01 Machines

1

Weldmax 2

Fronius 6

Cebora 23

Unimig 37

Hypertherm 40

Proarc Positioners 47

Kemper Fume Extraction 54

Pilot Air Compressors 58

Welder Generators 61

TIG Brush Cleaning System 63

MachinesSection One

2S

EC

TIO

N O

NE

– M

AC

HIN

ES

WEldMAx 255 & 255S

PART NUMBER: WMXT255

PART NUMBER: WMXT255S

The Weldmax 255 & 255S are a single phase (multi voltage) power source suited to medium level workshops.

Ideally, these machines are suitable for light-medium fabrication & maintenance applications.

FEATURESGeared Drive & Pressure Rollers•14 Voltage Settings•Euro Torch Connection•8m Interconnecting Leads On SWF •ModelsOvertemp Protection•Reverse Polarity For Gas or Gasless •WireTrigger Catch, Spot & Stitch Control•Fan Cooled•5 Year Transformer & Choke Warranty•2 Year PCB & Rectifier Warranty•1 Year Warranty On Most Other •Components

SPECIFICATIONS

Duty Cycle Rating250amp @ 30%•175amp @ 60%•135amp @ 100%•

Tested Over 4 Hour CycleWire Sizes:Hard Wire

0.6 / 0.8mm V0.9 / 1.0mm V1.0 / 1.2mm V

Soft Wire0.9 / 1.0mm U1.0 / 1.2mm U1.2 / 1.6mm U

Cored Wire0.9 / 1.0mm Knurled1.2 / 1.6mm Knurled

DimensionsCompact 63kg 830l x 410w x 830hSWF Model 76kg 810l x 410w x 620h

PART NUMBER: WMX270

PART NUMBER: WMX270S

The Weldmax 270 & 270S single phase machines fit into the professional and industrial sector.These mig welders are especially sought after models suitable for light to heavy fabrication, farm work and construction sites where optimum performance is essential on 240v supply.

FEATURESGeared Drive & Pressure Rollers•30-290amps Welding Range•21 Voltage Settings•10m Interconnecting Leads on SWF2 •Models25% Bigger Transformer than most •other conventional mig weldersCopper Wound Transformers•Overtemp Protection•Reverse Polarity For Gas or Gasless •WireTrigger Latch, Switch & Spot Control•Fan Cooled•5 Year Transformer & Choke Warranty•2 Year PCB & Rectifier Warranty•1 Year Warranty On Most Other •Components

SPECIFICATIONS



0.6 / 0.8mm V0.9 / 1.0mm V1.0 / 1.2mm V

Soft Wire0.9 / 1.0mm U 1.2 / 1.6mm U


DimensionsCompact 113kg 985l x 390w x 745h Excluding wheelsSWF2 136kg (inc PS & SWF)

WEldMAx 270 & 270S

3S

EC

TIO

N O

NE

– MA

CH

INE

S

WEldMAx 335 & 335S

PART NUMBER: WMX290


The Weldmax 290 & 290S mig machines are the largest and most power effective in their range.

Boasting 290amp output from a 240v, 15amp primary supply, enables large tasks to be accomplished in remote areas or where three phase power is unaccessable.

FEATURESGeared Drive & Pressure Rollers•30-320amps Welding Range•21 Voltage Settings•Euro Torch Connection•10m Interconnecting Leads on SWF2 •Models25% Bigger Transformer than most •other conventional mig weldersCopper Wound Transformers•Overtemp Protection•Reverse Polarity For Gas or Gasless •WireTrigger Latch, Switch & Spot Control•Fan Cooled•5 Year Transformer & Choke Warranty•2 Year PCB & Rectifier Warranty•1 Year Warranty On Most Other •Components

SPECIFICATIONS



0.6 / 0.8mm V0.9 / 1.0mm V1.0 / 1.2mm V

Soft Wire0.9 / 1.0mm U 1.2 / 1.6mm U


DimensionsCompact 116kg 985l x 390w x 745h Excluding wheelsSWF2 139kg

PART NUMBER: WMXT335

PART NUMBER: WMXT335S

The Weldmax 335 & 335S are designed & built to cater for heavier fabrication and maintenance applications where performance and finish is a priority. These machines offer exceptional welding characteristics, on a wide range of materials.

FEATURESGeared Drive & Pressure Rollers•20 Voltage Settings•Euro Torch Connection•8m Interconnecting Leads On SWF •ModelsOvertemp Protection•Reverse Polarity For Gas or Gasless •WireFan Cooled•5 Year Transformer & Choke Warranty•2 Year PCB & Rectifier Warranty•1 Year Warranty On Most Other •Components

SPECIFICATIONS



0.6 / 0.8mm V0.9 / 1.0mm V1.0 / 1.2mm V

Soft Wire0.9 / 1.0mm U 1.2 / 1.6mm U


DimensionsCompact 77kg 830l x 410w x 890hSWF Model 87kg 810l x 410w x 620h

WEldMAx 290 & 290S

4S

EC

TIO

N O

NE

– M

AC

HIN

ES

WEldMAx 350 & 350S

PART NUMBER: WMX350


The Weldmax 350 & 350S mig welding machines offer excellent arc characteristics & unsurpassed value. They are perfect for all materials and can perform difficult tasks with ease. The 350 range is the answer for those who require smooth, low spatter welding on all tasks from sheetmetal to heavy fabrications.

FEATURESGeared Drive & Pressure Rollers•30-380amps Welding Range•30 Voltage Settings•Euro Torch Connection•10m Interconnecting Leads on SWF2 •Models25% Bigger Transformer than most •other conventional mig weldersCopper Wound Transformers•Overtemp Protection•Reverse Polarity For Gas or Gasless •WireTrigger Latch, Switch & Spot Control•Fan Cooled •5 Year Transformer & Choke Warranty•2 Year PCB & Rectifier Warranty•1 Year Warranty On Most Other •Components

SPECIFICATIONS

Duty Cycle Rating335amp @ 60%•260amp @ 100%•


0.6 / 0.8mm V0.9 / 1.0mm V1.2 / 1.6mm V

Soft Wire0.9 / 1.0mm U 1.2 / 1.6mm U


DimensionsCompact 140kg 985l x 450w x 745h Excluding wheelsSWF2 164kg 1000l x 560w x 900h

WEldMAx 395 & 395S

PART NUMBER: WMX395


The Weldmax 395 & 395S are designed for professionals who expect superior performance from their welding equipment. The 395 range provides consistent welding with clean and crisp characteristics on a wide range of materials, including mild steel, stainless steel & aluminium.

FEATURESGeared Drive & Pressure Rollers•30-410amps Welding Range•30 Voltage Settings•Euro Torch Connection•10m Interconnecting Leads on SWF2 •Models25% Bigger Transformer than most •other conventional mig weldersCopper Wound Transformers•Overtemp Protection•Reverse Polarity For Gas or Gasless •WireFan Cooled •Trigger Latch, Switch & Spot Control•5 Year Transformer & Choke Warranty•2 Year PCB & Rectifier Warranty•1 Year Warranty On Most Other •Components

SPECIFICATIONS



0.6 / 0.8mm V0.9 / 1.0mm V1.0 / 1.2mm V1.2 / 1.6mm V

Soft Wire0.9 / 1.0mm U 1.2 / 1.6mm U


DimensionsCompact 144kg 985l x 450w x 745h Excluding wheelsSWF2 168kg

5S

EC

TIO

N O

NE

– MA

CH

INE

SWEldMAx 440S


The Weldmax 440S is a professional quality, high performance mig welder suited to heavy industrial/fabrication workshops needing high endurance and output. It offers a heavy duty 4WD wire feed system coupled to outstanding arc quality.

FEATURES4x Geared Drive & Pressure Rollers•30-450amps Welding Range•30 Voltage Settings•Euro Torch Connection•10m Interconnecting Leads on SWF2 •Models25% Bigger Transformer than most •other conventional mig weldersCopper Wound Transformers•Overtemp Protection•Reverse Polarity For Gas or Gasless •WireFan Cooled •Trigger Latch, Switch & Spot Control•5 Year Transformer & Choke Warranty•2 Year PCB & Rectifier Warranty•1 Year Warranty On Most Other •Components

SPECIFICATIONS



0.6 / 0.8mm V0.9 / 1.0mm V1.0 / 1.2mm V1.2 / 1.6mm V

Soft Wire0.9 / 1.0mm U1.2 / 1.6mm U


DimensionsSWF2 182kg 985l x 450w x 660h

6S

EC

TIO

N O

NE

– M

AC

HIN

ES

“Synergic mode” meaning a very special skill boasted by the fully digitised MIG / MAG machines from Fronius. These pulsed-arc power sources are jam packed with knowledge. The only thing left for you to do is set the wire diameter and type of material, and the machine will take care of all the other parameters by itself, Automatically. Optimum results time after time, no matter whether you’re working with steel, stainless steel or even aluminium. With a power range that goes all the way from 270 up to 500 amps. This is a knowledged-packed skilled worker that you should be out to recruit.

Custom built systems, such as 36 inch orbital pipe tracking vehicles and high deposition welding packs up 1800 amps have been supplied throughout the world for customers that require a technological edge. Forward thinking is our specialty.

7S

EC

TIO

N O

NE

– MA

CH

INE

S

FRONIUS TRANSSYNERGIC 4000/5000

PN: VS4000 4.025.203

PN: VS5000 4.025.204

This sturdy step controlled MIG/MAG machine has integrated microprocessor program technology. It is a balanced cost/benefit ratio for those who work with sheet metal, machine and apparatus engineering & heavy structural steel.

FEATURESWater cooler compatible•2 step, 4 step, spot and intermittent •weldingWire inch without gas or current•

PN: TS4000 4.075.097

PN: TS5000 4.075.098

FRONIUS VARIO SYNERGIC 4000-2/5000-2

Gas pre-flow adjustable•Gas post-flow adjustable•4 roller drive•Thermostat-controlled fan•Super quiet•Over current protection•Over temperature indicator•Digital ammeter•Digital volt meter•Digital read-out of material guideline •valueDigital read-out of wire feed speed•Digital inductance-tap read out•Automatic soft start•Automatic burn back•Error code read out•20 welding programs•Generator compatible•

SPECIFICATIONS

Duty Cycle RatingsVS4000

400 Amps @ 35%•290 Amps @ 60%•220 Amps @ 100%•

VS5000500 Amps @ 30%•360 Amps @ 60%•280 Amps @ 100%•

Wire Sizes:Hard Wire

0.8mm 0.9mm 1.0mm 1.2mm 1.6mm

Soft Wire 0.9mm 1.0mm 1.2mm 1.6mm

Cored Wire 1.2mm 1.6mm 2.0mm

Dimensions (wheels attached)890 x 460 x 945 mm VS4000 & VS5000PS Weight VS4000 148kgPS Weight VS5000 156kg

The Fronius Transsynergic 4000/5000 MIG welders are ideal for structural steel, shipyards, offshore, apparatus construction, mechanical engineering and tank manufacturing. These welding units have superb welding properties and are light weight inverter based power sources.

FEATURESDigital welding process control•Continuous adjustable•4 roller drive•Serial interface for data transmission•MIG brazing of galvanized sheets•Synergic programs•TIG lift arc ignition & MMA•Very easy to use•Digital display for amps, volts, material •thickness, wire speed, inductance, arc lengths etcRemote controllable•Modular extensions•Push / pull torch compatible•Up / down torch enables adjustment •by operator while weldingJob mode / memory•Key lock optional•Optional multi-lock torch body •exchanging systemEarth leakage monitoring•Thermostatic fan•Water cooler option•

SPECIFICATIONS

Duty Cycle RatingTS4000

400 Amps @ 40%•365 Amps @ 60%•320 Amps @ 100%•

TS5000500 Amps @ 40%•450 Amps @ 60%•360 Amps @ 100%•

Wire SizesHard Wire

0.8mm 0.9mm 1.0mm 1.2mm 1.6mm


Cored Wire 1.2mm 1.6mm 2.0mm

Dimensions (wheels attached)625 x 290 x 475 mm TS4000 & TS5000PS Weight TS4000 35.5kgPS Weight TS5000 36kg

8S

EC

TIO

N O

NE

– M

AC

HIN

ES

FRONIUS TRANSPUlSE SYNERGIC 2700

PN: TPS2700 4.075.095.638

The Fronius TPS2700 is the answer when welding aluminium, steel, stainless and CrNi for those who build boats, trailers, tanks or in the field. The TPS2700 is light weight and can be used either manually or can be coupled to robotic systems for maximum productivity and performance.

FEATURESIntegrated 4 wheel drive wire feeder•Portable•Outstanding precision•Digital welding-process control•Superb welding properties•MIG brazing of galvanised sheets•Start-up program for aluminium•MIG pulsed-arc•Synergic programs•TIG and Electrode welding (VRD)•Serial interface for data transmission•Easy operation•Digital display for amps, volts, •material thickness, wire feed speed, inductance, arc length, etcRemote controllable•User defined function key•Continuous power adjustment is •possible directly from torches with up / down modeSimple to calibrate•Job / memory mode•Thermostatic fan•Push / pull and multi-lock compatible•

SPECIFICATION

Duty Cycle Rating270 Amps @ 40%•210 Amps @ 60%•170 Amps @ 100%•


0.8mm 0.9mm 1.0mm 1.2mm


Cored Wire 1.2mm 1.6mm

Dimensions625 x 290 x 480 mm PS Weight TPS2700 27.5kg

9S

EC

TIO

N O

NE

– MA

CH

INE

SFRONIUS TRANSPUlSE SYNERGIC 3200 / 4000 / 5000

PN: TPS3200 4.075.124

PN: TPS4000 4.075.100.638Gas or Water Cooled

PN: TPS5000 4.075.102.638Gas or Water Cooled

FRONIUS T.I.M.E. 5000

PN: TIME 5000 4.075.140.930

The T.I.M.E. 5000 is a continuously adjustable GMA machine suitable for structural steel, shipyards, offshore, apparatus construction, mechanical engineering, tank manufacturing and aluminium ship building.

FEATURESHigh deposition MAG Process •(T.I.M.E.) Carbon steels onlyDigital welding-process control•4 roller drive•Modular extensions•Serial interface for data transmission•MIG brazing of galvanised sheets•Synergic programs•TIG lift arc ignition•Digital display for welding amperage, •welding voltage, thickness of material, wire feed speedRemote-controllable•Push pull torch or push torch•Continuous power-adjustment •possible directly from torches with Up/Down modeJob mode•Key lock optional•MIG Pulsed-arc•

S mark, CE mark, C Tick, VRD•Optional Multi-lock torch body •exchanging systemEarth leakage monitoring•

SPECIFICATION

Duty Cycle Rating400 Amps @ 100% •500 Amps @ 75%•


0.8mm 0.9mm 1.0mm 1.2mm 1.6mm



Dimensions625 x 290 x 480 mm PS Weight 36kg

SPECIFICATION

Duty Cycle RatingTPS3200

320 Amps @ 40%•260 Amps @ 60%•220 Amps @ 100%•

TPS4000400 Amps @ 40%•365 Amps @ 60%•320 Amps @ 100%•

TPS5000500 Amps @ 40%•450 Amps @ 60%•340 Amps @ 100%•


0.8mm 0.9mm 1.0mm 1.2mm 1.6mm



Dimensions625 x 290 x 475 mm PS Weight TPS3200 35.6kgPS Weight TPS4000 35.5kgPS Weight TPS5000 36.0kg

The Fronius TPS3200/4000/5000 are ideally suited for welding structural steel, shipyards, offshore, apparatus construction, mechanical engineering, tank manufacturing and aluminium ship building.

