Cast Iron Soil Pipe Products

SUBMITTAL

Hubless Pipe & Fittings

J

T

B

HUBLESS PIPE 10 FEET*

NOM. SIZE

BINSIDE

DIAMETER

JOUTSIDE

DIAMETER

T WT (LBS.)NOM. MIN

1 1/2 1.50 1.90 0.16 0.13 28.42 1.96 2.35 0.16 0.13 36.33 2.96 3.35 0.16 0.13 52.14 3.94 4.38 0.19 0.15 77.25 4.94 5.30 0.19 0.15 95.66 5.94 6.30 0.19 0.15 113.58 7.94 8.38 0.23 0.17 181.910 10.00 10.56 0.28 0.22 276.712 11.94 12.50 0.28 0.22 364.215 15.11 15.83 0.36 0.30 542.0

*All dimensions in inches except where indicated. Note: All dimensions and tolerances are from ASTM A-888 and CISPI 301 Hubless Pipe & Fittings.

10 FEET

APPROvALS & STANDARDS• UPC Listed through IAPMO R&T laboratory• CertifiedtoconformtoASTM A888-StandardSpecificationforHublessCastIronSoilPipeandFitttingsforSanitary

andStormDrain,Waste,andVentPipingApplicationsthroughIAPMOR&Tlaboratory• CertifiedtoconformtoCISPI 301-StandardSpecificationsforHublessCastIronSoilPipeandFittingsforSanitaryand

StormDrain,Waste,andVentPipingApplicationsthroughIAPMOR&Tlaboratory• Star®PipeProductsHublessCastIronSoilPipeandFittingsmeettherequirementsofICC International Plumbing

Code 2006formaterialsasoutlinedinChapter7forsanitarydrainagesystems(sections702,705,&708)• OSHPD compliant as per CANs 2001 and CANs2007 as per CPC section 701.1

Quarter Bend Double Quarter Bend P-Trapw/ 1/2" Primer Tap

San Cross

Wye ShortReducer

San TeeDouble Combination Wye & 1/8" Bend

Manufacturer’s

www.starpipeproducts.com ®REGISTEREDTRADEMARKOFSTARPIPEPRODUCTS

STAR®PIPEPRODUCTS-PLUMBING DIvISION4018WestHollowParkway▪Houston,TX77082

1-877-909-7827FAX866-868-7827

QUALITY SYSTEM

REG I S T R ATION

® REGISTERED TRADEMARK OF STAR PIPE PRODUCTS

STAR® PIPE PRODUCTS - PLUMBING DIVISION4018 West Hollow Parkway ▪ Houston, TX 77082

1-877-909-7827 FAX 866-868-7827

Cast Iron Soil Pipe Products

SUBMITTAL

Hub & Spigot Pipe & FittingsService Weight (SV)

*All dimensions in inches except where indicated. Note: All dimensions and tolerances are from ASTM A-74

APPrOVALS & STANDArDSUPC Listed• through IAPMO R&T laboratoryCertified to conform to • ASTM A-74 - Standard Specification for Cast Iron Soil Pipe and FitttingsStar• ® Pipe Products SV Cast Iron Soil Pipe and Fittings meet the requirements of ICC International Plumbing Code 2006 for materials as outlined in Chapter 7 for sanitary drainage systems (sections 702, 705, & 708).SV Gaskets conform to ASTM C564 - Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe & Fittings.•

