www.rfsworld.com516

6

BR

OA

DC

AST

AN

TEN

NA

SYST

EMS

YLV Series

The YLV3 yagi antenna is suitable for use as anelement in VHF transmitting arrays. By arranging anumber of these elements around a suitable tower ormast an omnidirectional or a number of directionalradiation patterns can be achieved. The YLV3 can alsobe used as a stand alone antenna.

• Suitable for use as an array element or for standalone operation

• Engineered for transmission of both Digital andAnalog TV/Radio

• Light weight and low wind

• All elements are DC grounded for lightningprotection

The antenna can be center mounted for singleantenna applications or by an extended boom formounting to tower or mast in an array configuration.Bracing kits are supplied as standard with antennasthat require them. Mounting hardware is stainlesssteel. To facilitate package and transport, yagiantennas are transported as components. Detailedassembly instructions are provided. Mounting clampsand tower brackets are available to suit a range oftower types. Contact RFS with your requirements.

YLV3 - Dimensions shown for the modelcovering 47 - 54 MHz

47 - 108 MHz

2547

mm

1830mm

DRAIN HOLE

INPUT 'N' TYPE

Y203 Yagi Antenna

Band I and II (VHF) Yagi Antennas

www.rfsworld.com517

BR

OA

DC

AST

AN

TENN

ASY

STEMS

6

YLV Series

Band I and II (VHF) Yagi Antennas 47 - 108 MHz

0.8

0.6

0.4

0.2

180

0

270 90

E / Emax

Azimuth Radiation PatternSingle Antenna

0.8

0.6

0.4

0.2

180

0

270 90

E / Emax

Azimuth Radiation Pattern4-Antenna array

RADIATION PATTERN - Typical Azimuth Singleantenna

RADIATION PATTERN - Typical Azimuth Array offour antennas on square mast

SPECIFICATIONS YLV3Frequency Range, MHz 47 - 108Polarization HorizontalNumber of Channels Single channel up to 8 MHzNominal Gain (Mid-band), dBd 4.2Return Loss, dB >21 (typically 26 across channel)Input Connector N typePower Rating per Input, kW 0.5Impedance, ohms 50 unbalancedOperating Temperature Range, degrees C -10 to +50Weight, kg (lb) 17 (37)Dimensions (Height or Length), cm (in) 20Dimensions (Width), cm (in) 325.4Dimensions (Depth), cm (in) 222.0Effective Area Front (full antenna), sq m (sq ft) 0.46 (4.95)Effective Area Side (full antenna), sq m (sq ft) 0.13 (1.4)Design Wind Speed (max), km/h (mph) 240 (150)Wind Load @ 50 m/sec Front, kN (lb) 0.69 (155)Wind Load @ 50 m/sec Side, kN (lb) 0.2 (45)Material - Support Pole / Mounting Stainless SteelMaterial - Radiators 6000 Series aluminum alloy

www.rfsworld.com551

BR

OA

DC

AST

AN

TENN

ASY

STEMS

6

PHP10S Series

Band V (UHF) TV Panel Arrays

The PHP10S broadband panel is designed as abuilding block for integration into complex antennaarrays or can be used individually for simple antennasystems. This panel covers upper Band V frequencyrange without field adjustment.

• Engineered for digital or analogue TV

• Corrosion resistant aluminum construction withluran radome

• Horizontal polarization

• Low wind loading

• Cyclone rated

• High power rating

• Array design allows a variety of horizontalradiation patterns with or without beam tilt andnull fill, contact RFS for details

Standard antennas are pressurizable and have a 7/8”EIA input connector. A capacitive probe is supplied atthe input. Panels can also be supplied with dual 7/8”EIA connectors to achieve 4.4kW power rating. 7-16DIN and N type input connectors are also availablefor low power situations without the capacitive probe.Radomes for individual panels are supplied in whiteluran as standard. Also available in orange.

Array design can provide any of an almost infinitevariety of horizontal patterns, with or without verticalbeam tilt and null fill. Omnidirectional radiationcharacteristics can be achieved by mounting anynumber of panels around a suitably sized supportingstructure. Horizontal radiation patterns for four panelsaround a 400 mm square. These are plotted for750MHz, 800MHz and 860MHz. Panels can also bemounted 10 around on an 800mm square column.