FEATURESSuperb welding properties•Digital welding-process control•4 roller drive•Modular extensions•Serial interface for data transmission•MIG brazing of galvanised sheets•Synergic programs•TIG lift arc ignition•Easy operation•Digital display for welding amperage, •welding voltage, thickness of material, wire feed speedRemote-controllable•Push pull torch or push torch•Continuous power-adjustable directly •from torches with up / down modeJob mode•Key lock optional•MIG/MAG pulsed-arc•Arc air gouging (TPS 5000)•S mark, CE mark, C tick, VRD•Optional multi-lock torch body •exchanging systemEarth leakage monitoring•

10

SE

CTIO

N O

NE

– M

AC

HIN

ES Remote Controls and Extension Cables

Part-number Description4.046.082 TR1000 jobmaster remote control, incl. 5m cable4.046.079 TR2000 program remote control, incl. 5m cable4.046.080 TR4000 universal remote control, incl. 5m cable4.046.081 TR4000 C comfort remote control, incl. 5m cable4.100.265 Remote control magnet mounting kit43.0004.0633 Extension cable 10-pin 5m43.0004.1017 Extension cable 10-pin 10m

MIG REMOTE CONTROl SElECTION TABlE

FRONIUS AUTOMATION

TR2000 4.046.079

TR4000C 4.046.081

RCU5000

TR1000 4.046.082

Remote Control Units

TR 1000

TR 1100

TR 2000

TR 2200 F

TR 3000

TR 4000

TR 4000 C

RCU 5000

TransSynergic 4000 • • • • • • • •TransSynergic 5000 • • • • • • • •TransPulsSynergic 2700 • • • • • • • •TransPulsSynergic 4000 • • • • • • • •TransPulsSynergic 5000 • • • • • • • •Welding current X X X X X X X XMMA arc force X X X X XHotstart X X XWelding power X X X XWire feed speed X X X X XWelding voltage X X X XArc length X X X X X XGlobule shedding X X XMIG arc force X X XPulsing/standard mode X XPulsing/standard/manual mode X XProgram selection X X X XMagnetic holder Option X Option OptionV/A/m/min/mm - displays X X X X X XFunction buttons X XProgram-point programming X X

•Suitable XInstalled

TR4000 4.046.080

The Fronius inverter technology offers optimum performance and consistency which lends itself to coupling this equipment to robotic equipment. For any welding application. Custom design to suit your needs.

11

SE

CTIO

N O

NE

– MA

CH

INE

SFRONIUS TIG 1700

PN: TT1700 4.075.115

The TIG 1700, with its inverter technology, offers a portable, lightweight unit but a heavy weight when it comes to power and is suitable on construction sites for the site-erection work or repair jobs. It is often used in the pipeline / oil & gas industry and for installation and maintenance work.

FEATURESTIG-DC & electrode welding•240 volt single phase•Hi Frequency TIG ignition•Up/down function via torch•Generator compatible•Security Code•Thermostat controlled fan•2-step operation / 4-step operation•S-mark, CE-mark, C Tick•Digital Display•

SPECIFICATION

Duty Cycle Rating170 Amps @ 40% 40ºC•120 Amps @ 100% 40ºC•150 Amps @ 100% 25ºC•

Dimensions430 x 180 x 280 mm Weight 8.9kg

12

SE

CTIO

N O

NE

– M

AC

HIN

ES

FRONIUS TT 2500 / 3000 / 3000 MV

PN: TT 2500 4.075.152.631

PN: TT 3000 4.075.154.631

PN: TT 3000 MULTI VOLTAGE 4.075.154.800

Recommended for use in construction of chemical plant, tanks, containers, mechanical, pipeline construction, automative, railway engineering, site erection, maintenance and repair firms.

FEATURESDC TIG & electrode welding•415 Volt 3 phase•Programmable gas pre-flow, starting •current, upslopeAdjustable down-slope, end-crater •current, continuously adjustable welding currentDigital end crater current indicator•Welding-current-dependent gas post-•flow2-step / 4-step operation•Hi Frequency TIG ignition•Digital volt and ammeter with •command value and storable actual value (hold function)Indicator for over-temperature•Gas test function•Generator compatible•Error code indication to facilitate •serviceSecurity code•Computer controlled power source•

Simplified operation•Temperature controlled fan•Automatic cut-off of cooling unit•Run status indicator and activated •danger reduction indicatorUser friendly design•New transport technology•Simplified handling•Protected user interface with •systematic functionsS-mark, CE-mark, C Tick, VRD option•Up/down function via torch•

SPECIFICATION

Duty Cycle RatingTT 2500

250 Amps @ 50%•190 Amps @ 100%•

TT 3000300 Amps @ 50%•240 Amps @ 100%•

TT 3000 MV300 Amps @ 50%•240 Amps @ 100%•

DimensionsTT 2500 / TT 3000 / TT 3000 MV560 x 250 x 435 mm Weight TT 2500 24.2kgWeight TT 3000 24.2kgWeight TT 3000 MV 25.9kg

FRONIUS MAGIC WAVE ® 1700 / 2200

PN: MW 1700 4.075.121

PN: MW 2200 4.075.119

Used in the construction of plant, containers, machinery, structural steel, automobile, allied vendor and aerospace industries. Also in the repair and maintenance of marine vessels, manufacturing tubular frames such as high performance bikes and other vehicles and restoration work.

FEATURESAC/DC TIG & electrode welding•170/220 Amps from 240 Volt single •phaseAutomatic cap-shaping•Automatic cooling-unit cut out•Lift arc ignition / HF switch-selectable•Store up to 100 jobs•Generator compatible•Gas test button•Polarity reversal•Pulse mode•Robot interface optional•Up/Down function via torch•

2-step / 4-step operation•Spot-welding•Digital display•Over temperature protection•Earth leakage monitoring•Carrying strap•Thermostat-controlled fan•S-mark, CE-mark, C Tick, VRD option•

SPECIFICATION

Duty Cycle RatingMAGIC WAVE ® 1700

170 Amps @ 35%•130 Amps @ 60%•100 Amps @ 100%•

MAGIC WAVE® 2200220 Amps @ 35%•170 Amps @ 60%•150 Amps @ 100%•

DimensionsMAGIC WAVE® 1700 / 2200485 x 180 x 344 mmWeight 1700 14kg Weight 2200 16.5kg

13

SE

CTIO

N O

NE

– MA

CH

INE

SFRONIUS MAGIC WAVE® MW 2500 / 3000 / 3000 MV

PN: MW 2500 4.075.155

PN: MW 3000 4.075.157

PN: MW 3000 MV 4.075.157.800

Recommended for use in construction of chemical plant, tanks, containers, mechanical, pipeline construction, automative, railway engineering, site erection, maintenance and repair firms.

FEATURESTIG-AC/DC & electrode welding•415 volt 3 phase•Programmable gas pre-flow•Programmable starting current•Programmable upslope•Continuously adjustable welding •currentAdjustable down-slope•Adjustable end-crater current•Digital end-crater current indicator•Welding-current-dependant gas post-•flowProgrammable AC frequency•Adjustable AC balance cleaning•Continuously adjustable AC waveform•2-step / 4-step operation•Non-contact TIG ignition•Security code•Digital volt and ammeter with •command value and storable actual value (hold function)

Over temperature indicator•Error code indication to facilitate •serviceRun status indicator•Indication of activated hazard •minimization deviceGas test button•Thermostat controlled fan•Generator compatible•Automatic cooling unit cut off•S-mark, CE-mark, C Tick, VRD option•Up/Down function via torch•

SPECIFICATION

Duty Cycle RatingsMW 2500

250 Amps @ 40%•170 Amps @ 100%•

MW 3000 / 3000 MV300 Amps @ 35%•190 Amps @ 100%•

DimensionsMW 2500 / 3000 / 3000 MV560 x 250 x 435 mmWeight 26.6kg / 28.1kg / 30kg

FRONIUS MAGIC WAVE® 4000 / 5000

PN: MW4000 4.075.132

PN: MW5000 4.075.134

Recommended for use in the automobile and allied vendor industries, construction of plant, containers, machinery, structural steel, rail vehicles, rolling stock, shipbuilding and offshore engineering.

FEATURESTIG AC/DC & electrode welding•400/500 Amps digital power source•Automatic cap-shaping•TAC – special tack mode•Lift arc ignition / HF switch-selectable•Store up to 100 jobs•Generator compatible•Gas test button•Polarity reversal•Pulse mode•Robot interface optional•Up/Down function via torch•2-step / 4-step operation•Spot-welding•Digital display•Over temperature protection•Earth leakage monitoring•Carrying strap•Thermostat-controlled fan•S-mark, CE-mark, C Tick•VRD option•

SPECIFICATION

Duty Cycle RatingMAGIC WAVE ® 4000

400 Amps @ 45% •365 Amps @ 60% •310 Amps @ 100% •

MAGIC WAVE ® 5000500 Amps @ 45%•450 Amps @ 60% •350 Amps @ 100%•

DimensionsMAGIC WAVE® 4000 / 5000625 x 290 x 705 mmWeight 58.2kg / 58.2kg

14

SE

CTIO

N O

NE

– M

AC

HIN

ES

FRONIUS Kd 4010 WIRE FEEdER TO SUIT AUTOMATIC / MANUAl TIG WEldING

FRONIUS Kd 4000-d11 TIG COld WIRE FEEdER

PN: KD4010 8.045.059Stand alone cold wire feeder.

FEATURESTIG cold wire feeder•240 Volt single-phase•Continuous or pulse wire feed•Internal or external control•Automatic wire retract•Wire feed start from TIG torch•4 roller drive system•

Synchronised wire pulsing when used •with Fronius welding power sourceS-mark, CE-mark, C Tick•

SPECIFICATION

Wire Feed Speed30-999cm/minDimensions625l x 250w x 300hWeight 17.5kg

PN: KD4000-D11 4.045.959

Cold wire feeder controlled by Fronius digital machines.

FEATURES

SPECIFICATION

Wire Feed Speed0.1–11.0m/min

Dimensions650 x 290 x 410mmWeight 16.0kg

FRONIUS MICRO PlASMA TT800

PN: MICRO PLASMA TT8004.075.120

Portable lightweight unit for micro plasma welding and soft plasma welding.

POWER SUPPLY FEATURESTungsten cannot contact work piece•Weld carbon steel•Plasma brazing plated steels•Weld stainless steel•Accurate control of Amps (0.1 Amp •steps)Touchless ignition of pilot arc•Ideal for plasma welding thin parts•Digital display of plasma gas flow•

TECHNICAL DATA

Mains Voltage 1Ø 230V+15%/-20% Mains fuse slow 16AWelding current range 0.5-80A(0.1A steps)Duty cycle 10min/40°C 60% d.c. 80AOpen circuit voltage 85VProtection class C-tick / IP23Dimensions485 / 180 / 390mmWeight 14.2kg

15

SE

CTIO

N O

NE

– MA

CH

INE

SFRONIUS ® MAGIC ClEANER

PN: STAND ALONE 4.075.092

The Magic Cleaner is used to clean and polish TIG welds on Stainless Steel. This stand alone version can be plugged into the 230v mains.

FEATURESContinuously adjustable cleaning current•Adjustable electrolyte flow•Adjustable current settings AC/DC-/DC+•Operating mode indicator •Fault indicator•Short circuit recognition and cut off•S-mark, CE-mark, C Tick•

SPECIFICATIONRelated Power: 300 W•Cleaning Current Range: 5-20 Amps•Cleaning Agent Volume: 1.5litre•

Dimensions430 x 180 x 280Weight 5kg

ACCESSORIES

PN: DESCRIPTION4.045.884 Magic Cleaner fume exhaust unit4.045.818 Hose pack Magic Cleaner 4m43.0004.0533 Earth cable 16mm2 3m44.0001.1176 MC electrode 54° complete with clamp44.0450.1019 MC electrode 54°44.0450.1040 MC electrode 30°44.0001.1313 MC electrode graphite 60° with clamp42.0411.8040 MC electrode graphite 60°42.0411.8014 Cleaning cloth for triangle (10 per pack)42.0411.8015 Magic Cleaner fluid 1 litre42.0411.8016 Magic Cleaner fluid 5 litre42.0411.8041 Magic Cleaner powder (makes 1 litre)4.100.212 Print set – 1 Magic Cleaner (Includes Magic Cleaner printing fluid 0.5 litre, printing felt, printing foil Disposable, plastic box, spare parts box)

16

SE

CTIO

N O

NE

– M

AC

HIN

ES PN: TRANSCUT 300 4.065.023

Plasma cutter with liquid operating agent. Recommended for use on mild steel, CrNi steel and aluminium materials.

POWER SUPPLY FEATURESOutput current range 16-30Amp•Input voltages 230V, 1-PH, 50Hz, •No compressed air needed•Cuts: Stainless steel, mild steel, •AluminiumExtremely low fume emissions•Fluid level sensor •Stepless amperage adjustment 16-•30AmpsOver-temperature indicator •Thermostat-controlled fan•Generator compatible•Low weight•S-mark, CE-mark and C Tick•

T30V Torch & Consumable FeaturesSuitable to Push/Drag on work piece•Safety trigger•High frequency arc initiation•Shielded front-end consumables•

Cutting capacity:Mild steel 10mmStainless steel 6mmAluminium 6mmDuty Cycle Rating:30 Amps @ 35% 40ºC16 Amps @ 100% 40ºCDimensions:460 x 180 x 275mmWeight 16kgPN:40.0009.0092 Transcut Fluid 710ml

FRONIUS TRANSCUT 300

PN: 42.0411.0038 Circle Cutting Set

PN: 42.0001.3637 Nozzle (CuCrZr)

PN: 42.0001.3638 Cathode

PN: 44.0350.2558 Protection Cap

PN: 42.0201.2167 Distance Piece

PN: 42.0435.0021 Cathode Removal Tool

PN: 40.0006.1042 Spares Kit

PN: 40.0009.0046 Fonius Coolant 5ltrTo suit water-cooled Fronius welders•

17

SE

CTIO

N O

NE

– MA

CH

INE

S

FRONIUS TRANSPOCKET 1500 / 1500 VRd

PN: TP1500 4.075.108

PN: TP1500 VRD 4.075.108.638

Recommended for use in construction of chemical plants, maintenance & repair, construction of plant, containers, machinery and structural steel.

Industry plant & pipeline construction and site erection firms.

FEATURES240v single phase•Weighs only 4.7kg•Sturdy, impact proof housing•Generator compatible•Able to weld Cellulose electrodes•Thermostat controlled fan•Removable steel mesh dust filter•Ideal for typical welding job: Rod •–electrode and TIG welding with lift arc ignitionSuitable for construction sites and •workshopsRemote controllable version (RC •version)S-mark, CE-mark and C Tick•Controls located in protective recess•

SPECIFICATION

Duty Cycle Ratings140 Amps @ 35% •80 Amps @ 100% •

Dimensions315 x 110 x 200 mmWeight 4.7kgOPTIONAL – “VRD”

PN: TP125 4.075.108.631/125

PN: TP125 VRD 4.075.108.639/125



FEATURES240v single phase•Weighs only 4.7kg•Sturdy, impact proof housing•Generator compatible•Able to weld Cellulose electrodes•Thermostat controlled fan•Removable steel mesh dust filter•Ideal for typical welding job: Rod •

FRONIUS TRANSPOCKET 125 / 125 VRd

–electrode and TIG welding with lift arc ignitionSuitable for construction sites and •workshopsRemote controllable version (RC •version)S-mark, CE-mark and C Tick•Controls located in protective recess•

SPECIFICATION

Duty Cycle Ratings140 Amps @ 35% •125 Amps @ 70% •

Dimensions315 x 110 x 200 mmWeight 4.7kg

18

SE

CTIO

N O

NE

– M

AC

HIN

ES

FRONIUS TRANSPOCKET 1500 TIG / 1500 VRd TIG

PN: 1500 TIG 4.075.110.630

PN: 1500 VRD TIG 4.075.110.638



FEATURES240v single phase•Gas valve in power source (1500 TIG)•5 Pulse TIG settings (1500 TIG)•Amp control on TIG torch (1500 TIG)•Able to weld Cellulose electrodes•Thermostat controlled fan•Removable steel mesh dust filter•Ideal for the typical welding job: Rod-•electrode and TIG welding with lift arc ignitionSuitable for construction sites and •workshopsGenerator compatible•S-mark, CE-mark and C Tick•Operates on 110 & 240 volts (1500MV)•

SPECIFICATION

Duty Cycle Rating140 Amps @ 35% •80 Amps @ 100% •

Dimensions315 x 110 x 200 mmWeight 4.8kgOPTIONAL – “VRD”

19

SE

CTIO

N O

NE

– MA

CH

INE

S

TRANSPOCKET 4000 CEl / 5000 CEl

PN: 4000 CEL 4.075.111

PN: 5000 CEL 4.075.113



FEATURES415v 3 phase•Microprocessor controlled•Generator compatible•S-mark, CE-mark and C Tick, VRD•Continuously adjustable welding •currentElectronic regulation ensures constant •current regardless of mains voltage fluctuations and length of welding cablesPrecise MMA arc-striking behaviour •thanks to HOT-STARTSuitable for vertical-down welds with •CEL electrodesTIG welding with lift arc-striking •Mains voltage and temperature •monitoring

Thermostat-controlled fan•Simple operation thanks to clear-cut •designLow no-load power•Continuously adjustable welding •parameter settings ensure stable arc with little or no spatterWireless remote control unit available•

