I d i h R li6 0 iSubstation Automation ProductsIntroduction to
the Relion670 series Hardware Hardware SA-T Training1MRG004718
Section 03Contents Hardware - General HardwareGeneral Hardware
configuration Modules Hardware overview Local HMI Summary Hardware
modulesCommunication Communication Time synchronization SA-T
Training1MRG004718Slide 2Section 03Relion670 series Hardware
general Platform based Platform based Closed casings of common look
HMI unit with Ethernet PC port Small or medium size Small or medium
size graphical display Common modules Easy future hardware
additionypossibilities Dimension 1/2, 3/4 or 1/1 of 19 wide and
6Uhigh Mounting flexibility Flush-, semi-flush, wall- and rack
mounting Side by side Compression type or ring lug cable
termination SA-T Training1MRG004718Slide 3terminationSection
03Relion 670 series Hardware general I/O flexibilityy 0 - 12 - 24
analog inputs with different input combinations 1A or 5A on the CT
inputs Up to 220V on the VT inputs 3 to 14 slot positions to be
used for binary inputs/outputs and transducer inputs Max 224 binary
inputs Max 96 binary outputs Max 24 mA inputs Binary input voltage
24-250 Vdc Binary input voltage 24 250 Vdc LDCM (per LDCM and in
each direction) 4 currents and 8 binary signals or or 192 binary
signals SA-T Training1MRG004718Slide 4Section 03Relion 670 series
Hardware general Time synchronization Time synchronization TCP/IP,
Ethernet IEC 61850, DNP 3.0 LON, SPA IRIG-B GPS Binary input
CommunicationIEC 61850 8 1 DNP 3 0 IEC 61850-8-1, DNP 3.0 LON, SPA
LDCM (C37.94, G.703 or X21) SA-T Training1MRG004718Slide 5Section
03Relion 670 series Hardware general Transformer Input Module
TRM11/1 19 case 6U high Transformer Input Module TRM1 and TRM2
(none, one or two) Analog Digital Conversion module ADM1 and ADM2
(corresponds to1/1 19case, 6U highADM1 and ADM2 (corresponds to
TRMx) Central Processing Unit NUM (always included) (always
included) Input / Output modules BIM, BOM, SOM, IOM and MIM Power
supply module PSM (always included)In- / O t tPower SupplyNUMADMTRM
SA-T Training1MRG004718Slide 6OutputsSection 03Hardware
configuration Backplane modules Universal Backplane Module1/1 19
rackUBM Universal Backplane Module (UBM) 1/1 19 case (from right to
left) TRM1 and TRM2, Slot 40, 411/1 19rackUBM, , ADM1 and ADM2,
Slot 31, 32 NUM, Slot P30 (always) 1/2 19 caseCBM TRM1, Slot P40
ADM1, Slot P31 NUM, Slot P30 (always)Combined Backplane
ModuleUBMSlot no: P1, P3 P13 P30 - P32P40, P41 Combined Backplane
Module (CBM) 1/1 19 case (from left to right) PSM Slot 1
(always)1/2 19 rackUBM PSM, Slot 1 (always) 11 CAN-bus slots, Slot
3-13 1/2 19 case PSM, Slot 1 (always)CBM SA-T
Training1MRG004718Slide 7 3 CAN-bus slots, Slot 3-5Slot no: P1, P3
P5 P30, P31 P40 Section 03Hardware configuration 1/1 19 case 3 cPCI
positionsADMTRMPSMNUMCAN-busPMCPC-MIP1212CAN-masterI/O d l lik BIM
BOM SOM11*CAN-busUBMCBMI/O modules like BIM, BOM, SOM, IOM and MIM
connected to the CAN-busPSMADMADMNUMTRMTRMCAN-busPMCPC-MIP1212P AAN
TT SA-T Training1MRG004718Slide 8View from the front sideSection
03Hardware configuration 1/1 19 case 2 cPCI positionsADM1RMPSMUMCAN
bPMCPC-MIP1212A1TRPNCAN-busCBMPC MIP 2 2CAN-masterI/O modules like
BIM, BOM, SOM IOM and MIM connected14*CAN-busUBMSOM, IOM and MIM
connected to the CAN-bus SA-T Training1MRG004718Slide 9View from
