02-15002770-New Royal-EN-03.indd - Seattle Coffee Gear

Type HD8930

OPERATING INSTRUCTIONS

READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THE MACHINE.

Engli

sh

02

EN0

2

Register your product and get support at

www.philips.com/welcome

IMPORTANT SAFEGUARDSWhen using electrical appliances, basic safety precautions should always be followed, including the following:1. Read all instructions.2. Do not touch hot surfaces. Use handles or knobs.3. To protect against fire, electric shock and injury to persons do not immerse

cord, plugs, or appliance in water or other liquid.4. Close supervision is necessary when the appliance is used by or near

children.5. Unplug from outlet when not in use and before cleaning. Allow to cool

before putting on or taking off parts, and before cleaning the appliance.6. Do not operate any appliance with a damaged cord or plug or after the

appliance malfunctions, or has been damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or adjustment.

7. The use of accessory attachments not recommended by the appliance manufacturer may result in fire, electric shock or injury to persons.

8. Do not use outdoors.9. Do not let cord hang over edge of table or counter, or touch hot surfaces.10. Do not place on or near a hot gas or electric burner, or in a heated oven.11. Always attach plug to appliance first, then plug cord into wall outlet. To

disconnect, turn any control to “off”, then remove plug from wall outlet.12. Do not use appliance for other than intended use.13. Save these instructions.

SAVE THESE INSTRUCTIONS

CAUTIONThis appliance is for household use only. Any servicing, other than cleaning and user maintenance, should be performed by an authorized service center. Do not immerse machine in water. To reduce the risk of fire or electric shock, do not disassemble the machine. There are no parts inside the machine serviceable by the user. Repair should be done by authorized service personnel only.1. Check voltage to be sure that the voltage indicated on the nameplate

corresponds with your voltage.2. Never use warm or hot water to fill the water tank. Use cold water only. 3. Keep your hands and the cord away from hot parts of the appliance during

operation.4. Never clean with scrubbing powders or harsh cleaners. Simply use a soft

cloth dampened with water.5. For optimal taste of your coffee, use purified or bottled water. Periodic

descaling is still recommended every 2-3 months.6. Do not use caramelized or flavored coffee beans.

INSTRUCTIONS FOR THE POWER SUPPLY CORD

A. A short power-supply cord (or detachable power-supply cord) is to be provided to reduce risks resulting from becoming entangled in or tripping over a longer cord.

B. Longer detachable power-supply cords or extension cords are available and may used if care is exercised in their use.

C. If a long detachable power-supply cord or extension cord is used,1. The marked electrical rating of the detachable power-supply cord or

extension cord should be at least as great as the electrical rating of the appliance

2. If the appliance is of the grounded type, the extension cord should be a grounding-type 3-wire cord, and

3. The longer cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over.

Contents

Introduction ..........................................................................3

General Description (fi g. 1) ..................................................3

Important ..............................................................................4Intended Use .................................................................................................................................................. 4Power Supply - Power Cord ...................................................................................................................... 4For the Safety of Others ............................................................................................................................. 4Danger of Burns ............................................................................................................................................ 4Machine Location - Suitable Location for Operation and Maintenance .................................. 4Storing the Machine - Cleaning .............................................................................................................. 5Malfunction .................................................................................................................................................... 5Fire Safety Precautions ............................................................................................................................... 5

First Use .................................................................................6Packaging ....................................................................................................................................................... 6Preliminary Operations .............................................................................................................................. 6Double Function Buttons .......................................................................................................................... 8Setting the Language (Upon First Use) ................................................................................................ 9Warm-up and Rinsing ................................................................................................................................. 9Rinse/Self-Cleaning Cycle ........................................................................................................................10For a Perfect Espresso: Rinse the Coff ee Circuit if Using the Machinefor the First Time or After a Long Period of Inactivity. ...................................................................10

Measuring and Adjusting Water Hardness ...................... 12

"INTENZA+" Water Filter ................................................... 14

Adjustments ....................................................................... 16Adjusting the Coff ee Grinder .................................................................................................................16Adjusting the "Aroma" - Amount of Ground Coff ee ......................................................................16Adjusting the Coff ee Length ..................................................................................................................17Adjusting the Cappuccino or Latte Macchiato Length .................................................................18Eco-friendly: Stand-by ..............................................................................................................................19

Brewing Coff ee ................................................................... 19Cup-warming Surface ...............................................................................................................................19Adjusting the Dispensing Spout ...........................................................................................................19Using Coff ee Beans ....................................................................................................................................21Using Pre-ground Coff ee .........................................................................................................................21

Brewing Cappuccino ......................................................... 23

Latte Macchiato ................................................................. 24

Milk Handling .................................................................... 25Milk Thermos ................................................................................................................................................25Milk Container .............................................................................................................................................27

"SPECIAL" Products ............................................................ 28Dispensing Hot Water ...............................................................................................................................28Long Coff ee ..................................................................................................................................................29Hot Milk ..........................................................................................................................................................29American Coff ee .........................................................................................................................................30

Beverage Programming .................................................... 31Beverage Parameters ................................................................................................................................31Dispensed Beverages Counters ............................................................................................................31Hot Water Parameters ...............................................................................................................................32Default Parameters ....................................................................................................................................32

Machine Programming ..................................................... 33Machine Menu.............................................................................................................................................34Display Menu ...............................................................................................................................................35Water Menu ..................................................................................................................................................35Maintenance ................................................................................................................................................36Factory Settings ..........................................................................................................................................36

Cleaning and Maintenance ............................................... 37General Cleaning ........................................................................................................................................37Cleaning the Cappuccinatore (After Each Use) ...............................................................................38Day Cleaning - Thermos ...........................................................................................................................40Monthly Cleaning - Cappuccinatore + Thermos (Thorough Cleaning) ..................................42

Brew Group ........................................................................ 45Weekly Cleaning - Brew Group ..............................................................................................................45Brew Group Cleaning with "Coff ee Clean Tablets": ........................................................................47Brew Group Lubrication ...........................................................................................................................48

Descaling ............................................................................ 50

LCD Display Warnings ....................................................... 54

Troubleshooting ................................................................ 56

Technical Specifi cations .................................................... 57

Service ................................................................................ 58

2

1

MENU OK ESC

21

16

17

23

26 24

22

1 2 3

13

11

14

15

4 5

7

8

9 1012

18

19

29

2028

6

27 32

31

25 30

33 3834 3935 4036 4137

ENGLISH 3

Introduction

Congratulations on your purchase and welcome to Philips! To fully benefi t from the support that Philips off ers, register your product at www.philips.com/welcome.

In this user manual you will fi nd all the information you need to install, use, clean and descale your appliance. In case you need further support, please contact the toll free Philips consumer care help line. You can fi nd the phone number on the last page of this document and in the warranty booklet supplied with the appliance.

General Description (fi g. 1)

1 Cup-warming surface2 Water tank3 Water tank lid4 Coff ee dose adjustment5 Grinder adjustment6 Cappuccinatore cover7 Hot water wand8 Dispensing spout9 Brew group10 Service door11 Pre-ground coff ee compartment + lid12 Coff ee bean hopper lid13 Coff ee bean hopper14 Cappuccinatore (removable type)15 Coff ee grounds drawer16 Cup holder grill17 Full drip tray indicator18 Drip tray19 Power button20 Power cord socket21 Pre-ground coff ee dosing unit22 Grease for brew group23 Power cord24 Cleaning brush25 Milk circuit detergent26 Water hardness test27 Milk Thermos28 Descaling solution29 (INTENZA+) Filter30 Brew group cleaning tablets “Coff ee Clean Tablets”

31 Suction tube for Cappuccinatore32 Connection hose Thermos - Cappuccinatore33 Pre-ground coff ee selection button 2nd Function - "Menu" button to access the programming mode 34 Espresso coff ee brew button35 Coff ee brew button 2nd Function - "OK" button to confi rm selection36 Special beverages selection button 2nd Function - “ESC” button to exit or stop the brewing procedure.37 Display38 Cappuccinatore "Clean" button 2nd Function - "Page Up" button to scroll the menu39 Cappuccino brew button 2nd Function - "Page Down" button to scroll the menu40 Latte Macchiato brew button41 ON/OFF button

4 ENGLISH

Important

Read this user manual carefully before using the appliance and save it for future reference.

Never allow water to come into contact with any of the electrical parts of the machine: Danger of short circuit! Hot water may cause scalding! Never not direct the hot water jet towards body parts. Handle the hot water wand with care.

Intended Use

The coff ee machine is intended for domestic use only. Do not make any technical changes or use the machine for unauthorised purposes since this would create serious hazards! The appliance is not to be used by persons (including children) with reduced physical, mental or sensory abilities or with scarce experience and/or expertise, unless they are supervised by a person responsible for their safety, or they are instructed by this person on how to properly use the machine.