SPECIFICATION

Duty Cycle RatingTRANSPOCKET 4000 CEL

380 Amps @ 40% •360 Amps @ 60% •320 Amps @ 100% •

TRANSPOCKET 5000 CEL480 Amps @ 40%•420 Amps @ 60%•360 Amps @ 100%•

Dimensions625 x 290 x 475mmWeight 4000CEL 36.1kg Weight 5000CEL 37kg

FRONIUS TRANSPOCKET 2500 / 3500

PN: TP2500 4.075.141

PN: TP3500 4.075.143



FEATURES415v 3 phase•Cellulose electrode mode•Stepless amperage adjustment 10-•250/10-350 AmpsHigh duty cycle•Digital control by DSP•Continuously adjustable Hot-start•Remote control receptacle •Arc Force control•Anti-stick device•TIG lift arc ignition•Over-temperature indicator •Thermostat-controlled fan•Generator compatible•High efficiency•S-mark, CE-mark and C Tick, VRD•

SPECIFICATION

TP2500 Duty Cycle Rating250 Amps @ 35% 40ºC•200 Amps @ 60% 40ºC•

TP3500 Duty Cycle Rating350 Amps @ 35% 40ºC•280 Amps @ 60% 40ºC•

TP2500 Dimensions430 x 180 x 320mmTP3500 Dimensions490 x 190 x 390 mmWeight TP2500 12.5kgWeight TP3500 18.0kg

20

SE

CTIO

N O

NE

– M

AC

HIN

ES FRONIUS REMOTE CONTROL UNITS for MMA Inverter Power Sources

Part-number Description4.046.076 TP MC Cel MMA remote control4.046.048 TP MC manual electrode remote control unit4.046.001 TP 4 hand held remote control4.046.057 TR 55 MC robot remote control unit4.046.050 TR 52 MC pedal remotre control4.046.051 TR 53 MC manual AC-remote control unit4.046.052 TR 51 MC spot welding remote control unit4.045.132 TR 51 spot welding remote control unit4.046.049 TR 50 MC pulsing remote control43.0004.0459 Remote control cable 10-pin 5m43.0004.0460 Remote control cable 10-pin 10m43.0004.0509 Remote control cable 10-pin 20m43.0004.0548 Remote control cable 10-pin 30m4.046.082 TR 1000 jobmaster remote with cable 5m4.046.085 TR 1100 remote control with cable 4.5m4.046.079 TR 2000 remote control with cable 5m4.046.083 TR 3000 electrode remote control with cable 5m4.046.080 TR 4000 universal operation with cable 5m4.046.089 RCU 2000 TIG remote control with cable 5m4.046.090 TR 2200-F pedal remote control with cable 5m4.100.265 Built-in-kit magnet for remote control43.0004.0633 Extension cable 10-pin 5m43.0004.1017 Extension cable 10-pin 10m

MMA REMOTE CONTROl SElECTION TABlE

REMOTE CONTROL UNITS for MMA Inverter Power sources

TP 08

TR 1000

TR 1100

TR 1500

TR 1500-F

TR 2000

TR 3000

TR 4000

TR 4000C

TransPocket 1500 RC • •TransPocket 1500 TIG • •TransPocket 2000 • • • • • •TransPocket 4000 CEL • • • • • • •TrancPocket 5000 CEL • • • • • • •Welding current X X X X X X X X XMMA arc force X X X XHotstart X XPolarity reversal XWelding current regulated XMagnetic holder Option X Option OptionDisplay amperage – comm. Value

X X X X

Voltage display X XHold display X XFunction selection switch X

MMA REMOTE CONTROl FEATURE TABlE

TP MC Cel 4.046.076

TR 1000 4.046.082

TR 52 MC 4.046.050

RCU 2000 4.046.089

TR 2000 4.046.079

TR 4000 4.046.080

TR 2200-F 4.046.090

TR 50 MC4.046.049

TR 1000 4.046.082

TR 2000 4.046.079

TR 4000 4.046.080 TR4000C

4.046.081

21

SE

CTIO

N O

NE

– MA

CH

INE

S

Rem

ote

Co

ntr

ol U

nit

s fo

r T

IG I

nve

rter

Po

wer

So

urc

es

TR

1000

TR

1100

TR

2000

TR

3000

TR

4000

TR

2200

FR

CU

20

00TP

MC

C

EL

TP

MC

TP

4TR

55

MC

TR

53M

CTR

53

TR

52 M

CTR

52

-1TR

51

MC

TR

50 M

CTR

50

-1M

agic

Wav

e 17

00/2

200

••

••

••

•M

agic

Wav

e 26

00•

••

••

•M

agic

Wav

e 26

00 C

EL

•

••

••

••

Mag

icW

ave

450

••

•Tr

ansT

ig 1

600/

1700

/300

0•

••

••

Tran

sTig

220

0•

••

••

••

Tran

sTig

260

0 C

EL

••

••

••

Tran

sTig

450

••

•W

eldi

ng c

urre

ntX

XX

XX

XX

XX

XX

XX

XX

XX

XM

MA

arc

forc

eE

EE

EX

XX

Hot

star

tE

EX

XX

Pola

rity

reve

rsal

EX

XB

ackg

roun

d cu

rren

t(%)

XX

XX

Pul

s du

ty-c

ycle

XX

XX

Pul

sing

freq

uenc

yX

XX

XP

ulsi

ng fr

eque

ncy

rang

eX

XX

XS

pot w

eldi

ng ti

me

XX

Ac-

bala

nce

WX

XX

XA

C-fr

eque

ncy

WW

XX

Mag

netic

hol

der

Opt

ion

XO

ptio

nX

XX

XX

XD

ispl

ayX

XX

XX

I2W

WP

rogr

am s

elec

tion

XX

XP

rogr

am-p

oint

pro

gr.

XS

witc

h of

TIG

/ E

mod

eX

XE

= M

ode:

Ele

ctric

W =

Mod

e: T

IG

X

= M

ode:

TIG

/Ele

ctro

de

TIG REMOTE CONTROl FEATURE TABlE

TR20

00

4.04

6.02

9TR

1000

4.

046.

082

TR40

00

4.04

6.08

0TR

2200

F 4.

046.

090

TP M

C C

el

4.04

6.07

6TR

52

MC

4.

046.

050

RC

U 2

000

4.04

6.08

9TR

50

MC

4.04

6.04

9TR

53

MC

4.04

6.05

1

22

SE

CTIO

N O

NE

– M

AC

HIN

ES

For both robotic and manual applications CMT makes it possible to weld with lower thermal input and high process stability. This opens new joint designs such as welding 0.3mm sheet and joining steel to aluminium with zero spatter and flawless weld appearence. The CMT technology not only gives a welding and brazing solution with less thermal input, it also boasts one truly compelling advantage: a stable arc that refuses to “lose its cool”

Deltaspot: A resistance welding revolution, every single weld spot is 100% replicated - identically without spatter. Deltaspot technology produces unprecedentedly high-quality joins on sheets of different materials and thickness. Steel, galvanised steel, aluminium and stainless steel all joined with “spot-on” accuracy, time after time, spot for spot.

TransCut is the lightest plasma-cutting device in its class. Its secret is that it uses fluid as a cutting medium instead of compressed air. Portability is the key. Clean as well, producing up to 90% less pollutant emissions helping you to breathe easy. Ask for a demonstration to see for yourself.

Training programs, both formal and informal can be designed to suit each customer’s requirements. This ensures you extract the full benefits from your investment MIG MAG, TIG, Plasma, CMT, MIG Brazing, MMAW and others.

23

SE

CTIO

N O

NE

– MA

CH

INE

SCEBORA BRAVO MIG 155

PN: 494

The Bravo 155 is renowned for its reliability. The simple yet effective design, make this machine ideal for automotive repair, maintenance and small workshops.

FEATURES28-155 Amps welding range•Binzel style MIG torch•Reverse polarity for gas or gasless •wire1kg or 5kg Spools can be used•Fan cooled•Thermal overload protection•7 Voltage settings•Direct connect torch•Welds up to 6mm plate•0.6mm-0.9mm Wires•Portable•Copper wound transformer•2 Year warranty•Wheel kit fitted•Gas bottle strap•15 Amp 1Ø plug fitted•

SPECIFICATION

Duty Cycle Rating120 Amps @ 20%70 Amps @ 60%55 Amps @ 100%Wire Sizes Roller TypeHard Wire

0.6mm V 0.8mm V 0.9mm V

Cored Wire 0.9mm Knurled


CEBORA STAG 196

PN: 534

The Stag 196 is a reliable compact machine designed for use in auto repair shops and for hobbyists. It is suited to welding light gauge steels where it has outstanding low current welding ability.

FEATURES15-195 Amp welding range•Euro torch connection•5kg or 15kg spools can be used•Fan cooled•Thermal overload protection•7 voltage settings•Welds up to 7mm plate•0.6mm-0.9mm Wires•Copper wound transformer•Sturdy construction•Suitable for 3 or 4 metre torch•Gas bottle strap•Wheel kit fitted•2 Year warranty•15 Amp 1Ø plug fitted•

SPECIFICATION

Duty Cycle Rating130 amps @ 20%Wire Sizes Roller TypeHard Wire

0.6mm V 0.8mm V 0.9mm V

Soft Wire 0.9mm U 1.0mm U 1.2mm U

Cored Wire 0.9mm Knurled


24

SE

CTIO

N O

NE

– M

AC

HIN

ES

CEBORA PUlSE 2035/M

PN: 285

Portable yet powerful 240V pulse MIG welder. This machine uses the latest technology and is a market leader in portable pulse MIG welding. It is designed to weld the latest high strength steels and alloys used in the automotive repair industry, including MIG brazing.

FEATURESInverter technology•15-205 Amp welding range•Euro torch connection•5kg Spool internal•15kg Spool using spool kit•Fan cooled•Thermal overload protection•Pre and post gas control•Step less voltage adjustment•Welds up to 10mm steel•Welds up to 7mm aluminium•Welds up to 7mm stainless steel•Pulse, synergic & standard MIG •modesUpgradeable software•Quality geared drive roll system•Soft start features•Crater fill•Upslope•Digital meters•Push/pull compatible•Remote control compatible•2 Year warranty•

SPECIFICATION


0.6mm V 0.8mm V 0.9mm V


Cored Wire 0.9mm Knurled 1.2mm Knurled

Dimensions (no spool adaptor)458 x 260x 471Weight 20kg

CEBORA COMBI 2020/M

PN: 574

The Cebora Combi 2020/M is a portable and powerful 200 amp compact MIG designed for industrial use. This machine has a quality two roll drive system and is ready to work.

FEATURES25-200 Amp welding range•Euro torch connection•5kg or 15kg Spools can be used•Fan cooled•Thermal overload protection•7 Voltage settings•Welds up to 8mm plate•0.6mm-1.0mm wires•Copper wound transformer•Sturdy construction•Suitable for 3 or 4 metre torches•Gas bottle strap•Wheel kit fitted•15 Amp 1Ø plug fitted•12 Mths warranty•

SPECIFICATION


0.6mm V 0.8mm V 0.9mm V




25

SE

CTIO

N O

NE

– MA

CH

INE

SCEBORA dOUBlE PUlSE 2035/Md

PN: 286

Portable yet powerful 240V pulse MIG welder. This machine uses the latest technology and is a market leader in portable pulse MIG welding. It is designed to weld the latest high strength steels and alloys used in the automotive repair industry, including MIG brazing.

FEATURESDouble pulse programs•Inverter technology•15-205 Amp welding range•Euro torch connection•5kg Spool internal•15kg Spool using spool kit•Fan cooled•Thermal overload protection•Pre and post gas control•Stepless voltage adjustment•Welds up to 10mm steel•Welds up to 7mm aluminium•Welds up to 7mm stainless steel•Pulse, synergic & standard MIG •modesUpgradeable software•Quality geared drive roll system•Soft start features•Crater fill•Upslope•Digital meters•Push/pull compatible•Remote control compatible•2 Year warranty•

SPECIFICATION


0.6mm V 0.8mm V 0.9mm V



Dimensions (no spool adaptor)458 x 260x 471Weight 20kg

CEBORA 2540/T

PN: 591

The Cebora 2540/T is a 3 phase compact MIG welder, designed for industrial workshops, site-work (where 3-phase is available) and also in trade schools.

FEATURES15-250 Amps welding range•12 Voltage settings•Euro torch connection•Weld spot timer control•Uses 5 or 15kg spools•Fan cooled•Thermal overload protection•0.6mm-1.2mm wires•Sturdy construction•Suitable for 3mtr or 4mtr torches•Gas bottle carrier•Wheel kit fitted•Compact design•2 year warranty•Push/pull torch compatible•

SPECIFICATION


0.6mm V 0.8mm V 0.9mm V 1.0mm V 1.2mm V


Cored Wire 0.9mm Knurled 1.0mm Knurled 1.2mm Knurled


26

SE

CTIO

N O

NE

– M

AC

HIN

ES

CEBORA SYNERGIC 3840/T & 3840/TS

PN: 581

The Cebora 3840/T is a 380 Amp synergic MIG welder. This unit is ideally suited to automotive repair, small fabrication workshops using mild steel, stainless steel or aluminium.

FEATURESBuilt-in synergic programs•Post gas timer•Soft-start adjustments•38-380 Amps welding range•Uses 5-15kg spools•Gas or gasless wire compatible•Euro torch connection•16 voltage settings•10 Mtr interconnecting leads on SWF •modelsThermal overload protection•Fan cooled•Suitable for 3 or 4 metre torches•Gas bottle carrier•Wheel kit fitted•2 Year warranty•Push/pull torch compatible•4 Roll drive on SWF models•Enclosed spool holder•

SPECIFICATION





DimensionsCompact 915 x 542 x 795SWF Model 975 x 615 x 900 PS onlyWeight Compact 90kg PS onlyWeight SWF Model 85kg PS only

CEBORA SYNERGIC 2235/T

PN: 573

The Cebora 2235/T is a compact, 3-phase, 250 Amp MIG welder with built-in synergic control, that simply takes all the guess work out of welding. By selecting the appropriate wire/gas combination you can start welding. “It’s that easy”.

FEATURESBuilt-in synergic programs•Post-gas timer•Soft-start adjustments•15-220 Amps welding range•Uses 5-15kg spools•Gas or gasless wire compatible•Euro torch connections•7 Voltage settings•Super compact•Thermal overload protection•Fan cooled •Suitable for 3mtr or 4mtr torches•Gas bottle carrier•Wheel kit fitted•2 Year warranty•Push/pull torch compatible•

SPECIFICATION


0.6mm V 0.8mm V 1.0mm V 1.2mm V




27

SE

CTIO

N O

NE

– MA

CH

INE

SCEBORA SYNERGIC 4540/T & 4540/TS

PN: 597 4540/T

PN: 615 4540/TS

The Cebora 4540/T & 4540/TS are 3 phase synergic MIG welders, that have all the features including synergic control. With 450 Amps of power, this enables some of the most difficult tasks to be accomplished, using mild steel, stainless steel & aluminium.

FEATURES40-450 Amps welding range•32 Voltage settings•10 Mtr interconnecting leads on SWF •model4 Roll drive system on SWF models•Built-in synergic programs•Uses 5–15kg spools•Gas or gasless wire compatible•Thermal overload protection•Fan cooled•Soft start adjustments•Euro torch connection•Gas bottle carrier•Wheel kit fitted•Water cooler unit compatible•Water cooled torch compatible•2 Year warranty•Enclosed spool holder•

SPECIFICATION

Duty Cycle Rating400 Amps @ 40%330 Amps @ 60%260 Amps @ 100%Wire Size Roller TypeHard Wire


Soft Wire 0.9mm U 1.0mm U 1.2mm U 1.6mm U


DimensionsCompact 915 x 542 x 795SWF Model 975 x 615 x 900 PS onlyWeight Compact 94kgWeight SWF Model 118kg

CEBORA SYNERGIC 4750/TS

PN: 617

The Cebora 4750/TS is a 470 Amp 3 phase MIG unit built for tackling those more demanding tasks. The 4750/TS has a 4 roll drive system which enhances its performance on various base materials including mild steel, stainless steel and aluminium.

FEATURES40-470 Amps welding range•32 Voltage settings•10 Mtr interconnecting leads•4 Roll drive system•Built-in synergic programs•Uses 5–15kg spools •Thermal overload protection•Fan cooled•Soft start adjustment•Euro torch connection•Gas bottle carrier•Enclosed spool holder•Wheel kit fitted•Water cooler unit compatible •Water cooled torch compatible•2 Year warranty•

SPECIFICATION

Duty Cycle Ratings420 Amps @ 50%390 Amps @ 60%300 Amps @ 100%Wire Size Roller TypeHard Wire



Cored Wire 0.9mm Knurled 1.0mm Knurled 1.2mm Knurled 1.6mm Knurled

Dimensions975 x 640 x 900 PS onlyWeight 138kg

28

SE

CTIO

N O

NE

– M

AC

HIN

ES

CEBORA SOUNd MIG 3840/T PUlSE

PN: 287

The Cebora 3840/T pulse MIG welding unit is a 3 Phase power source coupled to a 4 roll drive wire feeder and a water cooler unit. Enabling perfect results, from ultra-thin aluminium to heavy steel or stainless, this unit will out perform most others with ease.

