Upload
ealfora
View
21
Download
0
Tags:
Embed Size (px)
DESCRIPTION
RN4.0_Upgrade_for_RNC450
Citation preview
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
1
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
4
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
5
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
6
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
7
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
8
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
9
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
10
eager
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
11
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
12
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
13
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
14
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
15
The SF10E operation is controlled by PPC7 HW block. The block utilises PowerQUICCII communication processor MPC8280 version HiP7. This unit is backward compatible with SF10.
The unit has 10 Gbit/s nonblocking ATM cell switching capacity and provides the following interfaces:
8 hi-speed ports with 1.65 Gbit/s of usable bandwidth each. It is connected to all MX1G6 units and other hi-speed units via optical interface in the front panel. To implement port redundancy, it will require two of these ports.
Redundant HMS interface connected to HMS Slave node type B. It supports maximum speed of 1 Mbit/s.
1 x 10/100Base-T for hardware debugging purpose
UTOPIA level 2 redundant multiplexer port interfaces for ATM based DMX messaging
RS232 serial interface with RJ45 connector for HW debugging and service terminal interface.
Activity signals, _ACT_2N and _ACT_EXT, to interchange activity information between redundant units.
Synchronisation signal, FSYNC_2N and FSYNC_EXT, with 8 kbit/s of speed.
19.44 MHz system clock.
Unit power -48 V and HMS power +5V
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
16
The NP2GE-B operation is controlled by PQ3CC HW block. The block utilises PowerQUICCIII communication processor MPC8568.
The unit has 2 x Gigabyte Ethernet interfaces for external connection. At the same time, it supports approximately 2.5 Gbit/s multiprotocols traffic.
This unit provides the following interfaces:
2 x 1000Base-T Ethernet with RJ45 connector.
2 x 1000Base-Lx Ethernet with LC connector. The connector is integrated to transceiver in Small Form Plugable (SFP) format. This transceiver unit transmits Class 1 laser. It can accommodate SMF or MMF (in short operation distance)
RS232 serial interfaces with RJ45 connector for HW debugging and service terminal interface.
Redundant hi-speed Switch Fabric port connected to SF20H unit (require BISFC)
19.44 MHz synchronisation and timing signals
Redundant HMS interface connected to HMS Slave node type B. It supports maximum speed of 1 Mbit/s.
Unit power -48V and HMS power +5V
2 x 10/100Base-T for Ethernet based control messaging (future implementation)
Duplicated 10/100Base-T for DCN connection toward SWU (ESA24 card)
Redundant signals, L1_alarm and L2_alarm, for Ethernet link logic alarm
Redundant signals, PIU_OK and PAIR_OK, for interworking of redundant NP2GE-B pair.
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
17
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
18
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
19
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
20
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
21
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
22
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
23
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
24
GTPU and A2SU are exist as long as NIS1(P) is used as network interface
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
25
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
26
CDSP-DH contains 4 DMPGs. The operation of each DMPG is controlled by PPC7 HW block which utilises PowerQUICCII communication processor MPC8280 version HiP7.
The DMPG has 2 Himalaya DSPs, which has 1200 MHz core speed and 256 MB external DDR2 memory each.
CDSP-DH provides the following external interfaces:
Four 10/100 Base-T Ethernet connected to each DMPG. They are used during R&D phase to debugging.
Four RS232 serial interfaces with RJ45 connector for HW debugging and service terminal interface, connected to each DMPG.
Multiplexer port interface connected to working and spare multiplexer units.
Two 19.44MHz timing and synchronisation signals, REF Clock A and REF Clock B, consecutively for active and redundant source.
Redundant HMS interface connected to HMS Slave node type B. It supports maximum speed of 1 Mbit/s.
Unit power -48 V and HMS power +5V
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
27
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
28
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
29
DSP pool reservation on CDSP-C is example only. The actual share depends on HW configuration.
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
30
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
31
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
32
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
33
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
34
All connection to/from BISFx unit require intermediate cable with SFP connectors, CSB.
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
35
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
36
The SF20H operation is controlled by PPC7 HW block. The block utilises PowerQUICCkII communication processor MPC8280 version HiP7.
The unit has 20 Gbit/s non-blocking ATM cell switching capacity and provides the following interfaces:
32 hi-speed ports with 1.65 Gbit/s of usable bandwidth each. It is connected to all MX1G6 units and other hi-speed units via optical cables (requires BISFA and BISFD). Port redundancy is implemented using two of these ports.
Redundant HMS interface connected to HMS Slave node type B. It supports maximum speed of 1 Mbit/s.
2 x 10/100Base-T for Ethernet based control messaging (future implementation)
Redundant multiplexer port interfaces for ATM based DMX messaging
RS232 serial interface with RJ45 connector for HW debugging and service terminal interface.
Activity signals, _ACT_2N and _ACT_EXT, to exchange activity information between redundant units.
Synchronisation signal, FSYNC_2N and FSYNC_EXT, with 8 kbit/s of speed.
19.44 MHz system clock.
Unit power -48 V and HMS power +5V
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
37
The MX1G6-A operation is controlled by PQ3CC HW block. The block utilises PowerQUICCIII communication processor MPC8560.
The unit has 1.65 Gbit/s ATM cell multiplexing/demultiplexing capacity to/from SF20H unit. It also provides the following interfaces:
20 multiplexer ports with 160 Mbit/s of speed each. It connects all tributary units to/from SF20H via optical cables (requires BISFB).
Redundant HMS interface connected to HMS Slave node type B. It supports maximum speed of 1 Mbit/s.
2 x 10/100Base-T for Ethernet based control messaging (future implementation). One of these interface also connected to front panel for R&D purpose.
Redundant hi-speed Switch Fabric port connected to working and spare SFU.
RS232 serial interface with RJ45 connector for HW debugging and service terminal interface.
Redundancy signals, SWITCHOVER_A and SWITCHOVER_B, to exchange information between redundant MXU.
19.44 MHz system clock.
Unit power -48 V and HMS power +5V
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
38
The NP8S1-B operation is controlled by PQ3CC HW block. The block utilises PowerQUICCIII communication processor MPC8567.
The unit has 8 x STM-1/OC-3 interfaces for external connection. At the same time, it supports approximately 1.2 Gbit/s AAL2 connectivity (8*155.52 Mbit/s) for any AAL2 based traffic.
This unit provides the following interfaces:
8 x optical interfaces with LC connector. The connector is integrated to transceiver in Small Form Pluggable (SFP) format. This transceiver unit transmits Class 1 laser.
RS232 serial interfaces with RJ45 connector for HW debugging and service terminal interface.
Redundancy signals, SWITCHOVER_A and SWITCHOVER_B, to exchange information between redundant NPS1.
Redundant hi-speed Switch Fabric port connected to SF20H unit (require BISFC)
2 x 10/100Base-T for Ethernet based control messaging (future implementation)
Duplicated 10/100Base-T for DCN connection toward SWU (ESA24 card)
Redundant HMS interface connected to HMS Slave node type B. It supports maximum speed of 1 Mbit/s.
Unit power -48V and HMS power +5V
19.44MHz reference clock output. The reference clock is extracted from interface to be forwarded to TSS3 plugin unit.
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
39
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
40
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
41
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
42
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
43
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
44
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
45
RN77262EN10WSA0
RN4.0 Upgrade for RNC450
46