0600 - WOODS, PLASTICS, COMPOSITES 0610 Rough ...ODB Master - Division 6 – Wood, Plastics, Composites (06/20/16) 0610 - 3 c. Set structural members level, plumb, and true to line

ODB Master - Division 6 – Wood, Plastics, Composites (06/20/16)

0610 - 1

0600 - WOODS, PLASTICS, COMPOSITES

0610 Rough Carpentry

A. General Requirements: The provisions of the General Conditions of Subcontract shall apply to all work of this section.

B. Scope: Furnish all labor, materials, equipment and services necessary or reasonably incidental to complete all rough carpentry work shown on the drawings or described herein. This specification does not attempt to describe in detail all items necessary to carry on the work, but lists the following items of major importance: cant strips, blocking, nailing strips, grounds, wood framing, sheathing, subflooring, overhead door framing and blocking.

This subcontractor is not responsible for temporary enclosures and protection of construction, temporary stairs, and guard rails, unless otherwise noted.

C. Materials: Rough carpentry, framing lumber and blocking shall be standard and better Fir, or equal. Roof curbs shall be located and sized to suit requirements of the Mechanical Contractor. Cant strip shall be nominal 4x4 or 6x6 cut diagonally as indicated on the drawings. Rough hardware shall be of the type appropriate for the location and use, and include such items as nails, screws, washers, bolts, anchors, hangers, etc. Rough hardware items, if exposed to the exterior, shall be cadmium coated, non-corrosive and non-staining. All materials shall be in conformance with local and state codes and regulations.

1. Dimension Lumber: Comply with American Softwood Lumber Standard PS 20 and requirements of specified grading agencies.

a. If no species is specified, provide any species graded by the agency specified; if no grading agency is specified, provide lumber graded by any grading agency meeting the specified requirements.

b. Grading Agency: Any grading agency whose rules are approved by the Board of Review, American Lumber Standard Committee (www.alsc.org) and who provides grading service for the species and grade specified; provide lumber stamped with grade mark unless otherwise indicated.

c. All lumber installed within exterior walls shall be fire retardant treated.

d. Manufacturers:

i. iLevel by Weyerhaeuser: www.ilevel.com.

ii. Boise Cascade: www.bc.com.

iii. Georgia-Pacific Corp.: www.gp.com.

http://www.ilevel.com/

http://www.bc.com/

http://www.gp.com/


0610 - 2

iv. Louisiana Pacific Corp: www.lpcorp.com.

v. Roseburg Forest Products: www.roseburg.com.

2. Accessories:

a. Fasteners and Anchors:

i. Metal and Finish: Hot-dipped galvanized steel per ASTM A 153/A 153M.

ii. Anchors: As indicated on the structural drawings.

iii. Treated Wood Fasteners and Anchors: Conform to wood treatment manufacturer's recommendations for materials and finishes.

b. Wood Construction Connectors: Hot dipped galvanized steel, not less than 18 gage thick, sized to suit framing conditions and as indicated. Provide products manufactured by Simpson Strong-Tie Co. or approved equal.

i. For contact with preservative treated wood, provide minimum G185 galvanizing per ASTM A 653/A 653M.

c. Sill Gasket: 1/4 inch thick, plate width, closed cell plastic foam from continuous rolls.

d. Subfloor Glue: ASTM D 3498 or APA Specification AFG-01, Waterproof, water base, air cure type, cartridge dispensed.

i. Maximum Moisture Content of Lumber: [19 percent].

D. Workmanship: Install all cant strips, wood blocking and framing. Framing and blocking shall be cut with true tight joints and adequately fastened. Framing shall be performed in accordance with local and state codes and regulations, and in a manner acceptable to subsequent work. Install all rough wood blocking, grounds, etc., of size and shape and as necessary to properly secure other work and equipment in place. Install all framing in accordance with the following tolerances: Framing Members – ¼” from true position, maximum. Surface Flatness of Floor or Ceiling/Roof: 1/8” in 10 feet maximum, and ¼” in 30 feet maximum. Properly dispose of all waste and do not leave any wood, shavings, sawdust, etc. on the ground or buried in fill. Prevent sawdust and scrap material from entering storm drainage or other piping.

1. Framing Installation:

a. Select material sizes to minimize waste.

b. Reuse scrap to the greatest extent possible; clearly separate scrap for use on site as accessory components, including: shims, bracing, and blocking.

http://www.lpcorp.com/

http://www.roseburg.com/


0610 - 3

c. Set structural members level, plumb, and true to line. Discard pieces with defects that would lower required strength or result in unacceptable appearance of exposed members.

d. Make provisions for temporary construction loads, and provide temporary bracing sufficient to maintain structure in true alignment and safe condition until completion of erection and installation of permanent bracing.

e. Install structural members full length without splices unless otherwise specifically detailed.

f. Comply with member sizes, spacing, and configurations indicated, and fastener size and spacing indicated, but not less than required by applicable codes and AFPA Wood Frame Construction Manual.

g. Install horizontal spanning members with crown edge up and not less than 1-1/2 inches of bearing at each end, unless otherwise indicated.

h. Construct double joist headers at floor and ceiling openings unless otherwise indicated; use metal joist hangers unless otherwise detailed.

i. Provide bridging at joists in excess of 8 feet span at mid-span for spans of 8 to 16 feet; for spans greater than 16 feet provide bridging at third points of span. Fit solid blocking at ends of members.

j. Frame wall openings with two or more studs at each jamb; support headers on trimmer studs.

k. Lap ends of joists 4 inches minimum when framing from opposite sides of partitions and "under-set" beams.

l. Install headers at floor/ceiling assemblies as flush headers unless otherwise indicated.

m. Frame exterior corners so that insulation can be installed after exterior sheathing is installed.

n. Frame intersections of interior partitions with exterior walls so that insulation can be installed between the partition wall and exterior sheathing after exterior sheathing is installed.

2. Blocking, Nailers and Supports:

a. Provide framing and blocking members as indicated or as required to support finishes, fixtures, specialty items, and trim. If ceiling-hung toilet partitions are specified on the plans or in Section 1021, provide all necessary overhead support for partitions.

b. In framed assemblies that have concealed spaces, provide solid wood fire blocking as required by applicable local code, to close concealed draft openings between floors and between top story and roof/attic space; other material acceptable to code authorities may be used in lieu of solid wood blocking.


0610 - 4

c. In walls, provide blocking attached to studs as backing and support for wall-mounted items, unless item can be securely fastened to two or more studs or other method of support is explicitly indicated.

d. Where ceiling-mounting is indicated, provide blocking and supplementary supports above ceiling, unless other method of support is explicitly indicated.

e. Specifically, provide the following non-structural framing and blocking:

i. Cabinets and shelf supports.

ii. Wall brackets.

iii. Handrails.

iv. Grab bars.

v. Towel and bath accessories.

vi. Wall-mounted door stops.

vii. Chalkboards and marker boards.

viii. Wall paneling and trim.

ix. Joints of rigid wall coverings that occur between studs.

x. Fire extinguisher cabinets.

xi. Electrical panelboards.

xii. Any other materials shown on the drawings.


0620 - 1

0620 Finish Carpentry


B. Scope: Furnish all labor, equipment and services necessary or reasonably incidental to install all finish carpentry work shown on the drawings or described herein. This specification does not attempt to describe in detail all items necessary to carry on the work, but lists the following items of major importance: installation of hollow metal and wood doors, installation of wood frames, installation of finish hardware, installation of plastic laminate and cultured marble work (including sills if applicable), installation of cabinets, millwork, and trim, installation of toilet accessories.

This subcontractor is not responsible for temporary enclosures and protection of construction, temporary stairs, and guard rails, unless otherwise noted.

C. Materials: Lumber and blocking shall be standard and better Fir, or equal. Rough hardware shall be of the type appropriate for the location and use, and include such items as nails, screws, washers, bolts, anchors, hangers, etc. Rough hardware items, if exposed to the exterior, shall be cadmium coated, non-corrosive and non-staining. All materials shall be in conformance with local and state codes and regulations.

Finish carpentry materials shall be furnished under Sections 0640, 0661, etc.

D. Workmanship:

1. Install all cabinets, millwork, plastic laminate work, cultured marble, trim, finished pieces, hollow metal and wood doors, and wood door and window frames. Use miters on all corners and splices. Nailing shall be blind wherever possible. Nailing on exposed surfaces of finished materials shall be set. Trim shall be installed in pieces as long as possible with joints only at solid supports. Doors shall be installed with 1/8" clearance on tops and both sides and 3/16" clearance at threshold, unless otherwise shown. Doors in openings without thresholds shall be undercut 3/4" unless otherwise shown. Cut plastic laminate countertops for all sinks and lavatories.

2. Carefully scribe work abutting other components, with maximum gaps of 1/32 inch. Do not use additional overlay trim to conceal larger gaps.

3. Standing and Running Trim: Install with minimum number of joints possible, using full-length pieces from maximum length of lumber available. Cope at returns, miter at corners to produce tight fitting joints. Use scarf joints for end-to-end joints. Provide miter returns at all ends of pre-finished materials.

4. Install hardware in accordance with manufacturer's instructions


0620 - 2

5. Receive and store all finish hardware. Properly sort, tag and file all keys. Fit and install all finish hardware, except as otherwise indicated. Hardware shall be fitted before final coat of paint, stain or sealer is applied, and installed after painting and finishing has been completed.


0640 - 1

0640 Architectural Woodwork


B. Scope: Furnish all millwork shown on the drawings, described herein, or reasonably incidental for a complete installation. In general, the work under this section includes furnishing all cabinets, countertops, cultured marble, toilet room vanity tops, shelving, paneling, trim, handrails, wood door frames, wood window frames, and the furnishing and application of all finish hardware associated with the millwork. Wood doors are furnished under a separate section.

C. Submittals:

1. Product Data: For each variety of material, accessory, and manufactured product.

2. Shop Drawings: Include plans, sections, details, and attachments to other work.

D. Materials:

1. Millwork and trim shall meet the requirements of the Architectural Woodwork Institute, custom grade for exposed transparent finish.

2. Hardwood: Exposed hardwood for natural finish shall be premium grade red oak, plain sawed, kiln dried, selected for uniformity of color and grain. Sizes and shapes as indicated, continuous length wherever practical and any spliced lengths to match.

3. Hardwood Plywood: Exposed plywood shall be custom grade red oak rotary sliced veneer on lumber, veneer, particle board, fiberboard or wood ladder cores. Veneer shall be 1/28" minimum thickness. Veneer on any door or panel face with two or more pieces shall be matched.

4. Concealed Members: Cabinet members, completely concealed from view, may be of any species, unless otherwise noted.

5. Softwood: Softwood shall be custom grade Ponderosa Pine or Idaho White Pine, kiln dried.

6. Plastic Laminate: Shall be standard 1/16" thick "Formica" by Formica Company, or approved equal. Colors as selected by the contractor from full range of manufacturer's solid colors.

7. Cultured Marble Lavatory Units: Shall be of the size and type shown. Units shall be polyester resin base, inert mineral filled, one piece, cast vanity tops with integral bowl and shall meet or exceed all quality requirements of the Cultured Marble Institute LS 2-76, "Property and Performance Standard for Cultured Marble


0640 - 2

Lavatories," as published by the Cultured Marble Institute, and shall be in conformance with local and state codes and regulations.

8. Glue and Adhesive: Glue and adhesive shall conform to AWI Adhesive Performance Requirements, appropriate for its intended use.

9. Cabinet Hardware: Provide all base and wall cabinet doors and drawers with pulls, catches, hinges, and miscellaneous hardware as noted on plans such as adjustable standards and drawer extensions. All hardware, except cabinet door and drawer pulls, shall be installed on cabinets prior to delivery. Pulls shall be "EPCO MC-42" wire type or approved equal. Hinges shall be "Stanley" concealed pin or approved equal. Catches shall be magnetic with metal case. Submit samples of each for approval.