FEATURES5-380 Amps welding range•Stepless electronic voltage control•10 Metre interconnecting cables•4 Roll drive system•Built-in synergic programs•Thermal overload protection•Fan cooled•Soft-start adjustment•Euro torch connection•Enclosed spool holder•Water cooler unit fitted•Water cooled torch fitted•Wheel kit fitted•2 Year warranty•Gas bottle carrier•Push/pull torch compatible•Multi-process power source inc MIG, •TIG & stickDigital display•Light weight•

SPECIFICATIONS

Duty Cycle Rating380 Amps @ 40%340 Amps @ 60%310 Amps @ 100%Wire Sizes Roller Type

Hard Wire 0.6mm V 0.8mm V

0.9mm V 1.0mm V 1.2mm VSoft Wire 0.9mm U 1.0mm U 1.2mm U 1.6mm UCored Wire 0.9mm Knurled 1.0mm Knurled 1.2mm Knurled 1.6mm Knurled


CEBORA SYNERGIC 5550/TS

PN: 619

The Cebora 5550/TS is designed and built for heavy industrial applications such as mining, earthmoving and structural steel where more power is required. The 5550/TS has a factory fitted TDA4 which enables better control where high quality welds and a perfect finish is essential.

FEATURES40-550 Amps welding range•32 Voltage settings•10 Mtr interconnecting leads•4 Roll drive system•Built-in synergic programs•Uses 5–15Kg spools•Thermal overload protection•Fan cooled•Soft-start adjustment•Euro torch connection•Enclosed spool holder•Wheel kit fitted•Water cooler unit compatible•Water cooled torch compatible•2 Year warranty•

SPECIFICATION

Duty Cycle Ratings500 Amps @ 50%450 Amps @ 60%350 Amps @ 100%Wire Sizes Roller TypeHard Wire

0.6mm V 0.8mm V

0.9mm V 1.0mm V 1.2mm V 1.6mm V



Dimensions975 x 640 x 900 PS onlyWeight 155kg

29

SE

CTIO

N O

NE

– MA

CH

INE

SCEBORA SOUNd MIG 5040/Td dOUBlE PUlSE

PN: 289

The Cebora 5040/TD is a 3 Phase inverter, power source with pulse & double pulse operation, for professional use wherever excellent quality welding is required, together with high productivity. It also is a multi-process power source, able to weld in MIG-MAG, TIG mode (Lift-arc) and MMA (Stick) mode.

FEATURESDouble pulse•5-500 Amp welding range•Stepless electronic voltage control•10 Metre interconnecting cables•4 Roll drive system•Built-in synergic programs•Multi-process power source inc MIG, •TIG & StickDigital control•Digital display•Push/pull compatible•Water cooler unit fitted•Water cooled MIG torch fitted•Euro torch connection•Enclosed spool holder•Thermal overload protection•Fan cooled•2 Year warranty•Wheel kit fitted•Gas bottle carrier•Light weight•

SPECIFICATION


0.6mm V 0.8mm V 0.9mm V 1.0mm V 1.2mm V 1.6mm V




CEBORA POWER ROd 1365

PN: 252

The Cebora power rod 1365 inverter is a portable yet powerful DC, MMA and TIG welder. This machine is capable of running from a 6KVA generator and uses 1.6mm-3.2mm electrodes and also lift-arc TIG welding.

FEATURES10-135 Amp welding range•MMA power source•DC lift-arc TIG•Stepless amperage control•Inverter power•Light weight•10/25 output sockets•Suitable for maintenance or •contractorsGenerator compatible (6KVA min)•Suitable for stainless steel•Electronic control•Robust design•

SPECIFICATION

Duty Cycle Rating130 Amps @ 35%115 Amps @ 60%105 Amps @ 100%Electrode Sizes1.6mm – 3.2mmDimensions310 x 185 x 230Weight 7.3kg

30

SE

CTIO

N O

NE

– M

AC

HIN

ES

CEBORA POWER TIG 1540 dC HF

PN: 271

The Cebora 1540 power TIG is a stick and TIG welding inverter type DC power source with high frequency ignition. This machine is ideally suited to contractors and sheet metal workshops. This machine can be optioned up to have a foot control or up/down amperage adjustment on the TIG torch.

FEATURES5-150 Amp welding•DC anti-stick MMAW•DC high frequency GTAW•Stepless amperage control•Inverter power source•Light weight•35-50 Output sockets•Suitable for contractors and sheet •metal workshopsGenerator compatible (7KVA min)•Electronic control•Thermal overload protection•Robust design•Remote control recepticles•Built-in gas solenoid•Up slope control•Down slope control•Crater fill feature•Genuine Cebora trolley option•

SPECIFICATION

Duty Cycle RatingGTAW 150Amps @ 40% 130 Amps @ 60% 120 Amps @ 100%MMAW 140 Amps @ 30% 115 Amps @ 60% 105 Amps @ 100%Electrode Sizes1.6mm – 4.0mmTungsten Sizes1.0mm – 3.2mmDimensions390 x 172 x 340Weight 9.5kg

CEBORA POWER ROd 1565

PN: 253

The Cebora 1565 is the big brother to the 1365, where it has all the same features of the 1365 yet with more output. These machines are engineered according to the most advanced electronic principles, and capable of achieving the best arc characteristics in both stick and TIG welding.

FEATURESDC anti-stick MMAW•DC lift-arc GTAW•5-150 Amp welding range•Stepless amperage control•Inverter power source•Light weight•10/25 output sockets•Suitable for workshops, contractors •and site workGenerator compatible (6KVA min)•Electronic control•Thermal overload protection•Robust design•

SPECIFICATION

Duty Cycle Ratings150 Amps @ 35%125 Amps @ 60%115 Amps @ 100%Electrodes1.6mm – 4.0mmDimensions370 x 172 x 340Weight 7.9kg

31

SE

CTIO

N O

NE

– MA

CH

INE

SCEBORA POWER TIG 1665 dC HF

PN: 272

The Cebora power TIG 1665 is a stick & TIG welding inverter type DC power source with high frequency and pulse control as standard features. This machine is for professional trades people who demand very high results in 240V inverter welding.

FEATURES5-160 Amp welding range•DC anti-stick MMAW•DC High frequency, pulse GTAW•Stepless amperage control•Inverter power source•Light weight•35/50 Output sockets•Generator compatible (7KVA min)•Electronic control•Thermal overload protection•Robust design•Remote control receptacles•Built-in gas solenoid•Up/down amperage control option•Foot control option•Up slope control•Down slope control•Crater fill feature•Genuine Cebora trolley option•

SPECIFICATION

Duty Cycle RatingGTAW 160 Amps @ 40% 145 Amps @ 60% 130 Amps @ 100%MMAW 140 Amps @ 35% 125 Amps @ 60% 115 Amps @ 100%Electrode Sizes1.6mm – 4.0mmTungsten Sizes1.0mm – 4.0mmDimensions370 x 176 x 402Weight 10.5kg

CEBORA POWER TIG 1965 dC HF

PN: 277

The Cebora power TIG 1965 DC inverter power source has high frequency ignition coupled to a pulse controller. The ideal machine for stainless steel fabrication in the food industry or light manufacturing applications where weld presentation and minimal clean-up is critical.

FEATURES5-190 Amp welding range•DC anti-stick MMAW•DC HF pulse GTAW•Stepless amperage control•Inverter power source•Up slope control•Down slope control•Crater fill feature•Remote control receptacles•Built-in gas solenoid•Robust design•Up/down amperage control option•Foot control option•Electronic control•Thermal overload protection•35/50 Output sockets•Generator compatible (7KVA min)•Genuine Cebora trolley option•

SPECIFICATION

Duty Cycle RatingGTAW 190 Amps @ 35% 160 Amps @ 60% 140 Amps @ 100%MMAW 140 Amps @ 35% 125 Amps @ 60% 115 amps @ 100%Electrode Sizes1.6mm – 4.0mmTungsten Sizes1.0mm – 4.0mmDimensions370 x 176 x 402Weight 11.7kg

32

SE

CTIO

N O

NE

– M

AC

HIN

ES

CEBORA TIG SOUNd AC/dC 2643/T

PN: 351

The Cebora TIG Sound AC/DC 2643/T is a 3 phase inverter power source designed for medium to large production applications. It is an innovative type of power source that allows you to operate in synergic mode; upon selecting the material to be welded, the corresponding thickness and weld position, the power source sets and suggests the best welding condition.

FEATURESSynergic control•5-260 Amp welding range•AC or DC MMAW•AC or DC HF, pulse, synergic GTAW•Upslope control•Down-slope control•Crater fill feature•Inverter power source•Generator compatible 98KVA 415V min)•Stepless amperage control•Remote control receptacles•Built-in gas solenoid•Up/down remote amperage control•35/50 Output sockets•Water cooler option•Arc balance control•Pre & post gas control•Foot control option•Mobile unit (wheels/trolley std)•

SPECIFICATION

Duty Cycle RatingGTAW 260 Amps @ 40% 240 Amps @ 60% 230 Amps @ 100%MMAW 210 Amps @ 40% 200 Amps @ 60% 190 Amps @ 100%Electrode Sizes1.6mm – 4.0mmTungsten Sizes1.0mm – 4.0mmDimensions (wheels attached)1060 x 705 x 975Weight 65kg

CEBORA TIG SOUNd AC/dC 2030/M

PN: 346

The Cebora 2030/M TIG Sound is an AC/DC inverter power source for use in TIG and stick modes. The engineering and manufacturing technology of the machine have produced a real performer, with a welding range from 5 Amps to 200 Amps.

FEATURES5-200 Amp welding range•AC or DC anti-stick MMAW•AC or DC HF, pulse GTAW•Upslope control•Down-slope control•Stepless amperage adjustment•Inverter power source•Crater fill feature•Remote control receptacles•Built-in gas solenoid•Foot control option•Up/down amperage control option•Electronic control•Thermal overload protection•Generator compatible (7KVA min)•35-50 Output sockets•Water cooler option available•Robust design•Genuine Cebora trolley option•Arc balance control•Pre & post gas control•

SPECIFICATION

Duty Cycle RatingGTAW 200 Amps @ 30% 160 Amps @ 60% 150 Amps @ 100%MMAW 140 Amps @ 100%Electrode Sizes1.6mm – 4.0mmTungsten Sizes1.0mm – 4.0mmDimensions437 x 207 x 411Weight 16.5kg

33

SE

CTIO

N O

NE

– MA

CH

INE

SCEBORA TRI STAR MIG 1635/M

PN: 283

Multipurpose single phase power source (inverter technology) for MIG/MAG, DC TIG and MMA welding, with 2 roller wire feeder and stored synergic curves for MIG/MAG welding, electronic control of choke value, spot welding time and pause time. Comes with 3m Cebora MIG welding torch and work return lead 3m. MMA welding cables and TIG welding torch.

FEATURES5-160Amp welding range •Stepless amperage control•Inverter power source•Upslope control•Down-slope control•Robust design•Up/down amperage control option•Foot control option•Electronic control•Thermal overload protection•35/50 Outlet sockets•Generator compatible (7kVA min)•Genuine Cebora trolley option•

SPECIFICATION

Duty Cycle RatingGTAW 160 Amps @ 35% 120 Amps @ 60% 100 Amps @ 100%MMAW 130 Amps @ 45% 115 Amps @ 60% 100 Amps @ 100%GMAW 160 Amps @ 35% 120 Amps @ 60% 100 Amps @ 100%Electrode Sizes1.5mm – 3.5mmMax. wire spool size200mm Ø / 5kgDimensions207 x 437 x 411mmWeight 12.5kg

The Cebora Power Plasma 3100 was developed to respond to the need to work with a powersource that is easy to handle and to use, with minimum system requirements, but which still ensures excellent cutting quality on medium-small thicknesses. Power Plasma 3100 weighs just 13kg including the torch, and requires single-phase power supply; it works with compressed air or nitrogen (for high quality cutting), provided at a pressure of 3.7bar, with an air flow of just 60ltr/min. The recommended thickness for the best cutting quality is 6mm, but the machine may go up to 10mm with slightly inferior cutting quality; separation thickness is 12mm. Power Supply Features

Inverter Plasma•25amps output•230V Input•High frequency start•Stepless Electronic Voltage Setting•ISO & CE & C-TICK approved•IP21 C Protection•

System Specifications Max installed power 3.2KW•35% Duty cycle @ 25A•Gas Supply – Air •60ltr/min 3.5 bar Air consumption•Quality Cuts up to 6mm•Severance Cuts up to 12mm•Weighs 13kg•Dimensions 150 x 357 x 382mm•

CEBORA POWER PlASMA 3100 (ART.296)

34

SE

CTIO

N O

NE

– M

AC

HIN

ES

CEBORA PlASMA SOUNd PC 6060/T (ART.355)

CEBORA PlASMA SOUNd PC 10050/T (ART.357)

The Cebora Plasma Sound PC 6060/T is a three-phase powersource for the plasma cutting of all metals. The recommended thickness for the best cutting quality is 16mm, but the machine may go up to 22mm with slightly inferior cutting quality; separation thickness is 28mm. Its reduced size and weight make the Plasma Sound 6060/T ideal for on-site work and manual production of medium intensity (60A@60%) wherever three-phase power supply is available, but also for small automatic production applications, thanks to the improved cutting speeds and to the high continuous duty cycle (50A@100%) and a recommended cutting thickness of 16mm. Power Supply Features

Multi-Voltage Inverter Plasma•20 - 60amps output•400V Input•High frequency start•Stepless Electronic Voltage Setting•ISO & CE & C-TICK approved•IP23 C Protection•


The Cebora Plasma Sound PC 10050/T is a three-phase powersource for the plasma cutting of metals is the upward evolution of the 6060/T. The recommended thickness for the best cutting quality is 25mm, but the machine may go up to 30mm with slightly inferior cutting quality; separation thickness is 35mm. The high continuous duty cycle (85A@100%, recommended cutting thickness 20mm) and non-continuous (95A@60% recommended cutting thickness of 22mm) with increased cutting speeds to make the Plasma Sound PC 10050/T ideal for automatic production applications of average size. Power Supply Features

Multi-Voltage Inverter plasma•20 - 100amps output•400V Input•High frequency start•Stepless Electronic Voltage Setting•ISO & CE & C-TICK approved•IP23 Protection•


35

SE

CTIO

N O

NE

– MA

CH

INE

S

Cebora offers a new electromechanical plasma model to satisfy the quality cutting needs of any metal material using only compressed air. This is an ideal power source for maintenance work and medium-sized production batches. Thanks to the new Cebora CP 91 torch, it is now possible to make quality cuts of up to 12 mm on mild steel, and it can be used to separate thicknesses of up to 20 mm. The pilot arc is started using high frequency.Power Supply Features

50amps output•400V Input•High frequency start•Preset Voltage Setting•ISO & CE & C-TICK approved•IP21 C Protection•

System Specifications Max installed power 10KW•40% Duty cycle @ 50A•Gas Supply – Air•140ltr/min 4.7 bar Air consumption•Quality Cuts up to 12mm•Severance Cuts up to 20mm•Weighs 63kg•Dimensions 514 x 560 x 772mm•

CEBORA PlASMA PROF 55 (ART.965)

CEBORA PlASMA PROF 80 (ART.947)

Cebora offers this new electronically controlled plasma model, capable of satisfying the quality cutting needs of any metal material using only compressed air. This is an ideal power source for medium/high quantity production rates. The electronic control in the power source ensures maximum consistency of performance and cutting quality under all working conditions. Thanks to the new Cebora CP 91 torch, it is now possible to make quality cuts of up to 20 mm on mild steel, and it can be used to separate thicknesses of up to 30 mm. The pilot arc is started using high frequency, automatically deactivated when the arc stabilizes, thus reducing the operating time of the high voltage and frequency device. The machine is equipped with the “pilot self-restart” function - to automatically interrupt and restore the arc when cutting mesh and grids, increasing operator productivity.Power Supply Features

20 - 80amps output•400V Input•High frequency start•Stepless Electronic Voltage Setting•Detachable torch•ISO & CE & C-TICK approved•IP21 C Protection•

