file · Web viewSECTION 09 96 00. TEXTURED AND HIGH BUILD COATINGS. Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2018 - 2018 ARCAT, Inc

SECTION 09 96 00TEXTURED AND HIGH BUILD COATINGS

Display hidden notes to specifier. (Don't know how? Click Here)

Copyright 2018 - 2018 ARCAT, Inc. - All rights reserved

1 GENERAL

1.1 SECTION INCLUDES

1.1.1 Textured and high-build coatings of the following types:1.1.1.1 Heat reflective exterior wall coating systems.1.1.1.2 Heat reflective roof and metal coating systems.1.1.1.3 Heat reflective concrete and wood deck coating systems.1.1.1.4 Architectural textured and smooth high build coatings.1.1.1.5 Top coats.1.1.1.6 EIFS finishes.1.1.1.7 Penetrant sealers - water repellents and stains.1.1.1.8 Anti-graffiti coating systems.1.1.1.9 Carwash coating systems.1.1.1.10 Primers.1.1.1.11 Block fillers and patching compounds.

1.2 RELATED SECTIONS

1.2.1 Section 03 30 00 - Cast-in-Place Concrete.

1.2.2 Section 04 20 00 - Unit Masonry.

1.2.3 Section 05 12 13 - Architecturally-Exposed Structural Steel Framing.

1.2.4 Section 05 50 00 - Metal Fabrications.

1.2.5 Section 06 20 00 - Finish Carpentry.

1.2.6 Section 06 40 00 - Architectural Woodwork.

1.2.7 Section 08 11 13.13 - Standard Hollow Metal Doors and Frames.

1.2.8 Section 09 21 16.33 - Gypsum Board Area Separation Wall Assemblies.

1.2.9 Section 22 05 00 - Common Work Results for Plumbing.

1.2.10 Section 26 05 00 - Common Work Results for Electrical.

1.3 REFERENCES

1.3.1 ASTM International (ASTM):1.3.1.1 ASTM B117-95 - Standard Practice for Operating Salt Spray (Fog) Apparatus.

Salt Spray (Fog) 2100 hours - Pass.1.3.1.2 ASTM C1549-09 - Standard Test Method for Determination of Solar Reflectance

09 96 00-1

Near Ambient Temperature Using a Portable Solar Reflectometer.1.3.1.3 ASTM D522-93a - Standard Test Methods for Mandrel Bend Test of Attached

Organic Coatings. 1/2 inch () Mandrel: Pass.1.3.1.4 ASTM D968 - Standard Test Methods for Abrasion Resistance of Organic

Coatings by Falling Abrasive. Abrasion Resistance, Falling Sand (Liters): 2,000 with 10 percent erosion. Rating: Excellent.

1.3.1.5 ASTM D6904-03 - Standard Practice for Resistance to Wind-Driven Rain for Exterior Coatings Applied on Masonry. 98 mph () Wind for 24 Hours: Pass.

1.3.1.6 ASTM E84-96a - Standard Test Method for Surface Burning Characteristics of Building Materials: Class A Rating.

1.3.1.7 ASTM E96-95 - Standard Test Methods for Water Vapor Transmission of Materials. Moisture Vapor Transmission: 20 Perms.

1.3.1.8 ASTM G153-04 - Standard Practice for Conducting Accelerated Outdoor Exposure Tests of Coatings. 5,000 hours: Pass.

1.3.2 Material Safety Data Sheets / Environmental Data Sheets: Per manufacturer's MSDS/EDS for specific VOCs (calculated per 40 CFR 59.406). VOCs may vary by base and sheen.

1.3.3 MISSISSIPPI Department of Transportation (MSDOT):1.3.3.1 MSDOT 971-22.2a - Freeze/Thaw ( 100 cycles ) - Pass.

1.3.4 South Coast Air Quality Management District (SCAQMD): Rule 1113 - Architectural Coatings.

1.4 SUBMITTALS

1.4.1 Submit under provisions of Section 01 30 00 - Administrative Requirements.

1.4.2 Product Data:1.4.2.1 Manufacturer's data sheets on each product to be used.1.4.2.2 Preparation instructions and recommendations.1.4.2.3 Storage and handling requirements and recommendations.1.4.2.4 Typical installation methods.

1.4.3 Verification Samples: Two representative units of each type, size, pattern and color.

1.4.4 Shop Drawings: Include details of materials, construction and finish. Include relationship with adjacent construction.

1.5 QUALITY ASSURANCE

1.5.1 Manufacturer Qualifications: Company specializing in manufacturing products specified in this section with a minimum five years documented experience.

1.5.2 Installer Qualifications: Company specializing in performing Work of this section with minimum two years documented experience with projects of similar scope and complexity.

1.5.3 Source Limitations: Provide each type of product from a single manufacturing source to ensure uniformity.

1.5.4 Mock-Up: Construct a mock-up with actual materials in sufficient time for Architect's review and to not delay construction progress. Locate mock-up as acceptable to Architect and provide temporary foundations and support.1.5.4.1 Intent of mock-up is to demonstrate quality of workmanship and visual

appearance.1.5.4.2 If mock-up is not acceptable, rebuild mock-up until satisfactory results are

achieved.1.5.4.3 Retain mock-up during construction as a standard for comparison with

09 96 00-2

completed work.1.5.4.4 Do not alter or remove mock-up until work is completed or removal is authorized.

1.6 PRE-INSTALLATION CONFERENCE

1.6.1 Convene a conference approximately two weeks before scheduled commencement of the Work. Attendees shall include Architect, Contractor and trades involved. Agenda shall include schedule, responsibilities, critical path items and approvals.

1.7 DELIVERY, STORAGE, AND HANDLING

1.7.1 Store and handle in strict compliance with manufacturer's written instructions and recommendations.

1.7.2 Protect from damage due to weather, excessive temperature, and construction operations.

1.8 PROJECT CONDITIONS

1.8.1 Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits.

2 PRODUCTS

2.1 MANUFACTURERS

2.1.1 Acceptable Manufacturer: Textured Coatings of America, Inc., which is located at: Corporate Headquarters & Eastern Manufacturing Facility; 2422 E. 15th St.; Panama City, FL 32405-6348; Toll Free Tel: 800-454-0340; Tel: 850-769-0347; Fax: 850-913-8619; Email:request info ([email protected]); Web:https://www.texcote.com2.1.1.1 Contact: Architectural Resources Manager.

2.1.2 Substitutions: Not permitted.

2.1.3 Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.

2.2 HEAT REFLECTIVE EXTERIOR WALL COATING SYSTEMS

2.2.1 Basis of Design: TEX-COTE COOLWALL Heat Reflective Wall Coating System as manufactured and supplied by Textured Coatings of America, Incorporated.2.2.1.1 Color: ______.2.2.1.2 Color: As determined by the Architect from manufacturer's selection.2.2.1.3 Finish Coat: SUPER-COTE Finish: Heat reflective water based exterior coating.

Meets GS11 Green Seal requirements and ASTM C1549-09 Total Solar Reflectance; Surface wall temperature reduced up to 40 degrees Fahrenheit () depending on color and geographical location as compared to commercial acrylic paint.

2.2.1.3.1 VOC: Less than 50000 ppm (50 grams per liter).2.2.1.3.2 Application: Wet Film Thickness: 7 to 9 mils (0.178 to 0.229 mm). Dry Film

Thickness: 3 to 4 mils (0.076 to 0.102 mm).2.2.1.4 Primer: COOLWALL Classic Primer.2.2.1.5 Primer: COOLWALL Textured Primer.

2.2.1.5.1 Texture: Smooth.2.2.1.5.2 Texture: Sand.2.2.1.5.3 Texture: Fine (medium).2.2.1.5.4 Texture: Coarse.

2.2.1.6 Primer: COOLWALL Textured Primer HD.

09 96 00-3

2.2.1.6.1 Texture: Smooth.2.2.1.6.2 Texture: Sand.2.2.1.6.3 Texture: Fine (medium).2.2.1.6.4 Texture: Coarse.

2.2.1.7 Primer: COOLWALL Re-Cote Primer.

2.3 HEAT REFLECTIVE ROOF AND METAL COATING SYSTEMS

2.3.1 Basis of Design: REFLECT-TEC Kynar System as manufactured and supplied by Textured Coatings of America, Incorporated. Meets ASTM C1549-09 Total Solar Reflectance; Surface wall temperature reduced up to 40 degrees Fahrenheit depending on color and geographical location as compared to commercial acrylic paint.2.3.1.1 Color: ______.2.3.1.2 Color: As determined by the Architect from manufacturer's selection.2.3.1.3 Finish Coat: Product: REFLECT-TEC Kynar Heat Reflective Roof and Wall

Coating. High-performance roof and wall coating system formulated to withstand harsh climate and offers high solar reflectivity and emissivity so that surfaces stay cooler.

2.3.1.3.1 VOC: Less than 50000 ppm (50 grams per liter).2.3.1.3.2 Application: Two coats at a rate of 400 sq. ft per gal (9.817 sq. m per liter)

per coat. Second coat can be applied as soon as first coat is dry to the touch.

2.3.1.4 Primer: Tex-Bond Primer.2.3.1.5 Primer: Metal-Prime Primer.

2.4 HEAT REFLECTIVE CONCRETE AND WOOD DECK COATING SYSTEMS

2.4.1 Basis of Design: Finish Coat TEX-COTE CLEAR-SEAL Protective Clear Top Coat.2.4.1.1 VOC: Less than 50000 ppm (50 grams per liter).2.4.1.2 Application: Second coat applied 4 to 6 hours after first coat. Airless spray is not

recommended.2.4.1.2.1 Horizontal Surfaces: Two coats at a rate of 400 - 600 sq. ft per gal (9.817 -

14.73 sq. m per liter) per coat.