10. Miscellaneous Hardware: All items by Knape & Volgt Manufacturing Company, Grand Rapids, Michigan, or equal, except as otherwise indicated.

a. Shelf Supports:

i. No. 255 Shelf Standards, bright zinc plate finish.

ii. No. 239 Shelf Supports, bright zinc plate finish.

b. Hanging Rods and Flanges:

i. No. 764 Heavy Duty Flanges, polished chrome finish.

ii. No. 770 Heavy Wall Steel Tubing, 1-5/16" outside diameter, polished chrome finish.

c. Sliding and Bifold Door Hardware: Provide complete commercial grade track and guide system for doors as shown on the plans. Hangers shall consist of adjustable nylon rollers. Pulls shall be rectangular recessed type for sliding doors, rectangular wire type pulls for bifold doors, with finish to match building hardware.

E. Fabrication:

1. Millwork details shall conform to the flush overlay design details of the AWI. All items of millwork shall be fabricated and assembled at the shop insofar as possible. Millwork shall be built and fitted together at the shop in sections and fastened according to detail drawings. Fasteners shall be blind where possible. All work shall be left smooth, free from hammer or tool marks, slivers or open joints.

2. Millwork shall be assembled with hairline joints, all pieces being mortise and tennoned or tongue and grooved. Conceal cleats and fastening devices. Fabricate of clamped hot glued construction.

3. Fabricate plastic laminate in accordance with manufacturer's printed instructions. For vanity countertops, or countertops in wet locations, install over 3/4" thick mahogany faced marine plywood. For all other locations, install over 3/4" thick


0640 - 3

particle board. Provide standard balancing sheets on all backs. On vanity countertops, backsplash, top and front return to be one piece plastic laminate with minimum radii. Sidesplashes adjacent to a wall shall be provided where shown, and applied press fit in the field.

4. All required case backs and drawer bottoms shall have a minimum thickness of 1/4". All adjustable shelving unsupported for a length of 36" shall have a minimum thickness of 1".

5. Particular care shall be exercised to ensure uniformity of color in adjoining hardwood and hardwood veneers. All items shall be uniformly sanded prior to shipping to site and provisions shall be made to accommodate all items furnished by others.

6. Exposed cabinet door and drawer front edges may be exposed fiberboard core. Exposed cabinet door and drawer front edges fabricated with plywood or particleboard cores shall have hardwood edges.


0661 - 1

0661 Solid Surface Countertops


B. Scope: Furnish and install all solid surface countertops shown on the drawings.

C. Submittals:

1. Product Data: For each variety of solid surface, accessory, and manufactured product.

2. Shop Drawings: Include plans, sections, details, and attachments to other work. Show locations and details of joints. Show direction of veining, grain, or other directional patterns.

D. Materials:

1. Nominal Thickness: Provide thickness indicated, but not less than 3/4 inch (20 mm). Gage backs to provide units of identical thickness.

2. Edge Detail: Straight, slightly eased at top or as indicated on drawings.

3. Splashes: Provide 3/4-inch (20 mm) thick backsplashes and end splashes unless otherwise indicated. Height: 4 inches (100 mm) or as indicated on the drawings. Top-Edge Detail: Straight, slightly eased at corner or as indicated on the drawings.

4. Joints: Fabricate countertops in sections for joining in field, with joints at locations indicated and as follows:

a. Bonded Joints: 1/32 inch (0.8 mm) or less in width.

b. Grouted Joints: 1/16 inch (1.5 mm) in width.

c. Sealant-Filled Joints: 1/16 inch (1.5 mm) in width.

d. Splined Joints: Accurately cut kerfs in edges at joints for insertion of metal splines to maintain alignment of surfaces at joints where indicated. Make width of cuts slightly more than thickness of splines to provide snug fit. Provide at least three splines in each joint.

5. Under Counter Fixtures:

a. Make cutouts for under counter fixtures in shop using template or pattern furnished by fixture manufacturer. Form cutouts to smooth, even curves.


0661 - 2

b. Provide vertical edges, slightly eased at juncture of cutout edges with top and bottom surfaces of countertop and projecting 3/16 inch (5 mm) into fixture opening.

6. Counter-Mounted Fixtures:

a. Prepare countertops in shop for field cutting openings for counter-mounted fixtures. Mark tops for cutouts and drill holes at corners of cutout locations. Make corner holes of largest radius practical.

7. Fittings:

a. Drill countertops in shop for plumbing fittings, under counter soap dispensers, and similar items.

E. Installation Tolerances:

1. Variation from Level: Do not exceed 1/8 inch in 96 inches (3 mm in 2400 mm), 1/4 inch (6 mm) maximum.

2. Variation in Joint Width: Do not vary joint thickness more than one-fourth of nominal joint width.

3. Variation in Plane at Joints (Lipping): Do not exceed 1/64-inch (0.4-mm) difference between planes of adjacent units.

4. Variation in Line of Edge at Joints (Lipping): Do not exceed 1/64-inch (0.4-mm) difference between edges of adjacent units, where edge line continues across joint.

F. Workmanship:

1. Examine substrates to receive countertops and conditions under which countertops will be installed, with Installer present, for compliance with requirements for installation tolerances and other conditions affecting performance of solid surface countertops.

2. General: Install countertops with silicone adhesive in a manner that will allow easy removal if required.

3. Do not cut countertop in field unless otherwise indicated. If solid surface countertops or splashes require additional fabrication not specified to be performed at Project site, return to fabrication shop for adjustment.

4. Do necessary field cutting as countertop is set. Use grinders or power saws with recommended blades and dust suppression systems to cut countertop. Cut lines straight, true, and at right angles to finished surfaces unless beveling is required for clearance. Ease edges slightly to prevent snipping.

5. Set solid surface countertops to comply with requirements indicated. Shim and adjust to locations indicated, with uniform joints of widths indicated and with edges and faces aligned according to established relationships and indicated tolerances.


0661 - 3

6. Bond joints with adhesive and draw tight as countertops are set. Mask areas of countertops adjacent to joints to prevent adhesive smears.

7. Install metal splines in kerfs in edges at joints where indicated. Fill kerfs with adhesive before inserting splines and remove excess immediately after adjoining units are drawn into position.

8. Clamp units to temporary bracing, supports, or each other to ensure that countertops are properly aligned and joints are of specified width.

9. Complete cutouts not finished in shop. Mask areas of countertops adjacent to cutouts to prevent damage while cutting. Use power saws with recommended blades to cut countertop material. Make cutouts to accurately fit items to be installed, and at right angles to finished surfaces unless beveling is required for clearance. Ease edges slightly to prevent snipping.

11. Install backsplashes and end splashes by adhering to wall with silicone adhesive and to countertops with solid surface adhesive. Mask areas of countertops and splashes adjacent to joints to prevent adhesive smears.

G. Adjusting and Cleaning:

1. In-Progress Cleaning: Clean countertops as work progresses. Remove adhesive, grout, mortar, and sealant smears immediately.

2. Remove and replace solid surface countertops of the following description:

a. Broken, chipped, stained, or otherwise damaged solid surface material. Solid surface material may be repaired if methods and results are approved by Architect.

b. Defective countertops.

c. Defective joints, including misaligned joints.

d. Solid surface countertops and joints not matching approved Samples and mockups.

e. Solid surface countertops not complying with other requirements indicated.

3. Replace in a manner that results in solid surface countertops matching approved samples and mockups, complying with other requirements, and showing no evidence of replacement.

4. Clean solid surface countertops no fewer than six days after completion of installation, using clean water and soft rags. Do not use wire brushes, acid-type cleaning agents, cleaning compounds with caustic or harsh fillers, or other materials or methods that could damage countertop.

5. Sealer Application: Apply solid surface sealer to comply with countertop producer's and sealer manufacturer's written instructions.

Division 7 – Thermal and Moisture Protection (06/20/16) Xcel Energy – SPS Amarillo – Headquarters Office

7 - 1

7.4. Building Insulation

A. General Requirements: The provisions of the General Conditions of Subcontract apply to all work of this section.

B. Scope: Furnish all labor and materials required for the complete thermal insulation, slab edge fire and smoke safing and slab/wall related fire containment systems where shown on the plans or as required by code. 1. Perimeter wall insulation, safing insulation and smoke barrier, and building

insulation related to glass and glazing, precast or slab edge to wall installations are all included under this section.

2. Provide continuous foil faced plenum rated vapor barrier at all perimeter insulation areas. Alternative vapor barrier materials and systems must be approved by Contractor in writing prior to contract award.

3. Furnish and install aluminum gutter drainage system at lower inside face of all precast spandrels and weep to face of building.

All systems shall be designed in conformance with UL, applicable building

codes and local code authority requirements. It shall be the responsibility of

this subcontractor to gain local code authority approvals for all designs and

installations required by this section.

C. Material:

1. Manufacturers: Subject to compliance with requirements, provide insulation products of one of the following:

a. Extruded Polystyrene Board Insulation- Amoco Foam Products

Co., DiversiFoam Products, The Dow Chemical Co., UC Industries, Inc. or Owens/Corning-UC Industries, Inc.

b. Polyisocyanurate Board Insulation: Celotex, Building Products Div.,

The Celotex Corporation.

c. Glass Fiber Insulation: CertainTeed Corp., KnaufFiber Glass, Manville Building Insulation Div. or Owens/Coring Fiberglass Corp.

d. Semi-Refractory Fiber Insulation: Cafco Industries Ltd., Fibrex Inc.

or Thermafiber Division of USG Interiors, Inc.

2. Insulating Materials:

a. General: Provide insulating materials that comply with requirements and with referenced standards.

1. Preformed Units: Sizes for applications indicated, selected

from manufacturer's standard thicknesses, widths, and lengths.


0661 - 1

b. Extruded Polystyrene Board Insulation: Not accepted for use in

project unless specifically authorized by Contractor in writing prior to contract award.

c. Polyisocyanurate Board Insulation: Rigid, cellular thermal

insulation with glass-fiber-reinforced polyisocyanurate closed-cell foam core and aluminum foil facing laminated to both sides; complying with FS HH- I-1972/1, Class 2; aged r-values of 8 and 7.2 at 40 and 75 deg. F (4.4 and 23.9 deg. C), respectively; and as follows:

i. Surface Burning Characteristics: Maximum flame

spread and smoke developed values of 20 and 200,

respectively.

d. Unfaced Mineral Fiber Blanket/Batt Insulation: Thermal insulation

produced by combining mineral fibers of type described below with thermosetting resins to comply with ASTM C 665 for Type I (blankets without membrane facing); and as follows:

i. Mineral Fiber Type: Fibers manufactured from glass or slag.

ii. Surface Burning Characteristics: Maximum flame spread

and smoke developed values of 25 and 50, respectively.

e. Faced Mineral Fiber Blanket/Batt Insulation: Thermal insulation produced by combining mineral fibers of type described below with thermosetting resins to comply with ASTM C 665 for Type III, Class A (blankets with reflective vapor-retarder membrane facing with flame spread of 25 or less); foil-scrim-kraft or foil-scrim-polyethylene vapor- retarder membrane on one face, and as follows:

i. Mineral Fiber Type: Fibers manufactured from glass or slag.

ii. Surface Burning Characteristics: Maximum flame spread

and smoke developed values of 25 and 50, respectively.

iii. Flanged Units: Provide blankets/batts fabricated with facing incorporating 4-inch-wide flanges along their edges for attachment to framing members.

f. Closed-Cell Spray Polyurethane Foam Insulation

i. Minimum density of 1.5 lb/cu. Ft., thermal resistivity of 6.2 deg F x h x sq. ft./Btu x in. at 75 deg F. Demilec Heatlok Soy or approved equal.

3. Safing Insulation and Accessories:

a. Semi-Refractory Fiber Board Safing Insulation: Semi-rigid boards


0661 - 2

designed for use as a fire stop a openings between edge of slab and exterior wall panels, produced by combining semi-refractory mineral fiber manufactured from slag with thermosetting resin binders to comply with ASTM C 612, Class 1 and 2; nominal density of 4.0 pcf; passing ASTM E 136 for combustion characteristics; r-value of 4.0 at 75 deg. F (23.9 deg. C).

b. Caulking Compound: Material approved by manufacturer of safing

insulation for sealing joint between foil backing of safing insulation and edge of concrete floor slab against penetration of smoke.

c. Safing Clips: Galvanized steel safing clips approved by

manufacturer of safing insulation for holding safing insulation place.