Power Supply - Power Cord

Connect the coff ee machine only to a suitable socket.The socket to which the machine is connected must be:- Compatible with the type of plug installed on the machine;- Suitably sized to comply with the data on the plate attached to the

appliance;- Connected to an effi cient earthing system.

Never use the coff ee machine if the power cord is defective or damaged. If the power cord is damaged, it must be replaced by the manufacturer or by its authorised service centre. Do not pass the power cord around corners, over sharp edges or over hot objects and keep it away from oil. Do not use the power cord to carry or pull the coff ee machine. Do not pull out the plug by the power cord or touch it with wet hands. Do not let the power cord hang freely from tables or shelves.

For the Safety of Others

Prevent children from playing with the machine. Children are not aware of the risks related to electrical household appliances. Do not leave the machine packaging materials within the reach of children.

Danger of Burns

Never direct the jet of hot steam and/or hot water towards yourself or oth-ers: Danger of scalding! Always use the handles or knobs provided.

Machine Location - Suitable Location for Operation and Mainte-nance

For best use, it is recommended to:• Choose a safe, level surface, where there will be no danger of overturn-

ing the appliance or being injured;• Choose a location that is suffi ciently well-lit, clean and near an easily

ENGLISH 5

reachable socket;• Provide for a minimum distance from the sides of the machine as

shown in the illustration;

• While switching on or off the machine, we suggest placing an empty glass under the dispensing spout.

Do not keep the machine at temperatures below 0°C. Frost may damage the machine. Do not use the coff ee machine outdoors. In order to prevent its housing from melting or being damaged, do not place the machine on very hot surfaces and close to open fl ames.

Storing the Machine - Cleaning

Before cleaning the machine, turn it off by pressing the " " button and then by switching the power button to "0". Finally, remove the plug from the socket. Keep the machine at its best, clean and store it properly.Since the machine uses natural ingredients to brew beverages (coff ee beans, water, milk, etc.), some residues of ground coff ee or condensed wa-ter could be present on its supporting surface. For this reason we recom-mend to periodically clean both the visible parts of the machine and the area beneath it.

Before storing the machine we strongly recommend to clean it:- Water left in the tank and/or the water circuit for several days should

not be consumed. If the machine is going to remain inactive for a long time, dispense water from the hot water wand and carefully clean the Cappuccinatore (if supplied).

- Turn off the power button and clean the machine. Finally, remove the plug from the socket. Wait for the machine to cool down.

Never immerse the machine in water! Store it in a dry place, out of the reach of children. Keep it protected from dust and dirt.It is strictly forbidden to tamper with the internal parts of the machine.

Malfunction

In case of failure, problems or a suspected fault resulting from the falling of the machine, immediately remove the plug from the socket. Never attempt to operate a faulty machine. For further information on troubleshooting and service, please refer to the "Troubleshooting" and "Service" chapters.

Fire Safety Precautions

In case of fi re, use carbon dioxide (CO2) extinguishers. Do not use water or dry powder extinguishers.

6 ENGLISH

First Use

Packaging

The original packaging has been designed and constructed to protect the machine during transport. We recommend keeping the packaging material for possible future transport.

Preliminary Operations

Remove the drip tray with grill and the coff ee machine from the packaging. Place the machine in a place that meets the requirements described in the safety regulations.

1 Place the drip tray with grill into its seat on the machine. Make sure the tray is fully inserted to its limit stop.

Note: Insert the plug into the socket only when indicated and make sure the power button is on "0".

Important Note: Carefully read the explanations of all the warnings the machine displays to the user on the control panel LCD display (section "LCD Display Warnings").

NEVER remove the drip tray when the machine is on. Wait for a couple of minutes after turning on/off , as the machine will be carrying out a rinse/self-cleaning cycle (see section "Rinse/Self-Cleaning Cycle").

1

2

4 Rinse and fi ll it with fresh water, making sure that the (MAX) level indicated in the tank is not exceeded. Place the water tank back into its seat and reposition the lid.

Fill the tank only with fresh, non-sparkling water. Hot water or any other liquid may damage the tank and/or the machine. Do not operate the ma-chine without water. Make sure there is enough water in the tank.

2 Remove the lid from the water tank.

3 Remove the water tank from its seat by only using the relevant handle.

ENGLISH 7

5 Make sure the dispensing spout is in correct position. Move it horizon-tally until you hear the CLICK indicating the correct position.

If this is not done, some product might leak out of the dispensing spout.

1

2

11 Switch the power button to "I" to turn on the machine.

Note: The power button is located in the rear part of the machine. After carrying out a check cycle, the machine goes into stand-by mode

and the " " button blinks.

12 To turn on the machine simply press the " " button.

Note: The language needs to be selected only upon fi rst use.

Note: Once the warm-up is complete, upon fi rst use the machine primes the circuit and performs a rinse cycle of the internal circuits. A small amount of water is dispensed. Wait for this cycle to be completed.

CLICK!

6 Remove the coff ee bean hopper lid.

Note: The hopper may be provided with diff erent safety features according to the regulations applicable in the country of use of the machine.

7 Slowly pour the coff ee beans into the hopper.

Only coff ee beans must be put into the coff ee bean hopper. Ground coff ee, instant coff ee or any other object may damage the machine.

8 Reposition the coff ee bean hopper lid.

9 Insert the plug into the socket on the back of the machine.

10 Insert the plug of the other end of the cable into a wall socket with suitable power voltage.

8 ENGLISH

Double Function Buttons

Some buttons in the control panel have a double function.The double function is only activated in certain moments during the ma-chine operation or when accessing the programming mode.

The additional function is indicated by the icon under the machine button.

MENU OK

OK ESC

MENU OK

Pre-ground coff ee selection - MENU Button

This button allows you to select the coff ee brew mode with pre-ground coff ee.

2nd Function - Hold it pressed for 5 seconds to access the machine pro-gramming menu.

Coff ee Brew - OK Button

This button allows you to select one coff ee brewing.

2nd Function - Press it to select the displayed option.

Special Beverages Selection - ESC Button

This button allows you to access the list of special beverages that the machine can brew.

2nd Function - Press it to exit the selected page and/or the programming mode completely and/or to stop brewing the beverage.

CLEAN - Page UP Button

This button allows you to perform a cleaning cycle of the Cappuccinatore by dispensing steam (see the special section for further details).

2nd Function - Press it to scroll the current page selection up.

Cappuccino Brew Button - Page DOWN Button

This button allows you to select the cappuccino brewing.

2nd Function - Press it to scroll the current page selection down.

ENGLISH 9

Setting the Language (Upon First Use)

At fi rst start up, the machine requires you to select and store the desired language for the displayed messages. This allows you to adjust the pa-rameters of the beverages to the typical parameters of the country where the machine is used. This is why some languages are diff erentiated also by country. If no language is selected, you will be requested to select it at next ma-chine start-up.

1 Select the language by pressing the " " or " " button.

2 Press the " " button to store the language.

Warm-up and Rinsing

1 Upon start-up, the machine activates the warm-up phase. Wait until it is completed.

Note: The bar is in progress to show that the machine is heating up the system.

2 Once the warm-up is complete, the machine performs a rinse cycle of the internal circuits.

Note: The bar is in progress to show that the machine is performing the system rinse cycle.

A small quantity of water is dispensed. Wait for the cycle to end.

Note: The cycle can be stopped by pressing the " " button.

3 Then, the machine is ready for use.

The logo is displayed indicating that the machine is ready for use.

Note: If the machine is being used for the fi rst time or after a long period of inactivity, follow the procedures described in the following section.

LANGUAGEITALIANOENGLISHDEUTSCHFRANÇAIS

HEATING UP…

RINSING

ESC STOP

10 ENGLISH

Rinse/Self-Cleaning Cycle

This cycle allows you to rinse the internal coff ee circuits with fresh water.The cycle is carried out:• At machine start-up (with cold boiler)

• After priming the circuit (with cold boiler)

• During the stand-by preparation phase (if at least a coff ee product has been brewed)

• During the turning off phase after pressing the " " button (if at least a coff ee product has been brewed).

A small amount of water will be dispensed to rinse and heat all the ma-chine parts; in this phase this icon is displayed.

Wait for the cycle to fi nish automatically. You can stop dispensing by press-ing the " " button.

MENU OK

For a Perfect Espresso: Rinse the Coff ee Circuit if Using the Machine for the First Time or After a Long Period of Inactivity.

These simple operations will make it possible to always brew excellent cof-fee. They have to be performed:A) At fi rst start-up;B) When the machine remains inactive for a long time (more than 2

weeks).