PHP10S Panel

750 - 870 MHz

PHP10S Panel

www.rfsworld.com552

6

BR

OA

DC

AST

AN

TEN

NA

SYST

EMS

PHP10S Series

Band V (UHF) TV Panel Arrays 750 - 870 MHz

0

E/Emax

180

0.8

0.6

0.4

0.2

270 90

HorizontalVertical

Radiation Pattern Radiation Pattern - 4 panels on 400 mm column(750MHz, 800MHz, 860MHz)

SPECIFICATIONS (ALL MODELS)Frequency Range, MHz 750 - 870Polarization HorizontalNumber of Channels MultichannelNominal Gain (Mid-band), dBd 11Half Power Beamwidth Azimuth, degrees 60Return Loss, dB > 26Impedance, ohms 50Mounting (Standard), mm (in) 4 x 10mm (3/8”) boltsEffective Area Front (full antenna), sq m (sq ft) 0.24 (2.58)Effective Area Side (full antenna), sq m (sq ft) 0.16 (1.72)Design Wind Speed (max), km/h (mph) 240 (150)Pressurization Operational, kPa (psi) 10 - 35 (1.5 - 5) Note#2Pressurization Test, kPa (psi) 100 (15)Material - Radome LuranMaterial - Insulators PTFEMaterial - Radiators Corrosion resistant aluminumMaterial - Reflecting Screen Corrosion resistant aluminum

SPECIFICATIONS PHP10SN PHP10S4 PHP10SInput Connector N socket 7-16 DIN 7/8” EIAPower Rating, kW 0.25 1.4 Note#1 2.2 Note#1Weight, kg (lb) 3.7 (8) 3.7 (8) 5.5 (12)

Note 1Double power version available with dual 7/8” EIA inputs.Note 27/8” EIA version only.

1.2 m | 4 ft Standard Parabolic Unshielded Antenna, single­polarized, 5.725–6.425 GHz P4-57W

CHARACTERISTICS

General Specif ications Antenna Type P ­ Standard Parabolic Unshielded Antenna, single­polarized

Diameter, nominal 1.2 m | 4 ft

Polarization Single

Electrical Specifications Beamwidth, Horizontal 2.9 °

Beamwidth, Vertical 2.9 °

Cross Polarization Discrimination (XPD) 30 dB

Front­to­Back Ratio 40 dB

Gain, Low Band 34.6 dBi

Gain, Mid Band 35.0 dBi

Gain, Top Band 35.4 dBi

Operating Frequency Band 5.725 – 6.425 GHz

Radiation Pattern Envelope Reference (RPE) 4268

Return Loss 26.4 dB

VSWR 1.10

Mechanical Specif ications Fine Azimuth Adjustment ±5°

Fine Elevation Adjustment ±5°

Mounting Pipe Diameter 115 mm | 4.5 in

Net Weight 47 kg | 104 lb

Side Struts, Included 1 inboard

Side Struts, Optional 1 inboard

Product Specifications

©2011 CommScope, Inc. All rights reserved.All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope.All specifications are subject to change. See www.commscope.com/andrew for the most current information.

page 1 of 54/1/2011

2.4 m | 8 ft High Performance Parabolic Shielded Antenna, single­polarized, 5.725–6.425 GHz HP8-57W

CHARACTERISTICS

General Specif ications Antenna Type HP ­ High Performance Parabolic Shielded Antenna, single­polarized

Diameter, nominal 2.4 m | 8 ft

Polarization Single

Electrical Specifications Beamwidth, Horizontal 1.6 °

Beamwidth, Vertical 1.6 °

Cross Polarization Discrimination (XPD) 30 dB

Electrical Compliance ETSI Class 2 | US FCC Part 101A

Front­to­Back Ratio 64 dB

Gain, Low Band 40.7 dBi

Gain, Mid Band 41.2 dBi

Gain, Top Band 41.7 dBi

Operating Frequency Band 5.725 – 6.425 GHz

Radiation Pattern Envelope Reference (RPE) 4273

Return Loss 30.7 dB

VSWR 1.06

Mechanical Specif ications Fine Azimuth Adjustment ±5°

Fine Elevation Adjustment ±5°

Mounting Pipe Diameter 115 mm | 4.5 in

Net Weight 227 kg | 500 lb

Side Struts, Included 1 inboard | 1 outboard

Product Specifications

©2011 CommScope, Inc. All rights reserved.All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope.All specifications are subject to change. See www.commscope.com/andrew for the most current information.

page 1 of 54/1/2011

18

K 52 16 8. .Directional Antenna47 ... 88 MHz

Type No. K 52 16 81 7 K 52 16 82 7 K 52 16 83 7 K 52 16 84 7 K 52 16 85 7 K 52 16 86 7Order No. 600 223 600 225 600 227 601 822 601 823 601 824

Frequency range

Channel

InputVSWRGain (ref. λ/2 dipole)PolarizationImpedanceMax. powerDimensions in mm A

BC

Weight in kgWind load in N (at v = 160 km/h)Horizontally polarized frontal

lateralVertically polarized frontal

lateralPacking in cm Max. wind velocity

47 – 54 MHz 54 – 61 MHz 60 – 68 MHz 66 – 72 MHz 76 – 82 MHz 82 – 88 MHz2 3 4

2 3 4 5 67-16 female

< 1.156 dB

Horizontal or vertical by conversion of the clamps50 Ω

200 W (higher power upon request)3500 2950 2700 2420 2120 19703000 2510 2240 2070 1810 16802225 1950 1740 1610 1410 131018 15 12.5 11.5 10 9

715 615 540 500 440 400675 575 475 440 375 350715 615 540 500 440 400790 675 615 565 500 465

330 x 76 x 13 275 x 76 x 13 250 x 76 x 13 222 x 76 x 13 192 x 76 x13 177 x 76 x 13

160 km/h

Material: Support: Weather-proof aluminum. Elements: Fiberglass with inlaid copper wire.Cover: Fiberglass. Clamp: Hot-dip galvanized steel.

