supple-mented with/ Vid behov kompletteras beteckningen med:
← Ball diameter (mm) / Kuldiameter (mm)
← Mass (kg) that yields the test force/ Massa (kg) som åstadkommer provkraften
← Duration of test force application (s)/ Hålltid (s)
Standard STD 101-0005 Volvo Group
Version 4 Page 17
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
59 HRC
Designation of Rockwell hardness/ Beteckning för Rockwellhårdhet:
Rockwell hardness 59, measured on the Rockwell C-scale/ Rockwellhårdhet 59 bestämd enligt Rockwellskala C
STD 323-0002
640 HV
Designation of Vickers hardness/ Beteckning för Vickershårdhet:
← Vickers hardness 640 / Vickershårdhet 640
STD 323-0003
640 HV 30/20
When needed, the designation is supple-mented with/ Vid behov kompletteras beteckningen med: ← Mass (kg) that yields the test force/ Massa (kg) som åstadkommer provkraften ← Duration of test force application (s)/ Hålltid (s)
DC = 1,2 ± 0,3
Designation of case-hardened depth/ Beteckning för sätthärdningsdjup:
← Case-hardened depth 1,2±0,3/ Sätthärdningsdjup 1,2±0,3
STD 322-0002
+ 0,2 DC 650 = 0,4 - 0,1
Requirement for another hardness limit for the case-hardened depth than 550 HV shall be indicated as in the example below/ Krav på annan gräns för sätthärdningsdjupet än 550 HV anges enligt nedanstående exempel:
← Case-hardened depth 0,4+0,2/-0,1 at 650 HV/ Sätthärdningsdjup 0,4+0,2/-0,1 vid 650 HV
DI = 2 ± 1
Designation of induction-hardened depth/ Beteckning för induktionshärdningsdjup:
← Induction-hardened depth 2±1/ Induktionshärdningsdjup 2±1
STD 322-0001
DI 500 = 2 ± 1
Requirement for another hardness limit for the induction-hardened depth than 400 HV shall be indicated as in the example below/ Krav på annan gräns för induktions-härdningsdjupet än 400 HV anges enligt nedanstående exempel:
← Induction-hardened depth 2±1 vid 500 HV/ Induktionshärdningsdjup 2±1 at 500 HV
Standard STD 101-0005 Volvo Group
Version 4 Page 18
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
DNC = 0,3 MIN
Designation of nitrocarburizing depth/ Beteckning för nitrokarbureringsdjup:
← Nitrocarburizing depth 0,3 MIN/ Nitrokarbureringsdjup 0,3 MIN
STD 322-0004
DN = 0,4 ± 0,1
Designation of nitriding depth/ Beteckning för nitrerdjup:
← Nitrerdjup 0,4±0,1/ Nitriding depth 0,4±0,1
STD 322-0003
12 Welding 12 Svetsning Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
1)2)
3) 4)
Weld ASvets A
Weld BSvets B
1) 3)
2) 4)
Designation / Beteckning
Examples of arrow side and other side/ Exempel på pilsida och bortre sida:
1) Arrow side for weld A/ Pilsida för svets A 2) Other side for weld A/ Bortre sida för svets A 3) Arrow side for weld B/ Pilsida för svets B 4) Other side for weld B/ Bortre sida för svets B
STD 180-0001
a5a5
8x907x90
(200)(200)
11 - B [3]
Example of a symbolic representation of weld/ Exempel på svetsbeteckning:
← Criticality / Allvarlighetsgrad ← Welding class / Svetsklass ← Welding process / Svetsmetod ← Distance between weld elements/ Avstånd mellan delsvetsar ← Symbol for staggered intermittent weld/ Symbol för sicksacksvets ← Length of weld elements / Delsvetslängd ← Number of weld elements / Antal delsvetsar ← Supplementary symbol / Tilläggssymbol ← Elementary symbol / Grundsymbol ← Dimension of weld cross-section/ Mått på svetsens tvärsnitt
STD 180-0001
Standard STD 101-0005 Volvo Group
Version 4 Page 19
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
A) B) C) D)
E) F) G) H)
I) J) K)
Elementary symbols / Grundsymboler:
A) Butt weld between plates with raised edges/ Svets i dubbelflänsad stumfog B) Square butt weld/ Svets i I-fog och svets i kantfog C) Single-V butt weld / Svets i V-fog D) Single-bevel butt weld / Svets i halv V-fog E) Single-U butt weld / Svets i U-fog F) Single-J butt weld / Svets i J-fog G) Backing run / Baksträng H) Fillet weld / Svets i kälfog I) Plug weld / Svets i hålfog J) Spot weld / Punktsvets K) Seam weld / Sömsvets
STD 180-0001
Supplementary symbols / Tilläggssymboler: ← Flat weld / Struken svets
← Convex weld / Rågad svets
← Concave weld / Urgröpt svets
STD 180-0001
Complementary indications/ Kompletterande beteckningar: ← Site weld / Montagesvets
← Peripheral weld (all around a part)/ Svets runt om ett objekt
STD 180-0001
13 Information in the drawing sheet blocks
13 Uppgifter i fälten på ritnings-blanketten
For interpretation of information in the title and revision blocks of the drawing sheet with title block in accordance with figure 1, STD 910-0001 is referred to.
För tolkning av uppgifter i ritningsblankettens huvud- respektive ändringsfält på ritningsblanketter med huvudfält enligt figur 1, hänvisas till STD 910-0001.
Standard STD 101-0005 Volvo Group
Version 4 Page 20
The copying, distribution and utilization of this document as well as the communication of its contents to others without expressed authorization is prohibited. Offenders will be held liable for payment of damages. All rights reserved in the event of the grant of a patent, utility model or ornamental design registration.
Document title
Document type
Document No Issue Sheet No
Owner domain:Document prefix
Fig. 1 - The form exists in a number of versions with the same layout but with different company names Blanketten finns i ett antal versioner med samma layout men med olika företagsnamn
14 Reference to this standard 14 Hänvisning till denna standard For the application of this standard, a reference shall be given in the text block of the drawing in accordance with below.
Vid tillämpning av denna standard skall hänvisning ges genom not i ritningens skrivfält enligt nedan:
SYMBOLS, DESIGNATIONS AND GENERAL DRAWING METHODS STD 101-0005
14.1 Reference to this standard in combination with STD 5023,503
14.1 Hänvisning till denna standard i kombination med STD 5023,503
When symbols, designations and general drawing methods according to this standard as well as those covered by standard STD 5023,503 apply, reference to both standards shall be given in the text block of the drawing in accordance with below.
Vid tillämpning av symboler, beteckningar och ritsätt i denna standard samt även de som täcks av standard STD 5023,503, skall hänvisning till båda dessa standarder ges genom not i ritningens skrivfält enligt nedan:
SYMBOLS, DESIGNATIONS AND GENERAL DRAWING METHODS STD 101-0005 AND STD 5023,503