1 Place a large container under the dispensing spout.

2 Empty the water tank, wash and rinse it and fi ll it with fresh water.

3 Select the pre-ground coff ee brewing function by pressing the " " button once.

The display indicates that the pre-ground function has been selected.

RINSING

ESC STOP

ENGLISH 11

MENU OK

OK ESC

4 Press the " " button to select coff ee.

Note: Do not add pre-ground coff ee into the compartment.

8 Press the " " and the " " buttons, select and start dispensing HOT WATER.

9 When the hot water dispensing procedure is complete, empty the container.

10 The machine is now ready for use.

5 Press the " "button to start the dispensing procedure.

The machine will dispense hot water through the dispensing spout. Wait until the dispensing procedure is complete and empty the water tank.

6 Repeat the operations from step 1 to step 5 for 3 times, then continue with step 7.

7 Place a container under the hot water wand.

SPECIAL BEVERAGESHOT WATER

LONG COFFEEHOT MILK

AMERICAN COFFEE

HOT WATER

ESC STOP HOT WATER

MEMO

ESC ESC

INSERT GROUND COFFEE

AND PRESS OK

12 ENGLISH

Measuring and Adjusting Water Hardness

Measuring water hardness is very important in order to correctly manage the "INTENZA+" fi lter and the frequency with which the machine must be descaled.

1 Immerse the water hardness test strip - provided with the machine - in water for 1 second.

Note: The test strip is only valid for one measurement.

2 Check how many squares change colour and refer to the table.

Note: The letters correspond to the references that are located in the base of the Intenza fi lter. The fi lter must be adjusted according to this measurement.

3 The numbers correspond to the settings indicated in the following machine adjustments.

More precisely: 1 = (very soft water) 2 = (soft water) 3 = (hard water) 4 = (very hard water)

23

4

AB

CIn

tenz

a A

rom

a Sy

stem

Mac

hine

wat

er h

ardn

ess

sett

ing

1

4 Hold the " " button pressed for 5 seconds to access the program-ming mode.

5 To select the "MACHINE MENU" option, press the " " button.

Press the " " button for access.

6 Press the " " button until the "WATER MENU" option can be selected.


MACHINE MENUGENERAL MENUDISPLAY MENUWATER MENUMAINTENANCE


MENUBEVERAGE MENUMACHINE MENU

ENGLISH 13

7 Press the " " button to enter the "HARDNESS" menu.

Note: The machine is supplied with a standard adjustment suitable for most of the uses.

8 Press:

The " " button to increase the value

or

the " " button to reduce the value.

9 Press the " " button to confi rm the selected change.

10 Press the " " button until the following product brewing page is displayed.

HARDNESS1234

WATER MENUHARDNESS

ENABLE FILTERACTIVATE FILTER

14 ENGLISH

"INTENZA+" Water Filter

The “INTENZA+” water fi lter can improve the quality of water. Using the “INTENZA+” fi lter will prevent limescale from building up and will ensure a much more intense aroma to your espresso coff ee. We therefore recom-mend you to install the “INTENZA+” water fi lter. You can purchase it at your local dealer, on-line at the Philips on-line shop at http://shop.philips.com or at the authorised service centres.

2 Remove the "INTENZA+" water fi lter from its package. The fi lter should be set according to the measurements performed to set water hard-ness. Use the water hardness test strip provided with the machine. Set the "Intenza Aroma System" as specifi ed on the fi lter package (see section "Measuring and Adjusting Water Hardness").

A = Soft water B = Hard water (standard) C = Very hard water

ù

3 Immerse the "INTENZA+" water fi lter vertically (with the opening posi-tioned upwards) in cold water and delicately press its sides so as to let the air bubbles out.

1 Remove the small white fi lter from the tank and store it in a dry place sheltered from dust.

Measuring water hardness is very important in order to correctly manage the "INTENZA+" water fi lter and the frequency with which the machine must be descaled.

4 Put the fi lter into the empty tank. Press it until its limit stop.

5 Fill the tank with fresh drinking water and reinsert it into the machine.

ENGLISH 15


7 Hold the " " button pressed for 5 seconds to access the program-ming mode.

8 To select the "MACHINE MENU" option, press the " " button.


9 Press the " " button until the "WATER MENU" option can be selected.


10 Press the " " button until the "ACTIVATE FILTER" option can be se-lected.


11 Press the " " button.

Note: To exit the procedure, press the " " button.

12 Press the " " button to confi rm the introduction of the new fi lter.

13 Press the " " button to confi rm.

Wait until the machine stops dispensing the necessary water to activate the fi lter.

At the end of the cycle, remove the container that you had previously placed under the hot water wand.

Note: At the end of the procedure, the display automatically returns to the product brewing page. If the water fi lter is not available, insert the small white fi lter previously removed (see step 1) into the tank.


WATER MENUHARDNESS

ENABLE FILTERACTIVATE FILTER

ACTIVATE FILTER?

ACTIVATE FILTER

INSERT FILTER.FILL THE TANK

ACTIVATE FILTER

PLACE A CONTAINERUNDER THE

WATER SPOUT

ACTIVATE FILTER

ACTIVATE FILTER



16 ENGLISH

Adjustments

The machine that you have bought allows for certain adjustments that will permit you to use it to its full potential.

Adjusting the Coff ee Grinder

Warning! The grind adjustment lever must only be turned when the coff ee grinder is working. Do not pour ground and/or instant coff ee into the cof-fee bean hopper.

Do not insert any material other than coff ee beans into the hopper. The grinder contains moving parts that may be dangerous. Therefore, do not insert fi ngers and/or other objects. Turn off the machine by pressing the ON/OFF button and remove the plug from the socket before carrying out any type of operation inside the coff ee bean hopper.

The machine allows you to make slight adjustments to the coff ee grinder to adapt it to the kind of coff ee used.

To make any adjustment, use the lever located on the side of the machine.Turn the lever one notch at a time and brew 2-3 cups of coff ee; this is the only way to notice diff erences in grind.The reference marks indicate the grind setting. You can set diff erent de-grees of grind with the following references:

1 - Fine Grind2 - Coarse Grind

Adjusting the "Aroma" - Amount of Ground Coff ee

The machine allows you to program the amount of coff ee to be ground for preparing each cup of coff ee.

Warning! The Aroma adjustment lever must only be turned when the coff ee grinder is stopped. Adjustment must be performed before brewing coff ee.

To make any adjustment, use the lever located on the side of the machine.

The reference marks indicate the amount of ground coff ee which has been set. You can set diff erent amounts with the following references:

3 - Minimum coff ee amount (about 7 grams)4 - Maximum coff ee amount (about 11 grams)

1

3

2

4

ENGLISH 17

Adjusting the Coff ee Length

The machine allows you to adjust the amount of brewed coff ee according to your taste and/or the size of your cups.

Note: This function cannot be used to adjust American coff ee length, this prod-uct requires using the specifi c menu in the "BEVERAGE MENU".

Each time the “ ” or “ ” button is pressed and released, the machine brews a pre-set amount of coff ee. This amount may be reprogrammed according to your taste. Each button may be individually programmed for a specifi c brew setting.

Note: As an example, the following procedure describes the programming of the " " button, which is usually associated with espresso coff ee.

1 Place a cup under the dispensing spout.

2 Press and hold the " " button until the "MEMO" message is dis-played and remove your fi nger. The machine is now programming.

The machine begins the brewing phase. The "STOP COFFEE" message is displayed.

3 From now on, press the " " button when the desired amount of cof-fee is reached in the cup.

Now the " " button has been programmed; each time it is pressed and released, the machine will brew the same amount that has just been set.

MEMO

MEMO

ESC STOP COFFEE

18 ENGLISH

Adjusting the Cappuccino or Latte Macchiato Length

The machine allows you to adjust the brewed amount of Cappuccino (or Latte Macchiato) according to your taste and/or the size of your cups.

Each time the “ ” or “ ” button is pressed and released, the machine brews a pre-set amount of Cappuccino (or Latte macchiato). This amount may be reprogrammed according to your taste. Each button may be indi-vidually programmed for a specifi c brew setting.

Note: Before programming, you need to prepare the machine and milk as described in the Cappuccino section.

Note: As an example, the following procedure describes the programming of the “ ” button, which is normally associated with cappuccino.

1 Place a cup or a mug under the dispensing spout.

2 Press and hold the " " button until the "MEMO" message is dis-played and remove your fi nger. The machine is now programming.

The machine begins the milk dispensing phase. The “STOP MILK” mes-sage is displayed.