Mounting: To pipes of 60 – 115 mm diameter by means of mounting clamps, supplied.

Special features: The antenna is shipped dismounted.

Combinations: Two or more antennas can be combined to achieve higher gain and longer, narrowerbeam width.

Grounding: Via mounting parts.

8 element Yagi-antenna of weather-proof aluminum, fiberglass-elementswith encapsulated copper stranded wire.

3 dB

10

0

68°

3 dB

10

0

128°

in E-planeHorizontal Radiation Pattern

in H-planeVertical Radiation Pattern

Radiation Patterns(at mid-band)

C

B

A

Length see table

Roof mount antenna 62 ... 300 MHz / Car radio AM/FM

Type No. K 50 53 4 With spring, 62 ... 300 MHz,Ord. No. 510 314 0 dB gain (ref. to quarter-wave

whip),supply length 1285 mm

Connection Fixed cable RG 058-PE, 5 meters long, without radio set connector.

Maximum load 100 W(at 50 °C ambient temperature)

Tuning By shortening the whip (please note mounting instructions).

Mounting In bore hole (24 mm diameter) from the external side of the car body.

Built-in depth 14 mm

Max. diameter at base 38 mm

Material Whip and spring: Stainless steel.Swivel-joint parts: Chromium-plated brass. Base: Weather resistant plastic.

Contents of delivery Whip, base with cable, philips screw.

Accessories For AM/FM reception (VHF) the coupler K 62 27 4 (Ord. No. 510 431) is required.

Components Type No. (Ord. No.)Whip K 50 47 40 41 (510 300)Base K 50 55 20 31 (510 142)Swivel-joint screw* K 66 00 6 (510 154)Tip protection K 66 01 9 (510 159)

* butterfly bolt + philips screw + locking washer

20

K 50 53 4

20

FM Transmitting Antennawith dipole panels 754 15487.5 – 108 MHz

Antenna array of circularly polarized dipole panels 754 154 for different radiation patterns,especially suitable for mounting on triangular or round masts.

The feeder network is made up of coaxial power splitters and flexible connecting cables in accordance with the radiation patterns specification and the transmitting power.

Input Connectors according to IEC, EIA or DIN.Frequency range 87.5 – 108 MHzVSWR s < 1.2 throughout the whole frequency range.

Lower VSWR for single channels upon request.Impedance 50 ΩPolarization CircularInternal connections Connectors according to IEC, EIA or DIN

are used throughout the system,allowing easy assembly and maintenance.

Max. power According to customer’s requirements.Vertical radiation pattern Null fill and beam tilt upon request.Horizontal radiation pattern Omnidirectional, directional or custom-designed.Half antenna splitting Upon request, the antenna can be divided into

2 halves (for measurement and maintenance).The 2 halves are connected by a

2-way power splitter or patch panel.Pressurization Splitters and connecting cables can be supplied

with dry air (please specify when ordering).Painting If required, the antenna is painted in aviation

warning colours.Grounding Via mounting parts.Max. wind velocity 225 km/h

H

3000

mm

No. Panels Gain* Weight Antenna Windloadof per (at mid-band) (without mounting height H (v = 160 km/h)

bays bay dB times hardware) kg m kN

2 0.0 1.0 140 2.31 3 –2.0 0.6 200 1.82 3.2

2 3.1 2.0 260 4.62 3 1.1 1.3 430 4.82 6.3

2 6.2 4.2 580 9.24 3 4.2 2.6 800 10.82 12.6

2 8.1 6.5 800 13.86 3 6.1 4.1 1230 16.82 18.9

2 9.3 8.5 1100 18.48 3 7.3 5.4 1590 22.82 25.2

* Referred to λ/2 dipole. Attenuation of the internal cabling and the gain-decreasein case of null fill in the vertical radiation pattern are not considered.Approximate values for gain decrease:

cable attenuation: 0.2 – 0.5 dBnull fill: 0.3 – 1.0 dB

Gain figures are valid for the direction of maximum radiation (see diagrams onfollowing page).

21

FM Transmitting Antennawith dipole panels 754 15487.5 – 108 MHz

3 dB

10

0

60°

3 dB

10

0

60°

3 dB

10

0

3 dB

10

0

1,0

0,5

0 10 20 α°

E rel

30 40

1,0

0,5

0 10 20 α°

E rel

30 40

1,0

0,5

0 10 20 α°

E rel

30 40

1,0

0,5

0 10 20 α°

E rel

30 40

2 bays

4 bays

6 bays

8 bays

3/4P

1/4P

3/7P

1/7P

3/7P

Horizontal Radiation Patterns

Examples of typical horizontalantenna arrays and their horizontal radiation patterns

for minimal mast dimensions.