2.4.2 Basis of Design: Finish Coat TEX-COTE COOL-TEC Concrete and Wood Deck Coating. Heat reflective water based exterior coating for aged concrete and wood. Solar reflective, heat and ultraviolet stable pigments. Reflects sun's heat, lowering exterior surface temperatures up 40 degrees F (22.2 degrees C) compared to traditional paints.2.4.2.1 VOC: Less than 50000 ppm (50 grams per liter).2.4.2.2 Application: Second coat applied 4 to 6 hours after first coat. Airless spray is not

recommended.2.4.2.2.1 Horizontal Surfaces: Two coats at a rate of 90 to 110 sq. ft per gal (2.21 to

2.70 sq. m per liter) per coat.2.4.2.2.2 Vertical Surfaces: Two coats at a rate of 400 sq. ft per gal (9.817 sq. m per

liter) per coat. Must be applied in two coats.

2.4.3 Basis of Design: Finish Coat TEX-COTE COOL-TEX CLEAR-GUARD Two-Component Urethane Clear Top Coat.2.4.3.1 VOC: Less than 5000 ppm (5 grams per liter).2.4.3.2 Application: Brush or Roll. Airless spray is not recommended.

2.4.3.2.1 Horizontal Surfaces: One coat at a rate of 350 to 400 sq. ft per gal (8.59 - 9.817 sq. m per liter).

2.4.4 Basis of Design: Base Coat TEX-COTE COOL-TEX Two-Component Epoxy Concrete Floor and Deck Coating.2.4.4.1 VOC: Less than 10000 ppm (10 grams per liter).2.4.4.2 Application: Brush or Roll. Airless spray is not recommended.

09 96 00-4

2.4.4.2.1 Horizontal Surfaces: Two coats at a rate of 100 sq. ft per gal (2.45 sq. m per liter) per coat.

2.5 ARCHITECTURAL TEXTURED AND SMOOTH HIGH BUILD COATINGS

2.5.1 Basis of Design: Finish Coat XL-70 "W" Textured Coating. A water-based high-build, advanced epoxy-acrylate resin system specially formulated to provide a weatherproof coating over cured or uncured concrete masonry surfaces.2.5.1.1 VOC: Less than 100 grams per liter.2.5.1.2 Application: Wet Film Thickness: 35.5 mils (0.902 mm), Dry Film Thickness: 16

mils.2.5.1.3 Texture: Smooth.2.5.1.4 Texture: Sand.2.5.1.5 Texture: Fine (medium).2.5.1.6 Texture: Coarse.2.5.1.7 Color: ______.2.5.1.8 Color: As determined by the Architect from manufacturer's selection.

2.5.2 Basis of Design: Finish Coat XL-70 Textured Coating (Solvent). A high-build, plasticized, vinyl toluene acrylic resin system specially formulated to provide a weatherproof coating over cured or green concrete masonry surfaces.2.5.2.1 VOC: 350000 ppm (350 grams per liter).2.5.2.2 Application: Coverage rates vary due to surface porosity, texture and application

method. Wet Film Thickness: 35.5 mils (0.902 mm), Dry Film Thickness: 16 mils.

2.5.2.2.1 Roller Applied Finishes: Smooth, sand, or fine textures.2.5.2.2.2 Spray Applied Finishes: Smooth, sand, fine, or coarse textures.

2.5.2.2.2.1 Texture: Smooth.2.5.2.2.2.2 Texture: Sand.2.5.2.2.2.3 Texture: Fine (medium).2.5.2.2.2.4 Texture: Coarse.

2.5.2.3 Color: ______.2.5.2.4 Color: As determined by the Architect from manufacturer's selection.

2.5.3 Basis of Design: Finish Coat XL-70 "W" Smooth Airless Coating. A water-based high-build, advanced epoxy-acrylate resin system specially formulated to provide a weatherproof coating over cured or uncured concrete masonry surfaces.2.5.3.1 VOC: Less than 100000 ppm (100 grams per liter).2.5.3.2 Application: Coverage rates vary due to surface porosity, texture and application

method.2.5.3.2.1 Roller Applied Finishes: Smooth.2.5.3.2.2 Spray Applied: Smooth airless.


2.5.4 Basis of Design: Finish Coat XL-70 Smooth Airless Coating (Solvent). Smooth Airless Concrete / Masonry Protective Coating is a high-build, plasticized, vinyl toluene acrylic resin system specially formulated to provide a weatherproof coating over cured or uncured concrete masonry surfaces.2.5.4.1 VOC: 400000 ppm (400 grams per liter).2.5.4.2 Application: Approximately 80 to 100 sq. ft per gal (1.96 to 2.45 sq. m per liter)

over properly prepared dense substrates such as tilt-up, pre-cast or poured concrete.

2.5.4.3 Apply two coats at 80 to 100 sq. ft per gallon per coat on porous substrates.2.5.4.4 Color: ______.2.5.4.5 Color: As determined by the Architect from manufacturer's selection.

09 96 00-5

2.5.5 Basis of Design: Finish Coat TEX-COTE TC600 Textured Coating. A high build, 100 percent acrylic terpolymer, water based coating with elastomeric properties, featuring rapid drying and adhesion.2.5.5.1 VOC: Less than 100000 ppm (100 grams per liter).2.5.5.2 Application: 45 sq. ft per gal (1.10 sq. m per liter), plus or minus 5 sq. ft (0.465

sq. m), depending upon porosity and texture desired.2.5.5.3 Texture: Smooth.2.5.5.4 Texture: Sand.2.5.5.5 Texture: Fine (medium).2.5.5.6 Texture: Coarse.2.5.5.7 Color: ______.2.5.5.8 Color: As determined by the Architect from manufacturer's selection.

2.5.6 Basis of Design: Finish Coat TEX-COTE TC400 Textured Coating. A high-build, efflorescence blocking, water based coating with elastomeric properties featuring rapid drying and superior adhesion. This styrene acrylic coating is recommended for use over concrete, cement plaster, block, brick, metal and other manufacturer approved surfaces.2.5.6.1 VOC: Less than 100000 ppm (100 grams per liter).2.5.6.2 Application: 45 sq. ft per gal (1.10 sq. m per liter), plus or minus 5 sq. ft (0.465

sq. m), depending upon porosity and texture desired.2.5.6.3 Texture: Smooth.2.5.6.4 Texture: Sand.2.5.6.5 Texture: Fine (medium).2.5.6.6 Texture: Coarse.2.5.6.7 Color: ______.2.5.6.8 Color: As determined by the Architect from manufacturer's selection.

2.5.7 Basis of Design: Finish Coat TEX-COTE TC400 Smooth Airless Coating. A high-build, efflorescence blocking, water based coating with elastomeric properties featuring rapid drying and superior adhesion. This styrene acrylic coating is recommended for use over concrete, cement plaster, block, brick, metal and other manufacturer approved surfaces.2.5.7.1 VOC: Less than 100000 ppm (100 grams per liter).2.5.7.2 Application: A rate of 80 to 100 sq. ft per gal (1.96 to 2.45 sq. m per liter). A

minimum of 8 to 10 mils (0.203 to 0.254 mm) dry film is required for smooth coating.


2.5.8 Basis of Design: Finish Coat TEX-COTE TC300 Textured Coating. A high-build, latex/acrylic copolymer coating formulated for use on concrete / masonry surfaces.2.5.8.1 VOC: Less than 100000 ppm (100 grams per liter).2.5.8.2 Application: 60 to 80 sq. ft per gal (1.47 - 1.96 sq. m per liter) depending upon

porosity and texture desired.2.5.8.3 Texture: Smooth.2.5.8.4 Texture: Sand.2.5.8.5 Texture: Fine (medium).2.5.8.6 Texture: Coarse.2.5.8.7 Color: ______.2.5.8.8 Color: As determined by the Architect from manufacturer's selection.

2.5.9 Basis of Design: Finish Coat TEX-COTE TC300 Smooth Airless Coating. A high-build, latex/acrylic copolymer coating formulated for use on concrete / masonry surfaces.2.5.9.1 VOC: Less than 100000 ppm (100 grams per liter).2.5.9.2 Application: A rate of 80 to 100 sq. ft per gal (1.96 to 2.45 sq. m per liter). A

minimum of 8 to 10 mils (0.203 to 0.254 mm) dry film is required for smooth coating.

09 96 00-6


2.5.10 Basis of Design: Finish Coat TEX-COTE Tex-Gard Textured Coating. A high build latex (water base) coating which features good adhesion, rapid dry and flexibility. This coating may be used over concrete, cement plaster, block, cement and fiber board, metal and other approved surfaces.2.5.10.1 VOC: Less than 100000 ppm (100 grams per liter).2.5.10.2 Application: Apply coating at 50 to 75 sq. ft per gal ( 1.23 to 1.84 square

meter/liter ) depending on the porosity and finished texture desired.2.5.10.3 Texture: Smooth.2.5.10.4 Texture: Sand.2.5.10.5 Texture: Fine (medium).2.5.10.6 Texture: Coarse.2.5.10.7 Color: ______.2.5.10.8 Color: As determined by the Architect from manufacturer's selection.

2.5.11 Basis of Design: Finish Coat TEX-COTE S-T-R-E-T-C-H Elastomeric Coating. A high performance terpolymer elastomeric coating with a 100 percent acrylic latex base elastomeric resin providing up to 400 percent elongation.2.5.11.1 VOC: Less than 100000 ppm (100 grams per liter).2.5.11.2 Application: A rate of 80 to 100 sq. ft per gal (1.96 to 2.45 sq. m per liter).

Coverage rates may vary due to wall surface textures and porosity. A minimum of 9 -10 mils (22 mm to 25 mm) dry film thickness is required.


2.5.12 Basis of Design: Finish Coat TEX-COTE Stone-Tex System. A 100 percent acrylic terpolymer. Recommended over selected TEX-COTE exterior textured coating base coats to provide a variety of simulated appearances such as granite, marble, sandstone or stone. Finish coat available in smooth or fine texture.2.5.12.1 VOC: Less than or equal to 100000 ppm (100 grams per liter).2.5.12.2 Application: Base coat is applied at 40 to 55 sq. ft per gal (0.98 to 1.35 sq. m per

liter). Splatter coats will vary depending upon finish and texture. Smooth splatters will range between 80 to 125 sq. ft per gal (1.96 to 3.07 sq. m per liter). Fine texture splatters range from 60 to 85 sq. ft per gal (1.47 to 2.09 sq. m per liter).