3 From now on, press the “ ” button when the desired amount of milk is reached in the cup.

4 Immediately after, the machine begins the coff ee brewing phase. The “STOP COFFEE” message is displayed.

5 From now on, press the “ ” button when the desired amount of cof-fee is reached in the cup.

Now the " " button has been programmed; each time it is pressed and released, the machine will brew the same amount that has just been set.

MEMO

MEMO

ESC STOP MILK

MEMO

ESC STOP COFFEE

ENGLISH 19

Eco-friendly: Stand-by

The machine is designed for energy saving. The machine automatically turns off after 30 minutes of inactivity.

Note: - During the turning off phase, the machine performs a rinse cycle, if a cof-

fee product has been brewed.- Time can be programmed according to your needs (see page 34).

To turn on the machine again, simply press the " " button (if the power button is set to "I"). In this case the machine will perform the rinse cycle only if the boiler is cold.

Adjusting the Dispensing Spout

Most cups on the market can be used with this coff ee machine.The height of the dispensing spout may be adjusted to better fi t the dimensions of the cups that you wish to use.

Manually move the dispensing spout up or down to adjust its height.

Brewing Coff ee

Before brewing coff ee check the lights on the display and make sure the water tank and coff ee bean hopper are full.

Before brewing coff ee, adjust the height of the dispensing spout according to your needs and select the aroma or pre-ground coff ee.

Cup-warming Surface

The machine features a cup-warming surface to keep your cups warm and ready. Warm cups bring out the full aroma of coff ee and let you enjoy its taste in full.

Place the cups that you usually use and wait until they are warm.

Note: the cup-warming surface has a higher temperature than the other machine surfaces, so we recommend not to touch it with sensitive body parts to avoid irritations.

Using the cup-warming surface for other purposes is prohibited.

The cup-warming surface is disabled by default for energy saving pur-poses. Refer to page 34 of the manual to activate is.

20 ENGLISH

The recommended positions are:For the use of small cups;

For the use of large cups.

Two cups can be placed under the dispensing spout to brew two cups of coff ee at the same time.

If you want to use tall glasses or mugs, push the dispensing spout to its limit stop. In this case, you can just brew one product at a time.

Note: Before any brewing procedure and/or when bringing the dispensing spout back to its normal brewing position, make sure that it is correctly posi-tioned. This can be noted through the CLICK indicating the correct position.If this is not done, some product might leak out of the dispensing spout.CLICK!

ENGLISH 21

Using Coff ee Beans

To brew coff ee, press and release: 1 The " " button for a cup of espresso;

or

the " " button for a cup of long espresso.

The brewing cycle then starts: To brew 1 cup of coff ee, press the desired button once. To brew 2 cups of coff ee, press the desired button twice consecutively.

Note: To brew 2 cups of coff ee, the machine automatically grinds and doses the correct amount of coff ee. Brewing two coff ees requires two grinding cycles and two brewing cycles, which the machine carries out automatically.

2 Once the prebrewing cycle is complete, coff ee begins to come out of the dispensing spout.

3 Coff ee brewing stops automatically when the set level is reached. However, it is possible to stop the coff ee brewing by pressing the “ ” button.

Note: The machine is adjusted to brew a true Italian espresso coff ee. This feature may slightly lengthen the brewing time, allowing the intense coff ee fl avour to develop fully.

Using Pre-ground Coff ee

This function allows using pre-ground coff ee.

Pre-ground coff ee must be poured into the relevant compartment posi-tioned next to the coff ee bean hopper. Only use ground coff ee for espresso machines and never coff ee beans or instant coff ee.

Note: If no pre-ground coff ee is poured into the compartment, only water will be dispensed.If the dose is excessive and 2 or more measuring scoops of coff ee are used, the machine will not brew the product. Also in this case, the machine will run an empty cycle and discharge any ground coff ee into the coff ee grounds drawer.

MENU OK ESC

22 ENGLISH

To brew coff ee:1 Press and release the “ ” button to select and activate the pre-

ground coff ee function.MENU OK

MENU OK ESC

This page indicates that the function has been activated.

Note: If the brewing is not started within 10 seconds, the machine goes back to the coff ee beans operating mode and displays the symbol.

2 Press and release: The " " button for a cup of espresso

or

the " " button for a cup of long espresso.

MENU OK ESC

3 Lift the pre-ground coff ee compartment lid.

Warning: Add only pre-ground coff ee to the compartment. Other sub-stances and objects may cause severe damages to the machine. Such damages will not be covered by warranty.

Add only 1 scoop of pre-ground coff ee to the compartment. Use only the measuring scoop supplied with the machine to perform this opera-tion. Then, close the lid.

4 Press the " " button. The brewing cycle starts. Once the pre-brewing cycle is complete, coff ee begins to come out of the dispensing spout.

5 Coff ee brewing stops automatically when the set level is reached. However, it is possible to stop the coff ee brewing by pressing the “ ” button.

After brewing the product, the coff ee beans confi guration of the ma-chine is restored.

Note: Repeat the steps described above to brew other coff ees.

Note: If the brewing is not started within 30 seconds after the page is displayed or in case the “ ” button is pressed, the machine returns to the main menu and discharges any inserted coff ee into the coff ee grounds drawer.

MEMO

ESC ESC

INSERT GROUND COFFEE

AND PRESS OK

ENGLISH 23

Brewing Cappuccino

The machine allows brewing cappuccino quickly and easily with the touch of a button.

Danger of scalding! Dispensing may be preceded by small jets of hot water.

Important Note: Immediately after using the Cappuccinatore to froth milk, clean the suction hose externally with a damp cloth. This way, all parts will be perfectly clean and free of any milk residue.

1 Remove the cover from the front side.

Note: The cover can be placed on the machine side using the integrated magnet.

2 Insert the Cappuccinatore into its seat until it locks into place. Check that it cannot slide away.

Warning: Before using the Cappuccinatore, clean it along with the Thermos (if used), as described in the "Cleaning and Maintenance" section.

3 Insert the clean hose (according to your choice)

- in the milk Thermos or - directly in the milk container.

Note: To ensure better results when preparing a cappuccino, use cold milk.

4 Place the cup under the dispensing spout. Press the " " button.

Note: To brew latte macchiato press the “ ” button.

24 ENGLISH

5 The machine needs a preheating time.

6 After preheating, the machine starts brewing the cappuccino.

7 At this stage, the machine dispenses frothed milk. You can stop dis-pensing by pressing the “ ” button.

8 After dispensing milk, the machine brews coff ee. You can stop brewing by pressing the “ ” button.

You can enjoy your cappuccino just like at the coff ee bar.

After using the Cappuccinatore, clean it as described in the "Cleaning the Cappuccinatore" section.Remove the container or Thermos and clean it, if necessary.

Latte Macchiato

The machine allows brewing a latte macchiato quickly and easily with the touch of a button.

To brew a latte macchiato perform all steps for preparing a cappuccino up to step 4.

We recommend using tall glasses for this type of preparation, thus properly moving the dispensing spout.

When the machine is ready, press the " " button to start brewing the latte macchiato.

The machine prepares the latte macchiato automatically.

After using the Cappuccinatore, clean it as described in the "Cleaning the Cappuccinatore" section. Remove the container or Thermos and clean it, if necessary.

CAPPUCCINO

ESC STOP MILK

CAPPUCCINO

ESC STOP COFFEE

ENGLISH 25

Milk Handling

With this machine you can prepare cappuccino, latte macchiato and other milk-based beverage quickly and enjoy your relax time.

You can use either the supplied Thermos or directly the milk container which can be purchase ad your local dealer's shop.

MILK MUST BE USED AND STORED IN ACCORDANCE WITH THE INSTRUC-TIONS GIVEN ON THE MANUFACTURER'S ORIGINAL PACKAGING.WE ACCEPT NO LIABILITY FOR USE OF MILK UNSUITABLE FOR HUMAN CONSUMPTION.

Milk-based beverages can only be prepared if the Cappuccinatore is installed.

Milk Thermos

The machine is supplied with a Thermos specifi cally designed and built to improve milk storage, since it limits the milk temperature increase. The Thermos is only suitable for quick and easy domestic use. It is not recom-mended for continuous, professional-type operation.

To increase storage performance, we recommend fi lling with cold milk (approx. 4°C).

Note: Before using the Thermos, make sure it is thoroughly clean and sanitary. If there is milk left in the Thermos, make sure it is still suitable for food con-sumption before using it.

Do not use the Thermos to heat any beverage other than milk.

The container must be removed at least once a month to allow proper cleaning of all parts. In this way, you can keep a high sanitation level of the brewed beverages. For correct cleaning, refer to the "CLEANING THE THERMOS" section (see pages 40-42).

Warning: Before using the Thermos, clean it as described in the "Cleaning and Maintenance" section.