Vertical Radiation Patterns

Examples of typical verticalradiation patterns*) for several bays

of identical, vertically stacked antenna arrays.

*) without null fillwith null fill and beam tilt

Equal power splitting

Different power splitting

www.rfsworld.com121

BA

SE STATIO

NA

NTEN

NA

S

2

Polarization: Dual ± 45°Electrical Downtilt: AdjustableHorizontal beamwidth: 65° or 90°

20 m

Horizon10˚ 8˚

2.0˚5˚

110 m

138 m

220 m550 m

90

60120

30

0

-30

-60-120

-90

10 32030 10 32030

V e r t i c a l P a t t e r n

90

60120

30

0

-30

-60-120

-90

10 32030 10 32030

H o r i z o n t a l P a t t e r n

• Constant performance across frequency band forall tilt values

• At least 30 dB isolation between polarization’s

• High gain

• Stable horizontal and vertical beamwidths

• Excellent upper sidelobe suppression

• Very low beam squint

• Effective polarization diversity ensured by highcross polar discrimination

• Broadband design

• Low wind load

• Optional remote tilt – can be retrofitted

ApplicationsThis innovative range of broadband variable tilt antennas are cross-polarized available in 65° or 90 degree horizontal beamwidths foruse in the following systems:

Trunking / SMR (806-824, 851-869MHz)Cellular (824-849, 869-896 MHz)GSM 900 / ETACS (872-915, 917-960MHz)Trunking (896-901, 935-940MHz)

These high performance antennas have excellent upper sidelobesuppression, VSWR and front to back ratio. The antennas areavailable in a variety of gain options varying from 15.2 to 18.2dBicovered by an UV resistant fiberglass radome. Having continuouslyadjustable electrical downtilt over the range of 0° to 10°. Theseantennas have two 7-16 connectors mounted at the bottom and aredesigned for use with our new APM40 Global Mount system /APM70-3C cluster kit.

As with all our variable tilt antenna range they can be upgradedusing our OPTIMIZER RT® system for remote tilt control.

Features & Benefits APXV86-90* Series

APXV86-90* Series 806-960 MHz

Optimizer® Broadband AntennasBroadband Tilt range 10°

Fighting co-channel interferences is key to improving networkperformances. A tight control of the coverage by adjusting downtiltto the optimum value helps reducing co-channel interferences.

Effect of adjustable antenna downtilt on tight coverage control

Performance Optimization Techniques

www.rfsworld.com122

2

BA

SE S

TATI

ON

AN

TEN

NA

S

APXV86-90* Series 806-960 MHz

Optimizer® Broadband AntennasAPXV86-906513L-CHorizontal Beamwidth, deg 65Gain, dBi 14.7Electrical Downtilt, deg 0-10

Vertical Pattern

Horizontal Pattern

ELECTRICAL SPECIFICATIONSFrequency Range, MHz 806-870 870-960Horizontal Beamwidth, deg 67 63Vertical Beamwidth, deg 16 15Gain, dBi (dBd) 14.4 (12.3) 15 (12.9)1st Upper Sidelobe Suppression, dB > 18 > 18Front-To-Back Ratio, dB > 25VSWR < 1.5:1 < 1.4:1Isolation between Ports, dB > 30Maximum Power Input, W 500Polarization Dual pol +/-45°3rd Order IMP @ 2 x 43 dBm, dBc > 150MECHANICAL SPECIFICATIONSDimensions - HxWxD, mm (in) 1350 x 330 x 130 (53.15 x 13 x 5.12)Survival Wind Speed, km/h (mph) 200 (125)Max Wind Loading Area, m² (ft²) 0.45 (4.81)Rated Wind Speed, km/h (mph) 160 (100)Maximum Thrust @ Rated Wind, N (lbf) 685 (154)Front Thrust @ Rated Wind, N (lbf) 685 (154)Reflector Material AluminumRadiating Element Material BrassRadome Material FiberglassRadome Color Light Grey RAL7035Weight w/o Mtg Hardware, kg (lb) 14 (30.8)Packing Dimensions - HxWxD, m (ft) 1.5 x 0.4 x 0.25 (4.95 x 1.32 x 0.83)Packing Dimensions, HxWxD, mm (in) 1520 x 400 x 250 (59.84 x 15.75 x 9.84)

APXV86-906513T-CHorizontal Beamwidth, deg 65Gain, dBi 14.7Electrical Downtilt, deg 4-14