System Specifications Max installed power 15KW•35% Duty cycle @ 80A•Gas Supply – Air•150ltr/min 4.8 bar Air consumption•Quality Cuts up to 20mm•Severance Cuts up to 30mm•Weighs 85kg•Dimensions 514 x 560 x 772mm•

36

SE

CTIO

N O

NE

– M

AC

HIN

ES The power source PLASMA PROF 122 is a constant, direct current power source

designed for plasma cutting of all metal materials, equipped with “chopper” electronic cutting current control. The “chopper” electronic cutting current control ensures the utmost consistency of performance and cutting quality in all conditions, even when exiting the workpiece, where the difference in potential voltages between the electrode and workpiece may vary sharply. The power source PLASMA PROF 122 is equipped with high voltage and high frequency pilot arc, automatically deactivated once the pilot arc has stabilized: this reduces the working time of the high voltage and frequency device to a minimum, and thus also radiated disturbances during start-up.Power Supply Features

Chopper -Technology•20 - 120amps output•400V Input•High frequency start•Stepless Electronic Voltage Setting•Detachable torch•ISO & CE & C-TICK approved•IP21 Protection•

System Specifications Max installed power 19KW•60% Duty cycle @ 120A•Gas Supply – Air•220ltr/min 5.0 bar Air consumption•Quality Cuts up to 35mm•Weighs 120kg•Dimensions 450 x 775 x 875mm•

CEBORA PlASMA PROF 122 (ART. 946)

Cebora Plasma Prof 162 (art. 952)

The PLASMA PROF 162 is a constant, direct current power source developed using “secondary-circuit Chopper” technology, with microprocessor-controlled cutting parameters and functions. Automatic High Voltage/ Frequency pilot arc striking reduces disturbances during start-up to a minimum. The power source is capable of recognizing the type of torch connected, and automatically setting the appropriate safety devices. The area provided at the back of the machine to house the torch cooling unit allows the creation of a compact system. Using the optional interface Art.197, it is possible for the pantograph computer to remotely control:

Arc striking. - Arc transfer, with adjustable delay from 0 to 2 seconds.•Arc voltage. - Digital or isolated analog cutting current•

Power Supply FeaturesChopper -Technology•20 - 160amps output•400V Input•High frequency start•Stepless Electronic Voltage Setting•Detachable torch•ISO & CE & C-TICK approved•IP21 C Protection•

System Specifications Max installed power 22KW•35% Duty cycle @ 160A•Gas Supply – Air•220ltr/min 5.0 bar Air consumption•Quality Cuts up to 35mm•Weighs 144kg•Dimensions 450 x 775 x 875mm•

CEBORA PlASMA PROF 162 (ART. 952)

37

SE

CTIO

N O

NE

– MA

CH

INE

SUNIMIG ARC 140 & ARC 160

UNIMIG MIG / ARC 165

PN: UM140

PN: UM160DC TIG Function•Arc Leads included•Shoulder Strap included•Electrode Hot Start and Arc Force•Over Voltage and Thermal Overload Protection•High Strength Case Construction of ABS Material•

UM140 UM160Power Voltage AC240V+/-15% AC240V+/-15%Input Frequency (Hz) 50/60 50Power Rating 4.4kVA 5.2kVARated Output Current 135A MMA / 140A TIG 155A MMA/160A TIGRange of Output Current 10-140A 10-160ANo Load Voltage 56V 56VArc Ignition LIFT ARC LIFT ARCLoad Duty Cycle % 155A-30% (40°C) MMA 160A-30% (40°C) TIG 135A-30% (40°C) MMA 140A-30% (40°C) TIGProtection Class IP21S IP21SWeight (kgs) 7.6 7.6Dimensions (mm) 290 x 190 x 115 290 x 190 x 115Machine Package includes Arc 140II Arc 160II Shoulder Strap Shoulder Strap 4m Arc Leads 4m Arc Leads 12 Month Warranty 12 Month Warranty

PN: UM165DC MMA•Gas/Gasless MIG•Spool size 5kg•Euro Connect MIG Torch•

Power Voltage AC240V +/- 15%Power Rating 5kVACurrent Adjustment Range 10-140A MMA / 30-160MIGNo Load Voltage 53VLoad Duty Cycle % 140A @ 35% and 83A @ 100% MMA 160A @ 35% and 100A @ 100% MIGProtection Class IP21SWeight (kgs) 17Dimensions (mm) 480 x 230 x 360Machine Package Includes Argon Regulator SB15 MIG Torch 4m Earth Lead 4m Arc Lead MIG 165

38

SE

CTIO

N O

NE

– M

AC

HIN

ES



PN: UM190The Ultimate Welder for Site Application•DC MMA•Gas / Gasless MIG•Spool Size 5kg•Euro Connect MIG Torch•

Input Voltage (V) AC240V+/-15%Input Capacitance (kVA) 7.4No-Load Voltage 53Current Range (A) 30-175Rated Duty Cycle (%) 35% @ 175A 100% @ 103APower Factor 0.72Insulation Class IP21SProtection Class F Weight (kgs) 19Dimensions (mm) 480 x 230 x 360Machine Package includes Argon Regulator / SB15 MIG Torch 4m Earth Lead / 4m Arc Lead / MIG 190

PN: UM250The Ultimate Welder for Site Application•DC MMA•Gas / Gasless MIG•Spool Size 5kg / 15kg•Euro Connect MIG Torch•

Input Voltage (V) AC240V+/-15% 50/60HzRated MAX Input Current (A) 51 MMA 45 MIGMAGRated EFF Input Current (A) 28 MMA 26.6 MIGMAG Rated Power Capacity (kVA) 12.2 MMA 10.8 MIGMAGCurrent Adjustment Range (A) MMA 10-250Current Adjustment Range (A) MIG 30-250Voltage Adjustment Range (V) MIG 15.5-26.5No-Load Voltage (V) 56.5Welding Wire Diameter (mm) 0.6 / 0.8 / 0.9 / 1.0 Solid 0.9 / 1.0 / 1.2 / Flux Cored 0.9 / 1.0 / 1.2 AlloyRated Duty Cycle @ 40°C 35% @ 224A 100% @ 137A MMA 35% @ 250A 100% @ 148A MIGEfficiency (%) 85Power Factor 0.72Insulation Class IP21SProtection Class FInsulation Class IP21S Weight (kgs) 24Dimensions (mm) 580 x 230 x 450Machine Package includes Argon Regulator / SB24 MIG Torch 4m Earth Lead / 4m Arc Lead / MIG 250

39

SE

CTIO

N O

NE

– MA

CH

INE

SUNITIG AC/dC 200

UNITIG AC/dC 315

PN: UT200Foot Control Option•Adjustable Down Slope•2T / 4T trigger Function•Adjustable Pulse Control•HF Start AC/DC TIG Function•Adjustable Pre Gas – Post Gas•Adjustable AC Balance Control•Rugged Metal Case Construction•Tolerant to Variable Power Supply•Electrode Hot Start and Adjustable Arc Force•

Power Voltage AC240V+/-15%Input Frequency (Hz) 50Power Rating 5.8kVARated Output Current 185ARange Output Current 10-185ANo Load Voltage 56VWorking Voltage TIG 10.4 – 17.4VAC Balance / Clean Width % 20-80Slope-Down Time (Sec) 0-10Post-Flow Time (Sec) 0-10Base Current % 10-90Pulse Frequency (Hz) 0.5-300Pulse Duty Cycle% 10-90Arc Ignition HF IgnitionLoad Duty Cycle TIG 185A – 20% (40°C)Dimensions (mm) 510 x 330 x 360Weight (kg) 30Machine Package Includes SR26-4m TIG Torch / Earth Lead / Argon Regulator / Unitig AC/DC 200

PN: UT315Foot Control Option•Adjustable Down Slope•2T / 4T trigger Function•Adjustable Pulse Control•HF Start AC/DC TIG Function•Adjustable Pre Gas – Post Gas•Adjustable AC Balance Control•Rugged Metal Case Construction•Tolerant to Variable Power Supply•Electrode Hot Start and Adjustable •Arc Force

Power Voltage AC415V+/-15% 3 PhaseInput Frequency (Hz) 50 / 60Input Current MMA / 18A TIG / 12.6AEffective Current MMA / 13A TIG / 9APower Rating 12.2kVARange Output Current 10-315AArc Force (A) 0-100No Load Voltage 30VPre-Flow (Sec) 0-2Clean Width (%) 20-80Slope-Down Time (Sec) 0-10Post-Flow Time (Sec) 0-10Base Current % 20-90Pulse Frequency (Hz) 0.5-300Pulse Duty Cycle% 10-90Remote Control YesArc-Leading HF Start

Efficiency (%) 85Load Duty Cycle TIG 300A – 20% MMA 250A – 20%TIG 190A – 100% MMA 160A – 100%Power Factor 0.93Insulation Class FProtection Class IP21SWeight (kg) 37Dimensions (mm) 560 x 365 x 355Machine Package Includes SR26-4m TIG Torch / 4m Earth Lead / Argon RegulatorGas Hose / 315P AC/DC Machine

40

SE

CTIO

N O

NE

– M

AC

HIN

ES

Hypertherm remains the first choice of the metal cutting professional because of the company’s exclusive focus in making the best high-temperature and material processing technologies in the world. Recognised as the worldwide leader in the plasma technology, Hypertherm was the first plasma cutting equipment company to earn ISO 9001 registration.

Patented technologies allow Hypertherm Powermax systems to maximize cut quality, speed, and consumable parts life, which advanced circuitry optimizes power delivery.

Durability and safety are assured even in the most demanding work environments.

Hypertherm’s vast engineering resources and unparalleled product support contribute to improvements in performance, value and reliability.

Powermax systems are backed by Hypertherm’s full three-year power supply warranty and one-year torch warranty. No parts excluded. Examine competitive policies closely.A Word On Capacity RatingsThe recommended capacity is the target thickness of steel (other metals require an approximate 10-20% de-rating) allowing good productivity and quality (generally cutting speeds of 20 inches {500mm} per minute or faster).

At the maximum capacity, a good quality cut is still possible (10 inches {250mm} per minute), but reduced productivity means that no more than 20% of cutting should be in this thickness range. The severance capacity indicates the thickness that can be reasonably severed, but with poor cut quality and at very slow speeds. There is no industry standard for capacity ratings; be sure to understand the basis for competitive claims.

Duty CyclesHypertherm duty cycle ratings are established at 40ºC (104ºF), according to international standards, and are determined at actual cutting arc voltage levels. Competitive systems are often rated at room temperature (20ºC) and at theoretical output voltages, causing duty cycle ratings to be significantly overstated. CE ComplianceAll Hypertherm manual plasma systems sold in Australia are compliant with Australian CE standards.

WarrantyHypertherm Powermax systems come with a three year warranty on the power supply and one year on the torch and leads.

HYPERTHERM MANUAl PlASMA CUTTING SYSTEMSThe Performance Standard For Plasma Cutting

HYPERTHERM POWERMAx30®

PN: 088005 Standard package

PN: 088006 Deluxe package

The new Hypertherm Powermax 30 is set to exceed customer expectations, with its cutting capacities, reliability and rugged design. A completely new design, engineered from the ground up, the Powermax 30 sets the industry standard for a highly portable, easy to use plasma cutting system.

With highly advanced inverter technology, the Powermax 30 has unsurpassed power in its class and an unequalled industrial duty cycle rating, while weighing only 9kgs- 60% lighter than previous systems in its category.

POWER SUPPLY FEATURESDual voltage (120/230V, 1-PH, •50/60Hz)30amps, 2.49KW output•No air regulator required•Boosted open circuit voltage•Consumables storage compartment•Active electronic pilot arc controller•ISO 9001 and CE compliant•

SYSTEM SPECIFICATIONInput voltages 115/230V, 1-PH, •50/60Hz, CEInput current 230V 13.5A•Output voltage 83VDC•Output current 13.5-30A•Maximum OCV 240VDC•Gas supply – Air•Air flow rate 129 ltr/Min•Flow pressure 80psi (5.5bar)•Weight 9kg•

Duty Cycle Rating30 Amps @ 50%•

Cut CapacityHand:

Recommended: 1/4” (6mm)•Maximum: 3/8” (10mm)•Severance: 1/2” (12mm)•

Gouging: Not recommended•

T30V Torch & Consumable FeaturesSuitable to Push/Drag on work piece•Safety trigger•Contact-start arc initiation•HyLife electrode technology•Shielded front-end consumables•

For torch parts, please refer to page 229

41

SE

CTIO

N O

NE

– MA

CH

INE

S

PN: HPM 1000

The Powermax1000® G3 Series™ is ideally suited for use in metal service centres, metal scrapping and dismantling, industrial construction, welding repair services, industrial equipment manufacturing and repair, commercial ship manufacturing and repair, truck and trailer manufacturing and repair, farming and logging and vocational training.

POWER SUPPLY FEATURES60 amps, 8.4kW output•Auto-voltage circuit•Boost conditioner circuit•Standard CNC interface•Pilot arc controller with deactivation •switchDual-threshold pilot arc circuit•ISO 9001 and CE compliant•

SYSTEM SPECIFICATIONAuto input voltages 230-400V, 3-PH, •50/60 Hz, CEInput current 415V 15A•Output voltage 140VDC•Output current 20-60A•Maximum OCV 300 VDC•Gas supply – Air or N2•Flow rate 400 scfh (189l/min)•Flow pressure 70 psi (4.8bar)•83lbs (37kg)•

Duty Cycle Rating60 Amps @ 50% 230-600V 3-PH•

Cut CapacityHand:

Recommended: 3/4” (19mm)•Maximum: 1” (25mm)•Severance: 1 1/4” (32mm)•

Machine:Recommended: 3/8” (10mm)•Maximum: 1/2” (12mm)•

Gouging:Metal Removal Rate Air 10.0lbs/hr • (4.5kg/hr)

T60 and T60M Torch & Consumable Features

Safety trigger•ETR (Easy Torch Removal)•Contact-start arc initiation•HyLife electrode technology•Coaxial-assist jet technology•Shielded front-end consumables•

For torch parts, please refer to page 234.

PN: HPM 45

The Powermax45® with its small size and light weight provides unmatched portability among ½” (12mm) machines. Conical Flow™ increases arc energy density for superior cut quality with little dross. Easy to use patented drag cutting.

POWER SUPPLY FEATURES32A output•Auto-voltage circuit•Boost conditioner circuit•CNC interface•

SYSTEM SPECIFICATIONInput voltages 200–240V, 1-PH, 400V •3-PHInput current 200–240V, 34–28A 1-PH, •400V, 10A 3-PHOutput voltage 132VDC•Output current 20-45A•Maximum OCV 275 VDC•Gas supply – Air or N2•Flow rate 360 scfh (170l/min)•Flow pressure 90 psi (6.2bar)•15.8kg with torch•

Cut CapacityHand:

Recommended: 1/2” (12mm) •Maximum: 3/4” (19mm) •Severance: 1” (25mm)•

Machine:Maximum: 3/8” (10mm)•

Gouging:Metal Removal Rate Air 6.2lbs/hr • 2.8kg/hr

T45V and T45M Consumable FeaturesFast connect torch connection•Dual angle design•Powercool™ design•


HYPERTHERM POWERMAx 45


42

SE

CTIO

N O

NE

– M

AC

HIN

ES PN: HPM 1250

The Powermax1250® G3 Series™ is ideal for use in metal service centres, metal scrapping and dismantling, industrial construction, welding repair services, industrial equipment manufacturing and repair, commercial ship manufacturing and repair, truck and trailer manufacturing and repair, farming and logging and vocational training.

POWER SUPPLY FEATURES80 amps, 12kW output•Auto-voltage circuit•Boost conditioner circuit•Standard CNC interface•Pilot arc controller with deactivation •switch Dual-threshold pilot arc circuit•ISO 9001 and CE compliant•

SYSTEM SPECIFICATIONAuto input voltages 230-400V, 3-PH, •50/60 Hz, CEInput current 415V 21A•Output voltage 150VDC•Output current 25-80A•Maximum OCV 300VDC•Gas supply – Air or N2•

Flow rate 550scfh (260 l/min)•Flow Pressure 70 psi (4.8bar)•96.6lbs (44kg)•

Duty Cycle Rating80 Amps @ 60% 230-600V 3-PH•

Cut CapacityHand:

Recommended: 7/8” (22mm)•Maximum: 1 1/8” (29mm)•Severance: 1 1/2” (38mm)•

Machine: Recommended: 3/8” (10mm)•Maximum: 5/8” (16mm)•

Gouging:Metal Removal Rate Air 12.2lbs/hr • (5.5kg/hr)




PN: HPM 1650

The Powermax1650® G3 Series™ is suitable for use in metal service centres, metal scrapping and dismantling, industrial construction, welding repair services, industrial equipment manufacturing and repair, commercial ship manufacturing and repair, truck and trailer manufacturing and repair, farming and logging and vocational training.