For correct storage, milk needs to be kept at low temperatures. The Ther-mos allows you to keep milk out of the fridge as long as it is necessary for its correct use.At an ambient temperature of 20°C, the temperature of the milk in the Thermos increases by 4-6°C after 4 hours. Consider this approximate data to determine if milk can still be used in relation to the time it has been stored in the Thermos.

26 ENGLISH

1 Loosen and remove the Thermos lid.

2 Pour milk into the Thermos. Fill in with milk from the MIN level indica-tor and do not exceed the MAX level indicator.

3 Reinsert the Thermos lid by screwing it.

4 Use only the supplied hose to connect the Thermos to the Cappuccina-tore.

This hose features two special fi ttings for optimum operation. The two fi ttings diff er from each other because they have to be properly connected to the Cappuccinatore and the Thermos.

Note: The fi ttings are not interchangeable. If you cannot insert the fi tting in the device, try inserting the other one.

5 Remove the suction tube that is installed in the Cappuccinatore.

ENGLISH 27

6 Insert the hose fi tting in the Thermos.

7 Insert the fi tting in the Cappuccinatore.

The Thermos can now be used to brew milk products.

Milk Container

The milk container can be used directly with the machine to prepare the beverages.

1 For direct use of the milk container it is necessary to use the Cappucci-natore suction tube. This tube only features one fi tting.

2 Check that the tube is inserted in the Cappuccinatore.

Warning: In this case, make sure that the tube is clean on the outside as well, to prevent milk from coming into contact with the dirt on the outside of the tube.

3 Remove the clean suction tube and insert it directly into the container.

Note: After use, remove the tube and wash it properly. Place the container back in the fridge for correct milk storage.

28 ENGLISH

"SPECIAL" Products

The machine is designed to brew other products not displayed on the control panel.

Note: After pressing the “ ” button, if no product is selected, the machine goes back to the main menu after 10 seconds.

1 Press the “ ” button to enter the menu.

2 The display shows the page for "special" beverages.

3 Select the desired beverage by pressing the “ ” or “ ” button.

4 When the desired beverage has been selected, press the “ ” button to start the preparation.

Refer to the relevant section about brewing the desired beverage.Note: If no selection is carried out within 10 seconds, the machine goes back to the home page.

In order to prepare milk-based beverages, install the Cappuccinatore and the Thermos (if necessary) after washing them as described in the "Cleaning and Maintenance" section.

OK ESC


LONG COFFEEHOT MILK

AMERICAN COFFEE


LONG COFFEEHOT MILK

AMERICAN COFFEE

HOT WATER

ESC STOP HOT WATER

Dispensing Hot Water

Dispensing may be preceded by short spurts of hot water. Risk of scalding. The hot water wand may reach high temperatures.



3 Press the “ ” button to start the preparation.

4 After dispensing, remove the container with hot water.

Note: You can stop dispensing by pressing the “ ” button.

ENGLISH 29

Long Coff ee

This programme allows you to prepare a long coff ee.

Note: In this case, you can just prepare one coff ee at a time.


2 Press the " " button to select "LONG COFFEE".

3 Place a suitable cup under the dispensing spout.


5 After brewing, remove the coff ee cup.

Hot Milk

This programme allows you to prepare a hot milk.

Danger of scalding! Dispensing may be preceded by small jets of hot water.

1 Remove the cover from the front side.

2 Insert the complete Cappuccinatore into its seat until it locks into place. Check that it cannot slide away.


- in the milk Thermos or - directly in the milk container.

Note: To ensure better results, use cold milk.


LONG COFFEEHOT MILK

AMERICAN COFFEE

30 ENGLISH


5 Press the " " button to select "HOT MILK".


7 Confi rm by pressing the “ ” button to start the preparation.

Note: You can stop dispensing by pressing the “ ” button.

8 After dispensing, remove the cup with milk.

After using the Cappuccinatore, clean it as described in the "Cleaning the Cappuccinatore" section.Remove the container or Thermos and clean it, if necessary.


LONG COFFEEHOT MILK

AMERICAN COFFEE


LONG COFFEEHOT MILK

AMERICAN COFFEE

American Coff ee

This programme allows preparing and American coff ee.


2 Press the " " button to select "AMERICAN COFFEE".



5 After brewing, remove the coff ee cup.

ENGLISH 31

Beverage Programming

All beverage settings can be customized.

1 Press and hold the “ ” button for 5 seconds to access the machine main menu.

When you enter the programming mode, the buttons have a diff erent function:

“ ” button = “ ” (confi rms a selection or a change you have made)

“ ” button = “ ” (scrolls up the menu)

“ ” button = “ ” (scrolls down the menu)

“ ” button = “ ” (confi rms when you exit a selection)

2 Press the “ ” button to confi rm the selection and enter the “BEVER-AGE MENU”.

This function allows you to set all parameters concerning a beverage brew-ing.

MENU OK

Beverage Parameters

In this case we look at how to programme a customized cappuccino. The milk managing options are not shown when a coff ee brewing (espresso or long coff ee) is being programmed.

Press the “ ” button to select the “CAPPUCCINO” and the “ ” button to enter the menu.

The following describes the diff erent functions.


BEVERAGE MENUESPRESSO

COFFEECAPPUCCINO

LATTE MACCHIATO

BEVERAGE MENULATTE MACCHIATO

SPECIAL BEVERAGESCOUNTERS

BEVERAGE MENUESPRESSO

COFFEECAPPUCCINO

LATTE MACCHIATO

CAPPUCCINOPREBREWING

COFFEE TEMPERATURECOFFEE LENGTHMILK QUANTITY

Dispensed Beverages Counters

This menu enables checking how many products have been brewed.Press the “ ” button until the “COUNTERS” option is selected.

Press the “ ” button to enter the option and display the number of brew-ing procedures performed for each product.

32 ENGLISH

DEFAULT

Default Parameters

For each beverage it is possible to reset the original standard values as-signed by the manufacturer. After selecting this function, the beverage customized settings are deleted.

PREBREWINGPrebrewing: Coff ee is slightly dampened before brewing so as to bring out its full aroma and let it acquire an excellent taste.OFF: prebrewing is not performed.LOW: activated.HIGH: longer in order to bring out the coff ee taste.

COFFEE TEMPERATURE

COFFEE LENGTH

This section allows you to program the temperature for coff ee brewing.LOW: low temperature.NORMAL: standard temperature.HIGH: high temperature.

This section allows programming the amount of coff ee to be brewed for each selected beverage. The strip allows you to determine exactly the amount of coff ee to be brewed.

MILK QUANTITYThis section allows you to program the amount of milk for each selected beverage. The strip allows you to determine exactly the amount of milk to be dispensed.

WATER QUANTITYThis section allows programming the amount of water to be dispensed when pressing the corresponding button. The strip allows determining exactly the amount of water to be dispensed.

Hot Water Parameters (BEVERAGE MENU - >SPECIAL BEVERAGES)

These settings are valid only for programming hot water dispensing.HOT WATERWATER QUANTITY

DEFAULT

ENGLISH 33

Machine Programming

The machine allows you to customize the operating settings.


When you enter the programming mode, the buttons have a diff erent function:

“ ” button = “ ” (confi rms a selection or a change you have made)

“ ” button = “ ” (scrolls up the menu)

“ ” button = “ ” (scrolls down the menu)

“ ” button = “ ” (confi rms when you exit a selection)

2 Press the “ ” button and the “ ” button to confi rm the selection and enter the “MACHINE MENU”.

MENU OK



34 ENGLISH

GENERAL MENU

TONE

CUP-WARM. SURFACE

OFF

OFF

ON

ON

To change the machine operating settings.

This function activates/deactivates the acoustic alarms.

This function allows activating/deactivating the cup-warm-ing surface located on the upper part of the machine.

To deactivate the acoustic alarms

To deactivate the cup-warming surface.

To activate the acoustic alarms

To activate the cup-warming surface.

ECOMODE

OFF

ON

This function enables activating the boilers on the machine to allow saving energy.

This way, only the coff ee boiler is activated at machine start-up. The machine saves energy but needs longer time to dispense milk-based bever-ages.

This function activates all the boilers at every ma-chine start-up to be immediately able to prepare all kinds of beverages. The power consumption is higher this way, because the machine is always ready for use.

15 MINUTES

30 MINUTES

60 MINUTES

180 MINUTES

STAND-BY SETTINGSTo set the time interval for the machine to go into stand-by mode after the last brewing. The default time value is «after 30 minutes».

Once the set time has elapsed, the machine goes into stand-by mode. Press any button to turn the machine on again. After performing the function diagnostics and the warm-up phase, the machine is again ready for use.

General Menu

ENGLISH 35

DISPLAY MENU

LANGUAGE

CONTRAST

BRIGHTNESS

ENGLISH

This menu allows you to set the menu language and the display brightness.