Vertical Pattern

Horizontal Pattern

ELECTRICAL SPECIFICATIONSFrequency Range, MHz 806-870 870-960Horizontal Beamwidth, deg 67 63Vertical Beamwidth, deg 16 15Gain, dBi (dBd) 14.4 (12.3) 14.8 (12.7)1st Upper Sidelobe Suppression, dB > 16 > 18Front-To-Back Ratio, dB > 25VSWR < 1.3:1Isolation between Ports, dB > 30Maximum Power Input, W 500Polarization Dual pol +/-45°3rd Order IMP @ 2 x 43 dBm, dBc > 150MECHANICAL SPECIFICATIONSDimensions - HxWxD, mm (in) 1350 x 330 x 130 (53.15 x 13 x 5.12)Survival Wind Speed, km/h (mph) 200 (125)Max Wind Loading Area, m² (ft²) 0.45 (4.81)Rated Wind Speed, km/h (mph) 160 (100)Maximum Thrust @ Rated Wind, N (lbf) 685 (154)Front Thrust @ Rated Wind, N (lbf) 685 (154)Reflector Material AluminumRadiating Element Material BrassRadome Material FiberglassRadome Color Light Grey RAL7035Weight w/o Mtg Hardware, kg (lb) 14 (30.8)Packing Dimensions - HxWxD, m (ft) 1.5 x 0.4 x 0.25 (4.95 x 1.32 x 0.83)Packing Dimensions, HxWxD, mm (in) 1520 x 400 x 250 (59.84 x 15.75 x 9.84)

www.rfsworld.com301

MIC

RO

WA

VE

AN

TENN

ASY

STEMS

4

SlimLine Ultra High Performance, Dual PolarizedSUX4-107A 4 (1.2) 1.5 40 40.4 40.8 66 32 35 1.20 / 20.8 ± 5 ± 10 200 (125) 35 (77) A Range 1, class 3SUX6-107B 6 (1.8) 1 43.6 43.9 44.4 70 32 35 1.20 / 20.8 ± 5 ± 5 200 (125) 95 (209) A Range 1, class 3CompactLine, Single PolarizedSB2-107C 2 (0.6) 3.0 34.8 35.1 35.4 60 30 1.30 / 17.7 ± 30 ± 30 250 (156) 12 (26.5) B Range 1, class 3SB2-107B 2 (0.6) 3.0 34.8 35.1 35.4 60 30 1.30 / 17.7 ± 5 ± 10 250 (156) 12 (26.5) B Range 1, class 3SB4-107B 4 (1.2) 1.5 40.0 40.4 40.8 67 30 1.30 / 17.7 ± 5 ± 10 200 (125) 35 (77) A Range 1, class 3SB3-107A 3 (0.9) 2 37.9 38.4 38.8 64 30 1.30 / 17.7 ± 5 ± 15 200 (125) 23 (50.5) B Range 1, class 3

Parabolic Point to Point Antennas 10.7 - 11.7 GHz

Antenna Input1 – 154 IEC-PDR 100, 154 IEC-PBR 100, CPR90G, UG40B/UModel Diameter 3 dB-BW Gain (dBi) F/B Ratio XPD IPI VSWR/ Fine Adjustment Windspeed Weight FCC ETSINumber ft (m) (deg) Low Mid High (dB) (dB) (dB) R L (dB) Az (deg) Elev (deg) km/h (mph) kg (lb) Standard Standard

1To specify antenna input at the time of order, insert the appropriate antenna input code, from page 281, after the revision letter in the modelnumber.