4. Vapor Retarders:

a. Polyethylene Vapor Retarder: ASTM D 4397, 6.0 mils thick, with a

maximum permeance rating of 0.13 perms.

b. Foil Faced Vapor Retarder: Meet applicable industry standards for performance under ASHRAE summer and winter design conditions for the state in which the project is located.

c. Tape for Vapor Retarder: Pressure sensitive tape of type

recommended by vapor retarder manufacturer for sealing joints and penetrations in vapor retarder.

5. Auxiliary Insulating Materials:

a. Adhesive for Bonding Insulation: Product with demonstrated

capability to bond insulation or mechanical anchors securely to substrates indicated without damaging or corroding either insulation, anchors, or substrates.

b. Protection Board: Premolded, semi-rigid asphalt/fiber composition

board, 1/4 inch thick, formed under heat and pressure, standard sizes.

D. Workmanship:

1. Examination:

a. Examine substrates and conditions with substrate installer present, for compliance with requirements of the Section which substrates and related work are specified and to determine if other conditions affecting performance of insulation are satisfactory. Do not proceed with installation of insulation until unsatisfactory conditions have been corrected.

2. Preparation:


0661 - 3

a. Clean substrates of substances harmful to insulation or vapor retarder, including removal of projections that might puncture vapor retarders.

b. Close off openings in cavities receiving poured-in-place insulation

to prevent the escape of insulation. Provide bronze or stainless steel screen (inside) where openings must be maintained for drainage or ventilation.

3. Installation, General:

a. Comply with insulation manufacturer's instructions applicable to

products and application indicated. If printed instructions are not available or do not apply to project conditions, consult manufacturer's technical representative for specific recommendations before proceeding with installation of insulation.

b. Extend insulation full thickness as indicated to envelop entire area

to be insulated. Cut and fit tightly around obstructions, and fill voids with insulation. Remove projections that interfere with placement.

c. Apply a single layer of insulation of required thickness, unless

otherwise shown or required to make up total thickness.

4. Installation of Perimeter Foundation and Under-Slab Insulation:

a. On vertical surfaces, set units in adhesive applied in accordance with manufacturer's instructions. Use type of adhesive recommended by manufacturer of insulation.

b. Protect below-grade insulation on vertical surfaces (from damage

during back-filing) by application of protection board. Set in adhesive in accordance with recommendations of manufacturer of insulation.

c. Protect top surface of horizontal insulation (from damage during

concrete work) by application of protection board.

5. Installation of General Building Insulation:

a. Apply insulation units to substrate by method indicated, complying with manufacturer's recommendations. If no specific method is indicated, bond units to substrate with adhesive or use mechanical anchorage to provide permanent placement and support of units.

b. Seal joints between closed-cell (nonbreathing) insulation units by

applying adhesive, mastic, or sealant to edges of each unit to form a tight seal as units are shoved into place. Fill voids in completed installation with adhesive, mastic, or sealant as recommended by insulation manufacturer.


0661 - 4

c. Set vapor retarder faced units with vapor retarder to warm side of construction, except as otherwise indicated. Do not obstruct ventilation spaces, except for firestopping. Tape joints and ruptures in vapor retarder, and seal each continuous area of insulation to surrounding construction to ensure airtight installation.

d. Set reflective, foil-faced units accurately with not less than 0.75-

inch air space in front of foil as indicated.

6. Installation of Safing Insulation:

a. Building Insulation: Install safing insulation to fill gap between edge of concrete floor slab and back of exterior spandrel panels on safing clips spaced as needed to support insulation and to meet UL requirements. Cut safing insulation wider than gap to be filled to ensure compression fit and seal joint between insulation and edge of slab with caulking approved by safing insulation manufacturer for this purpose. Leave no voids in completed installation. Provide slab edge to exterior wall smoke seal as required by the City of Mounds View.

b. Design and install a fire containment system at the perimeter wall

below and above the slab edge as required by the City of Mounds View. All required approvals shall be obtained by this Subcontractor.

7. Installation of Vapor Retarders:

a. General: Extend vapor retarder to extremities of areas to be

protected from vapor transmission. Secure in place with adhesives or other anchorage system as indicated. Extend vapor retarder to cover miscellaneous voids in insulated substrates, including those filed with loose fiber insulation.

b. Seal vertical joints in vapor retarders over framing by lapping not

less than 2 wall studs. Fasten vapor retarders to framing at top, end, and bottom edges, at perimeter of wall openings, and at lap joints; space fasteners 16 inches o.c.

c. Seal overlapping joints in vapor retarders with adhesives or tape per

vapor retarder manufacturer's printed directions. Seal butt joints and fastener penetrations with tape of type recommended by vapor retarder manufacturer. Locate all joints over framing members or other solid substrates.

d. Firmly attach vapor retarders to substrates with mechanical

fasteners or adhesives as recommended by vapor retarder manufacturer.

e. Seal joints caused by pipes, conduits, electrical boxes, and similar

items penetrating vapor retarders with tape of type recommended by vapor retarder manufacturer to create an airtight seal between


0661 - 5

penetrating objects and vapor retarder.

f. Repair any tears or punctures in vapor retarders immediately before concealment by other work. Cover with tape or another layer of vapor retarder.

8. Protection:

a. General: Protect installed insulation and vapor retarders from damage due to harmful weather exposures physical abuse, and other causes. Provide temporary coverings or enclosures where insulation will be subject to abuse and cannot be concealed and protected by permanent construction immediately after installation.

ODB Master - Division 8 - Doors and Glazing Openings (06/20/16)

0810 - 1

0800 DOORS AND GLAZING OPENINGS

8.1 Doors, Frames and Hardware

Hollow Metal Doors and Frames


B. Scope: Provide all labor, materials, equipment and services necessary and reasonably incidental to complete Hollow Metal Doors and Frames in accordance with the Contract Documents

C. Materials:

1. Frames:

a. Steel frames, unless otherwise noted, shall be welded type, with mitered corners, of the size, types and styles indicated on the drawings, 16 gauge unless otherwise indicated, prime painted, with adequate and suitable jamb and floor anchors as required for wall and service conditions, minimum of three jamb anchors per door. Frames shall be mortised, reinforced, and prepared to receive all scheduled hardware. Enclose strike and hinge reinforcement with plaster guards where required. Provide rubber door silencers, minimum three per door.

b. Fabricate frames of one piece welded construction, ground smooth, with mitered corners, for locations indicated on the drawings and for all frames with transoms or sidelights.

2. Doors: Steel doors shall be of size, type and style indicated on the drawings, 1-3/4" thick - 18 gauge unless otherwise indicated, free from all defects, prime painted, mortised, reinforced, and prepared to receive all scheduled hardware. Provide cutouts and frames for lights as indicated. Provide cutouts, frames and sight proof louvers as indicated. Provide core support as required to adequately support the face panels. All exterior doors shall have flush tops.

3. Prime Paint: Chemically treat all frames and doors and paint with a uniform coat of rust inhibiting quality primer, oven dried.

4. Acoustical Qualities: Doors requiring specific acoustic qualities shall have sound transmission classification rating as indicated on the drawings.

5. Insulation Qualities: All exterior doors, and others as indicated on the drawings to be insulated, shall have a maximum "U" factor of 0.2.

6. Provide labeled fire doors and frames, as indicated on the drawings, of a type which has been approved in accordance with local code enforcement requirements.


0810 - 2

D. Workmanship:

1. Doors and frames shall be fabricated of top quality material, best workmanship, and in accordance with best industry standards.

2. Doors and frames shall be erected plumb and in true alignment. Frames shall be rigid and securely anchored. Doors shall be installed in a manner to achieve the intended operation.

E. Submittals: Submit three (3) sets of hard copies and one (1) electronic copy of the complete materials list, manufacturer's specifications and data, and shop drawings indicating all frames and doors, types, sizes, details, anchors, reinforcing, hardware, etc.

Interior Aluminum Frames


B. Scope: Provide all aluminum frame work such as sidelights, borrowed lights, transoms, and other openings, complete in place, as indicated on the drawings. All bids for aluminum frames shall be combined with furnishing all hollow metal doors, frames and door hardware.

C. Materials:

1. Aluminum alloy 6063-T5 extruded and fabricated to shapes as required for each application, for knock-down field assembly.

2. Nominal wall thickness of Main Frame Member: .062 inches.

3. Hinge and strike backing plates to be drilled, tapped and installed by frame manufacturer. Backing plates to be aluminum alloy 6063-T5 with a nominal thickness of 0.125 inches.

4. Fasteners and Hardware: Aluminum, stainless steel, or other non-corrosive materials compatible with aluminum and acceptable to frame manufacturer.

5. Provide continuous PVC vinyl smoke seal or mohair around perimeter of door stop.

6. All frame members shall arrive at jobsite; mortised, drilled and tapped for hinges and strike locations.

7. Frame design must allow installation over prefinished walls.


0810 - 3

8. Profile shall be 1½ inches standard or custom casing as selected by Architect, 5/16 inch minimum wall standoff required.

9. Secure templates from the finish hardware supplier, and accurately install, or make provision for, all finish hardware at the factory (where required).

10. Finish and Trim Profile: Anodized Finish: Class II, clear or colored anodized finish.

D. Workmanship:

1. Frames shall be fabricated of top quality material, best workmanship, and in accordance with best industry standards.

2. Frames shall be erected plumb and in true alignment. Frames shall be rigid and securely anchored.

E. Submittals: Submit three (3) sets of hard copies and one (1) electronic copy of the complete materials list, manufacturer's specifications and data, and shop drawings indicating all frames, types, sizes, details, anchors, reinforcing, hardware, etc.

Wood Doors


B. Scope: Provide all labor, materials, equipment and services necessary and reasonably incidental to complete Wood Doors in accordance with the Contract Documents

C. Materials:

1. Wood doors shall be of the size, type and style indicated on the drawings which meet or exceed ANSI/WDMA I.S.1A-13series, and Architectural Woodwork Insti-tute for Type PC (particle core), Type SHC (hollow core), Type FD (fire door), or Type SR (sound retardant).

Warranties shall be manufacturer's standard for type and use of door.

Doors shall be complete with all cutouts, frames, trim, and sightproof louvers. Trim and louvers shall be hardwood to match face panels.

Doors shall be premachined for butts and for locksets, unless supplier specifically quotes otherwise.

2. Wood Veneer Facings:


0810 - 4

a. For all unpainted doors scheduled to receive stained or natural finish provide seven ply, premium grade select natural red oak, unless otherwise indicated, plain sliced with manufacturer's standard stiles.

b. For all doors scheduled to be painted provide sound grade birch or tempered hardboard with factory applied prime coat of paint.

3. Plastic Laminate Clad Doors: Face doors with 1/16" general purpose high pressure plastic laminate from Formica, Micarta, Wilson Art, or approved equal. Vertical stiles shall be manufacturer's standard stained or painted.

4. Provide labeled fire doors as indicated on the drawings of a type which has been approved in accordance with local code enforcement requirements.

5. Sound retardant doors as indicated on the drawings shall have STC ratings as follows:

a. 1-3/4" door - STC 36

b. 2-1/4" door - STC 42

Where necessary door supplier shall furnish automatic bottom seal, gasketed door stops, screws and finishing washers, etc.

D. Workmanship:

1. Submittals: Submit three (3) set of hard copies and one (1) electronic copy of complete materials list, manufacturer's specifications and data, and shop drawings indicating all doors, types, sizes, details, hardware preparation, etc., and a copy of guarantee.

2. Deliver all doors to jobsite in protective wrappings to prevent damage, unless supplier specifically quotes otherwise. Provide instructions regarding how to stack, dealing with building moisture/temperature, etc. to prevent warpage.

3. Installation of the work under this section is covered under Section 6 -Carpentry.

Finish Hardware


B. Scope: Provide all labor, materials, equipment and services necessary and reasonably incidental to complete Door Hardware in accordance with Contract Documents

C. Materials: All hardware furnished shall be free from defects, scratches, mars, etc., and shall be complete with all necessary screws, shields and other appurtenances as required


0810 - 5

for a complete installation. Where a fire rated assembly is scheduled, the hardware supplier shall provide the required hardware per his verification that the hardware groups scheduled are proper for the ratings and that the hardware group components are consistent with the rating requirements. The following hardware shall be provided relative to those items listed in the hardware schedule of this specification:

1. Panic Devices: Von Duprin or approved equal. Furnish thru-bolts and threaded sleeves on mineral-filled doors.

2. Locksets and Latchsets: Schlage, Yale, Corbin, Russwin or Sargent based on Government Specification comparison sheet, except that intermediate series duty locks are not considered equal to heavy duty series locks. All locksets to have 2-3/4" backsets, 1/2" throw and as required by Code. Lockset and latchset style shall be Schlage D-Rhodes/S-Saturn design, or equal, as noted in the hardware schedule. Provide tactile identification on door handles where required by the applicable local handicap code.