www.starpipeproducts.com

DETAILS OF HUB & SPIGOT FOr SV*INSIDE

DIAMETEr HUB

INSIDE DIAMETEr

BArrEL

OUTSIDE DIA.OF BArrEL THICKNESS OF BArrEL TELESCOPING

LENGTH

NOM.SIZE A B C J T-NOM T-MIN Y

2 2.94 ±0.06 1.96 ±0.09 3.62 2.30 ±0.09 0.17 0.14 2.50 ±0.09

3 3.94 +0.09-0.06 2.96 ±0.09 4.68 3.30 ±0.09 0.17 0.14 2.75 ±0.09

4 4.94 +0.09-0.06 3.94 ±0.09 5.68 4.30 ±0.09 0.18 0.15 3.00 ±0.09

5 5.94 +0.09-0.06 4.94 ±0.09 6.68 5.30 ±0.09 0.18 0.15 3.00 ±0.09

6 6.94 +0.09-0.06 5.94 ±0.09 7.68 6.30 ±0.09 0.18 0.15 3.00 ±0.09

8 9.25 ±0.13 7.94 ±0.13 10.13 8.38 ±0.13 0.23 0.17 3.50 ±0.13

10 11.38 ±0.13 9.94 ±0.13 12.44 10.50 ±0.13 0.28 0.22 3.50 ±0.13

12 13.50 ±0.13 11.94 ±0.19 14.56 12.50 ±0.19 0.28 0.22 4.25 ±0.19

15 16.95 ±0.13 15.16 ±0.19 18.11 15.88 ±0.19 0.36 0.22 4.25 ±0.19

3½', 5' & 10'Laying Length

STAR 4" x 10' SV PIPE UPC® ASTM A-74 XXX XXX XXX

Manufacturer’s Registration Trademark

Countryof Origin

Dateof Manufacturing

SHOrT SWEEP BEND - 90º SANITArY TEE P-TrAP WYE COMBINATION WYEAND 1/8 BEND

A

B

Y( Telescoping Length ) Laying Length

J

T

C

QUALITY

QUALITY SYSTEM

REG I S T R ATION

Cast Iron Soil Pipe Products

SUBMITTAL

Standard 60 Coupling

Standard 60 Coupling

STAndArdS & SpeCIfICATIonS• CertifiedtocomplywithASTMC1277StandardSpecificationforHublessCouplings.

• ListedthroughIAPMOfile#6200forcompliancetoUPCandASTMC1277.

• GasketcomplieswithASTMC564.

• CouplingsconformtoCISPI310.

feATUreS• 3rd party Listed to ASTM C1277 Standards: Independently3rdpartylisted byIAPMOforcomplianceto

theASTMC1277standardforhublesscouplings(file#6200).

• Clamp Assembly: AllStainlessSteelclampassemblyfeaturesbandsrivetedtotheshieldwithboth

fixedandflexiblestainlesssteeleyelets.

• optimum Shield design: Corrugatedpatternbrightannealedstainlesssteelshieldeffectivelytransfers

compressionevenlythroughthegasketprovidinganimprovedsealandrestraintcapability.

• Gasket:ManufacturedfrompremiumvirginNeopreneelastomerresultinginsuperiorperformance

characteristicsunderawiderangeofinstallationconditions.

www.starpipeproducts.comREV:090209-02

®REGISTEREDTRADEMARKOFSTARPIPEPRODUCTS

STAR®PIPEPRODUCTS-pLUMBInG dIVISIon4018WestHollowParkway▪Houston,TX77082

1-877-909-7827FAX866-868-7827

MATerIALSSHIELD: Type301AISIStainlessSteel,BrightAnnealed

BAND: Type301AISIStainlessSteel

SCREWHOUSING: Type301AISIStainlessSteel

SCREW: Type305AISIStainlessSteel,5/16”hexhead

EYELETS: Type300AISIStainlessSteel,fixedandflexible

GASKET: Neopreneelastomer

STAndArd 60 noM. ITeM # of BAndS InSTALLATIon

SIZe (In.) Code per CoUpLInG TorQUe (In.-LBS.)

11⁄2 NHC0150SD 2 60

2 NHC0200SD 2 60

3 NHC0300SD 2 60

4 NHC0400SD 2 60

5 NHC0500SD 4 60

6 NHC0600SD 4 60

8 NHC0800SD 4 60

10 NHC1000SD 4 60

Cast Iron Soil Pipe Products

SUBMITTAL

Heavy 80 Wide Body Coupling

Heavy 80 Wide Body Coupling - Blue Shield

STANDARDS & SPECIFICATIONS• Certifi ed to comply with ASTM C1540 Standard Specifi cation for Heavy Duty Hubless Couplings• Listed through IAPMO fi le #6199 for compliance to UPC and ASTM C1540• FM approved to FM 1680 standard Class I 15 PSI• Gasket complies with ASTM C564

FEATURES3rd Party Listed to ASTM C1540 Standards: • Independently 3rd party listed by IAPMO for compliance to the ASTM C1540 standard for Heavy Duty hubless

couplings (fi le #6199).Engineered Clamp Assembly: • All Stainless Steel clamp assembly features bands riveted to the shield with both fi xed and longer fl exible eyelets.