POWER SUPPLY FEATURES100 amps, 16kW output•Auto-voltage circuit•Boost Conditioner circuit•Standard CNC interface•Pilot arc controller with deactivation •switchDual-threshold pilot arc circuit•ISO 9001 and CE compliant•

SYSTEM SPECIFICATIONSAuto input voltages 230-400V, 3PH, •50/60 Hz, CEInput current 400V 27 A•Output voltage 160VDC•Output current 30-100A•Maximum OCV 300 VDC•Gas supply – Air or N2•Flow rate 550scfh (260 l/min)•Flow pressure 175psi (5.1bar)•128.0lbs (58kg)•

Duty Cycle Rating100 Amps @ 80% 400-600V•

Cut CapacityHand:

Recommended: 1 1/4” (32mm)•Maximum: 1 1/2” (38mm)•Severance: 1 3/4” (44mm)•

Machine: Recommended: 1/2” (12mm)•Maximum: 3/4” (19mm)•

Gouging:Metal Removal Rate Air 22.8lbs/hr • (10kg/hr)






43

SE

CTIO

N O

NE

– MA

CH

INE

S

PN: MAX 200

The Max200® is suitable for use in metal service centres, metal scrapping and dismantling yards, industrial workshops, engineering workshops and commercial ship manufacturing and repair workshops.

POWER SUPPLY FEATURES200 amps, 30kW output•Dual gas operation •100% duty cycle at full power•Integrated coolant tank and pump•Leads up to 45m long available•With wheels as standard•Chopper based power supply•ISO 9001 and CE compliant•High productivity – Low cost operation•

SYSTEM SPECIFICATIONInput voltages 415V, 3-PH, 50Hz, CE•Input current 415V 52A•Output voltage 150VDC•Output current 40-200 A•Maximum OCV 280VDC•Plasma gas supply – Air, N2, O2, Air-Hz•Shield gas supply – Air, N2, O2•Plasma flow rate 66scfh (31 l/min)•Shield flow rate 280scfh (132 l/min)•Plasma flow pressure 120psi (8.3bar)•Shield flow pressure 90psi (6.2bar)•780.0 lbs (351kg)•

Duty Cycle Rating200 Amps @ 100%•

Cut CapacityHand:

Recommended: 1 1/2” (38mm)•Maximum: 2” (50mm)•Severance: 2 1/2” (64mm)•

Machine:Recommended: 1” (25mm)•Maximum: 2” (50mm)•

Gouging:Metal Removal Rate H35 46.0lbs/hr • (21kg/hr)

PAC200T and PAC200E Torch & Consumable Features

Safety trigger•High frequency starting•Water cooled torch•Ergonomic torch design•Safety retaining cap “in place” sensor •circuitShielded front-end consumables•



HYPERTHERM MANUAl PlASMA CUTTING SYSTEM ACCESSORIES

SPECIFICATION 30 45 600 1000 1250 1650 MAX 200

Air filtration kit N/A 128647 128647 128647 128647 128647 128647

Hand gouging heat shield

N/A 128658 N/A 128658 128658 128658 128658

Wheel kit N/A – N/A 128378 128646 128646 128788

Circle cutting guide

027668 027668 027668 027668 027668 027668 027668

Leather torch sheathing

024548 024548 024548 024548 024548 024548 024548

FineCut consumables kit

N/A 128889 N/A 128887 128888 128888 128888

Plasma cutting face shield

127103 127103 127103 127103 127103 127103 127103

ACCESSORIES

To obtain the best possible performance Hypertherm have a range of products to optimise your system. These products are designed to enhance your plasma cutting experience and obtain the maximum life from the consumables.

AVAILABLE PRODUCTS

Air filtration kitA ready-to-install kit with a .85 micron filter to protect against contaminated air, as well as an autodrain moisture separator.Hand gouging heat shieldProvides additional protection in gouging operations.

Circle cutting guideFacilitates consistent and accurate measured circles in work pieces. Also used as a stand-off guide in bevelling applications.Wheel kitA complete, pre-assembled kit for added mobility when the machine must be moved.FineCut consumables kitFor superior cut quality on thin plate, mild and stainless steel.Leather torch sheathingAvailable in 25-foot sections, this option provides additional protection for torch leads against burn-through and abrasion.

Circle cutting guide

FineCut consumables kit

Air filtration kit

Wheel kit

Hand gouging heat shield

Leather torch sheathing

Plasma cutting face shield

44

SE

CTIO

N O

NE

– M

AC

HIN

ES

HYPERTHERM AUTOMATION

45

SE

CTIO

N O

NE

– MA

CH

INE

SACCESSORIES

46

SE

CTIO

N O

NE

– M

AC

HIN

ES

HYPERTHERM GENUINE ACCESSORIES

47

SE

CTIO

N O

NE

– MA

CH

INE

SPROARC SYSTEM

WELDING POSITIONERS AND TURNING ROLLS

E.Z. arc system is a combination of positioners and turning rolls in bench design. You have a wide choice of components to create great flexibility in your automatic welding system. You are also able to change components easily to minimize the setup time. The special capability of E.Z. Arc system will help you produce high quality circumferential welds and provide the advantage of fast pay-back, safety and less worker fatigue, which will exactly meet your needs.

FEATURESCE conformity•Standard 38.5mmØ through-hole for gas purge•Remote foot switch – Run / Stop control•All units are high frequency protected•Additional speed ranges available on special order•U-Type is a special design for 0~90º circumferential welding and can be used for •weldments size up to max. 300mmØ with 300mm L.

HOW TO ORDER

ExamplePT-100A L 12Model No. Types Rail LengthPT-100A L=Lathe 06, 12, 15, 18PT-100B R=Roll PT-200A S=Standard PT-200B U=Universal

E.Z. ARC COMPONENTS

1. SL-0502. AH-035 / VH-0353. IS-3004. PG-150 / 450L5. CB-001 / 002 / 0076. CB-001V / VSFC-1K7. 1712W / 1715W / 1718W8. 20-248 / 10-613

48

SE

CTIO

N O

NE

– M

AC

HIN

ES SPECIFICATIONS

ProArc builds a full line of improved welding positioners from 100kg to 20,000kg and turning rolls from 1,000kg to 120,000kg for your needs. On special requirements, ProArc can supply custom design equipment for your job.

Fig.No.

Part No. Description / Specification Type

S R L U1 1106 Base rail, 600mm long 1*

1112 Base rail, 1200mm long 1* 1*1115 Base rail, 1500mm long 1118 Base rail, 1800mm long 4095 Main bracket 1

2 2050 Mounting rail, 500mm long 1 1 11065 Mounting rail, 650mm long 1

3 2110 End bracket 1 1 12280 End bracket 1

4 3075 Column tube, 750mm long 1 1 13064 90° column tube, 600mm x 400mm 1

5 2005 Support bracket 1 1 12004 Support bracket 1

6 2054 Cross bracket 1 1 12044 Cross bracket 1

7 3040 Boom tube with mounting pad, 400mm long 1 1 1 18 SL-050 Slide, 50mm stroke

SL-075 Slide, 75mm stroke 2 2 2 29 AH-035 Any angle holder, Ø 15-35mm

VH-035 V-Block torch holder, Ø 15-35mm 1 1 1 110 IS-300 Idler stand, Ø 30-300mm 111 TS-075 Tailstock, 75mm stroke 1

TS-075S Tailstock, 75mm stroke 1

Options:12 PG-150 3-Jaw chuck, OD 4-150mm (Centering adaptor included)

PG-450L 3-Jaw chuck, OD 4-450mm (Centering adaptor included)13 TA-100 Pneumatic torch actuator, 100mm stroke

TL-100 Pneumatic torch lift, 22.5° lift angle14 CB-001 Standard control box

CB-002 Sequencer, start delay/overlap controlled by original sensor setting

CB-007 Sequencer, intergrate pneumatic tailstock, torch lift and table rotation in one process

CB-001V Variable speed remote control boxVSFC-1K Variable speed foot control

15 1712W Welding table with wheels, 1200mm x 600mm1715W Welding table with wheels, 1500mm x 600mm1718W Welding table with wheels, 1800mm x 600mm

16 20-248 Reducer, speed range 0.5–8rpm for PT-100/20020-249 Reducer, speed range 1–12rpm for PT-100/20010-613 Jig adaptors, 3 x 6.5mmØ (P.C.D. 50mm) mounting hole

with a 38.5mmØ x 5mm (D) pilot hole

PROARC ACCESSORIES

R-Type

L-Type

S-Type

U-Type

49

SE

CTIO

N O

NE

– MA

CH

INE

S

SPECIFICATIONS & DIMENSIONS

Model Unit PT-100 PT-200Power input ~ 1 phase 110 / 220V 50/60HzCapacity (horizontal/vertical) kg 100 / 60 200 / 130Rated centre of gravity mm 50Rated eccentricity mm 50Table dimension (D) mm 320Rotation speed rpm A: 1-15 B: 0-4 (other speed available)Spindle thru hole mm 38.5Table slot bolt size – M10Earthing amp 200 @ 100%, 300 @ 40%Rotation motor hp 1/20 1/12Tilt range deg 0-120 0-120Welding timer sec 0-60Overall length ( A ) mm 420Overall width ( B ) mm 435Overall height ( C ) mm 340Centre to floor ( E ) mm 250Net weight kg 40.3 42.6Gross weight kg 43 45.3

Model Unit PT-100 PT-200 TR-3504Power input ~ 1 ph110/220V

50/60Hz1 ph220V 50/60Hz

1 ph220–240V 50/60Hz

Turning capacity kg 1000 3500 3500Load capacity (Drive + Idler) kg 1000 3500 3500Diameter range ( F ) mm 20-800 9-1400 9-1400Speed range mm/min 80-1600 60-1200 60-1200Rotation motor hp 1/12 1/2 1/2Roller dia. ( D ) mm 200 200 200Roller width ( E ) mm 50 100 100Roller type - PU PU PUOverall length ( A ) (Drive / Idler) mm 320 / 160 425 / 280 425 / 280Overall width ( B ) (Drive / Idler) mm 542 / 450 780 / 700 780 / 700Overall height ( C ) mm 335 520 520Net weight (Drive /Idler) kg 37 / 17 110 / 55 110 / 55Gross weight kg 58 185 185

PROARC SYSTEM

ProArc PT series positioners provide steel fabrication shops to position the jobs for ‘downhand’ position in the shortest possible time without the use of cranes and manpower. The constructions of ProArc positioners provide safe operation and long trouble-free service.

FEATURESCapacities range from 100 to 20,000 •kilograms360 degree rotation, 135 degree tilt •rangeHigh frequency protected•Machined “T” slots table with pilot and •through holeA.C. variable frequency drive to •rotationTile motors are electrically activated •mechanical AC brake motorsHigh quality worm gear reducers •for smooth operation and minimal backlashMaintenance-free grounding system•AD type adjustable table height •availableForward-Stop-Reverse and variable •speed control are standard

OPTIONSFast/Slow footswitch•Digital tachometer•Welding grounds•Grippers•

50

SE

CTIO

N O

NE

– M

AC

HIN

ES

PROARC POSITIONERS – PT SERIES

Mod

elU

nit

PT-

100A

/BP

T-20

0A/B

PT-

450/

450M

PT-

750

PT-

1500

PT-

3000

PT-

5000

PT-

10K

PT-

15K

PT-

20K

Pow

er in

put

–1

phas

e 11

5/23

0V 5

0/60

Hz

1 P

hase

220

–24

0V 5

0/60

Hz

3 ph

ase

220/

380V

50/

60H

z

Cap

acity

(hor

izon

tal/

verti

cal)

kg10

0/60

200/

130

450/

300

700/

500

1500

3000

5000

1000

015

000

2000

0

Rat

ed c

entre

of g

ravi

tym

m-

-50

/-30

030

030

030

030

030

030

0R

ated

ecc

entri

city

mm

5050

150

300

300

300

300

300

300

300

Tabl

e di

men

sion

( D

)m

m32

032

045

060

080

010

0012

0015

00(S

)17

50(S

)20

00(S

)R

otat

ion

spee

drp

n1.

5-15

/ 0.

4-4

1.5-

15 /

0.4-

40.

12-2

.50.

05-1

0.05

-10.

05-1

0.04

-0.8

0.02

-0.5

0.01

-0.2

50.

01-0

.25

Spi

ndle

thru

hol

em

m38

.538

.525

2525

2525

5050

50Ta

ble

pilo

t hol

e di

a.*d

epth

mm

––

50*5

50*5

50*5

75*5

75*5

100*

510

0*5

100*

5Ta

ble

T-sl

ot b

olt s

ize

–M

10M

10M

12M

12M

16M

20M

24M

30M

30M

30E

arth

ing

amp

200

200

400

400

800

800

800

800

800

800

Rot

atio

n m

otor

hp1/

201/

121/

61/

21

23

35

7.5

Tilt

mot

orhp

––

1/6/

-1/

41/

21

35

7.5

10Ti

lt ra

nge

deg

0-12

00-

120

0-13

50-

135

0-13

50-

135

0-13

50-

135

0-13

50-

135

Tilt

spee

d (1

35 d

eg.)

sec

––

3845

5865

6590

9090

Wel

ding

tim

erse

c0-

600-

600-

60–

––

––

––

Ove

rall

leng

th (

A )

mm

420

420

630

920

1150

1500

1600

1800

2000

2200

Ove

rall

wid

th (

B )

mm

435

435

650

875

1000

1200

1400

1800

2100

2400

Ove

rall

heig

ht (

C )

mm

340

340

630

720

990

1100

1200

1500

1650

1800

“Cen

tre to

floo

r ( E

) (A

D ty

pe)”

mm

250

250

540

(5

40-9

15)

600

(600

-975

)85

0 (8

50-1

300)

940

(940

-154

0)10

00

(100

0-18

00)

1250

(1

250-

2050

)14

00

(140

0-24

00)

1550

(1

550-

2550

)W

eigh

tkg

40.3

42.6

134

323

750

1800

2800

4200

5300

6500

*Man

ual t

ilt (P

T-45

0M) *

*Lar

ger c

apac

ity m

odel

as

requ

est

51

SE

CTIO

N O

NE

– MA

CH

INE

S


Model Unit TR-0100 TR-3504 TR-1000B TR-3500B TR-6000BPower input ~ 1 phase

115/230V 50/60Hz

1 phase 220-240V 50/60Hz

1 phase 115/230V 50/60Hz

1 phase 220-240V 50 / 60Hz

Rating amp 0.4/0.2 6 0.4/0.2 6 6Turning capacity kg 1000 3500 1000 3500 6000Load capacity (drive & idler) kg 1000 3500 1000 3500 6000Diameter range ( F ) mm 20-800 9-1400 50-3000Speed range mm/min 80-1600 60-1200 60-1200Rotation motor hp 1/12 1/2 1/8 1/2 1/2Roller diameter ( D ) mm 200 200Roller width ( E ) mm 50 100 50 100 150Roller type – PU PUOverall length ( A ) (drive/idler) mm 320/160 425/280 1410/1260 1600/1260 1750/1260Overall width ( B ) (drive/idler) mm 542/450 780/700 300/280 370/330 520/450Overall height ( C ) mm 335 520 425Weight (drive/idler) kg 37/17 110/55 57/40 102/69 150/92

FEATURESCapacities range from 1,000 to 6,000 •kilogramsFor pipes or vessels rotation•Metallic rollers are bounded with •polyurethaneQuick, accurate roll centering •adjustmentHand pendant with Forward-Stop-•Reverse, speed potentiometer and fast button are standardTR-0100 & TR-1000B are solid-state •controls with dynamic braking on the rotation drivesTR-3504, TR-3500B & TR-6000B are •AC inverter driveHigh frequency protected•Fast/Slow footswitch – optional•

PROARC TURNING ROllS – TR / TR-B SERIES

52

SE

CTIO

N O

NE

– M

AC

HIN

ES FEATURES

Capacities range from 15,000 to •240,000 kilogramsMain base frames are fabricated and •stress relieved before machiningSuperior worm gears & helical drive •gears are designed to provide high torque and low backlashSynchronized AC inverter drive control •for two motorsMetallic rollers are bounded with •natural rubberTR-K series designed with •symmetrical roller for quick and accurate centering adjustmentTR-KB series are bolt type for •diameter adjustmentHand pendant with Forward-Stop-•Reverse, speed potentiometer and fast button are standardHigh frequency protected•Fast/Slow footswitch – optional •