3. Closers: Norton, or approved equal, on exterior and interior doors. Furnish size as recommended by manufacturer, thru-bolt to hollow core or mineral-filled doors or as required. Use drop brackets where required. Allow door to swing maximum except as may be noted in each hardware group. Operation pressure to comply with local handicap code and ADA requirements.

4. Butts: Stanley, Lawrence, or approved equal, full mortise unless otherwise indicated, as follows:

a. Exterior Doors: Ball bearing butts, 5 knuckle, average frequency.

i. Up to 7'-6" high - 3 butts

ii. Over 7'-6" high - 4 butts

b. Exterior Entrance Doors: Ball bearing butts, 5 knuckle, high frequency.


ii. Over 7'-6" high - 4 butts

c. Interior Doors:


ii. Over 7'-6" high and dutch doors - 4 butts

d. Fire Doors: As required for door fire label.

e. All doors with closers: Ball bearing butts.

f. 1-3/4" door thickness: Minimum size 4 1/2"x 4 1/2".

5. Trim: Hiawatha or approved equal for pulls, push plates, kick plates, etc. Kick plates to be 16 gauge, 10" high and 2" less than door width.


0810 - 6

6. Stops and Holders: Glynn-Johnson WB50M or WB60M Series wall stop or approved equal where applicable. Where wall stops are not appropriate, furnish Glynn-Johnson GJ-410 Series overhead stop or approved equal. Where hold-open is specified, provide Glynn-Johnson W20X or approved equal.

7. Manual and Auto Flush Bolts, Coordinator and Dustproof Strikes: Glynn Johnson or approved equal, as scheduled, finish to match door hardware.

8. Surface Bolts: Ives 454 or equal.

9. Weatherstripping, Seals and Thresholds: Reese, or approved equal, as scheduled. Reese #4618 gasket seal, or approved equal as required by local code enforcement, at head and jambs of frames of 20 minute rated doors.

D. Finishes: The finish of all hardware shall be US26D dull chrome except as otherwise indicated. Restroom doors shall be provided with US28 aluminum hardware, except that the exterior pulls or push plates and kick plates shall be US26D dull chrome. Prime coated-butts and non-removable pins shall be furnished for exterior doors. Cylinders in aluminum entrance doors shall match the finish of the doors.

E. Submittals: Submit three (3) sets of hard copies and one (1) electronic copy of the finish hardware list for approval. Identify all catalog numbers by brand name or manufacturer. A complete keying schedule showing all keying by groups, submaster keying shall be developed through the cooperation of the Owner, Contractor and hardware Subcontractor. Hardware Subcontractor shall submit catalog cuts of all hardware from alternate manufacturers.

F. Hardware Schedule: See Sheet A6.2 in the Architectural Drawings


0880 - 1

ODB Master - Division 9 – Interior Finishes (06/20/16)

0910 - 1

0900 – INTERIOR FINISHES

0910 Metal Framing


B. Scope: Furnish all labor, materials, equipment and services necessary or reasonably incidental to complete all interior and exterior metal framing construction and all suspension systems for ceilings and soffits (with the exception of acoustical ceiling grid systems) shown on the drawings or described herein. Except where noted on the drawings, interior non-loading bearing partitions shall be constructed of metal studs and runners. Exterior walls, and other load bearing walls, where shown, shall be constructed of light gauge metal framing.

Install all welded hollow metal door and window frames located in metal stud partitions.

C. Materials: Metal studs and runners shall be U.S. Gypsum, or approved equal, channel type, galvanized steel. Sizes for all framing members shall be as indicated on the drawings. If sizes are not clear on the drawings, they shall conform to standards outlined in the manufacturer’s written literature.

Light gauge metal framing shall be prime painted and of a size and gauge as shown on the drawings. All accessories shall be as required by the drawings and manufacturers' printed specifications.

D. Workmanship: Metal studs and runners shall be framed and aligned accurately. Installation shall be in general accordance with Section I, Drywall and Veneer Construction Standards of the Gypsum Construction Handbook, prepared by United States Gypsum Company, adequately braced, true to line, plumb and level.

Light gauge metal framing shall be secured to the structural building frame as shown and noted on the drawings, and in accordance with the manufacturer's standard specifications and associated printed recommendations.

Accurately layout metal framing for walls and partitions in accordance with the drawings.

E. Submittals: Submit complete materials list, manufacturer's specifications and data, detailed shop drawings and related design calculations for all light gauge metal framing work.


0920 - 1

0920 Gypsum Drywall


B. Scope: Furnish and install gypsum drywall construction complete with taped and sanded joints and exterior gypsum sheathing in accordance with drawings and specifications, applicable codes and Section I, Drywall and Veneer Construction Standards of the Gypsum Construction Handbook, prepared by United States Gypsum Company.

Install hollow metal door and window frames furnished under Section 0810 that are located in gypsum drywall partitions. Provide all sound control and insulation blankets, and vapor barriers as indicated on the drawings and specified herein.

C. Materials: All materials shall be in conformance with applicable codes and regulations.

1. Gypsum Wallboard: Gypsum wallboard shall be of the type and thickness shown on the drawings with long edges tapered. Sizes shall be 4'-0" wide and length as required by job conditions. Gypsum sheathing shall be of the type and thickness shown on the drawings. Board shall conform to Standard Specification for Gypsum Wallboard, ANSI/ASTM C1396 and other ASTM standards as applicable.

2. Joint Reinforcing Tape and Joint Compound: Joint reinforcing tape and joint compound adhesive materials shall conform to Standard Specification for Joint Treatment Materials for Gypsum Wallboard Construction, ANSI/ASTM C475.

3. Screws: Screws shall be appropriate length self tapping Phillips head drywall screws.

4. Sound Control and Insulation: Sound control and insulation blankets shall be of the type and thickness as indicated on the drawings.

5. Corner Bead: Galvanized 28 gauge steel corner bead 1-1/4" x 1-1/4".

6. Metal Trim: Galvanized 28 gauge steel metal trim.

7. Control Joints: USG #093 control joints.

8. Vapor Barriers: Vapor barriers, or foil backed gypsum wallboard panels, where indicated on the drawings, shall meet ASTM requirements for a vapor permeance not exceeding 0.30 perm.

9. Delivery, Handling and Storage: All materials shall be delivered in the original packages, containers or bundles bearing the brand name and the name of the manufacturer or the supplier for whom the product is manufactured. All materials shall be kept dry, preferably by being stored inside the building under the roof. Where necessary to store gypsum wallboard outside, it shall be stacked off the ground, properly supported on a level platform and fully protected from the


0920 - 2

weather. Gypsum wallboard shall be neatly stacked flat with care taken to avoid undue sagging or damage to edges, ends and surfaces.

D. Workmanship:

1. Preparation: Examine and inspect materials to which gypsum board is to be applied. Remedy all defects prior to installation of drywall.

2. General Installation: Gypsum wallboard should be applied vertically, whenever practical, or where required by code. Boards of maximum practical length shall be used such that there will be an absolute minimum number of end joints.

3. Fastening: Gypsum wallboard and sheathing shall be screwed to metal stud framing in accordance with Section I, Drywall and Veneer Construction Standards of the Gypsum Construction Handbook, prepared by United States Gypsum Company, and applicable codes.

4. Joint and Corner Finishing: Fill all nail holes and screw heads. Treat all joints with tape and joint compound. Properly treat all corners and edges.

a. Joints and screw head dimples, flanges of corner bead and control joints, and all inside corners shall receive a three coat application of joint compound.

b. Subsequent coats of joint compound shall not be applied until the previous coat has dryed. Final coats shall be sanded so as to avoid unsightly joints. Caution shall be used to avoid roughing the wallboard paper.

c. Provide a minimum Level 4 finish at all surfaces that are to receive paint or wall covering.

d. Proper care shall be taken to minimize applying tape compound on adjacent finished surfaces. Clean daily all surfaces which may be soiled with compound.

5. Edge Finishing: Exposed gypsum wallboard edges which adjoin ceilings or meet walls of dissimilar materials shall be finished with metal trim pieces applied in true, straight lines.

6. Control Joints: Locate control joints where shown on the drawings. Provide seal behind control joints where located in fire rated walls or ceilings.


0924 - 1


0930 - 1

0930 Tiling


B. Scope: Furnish and install all ceramic porcelain, quarry, stone and paver tile floors and walls in accordance with ANSI specifications indicated and The Tile Council of America (TCA) Handbook for Ceramic Tile Installation, latest edition.

C. Materials:

1. Ceramic tile standard grade meeting ANSI 137.1. Size, color, finish, & price range group as indicated. Trim size, color and shade, finish, and thickness to match field tile unless otherwise indicated.

2. Quarry tile standard grade meeting ANSI 137.1. Size, color and finish as indicated. Trim size, color and shade, finish, and thickness to match field tile unless otherwise indicated. Bullnose exposed edges. Cove type base with round top at walls without quarry tile wall finish.

3. Paver tile meeting ANSI 137.1. Size, color, and finish as indicated. Trim size, color and shade, finish and thickness to match field tile unless otherwise indicated.

4. Setting Material: As recommended by TCA for specific application and location, and conforming to ANSI specifications.

5. Grout: As recommended by TCA and conforming to ANSI specifications. Color as selected by Architect.

6. Wall Tile: Latex Portland cement grout, unless otherwise indicated.

7. Floor Tile: Portland cement grout, unless otherwise indicated.

8. Quarry and Paver Tile: Acid resistant type grout, Hydroment, H.B. Fuller, or equal.

9. Terrazzo Divider Strip: "T" type or angle type, bronze, heavy duty.

10. Threshholds

a. General: Fabricate to sizes and profiles indicated or required to provide transition between adjacent floor finishes.

i. Bevel edges at 1:2 slope, with lower edge of bevel aligned with or up to 1/16 inch (1.5 mm) above adjacent floor surface. Finish bevel to match top surface of threshold. Limit height of threshold to ½ inch (12.7 mm) or less above adjacent floor surface.

b. Marble Thresholds: ASTM C 503/C 503M, with a minimum abrasion resistance of [10] [12] according to ASTM C 1353 or ASTM C 241/C 241M and with honed finish.


0930 - 2

i. Description: Uniform, fine- to medium-grained white stone with gray veining.

ii. Description: Match Architect’s sample.

11. Sealants: Polyurethane sealants, or approved equal, meeting Federal Specification TT-S-00227E, ASTMC920-79, as recommended by manufacturer for specific application. Color as selected.

12. Waterproof Membrane (if applicable): Manufacturer's standard product that complies with ANSI A118.10 and is recommended by the manufacturer for the application indicated. Include reinforcement and accessories recommended by manufacturer.

13. Crack Isolation Membrane (if applicable): Manufacturer's product that complies with ANSI A118.12 for and is recommended by the manufacturer for the application indicated. Include reinforcement and accessories recommended by manufacturer.

D. Workmanship

1. Examine the areas and conditions under which the work will be installed. Notify the contractor of conditions that will prevent satisfactory installation of the work. Do not proceed until conditions are corrected and acceptable. Determine locations of all movement joints before starting the work. All surfaces shall be examined, thoroughly cleaned and properly prepared to receive the tile work. Application of materials constitutes acceptance of the conditions and subcontractor accepts responsibility for adhesion of the tile work to the substrata and the proper location of expansion/control joints in the tile work.

2. Perform all work in accordance with TCA installation guides and methods, ANSI installation specifications, and material manufacturers recommendations. Tile shall be installed using thin set method unless otherwise indicated. Grout, protect, cure, and clean all work as specified and recommended by manufacturers.

