-Tex Tri - mtcchem.netmtcchem.net/images/fichesENv4Web.pdf · In 2010, Tri-Tex co inc. has acquired Chemor Inc. to continue ... C-635 C-750 CRD-C 621 NCHRP RAPPORT 244 WALL AND CEILINGS

Tri-T

ex co

inc.

CONSTRUCTION

CONSTRUCTION

Cons

tructi

on Ch

emica

lsData SheetsAdhesives & BindersGrouts WaterproofingMortarsPrimers & Coatings SealersSeamless FloorsMiscellaneous

Divisions3,4,7 & 9

2 Tri-Tex co inc.

CONSTRUCTIONc

Chemor Inc. offers greater flexibility in development and manufacturing of customized products that meet specific customer requirements, which goes beyond the criteria of competition large-scale production.

Through the years, thanks to a dynamic and experienced Research and Development team and Chemor Inc. has earned a solid reputation for innovation and reliability. This reputation is particularly noticeable by its involvement in prestigious projects such as construction of several metro stations (Cartier and Concorde), the Casino de Charlevoix, IREQ and several other Hydro-Quebec plants and most recently, the fountain of Tournay and the Champlain promenades in the Quebec City region.

In 2010, Tri-Tex co inc. has acquired Chemor Inc. to continue the adventure.

HistoryEstablished in 1964 by Dr. Ted H. Waid.

Initially, the company was focused on developing and manufacturing of adhesives for footwear.

However, in the late sixties, the company has focused its activities towards the chemistry of epoxy and began to develop innovative flooring made of epoxy-based polymers. In the seventies, Chemor Inc. managed to develop its first waterproof coatings synthesized from coal tar or epoxy solvents and thereby acquired a strong expertise in the field of coating for parking.

Today Chemor Inc. is serving the building industries, construction and public works. The diverse range of Chemor Inc. specialty chemicals is for new construction, renovation and maintenance.

Chemor Inc. managed to distinguish itself from other international and U.S. players in developing a more comprehensive range of flooring solutions based on polymers such as adhesives, binders, grouts, waterproof coatings, mortars, primers, sealers , coatings and decorative products for protection against weathering and chemicals. This helps to provide contractors and architects fully integrated and complete coating solutions.

MissionTo be the industry leader in our field, as acknowledged by our customers and suppliers, in offering an unparalleled level of technical service and customer satisfaction.The commitment of ever y employee will ensure our continued growth and success.

Your needs create our products.Ask us!

3 Tri-Tex co inc.

CONSTRUCTIONc

Primers & Coatings (cont’d) Chemorclad 2020 76Chemorclad 9000 79Chemorclad 9030 81Chemorclad 9100 83Chemorclad 9200 85Chemorclad 9600 87Chemorlast 89

SealersChemordur 25 92Chemorseal AW 10 94Chemorseal AW 25 96Chemorseal E 98Chemorseal N 20 100Chemorseal N 40 102Chemorseal N 100 104Chemorseal P 106

Seamless floorsChemoraz E 109Chemoroc 111Chemoroc HD 114Chemoroc LT 116Chemorquartz HDB 118Chemorquartz SLB 120Chemorquartz TR 122

MiscellaneousChemorplex A 124MetPrep 126

ContentsStandards Table 4Table of Primers 7Application Table 8Spray Table 12Coatings Table 13

ProductsAdhesives & BindersChemorbond 14Chemorbond 100 16Chemorcrete WR 18Chemorset 100 G 20Chemorset 100 LV 22Chemorset 100 M 24Chemorset 400 SL/NS 27

GroutsChemorgrout 100 29Chemorgrout 200 32

WaterproofingChemordek 34Chemorflex 350 37Chemormec 40Chemorpark III 44

MortarsChemorciment 525 48Chemorfil E 51Chemorgrout 200 / Chemorcrete WR 22 53Chemorpatch 66 55

Primers & Coatings Chemorclad 200 57Chemorclad 200 CSL 61Chemorclad 250 65Chemorclad 300 SL 69Chemorclad 1010 73

4 Tri-Tex co inc.

CONSTRUCTIONc

Standards

81-GP-6MCAN/ONGC 1,153-MCAN/ONGC 1,165-M/MODIFIED81-GP-5M81-GP-4-MCAN/CSA S413C-836C-881C-957C-1059/TYPE IIC-695C-638C-882C-2240C-624C-109C-293C-531C-666C-348C-579E-831C-4060C-580C-307C-506C-672C-469C-570C-2244C-412C-790E-96C-413C-522C-1308C-4541C-635C-750CRD-C 621NCHRP RAPPORT #244WALL AND CEILINGS COATINGSWATER AND FOOD INTERNAL TANK COATINGS

COATINGS FOR FLOORINGSTRUCTURAL COATINGS

Canadian general standards board (CGSB)

ACNORASTM

U.S. Corps of EngineersU.S. Transportation BoardCanadian Food Inspection Agency

Chem

orbo

nd

Chem

orbo

nd 1

00

Chem

orcr

ete

WR

Chem

orse

t 100

G

Chem

orse

t 100

LV

Chem

orse

t 100

M

Chem

orse

t 400

SL/N

S

Chem

ordu

r 25

Chem

orse

al A

W 1

0

Chem

orse

al A

W 2

5

Chem

orse

al E

Chem

orse

al N

20

Chem

orse

al N

40

Chem

orse

al N

100

Chem

orse

al P

Chem

orgr

out 1

00

Chem

orgr

out 2

00

Chem

orci

men

t 525

Chem

orfil

E

Chem

orgr

out 2

00 e

t

Chem

orcr

ete

WR

22

Chem

orpa

tch

66

Chem

oraz

E

Chem

oroc

Chem

oroc

HD

Chem

oroc

LT

Chem

orqu

artz

HB

D

Chem

orqu

artz

SLB

Chem

orqu

artz

TR

Chem

orfle

x 35

0

Chem

orre

c

Chem

orpa

rk II

I

Chem

orde

k

Chem

orcl

ad 9

000

Chem

orcl

ad 9

030

Chem

orcl

ad 9

100

Chem

orcl

ad 9

200

Chem

orcl

ad 9

600

Chem

orcl

ad 2

00

Chem

orcl

ad 2

00C

SL

Chem

orcl

ad 2

50

Chem

orcl

ad 3

00 S

L

Chem

orcl

ad 1

010

Chem

orcl

ad 2

020

Chem

orla

st

Adhesives & Binders

StandardsSpecifications

Sealers Grouts Mortars Seamless floors

Family ProductsWaterproofing Primers Coatings

Meets industry standards

5 Tri-Tex co inc.

CONSTRUCTIONc

Standards




ACNORASTM


Chem

orbo

nd

Chem

orbo

nd 1

00

Chem

orcr

ete

WR

Chem

orse

t 100

G

Chem

orse

t 100

LV

Chem

orse

t 100

M

Chem

orse

t 400

SL/N

S

Chem

ordu

r 25

Chem

orse

al A

W 1

0

Chem

orse

al A

W 2

5

Chem

orse

al E

Chem

orse

al N

20

Chem

orse

al N

40

Chem

orse

al N

100

Chem

orse

al P

Chem

orgr

out 1

00

Chem

orgr

out 2

00

Chem

orci

men

t 525

Chem

orfil

E

Chem

orgr

out 2

00 e

t

Chem

orcr

ete

WR

22

Chem

orpa

tch

66

Chem

oraz

E

Chem

oroc

Chem

oroc

HD

Chem

oroc

LT

Chem

orqu

artz

HB

D

Chem

orqu

artz

SLB

Chem

orqu

artz

TR

Chem

orfle

x 35

0

Chem

orre

c

Chem

orpa

rk II

I

Chem

orde

k

Chem

orcl

ad 9

000

Chem

orcl

ad 9

030

Chem

orcl

ad 9

100

Chem

orcl

ad 9

200

Chem

orcl

ad 9

600

Chem

orcl

ad 2

00

Chem

orcl

ad 2

00C

SL

Chem

orcl

ad 2

50

Chem

orcl

ad 3

00 S

L

Chem

orcl

ad 1

010

Chem

orcl

ad 2

020

Chem

orla

st

Adhesives & Binders







ACNORASTM


Chem

orbo

nd

Chem

orbo

nd 1

00

Chem

orcr

ete

WR

Chem

orse

t 100

G

Chem

orse

t 100

LV

Chem

orse

t 100

M

Chem

orse

t 400

SL/N

S

Chem

ordu

r 25

Chem

orse

al A

W 1

0

Chem

orse

al A

W 2

5

Chem

orse

al E

Chem

orse

al N

20

Chem

orse

al N

40

Chem

orse

al N

100

Chem

orse

al P

Chem

orgr

out 1

00

Chem

orgr

out 2

00

Chem

orci

men

t 525

Chem

orfil

E

Chem

orgr

out 2

00 e

t

Chem

orcr

ete

WR

22

Chem

orpa

tch

66

Chem

oraz

E

Chem

oroc

Chem

oroc

HD

Chem

oroc

LT

Chem

orqu

artz

HB

D

Chem

orqu

artz

SLB

Chem

orqu

artz

TR

Chem

orfle

x 35

0

Chem

orre

c

Chem

orpa

rk II

I

Chem

orde

k

Chem

orcl

ad 9

000

Chem

orcl

ad 9

030

Chem

orcl

ad 9

100

Chem

orcl

ad 9

200

Chem

orcl

ad 9

600

Chem

orcl

ad 2

00

Chem

orcl

ad 2

00C

SL

Chem

orcl

ad 2

50

Chem

orcl

ad 3

00 S

L

Chem

orcl

ad 1

010

Chem

orcl

ad 2

020

Chem

orla

st

Adhesives & Binders





6 Tri-Tex co inc.

CONSTRUCTIONc

Standards




ACNORASTM


Chem

orbo

nd

Chem

orbo

nd 1

00

Chem

orcr

ete

WR

Chem

orse

t 100

G

Chem

orse

t 100

LV

Chem

orse

t 100

M

Chem

orse

t 400

SL/N

S

Chem

ordu

r 25

Chem

orse

al A

W 1

0

Chem

orse

al A

W 2

5

Chem

orse

al E

Chem

orse

al N

20

Chem

orse

al N

40

Chem

orse

al N

100

Chem

orse

al P

Chem

orgr

out 1

00

Chem

orgr

out 2

00

Chem

orci

men

t 525

Chem

orfil

E

Chem

orgr

out 2

00 e

t

Chem

orcr

ete

WR

22

Chem

orpa

tch

66

Chem

oraz

E

Chem

oroc

Chem

oroc

HD

Chem

oroc

LT

Chem

orqu

artz

HB

D

Chem

orqu

artz

SLB

Chem

orqu

artz

TR

Chem

orfle

x 35

0

Chem

orre

c

Chem

orpa

rk II

I

Chem

orde

k

Chem

orcl

ad 9

000

Chem

orcl

ad 9

030

Chem

orcl

ad 9

100

Chem

orcl

ad 9

200

Chem

orcl

ad 9

600

Chem

orcl

ad 2

00

Chem

orcl

ad 2

00C

SL

Chem

orcl

ad 2

50

Chem

orcl

ad 3

00 S

L

Chem

orcl

ad 1

010

Chem

orcl

ad 2

020

Chem

orla

st

Adhesives & Binders







ACNORASTM


Chem

orbo

nd

Chem

orbo

nd 1

00

Chem

orcr

ete

WR

Chem

orse

t 100

G

Chem

orse

t 100

LV

Chem

orse

t 100

M

Chem

orse

t 400

SL/N

S

Chem

ordu

r 25

Chem

orse

al A

W 1

0

Chem

orse

al A

W 2

5

Chem

orse

al E

Chem

orse

al N

20

Chem

orse

al N

40

Chem

orse

al N

100

Chem

orse

al P

Chem

orgr

out 1

00

Chem

orgr

out 2

00

Chem

orci

men

t 525

Chem

orfil

E

Chem

orgr

out 2

00 e

t

Chem

orcr

ete

WR

22

Chem

orpa

tch

66

Chem

oraz

E

Chem

oroc

Chem

oroc

HD

Chem

oroc

LT

Chem

orqu

artz

HB

D

Chem

orqu

artz

SLB

Chem

orqu

artz

TR

Chem

orfle

x 35

0

Chem

orre

c

Chem

orpa

rk II

I

Chem

orde

k

Chem

orcl

ad 9

000

Chem

orcl

ad 9

030

Chem

orcl

ad 9

100

Chem

orcl

ad 9

200

Chem

orcl

ad 9

600

Chem

orcl

ad 2

00

Chem

orcl

ad 2

00C

SL

Chem

orcl

ad 2

50

Chem

orcl

ad 3

00 S

L

Chem

orcl

ad 1

010

Chem

orcl

ad 2

020

Chem

orla

st

Adhesives & Binders





7 Tri-Tex co inc.

CONSTRUCTIONc

PrimersProduct Generic Permeability /

steamWall Floor Substrate*

Chemorclad 9000 Epoxy Sealed yes yes 1-2-3-4-5



Chemorclad 9200 Epoxy Sealed yes yes 1-2-3

Chemorclad 9600 Epoxy Sealed yes yes 6-7

*Codes substrates :

1 = Concrete2 = Concrete block3 = Wood4 = Plywood5 = Gypsum6 = Ferrous Metals7 = Non-Ferrous Metals8 = Brick9 = Stucco

8 Tri-Tex co inc.

CONSTRUCTIONc

Application

Airl

ess

Stiff

bris

tle b

rush

Spon

ge

Caul

king

gun

s

Gra

vity

Pres

sure

inje

ctio

n

Text

urin

g m

achi

ne

Bru

sh

Shor

t-ha

ir br

ush

/ m

ohai

r

Gun

Proj

ectio

n

Spra

yer

Sque

egee

Not

ched

squ

eege

e

Roll

Spat

ula

Stee

l tro

wel

Woo

den

trow

el

Adhesives & BindersChemorbond • •Chemorbond 100 • • •Chemorcrete WR • •Chemorset 100 G •Chemorset 100 LV • • • •Chemorset 100 M • • • • •Chemorset 300 G • • • • • •Chemorset 400 5L N5 • •WaterproofingChemordek • •Chemorflex 350 •Chemormec •Chemorpark III • •

9 Tri-Tex co inc.

CONSTRUCTIONc

Application

Airl

ess

Stiff

bris

tle b

rush

Spon

ge

Caul

king

gun

s

Gra

vity

Pres

sure

inje

ctio

n

Text

urin

g m

achi

ne

Bru

sh

Shor

t-ha

ir br

ush

/ m

ohai

r

Gun

Proj

ectio

n

Spra

yer

Sque

egee

Not

ched

squ

eege

e

Roll

Spat

ula

Stee

l tro

wel

Woo

den

trow

el

MortarsChemorciment 525 •Chemorgrout 200 /Chemorcrete WR

• •Chemorpatch 66 •Chemorplug •Chemortop 423 •Primers & Coatings Chemorclad 150 • • •Chemorpclad 200 • • •Chemorclad 200 C SL • • •Chemorclad 250 • • •Chemorclad 300 SL • • •Chemorclad 1010 •Chemorclad 1012 • • •Chemorclad 2020 • •

• Studded roller

10 Tri-Tex co inc.

CONSTRUCTIONc

Application

Airl

ess

Stiff

bris

tle b

rush

Spon

ge

Caul

king

gun

s

Gra

vity

Pres

sure

inje

ctio

n

Text

urin

g m

achi

ne

Bru

sh

Shor

t-ha

ir br

ush

/ m

ohai

r

Gun

Proj

ectio

n

Spra

yer

Sque

egee

Not

ched

squ

eege

e

Roll

Spat

ula

Stee

l tro

wel

Woo

den

trow

el

Primers & Coatings (cont’d)Chemorclad 9000 • • •Chemorclad 9030 • • •Chemorclad 9100 • • •Chemorclad 9200 • • •Chemorclad 9600 • • • •Chemorlast • • • •SealersChemorseal AW 10 • •Chemorseal AW 25 • •Chemorseal E • •Chemorclseal N 20 • •Chemorseal N 40 • •Chemorseal P • •

11 Tri-Tex co inc.

CONSTRUCTIONc

Application

Airl

ess

Stiff

bris

tle b

rush

Spon

ge

Caul

king

gun

s

Gra

vity

Pres

sure

inje

ctio

n

Text

urin

g m

achi

ne

Bru

sh

Shor

t-ha

ir br

ush

/ m

ohai

r

Gun

Proj

ectio

n

Spra

yer

Sque

egee

Not

ched

squ

eege

e

Roll

Spat

ula

Stee

l tro

wel

Woo

den

trow

el

Seamless floorsChemorraz E •Chemorquartz HDB • •Chemorquartz SLB • •ChemorquartzTR • •MiscellaneousMetPrep • •

12 Tri-Tex co inc.

CONSTRUCTIONc

SprayProduct Sprayer ( Graco ) Nozzle ( Rac IV)

Chemorclad 51 King 45 : 1 221-521

Chemorclad 150 Monark 23: 1 221-517



Chemorclad 300 SL King 45 : 1 221-521

Chemorcald 1700 Monark 23: 1 221-517




Chemorcald 9100 Monark 23: 1 221-415


Chemorflex 350 King 45 : 1 221-627

Chemorlast 1 Texspray / E-11 0 C < 1/4”

Chemorlast Il Hopper Gun / E-11 0 C / Président 10 : 1 1/4 “

Chemorlast III Hopper Gun / E-11 0 C / Président 10 : 1 > 1/4”

Chemorseal E Monark 23: 1 221-411

Chemorseal N Monark 23: 1 221-411

Chemorseal P Monark 23: 1 221-411

Chemorseal 5 Monark 23: 1 221-411

13 Tri-Tex co inc.

CONSTRUCTIONc

CoatingsProduct Generic Number of

topcoatLayer thickness

Permeability /steam

Wall Floor Substrate*

Chemorclad 150 Epoxy 2 0,1 à 0,2 mm Waterproof yes yes 1-2-3-4-5-6-7-9

Chemorclad 200 Epoxy 1 à 2 0,25 à 0,5 mm Waterproof yes yes 1-2-3-4-5-6-7-9

Chemorclad 250 Epoxy 1 à 2 0,25 à 0,5 mm Waterproof no yes 5-6-7

Chemorclad 300 SL Epoxy 1 à 2 0,5 à 2,5 mm Waterproof yes yes 1

Chemorlast Latex 1 0,1 à 1 mm Permeable yes no 1-2-8-9

Chemorraz E Epoxy N / A 6,3 mm Waterproof no no 1-4

Chemordécor Epoxy N / A 3,15 à 6,3 mm Waterproof no yes 1-4

Chemoroc Epoxy N / A 3,15 à 6,3 mm Waterproof no yes 1-4

Chemorquartz Epoxy N / A -6,3 mm Waterproof no yes 1-4

Chemorseal P Polyurethane 2 50 microns Restricted no yes 1

*Codes substrates :

1 = Concrete2 = Concrete block3 = Wood4 = Plywood5 = Gypsum6 = Ferrous Metals7 = Non-Ferrous Metals8 = Brick9 = Stucco

14 Tri-Tex co inc.

CONSTRUCTIONc

MixMix only the quantity which can be used before the expiry of the pot-life.

