EBOX-AP Wireless Repeater EBOX-AP Wireless Repeater

Wireless Repeater

EBOX-AP

Model: EBOX-AP

warranty5 years

Wireless remote

Wireless driver

Wireless driver

DMX driver

Wirelessconnection

Router

Wiredconnection

Wirelessrepeater

Wirelessrepeater

DMX512

RF to DMX

RF 10VPWM to

RF to ELV

RF

RF

DMX512

12-24Vdc

DMX LED driver

0-10V LED driver

Triac LED driver

Mobile phone WiFi gateway

1. System diagram:

1 1 2

10VPWM

ELV

3

2. Technical Specs:

EBOX-AP Wireless Repeater

5~24Vdc

RF 2.4GHz

-30℃~55℃

30m (eye to eye)

Input Voltage:

Wireless Distance:

Wireless Signal:

Working Temp.:

3. Product Size:Unit: mm

50

5521

EBOX-AP wireless repeater applies LT-BUS wireless communication protocol for wireless signal

extension, it is not necessary to pair via its factory default setting, greatly ensures its stability

and wide controlling area among LT-BUS wireless communication devices, removing the

complex cabling procedure, to make it become more easier for new or retrofit installations.

EBOX-AP Wireless Repeater

L55×W55×H21(mm)

L65×W65×H26(mm)

70g

Dimensions:

Package Size:

Weight(G.W.):

4. Terminals:

DC-DC+

Power Input

Match key

www.ltech-led.com 4

C NC match

up with B

C match up with B

C# match up with B#

Receiving end

Receiving end

Receiving end

No need match

Layer 3

Layer 3

Layer N

Layer N

(Max. 8 Layers)

(Max. 8 Layers)

…

…

Interlayer learning method (e.g.: B match up with A)

A repeater between adjacent layers can form a network communication.

Long press the match key of B repeater for about 3 seconds until the internal indicator light flashes, and press A's match key within 10 seconds. At this time, B repeater’s indicator lights keep on after flash 3 times, match successfully. The other layers learn the same way.

N

N#

no s

end

no r

ecei

ve

no s

end

no r

ecei

ve

…

… …

…

…

C

C#

Please set up all controller and receiver before add repeaters

Clear ID code: Long press "match key" for 6s, the indicator light flicker 5 times slowly, clear code successfully.

The repeater leaves the factory by default and can be used without learning, but only single-layer communication (the default is layer 1). For long transmission distance, a multi-level learning (up to 8 layers) is required. For example:

EBOX-AP Wireless Repeater

A BControlling end

Controlling end

B match up with A

B match up with A

B# match up with A#

No need match

No need

match

No need match

Layer 1

Layer 1

Layer 2

Layer 2

5.1 Interlayer diagram

5.2 Stratograms

no s

end

no r

ecei

ve

no s

end

no r

ecei

ve……

A B

B#A#

5. Learning Method:

Wirelessrepeater

Wirelessrepeater

Wirelessrepeater

Wirelessrepeater Wireless

repeaterWireless repeater

Wirelessrepeater

5 6

6. For example

6.1: Panel & repeater application example.

E.g & repeater application example.6.2: WiFi gateway

6.3 Multi-panel control application example.

No need matchNo need match

No need match

No need match

Layer 3

Layer 2

Layer 2 Layer 1Layer 1

Layer 1

Layer 1

Zone control panel

Zone control panel

Zone control panel

Zone control panel Zone control

panel

Zone 1

Zone 1

Zone 2

Zone 3

Zone 4

Zone 2

Zone 3

Zone 4

DMX512

RF

RF

12-24Vdc

Update Time: 2018.04.28_A0www.ltech-led.com

Wireless driver

Wireless driver

Wireless driver

Wireless driver

Wireless driver

Wireless driver

Wireless driver

DMX driver

Strips

Lamps

Lamps

Lamps

Lamps

Need match

Need match

Need match

WiFi gateway

Direct use, No need learning,

EBOX-AP Wireless Repeater EBOX-AP Wireless Repeater