2.5.12.3 Texture: Smooth.2.5.12.4 Texture: Sand.2.5.12.5 Texture: Fine (medium).2.5.12.6 Texture: Coarse.2.5.12.7 Color: ______.2.5.12.8 Color: As determined by the Architect from manufacturer's selection.

2.5.13 Basis of Design: Finish Coat TEX-COTE Elastomeric Roof Coating. A high solids latex acrylic coating formulated to impart superior resistance to ponding water conditions. It has excellent adhesion to fresh urethane foam, galvanized metal, aluminum, concrete, cementitious and clay tile.2.5.13.1 VOC: Less than or equal to 50000 ppm (50 grams per liter).2.5.13.2 Application: Elastomeric Roof Coating I; Base Coat (Gray): Apply at a rate of 1 to

1-1/2 gallons per 100 square feet (0.62 liters/square meter) to produce a dry film thickness of 10 to 13 mils (0.254 to 0.33 mm).

2.5.13.3 Application: Elastomeric Roof Coating II; Top Coat (Bright Reflective White): Apply at a rate of 1 to 1-1/2 gallons per 100 square feet (0.62 liters/square meter) to produce a minimum dry film thickness of 13.8 mils (0.35 mm).

2.6 ARCHITECTURAL TEXTURED AND SMOOTH COATINGS

09 96 00-7

2.6.1 Basis of Design: Finish Coat TEX-COTE TRIM-COTE. A 100 percent acrylic resin exterior finish to be applied over Primer 27 W, and approved substrates. Weather, salt spray, moisture and mildew resistant.2.6.1.1 VOC: Less than or equal to 50000 ppm (50 grams per liter).2.6.1.2 Application: 175 to 225 sq. ft per gal (0.98 to 1.35 sq. m per liter) depending on

surface porosity and texture. Application: Spray, roll or brush.2.6.1.3 Finish: Satin2.6.1.4 Finish: Semi-gloss.2.6.1.5 Color: ______.2.6.1.6 Color: As determined by the Architect from manufacturer's selection.

2.6.2 Basis of Design: Finish Coat TEX-COTE COLOR-TEX. Textured interior/exterior seamless water-based urethane acrylic latex wall finish. For use on a wide range of wall surfaces, such as drywall, concrete, concrete block, brick, stucco, wood, glass, plaster, metal, and plastic. Fungus and mildew resistant highly breathable, and fire resistant.2.6.2.1 VOC: Less than 300000 ppm (300 grams per liter).2.6.2.2 Application: 175 to 250 sq. ft per gal (4.29 to 6.14 sq. m per liter) depending on

surface porosity and texture. Base Coat: spray or rolled. Finish Cote: Sprayed.2.6.2.3 Color: ______.2.6.2.4 Color: As determined by the Architect from manufacturer's selection.

2.6.3 Basis of Design: Finish Coat TEX-COTE TEX-TURA. Textured interior/exterior seamless water-based latex wall finish. For use on a wide range of wall surfaces, such as drywall, concrete, concrete block, brick, stucco, wood, glass, plaster, metal, and plastic. Fungus and mildew resistant highly breathable, and fire resistant.2.6.3.1 VOC: Less than 50000 ppm (50 grams per liter).2.6.3.2 Application: 175 to 250 sq. ft per gal (4.29 to 6.14 sq. m per liter) depending on

surface porosity and texture. Base Coat: spray or rolled. Finish Cote: Sprayed.2.6.3.3 Color: ______.2.6.3.4 Color: As determined by the Architect from manufacturer's selection.

2.6.4 Basis of Design: Finish Coat TEX-COTE ERASER-COTE. Very low VOC, ultra-low odor, two-part water-based polyurethane white or clear coating that creates a high performance seamless dry-erase writing surface for use with industry standard dry-erase markers and erasers. Roller apply only using brush to cut-in.2.6.4.1 VOC: Less than 50000 ppm (50 grams per liter).2.6.4.2 Application: depending on surface porosity and texture.

2.6.4.2.1 White: 200 to 240 sq. ft per gal (4.91 to 5.89 sq. m per liter).2.6.4.2.2 Clear: 240 to 320 sq. ft per gal (5.89 to 7.85 sq. m per liter).

2.6.5 Basis of Design: Finish Coat TEX-COTE COOL-TEX Concrete Floor and Deck Coating. 2 component, water-based epoxy coating system that provides superior performance and wear characteristics for garage floors, patios, and walkways.2.6.5.1 VOC: Less than 10000 ppm (10 grams per liter).2.6.5.2 Application: Two coats at 90 to 110 sq. ft per gal (2.21 to 2.7 sq. m per liter) per

coat.2.6.5.3 Color: ______.2.6.5.4 Color: As determined by the Architect from manufacturer's selection.

2.7 TOP COATS

2.7.1 Basis of Design: Finish Coat TEX-COTE CLEAR-GUARD Two Component Urethane. An advanced, very low VOC water-based polyurethane coating system that provides superior performance and wear characteristics for previously coated surfaces that are prone to dirt pickup, chemical exposure, staining, or other high-traffic areas such as hand rails and doors.2.7.1.1 VOC: Less than or equal to 5000 ppm (5 grams per liter).2.7.1.2 Application: 350 to 400 sq. ft per gal (8.59 to 9.82 sq. m per liter) per coat.

09 96 00-8

(allow cure between coats) using a 3/8 in (9.5 mm) nap high quality roller. For best performance, apply two coats. Additional coats increase gloss and deepen the final color.

2.7.2 Basis of Design: Finish Coat TEX-COTE CLEAR-SEAL One Component Acrylic. Water-based, 100 percent acrylic, penetrating sealer producing a clear satin finish surface film. Non-yellowing, acrylic resins form a durable finish providing water-repellency, dirt pick-up resistance and weather protection.2.7.2.1 VOC :Less than 50000 ppm (50 grams per liter).2.7.2.2 Application: 400 to 600 sq. ft per gal (9.82 to 14.73 sq. m per liter). Multiple coats

are possible to achieve the desired surface effects.

2.7.3 Basis of Design: Finish Coat TEX-COTE COLOR-COTE. Compatible with and have excellent adhesion to the different types of textured coatings. Salt spray, moisture, and mildew resistant. Can be used for color changes, banding, to revive older projects, or by itself with an appropriate priming system over manufacturer approved substrates.2.7.3.1 VOC: Less than 100000 ppm (100 grams per liter).2.7.3.2 Application: 200 to 250 sq. ft per gal (4.91 to 6.14 sq. m per liter) depending on

surface porosity and texture.2.7.3.3 Color: ______.2.7.3.4 Color: As determined by the Architect from manufacturer's selection.

2.7.4 Basis of Design: Finish Coat TEX-COTE D.F. COLOR-COTE DEAD FLAT. 100 percent acrylic latex exterior finish to be applied over approved textured primers, and water or oil based textured coatings. Weather, moisture and mildew resistant.2.7.4.1 VOC: Less than 100000 ppm (100 grams per liter).2.7.4.2 Application: 175 to 250 sq. ft per gal (4.25 to 6.1 sq. m per liter) depending on

surface porosity and texture.2.7.4.3 Color: ______.2.7.4.4 Color: As determined by the Architect from manufacturer's selection.

2.7.5 Basis of Design: Finish Coat TEX-COTE COOL-TEX CLEAR-GARD. 2 component, water-based, poly-urethane coating system providing superior performance and wear characteristics for COOL-TEX coated floors, driveways, patios, and walkways. Tough medium to high gloss finish. Stain, scratch, and UV resistant.2.7.5.1 VOC: Less than 5000 ppm (5 grams per liter).2.7.5.2 Application: Two coats at 350 to 400 sq. ft per gal (9.82 to 14.73 sq. m per liter)

per coat. Applying more than two coats is possible to achieve the desired surface effects.

2.8 EIFS FINISHES

2.8.1 Basis of Design: TEX-COTE EIFS Finishes as manufactured and supplied by Textured Coatings of America, Incorporated2.8.1.1 Finish Coat: TEX-COTE EIFS Textured Spray or Trowel Finish System as

manufactured and supplied by Textured Coatings of America, Incorporated. A water-based high-build, advanced acrylic resin system with heat and solar reflective properties. Used to protect and enhance EIFS, stucco, vertical metal surfaces, and other approved surfaces where a thick concrete appearance is desired. Dries quickly to a hard, durable finish. Ideal for masking surface imperfections.

2.8.1.1.1 VOC: Less than 50000 ppm (50 grams per liter).2.8.1.1.2 Application, Spray: Coverage rate of 50 to 70 sq. ft per gal (1.23 to 1.72

sq. m per liter) depending on the texture chosen.2.8.1.1.3 Application, Trowel: Coverage rate of 40 to 50 sq. ft per gal (0.98 to 1.23

sq. m per liter) depending on texture and technique.2.8.1.1.4 Texture: Sand.

09 96 00-9

2.8.1.1.5 Texture: Fine (medium).2.8.1.1.6 Texture: Coarse.2.8.1.1.7 Color: ______.2.8.1.1.8 Color: As determined by the Architect from manufacturer's selection.

2.8.1.2 Primer: TEX-COTE EIFS Primer

2.9 PENETRANT SEALERS - WATER REPELLENTS AND STAINS

2.9.1 Basis of Design: Finish Coat TEX-COTE RAINSTOPPER 110 - 10 Percent Silane Sealer. Commercial chemical treatment which causes concrete, masonry, limestone or mineral substrates to become repellent to salt and water.2.9.1.1 VOC: Less than 400000 ppm (400 grams per liter).2.9.1.2 Application: Coverage rate will vary depending upon porosity of substrate.

2.9.1.2.1 Estimated Coverage:2.9.1.2.1.1 Limestone Aggregates, Brick/Masonry, Sandstone, Stucco, Split

Faced Block: 75 to 100 sq. ft per gal (1.84 to 2.45 sq. m per liter).2.9.1.2.1.2 Gravel, Sand, Granite, Precast Concrete, Architectural Concrete,

Flagstone, Synthetic Stone: 100 to 125 sq. ft per gal (2.45 to 3.07 sq. m per liter).