Combine Parts A and B in the ratio indicated on thecontainers. Mix well, using a non-sparking low speed electric mixer, until a homogenous blend is achieved (2-4 mins.). Use at once.

ApplicationApply with a roller, low pressure or airless spray. On rough floors it is preferable to use spray application. Ensure goodpenetration of the adhesive in the pores of the concrete.

The applied product should be allowed to dry until it becomes tacky. This tacky stage lasts about 4 hours @ 21°C. Higher temperatures accelerate while lower temperatures prolong the setting.

The adhesive must not be allowed to loose its tackiness before placing the fresh concrete or mortar. If CHEMORBOND looses its tack, apply another thin coat.

Avoid all contamination while the surface is being treated. Traffic should be forbidden. If traffic is necessary, sprinkle dry stone chips onto the coated surface to provide a traffic path.

BinderCan be used for bonding polymer reinforced mortars, CHEMORTOP, providing time is allowed for the solvents to evaporate before placing the mortar (approx. 2 hrs. @ 21°C., 4 hrs. @ 10°C.).

ChemorbondDescriptionCHEMORBOND is a liquid 2-component epoxy adhesive which was specifically designed to parallel strength gain of fresh concrete or mortar.

Permanent flexural strength of the product eliminates bondfailures resulting from stress or impact.

Features and BenefitsExcellent adhesion to dry or wet concrete and mortar.Curing rate to parallel that of fresh concrete or mortar.Long pot life of the adhesive mix allowing ease of use.Physical properties superior to those of bonded materials.

UsesMain uses are in bonding fresh plastic concrete or mortar to hardened concrete or mortar.

Procedure

Surface preparationHardened concrete surface to be bonded must be clean and sound .

Smooth floors should be acid etched, rinsed and all surfacewater removed prior to the application of CHEMORBOND.

Soft or powdery concrete floors should be ground rather than acid etched.

Adhesives & Binders / Chemorbond

15 Tri-Tex co inc.

CONSTRUCTIONc

SafetyThe product in its liquid state is flammable.

Keep away from heat, open flame or sparks.

Use with adequate ventilation.

Avoid contact with the eyes and skin.

Wash with soap & water.

If an irritation results, see a physician.

Refer to the Material Safety Data Sheet.

Technical Data

AdhesionA5TM C-882type Il 12,7 MPa

Viscosity110 @ 130 MPa.s

Flash point:-6°C

Pot life@ 21°C for 60g 6 hours

Curing time@ 21°CInitial 24 hoursComplete 7 days

Coverage3.5-4.7m2/litredepending on the porosity of the surface.

PackagingThe CHEMORBOND is packed in metal containers.Depending on demand the weight of shipping units can vary between 8.4 kg and 42.3 kg in containers of 7.56 l. to 37.84 l.

Entreposage et durée de conservationDans son emballage d’origine, le Chemorbond peut êtreconservé pendant 1 an.

ColorPale amber

Clean-upClean all tools and equipment, with Chemor Solvent SV-40, while the product is still fresh. Once it has cured, removal will be very difficult.

Adhesives & Binders / Chemorbond

16 Tri-Tex co inc.

CONSTRUCTIONc

Technical Data

Solids content100%.

Presentation2-component product: Parts A and B.

ColorPale amber.

Pot life of the mix (21ºC): 40 mins.

Viscosity 400 ± 50 mPa.s.

Flash point>100°C.

Coverage3.5-4.7m2/litredepending on the porosity & roughness of the surface.

Curing time @ 21°Cinitial 24 hourscomplete 7 days

AdhesionASTM C-882,TYPE II 12.7 MPa

Cleaning solventChemor solvent SV-40.

Chemorbond 100DescriptionCHEMORBOND-100 is a two-component epoxy adhesive that cures at ambient temperature. Curing rate was specifically designed to parallel the strength gain offresh concrete or mortar.


Advantages100% solids; contains no flammable solvents.

Excellent adhesion to dry or wet concrete and mortar.

Curing rate to parallel that of fresh concrete or mortar.

Physical properties superior to those of bonded materials.

UsesBonding fresh plastic concrete or mortar to hardened concrete or mortar.

As a coating to protect reinforcing steel.

LimitationsA minimum ambient temperature of 8ºC must be maintained during the application and curing period.

NOTE: It is essential that the surface of CHEMORBOND-100 be still tacky at the time of placing the mortar.

Adhesives & Binders / Chemorbond 100

17 Tri-Tex co inc.

CONSTRUCTIONc


SafetyDo not breathe vapors.

Keep away from flame or sparks.

Use protective gloves and safety glasses.

Contact could cause dermatitis.

Protect eyes and skin.

In case of skin contact, wash with soap and water.

If irritation persists, consult physician.

Refer to «Material Safety Data Sheet» (MSSD).

Surface preparationHardened concrete surface to be bonded must be clean and sound .Smooth floors should be acid etched, rinsed and all surfacewater removed prior to the application of CHEMORBOND-100.


Directions for use

MixMix only the quantity which can be used before the expire of the pot-life.

Combine Parts A and B in the ratio indicated on thecontainers. Mix well, using a low speed non-sparking electric mixer, until a homogenous blend is achieved(2-4 mins.). Use at once.

ApplicationApply with a roller or airless spray. On rough floors it ispreferable to use spray application.

Ensure good penetration of the adhesive in the pores of theconcrete.


The adhesive must not be allowed to loose its tackiness before placing the fresh concrete or mortar. If CHEMORBOND-100 looses its tack, apply another thincoat.


Adhesives & Binders / Chemorbond 100

18 Tri-Tex co inc.

CONSTRUCTIONc

Technical Data

Presentationliquid emulsion.

Colormilky white.

Flammabilitynon-flammable.

Shelf lifeone year in original packaging if stored between 4ºC-30ºC.

Coverage of mortar at 6.25mmthickness : 1.82m2 per liter of CHEMORCRETE WR.

LimitationsBeing water based,must be kept from freezing.

Ambient,substrate and mix temperature must be at least 5°C. during application and for the following 48 hours.

Surface preparationSmooth,dense concrete must be roughened, mechanically or by chemical means, to a profile of at least 1.5mm.

The surface must be sound, clean and free from oils, grease, debris or any other contaminant which could impair good bonding.

Thoroughly soak the substrate prior to application of bonding grout,but remove any standing water.

Chemorcrete WRDescriptionCHEMORCRETE WR is an acrylic copolymer emulsion. It contains anti-foam agents to prevent entrainment of excess air.

Classified by the American Concrete Institute as a nonremulsifiable type.

AdvantagesImproves adhesion by a factor of 2 to 3 compared to conventional mixes.

Increases impact resistance.

Reduces cracking as a result of doubling tensile strength.Increases durability: greatly reduced water and deicing saltabsorption results in a high freeze-thaw resistance.

UsesInterior and exterior.

Admixture for bonding grouts for mortar and concrete used in levelling slabs, resurfacings, patching and filling.

Additive for stuccos, white or grey.

Admixture for masonry and mortars to restore waterproof joints.

Concrete slabs, columns, beams, retaining walls, reservoirs,bonding fresh to hardened concrete.

Adhesives & Binders / Chemorcrete WR

19 Tri-Tex co inc.

CONSTRUCTIONc

Keep mixing time to a minimum to prevent entraining too much air.The consistency of the bonding grout should be that of thickcream.

Placement

Bonding groutFor an optimum adhesion, bonding grout should be placed immediately after mixing and brushed-in with stiff-bristled broom. This assures good penetration of the grout intothe concrete. Do not exceed 3mm thickness.

SurfacingGrouted section should be topped immediately with mortar/concrete mix.

Never allow the grout to dry (loss of stickiness) when placing the topping. Strike off and immediately trowel mix. Avoid overfinishing which may cause water exudation, drying and cracking.CHEMORCRETE WR modified Portland cement mixes are more sticky, therefore more difficult to finish than conventional mixes.

CuringWet curing for three days assures optimum property development of the mortar. It is very important to prevent rapid drying of the mortar during this period.Do not use solvent containing curing membranes

CleaningClean tools with water, immediately after use.

SecurityProtect eyes and skin against alkalinity of cement and possible irritation by polymer.Wash with clean water.If irritation persists, consult physician immediately.Refer to Material Safety Data Sheet (MSDS).

Suggested mixes

bonding grout:

Ingredient Weight kg

Portland cement 1 bag 40 kg, 12,7l.

Dry sand (loose) 1 bag 40 kg, 14,5 l.

CHEMORCRETE WR Diluted with water 1 to 1 by volume

approx. 20 kg, 20 l.

Mortar:

Ingredient Weight kg

Portland cement 1 bag 40 kg, 12,7 l.

Dry sand (loose) 3 bag 120 kg, 43,6 l.



Concrete:

Ingrédients Weight kg

Portland cement 1 bag 40 kg, 12,7 l.

Dry sand (loose) 2,5 bag 100 kg, 36,3 l.

Stone aggregate (max.10mm) 80 kg, 31,9 l.



NOTE: Do not use air-entraining agents with CHEMORCRETE WR.

MixingWith mixer running, add materials in the following order:

1. CHEMORCRETE WR.2. Stone aggregate (if required).3. Sand.4. Cement.

Normal mixing time is 1 to 2 minutes. Fluidity can be adjusted by adding more CHEMORCRETE WRsolution.

Adhesives & Binders / Chemorcrete WR

20 Tri-Tex co inc.

CONSTRUCTIONc

Technical Data

Solids content 100%.


ColorPale amber.

Pot life of the mix (21ºC) 40 mins.


Flash point>100°C.

Coverage3.5-4.7m2/litredepending on the porosity & roughness of the surface.

Curing time @ 21°C.initial 24 hourscomplete 7 days

AdhesionASTM C-882,TYPE II 12.7 MPa

Cleaning solventChemor solvent SV-40.

Chemorset 100 GDescriptionCHEMORBOND-100 is a two-component epoxy adhesive that cures at ambient temperature. Curing rate was specifically designed to parallel the strength gain offresh concrete or mortar.


Advantages100% solids; contains no flammable solvents.

Excellent adhesion to dry or wet concrete and mortar.Curing rate to parallel that of fresh concrete or mortar.

Physical properties superior to those of bonded materials.

UsesBonding fresh plastic concrete or mortar to hardened concrete or mortar.

As a coating to protect reinforcing steel.

LimitationsA minimum ambient temperature of 8ºC must be maintained during the application and curing period.

NOTE: It is essential that the surface of CHEMORBOND-100 be still tacky at the time of placing the mortar.

Adhesives & Binders / Chemorset 100 G

21 Tri-Tex co inc.

CONSTRUCTIONc


SafetyDo not breathe vapors.Keep away from flame or sparks.Use protective gloves and safety glasses.Contact could cause dermatitis.Protect eyes and skin.In case of skin contact, wash with soap and water.If irritation persists, consult physician.Refer to «Material Safety Data Sheet» (MSSD).

Surface preparationHardened concrete surface to be bonded must be clean and sound .Smooth floors should be acid etched, rinsed and all surfacewater removed prior to the application of CHEMORBOND-100.


Directions for use

MixMix only the quantity which can be used before the expire of the pot-life.

Combine Parts A and B in the ratio indicated on thecontainers. Mix well, using a low speed non-sparking electric mixer, until a homogenous blend is achieved(2-4 mins.). Use at once.

ApplicationApply with a roller or airless spray. On rough floors it ispreferable to use spray application.

Ensure good penetration of the adhesive in the pores of theconcrete.


The adhesive must not be allowed to loose its tackiness before placing the fresh concrete or mortar. If CHEMORBOND-100 looses its tack, apply another thincoat.


Adhesives & Binders / Chemorset 100 G

22 Tri-Tex co inc.

CONSTRUCTIONc

Uses

As an adhesive:To consolidate cracked concrete, applied by pouring or pressure injection.

Bonding of anchor bolts.

As penetrating sealerApply with a squeegee or a roller to ensure that the concrete is completely saturated without leavingexcess material.

As a grout/mortarMix with dry silica sand to set anchors.Filling of cracks and cavities in concrete.Patching of concrete.Filling under base plates of bridges, machinery and equipment.

Technical Data

PresentationTwo-components Parts A and B

Viscosity of mix 450-550 mPa.s.@ 21°C

Pot Life of Mix (60gm mass.@ 21°) approx. 25 mins.

Curing Time (Thin film @ 21ºC)Set to touch 3 hours.Hard 4 hours.Complete Cure 3 days.

Cleaning SolventSV-40.

Storage LifeOne year in original unopened container@ 10-28°C.

Chemorset 100 LVDescriptionCHEMORSET 100 LV is a very fluid 2-component 100% solids epoxy adhesive/binder curing at ambient temperature.

As a result of the product’s low viscosity and good wetting ability it is ideal for filling of cracks and fissures in concrete by either gravity flow or pressure injection.

It is equally useful for adhering anchor bolts and steel reinforcing rods in concrete.

Can be used as is or mixed with calibrated dry silica sand to form a grout/mortar.

AdvantagesDeep penetration into cracks and fissures due to low viscosity and good wetting ability.

Moisture insensitive, permitting work under adverse conditions found on many work sites.

High mechanical properties combined with good flexibility.

LimitationsCuring time is accelerated by higher temperatures while it is prolonged by lower ones. Work should not be undertaken if the ambient or concrete temperature is below 5°C.Must not be used on surfaces containing ice or frost.

Never dilute Chemorset 100 LV with a solvent.

Adhesives & Binders / Chemorset 100 LV

23 Tri-Tex co inc.

CONSTRUCTIONc

Mix

AdhesiveOnly mix the quantities that can be used before the expiry of the pot life. Measure the materials carefully; add part B to part A.Agitate well with a mechanical mixer for 2-3 mins; ensure that the sides and bottom of the container are scraped.

Drout/MortarMix parts A and B and then add dry calibrated silica sand.Grout: Use approximately 2 volumes of sand to one volume of binder.Mortar: Use approximately 3-3.5 volumes of sand to one volume of binder.Granulometry of sandDry sand of size #30 is good for general use.

Application

AnchorsUse the binder as is for holes of a diameter up to 3mmlarger than the bolt. For larger holes use a grout or mortar.

Penetrating SealerApply by roller or squeegee.

Crack fillingFor gravity flow filling or pressure inject.

CleaningTools and equipment should be cleaned before the material sets.

Typical physical properties(binder cured 7 days @ 21ºC)

Compressive strengthASTM D-695 73 MPa

Tensile strengthASTM D-638 41 MPa

ElongationASTM D-638 4%.

Pull strength of anchorsBolt 225mm length x 35mm diameterin a hole 155mm deep x 50mm diameter >150 kN.

Bolt of 13mm diameter in a hole102mm deep x 19mm diameter 55 kN.

Directions for use

Surface preparationAll surfaces must be clean and sound, free of standing water.

Steel: Sandblast or wire brush.Concrete: Roughened mechanically or chemically.Wood: Sanded.

Adhesives & Binders / Chemorset 100 LV

24 Tri-Tex co inc.

CONSTRUCTIONc

Uses

As an adhesiveAdhesive for bonding fresh or hardened concrete or mortar to cured concrete.

Adhesive for bonding polymer reinforced mortars (CHEMORTOP 411, 421, 422, 423) to cured concrete.

Embedding anchor bolts.

Filling cracks.

Gluing concrete masonry, stone, wood, metal to themselves or each other.

As a grout-mortarEmbedding anchor bolts.

Filling cracks or cavities in concrete.

Grouting of bridge and machine base plates.

Patching concrete.

Technical Data (BINDER)

PresentationTwo component liquid Parts A and B.

ColorAmber.

Typical mixed viscosity @ 25ºC approx. 900 mPa.s.

Pot life of A/B @ 21ºC (mass 60gms) 15 minutes.

Curing time @ 21ºC (thin film)Dry to touch 2 hours.Hard 4 hours.Full cure 3 days.

