MIZU BLOC BASIN SET

CLEANING RECOMMENDATIONS

To see the complete Mizu range go to www.reece.com.au/bathrooms

SPECIFICATIONSRecommended use Domestic, hotel and commercial.

Colour Chrome

Pressure Rating Maximum continuous operating pressure 1000kPa.

For best performance and longer life we recommend 150-500kPa.

Hot and cold water inlet pressure should be equal.

Temperature Rating Maximum continuous working temperature 80°

Suitable Hot Water Units

Storage Tank: Yes

Continuous Flow: Yes

Gravity Feed: Yes

WELS 4 Star

Flow Rate: 7.5 L/min

Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions are nominal measurements only. Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors.

Tech Page Version 1

We recommend the use of soapy water or approved cleaners.

This product should not be cleaned with abrasive materials.

Damage caused by any improper treatment is not covered by the product warranty- refer to Warranty Conditions.

WaterMarkAS/NZS 3718WMKA 02260

TM

Dimensions are nominal measurements only.

< =1 = > ?@ A ' -

B C14.1 2.30 D C

" # $% &

' ( ) !

* +, (

' -

. /0 1

2 34 5

6 7 8 9 :

!* ; E F

MIZU BLOC BASIN SET

CT4203

CT9505802

16

26

50

50

50

52

52

34

34

140

208

205

88

155@ A '

14.1 2.30 D C

" # $% &

' ( ) !

* +, (

' -

. /0 1

2 34 5

6 7 8 9 :

!* ; E F

16

26

50

50

50

52

52

34

34

140

208

205

88

155

page 1 of 3

The more stars the more water efficient

WATER RATINGwww.waterrating.gov.au

In accordance with AS/NZS 6400

Licence No. 0025Reece Limited

7.5 litres per minute

MIZUBloc BASIN SET

Plumbers, please ensure a copy of the installation instructions is left with the end user for future reference

INSTAllATIoN

Note

Ensure water lines are flushed free of impurities

1. Attach stop bodies (14) to tee-piece (22). Fully tighten connections, but do not overtighten.

2. Insert stop bodies through basin holes ensuring that housing thread extends above basin level

3. Adjust and fix stop bodies (14) into position using locking nuts (10)

4. Separate cartridge locknut and fibre washer (9) from cartridge (12).

5. Grip the cartridge on the hexagonal flats and install cartridge fully into stop body until it comes to a firm stop. Do not tighten cartridge into position by rotating spindle.

6. Turn spindle to off position and turn on water at mains. Check that cartridge has fully seated. If dripping occurs then gentle tighten cartridge further until dripping stops.

7. Firmly tighten cartridge fibre washer (9) and cartridge locknut (7) into position.

8. Place base flange (8) into base of cartridge bonnet (5) and secure down onto cartridge by tightening bonnet by hand.

9. Turn cartridge to fully OFF position.

10. Assemble handle (1) onto spindle and secure in place by fixing with spanner provided.

11. Place locknut (20), and rubber washer (19) onto outlet spigot of tee piece (22).

12. Ensure rubber o-ring is inserted in underside of spout base flange (18)

13. Push outlet through basin top and over o-rings (21) of tee-piece.

14. From underneath, fix outlet into position by tightening locknut (20) onto outlet thread.

O RING

重量数量 比例图 样 标 记

第 张共 张

DR BRASS (ALLOY486)

AERATOR ADAPTOR DR BRASS (ALLOY486)

16x OUTLET

PLASTIC AERATOR

DELRIN 500P NC010

DR BRASS (ALLOY486)INSERTSDR BRASS (ALLOY486)BASIN RECESS BODY

DR BRASS (ALLOY486)

DR BRASS (ALLOY486)

BRASS (ALLOY370)

LOCK NUT

HANDLE

NYLON OLIVE

WASHER EPDM 70

TOP ASSEMBLIES

FIBRE WASHERBASE FLANGENUT

QUADRATE FLANGE BRASS (ALLOY370)

LOCK NUT

LOCK NUT

BRASS (ALLOY370)

BRASS (ALLOY370)

CIRCLIP STAINLESS STEEL

周莲群

签 字

标准化

日 期

审 定

批 准

标记

设 计

处数

校 对

工 艺

更改文件号

日 期审 核 陈 波

描 图

描 校

借通用件登记

旧底图总号

版本

签字

日期

日 期

周莲群

签 字

标准化

审 定

批 准

标记

设 计

处数

校 对

工 艺

更改文件号

日 期审 核

重量数量 比例图 样 标 记

第 张共 张

NO PRODUCT NAME QTY MATERIAL123456789

222222222

MIZU BLOC WALLTOP ASSEMBLIES

WASHER EPDM 70"T" PIECE COPPER

WASHERPLASTIC LOCK NUT ABS

EPDM 70QUADRATE FLANGE

BOLT STAINLESS STEEL

DR BRASS (ALLOY486)