12.2 - 13.25 GHzAntenna Input1 – 154 IEC-PDR 120, WR75 CHOKEModel Diameter 3 dB-BW Gain (dBi) F/B Ratio XPD IPI VSWR/ Fine Adjustment Windspeed Weight FCC ETSINumber ft (m) (deg) Low Mid High (dB) (dB) (dB) R L (dB) Az (deg) Elev (deg) km/h (mph) kg (lb) Standard StandardStandard Performance, Low VSWR, Single PolarizedPAL2-122B 2 (0.6) 2.7 35.2 35.5 35.8 42 30 1.13 / 24.3 ± 30 ± 30 250 (156) 10 (22) Range 1, class 1PAL4-122A 4 (1.2) 1.4 41.3 41.6 41.9 48 30 1.10 / 26.4 ± 5 ± 10 200 (125) 30 (66) B Range 1, class 1PAL6-122B 6 (1.8) 0.9 44.8 45.2 45.5 52 30 1.08 / 28.3 ± 5 ± 5 200 (125) 50 (110) A Range 1, class 1PAL8-122A 8 (2.4) 0.7 47.3 47.6 47.9 54 30 1.08 / 28.3 ± 5 ± 5 200 (125) 120 (264) A Range 1, class 1PAL10-122A 10 (3.0) 0.6 49 49.4 49.7 57 30 1.08 / 28.3 ± 5 ± 5 200 (125) 215 (473) A Range 1, class 1Standard Performance, Dual PolarizedPAX6-122B 6 (1.8) 0.9 44.6 45 45.3 52 30 35 1.10 / 26.4 ± 5 ± 5 200 (125) 50 (110) A Range 1, class 1PAX8-122A 8 (2.4) 0.7 47.1 47.4 47.7 54 30 35 1.10 / 26.4 ± 5 ± 5 200 (125) 120 (264) A Range 1, class 1PAX10-122A 10 (3.0) 0.6 48.8 49.2 49.5 57 30 35 1.10 / 26.4 ± 5 ± 5 200 (125) 215 (473) A Range 1, class 1High Performance, Single PolarizedDA2-122B 2 (0.6) 2.7 35.2 35.5 35.8 56 30 1.13 / 24.3 ± 30 ± 30 250 (156) 15 (33) Range 1, class 2DA4-122A 4 (1.2) 1.4 41.3 41.6 41.9 62 30 1.10 / 26.4 ± 5 ± 10 200 (125) 35 (77) B Range 1, class 2DA6-122B 6 (1.8) 0.9 44.8 45.2 45.5 67 30 1.08 / 28.3 ± 5 ± 5 200 (125) 95 (209) A Range 1, class 2DA8-122A 8 (2.4) 0.7 47.3 47.6 47.9 70 30 1.08 / 28.3 ± 5 ± 5 200 (125) 180 (396) A Range 1, class 2DA10-122A 10 (3.0) 0.6 49 49.4 49.7 71 30 1.08 / 28.3 ± 5 ± 5 200 (125) 290 (638) A Range 1, class 2High Performance, Dual PolarizedDAX2-122B 2 (0.6) 2.7 34.9 35.2 35.5 56 30 35 1.15 / 23.1 ± 30 ± 30 250 (156) 15 (33) Range 1, class 2DAX4-122A 4 (1.2) 1.4 41 41.3 41.6 62 30 35 1.10 / 26.4 ± 5 ± 10 200 (125) 35 (77) B Range 1, class 2DAX6-122B 6 (1.8) 0.9 44.6 45 45.3 67 30 35 1.10 / 26.4 ± 5 ± 5 200 (125) 95 (209) A Range 1, class 2DAX8-122A 8 (2.4) 0.7 47.1 47.4 47.7 70 30 35 1.10 / 26.4 ± 5 ± 5 200 (125) 180 (396) A Range 1, class 2DAX10-122A 10 (3.0) 0.6 48.8 49.2 49.5 71 30 35 1.10 / 26.4 ± 5 ± 5 200 (125) 290 (638) A Range 1, class 2

www.rfsworld.com288

4

MIC

RO

WA

VE

AN

TEN

NA

SYST

EMS

Parabolic Point to Point Antennas 2.3 - 2.5 GHz

Antenna Input1 – N Male

1To specify antenna input at the time of order, insert the appropriate antenna input code, from page 281, after the revision letter in the modelnumber.

3.6 - 4.2 GHzAntenna Input1 – 154 IEC-PDR 40

Model Diameter 3 dB-BW Gain (dBi) F/B Ratio XPD IPI VSWR/ Fine Adjustment Windspeed Weight FCC ETSINumber ft (m) (deg) Low Mid High (dB) (dB) (dB) R L (dB) Az (deg) Elev (deg) km/h (mph) kg (lb) Standard StandardSlimLine Standard Performance, Non-Pressurized, Single PolarizedSPF2-23A 2 (0.6) 13.8 20.1 20.5 20.9 30 25 1.50/13.98 ± 5 ± 15 200 (125) 10 (22) –SPF3-23A 3 (0.9) 9.2 23.8 24.2 24.5 33 25 1.50/13.98 ± 5 ± 15 200 (125) 16 (35.2) –SPF4-23A 4 (1.2) 6.9 26.7 27.1 27.4 36 25 1.50/13.98 ± 5 ± 10 200 (125) 24 (52.8) –SPF6-23B 6 (1.8) 4.6 30.2 30.6 31.0 39 25 1.50/13.98 ± 5 ± 5 200 (125) 50 (110) –