Screw housing interlocks with the band providing a reliable assembly even when screws are torqued up to 125% of stated installation torque.

• Long fl exible eyelet slot allows increased independent movement of the band while tightening which helps pre-vent shield crimping and results in a coupling suitable for joining pipe and fi ttings with minimum/maximum toler-ance conditions.

Optimum Shield Design: • Through rigorous testing and evaluation, Star engineers have optimized the shield design to provide maximum joint

rigidity, along with the enhanced ability to transfer torque loads to the gasket.• Corrugated pattern bright annealed stainless steel shield effectively transfers compression evenly through the gas-

ket providing an improved seal and restraint capability.Gasket: • Manufactured from premium virgin Neoprene elastomer resulting in superior performance characteristics under a

wide range of installation conditions.

www.starpipeproducts.com ® REGISTERED TRADEMARK OF STAR PIPE PRODUCTS

STAR® PIPE PRODUCTS - PLUMBING DIVISION4018 West Hollow Parkway � Houston, TX 77082

1-877-909-7827 FAX 866-868-7827

MATERIALSSHIELD: Series 300 AISI Bright Annealed Stainless SteelBAND: Series 300 AISI Stainless SteelSCREW HOUSING: Series 300 AISI Stainless SteelSCREW: Type 305 AISI Stainless Steel, 5/16” hex headEYELETS: Series 300 AISI Stainless Steel, fi xed and fl exibleGASKET: Neoprene elastomer

HEAVY 80 WIDE BODYNOM. ITEM # OF BANDS INSTALLATION

SIZE (IN.) CODE PER COUPLING TORQUE (IN.-LBS.)

11⁄2 NHC0150HD 4 80

2 NHC0200HD 4 80

3 NHC0300HD 4 80

4 NHC0400HD 4 80

5 NHC0500HD 6 80

6 NHC0600HD 6 80

8 NHC0800HD 6 80

10 NHC1000HD 6 80

REV:090209-03

APPROVED

Cast Iron Soil Pipe Products

SUBMITTAL

Super Heavy 80 Wide Body Coupling

Super Heavy 80 Wide Body Coupling - Red Shield

STANDARDS & SPECIFICATIONS• Certifi ed to comply with ASTM C1540 Standard Specifi cation for Heavy Duty Hubless Couplings• Listed through IAPMO fi le #6199 for compliance to UPC and ASTM C1540• FM approved to FM 1680 standard Class I 15 PSI• Gasket complies with ASTM C564

MATERIALSSHIELD Type 304 AISI Bright Annealed Stainless SteelBAND: Type 304 AISI Stainless SteelSCREW HOUSING: Type 304 AISI Stainless SteelSCREW: Type 305 AISI Stainless Steel, 3/8” hex headEYELETS: Series 300 AISI Stainless Steel, fi xed and fl exibleGASKET: Neoprene elastomer

FEATURES3rd Party Listed to ASTM C1540 Standards: • Independently 3rd party listed by IAPMO for compliance to the ASTM C1540 standard for Heavy Duty hubless

couplings (fi le #6199).Engineered Clamp Assembly: • All Stainless Steel clamp assembly features bands riveted to the shield with both fi xed and longer fl exible eyelets.• Super Heavy 3/8” hex head screws with extra long conical head engage smoothly with the clamp bands and

hold the joint in the most challenging installation conditions.• Screw housing interlocks with the band providing a reliable assembly even when screws are torqued up to 125%

of stated installation torque.• Long fl exible eyelet slot allows increased independent movement of the band while tightening which helps

prevent shield crimping and results in a coupling suitable for joining pipe and fi ttings with minimum/maximum tolerance conditions.