Chemorset 100 MDescriptionCHEMORSET 100 M is a 2-component 100% solids adhesive epoxy binder of medium fluidity, curing at ambient temperature.

It is unusually versatile, high strength, insensitive to humidity for curing and adhesion.

Used neat, it bonds fresh to hardened concrete, hardened to hardened concrete, fills cracks, seals concrete, grouts anchors.

Mixed with calibrated, dry silica sand, it produces a structural grout/mortar for concrete repairs, grouting of anchor, bridge, equipment, and machine plates.

AdvantagesOne product for multiple uses; minimises mistakes, simplifies inventories.

High mechanical strength produces a structural adhesive, grout or mortar.

Moisture insensitive; facilitates work on building site.Cures at low temperatures (down to 5°C).

LimitationsHigh temperatures accelerate and low temperatures prolong curing time.

For this reason application is to be discouraged when the ambient or surface temperature is below 5°C.

Must not be used when ice forms on the surfaces to be bonded.

Adhesives & Binders / Chemorset 100 M

25 Tri-Tex co inc.

CONSTRUCTIONc

Adhesion to concreteAASHTOT 2372,5 MPa100% break in concrete

Typical physical properties.(binder cured 7 days @ 21ºC)

Compressive strength(ASTM D-695) 68 MPa.

Tensile strength(ASTM D-638) 27 MPa.

Elongation at break(ASTM D-638) 5%.

Bond strength (ASTM C-882)Type 1 2 days 11,4 MPa 14 days 13,8 MPaType 2 14 days 12,7 MPa

Anchor rod pull-out strengthAnchor rod 225mm long x 35mmdiameter in embedded in a hole 155mmdeep x 50mm diameter

>150 kN.

Surface preparationAll surfaces must be sound, clean and free of standing water and all other contaminants to ensure goodadhesion.

Steel Sand blast or steel wire brush.Concrete Mechanical abrading or acid etch (muriatic acid 12-15%).Wood Sand and remove dust.Stone Roughen and remove dust.

Coverage

Binderaverage of 3.9m2/l yields 0.25mm thickness on a smoothsurface.

Shelf lifeone year in original unopened container at 10-30°C.

CleanerChemor Solvent SV-40.

Typical physical properties of the mortar

Compressive strengthASTMC 109All ingredients were preconditioned to the test temperatures.Volume ratio of aggregate/binder: 2.25/1 (using CHEMORPATCH 66 aggregate).

5°C 22°C 32°C

3h 28 MPa

4h 37 MPa

5h 56 MPa 57 MPa

6h 59 MPa

7h 65 MPa

8h 27 MPa 64 MPa

10h 31 MPa

14h 43 MPa

24h 76 MPa 84 MPa

3 days 75 MPa 105 MPa


Ready for traffic 8 hours 4 hours 3 hours

Complete hardening

72 hours 24 hours 24 hours


26 Tri-Tex co inc.

CONSTRUCTIONc

CleaningTools must be cleaned before the product cures.

SafetyLiquid product is combustible.

Keep away from flame and sparks.



Do not breathe vapors.

Wash with soap and water.


Refer to «Material Safety Data Sheet» (MSDS).

Direction for useNever dilute with solvent.

Mix

BinderMix only the quantity that can be used before the pot life expires.

Measure the materials accurately: add Part B to Part A.

Mix thoroughly using a mechanical mixer, scrape sides and bottom of the container; mix for 2-3 minutes.

GroutTo the premixed binder (A+B),add approximately an equal volume of #40 mesh sand and mix well together.

MortarTo one volume of premixed binder (A+B), add 3.5 to 4 volumes of dry sand of desired mesh size.

For deeper filling crushed stone can be added. The diameter of the stone should not exceed one-half ofthe depth to be filled.

Application

Binder By gravity, spray, brush or squeegee.

Grout Squeegee.

Mortar Trowel.

For bonding fresh concrete or mortar the adhesive coat must be still tacky. If not , reapply a thin coat.


27 Tri-Tex co inc.

CONSTRUCTIONc

LimitationsCHEMORSET 400 should never be diluted with solvents.

Concrete should be at least 28 days of age.

After cure products form vapor barrier: should not be usedwhen hydrostatic pressure is anticipated.

Not to be used in expansion joints.

Not for continuous immersion service.

Minimum substrate temperature of 4°C,and preferably increasing during the curing process.

For best results, store products between 17°C and 30°C.

Estimating dataEach unit of CHEMORSET 400 will produce approximately the following joint length in lineal metres for joints dimensions as follows:

DEPTH WIDTH WIDTH DEPTH WIDTH WIDTH

3mm 6mm 1/8’’ 1/4’’

25 mm 49 24 1” 161 78

32 mm 40 19 1 1/4” 130 63

38 mm 33 16 1 1/2” 109 53

44 mm 28 13 1 3/4” 93 45

51 mm 25 12 2” 80 39

NOTE: these yields are based on complete depth fillings ofsaw cuts.

Chemorset 400 SL/NSDescriptionCHEMORSET 400 is a 2-component, solventless, epoxy-urethane copolymer. It forms a flexible, resilient, filler for filling cracks or cavities on horizontal, vertical and overhead surfaces, as well as static control or construction joints.

TypesAvailable in two consistencies depending on the job configuration.

TYPE SLSelf-levelling for horizontal use.

TYPE NSNon-sagging for vertical and overhead use.

AdvantagesTwo consistencies: Multi-purpose use.

Moisture insensitive.

Premeasured units for easy mixing.

Easy to apply.

No priming: direct bonding.

Permanently flexible: shock absorbing.

Resists wheel traffic and heavy loads.

UsesFilling horizontal, vertical and overhead cracks or cavities.Filling static control or construction joints.

Adhesives & Binders / Chemorset 400 SL/NS

28 Tri-Tex co inc.

CONSTRUCTIONc

Bond Strength ASTM C-882

2 days dry cure 7.5 MPa 7.6 MPa

14 days moist cure 4.0 MPa 4.9 MPa

Surface preparationConcrete must be sound and clean.Mechanically remove all contaminants such as: curing membranes, grease, oil, laitance, etc. Substrate may be dry (best adhesion) or «saturated surface dry».

Application

NOTE: Vertical SurfacesFor larger cavities addition of «Additif «T» to Chemorset 400 NS prevents slumping: Mix one litre of «Additif T» with 3.5 l unit of premixed Parts A & B of Chemorset 400 NS.

MixingStir both components separately prior to mixing them together.Add Part B to Part A container (sufficient space is provided)and mix mechanically at low speed to avoid air entrapment.

PlacingOn horizontal surfaces pour by gravity or inject CHEMORSET 400 SL with a caulking gun or by other method while maintaining,a steady pressure.Allow to cure fully before applying loads (3 to 7 daysdepending on temperature).

On vertical or overhead surfaces inject CHEMORSET 400 NS with a caulking gun or by other method while maintaining a steady pressure.

SecurityPrevent contact with eyes and skin.Do not breathe product vapors.If irritation occurs, consult physician immediately. Wash with soapy water. Use with adequate ventilation.See Material Safety Data Sheet.

Technical Data

400 SL 400 NS

Presentation 2-component products

Solids content (by weight)

100% 100%

Color Cement Grey C-4324

Mix Ratio (by volume) 6 parts Component A to 1 part Component B

Consistency Self-Levelling Non-sagging

Pot Life of mix (100g mass @ 23°C)

40 minutes

Curing Time (@ 23°C) Light trafic

24 hours

Curing Time (@ 23°C) Complete cure

7 days

Coverage 3.5 l unit fills 0.0035m3. Or 15.3m of joints 6mm wide by 38mm deep

Shelf Life One year in original unopened containers

Cleaner CHEMOR SOLVENT SV-40

Packaging 3.5 litre units :Part A :3 litres; Part B: 0.5 litre

Typical physical properties

PROPERTY TEST METHOD 400 SL 400 NS

Tensile strength (14 days)

ASTM D-638 4.4 MPa 4.9 MPa

Tensile elongation at break (14 days)

ASTM D-638 150% 150%

Tear strength (14 days)

ASTM D-624 30kN/m 30kN/m

Hardness (Shore A,14 days)

ASTM D-2240 75-85 75-85

Adhesives & Binders / Chemorset 400 SL/NS

29 Tri-Tex co inc.

CONSTRUCTIONc

LimitationsNever dilute the product: solvents impair proper curing.For best results do not use below 10°C.

Cured product should not be exposed to continuous service above 80°C (dry) and 55°C (wet).

Concrete must not be frozen at the time of application.Penetration will be reduced and as a resultadhesion will be reduced.

Technical Data

Presentation3-component product:Part A resin.Part B hardener.Part C aggregate.

Color cement grey

Pot life one hour. (mass 500g @ 22ºC)

Curing time (@ 22ºC)Initial 7 hours.Final 7 days.

Shelf lifemin. one year in unopened sealed containers.

Storagedry location @ 18ºC - 28ºC.

CleanerChemor solvent SV-40.

Chemorgrout 100DescriptionCHEMORGROUT 100 is a 3-component epoxy grout which cures rapidly at ambient temperature to develop excellent early strength characteristics.

This product was designed for work requiring very rapid setting combined with high resistance to compression,impact and vibration.

Three components :liquid epoxy resin (Part A) and its hardener, (Part B) along with carefully graded aggregate (Part C).

AdvantagesProduct is 100% solids.

Insensitive to moisture before application and after curing.

Early strength.

Resistance to impact and vibration.

Resistance to freeze/thaw cycling.

Very high electrical resistivity.

Excellent chemical resistance.

UsesPreparing bases for columns, machinery and heavy equipment, such as: motors, compressors, pumps, generators, etc.

That are used in petroleum, cement, pulp andpaper, metalurgical and chemical industries.

Anchoring, bolts, rails, base plates, equipment. Structural supports: columns, bridge seats.Wherever an electrical insulator is required.

Grouts / Chemorgrout 100

30 Tri-Tex co inc.

CONSTRUCTIONc

Tensile strengthASTMC 1907 days @ 22° C 16 MPa

Flexural strengthASTM C 2937 days @ 22° C 35 MPa

Bond to concreteASTM C 8827 days 22°C rupture in concrete.

Coefficient of lineal retreatASTMC5317 days @ 22° C 0,0006 mm/mm

Coefficient of thermal expansionASTMC5317 days @ 22° C 0,000037 mm/mm/°C

Water absorptionASTM07507 days @ 22° C 0,11%

Anchor pull-out strengthBolt 225mm long x 25mm diameter in a hole 155mm deep x 50mm diameter 150 kN (rupture in concrete)

Bolt 13mm diameter in a hole 102mm deep x 19mm diameter 55 kN

Electrical resistivityASTM 0257, UTE C 26-215under 10 000 volts 1 5x106MW.cm

Specific gravity2.26

Density2265 kg/m3.

PackagingStandard kit consists of a 18.9 L pail containing epoxy binder:

Part A (resin) 4.2 kg (3.8L)Part B (hardener) 1.9 kg (1.9L)Part C (aggregate) 2 bags @ 18kg each : 38kg.

Kit net weight 42.1 kg.

Yield

GroutComplete binder (A+B): 5.7 LApprox.1 bag (18kg) aggregate: 7.6 L

Total volume: 13.3 L (0.0133m³ or 0.47ft³)

MortarComplete binder (A+B): 5.7 L2 bags (36kg) aggregate: 15.2 L

Total volume: 20.9 L (0.0209m³ or 0.75ft³).

Physical properties (typical)(7 days cure @ 22ºC)

Compressive strengthASTM C 109

22°C 10°C

24 hours 79 MPa 57 MPa




31 Tri-Tex co inc.

CONSTRUCTIONc

Smaller quantities can be mixed, but ensure that the ratios of the three ingredients are respected.

Placement and finishingUse clean and dry stainless steel trowels. Avoid any possible contamination with foreign matter (e.g.paste wax used for release on form surfaces). Forms must be leak free. Smoothly trowelled grout surface does not require anyprotection. Allow to cure

Clean-upClean the tools immediately after use with Chemor solvent SV-40.

Hardened product is extremely difficult to remove.

SafetyContact could cause dermatitis.

If irritation persits, consult a doctor.



Ensure adequate ventilation.



Refer to «Materials Safety Data Sheet» (MSSD).

Résistance chimiqueASTM D 1308covered 7 days

Reactive ResultMotor oil,aliphatic and aromatic hydrocarbons.Diluted mineral acids and salts.Diluted organic acids. Alkalies. Unaffected

NOTE: for specific information consult Chemor technical service.

Surface preparation

ConcreteMust be sound and clean.Free from grease,oil, laitance, rust or any other contaminantwhich may impair good adhesion.

Steel Derust, then clean with METPREP. For maximum corrosion protection prime with CHEMORCLAD 9500.

Directions for useNOTE: Never dilute the product with solvent. Consistency can be varied by altering the amount of aggregate added to mix of A and B liquid.

MixPart A (resin) and B (hardener) using a low speed paddle mixer for about 3 minutes.

Under agitation slowly add Part C/ aggregate to desired consistency .

Continue to mix for approximately 10 minutes.

Mixed material must be placed within 60 minutes. Discard any mixed grout which has not been placed within this time.


32 Tri-Tex co inc.

CONSTRUCTIONc

Yield Each 25kg bag gives approximately13L (0.013m3) of liquid grout.

Initial setApproximately 2½ hours.

Final setApproximately 4 hours.

ShrinkageNone

Expansion at hardeningless than 0.4% following CRD-C589-7.

Freeze-thaw resistance(ASTM 666) Excellent.

Service temperature0-175°C.

Packaging25 kgs moisture proof bags.

Storage lifeone year in original unopened container, stored in a dry place.For best results store between 15-25°C.

Consistency Water/Bag 25kgDry 3,5 l.Plastic 3,9 l.Flowable 4,25 l.

Chemorgrout 200DescriptionCHEMORGROUT 200 is a premixed, ready to use cement grout containing a blend of specially selected and proportioned fillers. Just add water.

This product is exceptional because of its fast set,initial andcontrolled gaseous expansion which counteracts shrinkage due to segregation and drying.

Also it contains no metallic or corrosive additives (eg.calcium chloride).

AdvantagesThe product is scientifically balanced, proportioned and premixed under strict quality control.

Various consistencies are available to fit the particular job;just vary the quantity of added water (see «Directions for use»).-Dry-Plastic-Flowable-Non-corrosive.-Non-metallic (non staining).-High compressive strength.

UsesThe product is used to construct the base plates for heavy machinery, footing of framework columns; cementing sealing plates, anchorage bolts, foundations andunderpinnings; filling and patching concrete.

Technical Data

Packaging Cement-grey powder in multiple layer paper bags laminatedwith polyethylene for maximum resistance to humidity.


33 Tri-Tex co inc.

CONSTRUCTIONc

Mixed grout that has not been used after one hour should be discarded.

CuringThe applied grout must be damp cured (wet tarpaulin) for 24-36 hours, then a liquid curing membrane can be applied over the surface.

SafetyAvoid contact with the skin and eyes(alkalinity of cement).

Clean tools with water while the grout is still fresh.

Refer to Material Safety Data Sheet.

LimitationsThis grout must not be exposed to freezing while curing.

Surface preparationThe surface must be clean, damp, free of oil, grease, laitance, dust and all other contaminants.

It is recommended to roughen the surface for best adhesion.

In special cases, or if there is any doubt, seriously consider using a bonding agent, such as CHEMORCRETE SB/emulsion type, or CHEMORBOND epoxy type.

If the use of an adhesive is not considered, saturate the surface with water for 24 hours before applying the grout.

All standing water must be removed before application.

Position and anchor all pieces where the grout will be used.

Forms for retaining the grout under the base plates must besolid and impervious in order to prevent any leaking.

Mixing and placingNOTE: For deeper fillings CHEMORGROUT 200 can be mixed with up to 50% of washed aggregate of up to 10mm size.

A mechanical concrete or mortar mixer is recommended for preparing the grout.

Depending on the consistency required, put between 3.5 and 4.25 litres of water in the mixer and slowly add under agitation the contents of a 25 kg bag of the product.

Continue mixing for at least three minutes.

Any of the mixed grout that is not immediately placed should continue to be mixed until used.

Mix only the quantity of grout that can be used in 30 minutes.


34 Tri-Tex co inc.

CONSTRUCTIONc

Advantages• Wear resistant,durable,seamless.• Bonds tenaciously to properly prepared substrates.• Impact resistant.• Elastomeric waterproof membrane chemically welded

to wear resistant surfacing.• Type II offers decorative motifs.• Rapid installation.• Easy maintenance.

UsesNew work or maintenance.

Balconies, patios, exterior terraces, elevated walkways,swimming pool decks, roofs permitting traffic.

LimitationsNew concrete must have been water cured and at least 28 days old.

The humidity in the concrete to be coated should not exceed 15%.

Surfaces to be coated should be sound, clean, smooth, dry and free of all material which could impair good adhesion.

Surface temperature should be a minimum of 15.

CHEMORDEK should be protected from rain for 24 hours following application.

Typical technical properties

CHEMORFLEX 350 See technical data sheet «WATERPROOFING» section

TYPE I/CHEMORCLAD 2020 IISee technical data sheet/»COATINGS» section

TYPE II/CHEMORQUARTZ SLBSee technical data sheet/ «SEAMLESS FLOORING» section.

ChemordekDescriptionCHEMORDEK is a liquid applied waterproofing elastomeric coating system which follows the contours of the surfaces to which it is applied.

The system cures at ambient temperature, providing ananti-skid wear surface that is protective, decorative andseamless.