Model Diameter 3 dB-BW Gain (dBi) F/B Ratio XPD IPI VSWR/ Fine Adjustment Windspeed Weight FCC ETSINumber ft (m) (deg) Low Mid High (dB) (dB) (dB) R L (dB) Az (deg) Elev (deg) km/h (mph) kg (lb) Standard StandardStandard Performance, Low VSWR, Single PolarizedPAL6-36B 6 (1.8) 3 34.3 34.8 35.5 42 30 1.08 / 28.3 ± 5 ± 5 200 (125) 50 (110) * Range 1, class 1PAL8-36A 8 (2.4) 2.3 36.6 37.3 37.9 44 30 1.06 / 30.7 ± 5 ± 5 200 (125) 120 (264) Range 1, class 1PAL10-36A 10 (3.0) 1.8 38.5 39.2 39.8 47 30 1.06 / 30.7 ± 5 ± 5 200 (125) 215 (473) B Range 1, class 1PAL12-36A 12 (3.7) 1.5 40.1 40.8 41.4 50 30 1.06 / 30.7 ± 5 ± 5 200 (125) 310 (682) B Range 1, class 1PAL15-36A 15 (4.6) 1.1 42 42.7 43.3 52 30 1.06 / 30.7 ± 5 ± 5 200 (125) 570 (1254) B Range 1, class 1Standard Performance, Dual PolarizedPAX6-36B 6 (1.8) 3 34.2 34.7 35.4 42 30 35 1.08 / 28.3 ± 5 ± 5 200 (125) 50 (110) * Range 1, class 1PAX8-36A 8 (2.4) 2.3 36.5 37.2 37.8 44 30 35 1.06 / 30.7 ± 5 ± 5 200 (125) 120 (264) Range 1, class 1PAX10-36A 10 (3.0) 1.8 38.4 39.1 39.7 46 30 35 1.06 / 30.7 ± 5 ± 5 200 (125) 215 (473) Range 1, class 1PAX12-36A 12 (3.7) 1.5 40 40.7 41.3 49 30 35 1.06 / 30.7 ± 5 ± 5 200 (125) 310 (682) B Range 1, class 1PAX15-36A 15 (4.6) 1.1 42 42.7 43.3 52 30 35 1.06 / 30.7 ± 5 ± 5 200 (125) 570 (1254) B Range 1, class 1High Performance, Single PolarizedDA6-36B 6 (1.8) 3 33.7 34.4 35 56 30 1.08 / 28.3 ± 5 ± 5 200 (125) 95 (209) * Range 1, class 2DA8-36A 8 (2.4) 2.3 36.5 37.2 37.8 60 30 1.06 / 30.7 ± 5 ± 5 200 (125) 180 (396) Range 1, class 2DA10-36A 10 (3.0) 1.8 38.4 39.1 39.7 62 30 1.06 / 30.7 ± 5 ± 5 200 (125) 290 (638) Range 1, class 2DA12-36A 12 (3.7) 1.5 40 40.7 41.3 63 30 1.06 / 30.7 ± 5 ± 5 200 (125) 420 (924) B Range 1, class 2DA15-36A 15 (4.6) 1.1 42 42.7 43.3 65 30 1.06 / 30.7 ± 5 ± 5 200 (125) 750 (1650) B Range 1, class 2High Performance, Dual PolarizedDAX8-36A 8 (2.4) 2.3 36.5 37.2 37.8 60 30 35 1.08 / 28.3 ± 5 ± 5 200 (125) 180 (396) Range 1, class 2DAX10-36A 10 (3.0) 1.8 38.4 39.1 39.7 62 30 35 1.06 / 30.7 ± 5 ± 5 200 (125) 290 (638) Range 1, class 2DAX12-36A 12 (3.7) 1.5 40 40.7 41.3 63 30 35 1.06 / 30.7 ± 5 ± 5 200 (125) 420 (924) B Range 1, class 2DAX15-36A 15 (4.6) 1.1 42 42.7 43.3 65 30 35 1.06 / 30.7 ± 5 ± 5 200 (125) 750 (1650) B Range 1, class 2Ultra High Performance, Single PolarizedUA6-36B 6 (1.8) 3 33.7 34.4 35 60 30 1.08 / 28.3 ± 5 ± 5 200 (125) 95 (209) * Range 1, class 3UA8-36A 8 (2.4) 2.3 36.5 37.2 37.8 64 30 1.06 / 30.7 ± 5 ± 5 200 (125) 180 (396) Range 1, class 3UA10-36A 10 (3.0) 1.8 38.4 39.1 39.7 66 30 1.06 / 30.7 ± 5 ± 5 200 (125) 290 (638) B Range 1, class 3UA12-36A 12 (3.7) 1.5 40 40.7 41.3 68 30 1.06 / 30.7 ± 5 ± 5 200 (125) 420 (924) B Range 1, class 3Ultra High Performance, Dual PolarizedUDA6-36B 6 (1.8) 3 33.5 34.2 34.8 60 30 35 1.08 / 28.3 ± 5 ± 5 200 (125) 95 (209) * Range 1, class 3Ultra High Performance, High Crosspolar Discrimination, Dual PolarizedUXA8-36A 8 (2.4) 2.3 36.5 37.2 37.8 66 40 45 1.08 / 28.3 ± 5 ± 5 200 (125) 180 (396) Range 1, class 3, XPDUXA10-36A 10 (3.0) 1.8 38.4 39.1 39.7 67 40 45 1.06 / 30.7 ± 5 ± 5 200 (125) 290 (638) B Range 1, class 3, XPDUXA12-36A 12 (3.7) 1.5 40 40.7 41.3 70 40 45 1.06 / 30.7 ± 5 ± 5 200 (125) 420 (924) A Range 1, class 3, XPDUXA15-36A 15 (4.6) 1.1 42 42.7 43.3 72 38 45 1.06 / 30.7 ± 5 ± 5 200 (125) 750 (1650) B Range 1, class 3, XPD

info@antenas.comCap. M. Cajaraville 3629 - Carapachay - Argentina 766-4510/3916 - 763-1245 /1345 - 54(1)11-2593& :

DESCRIPCION DEL PRODUCTO

La yagi soldada D7E-150BAS , es una an-tena direccional de 7 elementos, de banda ancha, enla banda de 120 a 200 MHz.. La misma se entregamedida en forma individual , en lo que se refiere aR.O.E., desde antes de la frecuencia mínima y hastamás allá de la máxima especificada.