COMPRESSTION NUT DR BRASS (ALLOY486)

210

HANDLE

LOCK NUT

CIRCLIP

LOCK NUT BRASS (ALLOY370)

STAINLESS STEEL

BRASS (ALLOY370)

BRASS (ALLOY370)

QUADRATE FLANGE BRASS (ALLOY370)

BOLT STAINLESS STEEL

NUT

BASE FLANGE BRASS (ALLOY370)

BRASS (ALLOY370)

FIBRE WASHER

CT4100

MIZU BLOC BASIN SET

CT4203

BRASS (ALLOY370)TOP ASSEMBLIES

CT9505802

CT9505803

方管子

Exploded ViewItem Description

1. Handle

2. Lock Nut

3. Circlip

4. Lock Nut

5. Wall Flange

6. Bolt

7. Nut

8. Handle

9. Fibre Washert

10. Lock Nut

11. Washer

12. Top Assemblies

13. Inserts

14. Basin Recess Body

15. Nylon Olive

16. Compression Nut

17. Outlet

18. Wall Flange

19. Washer

20. Lock Nut

21. O Ring

22. T Piece

23. Washer

24. Aerator Adaptor

25. Aerator

page 2 of 3

MIZUBloc BASIN SET

REEcE PRoDUcT QUAlITY GUARANTEEYou have purchased a quality product from Reece Pty Ltd ABN 84 004 097 090 (“Reece”). This product is covered by a 7 year replacement product warranty and a 12 month warranty over spare parts and labour.

7 YEAR WARRANTY – DoMESTIc USEThis warranty covers faults in the product construction, material and assembly. Products which are within 7 years from the date of purchase, found upon inspection by an authorised Reece representative, to be defective in construction, material or assembly, will be repaired or exchanged with an equivalent product free of charge. Replaced items become Reece’s property. This warranty also covers any spare parts included under “Manufacturer’s Provisions” below.

All replacement products will be available for collection without charge to the customer at the nearest Reece branch to the customer’s location, or elsewhere as agreed between the customer and Reece.

Manufacturer’s ProvisionsThe following spare parts are covered by a 7 year warranty:

• Mixer Cartridge

labour and Spare PartsThe labour for the replacement of products and spare parts to which this warranty applies will be supplied by Reece or relevant supplier using licensed plumbers engaged by Reece or relevant supplier within 1 year from the date of purchase.

Spare parts other than those listed in the Manufacturer’s Provisions above, which are within 1 year from the date of purchase found upon inspection by an authorised Reece representative to be defective in construction, material or assembly, will be replaced free of charge.

Warranty conditionsThis warranty will apply only under all of the following conditions:

• The item has been installed by a licensed plumber

• The item has been installed for and subjected to domestic residential use only

• Failure is due to a fault in the manufacture of the product

• Proof of purchase (including the date of purchase) is provided

• The installation of the product is in accordance with the instructions provided

This warranty does not cover products purchased as an ex-display without being fully checked and tested for sale by the manufacturer.

This warranty does not include faults caused by:

• Unsuitable or improper use

• Incorrect installation or installation not in accordance with the instructions provided

• Installation or part installation by the purchaser or any person other than a LICENSED PLUMBER

• Normal wear and tear

• Inadequate or complete lack of maintenance

• Chemical, electrochemical or electrical influences

• Harsh detergents or abrasive cleaners used on product finishes

1 YEAR WARRANTY – coMMERcIAl USE‘Commercial’ use is all use other than for normal domestic residential purposes, including use in non-business places as in public buildings, schools, sports centres and in establishments that contain private bathrooms with high frequency of use by many individuals, such as hotels, motels, retirement villages and hospitals.

The Commercial warranty covers this product against manufacturing faults in the construction, material and assembly of both the finished products and any spare parts for a period of 1 year from the date of purchase. Products and spare parts which are found upon inspection by an authorised Reece representative to be defective in construction, material or assembly will be repaired or exchanged free of charge. Replaced items become Reece’s property. The labour for the replacement of products and spare parts to which this warranty applies will be supplied by Reece or relevant supplier using licensed plumbers engaged by Reece or relevant supplier. The Warranty Conditions and exclusions which apply to the domestic use warranty also apply to this commercial warranty.

EXclUSIoNSTo the fullest extent permitted by law, Reece excludes all liability for damage or injury to any person, damage to any property, and any indirect consequential or other loss or damage.

clAIM PRocEDUREFor all warranty queries customers are to contact the branch where the product was purchased. These details can be found on your purchase invoice.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

TAP.

T1.7

YR

Don’t risk it, use a licensed plumber.™

7YEARQ

U

ALITY GUARANTEE

Cartridges

page 3 of 3