2.9.2 Basis of Design: Finish Coat TEX-COTE RAINSTOPPER 120 - 20 Percent Silane Sealer. Commercial chemical treatment which causes concrete, masonry, limestone or mineral substrates to become repellent to salt and water.2.9.2.1 VOC: Less than or equal to 400000 ppm (400 grams per liter).2.9.2.2 Application: Coverage rate will vary depending upon porosity of substrate.





2.9.3 Basis of Design: Finish Coat TEX-COTE RAINSTOPPER 140 - 40 Percent Silane Sealer. Residential chemical treatment which causes concrete, masonry, limestone or mineral substrates to become repellent to salt and water.2.9.3.1 VOC: Less than or equal to 400000 ppm (400 grams per liter).2.9.3.2 Application: Coverage rate will vary depending upon porosity of substrate.





2.9.4 Basis of Design: Finish Coat TEX-COTE RAINSTOPPER 120W - 20 Percent Silane Sealer. Single component ready-to-use water-based silane clear penetrating sealers making concrete, masonry, and other mineral substrates repellent to water and dissolved salts.2.9.4.1 VOC: Less than or equal to 350000 ppm (350 grams per liter).2.9.4.2 Application: 100 to 175 sq. ft per gal (2.45 to 4.29 sq. m per liter).2.9.4.3 Color: ______.2.9.4.4 Color: As determined by the Architect from manufacturer's selection.

09 96 00-10

2.9.5 Basis of Design: Finish Coat TEX-COTE RAINSTOPPER 140W - 40 Percent Silane Sealer. Single component ready-to-use water-based silane clear penetrating sealers making concrete, masonry, and other mineral substrates repellent to water and dissolved salts.2.9.5.1 VOC: Less than 350000 ppm (350 grams per liter).2.9.5.2 Application: 100 to 200 sq. ft per gal (2.45 to 4.91 sq. m per liter).2.9.5.3 Color: ______.2.9.5.4 Color: As determined by the Architect from manufacturer's selection.

2.9.6 Basis of Design: Finish Coat TEX-COTE RAINSTOPPER 1750W CLEAR Sealer. a micro-emulsifiable concentrate based on silanes and alkoxysilanes producing a micro-emulsion when mixed with water. This diluted form will impart water repellency to absorbent mineral surfaces.2.9.6.1 VOC: Less than 350000 ppm (350 grams per liter).2.9.6.2 Application: Rate will vary dependent upon porosity.

2.9.6.2.1 Brick, Masonry, Stone, Limestone Aggregates, Gravel, Sand, Flagstone, and Stucco:

2.9.6.2.1.1 Diluted: 75 to 100 sq. ft per gal (1.84 to 2.45 sq. m per liter)2.9.6.2.1.2 Concentrate: 375 to 500 sq. ft per gal (9.20 to 12.27 sq. m per

liter)2.9.6.2.2 Precast Concrete, Architectural Concrete, and Synthetic Stone:

2.9.6.2.2.1 Diluted: 100 to 125 sq. ft per gal (2.45 to 3.07 sq. m per liter).2.9.6.2.2.2 Concentrate: 500 to 625 sq. ft per gal (12.27 to 15.34 sq. m per

liter).2.9.6.2.3 For priming dilutions, coverage per gallon of concentrate is approximately

double sealing operations.2.9.6.3 Color: ______.2.9.6.4 Color: As determined by the Architect from manufacturer's selection.

2.9.7 Basis of Design: Finish Coat TEX-COTE RAINSTOPPER 2000 CLEAR Sealer. A combination of a silicone emulsion with a reactive silane producing a penetrating concrete and masonry sealer and water repellant.2.9.7.1 VOC: Less than 120000 ppm (120 grams per liter).2.9.7.2 Application: Rate will vary dependent upon porosity.

2.9.7.2.1 Brick, Masonry, Stone, Limestone Aggregates, Gravel, Sand, Flagstone, and Stucco:

2.9.7.2.1.1 Diluted: 75 to 100 sq. ft per gal (1.84 to 2.45 sq. m per liter)2.9.7.2.2 Precast Concrete, Architectural Concrete, and Synthetic Stone:

2.9.7.2.2.1 Diluted: 100 to 125 sq. ft per gal (2.45 to 3.07 sq. m per liter).2.9.7.2.3 For priming, coverage per gallon of concentrate is approximately double

sealing operations.2.9.7.3 Color: ______.2.9.7.4 Color: As determined by the Architect from manufacturer's selection.

2.9.8 Basis of Design: Finish Coat TEX-COTE RAINSTOPPER ULTRA SILICONE ACRYLIC CONCRETE STAIN (Opaque/Satin). Water based modified acrylic resin, providing an opaque, long lasting, color toning deep satin finish to concrete and masonry surfaces, water repellency and chloride ion intrusion while allowing moisture and vapor transmission. Specially formulated to provide resistance to alkali, mildew, calcium chloride, and ultraviolet degradation.2.9.8.1 VOC: Less than or equal to 100000 ppm (100 grams per liter).2.9.8.2 Application: 100 to 200 sq. ft per gal (2.45 to 4.91 sq. m per liter) depending of

substrate porosity.2.9.8.3 Color: ______.2.9.8.4 Color: As determined by the Architect from manufacturer's selection.

2.10 ANTI GRAFFITI COATINGS SYSTEMS

09 96 00-11

2.10.1 Basis of Design: Finish Coat TEX-COTE GRAFFITI GARD IV GLOSS. Non-sacrificial, two-component, water based high performance clear aliphatic urethane coating that resists graffiti from a variety of materials including spray paints and marking pens.2.10.1.1 VOC: Less than 50000 ppm (50 grams per liter).2.10.1.2 Application: 250 to 350 sq. ft per gal (6.14 to 8.59 sq. m per liter). Textured or

absorbent surfaces will require additional material.

2.10.2 Basis of Design: Finish Coat TEX-COTE GRAFFITI GARD IV LOW LUSTER OR PIGMENTED. Non-sacrificial, two component, water-based, high performance clear or pigmented aliphatic urethane coating. Resists graffiti from a variety of materials including spray paints and marking pens.2.10.2.1 VOC: Less than 50000 ppm (50 grams per liter).2.10.2.2 Application: 250 to 350 sq. ft per gal (6.14 to 8.59 sq. m per liter). Textured or


2.10.3 Basis of Design: Finish Coat TEX-COTE GRAFFITI GARD S. Non-sacrificial, one-component, high performance poly-siloxane hybrid coating. Resists graffiti from a variety of materials including spray paints and marking pens.2.10.3.1 VOC: Less than 250000 ppm (250 grams per liter).2.10.3.2 Application: 75 to 125 sq. ft per gal (1.84 to 3.07 sq. m per liter). Textured or


2.10.4 Basis of Design: Finish Coat TEX-COTE SACRIFICIAL GRAFFITI GARD. a specially formulated and blended water based resin for optimum performance as a protective sacrificial system over new or previously painted substrates.2.10.4.1 VOC: Less than 50000 ppm (50 grams per liter).2.10.4.2 Application: 150 to 250 sq. ft per gal (3.68 to 6.14 sq. m per liter) depending on

porosity. Coating must be a continuous pinhole free film.

2.10.5 Basis of Design: Finish Coat TEX-COTE TY-COTE CLEAR. Aliphatic polyurethane dispersion, acts as a " F ill Coat " for the substrate and maintains clarity of the substrate. Used for murals, natural stones, architectural block or brick, and other decorative surfaces that need protection from graffiti.2.10.5.1 VOC: Less than 200000 ppm (200 grams per liter).2.10.5.2 Application: 200 sq. ft per gal (4.91 sq. m per liter) coverage rates may vary due

to wall surface texture and porosity. Highly porous surfaces may require additional coats.

2.10.6 Basis of Design: Finish Coat TEX-COTE TY-COTE PIGMENTED. Protects old paint from solvents in the can match customer's specified color. Must create a continuous pinhole free film.2.10.6.1 VOC: Less than 100000 ppm (100 grams per liter).2.10.6.2 Application: 200 sq. ft per gal (4.91 sq. m per liter) coverage rates may vary due

to wall surface texture and porosity. Highly porous surfaces may require additional coats.

2.10.7 Basis of Design: Cleaner TEX-COTE GRAFFITI GARD IV BIODEGRADABLE CLEANER. Proprietary, state-of-the-art, environmentally friendly, used to clean graffiti off surfaces that have been protected with GRAFFITI GARD IV GLOSS or LOW LUSTER, GRAFFITI GARD IV LOW LUSTER. Non-regulated, nearly 0 VOC cleaner. Effectively removes graffiti safely without pungent odors or fumes leaving graffiti guard film intact to continue protecting against graffiti.2.10.7.1 VOC: Less than 1000 ppm (1 gram per liter).2.10.7.2 Application: One quart of cleaner will usually clean approximately 40 to 50

square feet (3.72 to 4.64 sq. m) of affected area.

2.11 CARWASH COATING SYSTEMS

09 96 00-12

2.11.1 Basis of Design: Finish Coat TEX-COTE WASH-GUARD COOLWALL SUPER-COTE System. Waterborne, smooth finish high-performance, high-build, concrete coating system withstanding harsh conditions of commercial car-washes. Protection from water, soaps, acids, alkali, oil, grease, and salt spray.2.11.1.1 VOC: Less than 50000 ppm (50 grams per liter).2.11.1.2 Application: one coat at 175 to 225 sq. ft per gal (4.29 to 5.5 sq. m per liter) or 7

to 9 mils wet.2.11.1.3 Color: ______.2.11.1.4 Color: As determined by the Architect from manufacturer's selection.