the front sideSection 03Transformer input module (TRM) Isolation
barrier preventing Isolation barrier preventing disturbances to
enter into 670 series Adapt measured values to static Adapt
measured values to static circuitry Up to 12 analog inputs can be
connected (settable 50 or 60 Hz) connected (settable 50 or 60 Hz) 0
- 6 U, 110-220V rated range 6 -12 I, 1A and/or 5A rated current
Connectors (same type for all I/O-modules) Screw compression or
Ring lug SA-T Training1MRG004718Slide 10Section 03Transformer input
module (TRM1 or 2)1 A 1 A 5 A 5 A 110-220 V 1 A 1 A metering5 A 5 A
metering110 220 V9I+3U9 3All except REB6709 3All except REB6705 4
3RET670 RED6707I+5U7 5All except REB6707 5All except REB670 All
except REB6701 6 5Customized4 3 5Customized4 3 5Customized4 3
5Customized4 3 5Customized6I+6U6 6All except REB6706 6All t REB6706
6All except REB6703 3 6REL670 SA-T Training1MRG004718Slide
11Section 03Transformer input module (TRM1 or 2)1 A 1 A 5 A 5 A
110-220 V 1 A 1 A metering5 A 5 A metering110 220 V12I12All except
REL670 and REC67012All except REL670 and REC6706I6All except
REB6706All t REB6706All except REB670 SA-T Training1MRG004718Slide
12Section 03Analog to digital conversion module (ADM1)Analog inputs
(from TRM1)P31 P31Mounting position for OEM module (only on
ADM1)P31:1cPCIbusP ibl ti iti f Possible mounting position forLDCM,
GTM or RS485 modulePossible mounting positionP31:2Possible mounting
position for LDCM or GTM moduleP31:3 SA-T Training1MRG004718Slide
13FrontSection 03Analog to digital conversion module (ADM2)Analog
inputs (from TRM2)P32cPCIbusPossible mounting position forLDCM or
GTM modulesP32:2P32:3 SA-T Training1MRG004718Slide 14FrontSection
03Numerical module (NUM) UBM interfaceP30UBM interfaceMounting
position P30:1g pfor SLM moduleP ibl ti iti P30 2 Possible mounting
position for IRIG-B or LDCM modulesP30:2Possible mounting position
forLDCM moduleP30:3cPCIbusF t SA-T Training1MRG004718Slide
15FrontSection 03Optical Ethernet module (OEM) Communication
Communication Ethernet (100 Mbit/s) IEC 61850-8-1 IEC 61850-9-2LE
DNP 3.0One or two channels One or two channels Connectors Glass
fiber type STP31:1 Glass fiber, type ST Max 1 module per IED
Mounted on ADM1 Mounted on ADM1 SA-T Training1MRG004718Slide
16Section 03Serial communication module (SLM) CommunicationRear
Communication LON SPA or IEC 60870-5-103 Connectors Glass fiber,
type ST Plastic fiber, type HFBR snap-inP30:1p Combination of glass
& plastic fiberM 1 d l IED Max 1 module per IED Mounted on NUM
SA-T Training1MRG004718Slide 17Section 03Line data communication
module (LDCM) Up to 4 modules per IED (option)Rearp p ( p )
Application example Line differential protection Need to exchange
large number of binary informationRearinformation Communication:
multiplexed, route switched or dedicated fibre using C37.94external
modems for G 703 and G 703E1 external modems for G.703 and G.703E1
Different ranges Short range (SR), Multi-mode, 3 km Medium range
(MR), Single-mode, 80 km Long range (LR), Single-mode, 120-150 km
Connectors SR: Type ST; MR and LR: Type FC SR: Type ST; MR and LR:
Type FC Module mounted on ADM and/or on NUM(depending if IRIG-B and
RS485 are included and the number of LDCMs) SA-T
Training1MRG004718Slide 18Section 03Galvanic LDCM (X21-LDCM) The
optical ports in LDCM (C37 94) may be replaced with galvanic The
optical ports in LDCM (C37.94) may be replaced with galvanic