Optimum Shield Design: • Through rigorous testing and evaluation, Star engineers have optimized the shield design to provide maximum

joint rigidity, along with the enhanced ability to transfer torque loads to the gasket.• Corrugated pattern bright annealed stainless steel shield effectively transfers compression evenly through the

gasket providing an improved seal and restraint capability.Gasket: • Manufactured from premium virgin Neoprene elastomer resulting in superior performance characteristics

under a wide range of installation conditions.

www.starpipeproducts.com ® REGISTERED TRADEMARK OF STAR PIPE PRODUCTS

STAR® PIPE PRODUCTS - PLUMBING DIVISION4018 West Hollow Parkway � Houston, TX 77082

1-877-909-7827 FAX 866-868-7827

SUPER HEAVY 80 WIDE BODYNOM. ITEM # OF BANDS INSTALLATION

SIZE (IN.) CODE PER COUPLING TORQUE (IN.-LBS.)

11⁄2 NHC0150SHD 4 80

2 NHC0200SHD 4 80

3 NHC0300SHD 4 80

4 NHC0400SHD 4 80

5 NHC0500SHD 6 80

6 NHC0600SHD 6 80

8 NHC0800SHD 6 80

10 NHC1000SHD 6 80

REV:090209-03

APPROVED

SUBMITTAL

STANDARD NO-HUB COUPLING

No-Hub ClassicTM Couplings are engineered

to connect no-hub cast iron pipe in applications

replacing the less-efficient hub & spigot material.

The couplings consists of a high quality

elastomeric compound (ASTM C 564) gasket

housed inside a 301 stainless steel corrugated

shield. Shield is 0.007” thick. Depending on the

size of the shield, two or four 301 stainless steel

clamps encircle the shield and provide the

sealing force. The 5/16” hex-head screws are

305 stainless steel. Available in sizes ranging

from 1-1/2” – 10”. The couplings are designed

for installation torque of 60 in-lbs. The entire

coupling is corrosion resistant. Conforms to

ASTM C1277 and CISPI 310.

Sizes 1-1/2”, 2”, 3”, and 4” consist of a 2-1/8”

wide corrugated 301 stainless steel shield with

two stainless steel clamps mounted in a series

and secured with fixed and floating eyelets to

allow the clamp to travel during tightening.

Sizes 5” and 6” consist of a 3” wide corrugated

301 stainless steel shield with four clamps.

Sizes 8” and 10” consist of a 4” wide

corrugated 301 stainless steel shield with four

stainless steel clamps.

Date:

Project:

Architect:

Contractor: Engineer:

Size Installation

Torque Inch Pounds

No. of Clamps

Per Coupling

1-1\2" 60 2 2" 60 2 3" 60 2 4" 60 2 5" 60 4 6" 60 4 8" 60 4 10" 60 4

2” X 1-1/2” 60 2 3” x 2” 60 2 4” x 3” 60 2

Materials

Band & Housing: Type 301 AISI stainless steel Screw: Type 305 AISI stainless steel,

5/16” hex head Shield: Type 301 AISI stainless steel,

corrugated, thickness 0.007” Gasket: The gasket shall be fabricated

from a high quality elastomeric compound (ASTM C 564).

A product of AIPSA, Matamoros, Mexico Spec No. S1NHC

4/3/07 BB

SUBMITTAL 12” AND 15” HEAVY-DUTY

NO-HUB COUPLINGS _______________________

Date _______________________________

Architect _______________________________

Project _______________________________

Contractor _______________________________

Engineer IDEAL® patented No-Hub Couplings are engineered to connect no-hub cast iron pipe in applications replacing the less-efficient hub & spigot material. The Couplings consists of an elastomeric compound gasket (ASTM C-564) housed inside a 304 stainless steel corrugated shield. Six (6) 304 stainless steel clamps surround the shield and provide the sealing force. The 3/8” hex-head screws are made from 305 stainless steel. The couplings are designed for installation torque of 120 in-lbs. The entire coupling is corrosion resistant.