2.11.2 Basis of Design: Finish Coat TEX-COTE WASH-GUARD CLEAR GUARD System. Very low VOC water-based polyurethane coating system providing superior performance and wear characteristics for surfaces previously coated with compatible TEX-COTE products. Provides a medium-to-high gloss surface finish to a coated surface. Protects the coated surface, increasing the life of the coating. Designed to resist chipping, flaking and peeling.2.11.2.1 VOC: Less than 5000 ppm (5 grams per liter).2.11.2.2 Application: Applied as a two coat system at a rate of 350 to 400 sq. ft per gal

(8.59 to 9.82 sq. m per liter) per coat (allowing cure between coats) using a 1/2 in (9.5 mm) nap high quality roller. Additional coats will increase the gloss and deepen the final color.


2.12 PRIMERS

2.12.1 Basis of Design: Primer Coat TEX-COTE COOLWALL Classic Primer as manufactured and supplied by Textured Coatings of America, Incorporated. A multifunctional low VOC acrylic copolymer pigmented latex system.2.12.1.1 VOC: Less than 100000 ppm (100 grams per liter).2.12.1.2 Application: Wet Film Thickness: 16 to 20 mils (0.406 to 0.508 mm), Dry Film

Thickness: 8 to 10 mils (0.203 to 0.254 mm).

2.12.2 Basis of Design: Primer Coat TEX-COTE COOLWALL Textured Primer as manufactured and supplied by Textured Coatings of America, Incorporated. A multi-functional, low VOC acrylic latex system.2.12.2.1 VOC: Less than 100000 ppm (100 grams per liter).2.12.2.2 Application: Apply at a rate of 0 to 80 sq. ft per gal (1.47 to 1.96 sq. m per liter)

depending upon surface porosity and desired texture.2.12.2.3 Texture: Smooth.2.12.2.4 Texture: Sand.2.12.2.5 Texture: Fine (medium).2.12.2.6 Texture: Coarse.

2.12.3 Basis of Design: Primer Coat TEX-COTE COOLWALL Textured Primer HD as manufactured and supplied by Textured Coatings of America, Incorporated. A multi-functional, low VOC acrylic latex system.2.12.3.1 VOC: Less than 100000 ppm (100 grams per liter).2.12.3.2 Application: Apply at a rate of 50 to 60 sq. ft per gal (1.27 to 1.47 sq. m per liter)

depending upon surface porosity and desired texture.2.12.3.3 Texture: Smooth.2.12.3.4 Texture: Sand.2.12.3.5 Texture: Fine (medium).2.12.3.6 Texture: Coarse.

2.12.4 Basis of Design: Primer Coat TEX-COTE COOLWALL Re-Cote Primer as manufactured and supplied by Textured Coatings of America, Incorporated. A low VOC 100 percent acrylic primer.

09 96 00-13

2.12.4.1 VOC: Less than 100000 ppm (100 grams per liter) minus water.2.12.4.2 Application: Brush or roller or conventional airless to substrate at recommended

coverage rate. 250 to 300 sq. ft per gal (6.14 to 7.36 sq. m per liter), depending upon surface porosity and type of finish.

2.12.5 Basis of Design: Primer Coat TEX-COTE Metal-Prime Primer as manufactured and supplied by Textured Coatings of America, Incorporated. Water based, ready-to-use primer formulated for corrosion protection and adhesion to metal surfaces.2.12.5.1 VOC: Less than 100000 ppm (100 grams per liter).2.12.5.2 Application: Apply at a coverage rate of 300 to 400 sq. ft per gal (7.36 to 9.81 sq.

m per liter).

2.12.6 Basis of Design: Primer Coat TEX-COTE XL 70 "W" (Water Based) Primer as manufactured and supplied by Textured Coatings of America, Incorporated. Complies with California Air Resource Board (C.A.R.B.) Rule 1113 and also United States EPA regulations. A water -based, epoxy acrylic hybrid for use under water based topcoats.2.12.6.1 VOC: Less than 100000 ppm (100 grams per liter).2.12.6.2 Application: Apply at a coverage rate of 250 to 350 sq. ft per gal (4.91 to 8.59 sq.

m per liter).

2.12.7 Basis of Design: Primer Coat TEX-COTE XL 70 (Solvent) Primer as manufactured and supplied by Textured Coatings of America, Incorporated. A solvent based vinyl toluene acrylic (VTAC) material. Use where damp, uncured cementitious surfaces are common, or where excessive amounts of alkali are present in the substrate.2.12.7.1 VOC: Less than 3050000 ppm (3050 grams per liter).2.12.7.2 Application: Apply to clean, dry surface at a rate of 175 to 300 sq. ft per gal

(4.29 to 7.36 sq. m per liter) depending upon porosity. After spray application, brush or back roll, using fully loaded roller or brush, to fill block.

2.12.8 Basis of Design: Primer Coat TEX-COTE Primer 27 "W" (Water Based) Primer as manufactured and supplied by Textured Coatings of America, Incorporated. Complies with California Air Resource Board (C.A.R.B.) Rule 1113 and also United States EPA regulations. This unique primer is an advanced water based acrylic system for use under water based interior or exterior topcoats.2.12.8.1 VOC: Less than 100000 ppm (100 grams per liter).2.12.8.2 Application: Apply to clean, dry surface at a rate of 300 to 400 sq. ft per gal (7.36

to 9.82 sq. m per liter) depending upon porosity. Apply with brush, roller or conventional airless to substrate at recommended coverage rate.

2.12.9 Basis of Design: Primer Coat TEX-COTE TEX-BOND Primer as manufactured and supplied by Textured Coatings of America, Incorporated. A water-based, ready-to-use primer specifically formulated to act as a bonding coat over difficult to adhere surfaces.2.12.9.1 VOC: Less than 100000 ppm (100 grams per liter).2.12.9.2 Application: Apply to clean, dry surface at a rate of 300 to 400 sq. ft per gal (7.36

to 9.82 sq. m per liter).

2.12.10 Basis of Design: Primer Coat TEX-COTE Concrete and Masonry Primer as manufactured and supplied by Textured Coatings of America, Incorporated. a low VOC 100 percent acrylic primer.2.12.10.1 VOC: Less than 100000 ppm (100 grams per liter).2.12.10.2 Application: Apply to clean, dry surface at a rate of 250 to 300 sq. ft per gal (6.1

to 7.36 sq. m per liter), depending upon surface porosity and type of finish.

2.12.11 Basis of Design: Primer Coat TEX-COTE TEX-TITE Primer as manufactured and supplied by Textured Coatings of America, Incorporated. a low VOC 100 percent acrylic primer.2.12.11.1 VOC: Less than 150000 ppm (150 grams per liter).

09 96 00-14

2.12.11.2 Application: Apply to clean, dry surface at a rate of 200 to 250 sq. ft per gal (4.9 to 6.1 sq. m per liter), depending upon surface porosity and type of finish.

2.12.12 Basis of Design: Primer Coat TEX-COTE EIFS Primer as manufactured and supplied by Textured Coatings of America, Incorporated. a low VOC 100 percent acrylic primer. Excellent adhesion to chalky and previously painted surfaces.2.12.12.1 VOC: Less than 100000 ppm (100 grams per liter).2.12.12.2 Application: Apply to clean, dry surface at a rate of 250 to 300 sq. ft per gal (6.14

to 7.36 sq. m per liter), depending upon surface porosity and type of finish.

2.12.13 Basis of Design: Primer Coat TEX-COTE WASH-GUARD Classic Primer as manufactured and supplied by Textured Coatings of America, Incorporated. Multifunctional low VOC acrylic copolymer pigmented latex system. Rheology modifiers provide non-sag, leveling and film build when freshly applied. For surfaces where excessive amounts of alkali are present in the substrate.2.12.13.1 VOC: Less than 100000 ppm (100 grams per liter).2.12.13.2 Application; New Commercial Applications: 80 to 100 sq. ft per gal (1.96 to 2.45

sq. m per liter) depending upon surface porosity and texture.2.12.13.3 Application; Commercial Repaint Applications: 125 to 150 sq. ft per gal (3.07 to

3.68 sq. m per liter) depending upon surface porosity and texture.

2.13 BLOCKS FILLERS AND PATCHING COMPOUNDS

2.13.1 Basis of Design: TEX-COTE Latex Block Filler as manufactured and supplied by Textured Coatings of America, Incorporated. A pigmented, styrene-acrylic base resin system formulated to provide filling and damp-proofing properties to masonry block systems. Meets most parameters of Federal Specification 1098D.2.13.1.1 VOC: Less than 100000 ppm (100 grams per liter).2.13.1.2 Application: Apply at 50 to 80 sq. ft per gal (1.23 to 1.96 sq. m per liter)

depending on surface porosity and texture. Smooth as necessary to provide a tight seal against water intrusion into block.

2.13.2 Basis of Design: TEX-COTE Flex-Patch Patching Compound as manufactured and supplied by Textured Coatings of America, Incorporated. A water based, ready to use patching compound available in both knife (texture) and butter (smooth ) grades. It is applied to a maximum of 1/32 inch.2.13.2.1 VOC: Less than 100000 ppm (100 grams per liter).2.13.2.2 Application: Apply at a rate of 25 sq. ft per gal (0.61 sq. m per liter). Application

rate is dependent upon the surface porosity and patching irregularity.

2.13.3 Basis of Design: TEX-COTE Skim Cote as manufactured and supplied by Textured Coatings of America, Incorporated. A trowel grade water-based acrylic skim coat, used for filling block lines as well as a skim coat or block filler for a masonry wall.2.13.3.1 VOC: Less than 100000 ppm (100 grams per liter).2.13.3.2 Application: 12 to 25 sq. ft per gal (0.3 to 0.61 sq. m per liter), depending upon

surface porosity and type of finish, and wall configuration.

3 EXECUTION

3.1 EXAMINATION

3.1.1 Do not begin installation until substrates have been properly constructed and prepared.

3.1.2 If substrate preparation is the responsibility of another installer, notify Architect in writing of unsatisfactory preparation before proceeding.

3.2 PREPARATION

09 96 00-15

3.2.1 Clean surfaces thoroughly prior to installation.

3.2.2 Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.

3.3 INSTALLATION

3.3.1 Install in accordance with manufacturer's instructions approved submittals and in proper relationship with adjacent construction.