X21-port (option) Up to 4 modules per IED (same as optical LDCM)
Connectors Electrical 15-pole female mini D-sub Module mounted on
ADM and/or on NUM (depending if IRIG-B and RS485 are included and
number of LDCMs) SA-T Training1MRG004718Slide 19Section 03GPS time
synchronization module (GTM) Time Synchronizing (option)Rear Time
Synchronizing (option) Number of channels GPS:1 Rear PPS:1
Connectors Antenna 50 Ohm: SMA Optical PPS: Type ST Module mounted
on ADM (1p2) SA-T Training1MRG004718Slide 20Section 03Time
synchronizing module (IRIG-B) Time Synchronizing usingR Time
Synchronizing using a station clock (option) Number of channels
Rear IRIG-B:1 PPS:1 Connectors Electrical IRIG-B: BNCP30:2 Optical
PPS: Type STModule mounted on NUM Module mounted on NUM SA-T
Training1MRG004718Slide 21Section 03Galvanic RS485 communication
module (DNP 3.0) Station BusRear Station Bus Communication (option)
DNP 3.0Rear Serial communication, alternative for Ethernet
communication 2400 19200 Bits/s Connectors RS 485 6-pole Soft
ground 2-pole connector Max 1 module per IED SA-T
Training1MRG004718Slide 22 Mounted on ADM1Section 03Power supply
module (PSM) DC/DC Converter providing full DC/DC Converter
providing full isolation between IED and external battery systemP1
Input range: 24-60 V DC or Input range: 90-250 V DC I t l f il l t
t Internal fail relay output Connectors (same type for all
I/O-modules)) Screw compression or Ring lugFront SA-T
Training1MRG004718Slide 23FrontSection 03Binary input module (BIM)
16 Independent Binary Inputs 16 Independent Binary Inputs Debounce
filter, T = 5 ms Oscillation suppression detection within 1 s;>
0 - 40 Hz Pulse counting at all inputs (option) Auxiliary voltage
Auxiliary voltage 24/40 V DC (20%) 48/60 V DC (20%) 110/125 V DC
(20%) 220/250 V DC (20%) Connectors (same type for all I/O- (
ypmodules) Screw compression or Ring lug SA-T
Training1MRG004718Slide 24g ugSection 03Binary output module (BOM)
24 Single Output Relays or 24 Single Output Relays or 12 Double
pole Command Output Relays Connectors (same type for all
I/O-modules)Screw compression or Screw compression or Ring lug SA-T
Training1MRG004718Slide 25Section 03Static binary output module
(SOM) 6 Fast Static Outputs 6 Fast Static Outputs 48-60 VDC or
110-250 VDC 110 250 VDC Operating time < 1ms 6 Change over
Output Relays g p y Connectors (same type for all I/O-modules)
Screw compression or Ring lug SA-T Training1MRG004718Slide
26Section 03Binary input/output module (IOM) 8 independent Binary
Inputs and 12 8 independent Binary Inputs and 12 Binary Output
Relays (10 trip and signal relays, 2 fast signal relays) Fix filter
time 5 ms Fix filter time 5 ms Auxiliary voltage 24/40 V DC (20%)
48/60 V DC (20%) 110/125 V DC (20%)220/250 V DC (20%) 220/250 V DC
(20%) Connectors (same type for all I/O-modules) Screw compression
or Ring lug SA-T Training1MRG004718Slide 27Section 03mA input
module (MIM) 6 independent input channels 6 independent input
channels Software selected input ranges 0-5, 0-10, 0-20, 4-20 mA, ,
, 5, 10, 20 mA Resolution: 16 bit Accuracy: 0,1% Connectors (same
type for all I/O-modules) Screw compression or Ring lug Ring lug
SA-T Training1MRG004718Slide 28Section 03Hardware overview, 1/1 19
case11*CAN 3*PCISLMOEMPSMLDCM(4 pieces)GTMNUMTRM1 TRM2IRIG-B SA-T
Training1MRG004718Slide 29ADM1 ADM2 I/ONUMRS485Section 03Hardware