No necesita de ningún ajuste en el lugar deinstalación y se provee con todas sus grampas desujeción.

DESCRIPCION ELECTRICA

La conexión del balun y la linea de transmisiónal elemento radiador está realizada con una "UNIONMOLECULAR INTERMETALICA LAMINADA" UMIL.Esta unión garantiza la ausencia total de corrosión enlos lugares donde deben unirse la linea de transmisióny el balun (cobre) con la aleación de aluminio delelemento excitado. El resultado de esta técnica evitatotalmente la reducción de la perfomance del enlace enel tiempo, asi como los problemas de intermodulaciónque se generan por la corrosión de contactos (juntassemiconductoras), ruidos de recepción y variacionesdel nivel de señal transmitida.

La estanqueidad del dipolo se asegura me-diante el encapsulado en resinas sintéticas sumamenteresistentes y con protección contra la acción de losrayos UV. Estas resinas han sido probadas amplia-mente por más de 20 años en otros productos denuestra fabricación que funcionan expuestos a laintemperie, sin que se experimente degradación alguna.Entre las pruebas que se le realizan al dipolo, figura lade someterlo a inmersión en agua a 0,50 mt. durante10' a fin de comprobar su total estanqueidad.

El material utilizado en la construcción es a-leación de aluminio, soldado en atmósfera inerte(Argón). Los elementos de sujeción, son de acerogalvanizado por inmersión en caliente y de aceroinoxidable.

CONSTRUCCION

SUMA DE YAGIS

Botalón 31.75 x 2.0 mm.Diámetro de elementos parásitos(1) 12.7 x 1.5 mm.Elemento irradiante 19.05 x 1.5 mm. y 12.7 x 1.5 mm.Grampa de montaje toma hasta 50.8 mm.Máxima área expuesta 0.15 m2

Máxima velocidad de viento 150 Km. x horaDimensiones con embalaje 2110 x 910 x 130 mm.Peso sin embalaje 3.3 Kg.Peso con embalaje (en cartón) 7.3 Kg.

CARACTERISTICAS ELECTRICAS CARACTERISTICAS MECANICAS

(1) con refuerzo interior de 9.52 x 1.5 mm.

Se pueden obtener con las D7E-150BASganancias en azimut y elevación para diferentesusos, obteniendo control total sobre el lóbulo,mediante el apilamiento lado a lado y/o una encimade la otra y/o ambas, sumando en los distintos cam-pos (horizontal y/o vertical) suficiente cantidad de

yagis, para obtener tanto la ganancia como el cubrim-iento necesario. Podemos proveer los arneses deenfasado correspondientes en cada caso.

Nuestro Departamento de Ingeniería puedeasesorarlo al respecto.

DIAGRAMA EN EL CAMPO HORIZONTAL

Típica 10.1 mHz para 1.2:1 a centro de banda

R.O.E.

1.0

1.5

1.4

1.3

1.2

1.1

-4.5 -1.5 64.531.50-3

% de f0

+15

+10

+5

0

- 5

- 10

- 15

Las yagis D7E-150BAS pueden ser suma-das, a fin de lograr diagramas de radiación especia-les, como por ejemplo radiación bidireccional, eneste caso la ganancia se ve reducida en aproxi-madamente 3 dB en cada uno de los sentidos.

-6

Rango de frecuencia 120 a 200 MHz(*)Impedancia nominal 50 ohmRelación de ondas estacionarias ver gráficoAncho del lóbulo horizontal (-3DB) 47°Ancho del lóbulo vertical (-3 DB) 56°Ganancia (Sobre media onda) 10dBRelación antero posterior 17dBMáxima potencia de entrada 250 WattProtección contra descarga a tierraTerminación estandar conector "N" hembra(*)Especificar frecuencia con el pedido

+15

+10

+5

0

- 5

- 10

- 15

POLARIZACION VERTICALPOLARIZACION HORIZONTAL

La yagi soldada D7E-150BAS es unaantena direccional basada en la técnica desarrolladapor Yagi y Uda. Nuestro Departamento deInvestigación y Desarrollo ha optimizado la misma afin de obtener un gran ancho de banda, asi como muybaja R.O.E. y ganancia constante a través de toda labanda de operación.

El elemento irradiante, es un dipolo ple-gado de banda ancha, alimentado con un balun. Elconector coaxial de entrada es hembra "N" con pinzade contacto de Cobre-Berilio.

YAGI SOLDADA 10 DBD7E-150BAS 120 A 200 MHz

D7E150BAS

0°

330° 30°

300° 60°

270° 90°

240° 120°

210° 150°

180°

0°

330° 30°

300° 60°

270° 90°

240° 120°

210° 150°

180°