3. Layout tilework to minimize cuts less than one half tile in size. Install tile true to line and dimension. Align wall joints to give straight uniform grout lines, plumb and level. Align floor joints to give straight uniform grout lines parallel with walls. Layout wainscots to next full tile beyond dimensions indicated. Locate tile cuts to be least conspicuous. Smooth all exposed cut tile edges. Fit tile carefully against trim and accessories, around pipes, electric boxes and other built in fixtures so that escutcheons and collars will completely overlap cut edges.

a. Install Terrazo divider strip at perimeter of entrance mats and carpet insert areas indicated by drawings. Properly anchor divider strip to sub-slab.

4. Provide expansion/control joints to accommodate movement in accordance with TCA recommendations. Caulk all expansion and control joints in the work with approved caulking materials in accordance with Specification Section 7.3 Caulking and Sealants. Verify layout of expansion joints with Contractor before proceeding with installation.


0930 - 3

5. After completion of grouting, remove all grout haze observing both tile and grout manufacturers recommendations as to use of chemical cleaners and acid, clean all work thoroughly with approved chemical cleaners, point open joints, and replace defective work. Rinse tile work thoroughly with clean water before and after chemical cleaners.

6. Protect all material to prevent damage during the progress of the work. Cure and protect the tile work in accordance with both the tile and grout manufacturers recommendations. Notify the contractor in writing as to any required curing conditions not present at time of start of work.

7. Furnish to the building site an extra 1% of each type of tile for future use.

E. Submittals:

1. Submit with bid proposal the following information:

a. Proposed TCA specification number to be followed for each location.

b. Tile manufacturer for each type.

2. Within 21 days of contract date, submit for approval the following:

a. Complete materials list of all items to be furnished with manufacturer's name, product type, etc., including mortar, tile, grout, caulking, etc.

b. Samples of finish and color range for all materials.

c. Sealant manufacturer's recommendations on use and installation of products.


0950 - 1

0950 Acoustical Ceilings


B. Scope:

1. Furnish all labor, skill, supervision, hoisting, handling, equipment, materials, etc., including suspension system design and layout, necessary to complete the installation of the suspended acoustical ceiling systems and acoustical wall treatment.

2. Suspension system structural capability and installation shall be in accordance with Uniform Building Code Standard No. 47-18, ASTM C635 & C636, and Texas Building Code Requirements. Minimum structural classification shall be intermediate duty systems. System shall safely support typical 2'x4' lay-in light fixtures indicated in Specification Section 16 Electrical, with a minimum capacity of 40 pounds each, with a factor of safety of 2.0 against load failure and vertical deflection not exceeding L/360 of span. Light fixtures shall be at random locations throughout the area with typical spacing as indicated.

C. Materials:

1. Acoustic Tile: Conform to Building Code and Fire Code requirements, Class A Federal specification SS-S-118B. Provide labeled tile for fire rated installations.

a. Act #1: 24"x48"x5/8" thick panels, standard factory painted white finish, mineral fiberboard, standard fissured pattern. Armstrong Dune 1774 or approved equal. See finish schedule on architectural plans.

2. Suspension System: Conform to Building Code and Fire Code Requirements. 24"x48" or 24"x24" exposed tee grid suspension system, factory painted white enamel finish, intermediate duty, Chicago Metallic Corporation Series 200 or 500 Snap-Grid System, or approved equal. Cross tees shall be #214 or #514, or approved equal.

a. Hanger wires minimum #12 gauge wire, or larger as required by loads or code requirements.

D. Workmanship:

1. Install acoustical tile ceiling system in accordance with manufacturer's recommendations, ASTM C636, and Building Code Requirements. Provide fire rated systems where indicated by the drawings. Provide all hangers, anchors, trim, edge moldings, etc. necessary for a complete installation.

2. Tile units shall be laid out symmetrically about centerlines of uninterrupted ceiling area. Use border units of maximum practical size. Coordinate layout and work with lighting, sprinkler, HVAC, etc., to assure that items located in the ceiling are located


0950 - 2

in an orderly manner with respect to tile units. All lines shall be straight and true. Complete ceilings shall be in true alignment and on a level plane.

3. Install suspension system main T's on 48" center spacing with hanger wire at 4'-0" maximum spacing. Support hangers from building structure only, with appropriate anchors or attachment. Suspension system shall not be supported from ductwork, piping, conduit, etc. Install cross T's at right angles to main T's and perimeter moldings locked into position. T's shall be straight in alignment and flush at intersections. Cut and support suspension system as necessary for special sizes and equipment which projects through the ceiling.

4. Provide and coordinate all necessary cuts, framing, and support for openings in the ceiling system.

5. Reveal edge ceiling tile shall be scored and cut a reveal edge at all edges of non-full size panels, and at both sides of partitions.

6. At building exterior perimeter walls not at right angles or parallel to ceiling grid system provide the necessary framing and support to accommodate air conditioning diffusers. Coordinate with mechanical subcontractor.

7. Deliver to jobsite and store in approved location 1% extra ceiling tile of each type used, minimum one full carton each, and one full carton of ceiling cross tees.

E. Submittals:

1. Submit for approval within 21 days of contract date the following:

2. Complete materials list of all items to be furnished with two (2) full size samples of each product type indicating manufacturer's name, product type, fire rating, etc., including hanger wire size for each system.

3. Suspension system manufacturer's specifications and data on load carrying capacity and rating of system.

4. Anchor manufacturer's data and load carrying capacity.


0964 - 1


0965 - 1

0965 Resilient Flooring and Base


B. Scope: Furnish and install all cork flooring, rubber flooring, sheet vinyl flooring, vinyl plank flooring, resilient flooring, and resilient base where scheduled.

C. Materials: Resilient flooring material shall be as manufactured by Armstrong, Azrock, Kentile, Tarkett-GAF, or equal. All materials shall be delivered to the jobsite in unopened cartons and shall be first quality. All materials shall be installed in areas as indicated on the plans and the Room Finish Schedule of the Drawings.

Adhesive: Adhesive shall be as recommended by manufacturers of the resilient materials. The proper adhesive selection for all installations shall be the responsibility of the resilient flooring Subcontractor.

D. Workmanship: All materials shall be stored in undamaged condition as packaged by the manufacturer, with seals and labels intact.

Surfaces to receive resilient flooring shall be dry, thoroughly clean and free of defects. Examine surfaces to receive the above materials and notify the Contractor of any condition that will prevent satisfactory results. All surfaces shall be examined, thoroughly cleaned and properly prepared to receive resilient flooring to be installed by the Subcontractor. Do not proceed until conditions are corrected. Application of materials signifies acceptance of such work and, therefore, this Subcontractor assumes responsibility of the final results.

Top-set cove base shall be installed wherever tile floor and wall joint is exposed to view. Firmly cement base to drywall. Internal and external corners may be job-formed.

Vinyl reducer strips shall be installed at all traffic areas where tile meets exposed concrete floor. Special care shall be taken when installing reducer strips to assure good adhesion.

Adhesive shall be mixed and applied in accordance with manufacturer's directions. Surface shall be covered evenly with adhesive. Area covered by one application of adhesive shall not exceed maximum working area recommended by manufacturer. Resilient flooring shall be installed within the time limits recommended by manufacturer.

Required curing conditions above those provided by the General Contractor shall be identified in writing by the Subcontractor to the General Contractor.


0965 - 2

Furnish 1% extra tile on the job for future use.

E. Submittals: Within 21 days of the subcontract date, submit the following for approval:

1. Product Data: For each type of product

2. Shop Drawings: For each type of linoleum flooring. Include flooring layouts, locations of seams, edges, columns, doorways, enclosing partitions, built-in furniture, cabinets, and cutouts.

a. Show details of special patterns

3. Samples: For each exposed product and for each color and pattern specified in manufacturer's standard size, but not less than 6-by-9-inch sections.

a. Heat-Welding Bead: Include manufacturer's standard-size Samples, but not less than 9 inches long, of each color required.

b. Base & Accessories: For each exposed product and for each color and texture, not less than 12 inches long.

4. Closeout Submittals: Maintenance data.


0968 - 1

0968 Carpet


B. Scope: Handle, hoist, and install all Carpet and furnish, deliver, handle, hoist, and install all Sheet Vinyl, Rubber Flooring, pad, trim, etc. as indicated on the Finish Drawings or as necessary to provide a complete installation. Installation labor, adhesive, and pad shall be in base bid proposal on lump sum basis.

C. Materials: All carpet shall be first quality and from the same dye lots for each different color. All materials shall be installed in areas as indicated on the plans and the Room Finish Schedule of the Interior Drawings. Color selections as indicated on the finish plans.

1. All carpet accessories shall be as per the Interior Finish Drawings.

2. All sheet vinyl material shall be as per the Interior Finish Drawings.

3. Adhesives shall be non-staining, waterproof, as recommended by carpet manufacturer.

D. Workmanship:

1. Carpet shall be neatly installed in accordance with manufacturer's recommendations and the best practice of the trade. The job shall be left clean of trash and scrap, however, the Owner shall view all carpet scraps and retain any he chooses for future repairs before they are removed from the site.

2. Extend carpet under open-bottomed and raised-bottom cabinets and/or equipment. Extend carpet into closets and alcoves of rooms indicated to be carpeted, unless other floor finishes are indicated for such places.

3. Install carpet edge strip at every location where edge of carpet is exposed to traffic, except where another device, such as an expansion joint cover or threshold is indicated with an integral carpet binder bar.

4. On stairs and stepped floor areas, install carpet by a secure method recognized to be durable and safe for traffic on stairs. Conceal edges and avoid placing seams at points of high wear.

5. Surfaces to receive carpet shall be dry, thoroughly clean and free of defects. Concrete floor surfaces shall be leveled to plus or minus 1/4" in 10 feet by this subcontractor. Any defects in the subfloor surface shall be corrected before starting carpet installation.

6. Adhesive shall be mixed and applied in accordance with manufacturer's recommendations.


0968 - 2

7. Carpet seams shall be clean, straight, and inconspicuous.

E. Submittals: Within 15 working days of award of contract submit for approval the following items for Contractor's review.

1. Shop Drawings: For carpet tile installation, plans showing the following:

a. Columns, doorways, enclosing walls or partitions, built-in cabinets, and locations where cutouts are required in carpet tiles.

b. Carpet tile type, color, and dye lot.

c. Type of subfloor.

d. Type of installation.

e. Pattern of installation.

f. Pattern type, location, and direction.

g. Pile direction.

h. Type, color, and location of insets and borders.

i. Type, color, and location of edge, transition, and other accessory strips.

j. Transition details to other flooring materials.

2. Samples: For each exposed product and for each color and texture required.

3. Informational Submittals

a. Product test reports.

b. Sample warranty.

4. Closeout Submittals

a. Maintenance data

5. Special Warranty

a. Special Warranty for Carpet: Manufacturer agrees to repair or replace components of carpet installation that fail in materials or workmanship within specified warranty period.


0990 - 1

0990 Painting and Wall Covering


B. Scope: Furnish and install all painting and wall covering work as indicated by the drawings and specified herein. Work includes, but is not limited to, the following:

1. Painting:

a. All exposed surfaces, including columns and structural members, as indicated by the drawings and finish schedule.

b. Interior exposed ferrous metals including but not limited to doors and frames, stairs, railings, metal trim, miscellaneous metals, etc.

c. Exterior exposed ferrous metals including but not limited to doors and frames, lintels, structural shapes, stairs, railings, bumper posts, louvers, miscellaneous metals, roof top equipment and other equipment indicated by drawings to be field painted.

d. Electrical panels, access panels, etc., located in finished walls or ceilings.

e. Parking lot striping, symbols, etc.

f. Stain, seal, and varnish wood doors, wood frames, trim, and millwork unless otherwise indicated.

2. Wall covering as indicated by drawings and finish schedule.

3. Interior columns shall receive finish as scheduled for walls of area in which columns are located.

4. Work shall conform with the Painting and Decorating Contractors of America Standards and Recommendations, Latest Edition, except where indicated otherwise by this specification.

5. Metal or wood surfaces with factory painted finish do not require field painting unless specifically noted to be painted in the Finish Schedule.

C. Materials:

1. All materials shall be commercial top-line products by reputable recognized Manufacturer delivered in unopened containers bearing Manufacturer's name.

a. Paint: By Benjamin Moore, Devoe, Fuller-O'Brien, Glidden, Pittsburgh Paint Co., Pratt & Lambert, Sherwin-Williams, or approved equal. All ingredients admixtures and vehicles used for on-site mixing shall conform to Manufacturer's Recommendations and ASTM Quality Standards.