PROARC TURNING ROllS – TR-K / TR-KB SERIES


Unit TR-15K TR-15KB

TR-30K TR-30KB

TR-45K TR-45KB TR-60KB TR-90KB TR-135KB TR-240KB

Voltage & frequency 3 phase 220/380V 50/60Hz

3 phase 220/380V 50/60Hz

3 phase 220/380V 50/60Hz

3 phase 220/380V 50/60Hz

3 phase 220/380V 50/60Hz

3 phase 220/380V 50/60Hz

3 phase 220/380V 50/60Hz

Turning capacity kg 15000 30000 45000 60000 90000 135000 240000Load capacity (drive & idler) kg 10000 20000 30000 40000 60000 90000 160000Diameter range ( F ) mm 300-4700 300-4700 300-4700 300-4700 300-6500Speed range mm/min 100-1500 100-1500 100-1500 100-1350 100-1300 100-1200 100-1100Rotation motor hp 1/2*2 1*2 1.5*2 1.5*2 1.5*2 2*2 3*2Roller diameter ( D ) mm 405 405 405 405 500Roller width ( E ) mm 125 200 250 300 350 525 700Roller type – Rubber Rubber metal Rubber metal Rubber metal Rubber metal Rubber metal Rubber metalOverall length ( A ) (drive/idler) mm 590/385 695/470 740/520 800/570 1200/1100Overall width ( B ) (drive/idler) mm 2500/2200 2500/2200 2500/2200 2500/2200 3500Overall height ( C ) mm 625 625 625 625 750

53

SE

CTIO

N O

NE

– MA

CH

INE

SPROARC HANdSTOCK-TAIlSTOCK POSITIONERS – HTS SERIES

FEA

TU

RE

SA

ll w

elde

d st

eel f

ram

e st

ruct

ure

•Fo

r lon

g w

eldm

ents

rota

tion

•C

apac

ities

rang

e fro

m 5

00 to

20,

000

•ki

logr

ams

Mac

hine

“T”

slo

ts ta

ble

with

pilo

t and

•

thro

ugh

hole

A.C

. inv

erte

r driv

e fo

r rot

atio

n•

Forw

ard-

Sto

p-R

ever

se a

nd v

aria

ble

•sp

eed

cont

rol a

re s

tand

ard

Tota

lly g

ear-s

afe

desi

gn•

Mai

nten

ance

-free

gro

undi

ng s

yste

m•

Opt

iona

l adj

usta

ble

tabl

e he

ight

to fi

t •

larg

er w

ork

piec

e

SP

EC

IFIC

AT

ION

S &

DIM

EN

SIO

NS

Mod

el -

Hea

d &

Tai

lsto

ckU

nit

HTS

-600

HTS

-100

0H

TS-3

000

HTS

-600

0H

TS-1

0KH

TS-1

5KH

TS-2

0KM

ax. t

otal

cap

acity

Kg

600

1000

3000

6000

1000

015

000

2000

0H

S-H

eads

tock

/ TS

-Tai

lsto

ck-

HS

-300

TS-3

00H

S-5

00TS

-500

HS

-150

0TS

-150

0H

S-3

000

TS-3

000

HS

-500

0TS

-500

0H

S-5

000

TS-5

000

HS

-10K

TS-1

0KPo

wer

inpu

t-

1 ph

ase

220V

50

/60H

z

-3

phas

e 22

0/38

0V

50/6

0Hz

-3

phas

e 22

0/38

0V

50/6

0Hz

-3

phas

e 22

0/38

0V

50/6

0Hz

-3

phas

e 22

0/38

0V

50/6

0Hz

-3

phas

e 22

0/38

0V

50/6

0Hz”

-3

phas

e 22

0/38

0V

50/6

0Hz

-

Cap

acity

kg30

030

050

050

015

0015

0030

0030

0050

0050

0075

0075

0010

000

1000

0R

ated

cen

ter o

f gra

vity

( E

)m

m30

030

030

030

030

030

030

0E

ccen

tric

load

torq

ue ra

ting

kg-c

m90

00-

1500

0-

4500

0-

9000

0-

1500

00-

2250

00-

3000

00-

Tabl

e di

men

sion

( B

)m

m45

060

075

0 *

750

1000

* 1

000

1200

* 1

200

1500

* 1

500

1500

* 1

500

Rot

atio

n sp

eed

rpm

0.12

-2.5

-0.

15-1

.5-

0.1-

1-

0.05

-1-

0.04

-0.8

-0.

04-0

.8-

0.04

-0.8

-Ta

ble

pilo

t hol

e di

a.*d

epth

mm

25*T

hru

Hol

e25

*Thr

u H

ole

100

* 6

100

* 6

100

* 6

125

* 6

125

* 6

Tabl

e sl

ot b

olt s

ize

-

M12

M

12

M16

M

16

M24

M

30

M30

Ear

thin

gam

p40

040

040

040

060

060

060

060

060

060

060

060

060

060

0R

otat

ion

mot

orhp

1/6

-1/

6-

1/2

-1

-1-

1/2

-2

-2

-O

vera

ll le

ngth

( A

)m

m60

075

090

010

0011

5013

5013

50O

vera

ll w

idth

( B

)m

m45

060

010

0011

0012

0015

0015

00O

vera

ll he

ight

( C

)m

m82

510

0011

7513

0016

0020

0020

00C

ente

r to

floor

( D

)m

m60

070

080

080

010

0012

5012

50B

olt-d

own

base

( H

)m

m50

065

080

095

010

5012

5012

50B

olt-d

own

hole

dia

.*sq

uare

mm

20*4

5020

*600

20*7

5024

*900

28*1

000

28*1

200

28*1

200

54

SE

CTIO

N O

NE

– M

AC

HIN

ES PN: 63 100

DUCT PN: 5M 93.070.0005 45mm Ø

DUCT PN: 10M 93.070.0006 45mm Ø

Ultra light, flexible and powerful.These are only some properties of

this small power house. Two strong turbines provide an excellent suction efficiency and high static pressing. The minimum weight makes it very flexible and universal for so many uses.

A KemTex® EPTFE membrane filter cartridge provides the filtration of superfine dust below 0.1 µm. Thereby this unit is suitable for the separation of alveoli exchangeable dusts. The advantage of surface filtration is, that the filter cartridge can be cleaned. In case of the Dusty, this happens manually the minute when an essential cleaning will

be indicated by the instrument itself. The collected dust can easily be extracted from the lower part of the unit.

Different nozzles, welding torches with integrated extraction or mini exhaust arms of the extensive accessory program can be connected to the two lugs of this extraction and filter unit. The suction performance can be stepless and electronically controlled.

TECHNICAL DATA

Suction performance 340 m³/hMotor power 1.6kWVoltage 1 x 230V / 50HzNoise Level 74 dB (A)Filter efficiency > 99.9%Weight 21kgDimensions 300 x 300 x 690mm

KEMPER dUSTY

KEMPER FIlTER MASTER

PN: 64 100 100 2.0M, Ø 150MM

PN: 64 100 101 3.0M, Ø 150MM

PN: 64 100 102 4.0M, Ø 150MM

The Filter-Master, a mobile mechanical filter, is designed and ideally suited for use at various welding workplaces and conditions. Built of rigid sheet metal construction and incorporating anti corrosive powder coat finish, the Filter-Master is designed for every day use. Four heavy duty rubber casters allow ease of movement within the factory and the extraction arm can be swiveled by 360º. It is therefore very easy to direct the arm into any desired position. The Filter-Master is the ideal solution to your extraction problems.

The contaminated air captured by the extraction hood is separated from rough particles by a pre-filter. Thus, the pre-filtered air is directed through the subsequent main filter with a filter efficiency of more than 99.9% and the

clean air is fed back to the workshop by two lateral blow-grids integrated in the machine. A control light indicates a necessary change of the filter insert. To replace the filter, the top cover is folded back. The life expectancy of the filter is subject to the application of the Filter-Master.

When not in use the power can be stored on the cable holder provided. All necessary controls, indicators and instructions are shown on the detailed control panel.

TECHNICAL DATA

Fan performance 2.200m³/hSuction capacity 1.200m³/hMotor power 1.1kWVoltage 3 x 400V / 50HzNoise level 68dB (A)Filter efficiency > 99.9%Weight (without extraction arm) 80kgDimensions 655 x 655 x 1.020mm

55

SE

CTIO

N O

NE

– MA

CH

INE

S

PN: 62 100 100 2.0M Ø 150MM

PN: 62 100 101 3.0M Ø 150MM

PN: 62 100 102 4.0M Ø 150MM

The Filter Master XL is the basic type of filter units with highly efficient KemTex® ePTFE membrane filter cartridges.

A great advantage of the KemTex® ePTFE membrane filter cartridges – in addition to the high separation efficiency – is the possibility of cleaning them.

The control of the Filter Master XL monitors the collected dust on the surface of the filter media and indicates a necessary cleaning cycle.

The unit can be equipped with a 2m, 3m or 4m exhaust arm. Within its range, it can easily be brought in every position, which remains self-supporting.

The included KEMPER exhaust hood is rotatable by 360° and can be adapted to the welding joint because of its rectangular shape.

TECHNICAL DATA

Fan performance 3.000 m³/hExtraction performance at the hood 1.200 m³/hMotor power 1.5kWVoltage 3 x 400V / 50HzCompressed air 5 – 6 barNoise level 68dB (A)Filter efficiency > 99.9%Weight (without exhaust arm) 135kgDimensions 655 x 655 x 1.460mm

KEMPER ElECTROSTATIC FIlTER UNITS, MOBIlE

With one exhaust armUnits with flexible exhaust arms

PN: 86 100 100 2.0m, Ø 150mm

PN: 86 100 101 3.0m, Ø 150mm

PN: 86 100 102 4.0m, Ø 150mm

Units with rigid metal tube arms

PN: 86 100 103 2.0m, Ø 150mm

PN: 86 100 104 3.0m, Ø 150mm

PN: 86 100 105 4.0m, Ø 150mm

PN: 94 104 100 Automatic saturation control

Switches off the unit when the main filter is saturated.

PN: 92 919 Surcharge for activated charcoal filter

The KEMPER electrostatic filter unit is suitable for use at changing workplaces.

Bigger particles are captured in a pre-filter. The main filter works according to a two step-system of ionization and purification.

The remaining particles are carried with the airflow into the ionization wires

where they are positively charged.The collecting sheets in the main filter

are negatively charged and separate the particles from the air.

All operation functions as well as control lights for monitoring the high voltages operating control and the on/off switch are clearly arranged on the display. A connection port for the automatic start stop and lighting kit is also integrated into the display.

One exhaust arm with 2m, 3m or 4m length can be installed. Both, a rigid metal tube arm or flexible exhaust arm is available.

TECHNICAL DATA

Fan performance 2.200m³/hSuction capacity with 1 exhaust arm 1.200m³/hMotor power 1.1kWVoltage 3 x 400V / 50HzFilter efficiency > 98%Noise level ca, 68dB (A)Weight (without extraction arm) 105kgDimensions (W x D x H) 655 x 655 x 1.020mm.

KEMPER FIlTER MASTER xl

56

SE

CTIO

N O

NE

– M

AC

HIN

ES Lighting for the exhaust hood

Part.-Nr. Description79 103 015 Complete lighting set, 2 x 12V, 70W for units with one exhaust arm,

incl. on/off switch on the exhaust hood.79 103 016 Complete lighting set, 2 x 12V, 70W for units with two exhaust arms

inc. on/off switch on the exhaust hood.

Automatic start-stop

Part.-Nr. Description94 102 10 Automatic start-stop for units with 1 exhaust arm switches the

ventilator via a sensor connected to the earthing wire of the welding machine.

94 102 11 Automatic start-stop for units with 2 exhaust arms switches the ventilator via a sensor connected to the earthing wire of the welding machine.

Replacement hood

Exhaust hood as replacement for exhaust arms and telescopic exhaust arms, inc. swivel joint and required fasteningPart-Nr. Description79 103 00 Exhaust hood 79 103 010 Exhaust hood incl. lamps for lighting kit

Protective grating

Replacement grating for exhaust hoodPart-Nr. Description12 700 091 Grating as replacement for the exhaust hood

Replacement hoses for KEMPER flexible exhaust arms

Part-Nr. Description11 403 48 Length 2.0m for exhaust arms 2.0m, Ø 150mm11 403 49 Length 3.0m for exhaust arms 3.0m, Ø 150mm11 406 50 Length 4.0m for exhaust arms 4.0m. Ø 150mm

Replacement hoses for KEMPER rigid metal tube arms

Part-Nr. Description79 103 09 Set of replacement hoses (3pcs)79 103 010 Set of HT hoses (3 pcs) for up to + 310ºC

Spare filters for mechanical filter units

Part-Nr. Description10 900 33 Pre-filter mats (10 per set)10 900 10 Main filter10 900 05 Activated charcoal filter

Spare filters for electro-static filter units

Part-Nr. Description10 903 14 Pre and after filter set10 904 00 Filter cell for electrostatic filter unit10 900 05 Activated charcoal filter

Spare filters for cartridge filter units

Part-Nr. Description10 903 13 Spare filters for mobile cartridge filter unit10 903 00 Spare filter for Filter Master XL

KEMPER ACCESSORIES ANd SPARE PARTS FOR MOBIlE FIlTER UNITS

57

SE

CTIO

N O

NE

– MA

CH

INE

S

Welding tables

These extraction tables have been specially developed for handling of smaller metal workpieces.

The ergonomically, stable sheet steel construction and the robust material support enable a comfortable and safe functioning.

A dust collecting drawer allows a safe cleaning of the table. The welding tables which are available in different sizes, can be connected to fans or to a central extraction and filtration system.

Welding table

Stable welded steel table with multi layered paint, grating, dust collection drawer.Part-Nr. Description950 490 047 Table dimensions: w= 1000mm, d= 800mm, h= 850mm

connection spigot: diam. 160mm950 498 048 Table dimensions: w= 1500mm, d= 800mm, h= 850mm

connection spigot: diam 250mm950 498 049 Table dimensions: w= 2000mm, d= 800mm, h= 850mm

connection spigot: diam 250mm

Welding table with fan

Stable welded steel table with multi layered paint, grating, dust collection draw. The table is equipped with a direct driven fan at the side of the table.Part-Nr. Description95 021 111 Extraction capacity: 2200m³/h – 1.1kW – 3 x 400V – 50Hz Table dimensions: w= 1000mm. d= 800mm, h= 850mm95 021 112 Extraction capacity: 3000m³/h – 1.5kW – 3 x 400V – 50Hz Table dimensions: w= 1500mm. d= 800mm, h= 850mm95 021 113 Extraction capacity: 3000m³/h – 1.5kW – 3 x 400V – 50Hz Table dimensions: w= 2000mm. d= 800mm, h= 850mm

Suitable filter units

Part-Nr. Extraction volume Filter unit99 820 0047 2000m³/h 81 0200 25099 820 0048 2500m³/h 81 0350 25099 820 0049 3000m³/h 81 0300 250The airflow which is needed to connect several tables to a filter unit can be calculated by adding the required airflow per table.

KEMPER WEldING ANd CUTTING TABlES

KEMPER HANd PlASMA TABlES

PN: 197 0033 W800mm, D600mm, H800mm

PN: 197 0002 W1000mm, D800mm, H800mm

These extraction tables have especially been developed for the cutting of smaller workpieces.

The ergonomically adapted, stable sheet steel construction and the robust material support of flat steel enable a comfortable and safe functioning.

The table which is available in different sizes, can be connected to an extraction unit.