This setting is of fundamental importance for correctly adjusting the parameters of the machine according to the country where the machine is used.

To set the correct display contrast according to the room illumination.

To set the correct display brightness according to the room illumination.

The currently selected language is displayed. The language can be changed with the special controls.

Display Menu

WATER MENU

HARDNESS

ENABLE FILTER

ACTIVATE FILTER

This menu allows setting correct water parameters for coff ee brewing.

To change the machine water hardness setting.With the "Hardness" function you can adjust your machine to the level of hardness of the water you use, so that the machine will request descaling at the right moment.Measure water hardness as shown on page 12.

To activate/deactivate the warning signal to replace the water fi lter. By activating this function, the machine notifi es the user when the water fi lter needs to be replaced.OFF: Warning disabled.ON: Warning enabled (this value is automatically set when the fi lter is activated).

To activate the fi lter after its installation or replacement. Refer to the relevant section on page 14 to correctly install and/or replace the fi lter.

Water Menu

36 ENGLISH

MAINTENANCE

DESCALING

CAPPUCCINATORE CLEAN

BREW GROUP CLEAN

FACTORY SETTINGS

This menu allows setting all the functions for correct machine mainte-nance

This function enables the descaling cycle (the machine shows how many litres can be dispensed before descaling) (see page 50).

This function enables the wash cycle for the Cappuccinatore used to prepare milk-based beverages (see page 42).

Note: This wash cycle is fundamental for a correct mainte-nance of the Cappuccinatore.

This function allows you to perform the wash cycle for the Brew Group (see page 45).

This function allows restoring all factory settings. Note: By restoring the factory settings, all the personal parameters get lost.

Maintenance

Factory Settings

ENGLISH 37

Cleaning and Maintenance

As some of the parts of your appliance come in contact with water and cof-fee during normal use, it is important that you clean your appliance regu-larly. This is an easy procedure with your Philips-Saeco Espresso machine. Just follow the steps indicated on the display and described below.Not doing this will ultimately make your appliance stop working properly, and in this case repair is not covered under your warranty.

General Cleaning

1 Empty and clean the drip tray and the coff ee grounds drawer daily, with the machine turned on.

Note: We recommend cleaning the fl oat and its seat to ensure perfect opera-tion.

Note: Other maintenance and cleaning operations can only be carried out when the machine is cold and disconnected from the electrical network.

Do not immerse the machine in water.Do not wash any of its parts in the dishwasher.Do not use sharp objects or harsh chemical products (solvents) for clean-ing.Use a soft, dampened cloth to clean the machine.Do not dry the machine and/or its parts using a microwave and/or stand-ard oven.

2 It is recommended to clean the water tank daily:- Remove the "INTENZA+" water fi lter (or remove the small white

fi lter if you have not yet installed the "INTENZA+" water fi lter) from the water tank and wash it under running drinking water;

- Reposition the "INTENZA+" water fi lter (or the small white fi lter if you have not yet installed the "INTENZA+" water fi lter) in its hous-ing by gently pressing and turning it at the same time;

- Fill the water tank with fresh drinking water.

3 Empty and clean the drip tray daily. Perform this operation also when the fl oat is raised.

38 ENGLISH

4 If you use the pre-ground coff ee compartment, clean it every week with the supplied brush.

Cleaning the Cappuccinatore (After Each Use)

The Cappuccinatore must be washed and cleaned every time it is used.

The lack of cleaning before and after each use can aff ect the correct opera-tion of the machine.

For a quick cleaning, proceed as follows:

1 Make sure the Cappuccinatore complete with all its parts is correctly inserted.

2 Insert the suction hose in a carafe containing clean water.

3 Place a container under the dispensing spout.

4 With the machine on, press the " " button.

The machine performs a wash cycle of the Cappuccinatore.

Wait until the cycle stops automatically.

5 Push the buttons located on the sides and remove the Cappuccinatore.

ENGLISH 39

6 Place the cover back on the machine.

Important Note: We recommend removing the Cappuccinatore when not be-ing used, in order to keep it clean.

7 Remove the suction tube from the Cappuccinatore.

8 Remove the ring from the Cappuccinatore.

9 Rotate and lift the Cappuccinatore cover and remove it from the Cap-puccinatore body.

10 Remove the Cappuccinatore internal fi tting.

11 Remove the suction tube joint from the Cappuccinatore.

12

40 ENGLISH

Day Cleaning - Thermos

The Thermos has to be cleaned every day to ensure proper operation.

Note: To clean the Thermos, the Cappuccinatore has to be installed. You can take the occasion to perform the daily cleaning of the Cappuccinatore at the same time.

1 Rotate the lid and open the Thermos.

12 Wash the parts under running water.

Make sure any possible milk deposits/residues are removed.

After washing, reassemble the parts following the same procedure used for disassembly, but in reverse order.

2 Remove the internal tube installed in the Thermos lid. Wash it under lukewarm running water.

3 Wash the Thermos lid with the tube inserted; in particular, wash the internal sealing of the lid thoroughly.

After washing the Thermos lid, install the previously removed tube. Without this tube, milk cannot be frothed.

ENGLISH 41

4 Wash the inside of the Thermos under lukewarm running water.

Make sure any possible milk deposits/residues are removed.

5 Fill the Thermos with fresh water and close the lid.

6 Connect the Thermos to the Cappuccinatore.

7 Place a container under the dispensing spout.

8 With the machine on, press the " " button.

The machine performs a wash cycle of the Cappuccinatore.


The wash cycle is now complete.

Refer to the following section for a thorough cleaning.

42 ENGLISH

Monthly Cleaning - Cappuccinatore + Thermos (Thorough Cleaning)

Clean all the Cappuccinatore and Thermos parts thoroughly every month using the Saeco detergent supplied with the machine. The Saeco deter-gent may be purchased at your local dealer, at the Philips on-line shop at http://shop.philips.com or at authorised service centres.

The lack of cleaning before and after each use can aff ect the correct opera-tion of the machine.

1 Make sure the Cappuccinatore is correctly placed.

2 Press and hold the “ ” button for 5 seconds to enter the machine main menu.

3 Press the “ ” button and select the “MACHINE MENU” option; press the “ ” button to enter the menu.

4 Press the “ ” button and select the “MAINTENANCE” option; press the “ ” button to enter the menu.

5 Press the " " button until the "CAPPUCCINATORE CLEANING" option can be selected. Press the " " button to confi rm.

6 Press the “ ” button to start the cleaning cycle of the Cappuccinatore.

Note: If this option is confi rmed, the cycle must be completed. Press the “ ” button to exit.

7 Fill the water tank and press the “ ” button to confi rm.

MAINTENANCEBREW GROUP CLEAN

DESCALINGCAPPUCCINATORE CLEANING

WASH THECAPPUCCINATORE?

CAPPUCCINATORE CLEANING

REFILLWATER TANK


ENGLISH 43


- in the Thermos or - directly in the container.


Drinking the solution dispensed during this procedure is strictly forbidden. The solution must be disposed of.

8 Pour a solution bag in the Thermos or in a container with 1/2 (a half ) litre of fresh drinking water.

9 Wait for the bag content to dissolve completely and then press the “ ” button to confi rm.

12 Place an empty container of at least 1 litre capacity under the dispens-ing spout and press the “ ” button to confi rm.

13 The machine performs a wash cycle of the Cappuccinatore.

The bar shows the washing progress.


POUR DETERGENTIN A CONTAINER

WITH 1/2 L WATER


PUT CAPPUCCINATOREHOSE IN THECONTAINER



DISPENSING SPOUT



44 ENGLISH


15 Carefully wash:

- the Thermos or - the container.

used for the solution and fi ll it with 1/2 (a half ) litre of fresh drinking water that will be used for rinsing.

Empty the container placed under the dispensing spout.

16 Insert the suction hose in the used container.

Press the " " button to confi rm.

17 Place an empty container under the dispensing spout and press the “” button to confi rm.

18 The machine performs a rinse cycle of the Cappuccinatore.

The bar shows the rinsing progress.

Wait until the cycle stops automatically. The machine will go back to the normal operating cycle.

19 Push the buttons located on the sides and remove the Cappuccinatore.

20 Wash all the Cappuccinatore parts, as described on page 39.

21 Wash all the Thermos parts (if the Thermos has been used), as de-scribed on page 40.

Important Note: We recommend removing the Cappuccinatore when not be-ing used, in order to keep it clean.

REFILLWATER TANK


INSERT CAPPUCCINATOREHOSE IN A CONTAINER

WITH 1/2 L WATER



DISPENSING SPOUT



ENGLISH 45

Brew Group

Weekly Cleaning - Brew Group

The brew group should be cleaned every time the coff ee bean hopper is fi lled or at least once a week.