12” & 15” Heavy-Duty No - Hub Couplings

Size Part No.

Installation Torque Inch

Pounds No. of Clamps Per Coupling

12” 6231M8G 120 6 15" 6232M8G 120 6

The Design The IDEAL® 12” and 15” Heavy-Duty No-Hub Coupling are engineered to provide superior performance at a very competitive cost. Conforms to ASTM C-1277.

The Gasket Made from high-quality elastomeric compound (ASTM C-564), the IDEAL® No-Hub gasket features a pattern of multiple, thick sealing sectors and adjacent groove sectors laterally spaced. When the clamps are tightened, this pattern permits the clamping bands and the shield to form a restriction impeding the movement of the shield relative to the gasket.

The Shield 0.008” thick type 304 stainless steel shield requires less band load to transfer pressure to the gasket, leaving more clamping load in reserve to compress the gasket. The patented, bi-directional corrugations create clamp sealing pressure in both parallel and transverse patterns on the gasket and pipe, thereby avoiding pull-out failures, and providing a positive, reliable seal. In addition, the shield design adjusts to differences in the circumference and outside diameters of the pipes being joined. This eliminates gasket wrinkling and thereby eliminating leak paths. The Clamps Heavy-duty 304 stainless steel clamps and 3/8” hex-head 305 screws provide the sealing force. Both the 12” and the 15” coupling use six (6) 5/8” wide clamps. The entire assembly is corrosion resistant.

4/3/07 BB

12” & 15” NO-HUB COUPLINGS Product Information Submittal for No-Hub Systems

TEST GASKET PHYSICAL TEST MIN. OR MAX. REQUIREMENTS

ASTM METHOD

Tensile Strength

1500 psi min. D 412

Elongation 250 min. D 412 Durometer (Shore A)

70 +/-5 @ 76°F +/- 5°F D 2240

Accelerated Aging

15% maximum tensile and 20% maximum elongation, 10 points maximum increase in hardness, all determinations after oven aging for 96 hours at 158°F

D573

Compression Set

25% max. after 22 hours at 158°F D 395 Method B

Oil Immersion 80% max. volume change after immersion in IRM 903 for 70 hours at 212°F.

D 471

Ozone Cracking

No visible cracking at 2 times magnification of the gasket after 100 hours exposure in 1.5 ppm ozone concentration at 104°F. Testing and inspection to be on gasket which is loop mounted to give approximately 20% elongation of outer surface.

D1149

Tear Resistance

150 lbf /in. min. D 624

Water Absorption

20% max. by weight after 7 days at 158°F D 471

The IDEAL® No-Hub Coupling has been engineered to provide an all stainless steel coupling; balancing the desire for a more rigid joint with the need to provide a superior, positive, reliable seal which can accommodate possible disparities in the mating of No-Hub pipe and fittings. This has been accomplished by manufacturing our coupling with our standard corrugated shield of sufficient width to accommodate additional surface-bearing sealing clamps. The additional sealing clamps, when torqued to 120 in-lbs., deliver additional performance benefits. First, the overall dimensional thickness of the clamp and shield, in conjunction with the additional width of the coupling, result in a more uniformly rigid joint, with the load being supported at both the outer edge of the coupling and the centerline of the joint. Second, the additional sealing clamps yield increased surface-bearing contact between the coupling and the pipe or fittings, thereby inhibiting joint movement at higher internal pressures not commonly associated with DWV systems. The 12” and 15” diameter couplings consist of a 5 1/2” wide bi-directional, corrugated 304 stainless steel shield in conjunction with six (6) stainless steel clamps mounted in a series, secured in place by means of fixed and “floating” eyelets to allow the clamp “travel” during tightening.

MATERIALS Clamp: Type 304 AISI stainless steel Screw: Type 305 AISI stainless steel 3/8” hex head/shoulder Shield: Type 304 AISI stainless steel, corrugated. Shield thickness 0.008” Gasket: The gasket is made of an elastomeric compound that meets the requirements of

ASTM C-564.