TYPESTwo types are available depending on the requirements for wear resistance.The two types use the waterproof elastomeric membrane «CHEMORFLEX 350» grey. They differ in the wear coats used.

TYPE I :An economical system of medium thickness, 0.9mm, with a solid color wear coat of «CHEMORCLAD 2020 II».

TYPE II:An ultra-durable, decorative aggregate broadcast systemCHEMORQUARTZ SLB. Solid or blended colors.High build: 1.5mm for single broadcast 3mm for doublebroadcast, depending on traffic intensity.

ColorsTYPE I: solids colors as shown on CHEMOR polyurethane color selector.

TYPE II: see CHEMORQUARTZ SLB, patterns selector. Other patterns are available on demand.

Waterproofing / Chemordek

35 Tri-Tex co inc.

CONSTRUCTIONc

Installation procedureNOTE:Humidity of the concrete should not exceed 15%.Prior to use, condition the materials to a temperature of18-26°C.A temperature of at least 15°C is required for application and curing. Lower temperatures prolong curing time.

ProductsWaterproofing elastomeric membrane:: CHEMORFLEX 350.

Wear coat: the type and color should be specified :TYPE I : CHEMORCLAD 2020 IITYPE II: CHEMORQUARTZ SLB.

Surface preparationRemove all sealers or paints on the surface.

The surface should be roughened by chemical or mechanical means to assure good adhesion.

Remove dust.

The concrete must be dry: humidity of the concrete should be 15% maximum.

RepairsNOTE: Active cracks should be laminated with fiber glass tapeand CHEMORFLEX 350.

Fine cracks, up to 2mm in width should be masticated withCHEMORFLEX 350.

Cracks 2mm and over in width should be saw cut and filled with CHEMORSET 400 NS.

Deep cracks should be injected with epoxy CHEMORSET 100LV, by gravity or under pressure.

For levelling or making slopes use CHEMORFIL «E» epoxy grout/ mortar.

Typical characteristics

Characteristic Elastomeric membrane

Wear coat

Chemorflex 350 grey

Type IChemorclad 2020 II

Type IIChemorquartz SLB

Presentation Two-components products

Thickness, total dry

0.75mm 0.9mm 1.5 - 3mm

Application method

Brush, roller, notchedsqueegee, spray

Brush, roller,spray

RollerBroadcastaggregate

Number of coats

One Two Matrix : one or two

Top coat: one

Curing time: (@ 21°C & 50% R.H.)

Initial 16 hours

Complete 7 days

Storage life(18°- 20°C)unopened originalcontainer

1 year


36 Tri-Tex co inc.

CONSTRUCTIONc

TYPE IICHEMORQUARTZ SLBOnly an applicator approved by the manufacturer is authorised to install this system.

Specify the pattern and the thickness: 1.5mm for singlebroadcast or 3mm for double broadcast.

This coating is prepared on the jobsite with a clear epoxy binder and colored aggregates.

CHEMORCLAD 2020 I, clear aliphatic polyurethane, is thefinish.

MaintenanceWash with water with or without a non-abrasive detergent.

SafetyDo not breathe vapors of the products.


Avoid all contact with eyes and skin.

Wash with soapy water.

In case of irritation, immediately seek medical assistance.


ApplicationNotice: Curing times of all the materials involved are accelerated by higher temperatures, surface or air temperatures.

It is recommended to start operations in the shade.

Application of the second coat should commence as soon as the first coat is no longer tacky.

Depending on temperatures, this could be as early as 30 minutes.

CHEMORFLEX 350 / Elastomeric membraneUnder agitation, add Part B (hardener) to Part A(resin), inthe ratio indicated on the container.

Continue mixing until the material is homogeneous.

Apply the mix with a notched squeegee or by spray to a wet film thickness of at least 0.75mm.

Roll back to ensure complete wetting of the surface.

Allow to cure just until the surface is no longer tacky and proceed with the following application.

TYPE ICHEMORCLAD 2020 II / Solid colorUnder agitation add Part B (hardener) to Part A (resin) inthe ratio indicated on the container.

Continue mixing until the material is homogeneous.

Apply the first coat with a short nap roller to a wet film thickness of 0.15mm (coverage 6.5m²/L).

After the first coat has lost its tackiness, apply a second coat at the same thickness.

While the second coat is still fresh, lightly broadcast #40silica sand over the surface and roll back. Allow the system to fully harden before permitting traffic.


37 Tri-Tex co inc.

CONSTRUCTIONc

LimitationsCHEMORFLEX 350 should be protected by a finish coating.

Substrates should be sound, clean and dry, at a temperature above 10ºC.

NOTE: lower temperatures delay whereas higher ones accelerate curing times.

Technical Data

Adhesion (AASHTO T 237-73)100% concrete rupture

Tensile strength 7 MPa(ASTM D-412)

Elongation 350 %(ASTM D-412)

Tear resistance 22 kN/m(ASTM D-624)

Hardness (SHORE A) 60-70(ASTM D-2240)

Abrasion resistance 0.015g(ASTM D-4060)(Taber,wheel CS-17, 1000 weight,1000 cycles)

Permeability 6.9ng/Pa.s.m²(ASTM E-96)

Water absorption 0.8%(ASTM D-570)

Chemorflex 350DescriptionCHEMORFLEX 350 is a liquid solventless, elastomeric membrane based on a 2-component polyurethane/epoxy copolymer.

The membrane cures by polymerization at ambient temperature.

CHEMORFLEX 350 liquid membrane combines the outstanding and complementary properties of itsconstituent polymers: elasticity of the polyurethane combined with adhesion and toughness of the epoxy.

TypesTwo types are available:350 H for horizontal surfaces.350 V for vertical surfaces

Advantages• Free from volatile, flammable solvents.• Continuous waterproof bond on application to various

substrates.• Permanent elasticity: unaffected by aging, allowing it to

bridge over small cracks.• Lends itself to overlaying with a variety of decorative

architectural finishes and wear courses for vehicular traffic.

• Easily repairable.

UsesCHEMORFLEX 350 is designed to waterproof parking decks, floors, walls, bridge decks, terraces, planters, pools, etc. which are not subjected to hydrostatic pressure.

Used between concrete slabs, under Chemor special floor or wall finishes, ceramic tile, stone slabs, etc.

Waterproofing / Chemorflex 350

38 Tri-Tex co inc.

CONSTRUCTIONc

Surface preparation

NOTEConcrete floor levellingUse of Chemorfil «E» self-levelling epoxy grout or Chemortop polymer modified cement is recommended.

For construction joints and cracks use Chemorset 400NS/SL.

ConcreteRoughen by mechanical or chemical means.

At the time of application, maximum moisture content in concrete should not exceed 15%.

Surface must be sound, clean, dry, free from any contaminant such as grease, oil, laitance, concrete curingmembrane, paint, sealer, etc.

ApplicationRoller, or notched squeegee.

Stir separately Parts A & B prior to proportioning them.

Under agitation, add Part B (hardener) to Part A (resin) in the ratio indicated on the package.

Apply to the specified film thickness.

NOTE: For thicker consistence “Additif T” can be added to the mix with mechanical stirring.

For interior applications, at normal temperatures of 15-23°C., allow membrane to cure a maximum of 24 hoursbefore applying the wear course.

At higher temperatures and for exterior applications, apply the wear course as soon as the membrane becomes tack free.

Chemical resistance(ASTM C-957)

Water excellentEthylene glycol (anti-freeze) excellentMineral spirits very goodDetergent @ 7 % excellentHydraulic fluid very goodMotor oil excellentDeicing salts excellent

Product data

Presentation2-component product (Parts A and B).

Color grey

Solids content 100%


Pot life 60-80 minutes.(100mL mix @ 21ºC)

Crack bridgingAt application rate of 1.33m²/L (0.75mm dry film thickness) will bridge up to 1.6mm wide cracks.

Number of coats minimum one.

Curing time(@ 21°C. and 50% R.H.)initial 16 hoursfinal 3 days

CleanerChemor Solvent SV-17.

Shelf life one year in original unopened containers at 15-26°C.


39 Tri-Tex co inc.

CONSTRUCTIONc

Longer curing times of the membrane could impair the adhesion of the wear course. If recommended curing timesor temperatures are exceeded, it will be necessary to depolish the surface by scuff-sanding.

In case of cementitious overlays, allow 72 hoursprior curing.


Work area should be well ventilated.

Protect skin and eyes from contact with liquid product.

If irritation persist call for medical assistance.

Refer to «Materials Safety Data Sheet» (MSDS).


40 Tri-Tex co inc.

CONSTRUCTIONc

AdvantagesTenacious adhesion to well prepared concrete floors.

Durable waterproofing membrane.

Capable of bridging fine cracks in concrete.

Thin, light weight coating.

Excellent resistance to wear, impact and common chemicals.

Easy to repair.

Uses

InteriorsTo assure waterproofing of concrete floors subject to pedestrian and light vehicular traffic:mechanical rooms, laundries, laboratories, etc.

LimitationsNew concrete must be water cured, at least 28 days.

The surfaces to be coated must be sound, smooth, clean, free of curing membrane and dry and at a temperature of at least 15°C.

If repair or restoration of the floors is required, consult Chemor for recommendations on materials compatible with the CHEMORMEC system.

ChemormecDescriptionCHEMORMEC is a system comprising a waterproofing membrane followed by an anti-skid coating for useon mechanical room floors.

CHEMORMEC, applied in the liquid state,provides a continuous waterproofing membrane for concrete.

The system cures rapidly by polymerization.

CHEMORMEC consists of two materials which do not require prepriming of the concrete.

1. Elastomeric membrane CHEMORFLEX 350Is a polyurethane/epoxy copolymer which incorporates the superior properties of both polymers.

The elasticity of the polyurethane is combined with the adhesion and exceptional toughness of the epoxy.

2. Anti-skid finish CHEMORCLAD 150 or CHEMORCLAD 200CHEMORCLAD 200 being solventless, 100% solids coating is applied in a single coat (see Table: Typical characteristics) compared to two coats of CHEMORCLAD 150.

These flexibilized epoxy based coatings are designed to be compatible with the elastomeric membrane while at the same time providing a tough matrix for the incorporated granules.

colorsChemor grey C-4195 is the standard color for the finish CHEMORCLAD 150 or CHEMORCLAD 200.

Other colors are available on demand.

Waterproofing / Chemormec

41 Tri-Tex co inc.

CONSTRUCTIONc

Directions for use

Application of membraneCHEMORFLEX 350Under agitation, add Part B (hardener) to Part A (resin) inthe ratio indicated on the package.

Once the mixture is homogenous, pour it on the floorand spread it evenly with a notched squeegee calibrated togive a minimum wet thickness of 0.60mm., corresponding to a coverage of 1.97m²/L.

Back-roll the membrane to assure uniform thickness and complete coverage of the surface.

For interior applications, at normal temperatures of 15-23°C., allow membrane to cure a maximum of 24 hours before applying the wear course.

At higher temperatures and for exterior applications,apply the wear course as soon as the membrane becomes tack free.

Longer curing times of the membrane could impair the adhesion of the wear course.

If recommended curing times or temperatures are exceeded, it will be necessary to activate thesurface of the membrane with Chemor activator SV-42.

Application of finish coatsCHEMORCLAD 200Under agitation, add Part B (hardener) to Part A (resin) inthe ratio indicated on the package.

Apply the mix uniformly to the specified thickness.

For a single coat application (CHEMORCLAD 200) broadcast #24 silica sand over the surface to provide an anti-skid finish.

ApplicationNOTE:• Humidity of the concrete should not exceed 15%.• Prior to use, condition the materials to a temperature of

18- 26°C.• A temperature of at least 15°C is required for

application and curing.Lower temperatures prolong curing time.

• For maximum waterproofing, the system should be applied up to a height of 10 cm. at joints of floor -wall and floor-columns.

Surface preparation

New concrete Relatively smooth surface.

Wet curing should be provided (liquid curing membraneswill detract from adhesion).

New or aged concreteMeticulous cleaning is required to removeall contaminants (eg. laitance, grease, oil, paint, etc.) anddefective concrete.

Preparation of the surface can be by mechanical or chemical means.

Rinse with water under pressure to remove all debris and residues and let dry.

To restore the surface, masticate cracks and fill cavities consult a Chemor representative.

Generally, cracks and construction joints should be covered in advance with a coat of membrane 0.50mm thick and 150mm wide.


42 Tri-Tex co inc.

CONSTRUCTIONc

AdhesionAASHTOT 237 2,7 MPa 100 % concrete rupture Abrasion resistanceASTM D 40601000 cycles, wheel CS17Weight 1000 g 50 mg loss

Leaching1 GP 71; 125,1 pass 10 000 cycles

Water absorptionASTM D 570 0,2 %

Transmission of water vaporASTM E 96 6,9 ng/pa.s.m2

Shock resistance1-GP-71;147.1 15 OJ minimum. rectoHardnessASTM D 2240 shore D 85

Thermal Resistance85 °C peak

FlammabilityASTM D 635 Self-extinguishing

ToxicitéAgriculture Canada accepted Viscosity A + BApprox. 1100 mPa.s, depends on the color. Flash point21 ,1 °C

Back-roll to ensure a uniform thickness. Allow two days curing before opening to traffic.

For a second coat application (CHEMORCLAD 200), apply within 24 to 48 hours after the first one and follow above procedure for silica sand incorporation.

Technical Data(for Chemorflex 350 see page 37)

Chemorclad 200

Tensile strenghtASTM D 638 45 MPa

Rupture strengthASTM D 638 3%mlnlmum

Chemical ResistanceASTM 1308 Covered 7 days

Reactive Result

Detergent solution(5% Ajax), sodium chloride 20%, sodium chloride 20%,20% ammonia, baking soda 20%, trisodium phosphate 20%, caustic soda 20%, bleach to 3%, mineral spirits, methanol, Mullein, xylenes, hydrochloric acid 10%, citric acid 10%, lactic acid 5% unleaded gasoline, coffee, tea, beer, urine, Skydrol.

Untouched

Chromic acid 20% Loss of gloss, stains, softened

Nitric acid 10% Some yellowing

Sulfuric acid 10 % Slight discoloration


43 Tri-Tex co inc.

CONSTRUCTIONc

Pot life@ 21 °C for l00g 1 hour

Curing time@ 21 °CDry to touch 4 hoursReady to covered 8 hoursReady for traffic:pedestrian 8 hoursvehicular 16 hours

YieldThe yield of Chemorflex 350 1,97 m2/ l.The yield of Chemorclad 200 7,9 m2/ l.

MaintenanceWash with water with or without a non-abrasive detergent.

SafetyUse with adequate ventilation.

Do not breath vapors.

Avoid contact with eyes and skin.

Skin contact could cause dermatitis.

Wear safety glasses, protective gloves & clothing.



44 Tri-Tex co inc.

CONSTRUCTIONc

ColorsCHEMORPARK is available in standard grey.

Black is available on request.

AggregatesProvide additional wear resistance and non-skid properties to the wear course.

They must be of angular shape and of minimum hardness 6.5 on the Mohs scale.

Their size depends on the requirements of a specific area: (parking stalls, driving lanes, ramps, turns: see Table III).

Advantages• Free from any volatile, flammable solvents.• Tenacious adhesion properties.• Waterproof and durable.• Crack-bridging capability.• Low thickness and light weight.• Excellent abrasion and wear resistance.• Increased traction on non-skid wear course.• Positive and durable slab protection against corrosive

intrusions of water and deicing salts.• Easy to repair.

UsesProtection of parking deck structures, above and below grade.

LimitationsNew concrete must be water-cured and at least 28 days old. It has to be free from curing membrane, sealer or any other contamination, which could impair good adhesion.

Surfaces to be protected must be sound, smooth, dry and at a minimum temperature of 15°C.

If prior repairs or leveling should be required, consult Chemor for a selection of materials compatible with CHEMORPARK system.

Chemorpark IIIDescriptionCHEMORPARK is a coating system that protects parking decks against corrosion of the reinforcing steel(rebars) and against damage to the concrete.

CHEMORPARK is applied on reinforced concrete decks to protect against the infiltration of water and chlorides.

The system hardens by the in place polymerization of its components.

The base coat film,CHEMORFLEX 350, will bridge cracks up to 1.6mm wide as specified in ASTM C-957 and CSA S413-94.

CHEMORPARK consists of three components and normally it is not necessary to preprime dense the concrete.(If in doubt, consult Chemor technical adviser).

Elastomeric membrane CHEMORFLEX 350This product is based on a polyurethane/epoxy copolymer com-bining the outstanding and complementary properties of its constituent polymers: elasticity of the polyurethane combined with tenacious adhesion and toughness of the epoxy.

CHEMORCLAD 1700 Wear courseThis 100% solids coating is based on a flexibilized epoxy to ensure its compatibility with elastomeric membrane CHEMORFLEX 350.

It also acts as a powerful binder for the incorporated aggregates.

CHEMORCLAD 1800 Tie-coatThis flexibilized 100% solids epoxy coating serves to coat and consolidate the aggregates on the surface of the wear coat.

Waterproofing / Chemorpark III

45 Tri-Tex co inc.

CONSTRUCTIONc


Table I

Characteristic Membrane Wear course Tie-coat

Chemorflex 350

Chemorclad 1700 Wear course

Chemorclad 1800 Tie-coat

Presentation 2-component product

Ratio A/B(by vol.)