0990 - 2

b. Wall Covering: As indicated by Room Finish Schedule.

c. Adhesive: As recommended by the manufacturer.

D. Workmanship:

1. Examine the areas and conditions under which the work will be installed. Notify the Contractor of conditions that will prevent satisfactory installation of the work. Do not proceed until conditions are corrected and acceptable. Examine, clean, and prepare all surfaces to receive the work. Application of materials constitutes acceptance of the conditions and subcontractor accepts responsibility for adhesion and appearance of the work.

2. Install all work in strict conformance with Material Manufacturer's printed instructions.

3. Remove or protect all hardware, light fixtures, electrical devices, cover plates, etc. and protect all adjacent surfaces.

4. Remove all rust, scale, or other foreign materials prior to painting. Treat all galvanized metal and concrete to be painted with a suitable clean degreasing and chemical naturalizing compound designed for this purpose before applying primer. Clean all other metal surfaces with mineral spirits before applying finish.

5. Spread all paint evenly without brush marks, laps, sags or other blemishes. All coats must be thoroughly dried before applying succeeding coats. Sand all wood work smooth between coats. Tint undercoating preceding final coat of enamel paint to the approximate shade of the final coat. Touch up knots, resinous streaks, spots, etc., in wood with shellac prior to applying second coat.

6. Finish all door edges including jambs, top and bottom. Fill all nail holes in wood with putty after sealer coat and prior to varnishing.

7. Touch up prime paint on surfaces with factory or shop applied prime coats prior to finish field painting.

8. Additional coats of paint required to provide uniform color or to cover defects shall be provided at subcontractors sole cost and expense.

9. Size all gypsum board before applying wall coverings. Clean all adhesive from wall covering in accordance with Manufacturer's Recommendations.

10. Store all materials in one location where directed by Contractor. No benzine, naphtha, or gasoline will be allowed on the premises. Store painters work clothing, rags, etc., in approved cans with tight lids when not in use. All cans of paint and thinning liquids shall be stored in a similar approved case or in metal lockers outside of the building. Maintain a fire extinguisher in paint storage area. Conform to all safety standards in the storage and handling of materials.

E. Finished Color Schedule:


0990 - 3

1. A finish color schedule for the work will be provided by the Contractor. All paint and wallcovering shall be in accordance with the finish color schedule.

F. Paint Schedule:

1. Location /Substrate

a. Galvanized Metal

i. Materials: Solvent acrylic primer, or approved equal.

Coats: 1

ii. Materials: Alkyd gloss enamel.

Coats: 2

b. Exterior Metal (ferrous)

i. Materials: Rust inhibitive primer, 1 mil dft.

Coats: 1

ii. Materials: Alkyd gloss enamel

Coats: 2

c. Exterior Wood (painted)

i. Materials: Primer (exterior oil base).

Coats: 1


Coats: 2

d. Exterior Wood (stained)

i. Materials: Flat alkyd stain (opaque).

Coats: 2

e. Exterior Concrete Block, Concrete, or Precast Concrete

i. Materials: 100% acrylic masonry paint.

Coats: 2

f. Interior Concrete Block or Interior Precast Concrete


0990 - 4

i. Materials: Vinyl Acrylic Latex primer

Coats: 1

ii. Materials: Latex flat

Coats: 1

g. Gypsum Wall Board

i. Materials: Vinyl Acrylic Latex primer

Coats: 1

ii. Materials: Satin latex enamel

Coats: 1

h. Interior Exposed Ferrous Metals Located Below Bottom of Overhead Structural Support for Roof or Floor Deck.

i. Materials: Rust inhibitive primer.

Coats: 1

ii. Materials: Alkyd semi-gloss enamel.

Coats: 2

i. Interior Exposed Steel Roof or Floor Deck including Deck Structural Support Beams, Joists, Girders, etc. Columns shall be painted per paragraph 8 above.

i. Materials: Alkyd dry fog flat.

Coats: 1

j. Interior Exposed Softwood

i. Materials: Alkyd enamel undercoat.

Coats: 1

ii. Materials: Alkyd semi-gloss enamel.

Coats: 2

k. Interior Hardwood and Millwork

i. Materials: Penetrating oil stain.

Coats: 1


0990 - 5

ii. Materials: Sealer.

Coats: 1

iii. Materials: Satin varnish.

Coats: 1

l. Epoxy Wall Finish

i. Materials: Primer for specific surface

Coats: 1

ii. Materials: Epoxy coating

Coats: 1

m. Parking Lot Striping

i. Materials: White or yellow traffic paint.

Coats: 1

n. Aluminum (untreated)

i. Materials: Two part acid catalyzed vinyl washcoat pretreatment type primer, or as recommended by paint Manufacturer.

Coats: 1


Coats: 2

G. Submittals:

1. Within 21 days of contract date submit for approval the following:

a. Complete materials list of all items to be furnished with Manufacturer's name, and product type.

b. Product Specification Data and Manufacturers Installation Recommendations.

c. Samples of finish and color for all materials.

H. Unit Price:


0990 - 6

1. Submit unit price ($ /s.f.) to add or deduct each of the paint and wallcovering items indicated by the finish schedule.

2. Submit unit prices ($ /ea) to add or deduct finish on the following items:

a. H.M. Door

b. H.M. Frame

c. Wood Door

d. Wood Frame

ODB Master - Division 10 - Specialties (06/20/16)

1014 - 1

1000 - SPECIALTIES

1014 Signage


B. Scope:

1. Provide all design, engineering, drawings, services, skill, labor, material, layout, equipment, handling, and hoisting, necessary for a complete installation of all signage as shown on the plans and specified herein.

C. Materials:

1. Accessibility Compliance: All signs are required to comply with ADA Standards for Accessible Design and ANSI/ICC A 117.1 and applicable building codes, unless otherwise indicated; in the event of conflicting requirements, comply with the most comprehensive and specific requirements.

2. Room and Door Signs:

a. Sign Type: Flat signs with engraved panel media as specified.

b. For dwelling units provide sign for corridor entry door only; no signs required for subsequent rooms inside.

c. Provide "tactile" signage, with letters raised minimum 1/32 inch and Grade II braille.

d. Character Height: 1 inch.

e. Border Dimension of Pictograms: 6 inch minimum.

f. Dwelling Unit Doors: Identify with room numbers to be determined later, not the numbers shown on the drawings.

g. Service Rooms: Identify with room names to be determined later.

h. Rest Rooms: Identify with pictograms, the names "MEN" and "WOMEN", and braille.

i. Stairs (Corridor/Room Side): Provide a 12 x 20 inch sign; identify with stair name/number to be determined later, other messages indicated below, and with two "window" sections, one for inserting a floor plan showing the area of refuge locations and one for all instructions required. Additional messages:

i. Stairs Including an Area of Refuge: Include messages "EXIT", "AREA OF REFUGE", and international symbol of accessibility.


1014 - 2

ii. Stairs Not Including an Area of Refuge: Include messages "EXIT" and "NOT AN AREA OF REFUGE".

iii. Areas of Refuge:

1) Provide sign containing instructions addressing the following:

a. Directions to find other means of egress.

b. Persons able to use the exit stairway do so as soon as possible, unless they are assisting others.

c. Information on planned availability of assistance in the use of stairs or supervised operation of elevators and how to summon such assistance.

d. Directions for use of the emergency communications systems.

2) Locate at each area of refuge containing 2-way communication systems.

3. Interior Directional and Informational Signs:

a. Sign Type: Same as room and door signs.

b. Directional Signs:

i. Provide directional sign that has 2 lines of text, each of which will read "### - ###" with directional arrow.

ii. For floors having dwelling units, provide one per floor per elevator bank; numbers to read and arrows to point as indicated by Architect.

c. Elevator Signs:

i. Provide 9 x 9 inch signs with text message, braille, and pictograms: "IN CASE OF FIRE USE EXITS"; verify actual text message and required pictograms with Authority Having Jurisdiction (AHJ).

d. Stair Identification Signs (Stair Enclosure Side):

i. Provide 12 x 12 inch signs with text size, position, and content conforming to applicable Building Code requirements; indicate stair location or name, floor level, roof access or not, direction to the exit discharge, and termini.

ii. Locate at each floor level of each stair with centerline of sign 5'-0" above landing floor in a position that is readily visible with the door in either the open or closed position; verify proposed location with the AHJ.


1014 - 3

e. Occupant Load Signs for Assembly Occupancies:

i. Text message only, indicating occupant load and concentrated use occupant load.

4. Provide one raised letter sign for each assembly space. Size as required for message; 5/8 inch high text. Locate as directed by AHJ.

5. Traffic Signs: Use symbols recognized by the Federal Highway Administration and conform to applicable municipal standards; manufacture signs from 16 gage aluminum sheet with reflective coating.

a. Provide one 12 x 18 inch restricted parking sign for each accessible parking stall. Include all messages required by AHJ. At 8-foot wide van accessible access aisles, provide one.

6. 12 x 18 inch sign which states: "ACCESS AISLE, NO PARKING."

a. Provide "STOP" signs at each driveway entrance to public street or road. Size as required by AHJ.

b. Provide one 12 x 8 inch sign indicating "COMPACT STALL" for each such stall.

c. Provide overhead suspended headroom control signs in parking garage, in vicinity of accessible parking stalls; restrict access to areas where clear height is less than 8'-2" above finish floor.

d. Provide chain or cable supported sheet metal or large diameter PVC pipe "message board", painted finish, with vinyl die-cut adhesive-backed characters for messages.

7. Internally Illuminated Signs

a. Comply with applicable provisions of ADA Standards for Accessible Design, ANSI/ICC A 117.1, and applicable building codes, for signs not required to be tactile.

b. Type: Internally illuminated, single or double face message as required, exterior mounted, one face removable.

c. Thickness: As required by internal components and construction.

d. Faces: Aluminum sheet, 0.090 inch thick.

e. Message: Router or water jet cut face with back mounted translucent acrylic lens.

f. Case Frame and Reinforcing: Extruded aluminum channels and angles of size required for use.

g. Internal Illumination: LED lamps; 120 V, single phase. Pre-wire sign case for single point connection in field.


1014 - 4

h. Exterior Finish: Paint; color as selected.

D. Workmanship:

1. Package signs as required to prevent damage before installation.

2. Package room and door signs in sequential order of installation, labeled by floor or building.

3. Examine the areas and conditions under which work will be installed. Do not proceed until unsatisfactory conditions have been corrected.

4. Install in accordance with manufacturer's instructions.

5. Install signs after surfaces are finished.

6. Install neatly, with horizontal edges level.

7. Locate signs where indicated:

a. Room and Door Signs: Locate on wall at latch side of door with centerline of sign at 60 inches above finished floor.

i. At pairs of doors, locate signs on the wall to right of right door leaf, with centerline of sign at 60 inches above finished floor.

ii. Locate signs so a person may approach within 3 inches of signage without encountering protruding objects or standing within swing of door.

iii. Request direction at doors where wall surface is not of sufficient size to receive sign.

b. If no location is indicated obtain Owner's instructions.

8. Install individual graphics level, unless otherwise indicated, with characters uniformly and consistently spaced.

9. Install traffic control signs:

a. At exterior locations, mount signs on steel post.

b. At interior locations, mount directly on concrete or masonry walls or mount from overhead.

10. Protect from damage until Substantial Completion; repair or replace damage items.

E. Submittals:



1014 - 5

a. System manufacturer.

b. Specifically identify all deviations or qualifications to the contract documents.

2. Product Data: Manufacturer's printed product literature for each type of sign, indicating sign styles, font, foreground and background colors, locations, overall dimensions of each sign.

3. Signage Schedule: Provide information sufficient to completely define each sign for fabrication, including room number, room name, other text to be applied, sign and letter sizes, fonts, and colors.

a. When room numbers to appear on signs differ from those on the drawings, include the drawing room number on schedule.

b. When content of signs is indicated to be determined later, request such information from Owner through Architect at least 2 months prior to start of fabrication; upon request, submit preliminary schedule.

c. Submit for approval by Owner through Architect prior to fabrication.