overview I/O modules, 1/1 case MIM *)(max 4)IOM(max 6)1/1 CaseBOM
*)6 Transducer inputs,setting range+ 20 mASOM *)(max 4)1/1
CaseOption 1: 1 TRMBIM(max 11/14))(max 4)12 binary outputsand 8
binary inputs 14 I/O modulesOption 2: 2 TRM(max 11/14)6 static and
6 change over binary outputs 2 TRM 11I/O modules16 binary inputs24
binary outputs*) Total number of MIM, SOM and BOM must be 4 SA-T
Training1MRG004718Slide 30) ,Section 03Hardware overview I/O
modules, 3/4 case MIM *)(max 1)IOM(max 5/6)3/4 CaseBOM *)6
Transducer inputs,setting range+ 20 mASOM *)(max 4)3/4 CaseOption
1: 1 TRMBIM(max 5/8))(max 4)12 binary outputsand 8 binary inputs 8
I/O modulesOption 2: 2 TRM(max 5/8)6 static and 6 change over
binary outputs 2 TRM 5 I/O modules16 binary inputs24 binary
outputs*) Total number of MIM, SOM and BOM must be 4 SA-T
Training1MRG004718Slide 31Section 03Hardware overview I/O modules,
1/2 case MIM(n.a.)IOM(max 3)1/2 CaseBOM6 Transducer inputs,setting
range+ 20 mASOM(max 3)1/2 Case 1TRM 3 I/O modulesBIM(max 3)(max
3)12 binary outputsand 8 binary inputs(max 3)6 static and 6 change
over binary outputs16 binary inputs24 binary outputs SA-T
Training1MRG004718Slide 32Section 03Hardware overview I/O modules,
Ring lugs 1/1 Case 3/4 Case 1/1 CaseOption 1: 1 TRM3/4 CaseOption
1: 1 TRM1/2 Case 7 I/O modulesOption 2: 2 TRM 4 I/O modulesOption
2: 2 TRM 1TRM 1 I/O modules 2 TRM 5 I/O modules 2 TRM 2 I/O modules
SA-T Training1MRG004718Slide 33Section 03Local HMI Small or medium
size screen Small or medium size screen Graphical LCD display (80 x
240 or 320 x 240 pixels)3 status indication LEDs indicate the 3
status indication LEDs indicate the status of the IED Ready, Start
and Trip 15 indication LEDs 12 push buttons for navigation, control
etc. Ethernet front port connection, RJ45 SA-T
Training1MRG004718Slide 34Section 03Summary Basic hardware modules
Universal Backplane Module (UBM) p ( ) Combined Backplane Module
(CBM) Main Processing Module (NUM)Power Supply Module (PSM) Power
Supply Module (PSM) SA-T Training1MRG004718Slide 35Section
03Summary Specific hardware modules Binary Input Module (BIM) y p (
) Binary Output Modules Relay outputs (BOM) Static and relay
outputs (SOM) Binary I/O Module (IOM) mA input Module (MIM) Analog
Input Module (TRM) Analog to Digital conversion Module (ADM) Data
communication Module (LDCM) Optical (C37.94) or galvanic (X21)
Serial communication Modules LON, SPA or IEC 60870-5-103 (SLM) DNP
3.0 galvanic (RS485) Optical Ethernet Module (OEM) Time
Synchronization Modules GPS (GTM)IRIG B SA-T
Training1MRG004718Slide 36 IRIG-BSection 03Summary Communication
OEM (TCP/IP, Ethernet, SA-system) OEM (TCP/IP, Ethernet, SA system)
IEC 61850-8-1 IEC 61850-9-2LEDNP 3 0 DNP 3.0 SLM (Serial
Communication Module) LON (SA-system) SPA or IEC 60870-5-103
(SMS-system) RS485 (SA-system) DNP 3.0 LDCM (communication between
IEDs) IEEE/ANSI C37.94 IEEE/ANSI C37.94 G.703/G.703E1 optical to
galvanic conversion X21-modem connection SA-T
Training1MRG004718Slide 37ode co ec oSection 03Summary Time
synchronization OEM (TCP/IP, Ethernet) OEM (TCP/IP, Ethernet) IEC
61850-8-1 DNP 3.0 SLM (Serial Communication Module) LON SPA SPA
RS485 DNP 3.0 GSM (GPS module) IRIG-B Electrical IRIG-B Electrical
IRIG B Optical PPS Binary input SA-T Training1MRG004718Slide
38Section 03 SA-T Training1MRG004718Slide 39