8/1 2/1 2/1

Color Grey C-4369 Grey C-4379 Grey C-4379

Solids content 100%

Viscosity 9000 ± 1000 mPa.s

2500 mPa.s 350 mPa.s

Pot life (mixed)(200g @ 21°C)

45-50 min. 60 min. 60 min.

Curing @ 20°C, 50% HR

To recoat 8-24 hrs.* 18-72 hrs. ------

Automobiletraffic

Complete system 48 hrs.

* Higher temperatures will accelerate and lower temperatures will prolong curing time. CHEMORFLEX 350 membrane should be top coated as soon as its surface will support pedestrian traffic.

CHEMORPARK system is not recommended for slabs on grade not equipped with a vapor barrier.To ensure water vapor transmission, moisture proofing silane or siloxane sealer should be used.(Consult your Chemor technical adviser).

InstallationNOTES:• Humidity in concrete must not exceed 15%.• Materials should be conditioned at a temperature

between 18ºC - 26ºC.• Minimum temperature of 15ºC at the time of applications

and during the cure. Lower temperatures prolong curing time whereas higher ones accelerate it.

• For maximum waterproofness the juncture walls/floors and columns/floors should also be protected by carrying the system application continuously 10cm onto vertical surfaces.

Surface preparation

New concreteProvide a relatively smooth finish by a wood float or afine hair broom for a good adhesion of the membrane.

Concrete should be water-cured (liquid curing membranes impair membrane bonding).

New or old concreteThorough cleaning and removal of any contaminant (e.g. oil, grease, laitance, paint, etc.) and of deteriorated or spalled concrete is required.

Concrete preparation by a mechanical method.

Remove all the debris, residues and dust completely.

For crack repair, filling, levelling, follow manufacturer’sinstructions.


46 Tri-Tex co inc.

CONSTRUCTIONc

Chemical resistance

ASTMC-957

water Excellent Excellent

Ethylene glycol (anti-freeze)

Excellent Excellent

Mineral spirit

Very good Excellent

Detergent 7%

Excellent Excellent

Hydraulic fluid

Very good Very good

Motor oil Excellent Excellent

Deicing salts Excellent Excellent

NOTE Results on the actual surface can show some variation from those of the laboratory. The results reported for CHEMORCLAD 1700 and 1800 are for the binders without aggregates.

Application details

Table III

Chemorflex350

Chemorclad1700 Wear course

Chemorclad1800 Tie coat

Thickness binder

Parkingstalls

0,75 mm30 mils1,32 m2/I.

0,30 mm12 mils3,25 m2/I.

0,10mm4 mils9,9 m2/I.

Trafficlanes

0,75 mm30 mils1,32 m2/I.

0,375 mm15 mils2,60 m2/I.

0,10 mm4 mils9,9 m2/I.

Ramps/turning points

0,75 mm30 mils1,32 m2/I.

0,75 mm30 mils1,3 m2/I.

0,15 mm6 mils6,6 m2/I.

NOTE: Ramps and steeps slopes could require coarseraggregates.

Typical technical data

Table II

Property Test method Results

Chemorflex 350membrane

Chemorclad 1700 Wear course andChemorclad 1800 Tie coat

Adhesion AASHTO T-237

100% break in concrete (1.9-2.2 MPa)

Excellent to chemorflex 350

Elongation ASTMD-412 350% 30%

Hardness ASTMD-2240 60-70 (Shore A)

70-80 (Shore D)

Permeability ASTME-96 6.9 ng/Pa.s.m²

4.5 ng/Pa.s.m²

Abrasion resistance

ASTMD-4060 (taber,wheel cs-17,1000 g.weight,1000 cycles)

0.015 g 0.040 g

Tear resistance

ASTM D-624 22 N/mm -------

Tensile strength

ASTM D-412 8 MPa 25 MPa

Crack bridging (@ 0.75mm)

ASTM C-957 CSA S413-94

1.6mm -------


47 Tri-Tex co inc.

CONSTRUCTIONc

MaintenanceHose deck surfaces periodically to remove de-icing salts and debris. Repairs are easily carried out using original liquid chemorpark materials. Consult the manufacturerand follow their recommendations.

Technical serviceAvailable on request.

WarrantyAvailable separately on request.

SafetyContact of the products with the eyes and the skin should be avoided.

Do not breathe vapors of the products.

In case of irritation, immediately seek medical assistance.



Refer to materials safety data sheet (msds).

Application

CHEMORFLEX 350 MembraneUnder agitation add Part B (hardener) to Part A (resin) in theratio indicated on the containers. Continue mixing till the material is homogeneous. Using a notched squeegee spread liquid membrane at minimum thickness of 0.75mmcorresponding to the coverage of 1.32m²/L. Roll-back the material to ensure complete contact with deck surface and a uniform thickness. For interior applications, at normal temperatures of 15-23°C., allow membrane to cure a maximum of 24 hours before applying the wear course. For higher temperatures and for exterior applications, applythe wear course as soon as the membrane becomes tack free. Longer curing time of the membrane could impair the adhesion of the wear course. If recommended curing timesor temperatures are exceeded, it will be necessary to activate the surface of the membrane with Chemor activator SV-42.

CHEMORCLAD 1700 Wear courseMix well separately Parts A & B prior to blending them together. Under agitation add Part B (hardener) to Part A (resin) in the ratio indicated on the containers.Continue mixing till the material is homogeneous.Spread out the mix with a notched squeegee to meet specified minimum thicknesses for different deck andramp areas (refer to Table III).Roll-back the material to ensure complete contact with the membrane and a uniform thickness.

Aggregate incorporationBroadcast pre-selected aggregates (cf. p.1 «Aggregate») onto wet wear course coat until it becomes fullysaturated.

CHEMORCLAD 1800 Tie-coatWithin 24-72 hours remove any excess of aggregates from the surface of the wear course coat. Spray apply at specified thickness a tie coat of CHEMORCLAD 1800.

Allow to harden for 2-4 days, depending on ambient temperature, before opening to vehicular traffic.


48 Tri-Tex co inc.

CONSTRUCTIONc

UsesFor repairs or restoration of concrete structures such as:roads, sidewalks, bridges, viaducts, reservoirs, sewer or water pipes, dams, floors, prefabricated panels,etc.

LimitationsDo not add sand (it could weaken the adhesion and alter thefluidity).

Do not mix longer than one minute.

Only mix the volume that can be placed within 5 minutes.

Do not add water to rework material older than 5 mins.

Do not use as a coating for applications thinner than 19mm.(See «Recommandations»)

Technical Data

Compressive strengthASTM C 10921°C,50% HR

Water Chemorcrete WR 22





Adhesion strengthCan A23.2-6B21°C,50% HR


7 jours 1,2 MPa 4,5 MPa

Bending strengthASTM C 34821°C,50% HR


3 jours 9MPa

28 jours 4,5 MPa 13,5 MPa

Chemorciment 525DescriptionCHEMORCIMENT 525 is a ready to use product, designed for rapid and permanent repair of concrete and masonry.

The product is non-shrinking and contains no metallicadditives. Use of Chemorciment 525 requires only the addition of water.

This product can be used above or below water.

Advantages

Rapid setInitial set 5-10 mins.Final set 25-30 mins.

For vertical, horizontal, or ceiling application.

No formwork necessary.

Permits traffic within approximately one hour after application.

Outstanding adhesion.

Non-shrink.

Non-metallic.

Does not contain calcium chloride.

Good resistance to deicing salts and to freeeze-thaw.

Accepts up to 80% by weight of aggregates.(see Recommendation).

Mortars / Chemorciment 525

49 Tri-Tex co inc.

CONSTRUCTIONc

Surfaces should be saturated with water just prior to placing CHEMORCIMENT 525.

Mixing and placing

MixMix in the proportions of 5.2 liters of water per 25kg bag ofCHEMORCIMENT 525.

Add the product to the water and mix just long enough to obtain a uniform consistency of a nonsagging mastic.

Do not exceed one minute of mixing.

Do not add sand nor calcium chloride.

If the addition of aggregate is required,add the washed aggregate (10mm max. size) to the water prior to adding CHEMORCIMENT 525, then proceed as above.

PlacingPlace the mix by hand or by trowel compressing it to assure complete contact with the surface to be covered.

For vertical or overhead surfaces, apply the mortar in 50mm to 75mm thick coats.

Allow it to achieve initial set prior to making a subsequent application.

For deep repairs, place the mix with aggregate leaving approximately 25mm deep for finishing with mortar not containing aggregate.

FinishingThe surface can be finished 5 minutes after placing the mortar.

For applications under water, finish by hand.

Curing time21°C,5O% HR


Initial approx. 15 min

approx. 30 min

Final approx. 30 min

approx. 1 h

YieldYield per 25kg bag 14.0 l.(0.014m3).

Packaging:25kg moisture resistant bags.

Shelf life12 months stored in a dry location.

Physical appearancePale grey

RecommendationsA prior application of an adhesive is recommended when applied thicknesses will be less then 1.9cm or when substrates are very smooth.

Adhesives CHEMORCRETE SB or WR for dry service conditions and CHEMORSET 100 M for humid service conditions.

If the addition of aggregate is required, up to 80% by weight of washed gravel of 10mm max. size is recommended.

Surface preparationThe surface must be clean and free of oil, grease, paint, laitance, dust and all other contaminants.

Remove all loose and scaling material.

The sides of areas to be repaired should be perpendicular to the surface.


50 Tri-Tex co inc.

CONSTRUCTIONc

CuringWhen the ambient temperature is high and/or there is strong air movement it is advisable to lightly spray the surface during the first 20 mins.after finishing.

Alternatively, a curing membrane conforming to ASTM C-309 can be appllied.

Clean-upWith water, immediately after use.

SafetyProduct is alkaline.


Wash with clean water.



51 Tri-Tex co inc.

CONSTRUCTIONc

Coverages at various thicknesses

Ingredients 1 mm 2 mm 10 mm 50 mm

Chemorfil E 1 l. 1 l. 1 l. 1 l.

Sand #40 1/1,5 l. 1 l.

Sand #16 3 l. 4 l.

Stone 5 l.

Coverage 1 mm 2 mm 10 mm 50 mm

Chemorfil E

m2/l. 0,99 0,86 0,315 0,126

p.c./l. 10,66 9,34 3,39 1,36

Sand # 40

m2/kg 0,43 0,209

p.c./kg 4,63 2,25

Sand # 16

m2/kg 0,07 0,019

p.c./kg 0,75 0,20

Stone

m2/kg 0,016

p.c./kg 0,17

Formulae for suggested mixesAll proportions indicated are in parts by volume:

Ingredients Thickness

0-1mm 1mm-3mm

3mm-10mm

10mm-50mm

CHEMORFIL “E” binder 1 1 1 1

Silica sand # 40 mesh 0 1.0-1.5 1 0

Silica sand # 16 mesh 0 -- 3 4

Dry stones(maximum dimension of not more than one-half of the thickness of theapplication)

0 0 0 5

Chemorfil EDescriptionCHEMORFIL «E» is a two-component epoxy binder for repair of concrete slabs. It can be used as a grout, mortar or epoxy-concrete when mixed with appropriate aggre-gate.

Advantages• Rapid curing.• Allows work to progress quickly with a complete epoxy

system.• No shrinkage: contains no volatile matter (neither• solvents nor water).• High mechanical and chemical resistance.

UsesLevelling and filling of slabs with thicknesses of 0 mm to 40 mm per application.

LimitationsTemperature during application and for at least 18 hrs. after should be at least 10°C.Relative humidity during this same period should not exceed 80%. The concrete should be sound, dry and clean.During application and curing of CHEMORFIL “E” in locations where food products are processed or stored, adequate ventilation must be provided to prevent contamination of the food (taste, odor, etc.) by volatile constituents in the coating.Can be exposed to short intervals of temperatures up to 60°C. Conti-nuous service should not exceed 40°C.

Surface preparationnew concrete should be wet cured because curing membranes can affect adhesion. Humidity of the concretemust not exceed 15%.The concrete surface can be prepared by mechanical or chemical means.

Mortars / Chemorfil E

52 Tri-Tex co inc.

CONSTRUCTIONc

SafetyProducts are combustible in the liquid state.

Keep away from sparks and open flames.





CharacteristicsTypical physical properties

Property Test Result

Compressive Strength

ASTM C-579 80 MPa

Tensile Strength ASTM C-307 18 MPa

Flexural Strength ASTM C-580 34 MPa

Bond Strength AASHTO T-237 2.8 MPa (100% concrete failure)

Abrasion resistance ASTM D-4060 (Taber abrader, CS-17 Wheel, 1000g load, 1000 cycles)

0.1g max. loss

Hardness (Shore D) ASTM D-2240 86

Water absorption ASTM D-570 0.1%

Thermal coefficient of linear expansion

ASTM E-831 2.5 x 10-6/mm/mm/°C

Flammability ASTM D-635 Self-extinguishing

Toxicity Agriculture Canada

Accepted for use in meat processing plants.

Application

PrimingFor thicknesses greater than 3mm, use CHEMORFIL «E» binder as a primer. (Priming is not required for thicknesses less than 3mm: selflevelling grout).

Grout/Mortar/ConcretePrepare trial mixes before finalising the formula.

Mortars / Chemorfil E

53 Tri-Tex co inc.

CONSTRUCTIONc


Two-component product.

Color cement grey.

Non-flammable.

Initial set (@ 20°C) 3 hours.Final set (@ 20°C) 6 hours.

PackagingCHEMORGROUT 200 25kg bags.CHEMORCRETE WR-22 18.9 L pails. 208 L drums.Shelf LifeOne year in original packaging kept in a dry location between 4°C and 30°C.


Property Test method Report

Compressive strength

CSA A23.2-8A ASTM C-109

7d. 28d.

Mortar 55MPa 67MPa

Grout 47MPa 58Mpa

Adhesion CSA A23.2-6BACI 506

Result

Concrete 4.2MPa

Granite 4.8MPa

Freeze/thaw resistance with deicing salts

ASTM C-672 50 cycles

0.18% mass loss

Chemorgrout 200 /Chemorcrete WR 22DescriptionTwo components product consisting of a dry mix (CHEMORGROUT 200) and polymer emulsion (CHEMORCRETE WR-22).

Blending of the two components in varying ratiosproduces highly resistant grouts and mortars.

Advantages• Shock, deicing salts resistant.• Strong adhesion.• High compressive strength.• Superior flexibility.• Water resistant.

UsesInterior/exterior.

Concrete repairs, flooring installations of natural stone andbrick.

LimitationsAmbient and substrate minimum temperature of 7°C.

CHEMORCRETE WR-22 must be protected from freezing.

Do not use any air entraining agent or superplasticizer.

Mortars / Chemorgrout 200 & Chemorcrete WR 22

54 Tri-Tex co inc.

CONSTRUCTIONc

ApplicationFreshly prepared slurry is broomed onto the concrete surface.

While the bondcoat is still wet spread the mortar and compact well.

Apply slurry bondcoat to the surface of the mortar.

While the bondcoat is wet and sticky, place back-moistened flooring units and beat in well.

Allow to set for a minimum of 24 hours at 21°C prior to jointfilling with a grout consistency (manual or pumpable).

CleaningRemove excess grout from the surface while it is still freshwith a damp sponge or a damp towel.

Hardened grout can only be removed mechanically.

Clean tools with water immediately after use.

TemperatureThe setting of bondcoats, mortars and grouts is retarded by low temperatures and accelerated by high ones.

Protect finished work for an extended period when installing in cold weather.

CuringProtect finished work against quick drying. Moist 3 days curing is recommended for optimum properties.

Do not use solvent-based curing membranes.

SafetyProtect skin and eyes against the alkalinity of cement and possible irritation by the polymer CHEMORCRETE WR-22Wash with clean water.

If irritation occurs, consult a physician immediately.

Refer to Materials Safety Data Sheet (MSDS).

Suggered mixed

Bond coat/joint filing grout

CHEMORGROUT 200 1 bag 25kg

CHEMORCRETE WR-22 5.3L

Yield 13.1 L= 0.0131m³Thick mortar bed



Yield 12.7 L= 0.0127m³Fluid mortar



Yield 12.6 L= 0.0122m³

Concrete surface preparationDense or smooth surfaces must be roughened by mechanical or chemical means to obtain a profileof at least 1.5mm.

The surface must be sound and clean, free from grease, oil or any other contaminant or defective concrete.

Saturate with water prior to the bondcoat application.

Do not allow water to pool.

MixingPlace CHEMORCRETE WR-22 in a low speed (250 spm) mixer.

Under agitation, add progressively CHEMORGROUT 200 dry mix and mix to a smooth consistency.

Fluidity can be adjusted by adding more CHEMORCRETE WR-22.

Limit mixing time to a minimum 1-2 minutes to minimize airentrainment.

Mortars / Chemorgrout 200 & Chemorcrete WR 22

55 Tri-Tex co inc.

CONSTRUCTIONc

Not recommended for continous exposure above 80ºC (dry) and above 55ºC (water saturated).

Concrete must not be frozen at the time of application to allow penetration of the priming coat for strong adhesion.

Technical Data

Compressive strengthASTM C 109

5°C 22°C 32°C

3 hours 28 MPa


10 hours 31 MPa




Presentation3-component product, prepackagedin a single container.

Part A resin 1.5 L. ( 1.70 kg)Part B hardener 0.75 L. ( 0.75 kg)Part C aggregate 8.25 L. (14.3 kg)

Weight/unit 16.75 kg.

Yield/unit approx. 7.5 L or 0.0075 m3

Yield at 6mm thickness 1.25m2/Unit or 0.167m²/L.

Color cement-grey.