4. Samples: Submit two samples of each type of sign, of size similar to that required for project, illustrating sign style, font, and method of attachment.

5. Selection Samples: Where colors are not specified, submit two sets of color selection charts or chips.

6. Verification Samples: Submit samples showing colors selected for use.

7. Manufacturer's Installation Instructions: Include installation templates and attachment devices.


1021 - 1

1021 Toilet Partitions


B. Scope:

1. Provide all design, engineering, drawings, services, skill, labor, material, layout, equipment, handling, and hoisting, necessary for a complete installation of all toilet partitions and urinal screens in the toilet rooms as shown on the plans and specified herein.

C. Materials:

1. Metal Partitions:

a. All metal partitions shall be ceiling hung and equal to those manufactured by Accurate Partitions, Inc., Metpar/Sanymetal Products, Bobrick, Bradley Corporation, All American Metal Corp, Hadrian manufacturing Inc., Marlire or approved equal, in baked enamel finish of color selected from the manufacturer's standard range. Urinal screen style shall be wall hung. There shall be a minimum selection of ten colors. Partitions shall be of the lengths and widths as shown on plans.

2. All toilet partitions shall be complete with chromed latch, coat hooks, and rubber bumpers and shall conform to the provisions for the handicapped where shown on the drawings, including having sufficient and properly located reinforcing built into partitions to accommodate required grab bars furnished under section l028.

3. All toilet partitions shall meet or exceed the following surface-burning characteristics when tested in accordance with ASTM E84:

a. Flame-Spread Index: 25 or less

b. Smoke-Developed Index: 450 or less

D. Workmanship:


2. Comply with manufacturer’s written installation instructions. Install units rigid, straight, level, and plumb. Secure in position with manufacturer’s recommended anchoring devices.

3. Adjust and lubricate hardware according to hardware manufacturer’s written instructions for proper operation. Set hinges on in-swinging doors to hold doors open approximately 30 degrees from closed position when unlatched. Set hinges on out-swinging doors to return doors to fully closed position.


1021 - 2

E. Submittals:


a. System manufacturer and model number.



a. Complete materials list of all items to be furnished


c. Manufacturer's Published Literature that systems conform to specified standards.

d. Shop drawings in electronic pdf file format. Shop drawings shall include:

i. Load reactions at attachment points. Blocking and support in walls and above ceilings shall be by others.

ii. Locations of reinforcements for compartment-mounted grab bars.

iii. Locations of centerlines of toilet fixtures

e. Manufacturer's Recommendations on installation of systems.

F. Warranty:

1. Furnish manufacturer's standard written warranty


1022 - 1

1022 Operable Partitions


B. Scope:

1. Provide all design, engineering, drawings, services, skill, labor, material, layout, equipment, handling, and hoisting, necessary for a complete installation of all operable partitions and suspension systems as shown on the plans and specified herein.

C. Materials:

1. Paired Panel <or Continuously hinged>, manually (or motor) operable partitions equal to Hufcor 600 Series, or Moderco 8000 Series. Panel finish shall consist of manufacturer’s standard color upgrade fabric applied over Class A rated gypsum. Panels shall have top seals and retractable bottom seals. Frame and trim color shall be of manufacturer’s standard colors. Color shall be selected during submittal phase.

2. Pass Doors: Included fabricated swinging doors where shown on the plans. Doors shall be built into and matching panel materials, construction, acoustical qualities, finish, and thickness, complete with frames and operating hardware.

3. Acoustical Performance:

a. Sound Transmission Class of 50 or higher when tested according to ASTM E 90 and classified per ASTM E 413.

b. Noise Reduction Coefficient of 0.4 or higher when tested according to ASTM C 423.

4. All partitions shall meet or exceed the following surface-burning characteristics when tested in accordance with ASTM E84:

a. Flame-Spread Index: 25 or less

b. Smoke-Developed Index: 450 or less

D. Workmanship:


2. Comply with manufacturer’s written installation instructions and approved drawings. Install rigid, straight, level, and plumb. Secure in position with manufacturer’s recommended anchoring devices.


1022 - 2

3. Adjust operable panel partitions to operate smoothly, easily, and quietly, free from binding, warp, excessive deflection, distortion, non-alignment, or malfunction throughout the entire operational range. Lubricate hardware and other moving parts.

4. Conduct one (1) operations and maintenance training session with building representatives upon completion of the project. Schedule the training session with the Opus project manager

E. Submittals:



b. System STC and NRC values

c. Specifically identify all deviations or qualifications to the contract documents.

d. Alternate prices for all alternates specified herein.



b. Three (3) sets of fabric selection charts

c. Shop drawings; Six (6) sets of paper and one (1) copy in electronic pdf file format. Shop drawings shall include:

i. Load reactions at attachment points of overhead support beam

ii. Template of attachment points to overhead support beam

iii. Deflection limits of overhead support structure

d. Manufacturer's recommendations on installation of systems.

F. Miscellaneous

1. Furnish Manufacturer's Standard Written Warranty

2. Alternates:

a. Design, furnish, and install overhead support beam. Include attachment to building structure, or new steel posts, as applicable.


1026 - 1

1026 Corner Guard


B. Scope:

1. Provide all design, engineering, drawings, services, skill, labor, material, layout, equipment, handling, and hoisting, necessary for a complete installation of all corner guards as shown on the plans and specified herein.

C. Materials:

1. Corner Guards:

a. Inpro

b. Construction Specialties, Inc.

c. Or approved equal

D. Workmanship:


2. Comply with manufacturer’s written installation instructions. Secure in position with manufacturer’s recommended anchoring devices.

3. Protection: Take all necessary steps to prevent damage to material during installation as required in manufacturer’s installation instructions.

4. Code compliance: Assemblies should conform to all applicable codes including IBC, UBC, SBCCI, BOCA and Life Safety.

E. Submittals:





a. Complete materials list and detailed specifications of all items to be furnished


1026 - 2


c. Shop drawings in electronic pdf file format. Shop drawings shall include:

i. Product test reports from a qualified independent testing laboratory showing compliance with each component with requirements indicated.

ii. Maintenance data for wall protection systems.


1028 - 1

1028 Toilet Accessories


B. Scope:

1. Furnish two (2) paper towel cabinet for each toilet room.

2. Furnish one (1) sanitary napkin disposal for each women's/unisex toilet stall.

3. Furnish grab bars for handicapped in toilet rooms where noted on drawings

C. Materials:

1. Towel Dispensers: Towel dispensers shall be equal to Bobrick B3956 semi-recessed universal cloth and paper towel dispenser cabinet and waste receptacle without towel dispensing mechanism.

2. Grab Bars: Grab bars shall be equal to those manufactured by Bobrick and in conformance with all applicable codes.

3. Sanitary Napkin Disposal Unit: Units shall be equal to Bobrick B27O.

4. The finish on all exposed surfaces is to be No. 4 satin.

D. Workmanship:

1. Furnish all templates, fastening devices, etc. as required for a neat, craftsmanlike installation by others.

E. Submittals:






b. Catalog cuts of each item to be furnished in electronic pdf file format.

c. Manufacturer's instructions on installation of materials.


1028 - 2

F. Warranty:

1. Furnish Manufacturer's Standard Written Warranty


1044 - 1

1044 Fire Extinguishers and Cabinets


B. Scope: Provide fire extinguisher cabinets and extinguishers as indicated on the drawings and specified herein.

C. Materials:

1. Semi-recessed fire extinguisher cabinets shall be equal to J.L. Industries Ambassador model 1017S21 <or 1017V10 for vertical glass door>, with white powder coated finish. Provide fire-rated cabinets as required within fire-rated assemblies.

a. <1. Semi-recessed fire extinguisher cabinets shall be equal to J.L. Industries Cosmopolitan model 1037S21 <or 1037V10 for vertical glass door>, with #4 stainless steel finish. Provide fire-rated cabinets as required within fire-rated assemblies.>

b. <1. Semi-recessed fire extinguisher cabinets shall be equal to J.L. Industries Academy model 1027S21 <or 1027V10 for vertical glass door>, with clear anodized aluminum finish. Provide fire-rated cabinets as required within fire-rated assemblies.>

2. Fire extinguishers shall be equal to J.L. Industries Cosmic 10E with a 4A-80BC UL rating, and shall be properly tagged/inspected as required by code officials.

D. Submittals:


a. Manufacturer and model number.



a. Complete materials list of all items to be furnished.

b. Product cut sheets in electronic pdf file format.

c. Manufacturer's instructions on installation.


1051 - 1

1051 Metal Lockers/Benches


B. Scope: Furnish and install metal lockers/benches as indicated on the drawings and as specified herein.

C. Materials:

1. Manufacturers: Penco, Republic, Lyon, or equal.

2. Type: Standard metal lockers with number plates, standard interiors, "Z" metal base, and sloped tops. Quantity as indicated on drawings.

3. Double-tier lockers: 12"W x 18"D x 36"H (x2 levels) standard metal lockers with number plates, standard interiors, "Z" metal base, and sloped tops. Quantity as indicated on the drawings.

4. Bench: 72” x 9-1/2” x 18” high maple bench with painted steel pedestals. Quantity as indicated on the drawings.

5. Color: As selected by Architect from manufacturer’s standard colors.

D. Workmanship: Lockers and benches must be installed in accordance with manufacturer's approved drawings and assembly instructions. Installation shall be level and plumb with flush surfaces and rigid attachment to anchoring surfaces. Space fasteners at 36'' O.C. or less as recommended by manufacturer. Use fasteners appropriate to load and anchoring substratum. Use reinforcing plates wherever fasteners could distort metal. Various trim accessories where shown such as sloping tops, fillers, bases, recessed trim, etc., shall be installed using concealed fasteners. Flush, hairline joints are provided at all abutting trim parts and at adjoining surfaces. Upon completion of installation, inspect lockers and adjust as necessary for proper door and locking mechanism operation. Touch up scratches and abrasions to match original finish.

E. Submittals:


a. Manufacturer and model number.



a. Complete materials list of all items to be furnished.


1051 - 2

b. Product cut sheets in electronic pdf file format.

c. Manufacturer's instructions on installation.

d. Samples of finish and color range for all materials.

F. Warranty:

1. Furnish manufacturer's standard written warranty.


1055 - 1

1055 Postal Specialties


B. Scope:

1. Provide all design, engineering, drawings, services, skill, labor, material, layout, equipment, handling, and hoisting, necessary for a complete installation of all postal specialties as shown on the plans and specified herein.

C. Materials:

1. Mail Boxes:

a. Auth-Florence Manufacturing Company: www.authflorence.com.

b. Bommer Industries, Inc.: www.bommer.com.

c. Postal Products Unlimited, Inc.: www.mailproducts.com.

d. Salsbury Industries: www.mailboxes.com.

e. Security Manufacturing Corp: www.securitymanufacturing.com.

f. Or approved equal

2. All mail boxes served by the U.S. postal service must comply with U.S. Postal Service Standard 4C.

3. Components:

a. Front Loading Panel Frame:

b. Aluminum with color anodized finish; color as selected by Architect.

c. Edges beveled, piano hinged jamb, prepared for Post Office lock cylinder.

d. Box Door: Aluminum with finish to match frame.

e. In each door face, engrave and paint black a 3 digit numeral corresponding to each dwelling unit number.

f. Edges beveled, piano hinged jamb, prepared for lock cylinder.

g. Box Construction: Sheet steel, zinc coated, 22 gage thick, fabricated into modular stackable units, baked enamel flat black finish. Pre-punch bolt holes in box for stack bolting to each other and anchoring to adjacent construction.

http://www.authflorence.com/

http://www.bommer.com/

http://www.mailproducts.com/

http://www.mailboxes.com/

http://www.securitymanufacturing.com/


1055 - 2

h. Front loading, horizontal mailboxes with integral directory and mail drop.

i. Box Sizes: Configured as follows: Size: 3 x 12 x 15 inches (H x W x D).

j. Postal Box Locks: USPS standard, two keys per box.

k. "Out-Going Mail" Lock Box and Box Access: Face plate to match front loading panel frame, box of galvanized steel construction, lockable with cylinder provided by Post Office.

l. Include one box for each dwelling unit and one double box for office.

m. Include parcel lockers; provide:

i. At a ratio of 1 parcel locker for every 10, or fraction thereof, of resident lockers.

ii. A minimum of 2 parcel lockers.