1 Turn off the machine by pressing the power button and remove the plug from the socket.

2 Remove the drip tray and the coff ee grounds drawer.

Open the service door:

1) Rotate the lever clockwise by 90°; 2) Pull the door towards you.

1

2

3 Remove the brew group: Pull it by the handle and press the «PRESS» button. The brew group must be washed only with lukewarm water with no detergent.

4 Wash the brew group with lukewarm water and carefully wash the upper fi lter. Before placing the Brew Group in its housing, make sure there is no water left in the brewing chamber.

5 Lift the rear part of the inner tray and unlock it.

6 Remove the inner tray, wash and reposition it in its seat.

Note: When inserting the tray follow the same procedure used for disassembly, but in reverse order.

46 ENGLISH

7 Make sure the Brew Group is in the rest position; the two reference signs must match.

If they do no match, proceed as described in step (8).

10 Insert the Brew Group in its seat again until it locks into place WITHOUT pressing the "PRESS" button.

8 Make sure that the lever is in contact with the brew group base.

11 Insert the coff ee grounds drawer and the drip tray. Close the service door.

9 Make sure that the hook to lock the Brew Group is in the correct posi-tion; to check its position fi rmly press the "PRESS" button.

ENGLISH 47

Brew Group Cleaning with "Coff ee Clean Tablets":

Besides weekly cleaning, we recommend running the cleaning cycle with "Coff ee Clean Tablets" after approximately 500 cups of coff ee or once a month. This operation completes the maintenance process of the brew group.The "Coff ee Clean Tablets" to clean the Brew Group and the "Maintenance Kit" may be purchased at your local dealer, at the Philips on-line shop at http://shop.philips.com or at authorised service centres.

Warning: The "Coff ee Clean Tablets" has no descaling property. For descal-ing use the Saeco descaling solution and follow the procedure described in the "Descaling" chapter.

The wash cycle cannot be stopped.Do not leave the machine unattended during this operation.

1 Press and hold the “ ” button for 5 seconds to enter the machine main menu.




5 Press the “ ” button to start the cleaning cycle of the brew group.

Note: If this option is confi rmed the cycle must be completed. Press the “ ” button to exit.




PERFORM BREW GROUP CLEANING?

BREW GROUP CLEAN

REFILLWATER TANK

BREW GROUP CLEAN

48 ENGLISH

8 Place a container under the dispensing spout and press the “ ” but-ton to confi rm.

9 The machine completes the cycle automatically.

Note: Once the cycle is complete, the machine goes back to its normal operat-ing mode.

Brew Group Lubrication

Lubricate the Brew Group after approximately 500 cups of coff ee or once a month. The grease to lubricate the Brew Group and the complete "Service Kit" may be purchased at your local dealer, at the Philips on-line shop at http://shop.philips.com or at authorised service centres.

Note: To display the number of coff ee cups brewed, please refer to the "COUN-TERS" menu in the "BEVERAGE PROGRAMMING" menu.

Before lubricating the brew group clean it under running water as described in the chapter “Brew Group - Weekly Cleaning”.

7 Insert the cleaning tablet into the pre-ground coff ee compartment and press the “ ” button to confi rm.


DISPENSING SPOUT

BREW GROUP CLEAN

BREW GROUP CLEAN

INSERT GROUPCLEAN TAB

BREW GROUP CLEAN

ENGLISH 49

1 Lubricate the brew group guides using the Saeco grease only. Apply the grease evenly on both side guides.

2 Lubricate also the shaft.

3 Insert the Brew Group in its seat again until it locks into place WITHOUT pressing the "PRESS" button.

Note: the detailed instructions to prepare the brew group and insert it correctly in the machine can be found on page 46 (point 7, 8, 9 and 10) of the section “Brew Group - Weekly Cleaning”.

4 Insert the coff ee grounds drawer and the drip tray. Close the service door.

50 ENGLISH

Descaling

Limescale is a natural part of the water used for the machine operation. It needs to be removed regularly as it may clog the water and coff ee circuit of your appliance.This is an easy procedure with your Philips-Saeco machine.The advanced electronics tells you on the display of the machine (in clear symbols) when descaling is needed. Just follow the steps described below.

Not doing this will ultimately make your appliance stop working properly, and in this case repair is not covered under your warranty.

Use the Saeco descaling product only. Its formula has been designed to ensure better machine performance and operation for its whole operating life. If correctly used, it also avoids alterations in the brewed product. The descaling solution and the complete "Maintenance Kit" may be purchased at your local dealer, at the Philips on-line shop at http://shop.philips.com or at authorised service centres.

Warning! Never drink the descaling solution or any products dispensed until the cycle has been carried out to the end. Never use vinegar as a descaling solution.

1 Turn on the machine by pressing the ON/OFF button. Wait for the machine to fi nish its rinse and warm-up process.

Warning! Remove the "Intenza" fi lter before adding the descaling solution.




5 Press the “ ” button and select the “DESCALING” option; press the “ ” button to enter the menu.



ENGLISH 51

7 Pour the entire content of the Saeco concentrated descaling solution into the water tank and then fi ll the tank with fresh drinking water up to the level indicated by the icon.

Place the tank back in the machine. Press the " " button.

9 Insert the complete Cappuccinatore into the machine and remove the dispensing spout.

Press the " " button.

Note: Keep the suction tube removed from the Cappuccinatore while the descaling cycle is performed.

6 Press the “ ” button to start the DESCALING cycle.

Note: If this option is confi rmed, the rest of the cycle must be completed. Press the “ ” button to exit.

8 Remove any liquids from the drip tray and insert it back into the ma-chine.


START DESCALING?

DESCALING

FILL TANK WITH DESCALING SOLUTION

DESCALING

EMPTY DRIP TRAY

DESCALING

INSERT THECAPPUCCINATORE WITHALL THE COMPONENTS

DESCALING

52 ENGLISH

10 Place a container under the hot water wand and a large enough con-tainer under the Cappuccinatore.


Note: Use a container of at least 1.5 litre capacity. If you do not have a container of this capacity, pause the cycle by pressing the “ ” button, empty the container, place it back in the machine and restart the cycle by pressing the “ ” button.

11 At this point the machine will start dispensing the descaling solution at intervals (the bar shows the cycle progress).

12 When the solution in the tank is fi nished, the machine requests to empty and rinse the tank with fresh drinking water.

13 Rinse the water tank thoroughly and refi ll it with fresh drinking water.

Insert the tank into the machine. Press the “ ” button.

14 Empty the containers used to collect the liquid dispensed by the ma-chine.

15 Remove any liquids from the drip tray and insert it back.


16 Check that the Cappuccinatore is placed in the machine.


17 Place a container under the hot water wand and a large enough con-tainer under the Cappuccinatore.


EMPTY DRIP TRAY

DESCALING

INSERT THECAPPUCCINATORE WITHALL THE COMPONENTS

DESCALING

PLACE A CONTAINERUNDER MILK AND HOTWATER DISPENSERS

DESCALING

RINSE TANK &FILL WITH WATER

DESCALING

PLACE A CONTAINERUNDER MILK AND HOTWATER DISPENSERS

DESCALING

STEP 1/2

DESCALING

PAUSE

ENGLISH 53

18 The machine performs the rinse cycle.

Note: A default amount of water is needed for the rinse phase. This allows performing an ideal rinse cycle to ensure the best conditions to brew products. The message about fi lling the tank for the rinse cycle is normal, as it is part of the procedure.

Note: The rinse cycle may be paused by pressing the “ ” button. To resume the cycle, press the “ ” button again. This allows you to empty the container or to go away for a short period of time.

19 Once the rinse cycle is complete, the machine carries out the warm-up and rinse cycle to prepare for product brewing.

20 Empty the containers used to collect the liquid dispensed by the ma-chine and reassemble the dispensing spout.

21 The machine is now ready for use.

Note: - The descaling solution must be disposed of according to the manufac-

turer's instructions and/or regulations in force in the country of use. - After completing the descaling cycle:

1 Wash the brew group as described in the “Brew Group” section in the “Cleaning and Maintenance” chapter;

2 Rinse the Cappuccinatore under running water.

When the descaling cycle is complete, we recommend emptying the drip tray.

STEP 2/2

DESCALING

PAUSE

54 ENGLISH

Help Message Displayed How to Reset the Message

CLOSESIDE DOOR

To restore the machine operation, close the service door.

INSERT DRIP TRAYInsert the drip tray.

INSERT COFFEEGROUNDS DRAWER

Insert the coff ee grounds drawer.

CLOSEHOPPER DOOR

Close or correctly place the coff ee bean hopper inner lid to be able to prepare any product.