3.4 FIELD QUALITY CONTROL

3.4.1 Field Inspection: Coordinate field inspection in accordance with appropriate sections in Division 01.

3.4.2 Manufacturer's Services: Coordinate manufacturer's services in accordance with appropriate sections in Division 01.

3.5 CLEANING AND PROTECTION

3.5.1 Clean products in accordance with the manufacturers recommendations.

3.5.2 Touch-up, repair or replace damaged products before Substantial Completion.

3.6 PAINT SCHEDULE (LEED-V4 NC/CI/CS COMPLIANT)

3.6.1 Interior Paints and Coatings:3.6.1.1 Drywall and Plaster: Walls, Ceilings, Gypsum Board and similar items

3.6.1.1.1 Smooth Finishes:3.6.1.1.1.1 Available Primers:

3.6.1.1.1.1.1 TEX-COTE Primer 27 W.3.6.1.1.1.1.2 TEX-COTE TEX-BOND Primer.

3.6.1.1.1.2 Flat/Matte Finish Systems:3.6.1.1.1.2.1 Flat/Matte Finish:

3.6.1.1.1.2.1.1 First Coat: TEX-COTE Primer 27 W.3.6.1.1.1.2.1.2 Second Coat: TEX-COTE COLOR-COTE DF.

Flat Acrylic Coating.3.6.1.1.1.3 Low Sheen Finish Systems:

3.6.1.1.1.3.1 Eggshell Finish:3.6.1.1.1.3.1.1 First Coat: TEX-COTE Primer 27 W.3.6.1.1.1.3.1.2 Second Coat: TEX-COTE COLOR-COTE. Satin

Acrylic Coating.3.6.1.1.1.4 Semi-Gloss Finishes:

3.6.1.1.1.4.1 Semi-Gloss Finish:3.6.1.1.1.4.1.1 First Coat: TEX-COTE Primer 27 W.3.6.1.1.1.4.1.2 Second Coat: TEX-COTE TRIM-COTE. Acrylic

interior semi-gloss.3.6.1.1.2 Multi-Color Finish System:

3.6.1.1.2.1 Available Primers:3.6.1.1.2.1.1 TEX-COTE Primer 27 W.3.6.1.1.2.1.2 TEX-COTE TEX-BOND Primer.

3.6.1.1.2.2 COLOR-TEX:3.6.1.1.2.2.1 1st Coat: TEX-COTE COLOR-TEX Multi-Color Base

Coat.3.6.1.1.2.2.2 2nd Coat: TEX-COTE COLOR-TEX Multi-Color Finish

Coat.3.6.1.1.2.3 TEX-TURA:

09 96 00-16

3.6.1.1.2.3.1 1st Coat: TEX-COTE TEX-TURA Base Coat.3.6.1.1.2.3.2 2nd Coat: TEX-COTE TEX-TURA Finish Coat.

3.6.1.1.3 Dry-Erase Coatings:3.6.1.1.3.1 Available Primers:

3.6.1.1.3.1.1 TEX-COTE Primer 27 W.3.6.1.1.3.1.2 TEX-COTE TEX-BOND Primer.

3.6.1.1.3.2 Eraser-Cote White Dry Erase Coating:3.6.1.1.3.2.1 1st Coat: TEX-COTE ERASER-COTE. White Part A and

Part B mixed.3.6.1.1.3.3 Eraser Coat Clear Dry Erase Coating:

3.6.1.1.3.3.1 1st Coat: TEX-COTE ERASER-COTE. Clear Part A and Part B mixed.

3.6.1.2 Concrete and Masonry: Other than CMU.3.6.1.2.1 Smooth Finishes:

3.6.1.2.1.1 Available Crack Fillers:3.6.1.2.1.1.1 TEX-COTE Flex-Patch Patching Compound.

3.6.1.2.1.1.1.1 Texture: Standard.3.6.1.2.1.1.1.2 Texture: Smooth (butter texture).



3.6.1.2.1.3.1.1 Finish Coat: TEX-COTE COLOR-COTE DF. Flat Acrylic Coating.

3.6.1.2.1.4 Low Sheen Finish Systems:3.6.1.2.1.4.1 Eggshell Finish:

3.6.1.2.1.4.1.1 Finish Coat: TEX-COTE COLOR-COTE. Satin Acrylic Coating.

3.6.1.2.1.5 Semi-Gloss Finishes:3.6.1.2.1.5.1 Semi-Gloss Finish:

3.6.1.2.1.5.1.1 Finish Coat: TEX-COTE. TRIM-COTE. Acrylic interior semi-gloss.

3.6.1.2.2 Multi-Color Finish System:3.6.1.2.2.1 Available Crack Fillers:

3.6.1.2.2.1.1 TEX-COTE Flex-Patch Patching Compound.3.6.1.2.2.1.1.1 Texture: Standard.3.6.1.2.2.1.1.2 Texture: Smooth (butter texture).






3.6.1.3 Concrete Masonry Units:3.6.1.3.1 Smooth Finishes:

3.6.1.3.1.1 Available Crack Fillers:3.6.1.3.1.1.1 TEX-COTE Latex Block Filler.3.6.1.3.1.1.2 TEX-COTE Flex-Patch Patching Compound.


09 96 00-17

3.6.1.3.1.2 Available Primers:3.6.1.3.1.2.1 TEX-COTE Primer 27 W.3.6.1.3.1.2.2 TEX-COTE TEX-BOND Primer


3.6.1.3.1.3.1.1 Finish Coat: TEX-COTE COLOR-COTE DF. Flat Acrylic Coating.

3.6.1.3.1.4 Low Sheen Finish Systems:3.6.1.3.1.4.1 Eggshell Finish:

3.6.1.3.1.4.1.1 Finish Coat: TEX-COTE COLOR-COTE. Satin Acrylic Coating.

3.6.1.3.1.5 Semi-Gloss Finishes:3.6.1.3.1.5.1 Semi-Gloss Finish:

3.6.1.3.1.5.1.1 Finish Coat: TEX-COTE TRIM-COTE Acrylic interior semi-gloss.

3.6.1.3.2 Multi-Color Finish System:3.6.1.3.2.1 Available Crack Fillers:

3.6.1.3.2.1.1 TEX-COTE Latex Block Filler.3.6.1.3.2.1.2 TEX-COTE Flex-Patch Patching Compound.


3.6.1.3.2.2 Available Primers:3.6.1.3.2.2.1 TEX-COTE Primer 27 W.3.6.1.3.2.2.2 TEX-COTE TEX-BOND Primer





3.6.1.4 Concrete Floor Coatings:3.6.1.4.1 High Performance Two Component Systems

3.6.1.4.1.1 Available Crack Fillers:3.6.1.4.1.1.1 Roadware Concrete Mender.

3.6.1.4.1.2 Cool-Tex Concrete Floor and Deck System:3.6.1.4.1.2.1 1st Coat: COOL-TEX Two Component Epoxy Base with

Texture3.6.1.4.1.2.2 2nd Coat: TEX-COTE CLEAR-GUARD. Two Component

Urethane Clear Coat.3.6.1.4.2 Single Component Latex Systems

3.6.1.4.2.1 Available Crack Fillers:3.6.1.4.2.1.1 Roadware Concrete Mender:

3.6.1.4.2.2 Cool-Tec Concrete Floor and Deck System:3.6.1.4.2.2.1 First Coat: TEX-COTE COOL-TEC Waterborne High

Build Acrylic Base Coat (Sand Texture).3.6.1.4.2.2.2 Second Coat: TEX-COTE CLEAR-SEAL: Acrylic

Waterborne Protective Sealer.

3.6.2 Exterior High-Performance Paints and Coatings:3.6.2.1 Exterior Paint Systems:

3.6.2.1.1 Concrete and Masonry (Cast in Place, Stucco, Tilt Wall, Fiber Reinforced Panels)

3.6.2.1.1.1 Smooth Finishes:3.6.2.1.1.1.1 Available Crack Fillers:

09 96 00-18

3.6.2.1.1.1.1.1 TEX-COTE Flex-Patch Patching Compound.3.6.2.1.1.1.1.1.1 Texture: Standard.3.6.2.1.1.1.1.1.2 Texture: Smooth (butter texture).

3.6.2.1.1.1.2 Available Primers:3.6.2.1.1.1.2.1 TEX-COTE XL 70 W.3.6.2.1.1.1.2.2 TEX-COTE Primer 27 W.3.6.2.1.1.1.2.3 TEX-COTE COOLWALL RECOAT Primer.3.6.2.1.1.1.2.4 TEX-COTE TEX-BOND Primer.

3.6.2.1.1.1.3 Reflect-Tec IR Heat Reflective KYNAR Coatings:3.6.2.1.1.1.3.1 Satin Finish System:

3.6.2.1.1.1.3.1.1 First Coat: TEX-COTE Primer 27W.3.6.2.1.1.1.3.1.2 Second Coat:TEX-COTE REFLECT-

TEC Semi-Gloss Finish.3.6.2.1.1.1.4 COOLWALL IR Heat Reflective Wall Coating System

3.6.2.1.1.1.4.1 Satin Finish System:3.6.2.1.1.1.4.1.1 First Coat: TEX-COTE Classic Primer3.6.2.1.1.1.4.1.2 Second Coat: TEX-COTE COOLWALL

Satin3.6.2.1.1.1.4.1.3 Finish Coat: TEX-COTE COOLWALL

Satin3.6.2.1.1.1.4.2 Flat/Matte Finish System:

3.6.2.1.1.1.4.2.1 First Coat: TEX-COTE Classic Primer3.6.2.1.1.1.4.2.2 Second Coat: TEX-COTE COOLWALL

HR Flat3.6.2.1.1.1.4.2.3 Finish Coat: TEX-COTE COOLWALL

HR Flat3.6.2.1.1.1.5 TEX-COTE 600 High Build Coating: Smooth.