D. Workmanship:


2. Comply with manufacturer’s written installation instructions and U.S. Postal Service regulations.

3. Ensure that:

a. At least 2 resident lockers are positioned less than 48 inches above finished floor.

b. No parcel locker interior bottom shelf is positioned less than 15 inches above finished floor.

c. No resident locker lock is located more than 67 inches above finished floor.

d. Outgoing mail slot is located between 36 and 48 inches above finished floor.

e. USPS Arrow lock is located between 36 and 48 inches above finished floor.

4. Install and secure boxes in position, neatly, and accurately stacked.

5. Install doors and adjust to operate smoothly.

E. Submittals:




1055 - 3



a. Product Data: Provide data for components


c. Shop drawings in electronic pdf file format. Shop drawings shall include:

i. Indicate locations, construction and anchorage details, dimensions, rough-in opening sizes, quantity and arrangement of box sizes.


1056 - 1

1056 Metal Storage Shelving


B. Scope:

1. Furnish and install metal shelving as indicated on the drawings and as specified herein. Metal shelving shall have 500 lb capacity per shelf and 2,000 lb capacity per shelf at pallet racks.

C. Materials:

1. Metal Storage Shelving Manufacturers:

a. Lyon Metal Products, Inc.: Style: 8000 Series Heavy Duty Industrial Shelving

b. Penco Products, Inc.: Style: Heavy Duty Clipper Shelving

c. Tennsco: Style – Industrial Clip type shelving

d. or approved equal.

2. Metal Storage Shelving Components:

a. Posts:

i. Configuration: Box shaped; slotted for 1 inch or 1 ½ inch vertical adjustment.

ii. Material: 14 gage hot rolled, formed steel

iii. Size: 1 ¾ x 1 ¾ inch (nominal); overall height is 84 inches (minimum)

iv. Finish:

1) Baked enamel finish (u.n.o.)

b. Side Panels, top and backs:

i. Configuration: flat panels; one piece

ii. Material: 14 gage hot rolled, formed steel

iii. Size: 1 ¾ x 1 ¾ inch (nominal); height is same as posts.

iv. Finish:


1056 - 2

1) Baked enamel finish (u.n.o.)

3. Shelves:

a. Configuration: adjustable flat panel, heavy duty with front and rear box formation for even distribution of loading

b. Material: 20 gage hot rolled, formed steel (minimum)

c. Size: 12 x 48, 24 x 36 inches, 24 x 48 inches (nominal)

d. Finish:

i. Baked enamel finish (u.n.o.)

ii. Quantity: Typical unit - 5 per vertical unit

4. Braces:

a. Configuration: manufacturer’s standard shape

b. Material: 12 gage, formed steel

c. Finish:

i. Baked enamel finish. (u.n.o.)

5. Pallet Rack Shelving Manufacturers:

a. Folding Guard Company: Style - Galvanized Wire Pallet Decking

b. Penco Products, Inc.: Style - Pallet Rack

c. Boston Rack & Wire: Style – Interlake Pallet Rack

d. or approved equal.

6. Pallet Rack Shelving Components:

a. Upright Frames:

i. Configuration: Continuous posts - M shaped; welded into rigid unit; slotted for 3 inch vertical adjustment.

ii. Material: formed steel

iii. Size: 42 depth; overall height is 84 inches (minimum)

iv. Finish: Baked enamel (u.n.o.)

b. Shelves:


1056 - 3

i. Configuration: adjustable wire panel, heavy duty with 14 gage channel supports; accommodate 1 5/8 inch step down beams

ii. Material: 4 gage; wire construction with 2 x 4 mesh (minimum)

iii. Size: 42 x 96 inches (nominal)

iv. Finish: galvanized.

v. Quantity: Typical unit - 4 per vertical unit

c. Beams:

i. Configuration: roll-formed one piece; 1 5/8 inch step down; end connectors with three prong connection and tabs

ii. Material: extra heavy gage formed steel

iii. Finish: baked enamel (u.n.o.)

d. Braces: channel type; MIG welded together with upright frame.

e. Foot Plate: galvanized; heavy gage welded to each post with two holes for floor anchoring.

7. Accessories:

a. Metal shelving:

i. Shelf clips: 12 gage; cadmium plated or zinc plated steel

ii. Wall and floor brackets: manufacturer’s standard component.

iii. Post Caps: manufacturer’s standard component.

b. Pallet Rack Shelving:

i. Frame protector: manufacturer’s standard component.

ii. Rigid Row Spacer: manufacturer’s standard component to connect two rows of rack back to back; bolted type

iii. Rigid wall brackets: manufacturer’s standard component

iv. Fasteners: anchor suitable for substrate encountered

c. Shop and Touch-Up Primer: SSPC 15, Type 1, red oxide

d. Touch-Up Primer for Galvanized Surfaces: SSPC 20 Type I Inorganic zinc rich


1056 - 4

D. Workmanship:

1. Fabrication:

a. Fit and assemble in largest practical sections for delivery to site, ready for installation.

b. Make exposed joints flush or tight.

c. Furnish components required for anchorage to adjacent construction.

d. Provide support posts at each corner of shelves.

e. Fabricate assemblies to be adjustable without disassembly of entire shelf unit.

f. Fabricate closed assemblies to accommodate side, back and top enclosure panels for each shelf unit.

g. Provide all necessary clips, fasteners, braces and other items required to make units complete, usable, and rigid.

h. Provide wall anchors for all shelving; minimum of 2 anchors each side of each set of shelves

2. Shop Finishing:

a. Clean surfaces of rust, scale, grease, and foreign matter prior to finishing.

b. Shop Finish all components, unless noted as galvanized.

3. Execution:

a. Examination: Verify substrate surfaces and required openings are ready to receive work.

b. Preparation: Clean substrate surfaces.

c. Installation:

i. Install items plumb and level, accurately fitted, free from distortion or defects. Set shelving components square, securely anchored to substrate. Anchor rows or runs of shelving to building using anchoring devices to suit conditions and substrate materials encountered.

ii. Install shelving components at locations indicated, in continuous runs comprised of a series of shelving units as indicated. Comply with manufacturer’s recommendations for assembly connections.

iii. Adjust shelving units to true level. Verify with Owner if shelves are to be assembled in equal spacing or in special arrangements.


1056 - 5

iv. After installation, field touch-up scratched or damaged surfaces with shop applied primer and finish.

v. Repair or replace any component damaged prior to final acceptance.

d. Protection of Installed Construction:

i. Protect against damage from adjacent traffic and construction activities. Do no permit shelving to be exposed to continued construction activities or used for storage of construction materials.

e. Erection Tolerances:

i. Maximum variation from plumb or level: 1/8 inch

ii. Maximum misalignment from indicated position: 1/8 inch

E. Submittals:





a. Samples of finish and color range for all materials.

b. Contractor to submit a metal shelving schedule for each room. Provide room number, shelving unit size and quantity for each type of shelving.

c. Contractor to submit a pallet rack schedule for each room. Provide room number, shelving unit size and quantity of each type shelving.


1075 - 1

1075 Flagpoles


B. Scope: Provide all design, engineering, drawings, services, skill, labor, material, layout, equipment, handling, and hoisting, necessary for a complete installation of all flagpoles as shown on the plans and specified herein.

C. Materials:

1. Aluminum Flagpole:

a. Fabricate from seamless, extruded tubing complying with ASTM B 221, alloy 6063-T6, having a tensile strength not less than 30,000 psi with yield point of 25000 psi. Heat treated after fabrication to comply with ASTM B 597, temper T-6.

b. External halyard system.

c. Finish to be selected from manufacturers standard colors.

D. Workmanship:

1. Do not begin installation until final grades and elevations have been established.

2. Comply with manufacturer’s written installation instructions.

3. Store products in manufacturer's unopened packaging until ready for installation.

4. Structural Performance: Provide flagpole assemblies, including anchorages and supports, capable of withstanding the effects of wind loads.

E. Submittals:


a. Manufacturer’s data sheets on each product to be used, including:

i. Preparation instructions and recommendations

ii. Storage and handling requirements and recommendations

iii. Installation instructions



1075 - 2


a. Samples of finish and color range for all materials.

b. Shop drawings in electronic pdf file format. Shop drawings shall include engineered details of foundation system

ODB Master - Division 12 – Furnishings (06/20/16)

1221 - 1

1200 - FURNISHINGS

1221 Aluminum Blinds


B. Scope: Furnish and install aluminum window blinds on exterior windows. One blind shall be provided at each window. Do not furnish window blinds at interior or exterior vestibule glass or doors at the building entrances.

C. Material: Window blinds shall be Levelor Riviera, Bali, Hunter-Douglas, or approved equal. The blind shall have nominally one inch wide horizontal slats complete with head channel, tilter, cordlock, drums and cradles, tilt rod, and brace, installation brackets, slat supports, bottom rail, lift cord, and all other components and accessories necessary for a complete installation. All blinds shall have limited tilt feature and optional ring pull feature. Color to be a matt finish in a color selected by the Architect from manufacturer’s standard colors.

D. Workmanship: Subcontractor shall verify and field measure all dimensions prior to fabrication. Blinds shall be installed between the vertical window mullions with brackets mounted to the mullions in accordance with manufacturer’s written instructions. Blinds shall be installed level and plumb, aligned and centered on openings, and aligned with adjacent units according to manufacturer's written instructions. Coordinate installation with glass subcontractor and follow glass subcontractor's recommendations to prevent damage to glass due to heat build-up between glass and blinds, and to prevent damage to the aluminum framing systems. All blinds in future tenant areas that are not yet built out shall be installed in protective bags to prevent dust accumulation.

E. Submittals: Within ten days of contract date submit two (2) sets of manufacturer's standard color/pattern charts for selection by Architect. Submit five (5) sets of manufacturer's specifications and installation instructions for each type of window blind. Include methods of installation for each type of opening and supporting structure.


1224 - 1

1224 Roller Shades


B. Scope: Furnish and install fabric roller shades where shown on the plans.

C. Material: Window blinds shall be Draper Shade System or approved equal. Color to be selected by the Architect from manufacturer’s standard colors.

D. Workmanship: Subcontractor shall verify and field measure all dimensions prior to fabrication. Roller shades shall be installed between the vertical window mullions with brackets mounted to the mullions in accordance with manufacturer’s written instructions. Install roller shades level, plumb, and aligned with adjacent units, according to manufacturer's written instructions. Coordinate installation with glass subcontractor and follow glass subcontractor's recommendations to prevent damage to glass due to heat build-up between glass and blinds, and to prevent damage to the aluminum framing systems. Adjust and balance roller shades to operate smoothly, easily, safely, and free from binding or malfunction throughout entire operational range. Clean roller-shade surfaces after installation, according to manufacturer's written instructions.

E. Submittals: Within 4 days of award of contract submit two (2) sets of manufacturer's standard color/pattern charts for selection by the Architect. Submit two (2) sets of manufacturer's specifications and installation instructions for each type of window blind. Include methods of installation for each type of opening and supporting structure.


1261 - 1

1248 Entrance Mats and Frames


B. Scope: Furnish entrance mats and accessories in sizes and quantities indicated on the drawings.

C. Materials: Entrance mats shall be Rugged Scrub as manufactured by Arden Architectural Specialties, C/S Group Duration series, Interface Graphlar Tile, Lees Step Up Modular or approved equal.

Provide frame manufactured from 6063-T52 aluminum as supplied by the approved supplier. Finish shall be clear anodized or as selected by the Architect. Floor mat surface shall be broadloom carpet bonded to substrate and framed by aluminum frame. Color of entrance mat shall as selected by the Architect from manufacturer’s standard colors.

D. Workmanship: Verify and field measure mat dimensions prior to fabrication. Coordinate the top of mat or frame surfaces with doors that swing across the area, to provide under door clearance. Where joints in mats are necessary, space symmetrically and away from normal traffic lanes. Miter corner joints in framing elements with hairline joints or provide prefabricated corner units without joints.

E. Submittals: Submit five (5) sets of shop drawings and catalog cuts indicating quantity, sizes, and manufacturer's installation instructions. Submit two (2) 12x12 samples each of standard frame/rail and carpet colors.