Pot life of mix (500g mass, minutes)5°C 120 min23°C 45 min32°C 35 à 40 min

Chemorpatch 66DescriptionCHEMORPATCH 66 is 3-component, prepackaged, ready to use, ambient temperature curing, epoxy mortar for repairing concrete structures,interior and exterior.

The product is packaged as one unit which contains threecomponents; these must be mixed together before use.

The product is 100% solids -no solvent or water.

AdvantagesMuch stronger than concrete.

Insensitive to moisture in concrete before, during and afterapplication.

Resistant to freeze/thaw.

Remarkable adhesion to concrete and steel.

Excellent resistance to shock and abrasion (wear).

Positive cure at 5°C.

Fast ambient cure; (22°C): ready for heavy traffic in 6 hours.


For buiding and engineering work.

Highly durable chemical resistant concrete repairs: floors, walls, columns, tanks, overpasses, bridges, etc.

LimitationsDo not dilute the product: solvents prevent proper hardening.

For best results do not apply at ambient or surface temperatures below 10ºC.

Mortars / Chemorpatch 66

56 Tri-Tex co inc.

CONSTRUCTIONc

If more than 10% is used the volume of aggregate which is added to make the mortar should be reduced proportionately. The ratio of aggregate to resin should bearound 4 to 1 by volume.

MortarImmediately following priming add slowly, while mixing, the aggregate, Part C, to the previously prepared liquid mix and continue mixing until homogeneous.

Placing and finishingThe primer must be still tacky when placing the mortar. If not, reapply a thin coat of primer.

Spread the mortar at the required thickness, place it carefully to ensure complete contact with concrete.

Compact and smooth with a trowel to obtain a uniform, levelfinish.

SafetyLiquid product is combustible.Keep away from flame and sparks.Contact could cause dermatitis.Protect eyes and skin.Use protective gloves and safety glasses.Do not breathe vapors.Wash with soap and water.If irritation persists, consult physician.Refer to «Materials Safety Data Sheet» (MSDS).

Curing time 5°C 22°C 32°C

Ready for traffic (hours)

8h 4h 3h

Complete hardening (hours)

72h 24h 24h

Adhesion to concrete (ASTM-C-882) dry 24 MPasaturated surface dry 19 MPa

Modulus of elasticity (ASTM-C-469) 22 GPa

Surface preparation

ConcreteThe surface must be sound and clean, free of grease,oil, rust and all other contaminants to assure good adhesion.

SteelRemove rust; then degrease and clean with METPREP. For maximum protection against corrosion prime with CHEMORCLAD 9500.

Application

NOTENever dilute with solvent. For maximum impact and wearresistance, a thickness of at least 6mm is recommended.

MixingIn the Part A container mix together at slow speed Parts Aand B with an electric mixer for 3-4 minutes.

PrimingUse this liquid mix as is to prime the surface which is to berepaired: approximately 10% of the mix is provided for this use.

Mortars / Chemorpatch 66

57 Tri-Tex co inc.

CONSTRUCTIONc

UsesInterior or exterior.

New work or maintenance.

Walls,floors,ceilings,machinery and equipment.

Most useful for areas requiring high resistance and durability to foot or vehicular traffic, to water, deicing salts, chemicals or impact.

Industrial plants, warehouses, garages, mechanical rooms, boat decks, arenas, hospitals, recreation centres, balconies, laundry rooms, shower rooms, bathrooms, etc.

LimitationsNew concrete must have cured for at least 21 days.

Surfaces to be coated should have a maximum humidity content of 15%.

Being a vapor-barrier, the coating must not be exposed to hydrostatic pressure: concrete slabs on grade should be protected by a vapor barrier.

Low temperatures extend curing time.

For best results,minimum ambient and substrate temperature of 15°C is recommended during the applicationand curing of the coating.

During application and curing of the coating in locations where food products are stored, adequate ventilation must be provided to prevent contamination of the food (taste, odor, etc.) by volatile constituents of the coating.

Coating can be exposed to short intervals of temperatures up to 60°C. Temperatures for continuous service should not exceed 40°C.

On weathering, some chalking and yellowing should be expected. However, the integrity and protective properties of the coating remain unaffected.

Chemorclad 200DescriptionCHEMORCLAD 200 is a 100% solids two-component epoxy coating curing at ambient temperature.

It is designed as a high build protective and decorative coating for a variety of substrates subjected to severe service conditions: concrete, masonry, wood, plywood, asbestos-cement panel, wallboard,metals.

Cured coating is hard and resistant to many common chemicals.

Can be reinforced with glass fibre mats.

Advantages• Safe, very little odor: contains no flammable volatile

solvents.• Protects dry or wet surfaces.• Remains flexible: high impact resistance.• Excellent adhesion to concrete, masonry and steel.• Superior abrasion (wear)resistance.• Resistant to common chemicals.• Choice of decorative colors.• Ease of maintenance.• Non-toxic (accepted by Agriculture Canada).

TypesTwo types are available:• Clear gloss.• Pigmented gloss.

FinishesOrange peel or anti-skid (variable, depending on the enduse requirements).

ColorsStandard colors as per Chemor Color Chart.Special colors available on request.

Primers & Coatings / Chemorclad 200

58 Tri-Tex co inc.

CONSTRUCTIONc


Tensile strength 43 MPa.(ASTM D-638)

Elongation at break min. 5%.(ASTM C-638)

Impact resistance min. 15.0J(1-GP-71; 147.1) Recto

Adhesion strength 2.7MPa(AASHTO-T-237) (100% concrete rupture)

Hardness 75-80(ASTM D-2240-Shore D)

Abrasion resistance loss of 55mg(ASTM D-4060)1000 cycles, wheel CS17, weight 1000g.

Scrubbability passes 10,000 cycles.(1-GP-71;125.1 )


Water vapor transmission 6.9ng/Pa.s.m2

(ASTM E-96)

Flammability self-extinguishing(ASTM D-635)

Toxicity Accepted by Agriculture Canada

WaterproofnessTo ensure waterproofness against possible light cracking of concrete, a prior application of an elastomeric waterproofing membrane CHEMORFLEX 300 is recommended (e.g. mechanical rooms, computer rooms,etc.).

Characteristics


Pot life 50 mins.(100g mass @ 21°C)

Viscosity (mixed) approx. 3400 mPa.s (depending on color).

Solids content 100%

Flash point 204°C

Coverage (dry film/coat) 3.9m²/l.@ 0.25mm (maximum thickness/ coat for walls). 1.95m²/l. @ 0.50mm (maximum thickness/ coat for floors).

Curing time (@ 21°C)

Tack-free 7 hoursRecoat 24 hoursTraffic pedestrian 24 hoursTraffic vehicular 48 hoursChemical resistance 7 days

Cleaner & reducer Chemor solvent SV-40

Shelf life One year minimum in original sealed containers.


59 Tri-Tex co inc.

CONSTRUCTIONc

ConcreteMust be dry, sound,free from curing membrane or sealer.

Dust, laitance, grease,oil, rust, wax or any other contaminant, if present, must be removed.

Floor must be prepared by appropriate chemical or mechanical means.

Repairs : large cracks and cavities must be filled withChemorpatch 66 or a Chemortop cement-latex mortar.

Narrow cracks and small holes should be masticated withChemorclad 9200.

For crack injection use Chemorset 100 LV.

MasonryJoints must be sound and dense. Clean and prime.

WoodSand, clean and prime.

SteelDegrease and derust with Metprep. Wire brush or grind.Deep rust : blast; prime.

Non-ferrous metalsDegrease and etch with Metprep; prime.

Chemical resistanceASTM D 1308covered for 7 days.

Reagent Result

Detergent solution (5% Ajax), 20% sodium chloride,20% calcium chloride, 20% ammonia, 20% sodiumbicarbonate, 20% sodium triphosphate, 20% caustic soda, 3% Javex, 5% lactic acid, 10% citric acid, 10% hydrochloric acid, mineral spirits, toluene, xylene, methanol, lead-free gasoline, Skydrol, beer, coffee, tea.

Unaltered

10% nitric acid Light yellowing

10% sulphuric acid Slight discoloration

Surface preparation

PrimersDense concrete,cement-asbestos, wood : Chemorclad 9000 or 9100.

Porous concrete,concrete bloc, masonry (walls) :Chemolac 1030 or Chemorclad 9200.

Ferrous metals : Chemorclad 9500.

Non-Ferrous metals : Metprep followed by Chemorclad 9500.

Wallboard : Chemolac 1020, Chemorclad 9100 orChemorclad 9000.


60 Tri-Tex co inc.

CONSTRUCTIONc

SafetyKeep away from flame and sparks.








Directions for use

MixNOTE: Mix only such quantities which can be used before the expiration of the pot life.

Mix each Part separately prior to proportioning them in a clean container.

Mix well Parts A and B together with a low speed drill or manual spatula for small quantities.

For spray application only, reduce 5-10% with Chemor Solvent SV-40.

ApplicationNumber of coats : normally two.

Brush, shortnap roller,spray.

Because of the relatively high viscosity of CHEMORCLAD 200, heavy duty airless spray equipment is recommended.

Typical equipment suitable for this is «GRACO» King45:1 with 50 p.s.i. inlet pressure and 521 (RAC IV) tip.

Time interval between coats should not exceed 24 hours.

Otherwise, the previous coat must be scuff sanded to ensure good adhesion.

Non-skid finishes.To the mix of Parts A and B add dry crushed silica sand as follows:

Mesh Quantity

Very Light # 70 70 g/l.

Light # 40 100 g/l.

Medium # 24 200 g/l.

Coarse # 16/24 200 g/l.


61 Tri-Tex co inc.

CONSTRUCTIONc


New work or maintenance of floors.

Most useful for areas requiring high resistance and durability to foot or vehicular traffic, to water, deicing salts, chemicals or impact.

Industrial plants, warehouses, garages, mechanical rooms, arenas, hospitals, recreation centres, balconies, laundry rooms, shower rooms, bathrooms, etc.



Being a vapor-barrier, the coating must not be exposed tohydrosta- tic pressure : concrete slabs on grade should beprotected by a vapor barrier.


For best results, minimum ambient and substrate temperature of 15°C is recommended during the applicationand curing of the coating.


Coating can be exposed to short intervals of temperatures up to 60°C.

Temperatures for continuous service should not exceed 40°C.

On weathering, some chalking and yellowing should be expected.

However, the integrity and protective properties of thecoating remain unaffected.

Chemorclad 200 C SLDescriptionCHEMORCLAD 200 C SL is a 100% solids two-component epoxy coating curing at ambient temperature.

It is designed as a high build protective and decorative coating for a variety of substrates subjected to severe service conditions: concrete, wood, plywood, metals.

Cured coating is smooth, hard and resistant to many common chemicals.

Can be reinforced with glass fibre mats.

Advantages• Safe, very little odor : contains no flammable volatile

solvents.• Protects dry or wet surfaces.• Remains flexible : high impact resistance.• Excellent adhesion to concrete, steel and wood.• Superior abrasion (wear)resistance.• Resistant to common chemicals.• Choice of decorative colors.• Ease of maintenance.• Non-toxic (accepted by Agriculture Canada).

TypesTwo types are available :• Clear gloss.• Pigmented gloss.

FinishesSmooth or anti-skid(variable, depending on the end use requirements).

ColorsStandard colors as per Chemor Color Chart.Special colors available on request.

Primers & Coatings / Chemorclad 200 C SL

62 Tri-Tex co inc.

CONSTRUCTIONc


Tensile strength 43 MPa.(ASTM D-638)

Elongation at break min. 7%.(ASTM C-638)


Adhesion strength 2.7MPa(AASHTO-T-237) (100% concrete rupture)



Scrubbability passes 10,000 cycles.(1-GP-71;125.1 )


Water vapor transmission 6.9ng/Pa.s.m2

(ASTM E-96)


Toxicity Accepted by Agriculture Canada

WaterproofnessTo ensure waterproofness against possible light cracking of concrete, a prior application of an elastomeric waterproofing membrane CHEMORFLEX 350 is recommended (e.g. mechanical rooms, computer rooms, etc.).

Characteristics

Presentation2-component product Parts A and B

Pot life 50 mins(100g mass @ 21°C)

Viscosity (A+B) approx.600 mPa.s (depending on color)

Solids content 100%

Flash point 204°C

Coverage (dry film/coat) 3.9m²/L @ 0.25mm (10mils).

1.95m²/L @ 0.50mm (20mils).


Tack-free 7 hoursRecoat 24 hoursTraffic pedestrian 24 hoursTraffic vehicular 48 hours


Shelf life one year minimum in original sealed containers.


63 Tri-Tex co inc.

CONSTRUCTIONc

Narrow cracks and small holes should be masticated withChemorclad 9200. For crack injection use Chemorset 100 LV.

WoodSand, clean and prime.

SteelDegrease and derust with Metprep. Wire brush or grind.

Deep rust : blast; prime.

Non-ferrous metalsDegrease and etch with Metprep; prime.

Directions for use

MixNOTE : Mix only such quantities which can be used before the expiration of the pot life.



For spray application only, reduce 5-10% with Chemor Solvent SV-40.

ApplicationNumber of coats : normally two.

Brush, shortnap roller, spray.

Time interval between coats should not exceed 24 hours.Otherwise, the previous coat must be scuff sanded to ensure good adhesion.


Reagent Result


Unaltered

Surface preparation

PrimersDense concrete, cement-asbestos, wood : Chemorclad 9000, 9030 or 9100.

Ferrous metals : Chemorclad 9600.

Non-Ferrous metals : Metprep followed by Chemorclad 9600.

Wood : Chemorclad 9000.

ConcreteMust be dry, sound, free from curing membrane or sealer.Dust, laitance, grease, oil, rust, wax or any other contaminant, if present, must be removed.


Repairs : large cracks and cavities must be filled withChemorpatch 66 or a Chemortop cement-latex mortar.


64 Tri-Tex co inc.

CONSTRUCTIONc


Mesh Quantity


Light # 40 100 g/l.


Coarse # 16/24 200 g/l.








Refer to “Materials Safety Data Sheet” (MSSD).


65 Tri-Tex co inc.

CONSTRUCTIONc

Being a vapor-barrier, the coating must not be exposed to hydrostatic pressure : concrete slabs on grade should be protected by a vapor barrier.

Low temperatures extend curing time, whereas higher ones shorten it.

For best results, minimum ambient and substrate temperature of 15°C is recommended during the application and curing of the coating.


Coating can be exposed to short intervals of temperatures up to 60°C.


WaterproofnessTo ensure waterproofness against possible light cracking of concrete, a prior application of an elastomeric waterproofing membrane CHEMORFLEX 350 is recommended (e.g. mechanical rooms, computer rooms, etc.).

Chemorclad 250DescriptionCHEMORCLAD 250 is a 100% solids two-component epoxy coating fast curing at ambient temperature.

Cured coating is hard and resistant to many common chemicals.

This product is solventless at 100% solids content comprising epoxy resins, mineral pigments, flexibilizing agents and polymerising hardness.

ColorsStandard color is grey C-4195.Special colors are available on request.

FinishesChoice of smooth or non-skid.

Advantages• Fast installation schedule, serviceable in a few hours.• Sanitary, impervious, durable.• Hard and resistant to heavy traffic.• Resistant to alkalies, some diluted acids and common• maintenance chemicals.• Resistant to micro-organisms

(approved by Agriculture Canada)

UsesInterior.Food industry, refrigerator, bottling plants, heavyindustries, wherever short installation schedules arerequired.




66 Tri-Tex co inc.

CONSTRUCTIONc


Tensile strength 43 MPa(ASTM D-638)

Elongation at break min. 5%(ASTM C-638)


Bond strength 2.7MPa (100% (AASHTO-T-237) concrete rupture).



Scrubbability passes 10,000 cycles(1-GP-71;125.1 )


Water vapor transmission 6.9ng/Pa.s.m².(ASTM E-96)


Toxicity accepted by Agriculture Canada.

Characteristics

Presentation 2-component product Parts A and B

Pot life 20-25 mins(100g mass @ 21°C)

Viscosity (mixed) approx. 2500 ± 500 mPa.s (depending on color).

Solids content 100%

Flash point 204°C

Coverage (dry film/coat) 3.9m²/l.@ 0.25mm (10mils)

2.9m²/l.@ 0.375mm (15 mils) (maximum thickness/ coat for floors).


Tack-free 3 hoursRecoat 4 hoursTraffic pedestrian 4 hoursTraffic vehicular 8 hoursChemical resistance 7 days


Shelf life one year minimum in original sealed containers.


67 Tri-Tex co inc.

CONSTRUCTIONc


PrimingChemorclad 9030, fast setting epoxy primer.

Apply one coat to concrete saturation.

Allow to harden for maximum 12 hours @ 21°C beforefinishing with Chemorclad 250.

Directions for use




ApplicationNumber of coats : one or two.

Pour freshly prepared mix on a floor section which can be finished within about 15 minutes.

Spread-out the coating with a squeegee and smooth it out with a 5mm roller.

Joint subsequent sections while the coating is still fluid.

Time interval between coats should not exceed 12 hours.

Otherwise, the previous coat must be scuff-sanded to ensure good adhesion.


Reagent Result


Unaltered

Surface preparation

ConcreteMust be dry, sound, free from curing membrane or sealer.

Dust, laitance, grease, oil, rust, wax or any other contaminant, if present, must be removed.

Slabs on grade should be protected by a vapor barrier as specified by the National Building Code.

New concrete should be water cured because curing membranes impair good adhesion.

Humidity content should not exceed 15%.