REFILLWATER TANK

Remove the tank and fi ll it with fresh drinking water or top it up by means of the corresponding opening.

INSERT BREW GROUP

Insert the Brew Group into its seat.

INSERTCAPPUCCINATORE

An operation has been selected that requires dispensing milk. Insert the Cappuccinatore in the machine as specifi ed in the manual.

INSERT VALVE INTOCAPPUCCINATORE

An operation has been selected that requires dispensing milk. Insert the valve in the Cappuccinatore as described in the manual (see step 10 on page 39).

ADD COFFEE

Fill the coff ee bean hopper with coff ee beans.

LCD Display Warnings

ENGLISH 55

Help Message Displayed How to Reset the Message

The machine requests a descaling cycle.When this message is displayed, it is still possible to use the ma-chine, but its correct operation might be aff ected.Damages caused by failure to descale the machine are not cov-ered by warranty.

The machine requests the "Intenza" water fi lter to be replaced with a new one. Replace the fi lter as described on page 14.

The alarm is displayed only if the "Enable Filter" function is set to "ON". (see page 35).

The machine reminds that after a few cycles it will be necessary to empty the coff ee grounds drawer. This message does not prevent the machine from brewing some more products.

EMPTY COFFEE GROUNDS DRAWER

Remove the coff ee grounds drawer and empty the coff ee grounds into a suitable container.Note: The coff ee grounds drawer must be emptied only when the machine asks for it and with the machine turned on. If you empty the drawer with the machine turned off it will not record the emptying operation.Blinking red light. Machine in Stand-by.

The Stand-by settings can be changed

Press the " " button

RESTART TO SOLVE

An event has occurred which needs the machine to be restarted. Take note of the code (E xx) shown at the bottom.Turn off the machine, wait for 30 seconds and then turn it on again. If the problem persists, contact the service centre.

DESCALINGNEEDED.

DESCALE?

DESCALING If this page is displayed after starting the machine, this means that the descaling cycle is needed.Press the " " button to enter the descaling menu and refer to the relevant section.Press the " " button to go on using the machine.We remind you that damages caused by failure to descale the machine are not covered by warranty.

56 ENGLISH

Machine actions Causes SolutionsThe machine does not switch on.

The machine is not connected to the electric network.

Connect the machine to the electric network.

Coff ee is not hot enough. The cups are cold. Preheat the cups with hot water.Cup-warming surface deactivated Activate the cup-warming surface and

wait for the cups to warm.Coff ee has not enough crema.(See note)

The blend is unsuitable, coff ee is not freshly roasted or the grind is too coarse.

Change coff ee blend or adjust the grind as explained in section "Adjusting the Coff ee Grinder".

The machine takes a long time to warm up or the amount of water dispensed from the wand is too little.

The machine circuit is clogged by limescale.

Descale the machine.

Bubbles form at the Cappucci-natore spout while dispensing milk.

The tube fi ttings are not connected properly or are not completely inserted in the Cappuccinatore and/or Thermos.

Insert the suction tube completely in the Cappuccinatore and/or Thermos (if used).

Steam comes out of the Cap-puccinatore when the Thermos is connected and/or when sucking milk.

There is no milk in the Thermos and/or container any more.

Check for milk presence. If necessary, fi ll in the Thermos again or replace the milk container with a new one.

Thermos internal tube is not present. Install the tube in the Thermos lid.The Brew Group cannot be removed.

The Brew Group is out of place. Turn the machine on. Close the service door. The brew group automatically returns to the initial position.

The coff ee grounds drawer is inserted.

Remove the coff ee grounds drawer before removing the brew group.

The machine grinds the coff ee beans but no coff ee comes out.(See note)

The Brew Group is dirty. Clean the Brew Group ("Brew Group" section).

The dispensing spout is dirty. Clean the dispensing spout.Coff ee is too weak.(See note)

Too low dose Adjust the amount of coff ee to be ground.

Coff ee is brewed slowly.(See note)

The coff ee grind is too fi ne. Change coff ee blend or adjust the grind as explained in section "Adjusting the Coff ee Grinder".

The Brew Group is dirty. Clean the Brew Group ("Brew Group" section).

Coff ee leaks out of the dispens-ing spout.

The dispensing spout is clogged. Clean the dispensing spout and its holes.

Note: These problems can be considered normal if the coff ee blend has been changed or if the machine has just been installed.

Please, contact our consumer care help line at the phone number listed at the last page of this document for any problems not covered in the above table or when the suggested solutions do not solve the pro-blem.

Troubleshooting

Disposal

- The packing materials can be recycled.- Appliance: Unplug the appliance and cut the power cord.- Deliver the appliance and power cord to a service center or public waste disposal facility.

This product complies with eu directive 2002/96/ec.

The symbol

on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city offi ce, your household waste disposal service or the shop where you purchased the product.

Technical Specifi cations

The manufacturer reserves the right to make changes to the technical specifi cations of the product.

Nominal voltage - Power rating - Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See label on the inside of the service door

Housing material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Thermoplastic material / Metal

Size (w x h x d) (mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336 x 380 x 450

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 kg

Power cord length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 m

Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . On the front

Cappuccinatore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Special for cappuccino

Water tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.2 litres - Removable type

Coff ee bean hopper capacity (g) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .320

Coff ee grounds drawer capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Pump pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 bar

Boiler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stainless steel type

Safety devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Thermal fuse

Service

We want to ensure that you remain satisfi ed with your Philips Saeco Es-presso coff ee machine.If not done already, please register your purchase on "www.philips.com/welcome" so that we can stay in contact with you and send you cleaning and descaling reminders.

For cleaning and descaling, use SAECO products only. You can purchase these on-line at the Philips on-line shop at:

• NL http://shop.philips.nl

• BE http://shop.philips.be

• FR http://shop.philips.fr

• DK http://shop.philips.dk

• DE http://shop.philips.de

• ES http://shop.philips.es or http://tienda.philips.es

• IT http://shop.philips.it

• SE http://shop.philips.se

If you have questions about your appliance, e.g. about its installation, use, cleaning or descaling, please refer to this user manual or go for the latest updates to www.philips.com/support.

Alternatively, you may contact our toll free consumer care help line at the phone number listed on the last page of this document.

Our qualifi ed service staff will help you and, if needed, trouble shoot your appliance by phone and where possible provide a solution during the call. If this is not possible we will help you to initiate any necessary repair in the shortest possible time and with maximum convenience.

CONSUMER RELATIONS DESKSFor Downloads & FAQs visit our Customer Support Website: www.philips.com/support

Argentina: 0800-888-7532 (toll free)Australia: 1300 363 391 (toll free)Bahrain: +973 17700424Belgium: 0800 80 190 (toll free)Brazil: 0800 701 0203 (other areas) (11) 2121 0203 (San Paolo)Bulgaria: 00 800 11 544 24 (toll free)Canada: (Montreal) - 1-514-385-5551 (Toronto) - 1-416-256-9191 (Vancouver) - 1-604-299-7555 Czech Republic: 800 142840China: 4008 800 008Croatia: 0800 222 778Denmark: 3525 8759Germany: 0800 000 7520 (toll free)Spain: 902 199 742Estonia: 8000100288France: 0805025510 (toll free)Greece: 0 0800 3122 1280 (toll free)Hong Kong: 852 2619 9663Israel: 03-6458844Iran: +98 21 2227 9353Ireland: 18007445477 (toll free)Italy: 800 233 793 (toll free)Korea: 080-600 6600 (toll free)Kuwait: 1 80 35 35. Latvia: 80002794Lebanon: 961 1 684900Lithuania: 880030483Luxembourg: 0800 26 550Hungary: 06 80 018 189 Malaysia: 1800 880 180The Netherlands: 0800 023 0076 (toll free)Norway: 2270 8111Austria: 0800 180 016 (toll free)Poland: 00800 3111318Portugal: 800 780 903 (toll free)Romania: 0800-894910 (available for free from the Romtelecom network)Russia: +7 495 961-1111 - 8 800 200-0880Singapore: +65 68823999 Slovenia: 080080254Slovak Republic: 0800 004537 (toll free)Finland: (09) 2311 3415South Africa: 08611-72326Sweden: 0857929100Switzerland: 0800 002 050 (toll free)Ukraine: 0-800-500-697United Arab Emirates (Dubai): +971 4 2310300United Kingdom: 08003316015 (toll free)USA: 800.933.7876 (toll free)Taiwan: 0800 231099Thailand: +6626528652

The manufacturer reserves the right to make changes without prior notice.

EN0

2

02

Re

v.0

3

de

l 29

-07-

11

www.philips.com/saeco

Documents

02-15002770-New Royal-EN-03.indd - Seattle Coffee Gear