3.6.2.1.1.1.5.1 Flat/Matte Finish System:3.6.2.1.1.1.5.1.1 First Coat: TEX-COTE XL-70 W Primer.3.6.2.1.1.1.5.1.2 Second Coat: TEX-COTE 600 High

Build Smooth Coating.3.6.2.1.1.1.6 TEX-COTE XL-70W High Build Coating - Smooth

3.6.2.1.1.1.6.1 Flat/Matte Finish System:3.6.2.1.1.1.6.1.1 First Coat: TEX-COTE XL-70 W Primer.3.6.2.1.1.1.6.1.2 Second Coat: TEX-COTE XL-70W High

Build Smooth Coating3.6.2.1.1.1.7 TEX-COTE 300 High Build Coating - Smooth


Build Smooth Coating3.6.2.1.1.1.8 TEX-COTE XL-70 Original Solvent-Based High Build

Coating - Smooth3.6.2.1.1.1.8.1 Flat/Matte Finish System:

3.6.2.1.1.1.8.1.1 First Coat: TEX-COTE XL-70 Original Solvent-Based Primer

3.6.2.1.1.1.8.1.2 Second Coat: TEX-COTE XL-70 Original High Build Smooth Coating

3.6.2.1.1.2 Textured Finishes:3.6.2.1.1.2.1 Available Crack Fillers:


3.6.2.1.1.2.2 Available Primers:3.6.2.1.1.2.2.1 TEX-COTE XL 70 W.3.6.2.1.1.2.2.2 TEX-COTE Primer 27 W.

09 96 00-19

3.6.2.1.1.2.2.3 TEX-COTE TEX-BOND Primer3.6.2.1.1.2.3 COOLWALL IR Heat Reflective Wall Coating System:

3.6.2.1.1.2.3.1 Satin Finish System:3.6.2.1.1.2.3.1.1 First Coat: TEX-COTE Textured Primer

Sand, Fine, or Coarse.3.6.2.1.1.2.3.1.2 Second Coat: TEX-COTE COOLWALL



3.6.2.1.1.2.3.2.1 First Coat: TEX-COTE Textured Primer Sand, Fine, or Coarse.

3.6.2.1.1.2.3.2.2 Second Coat: TEX-COTE COOLWALL HR Flat

3.6.2.1.1.2.3.2.3 Finish Coat: TEX-COTE COOLWALL HR Flat

3.6.2.1.1.2.4 TEX-COTE 600 High Build Coating: Textured.3.6.2.1.1.2.4.1 Flat/Matte Finish System:

3.6.2.1.1.2.4.1.1 First Coat: TEX-COTE XL-70 W Primer.3.6.2.1.1.2.4.1.2 Second Coat: TEX-COTE 600 High

Build Textured Coating Sand, Fine, or Coarse.3.6.2.1.1.2.5 TEX-COTE XL-70W High Build Coating: Textured.

3.6.2.1.1.2.5.1 Flat/Matte Finish System:3.6.2.1.1.2.5.1.1 First Coat: TEX-COTE XL-70 W Primer.3.6.2.1.1.2.5.1.2 Second Coat: TEX-COTE XL-70W High

Build Textured Coating Sand, Fine, or Coarse.3.6.2.1.1.2.6 TEX-COTE 300 High Build Coating - Textured


Build Textured Coating Sand, Fine, or Coarse3.6.2.1.1.2.7 TEX-COTE XL-70 Original Solvent-Based High Build

Coating - Textured3.6.2.1.1.2.7.1 Flat/Matte Finish System:

3.6.2.1.1.2.7.1.1 First Coat: TEX-COTE XL-70 Original Solvent-Based Primer

3.6.2.1.1.2.7.1.2 Second Coat: TEX-COTE XL-70 Original High Build Textured Coating Sand, Fine, or Coarse

3.6.2.1.1.3 Specialty Finishes:3.6.2.1.1.3.1 Available Crack Fillers:


3.6.2.1.1.3.2 High Performance Clear Polyurethanes:3.6.2.1.1.3.2.1 TEX-COTE CLEARGUARD Two-Component

Waterborne Urethane - Gloss3.6.2.1.1.3.2.2 TEX-COTE CLEARGUARD Two-Component

Waterborne Urethane - Low Luster3.6.2.1.1.3.3 Anti-Graffiti Coating Systems:

3.6.2.1.1.3.3.1 Sacrificial Anti-Graffiti Coatings:3.6.2.1.1.3.3.1.1 TEX-COTE Sacrificial Graffiti-Guard.

3.6.2.1.1.3.3.2 Permanent Anti-Graffiti Coatings:3.6.2.1.1.3.3.2.1 TEX-COTE GRAFFITI GARD IV Clear.3.6.2.1.1.3.3.2.2 Finish: Gloss.3.6.2.1.1.3.3.2.3 Finish: Low luster,

09 96 00-20

3.6.2.1.1.3.3.2.4 TEX-COTE Graffiti-Guard S Clear.3.6.2.1.2 Concrete Masonry Units:

3.6.2.1.2.1 Smooth Finishes:3.6.2.1.2.1.1 Available Crack Fillers:


3.6.2.1.2.1.2 Available Primer and Block Fillers3.6.2.1.2.1.2.1 TEX-COTE XL 70 W.3.6.2.1.2.1.2.2 TEX-COTE Latex Block Filler.

3.6.2.1.2.1.2.2.1 Texture: Standard.3.6.2.1.2.1.2.2.2 Texture: Smooth (butter texture).

3.6.2.1.2.1.2.3 TEX-COTE COOLWALL RECOAT Primer.3.6.2.1.2.1.3 REFLECT-TEC IR Heat Reflective KYNAR Coating:

3.6.2.1.2.1.3.1 Satin Finish System:3.6.2.1.2.1.3.1.1 First Coat: TEX-COTE BLOCK FILLER.3.6.2.1.2.1.3.1.2 Second Coat: TEX-COTE Primer 27W.3.6.2.1.2.1.3.1.3 Finish Coat: TEX-COTE REFLECT-TEC

Semi-Gloss Finish.3.6.2.1.2.1.4 COOLWALL IR Heat Reflective Wall Coating System

3.6.2.1.2.1.4.1 Satin Finish System:3.6.2.1.2.1.4.1.1 First Coat: TEX-COTE LATEX BLOCK

FILLER3.6.2.1.2.1.4.1.2 Second Coat: TEX-COTE Classic

Primer3.6.2.1.2.1.4.1.3 Finish Coat: TEX-COTE COOLWALL


3.6.2.1.2.1.4.2.1 First Coat: TEX-COTE LATEX BLOCK FILLER

3.6.2.1.2.1.4.2.2 Second Coat: TEX-COTE Classic Primer


3.6.2.1.2.1.5 COLOR-COTE High Build Finishing System3.6.2.1.2.1.5.1 Satin Finish System:


3.6.2.1.2.1.5.1.2 Second Coat: TEX-COTE XL-70W Primer.

3.6.2.1.2.1.5.1.3 Finish Coat: TEX-COTE COLOR-COTE Satin

3.6.2.1.2.1.5.2 Flat/Matte Finish System:3.6.2.1.2.1.5.2.1 First Coat: TEX-COTE BLOCK FILLER.3.6.2.1.2.1.5.2.2 Second Coat: TEX-COTE XL-70W

Primer.3.6.2.1.2.1.5.2.3 Finish Coat: TEX-COTE DF COLOR-

COTE Flat3.6.2.1.2.1.6 TEX-COTE 600 High Build Coating - Smooth

3.6.2.1.2.1.6.1 Flat/Matte Finish System:3.6.2.1.2.1.6.1.1 First Coat: TEX-COTE BLOCK FILLER.3.6.2.1.2.1.6.1.2 Second Coat: TEX-COTE XL-70W

Primer.3.6.2.1.2.1.6.1.3 Finish Coat: TEX-COTE 600 High Build

Smooth Coating3.6.2.1.2.1.7 TEX-COTE XL-70W High Build Coating - Smooth

09 96 00-21

3.6.2.1.2.1.7.1 Flat/Matte Finish System:3.6.2.1.2.1.7.1.1 First Coat: TEX-COTE BLOCK FILLER3.6.2.1.2.1.7.1.2 Second Coat: TEX-COTE XL-70W

Primer3.6.2.1.2.1.7.1.3 Finish Coat: TEX-COTE XL-70W High

Build Smooth Coating3.6.2.1.2.1.8 TEX-COTE 300 High Build Coating - Smooth

3.6.2.1.2.1.8.1 Flat/Matte Finish System:3.6.2.1.2.1.8.1.1 First Coat: TEX-COTE BLOCK FILLER3.6.2.1.2.1.8.1.2 Second Coat: TEX-COTE XL-70W

Primer3.6.2.1.2.1.8.1.3 Finish Coat: TEX-COTE 300 High Build

Smooth Coating3.6.2.1.2.1.9 TEX-COTE XL-70 Original Solvent-Based High Build

Coating - Smooth3.6.2.1.2.1.9.1 Flat/Matte Finish System:

3.6.2.1.2.1.9.1.1 First Coat: TEX-COTE BLOCK FILLER3.6.2.1.2.1.9.1.2 SecondCoat: TEX-COTE XL-70

Original Solvent-Based Primer3.6.2.1.2.1.9.1.3 Finish Coat: TEX-COTE XL-70 Original

High Build Smooth Coating3.6.2.1.2.2 Textured Finishes:

3.6.2.1.2.2.1 Available Crack Fillers:3.6.2.1.2.2.1.1 TEX-COTE Flex-Patch Patching Compound.


3.6.2.1.2.2.2 Available Primer and Block Fillers3.6.2.1.2.2.2.1 TEX-COTE XL 70 W Primer.3.6.2.1.2.2.2.2 TEX-COTE Latex Block Filler.