Repairs : large cracks and cavities must be filled with Chemorpatch 66 or a Chemortop cement-latex mortar.

Narrow cracks and small holes should be masticated withChemorclad 9200.


68 Tri-Tex co inc.

CONSTRUCTIONc


Mesh Quantity


Light # 40 100 g/l.


Coarse # 16/24 250 g/l.










69 Tri-Tex co inc.

CONSTRUCTIONc

UsesNew work or maintenance of concrete floors.

Warehouses, institutions, factories, etc.

Industrieschemicals, electrical, electronic mechanical, paper, food products, etc.

LimitationsNew concrete must be cured at least 21 days prior to application of CHEMORCLAD 300 SL.

The coating is a vapor barrier, therefore, should not be exposed to hydrostatic pressure.

Slab on grave should be equipped with vapor barrier as recommended by «The National Building code».

Maximum adhesion is achieved on dry concrete with a moisture content of 17% or less.

Low temperatures prolong curing time.

Surfaces to be coated must be at least 15°C.

Temperature during application and for a period of 18 hours following application must be 15°C minimum.

Relative humidity during this same period must not exceed 80%.

Concrete should be completely sealed prior to application of the coating, otherwise residual porosity of the concrete might result in air bubbles or craters in the coating.


Chemorclad 300 SLDescriptionCHEMORCLAD 300 SL is a two or three components epoxy self-levelling filler coating which is supplied at 100% solids at thicknesses from 0.5mm to 2.5mm.

This product was designed to be self-levelling with high filling ability when applied to concrete floors in one coat at a thickness of 0.5mm per coat.

Thus, a single application, following priming, yields a smooth level finish over floors which are uneven in profile.

Results in a hard yet resilient finish which is resistant toabrasion and many common chemicals.

This coating system includes the following :CHEMORCLAD 9000, 9030 or 9100 :2-component epoxy primers, moisture tolerant.

CHEMORCLAD 300 SL :2-component epoxy self-levelling binder.

Optional :Dry silica and 70 mesh (0.1-0.3mm)for blending withCHEMORCLAD 300 SL binder.

AdvantagesProvides a high level of filling in a single application.

Remains flexible (resilient) : resistant to impact.

Superior resistance to wear (abrasion).

Resistant to common chemicals.

Ease of maintenance.

ColorsSee Chemor floor color chart.Other colors available on demand.

Primers & Coatings / Chemorclad 300 SL

70 Tri-Tex co inc.

CONSTRUCTIONc

Self-levelling coating system(Primer required in all cases)

System Components Thickness Installationmethod

A Chemorclad 300 SL

0.5mm-1.0mm(20mils-40mils)

Notched squeegee

B Chemorclad 300 SL


Notched squeegee5mm roller

C Chemorclad 300 SL mixed with ½ volumeof silica sand #70(0.1mm-0.3mm)


Notched squeegee5mm roller

NOTES: Use porcupine roller, instead of 5mm roller as needed, to remove entrapped air.For non-skid finished consult chemor technical service.

Bond strength 2.7Mpa (100%(AASHTO-T-237) concrete rupture)


Water absorption 0.2%.(ASTM D-570)

Thermal resistancecontinuous 50°Cintermittent 75°C

Flammability self-ixtinguishing(ASTM D-635)

Toxicity accepted by Agriculture Canada.

Characteristics

Presentation Parts A & Btwo component product.

Pot Life 30 minutes.(100gm mass @ 21°C)

Viscosity (A + B) 2500 ± 500 mPa.s

Flash Point >100°C

Percent Solids 100%

Coverage (DFT/coat) 2m²/L @ 0.5 mm (minimum)

0.67-0.40²/L @1.5mm-2.5mm

Curing time (@ 21°C):

To recoat 8 to 24 hours maxTraffic pedestrian 12 hoursTraffic vehicular 24 hoursChemical resistance 7 days

Reducing and Cleaning Chemor Solvent SV-40

Storage life minimum of one year in the original unopened container at 17°C-30°C.


71 Tri-Tex co inc.

CONSTRUCTIONc

Concrete PrimerCHEMORCLAD 9000, CHEMORCLAD 9030 or CHEMORCLAD 9100 two component epoxy primers.

Directions for useSingle application on concrete previously primed with Chemorclad 9000 or 9100.

Time interval between coats should not exceed 12 hrs. for 9030, and 24 hrs. for 9000, 9100.

If this interval is exceeded, the primer must be scuff sanded, followed by the reapplication of a thin coat of primer in order to assure maximum adhesion.



Mix well Parts A and B together with a low speed drill (upto 250 r.p.m.) to avoid air entrainment or manual spatula forsmall quantities.

ApplicationNotched squeegee, short nap roller, spray, brush.

Pour the entire fresh mix over the surface, corresponding to the theoretical coverage.

Spread the coating uniformly across the floor to obtain the specified film thickness.

Back-roll with a porcupine roller to eliminate any air bubbles.


Reagent Result


Unaltered

Surface preparation

ConcreteMust be sound, free from any curing membrane or sealer.

Any contamination which may impair good adhesion must be removed, eg. grease, oil, wax, laitenance, rust, etc.

Floors should be etched mechanically or chemically.

Repairs : large cracks and cavities must be filled with Chemorpatch 66 epoxy mortar or Chemortop cement-latexmortar.

Narrow cracks and small holes should be masticated with Chemorclad 9200.


Construction joints : use Chemorclad 400 NS/SL sealant.


72 Tri-Tex co inc.

CONSTRUCTIONc

SafetyLiquid product is flammable.








Refer to «Material Safety Data Sheet» (MSSD).


73 Tri-Tex co inc.

CONSTRUCTIONc

Characteristics

TYPE IPresentation 2 component product Parts A and B

Color Amber.

Part A Polyurethane binder.Part B Aluminium oxide granules.

Mix A and BPart A 3.78 L ; 18.92 L;Part B 0.8 kg ; 4.0kg ;Total Unit Volume 4.l L ; 20.4 L;

TYPE IIPresentation three-component product Parts A, B, C.

Color refer to C-33 color chart.

Part A Polyurethane binder.Part B Colorant.Part C Aluminium oxide granules.

Mix of Parts A, B, C per unitsPart A 3.78 L ; 18.92 L;Part B 0.19 L ; 0.92 L;Total Unit Volume 4.3 L ; 21.3 L;

Pot life approx. 1 hour.(skin formation on the surface).

Flash point 26°C.(closed cup)

Viscosity (Part A) 500 mPa’s.

Chemorclad 1010DescriptionCHEMORCLAD 1010 is a coating system designed for concrete floors subject to heavy traffic.

The coating consists of a transparent urethane binder reinforced with fine aluminium oxide granules.

It cures by reaction with atmospheric moisture.

AdvantagesSuperior wear resistance.

Resistant to common chemicals.

Remains flexible: high impact resistance.


UsesInterior.

New work or maintenance.

Warehouse or factory floors, garages, etc.

Wherever high wear and shock resistance and resistanceto common chemicals are required.

RestrictionsFresh concrete must be allowed to cure at least 3 weeks.


Exposure to ultraviolet rays will cause darkening of thecolor.

The product cures by reaction with atmospheric moisture, so container must be kept tightly closed.


74 Tri-Tex co inc.

CONSTRUCTIONc

Chemical Resistance 24 hours 8 days

ASTM 1308 covered E E

10% sulfuric acid E E

32% sulfuric acid G G

Alcde 30% hydrochloric (muriatic) E E

10% nitric acid G G

40% nitric acid E E

10% acetic acid E F

20% sodium hydroxide E E

30% ammonia E E

Gazoline E E

Xylene G G

Ethyl alcohol E E

Ethylene glycol F

Acetone G G

Skydrol LD4

E= Excellent G=Good F= Fair

The effects of chemical spills will be minimized if they are immediately removed or if they are periodically rinsed with water.

Surface preparationThe concrete must be sound, dry and having cured at least3 weeks.

It must be free of grease, oil, laitance, curing membranes,paints, sealers, rubber tire marks, dust and all othercontaminants that could prevent good penetration of the product.

Remove contaminants by mechanical or chemical means.

Solids contentPart A 64% by weight 57% by volume.Part B 100%Part C 100%

Parts A & B mix 70% by weight 60% by volume.

Curing time (@ 21°C, 50% R.H.)Pedestrian traffic 8 hoursVehicular traffic 24-48 hoursComplete cure 7 days

Coverage (preprimed concrete) average per 2 coats 4m2/L with a total dry film thickness of 0.125mm.

Reducer/Cleaning Solvent Chemor solvent SV-22

Storage one year in original unopened container.

Typical physical properties(@ 21°C, 50% R.H.)

Sward hardness 40

Tensile strength (ASTM D-882) 35 mPa.

Elongation (ASTM D-882) 6%

Abrasion resistance 25 mg(Taber, CS-17 wheel,1000g)


75 Tri-Tex co inc.

CONSTRUCTIONc









Refer to “ Materials Safety Data Sheet” MSDS)

PrimerCHEMORCLAD 9100 OR 9000.

Direction for useThe primer must not be allowed to cure more than 24 hours.

Mix well Part B with Part A of CHEMORCLAD 1010 in the premeasured proportions.

Maintain the granules suspended in the liquid by frequent agitation.

For the mixed product into a roller tray.

Mix with a 10mm roller.

With the same roller apply a coat to saturate the concrete (without leaving an excess).

Over a 3-4m2 area, apply by rolling back and forth, immediately followed by rolling side to side to uniform theappearance.

Excessive/over-rolling could cause bubbling.

Allow curing of 4 to 24 hrs (maximum) before applying thesecond coat, using the same application technique.

Let cure at least 8 hours before allowing pedestrian traffic.

Maximum wear and chemical resistance is attained after7 days curing.

Clean tools and equipment with Chemor SV-22 before curing of the product.


76 Tri-Tex co inc.

CONSTRUCTIONc

LimitationsProtect the product from contact with moisture: being moisturecuring, exposure to air could cause gel formation.

Keep containers closed when not in use.

Do not apply below 15°C and 35% H.R.

Maximum thickness of 0.150mm (6 mils) wet or0.0625mm (2.5 mils) dry per coat.

Higher thickness could result in bubbles formation.

Characteristics

PresentationTYPE I one-component colorless liquid.

TYPE II two-component liquid : Parts A and B.

Pot life (at 21°C.and 50% H.R.)TYPE I transparent 8 hoursTYPE II colored (A+B) 1 hour.

Solids content 42-45%

Viscosity 150 ± 20mPa.s

Flash point min.26°C.

Setting time(@ 21°C and 50% H.R.)Foot 8 hoursVehicular 24 hoursComplete 5-7 days

Coverage (calculated) 6.5m2/L @ 0.0625mm (2.5 mils) dry thicknessor 0.150mm (6 mils) wet thickness per coat.

Chemorclad 2020DescriptionCHEMORCLAD 2020 is a moisture curing aliphatic polyurethane coating.

It is available as a single component clear gloss andtwo-component pigmented, with smooth or non-skid finishes.

TypesTYPE I clearTYPE II pigmented

ColorsTwo standard colorsLight grey C-4514Dark grey C-4510Special colors are available on request (consult sales dept.).

AdvantagesHigh flexibility.Resistance to ultra-violet rays.(color retention).

Resistance to common chemicals.


UsesInterior and exterior.Concrete, steel, wood.Wall and floors.Particularly useful whenever a finish resistant to yellowing is required.Can be installed as a coating system, or as a protective finish coat for other CHEMOR coatings.


77 Tri-Tex co inc.

CONSTRUCTIONc


Reagent Result


Unaltered

Surface preparation

ConcreteNew concrete should be moist-cured.Curing period of at least 28 days.

Surface must be sound and clean, free from laitance, grease, oil, rust, wax, sealers or any other contaminant which may impair good adhesion.

WoodMust be dry, hard and clean.

Any previous surface treatment must be sanded off tobare wood.

Prime with the product as delivered or dilute dependingon porosity of wood surface.

Ferrous metalsDegrease, derust and prime.

Galvanised metalsDegrease, etch with MEPTPREP and prime.

Number of coats One or two as a finish Minimum of two as a system perse

Cleaner/diluent CHEMOR Solvent SV-22

Shelf life one year in factory sealed containers.

Methods of application brush, lambs wool pad, 5mm roller, spray.

PrimersConcrete CHEMORCLAD 9000, 9100Metals CHEMORCLAD 9500Wood self-priming


Property Test method Result

Abrasion resistance

ASTM D 4060-81 wheel CS17, load 1000g1000 cycles.

loss of 38mg

Adhesion (Epoxy primed concrete)

ASTM D 4541 concrete rupture

Tensile strength ASTM D 638 23 MPa

Elongation at break

ASTM D 638 95%

Flexibility ASTM D 522 passes 3.15mm

Impact resistance 1-GP-71 method 147.1

min. 18 J recto

Hardness Sward 35


78 Tri-Tex co inc.

CONSTRUCTIONc

SecurityLiquid product is flammable.








Refer to «Material Safety Data Sheet» (MSDS).

Directions for use

Smooth finish as is.

Non-skid finish broadcast #70 sand and roll.

Mix (Type II pigmented)Add contents of Part B to Part A and mix well to uniformity.

Remix briefly before each use.

Application

AS A SYSTEM PER SEMust follow priming within maximum of 24 hours.

Follow the same interval for finish coats.

If exceeded, check adhesion.

If necessary, depolish hardened coat by scuff-sanding.

AS A FINISH COAT FOR OTHER CHEMOR COATINGSApply within maximum of 24 hours following application of a CHEMOR epoxy coating or CHEMORFLEX 300 membrane (@ 15°-22°C; higher temperatures shorten thisinterval).

If exceeded, depolish by scuff-sanding.


79 Tri-Tex co inc.

CONSTRUCTIONc

Characteristics

Presentation 2-component liquid Parts A and B

Color clear pale amber

Pot life @ 21ºC 40 mins

Viscosity @ 21°C. 400 ± 50 mPa.s

Solids content 100%

Flash point >100°C

Coverage 5.0 - 7.0m2/l/per application (depending on substrate porosity).

Curing time ( @ 21ºC)Touch dry 5-6 hoursTo recoat 12 hours

Diluent/cleaner Chemor solvent SV-40

Shelf-life minimum 1 year in original sealed containers at 10-26ºC

Surface preparation

ConcreteShould be sound and dry, cured for at least 28 days.Free from grease, oil, laitance, curing membrane, sealers, paints, rubber tire marks, dust, or any other contaminant which could impair good adhesion.

Preparation by mechanical or chemical means.

WoodSand and remove dust.

OtherMust be clean.

Chemorclad 9000DescriptionCHEMORCLAD 9000 is a solventless 2-component clear epoxy primersealer setting at ambient temperature.

Designed for sealing absorbent or porous substrates (e.g. concrete, cement-asbestos,masonry) to be finished with a Chemor coating system.

AdvantagesDeep penetration combined with positive anchoring in the substrate due to its high wetting power.

Provides positive bonding for epoxy finishes.


Priming-sealing of concrete, masonry, cement-asbestos or wood prior to the application of recommended 2-component epoxy finishes.

LimitationsDoes not fill apparent cracks.

Both ambient and substrate temperature should be at least15°C during application and curing of the product. (curingtime is shortened by warm but prolonged by cold temperatures).

Should not be applied to surfaces containing more than 23% moisture.

The depth of penetration of the product increases with the dryness of the substrate.


80 Tri-Tex co inc.

CONSTRUCTIONc








Refer to “Materials Safety Data Sheet” (MSSD).

Directions for useNOTE: Any finish should be applied within a 24 hour intervalto the primed surface.

If not, scuff sand prior to the application of the finish.

MixUsing a mechanical mixer blend thoroughly the mix of Parts A and B in the ratio indicated on the label.

ApplicationRoller, rubber squeegee, low pressure spray.

Rate of application is guided by product absorption by the substrate.

Do not pool.

Satisfactory sealing is indicated by the appearance of a uniform, permanent shine on the surface.

Should a second application be required, allow the first one to set.

Clean tools and equipment with Chemor Solvent SV-40 immediately after use.


81 Tri-Tex co inc.

CONSTRUCTIONc

Characteristics

Presentation 2-component liquid Parts A and B.

Color clear pale amber.

Pot life @ 21ºC 15 mins.


Solids content 100%.

Flash point >100°C.

Coverage 5.0 - 7.0m2/L (depending on substrate porosity).

Curing time ( @ 21ºC) To recoat 4 hours.

Diluent/cleaner Chemor solvent SV-40.

Shelf-life minimum 1 year in original sealed containers at 10-26ºC.

Surface preparation

ConcreteShould be sound and dry, cured for at least 28 days.

Free from grease, oil, laitance, curing membrane, sealers, paints, rubber tire marks, dust, or any other contaminant, which could impair good adhesion.


WoodSand and remove dust.

OtherMust be clean.

Chemorclad 9030DescriptionCHEMORCLAD 9030 is a solventless 2-component clear epoxy primer-sealer fast setting at ambient temperature.

Designed for sealing concrete floors to be finished with a Chemor coating system.

AdvantagesFast setting combined with deep penetration produces positive anchoring in the substrate due to its high wetting power.

Allows some floor coatinginstallations to be completed same day.

Free from flammable solvents.


Priming-sealing of concrete, prior to the application of recommended epoxy or polyurethane finishes.


Both ambient and substrate temperature should be at least 15°C during application and curing of the product. (curing time is shortened by warm but prolonged by cold temperatures).




82 Tri-Tex co inc.

CONSTRUCTIONc









Directions for useNOTE: Any finish should be ap-plied within a 12 hour interval to the primed surface.