Hand plasma table

Solidly built hand plasma table with strong steel supports and grating for smaller cut out parts

58

SE

CTIO

N O

NE

– M

AC

HIN

ES

COMPRESSORS

PILOT CLASSIC K SINGLE PHASE

The Classic K Series is Pilot Air’s premium range of air compressors. Exceptional durability and efficiency make the K series suitable for any heavy duty, industrial use.FEATURES

Cast iron cylinders for longer life and quieter operation•Stainless steel valves, plus a balanced crank and flywheel for durability and •smooth operationMaximum operator protection. A fully enclosed steel belt-guard offers maximum •safety and also allows belts and pulleys to be inspected easilyNon-perishable copper discharge pipes for durability•Heavy duty rubber wheels and lifting handles designed to withstand heavy •working conditionsAuto stop/start pressure switch control•All 240V electric motors are equipped with overload protection•DIR AS1210-3 approved air receivers - the receivers incorporate separate outlets •for the safety valve, pressure switch, check valve and drain12 Mth warranty backed by a nationwide service network•

MODEL PIST.DISPL. MOTOR VOLTS CYLINDERS MAX.PRESS. RECEIVER APP.LITRES

SIZE (mm) L x W x H

APPROX. KG

CFM L/S HP KW PSI KPAK3/5 5.7 2.7 1.0 0.75 240v 1 145 1000 25 1050x400x700 45K8/8 8.0 3.7 1.5 1.1 240v 1 145 1000 45 1050x460x730 50K11/10 10.8 5.1 2.0 1.5 240v 2 145 1000 53 1200x460x740 55K11/12 12.0 5.7 2.25 1.65 240v 2 145 1000 53 1200x460x740 55K17/12 12.5 5.9 2.3 1.65 240v 2 145 1000 53 1200x460x780 60K17/15 15.8 7.4 2.7 2.0 240v/15A 2 145 1000 53 1200x460x780 60K17/15L 15.8 7.4 2.7 2.0 240v/15A 2 145 1000 96 1400x460x780 68K25/16L 16.0 7.5 2.7 2.0 240v/15A 2 145 1000 96 1400x460x900 68

PILOT TRADEMASTER SERIES

The Pilot Air range of Trademaster air compressors combine portability and maximum efficiency with Pilot’s established record for quality and reliability. The Trademaster series of air compressor is suited to those trades and occupations that need a reliable durable and portable source of air.FEATURES

Auto stop/start pressure switch controls on electric units•Auto idle down/unloading controls on petrol units•DIR AS1210-3 approved air receivers. The receivers incorporate separate outlets •for the safety valve, pressure switch, check valve and drainMax operator protection. A fully enclosed steel belt-guard offers maximum safety •and also allows belts and pulleys to be inspected easilyNon-perishable copper discharge pipes for durability•Heavy duty rubber wheels and lifting handles designed to withstand heavy •working conditionsFinned alloy cylinders ensure max heat dissipation while cast iron cylinder liners •result in max pump durabilityAll 240V electric motors are equipped with overload protection•Petrol model features Briggs and Stratton, Vanguard series motors•12 Mth warranty backed by a nationwide service network•

MODEL PIST.DISPL. MOTOR VOLTS CYLINDERS MAX.PRESS. RECEIVER APP.LITRES

SIZE (mm) L x W x H

APPROX. KG

CFM L/S HP KW PSI KPATM10 10 4.7 2.0 1.5 240v 2 145 1000 45 1050x460x720 50TM12 12 5.7 2.3 1.7 240v 2 145 1000 53 1200x460x720 55TM15 14.8 7.0 2.7 2.0 240v 2 145 1000 53 1200x460x720 55TM15P 14.8 7.0 5.5HP PET B&S N/A 2 145 1000 53 1200x460x800 58

59

SE

CTIO

N O

NE

– MA

CH

INE

SCOMPRESSORS

PILOT SILENCED SERIES

The Pilot Air range of Silenced air compressors provide the solution for sites subject to stringent environmental noise requirements. The Silenced series of air compressors combine noise reduction with the reliability and efficiency built into all Pilot Air compressors.FEATURES

Steel cabinets lined with acoustic foam to deaden noise and designed to maximise •cooling air flow through the cabinetThermostatically controlled cooling combined with over-temp protection ensure •correct temperature operation of the unitSteel cabinets feature a durable, powder coat finish•Cast iron cylinders and stainless steel valves provide a long life and a high level of •efficiency and reliabilityAll units feature auto stop/start control•Model K17SI features a regulated and non-regulated outlet to suit all installations•Model K25SI to K50SI models feature a touch-type control/diagnostic panel •complete with rotation protection, over-temp protection and indication for compressor and cooling fan operation.12 Mth warranty backed by a nationwide service network•

MODEL PIST.DISPL. MOTOR VOLTS CYLINDERS STAGES MAX.PRESS. SIZE (mm) L x W x H

d (B) A APPROX.

APPROX. KG

CFM L/S HP KW PSI KPAK17SI 15.8 7.4 3.0 2.2 415v 2 1 145 1000 730x640x1100 63 147K25SI 21 9.9 5.5 4.0 415v 2 2 174 1200 900x640x1100 65 168K30SI 32 15.1 7.5 5.5 415v 2 2 174 1200 900x640x1100 66 182K50SI 42 19.8 10.0 7.5 415v 2 2 174 1200 900x640x1100 68 220

Note: These units are not supplied with an air receiver, please contact us for details.

PILOT INDUSTRIAL THREE PHASE

The Pilot Air range of Industrial air compressors offers the reliability, efficiency and performance essential to satisfy the needs of the industry today.FEATURES

Cast iron cylinders and stainless steel valves – together they provide a long life, a •high level of efficiency and reliabilityMaximum heat dissipation from the use of industrial grade alloy cylinder heads, •aftercooler and intercoolersFor max efficiency, all two stage units feature both an aftercooler and intercooler, •this also gives the availability of higher pressure if required.T.E.F.C 415V/50HZ (3 phase) motors on all units, with overload protection•Auto stop/start control•DOL starter control on all models up to 10HP (7.5kw)•Star-delta starter standard on 15HP (115kw) and 20HP (15kw) models•DIR AS1210-3 approved air receivers•12 Mth warranty backed by a nationwide service network•

MODEL PIST.DISPL. MOTOR VOLTS CYLINDERS STAGES MAX.PRESS. RECEIVER APP.LITRES

SIZE (mm) L x W x H

APPROX. KG

CFM L/S HP KW PSI KPAK17T 15.8 7.4 3.0 2.2 415v 2 1 145 1000 53 970x440x780 70K25LI8 18 8.5 4.0 3.0 415v 2 2 160 1100 96 1400x440x900 90K25/21 21 9.9 5.5 4.0 415v 2 2 160 1100 147 1450x580x1050 152K30 32 15.1 7.5 5.5 415v 2 2 160 1100 147 1450x580x1130 185K50 42 19.8 10.0 7.5 415v 2 2 160 1100 216 1450x640x1300 260K60 61 28.8 15.0 11.0 415v V4 2 160 1100 267 1770x680x1260 295K100 77 36.3 20.0 15.0 415v V4 2 160 1100 316 2050x680x1260 398

60

SE

CTIO

N O

NE

– M

AC

HIN

ES PILOT PETROL INDUSTRIAL SERIES

The Pilot Air range of Petrol driven air compressors offers a reliable, durable and efficient range of units suitable for any size application. The petrol driven series is designed to withstand harsh conditions and to provide trouble free operation.FEATURES

Full engine idle-down control and unloading for an economical and long life•Easy starting in any conditions facilitated by an easy start air discharge relief valve•Cast iron cylinders and stainless steel valves provide a long life and a high level of •efficiency and reliability Honda motors on all models•2.5HP and 5.5HP models feature recoil type starting•9HP and 11HP models feature both electric and recoil start•DIR AS1210-3 approved air receivers•12 Mth warranty backed by a nationwide service network•

MODEL PIST.DISPL. CYLINDERS STAGES MOTOR HP

MAX.PRESS. RECEIVER APP.LITRES

SIZE (mm) L x W x H

APPROX. KG

CFM L/S PSI KPAK3P 8 3.7 1 1 2.5 145 1000 25 1050x400x710 56K11P 12 5.7 2 1 5.5 145 1000 53 1200x460x780 62K17P 16.5 7.8 2 1 5.5 145 1000 53 1200x460x800 65K25P 21 9.9 2 2 9.0 160 1100 96 1400x460x950 118K25LP 21 9.9 2 2 9.0 160 1100 147 1450x580x1050 158K30P 32 15.1 2 2 11.0 160 1100 147 1450x580x1090 185

COMPRESSORS

61

SE

CTIO

N O

NE

– MA

CH

INE

S

PART NUMBER: W20P / W20PE

HONDA 13HP or VANGUARD 14HP V-TWIN SPECIFICATIONS

Recoil or Recoil and Key start (Electric •start option)200 Amp AC Welder•Duty Cycle 100% @ 130Amps, 60% •@ 180Amps 30% @ 200Amps7.5kVA Single Phase Generator•850mm x 530mm x 575mm•90 Kgs•

PART NUMBER: W20PE/16

VANGUARD 16HP V-TWIN SPECIFICATIONS

Recoil and Key start•200 Amp AC Welder•Duty Cycle 100% @ 130Amps, 60% •@ 180Amps, 30% @ 200Amps8.0kVA Single Phase Generator•850mm x 530mm x 575mm•105 Kgs•

PART NUMBER: W22PDC

HONDA 13HP or VANGUARD 14HP V-TWIN SPECIFICATIONS

Recoil or Recoil and Key start•220 Amp DC Welder•Duty Cycle 100% @ 145Amps, 60% •@ 200Amps, 30% @ 220Amps5.0kVA Single Phase Generator•850mm x 530mm x 575mm•93 Kgs•

MEGAJET PETROl WEldER /GENERATORS AC & dC

MODEL ENGINE WELDER GEN kVA 3 Ph. kVA SIZE KGW20P Honda 13HP or Vanguard 14HP V-Twin 200 Amp AC 7.5 Nil 850 x 530 x 575mm 90W20PE Honda 13HP or Vanguard 14HP V-Twin Electric Start 200 Amp AC 7.5 Nil 850 x 530 x 575mm 95W20PE/16 Vanguard 16HP V-Twin Electric Start 200 Amp AC 8.0 Nil 850 x 530 x 575mm 105W22PDC Honda 13HP or Vanguard 14HP V-Twin 220 Amp DC 5.0 Nil 850 x 530 x 575mm 93W22PDCE Honda 13HP or Vanguard 14HP V-Twin Electric Start 220 Amp DC 5.0 Nil 850 x 530 x 575mm 98W22PDC/16 Vanguard 16HP Electric Start 220 Amp DC 5.0 Nil 850 x 530 x 575mm 125W30PDC Honda 24HP Electric Start 20L Fuel Tank 300 Amp DC 6.0 15.0 1100 x 580 x 750mm 175

PART NUMBER: W22PDCE

HONDA 13HP EL.START or VANGUARD 14HP V-TWIN EL.START SPECIFICATIONS

Recoil and key start•220 Amp DC Welder•Duty Cycle 100% @ 145Amps, 60% •@ 200Amps, 30% @ 220Amps5.0kVA Single Phase Generator•850mm x 530mm x 575mm•98 Kgs•

PART NUMBER: W22PDC/16

VANGUARD 16HP EL.START SPECIFICATIONS

Recoil and key start•220 Amp DC Welder•5.0kVA Single Phase Generator•Duty Cycle 100% @ 145Amps, 60% •@ 200Amps, 30% @ 220Amps850mm x 530mm x 575mm•125 Kgs•

PART NUMBER: W30PDC

HONDA 24HP EL.START SPECIFICATIONS

Long Range Fuel Tank 20L•300 Amp DC Welder•Duty Cycle 100% @ 190Amps, 60% •@ 270Amps, 30% @ 300Amps6.0kVA Single Phase Generator•15.0kVA Three Phase Generator•1100mm x 580mm x 750mm•175Kgs•

Premium Quality Italian alternator/welder ends combined with Honda or Vanguard petrol engines, make these portable, utility type generator/welders sturdy and reliable. All with brushless, capacitor excited alternators and thermal circuit breakers with double power points. Heavy wall tubular powder coated steel frames with isolation mounts.

62

SE

CTIO

N O

NE

– M

AC

HIN

ES

MEGAJET dIESEl WEldER /GENERATORS AC & dC

Premium Quality Italian alternator/welder ends combined with Yanmar or Hatz diesel engines, make these portable, utility type generator/welders sturdy and reliable. All with brushless, capacitor excited alternators and thermal circuit breakers with double power points. Heavy wall tubular powder coated steel frames with isolation mounts.

PART NUMBER: W20DE

YANMAR 10HP DIESEL EL.START SPECIFICATIONS180 Amp AC Welder•Duty Cycle 100% @ 120Amps, 60% @ 160Amps, 30% @ 180Amps•6.0kVA Single Phase Generator•850mm x 530mm x 575mm•120 Kgs•

PART NUMBER: W20DHE

HATZ 11HP DIESEL EL.START SPECIFICATIONS200 Amp AC Welder•Duty Cycle 100% @ 130Amps, 60% @ 180Amps 30% @ 200Amps•7.0kVA Single Phase Generator•850mm x 530mm x 575mm•140 Kgs•

PART NUMBER: W22DHE

HATZ 11HP DIESEL EL.START SPECIFICATIONS200 Amp DC Welder•Duty Cycle 100% @ 130Amps, 60% @ 180Amps 30% @ 200Amps•5.0kVA Single Phase Generator•850mm x 530mm x 575mm•145 Kgs•

PART NUMBER: W22DDC

HATZ 15HP DIESEL EL.START SPECIFICATIONSLong Range Fuel Tank 20L•220 Amp DC Welder•Duty Cycle 100% @ 145Amps, 60% @ 200Amps, 30% @ 220Amps•5.0kVA Single Phase Generator•1100mm x 580mm x 750mm•180 Kgs•

PART NUMBER: W30DDC

HATZ 20HP DIESEL TWIN CYLINDER EL.START SPECIFICATIONS300 Amp DC Welder•Duty Cycle 100% @ 190Amps, 60% @ 270Amps, 30% @ 300Amps•6.0kVA Single Phase Generator•15.0kVA Three Phase Generator•1100mm x 580mm x 750mm•240 Kgs•

MODEL ENGINE WELDER GEN kVA 3 Ph. kVA SIZE KGW20DE Yanmar 10HP Electric Start 180 Amp AC 6.0 – 850 x 530 x 575mm 120W20DHE Hatz 11HP Electric Start 200 Amp AC 7.0 – 850 x 530 x 575mm 140W22DHE Hatz 11HP Electric Start 200 Amp DC 5.0 – 850 x 530 x 575mm 145W22DDC Hatz 15HP Electric Start 20L Fuel Tank 220 Amp DC 5.0 – 1100 x 580 x 750mm 180W30DDC Hatz 20HP Twin Cylinder Electric Start 300 Amp DC 6.0 15.0 1100 x 580 x 750mm 240

OPTIONS Petrol & Diesel DESCRIPTIONELCB Earth leakage, M.E.N. 30m/amp circuit breaker on gen outlet to protect userIP66 Safety Outlet Kit Weatherproof outlets with sealed flaps x 2 plus ELCB trip protection as aboveVoltage Reduction Device (VRD)

Factory fitted safety device for Mining/Government sectors requiring output welding voltage reduction, safety code section 1674.2.2003

220 Amp DC Welder DC output to 220 Amps with 5kVA auxiliary genset. No battery charge facilityWheel Kit Pneumatic tyres and retractable handles

63

SE

CTIO

N O

NE

– MA

CH

INE

S

TIG BRUSH – WELD CLEANING SYSTEM

PN: TB-0250The TIG BRUSH SYSTEM has solved the access and burn through problems of hard electrodes, by replacing them with a brush. The unique brush design provides fast, high quality results even in the most inaccessible areas.

Lightning Fast Weld Cleaning•Best practice finish•Low running costs•OH & S compliant•Quick, safe cleanup•Works on all thicknesses•

Instant resultsThe even distribution of current going into the workpiece, plus the greater amount of cleaning solution held in the brush gives a faster and higher quality result. Work can be cleaned while the customer waits.Cleans all plate thicknessesVariable power adjustment gives the TIG Brush the unique ability to clean welds not only on thin gauges, but on materials of all thicknesses. Works on all grades of stainless steel and even brightens brass and copper.Environmentally FriendlyThe TIG Brush activates a very mild solution to get a faster, more thorough and gentler clean. Low voltage power minimises the risk of injury to operator and damage to work piece or other equipment.No Special Cleanup RequiredAfter a weld has been “TIG Brushed” it is rinsed with water. No harsh chemicals need to be dispersed of with expensive and slow procedures.Soft BrushThe soft and conductive bristles hold the solution and conform to any shape. The brush works equally well on flat surfaces, in tricky corners and deep crevices.Portable and CompactSmallest machine of its type. The TIG Brush is designed to go where needed, including remote work sites. Long leads and a light brush handle give unparalleled reach and flexibility.Low Running Costs

Long lasting brush•Low cost consumables•Fast clean up•Proprietary design means low power input yields high power results•

Robust and SimplePurpose built plastic case protects the electronics from bumps and spills. Simple controls provide 9 different settings. Handy tips are provided in the user’s manual.

TIG BRUSHES

PN: TB-1006 Screw in Long Life Tig brushesPN: TB-1006/10 Packet of 10 Screw in Long Life Tig brushesPN: TB-0027 Tig brush shroud PN: TB-2001 1lt Cleaning SolutionPN: TB-2005 5lt Cleaning Solution

64

SE

CTIO

N O

NE

– M

AC

HIN

ES

Documents

01 Machines