3.6.2.1.2.2.2.3 TEX-COTE COOLWALL RECOAT Primer3.6.2.1.2.2.3 COOLWALL IR Heat Reflective Wall Coating System

3.6.2.1.2.2.3.1 Satin Finish System:3.6.2.1.2.2.3.1.1 First Coat: TEX-COTE LATEX BLOCK

FILLER3.6.2.1.2.2.3.1.2 Second Coat: TEX-COTE Textured

Primer Sand, Fine, or Coarse3.6.2.1.2.2.3.1.3 Finish Coat: TEX-COTE COOLWALL



3.6.2.1.2.2.3.2.2 Second Coat: TEX-COTE Textured Primer Sand, Fine, or Coarse


3.6.2.1.2.2.4 TEX-COTE 600 High Build Coating - Textured3.6.2.1.2.2.4.1 Flat/Matte Finish System:


3.6.2.1.2.2.4.1.2 Second Coat: TEX-COTE XL-70W Primer

3.6.2.1.2.2.4.1.3 Finish Coat: TEX-COTE 600 High Build Textured Coating Sand, Fine, or Coarse

3.6.2.1.2.2.5 TEX-COTE XL-70W High Build Coating - Textured

09 96 00-22

3.6.2.1.2.2.5.1 Flat/Matte Finish System:3.6.2.1.2.2.5.1.1 First Coat: TEX-COTE LATEX BLOCK

FILLER3.6.2.1.2.2.5.1.2 Second Coat: TEX-COTE XL-70W

Primer3.6.2.1.2.2.5.1.3 Finish Coat: TEX-COTE XL-70W High

Build Textured Coating Sand, Fine, or Coarse3.6.2.1.2.2.6 TEX-COTE 300 High Build Coating - Textured

3.6.2.1.2.2.6.1 Flat/Matte Finish System:3.6.2.1.2.2.6.1.1 First Coat: TEX-COTE LATEX BLOCK

FILLER3.6.2.1.2.2.6.1.2 Second Coat: TEX-COTE XL-70W

Primer3.6.2.1.2.2.6.1.3 Finish Coat: TEX-COTE 300 High Build

Textured Coating Sand, Fine, or Coarse3.6.2.1.2.2.7 TEX-COTE XL-70 Original Solvent-Based High Build

Coating - Textured3.6.2.1.2.2.7.1 Flat/Matte Finish System:


3.6.2.1.2.2.7.1.2 SecondCoat: TEX-COTE XL-70 Original Solvent-Based Primer

3.6.2.1.2.2.7.1.3 Finish Coat: TEX-COTE XL-70 Original High Build Textured Coating Sand, Fine, or Coarse

3.6.2.1.2.3 Specialty Finishes:3.6.2.1.2.3.1 Available Crack Fillers:


3.6.2.1.2.3.2 High Performance Clear Polyurethanes:3.6.2.1.2.3.2.1 TEX-COTE CLEARGUARD Two-Component

Waterborne Urethane - Gloss3.6.2.1.2.3.2.2 TEX-COTE CLEARGUARD Two-Component

Waterborne Urethane - Low Luster3.6.2.1.2.3.3 Anti-Graffiti Coating Systems:

3.6.2.1.2.3.3.1 Sacrificial Anti-Graffiti Coatings:3.6.2.1.2.3.3.1.1 TEX-COTE Sacrificial Graffiti-Guard:

3.6.2.1.2.3.3.2 Permanent Anti-Graffiti Coatings:3.6.2.1.2.3.3.2.1 TEX-COTE GRAFFITI GARD IV Clear3.6.2.1.2.3.3.2.2 TEX-COTE Graffiti-Guard S Clear.

3.6.2.1.3 Concrete Floors: Patios, Walkways, Driveways, Pool Decks:3.6.2.1.3.1 High Performance Coating Systems:

3.6.2.1.3.1.1 First Coat: TEX-COTE COOL-TEX Two-Component High Build Epoxy Base Coat (Sand Texture)

3.6.2.1.3.1.2 Finish Coat: TEX-COTE CLEARGUARD Two-Component Waterborne Urethane - Gloss or Low Luster

3.6.2.1.3.2 High Build Waterborne Acrylic Systems:3.6.2.1.3.2.1 First Coat: TEX-COTE COOL-TEC Waterborne High

Build Acrylic Base Coat (Sand Texture)3.6.2.1.3.2.2 Second Coat: TEX-COTE CLEAR-SEAL: Acrylic

Waterborne Protective Sealer.3.6.2.1.3.3 Concrete Stain Systems, Silicone Acrylic:

3.6.2.1.3.3.1 First Coat: TEX-COTE Rainstopper Ultra Silicone Acrylic Concrete Stain.

3.6.2.1.3.3.2 Second Coat: TEX-COTE Rainstopper Ultra Silicone Acrylic Concrete Stain.

09 96 00-23

3.6.2.1.3.4 Concrete Stain Systems, Acrylic:3.6.2.1.3.4.1 First Coat: TEX-COTE Rainstopper Acrylic Concrete

Stain.3.6.2.1.3.4.2 Second Coat: TEX-COTE Rainstopper Acrylic Concrete

Stain.3.6.2.1.4 Metal: Aluminum, Galvanized, Ferrous, Steel:

3.6.2.1.4.1 Smooth Finishes:3.6.2.1.4.1.1 Available Primers:

3.6.2.1.4.1.1.1 TEX-COTE Metal-Prime Primer3.6.2.1.4.1.2 REFLECT-TEC IR Heat Reflective KYNAR Coating

3.6.2.1.4.1.2.1 Satin Finish System:3.6.2.1.4.1.2.1.1 First Coat: TEX-COTE Metal Prime

Primer3.6.2.1.4.1.2.1.2 Second Coat: TEX-COTE REFLECT-

TEC Semi-Gloss Finish.3.6.2.1.4.1.2.1.3 Finish Coat: TEX-COTE REFLECT-TEC

Semi-Gloss Finish.3.6.2.1.4.1.3 COOLWALL IR Heat Reflective Wall Coating System

3.6.2.1.4.1.3.1 Satin Finish System:3.6.2.1.4.1.3.1.1 First Coat: TEX-COTE Metal Prime

Primer3.6.2.1.4.1.3.1.2 Second Coat: TEX-COTE COOLWALL



3.6.2.1.4.1.3.2.1 First Coat: TEX-COTE Metal Prime Primer



3.6.2.1.4.1.4 TEX-COTE 600 High Build Coating - Smooth3.6.2.1.4.1.4.1 Flat/Matte Finish System:

3.6.2.1.4.1.4.1.1 First Coat: TEX-COTE Metal Prime Primer

3.6.2.1.4.1.4.1.2 Second Coat: TEX-COTE 600 High Build Smooth Coating

3.6.2.1.4.2 Textured Finishes:3.6.2.1.4.2.1 Available Primers:

3.6.2.1.4.2.1.1 TEX-COTE Metal-Prime Primer:3.6.2.1.4.2.2 COOLWALL IR Heat Reflective Wall Coating System

3.6.2.1.4.2.2.1 Satin Finish System:3.6.2.1.4.2.2.1.1 First Coat: TEX-COTE Textured Primer

HD Sand, Fine, or Coarse3.6.2.1.4.2.2.1.2 Second Coat: TEX-COTE COOLWALL



3.6.2.1.4.2.2.2.1 First Coat: TEX-COTE Textured Primer HD Sand, Fine, or Coarse



09 96 00-24

3.6.2.1.4.2.3 TEX-COTE 600 High Build Coating: Textured.3.6.2.1.4.2.3.1 Flat/Matte Finish System:

3.6.2.1.4.2.3.1.1 First Coat: TEX-COTE METAL PRIME Primer

3.6.2.1.4.2.3.1.2 Second Coat:TEX-COTE 600 High Build Textured Coating. Sand, fine, or course.

3.6.2.1.5 Wood: Trim Soffits, Plywood:3.6.2.1.5.1 Available Primers:

3.6.2.1.5.1.1 TEX-COTE Primer 27 W.3.6.2.1.5.1.2 TEX-COTE COOLWALL RECOAT Primer3.6.2.1.5.1.3 TEX-COTE COOLWALL Classic Primer.

3.6.2.1.5.2 REFLECT-TEC IR Heat Reflective KYNAR Coating3.6.2.1.5.2.1 Satin Finish System:

3.6.2.1.5.2.1.1 First Coat: TEX-COTE Primer No. 273.6.2.1.5.2.1.2 Second Coat: TEX-COTE REFLECT-TEC Semi-

Gloss Finish3.6.2.1.5.3 COOLWALL IR Heat Reflective Wall Coating System

3.6.2.1.5.3.1 Satin Finish System:3.6.2.1.5.3.1.1 First Coat: TEX-COTE COOLWALL Classic

Primer3.6.2.1.5.3.1.2 Second Coat: TEX-COTE COOLWALL Satin3.6.2.1.5.3.1.3 Finish Coat: TEX-COTE COOLWALL Satin

3.6.2.1.5.3.2 Flat/Matte Finish System:3.6.2.1.5.3.2.1 First Coat: TEX-COTE COOLWALL Classic

Primer3.6.2.1.5.3.2.2 Second Coat: TEX-COTE COOLWALL HR Flat3.6.2.1.5.3.2.3 Finish Coat: TEX-COTE COOLWALL HR Flat

3.6.2.1.5.4 TEX-COTE 600 High Build Coating: Smooth.3.6.2.1.5.4.1 Flat/Matte Finish System:

3.6.2.1.5.4.1.1 First Coat: TEX-COTE Primer 27 W.3.6.2.1.5.4.1.2 Second Coat: TEX-COTE 600 High Build

Smooth Coating.3.6.2.1.5.5 COLOR-COTE: Smooth.

3.6.2.1.5.5.1 Satin Finish System:3.6.2.1.5.5.1.1 First Coat: TEX-COTE Primer 27 W.3.6.2.1.5.5.1.2 Second Coat: TEX-COTE COLOR-COTE Satin

Acrylic Coating.3.6.2.1.5.5.2 Flat/Matte Finish System:

3.6.2.1.5.5.2.1 First Coat: TEX-COTE Primer 27 W.3.6.2.1.5.5.2.2 Second Coat: TEX-COTE DF COLOR-COTE

Flat Coating.

END OF SECTION

09 96 00-25

Documents

file · Web viewSECTION 09 96 00. TEXTURED AND HIGH BUILD COATINGS. Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2018 - 2018 ARCAT, Inc