If not, reactivate the surface with SV-42 activator immediately prior the application of the finish.

MixUsing a mechanical mixer blend thoroughly the mix of Parts A and B in the ratio indicated on the label.

ApplicationRoller, rubber squeegee.

Rate of application is guided by product absorption by thesubstrate.

Do not pool.





83 Tri-Tex co inc.

CONSTRUCTIONc

Characteristics

Presentation 2-component liquid Parts A and B.

Color clear pale amber.

Pot life @ 21ºC 4 hours.


Solids content 81% (by weight) 78% (by volume)

Flash point -6°C.

Coverage 5.5 - 7.1m2/l/per application (depending on substrate porosity).

Curing time ( @ 21ºC)Touch dry 4 hours.To recoat 6 hours.

Diluent/cleaner Chemor solvent SV-40.

Shelf-life minimum 1 year in original sealed containers at 10-26ºC.

Surface preparation

ConcreteShould be sound and dry, cured for at least 28 days.

Free from grease, oil, laitance, curing membrane, sealers, paints, rubber tire marks, dust, or any other contaminant which could impair good adhesion.


Wood : Sand and remove dust.

Other : Must be clean.

Chemorclad 9100DescriptionCHEMORCLAD 9100 is a 2-component solvent based clear epoxy primersealer setting at ambient temperature.

Designed for sealing absorbent or porous substrates (e.g. concrete, cement-asbestos,masonry) to be finished with a Chemor coating system.

AdvantagesDeep penetration combined with positive anchoring in the substrate assisted by its fluidity and high wetting power.

Provides positive bonding for epoxy finishes.


Priming-sealing of concrete, masonry, cement-asbestos or wood prior to the application of recommended 2-component epoxy finishes.


Both ambient and substrate temperature should be at least15°C during application and curing of the product. (curingtime is shortened by warm but prolonged by cold temperatures).




84 Tri-Tex co inc.

CONSTRUCTIONc










Directions for useNOTE: Any finish should be applied within a 24 hour intervalto the primed surface.

If not, scuff sand prior to the application of the finish.

MixUsing a non-sparking mechanical mixer blend thoroughly the mix of Parts A and B in the ratio indicated on the label.

ApplicationRoller, rubber squeegee, low pressure spray.

Rate of application is guided by product absorption by the substrate.

Do not pool.





85 Tri-Tex co inc.

CONSTRUCTIONc

Characteristics

Presentation two component product Parts A & B

Pot life 100 gram mass @ 21°C. 2 hours

Consistency creamy

Solids content 100%

Flash point >100°C

Coverage 2m2 to 4m2/l depending on the porosity of the surface.

Curing time (21°C)Dry to touch 8 hoursTo recoat 16 hours

Diluent & cleaning Solvent Chemor Solvent SV-40.

Storage minimum one year in original containers at 17°C-30°C.

Impact resistance (direct)(1-GP-71 method 147.1) 13.0 J minimum

Elongation minimum 4%(ASTM D-638)

Scrubability(1-GP-71,method 125.1) passes 10,000 cycles.

Water vapor transmission(ASTM E-96) 6.9ng/Pa.s.m2


Chemorclad 9200DescriptionCHEMORCLAD 9200 is a 100% solids, two component epoxyprimer-block filler which cures at ambient temperatures.

This products serves as an impermeable base coat for porous surfaces : concrete, concrete block, wall board, plywood, etc.For use on walls,floors and ceilings.

FinishingCHEMORCLAD 200, CHEMORCLAD 150 orCHEMORCLAD 130, epoxy top coats.

UsesWherever fully waterproof surfaces are required prior to the application of an epoxy coating.

For masticating pores and pinholes.

To form coves : wall/wall and wall/ceiling.

To laminate fiber glass at the joints of dissimilar materials.

The addition of fine silica sand assists in filling cracks andcavities.

LimitationsThis product is a vapor barrier.

Hydrostatic pressure must not exist behind treated surfaces.

Low temperatures prolong curing time.

For best results the ambient and surface temperatures should be at least 15°C during application and during initial curing.

New concrete should be cured at least 28 days and should not exceed 15% humidity.


86 Tri-Tex co inc.

CONSTRUCTIONc

SafetyProduct is combustible in the liquid state.

Keep away from flames and sparks.


Contact with skin could cause dermatitis.

Wear safety glasses and gloves.

Do not breath vapors.



If an irritation results, consult a physician.


Surface preparationThe surface must be sound, clean and dry.

Laitance, oil, grease, wax, rust and all other contaminantsmust be removed.

The surface should be free of curing membranesand sealers.

Directions for use

MixingSeparately mix Parts A and B prior to mixing them together in the ratio indicated on the containers.

To minimize air entrainment, a low speed (250 r.p.m.) electricmixer is recommended.

A homogeneous blend is usually obtained after 2-3 minutesmixing.

Do not mix larger quantities than can be applied before the expiration of the pot life.

ApplicationBrush, short nap roller, squeegee, spatula.

If the first finishing coat cannot be applied within 24 hours, it will be necessary to sand the surface of CHEMORCLAD 9200 prior to finishing, in order to assure a good intercoat adhesion.

Clean-upClean tools and equipment immediately after use, before theproduct has hardened, otherwise cleaning will be very difficult.


87 Tri-Tex co inc.

CONSTRUCTIONc

Characteristics

Presentation two-component product Parts A and B

Color pale orange

Volume solids content 75%

Pot life (Mix A +B) @ 21ºC;100g mass one hour

Number of coats usually one

Coverage 9m2/l @ 80 microns dry film thickness.

Curing time @ 21ºCTo touch 5 hoursTo recoat 12 hoursComplete 3 daysFor fresh concrete nontacky surfaceFor shotcreting overnight

Cleaner/Diluent Chemor Solvent SV-40.

Recommended Finishes epoxies, polyurethanes, alkyds.

Chemorclad 9600DescriptionTwo-component epoxy/polyamide pigmented anticorrosive primer for both ferrous and non ferrous metals.

AdvantagesExcellent adhesion to metals.

Flexible: coated steel can be bent to 90°

High chemical resistance.

Anti-corrosive pigmentation protects metal surfaces fromrusting.

Lead and chromate free.

UsesProtection of metal structures, equipment, machinery and also of concrete reinforcing steel.

Useful for spot-priming of damaged epoxy powder precoated rebars.

LimitationsMinimum application temperature of 10ºC.

Higher temperatures accelerate curing time, lower temperatures prolong it.

Surfaces to be primed must be clean and dry for optimum adhesion.


88 Tri-Tex co inc.

CONSTRUCTIONc

CleaningImmediately after use clean tools with Chemor Solvent SV-40.

Do not allow the product to harden, or it will be very difficult to remove.

SecurityFlammable in liquid state.




Surface preparationThe surface must be clean, dry and free of grease, oil or wax.

Clean with a steel brush or sandblast.

Ferrous metalsDegrease with a rag soaked in Chemor Solvent SV-40 or trichlorethylene.

Non-ferrous metals(e.g.galvanised, aluminium)Degrease and phosphatize at the same time with METPREP.

Directions for use

MixingMix each container separately (Parts A and B) before combining together in the proportions shown in the directions.

Add Part B to Part A, mix thoroughly.

ApplicationBrush, roller, spray.

Spray : reduce with a small quantity of Chemor Solvent SV-40

For best results apply at a wet film thickness of 50-80 microns (38-60 dry).


89 Tri-Tex co inc.

CONSTRUCTIONc

UsesExterior or interior.

Renovation, maintenance or new construction.

For use on surfaces not subjected to traffic.

A flexible and impermeable coating that breathes : for concrete structures and facades, concrete block, brick and stucco.

For residential and commercial buildings, institutions, columns, bridges, overpasses, retaining walls, etc.

RecommendationsWhen it is known that there could be accumulations of snow or deicing salts against the coated surface, prior to the application of CHEMORLAST, a coat of a silane water proofing sealer (CHEMORSEAL N-20) should be applied.

CHEMORSEAL N-20 should be applied to the maximum height of known snow and ice accumulation (columns,foundation or retaining walls, bridges etc.).

See separate technical data sheet for CHEMORSEAL N-20.

CHEMORLAST application can proceed the following day.

LimitationsBeing a water based product, it must be protected from freezing.

Surfaces to be coated must be sound, clean and free of allcontamination.

Not for recoating of finishes other than CHEMORLAST without prior consultation with CHEMOR Technical Service.

Do not apply on frozen surfaces.

Do not apply when there is a risk of rain or freezing or on overheated surfaces.

ChemorlastDescriptionCHEMORLAST is a ready to use one component product, based on an elastomeric acrylic aqueous dispersioncontaining pigments, mineral fillers and rheologicaladditives.

CHEMORLAST forms a protective and decorative film with exceptional elasticity and resistance to the elements.

Available in smooth or sand finishes.

TypesTYPE I SmoothTYPE II Medium SandTYPE III Coarse Sand or Simulated Stucco

Systems

Smooth Finish Type I (2 coats).

Sand FinishesMedium Sand Base Coat Type I (1 coat) Finish Coat Type II (1 coat)Course Sand or Simulated Stucco Base Coat Type I (1 coat) Finish Coat Type III (1 coat)

Advantages• Excellent adhesion and permanent elasticity.• Resists ultraviolet (UV) rays.• Lets the substrate breathe.• Bridges cracks and microfissures.• Excellent color retention.• Available in a variety of decorative colors.• Resists midew and fungus growth.

Primers & Coatings / Chemorlast

90 Tri-Tex co inc.

CONSTRUCTIONc

Clean-upwater for fresh product; xylene for dried product.

Package Stabilityone year in original unopened containers, protected from freezing.

Crack bridging(Determined by the total thickness of dry film of Type I)

Type 1Maximum width of crack

Dry film thicknessthat can be bridged

0,109mm 0,6 mm

0,136 mm 0,75 mm

0,1S2mm l,Omm

0,273 mm 1,5 mm

0,364 mm 2,0 mm

Physical properties (Type I)

Tensile Strength (ASTM D-412) @ 25°C 3 MPa @ 0°C 6 MPa @-18°C 14 MPa

Adhesion to concrete Excellent

Elongation (ASTM D-412) @ 25°C 670% @ 0°C 550% @-18°C 150%

Flexibility/Type II (2.5cm mandrel @ 23°C) Passes

Permeability to water vapor(ASTM E-96) @ 0.5mm dry film 5.2 metric perms (8 perms).

Freeze-thaw resistance Very good

The minimum ambient and surface temperature for application is 7°C, during application and for at least 18 hours following.

Do not use on surfaces that will be subjected to traffic.

Characteristics

Presentation Single component, pigmented, water based product.

Number of coats Two minimum.

FinishesTYPE I Smooth and matt.TYPE II Medium sand; matt.TYPE III Coarse sand or simulated stucco; matt.

Colors Available in colors shown on Chemor Color Card«Wall Finishes». For custom colors consult Chemor Customer Service Dept.

ViscosityTYPE I 1100-1200 mPa.s.TYPE II 2300-2600 mPa.s.TYPE III 3500-3800 mPa.s.

Solids Content

Weight Volume

Type I 73 % 51 %

Type Il 85 % 64 %

Type IlI 87 % 67 %

Drying TimeTo Touch 1 hourTo Recoat Over night (15 hours)

Flammability Non-flammable


91 Tri-Tex co inc.

CONSTRUCTIONc

Guide to Application

Type I : SmoothType II : Medium sandType III : Coarse sand or simulated stucco

1st Coat Type I

Method Roller 30 mm pile

Coverage 4.9 - 3.3 m2/l.

Film Thickness

Wet 0,20 mm - 0,32 mm

Dry 0,10 mm - 0,16 mm

2nd Coat Type I Type II Type II Type III

Method Roller 30mm pile

Roller Hopper gun

Hopper gun

Coverage 4.9-3.3m2/l 4.9-3.3m2/l 3.5-2.6m2/l 1.3-.65m2/l

Film Thickness

Wet 0.20-0.32mm

0.20-0.32mm

0.28-0.38mm

0.79-1.52mm

Dry 0.10-0.16mm

0.13-0.20mm

0.18-0.24mm

0.53-1.03mm

Clean-upClean up material with water immediately after use.

SecurityUse with adequate ventilation.

Avoid contact with eyes or skin.



Resistance to weathering Very good

Resistance to mildew and fungus growth Very good

Surface preparationThe surface must be sound, solid and free from laitance, grease, oil, rust, paint, sealers, dust or any other material which could detract from the adhesion of CHEMORLAST.

Cavities, holes or irregularities should be masticated or filled with CHEMORTOP 422 or 423 mortars.

Hairline cracks that are stable can be masticated or filled with CHEMORLAST Type I applied by brush.

ApplicationBrush, roller, hopper gun (see Table «Guide to Application».)Mix well before and occasionally during use. Do not reduce.Allow to dry through before recoating.

System : smoothApply two coats of Type I.

System : medium sandBase Coat Type I.Top Coat Type II.

System : coarse sand or simulated stuccoBase Coat Type I.Top Coat Type III.


92 Tri-Tex co inc.

CONSTRUCTIONc

Do not apply CHEMORDUR 25 to :• Lightweight, very porous cement based materials.• Surfaces previously treated with curing agents, sealers,

coatings, unless they have been removed to bare concrete by chemical or mechanical means.

• Colored concrete can only be treated after a full cure.• Do not get on glass, metal or other finished surfaces. If

so, flush immediately with water to prevent permanent staining.

Characteristics

Physical form Clear, colorless liquid.

Carrier Water

Flash point None

VOC (g/L) 0

Specific gravity 1.20 ± 0.5.

ACI 302Class 1 to 4 Concrete floors.Class 9 Super flat floors.

Coverage1st coat approx. 5.0m²/L.2nd coat approx.10.0m²/L.

Application temperature 4°C.to 40°C.

Film none.

Penetration depth 3± 0.5mm. (high density concrete)

Skid resistance Good.

Chemordur 25DescriptionCHEMORDUR 25 is a colorless, liquid applied concrete hardening and dustproofing treatment.

The product is water-based and odorless.

CHEMORDUR 25 effectively penetrates the surface and solidifies the concrete components by chemical reaction.

This results in increased density, hardening, toughening andsealing of the surface to optimize the resistance to vehicular and foot traffic.

The treatment is as permanent as concrete itself.

Advantages• Removes free lime and excess alkali from concrete

surface.• Non-toxic, odorless, nonflammable, non-combustible :

ideal for food storage & distribution, processing and retail facilities.

• Dustproof easy to maintain.• Permits water vapor transmission («breathing»).• Good chemical resistance.• Does not alter the color of concrete.• Excellent color retention (non-yellowing).

UsesHardening, dustproofing of concrete floors subjected to vehicular and heavy foot traffic : food warehouses, distribution centers, processing plants, canning factories, breweries, bakeries, super-markets, etc.

LimitationsProtect from freezing.

CHEMORDUR 25 is not a concrete curing agent.

Sealers / Chemordur 25

93 Tri-Tex co inc.

CONSTRUCTIONc

Remove all residues, tire marks, oil, sealers, coatings,laitance and contaminants to ensure deepest penetration and chemical reaction of CHEMORDUR 25.Acid etching is not recommended.Repair all cavities, holes,dete-riorated areas, cracks and joints. Refer to CHEMORTOP cement-polymer mortars, CHEMORPATCH 66 epoxy mortar, CHEMORSET 400 NS/SL joint fillers, CHEMORSET 100M epoxy binder).

NOTE: CHEMORDUR 25 will not hide different colors on the concrete surface nor provide floor leveling. For appropriatetreatment of very porous, worn or stained surfaces, contact Chemor technical representative for assistance.

ApplicationFollow the same procedures as for New Concrete (see above).

Covering of chemordur 25 treated floorsFor coating applications, surface preparation may require chemical or mechanical etching.

Test sample for adhesion is recommended for best results.

Common tiling adhesives are compatible with treated surfaces.

MaintenanceOn smooth-troweled concrete, a sheen develops within several months.

Maximum performance and life expectancy are assured by good housekeeping practices such as regular sweeping, washing, wet mopping with mild detergent, mechanical scrubbing.

Safety• CHEMORDUR 25 is an alkaline solution.• Avoid contact with eyes and skin.• Wear safety glasses, protective gloves and clothing.• Refer to Material Safety Data Sheet.

Chemical resistance*

Alcohols, aldehydes,amines, esters,detergents, hydrocarbons,hydraulic fluids, naturalfats and oils, oils andfuels.

no effect

Diluted acids, alkalis &salts

no effect

*Detailed data on specific chemicals is available on request.

InstallationApplication by lambs wool pads, mop, roller, low pressure spray.

New concrete surfaceAfter final troweling apply a flood coat at the rate of 5m²/L. Scrub into the surface with a motorized mechanicalscrubber or stiff broom.This will assist to achieve maximum penetration. Continue scrubbing or brooming for 30-45 minutes. When product begins to thicken, sprinkle with water and scrub or broom for another 10-15 minutes.Flush off any excess of residual product with clean water and remove all liquid from the floor by squeegee and wetvacuum.Being non-toxic, all this residue can be emptied into a sanitary sewer.Porous or rough textured surfaces may require a second application which can be installed as soon as the first one becomes dry, or any time thereafter. Floor is available for occupancy as soon as it becomes dry (3-4 hours @ 21°C.).

NOTE: Failure to flush off and remove all excess material may produce unsightly white stains.

Existing hardened concrete surface

Surface preparation:Must be structurally sound and clean.

Sealers / Chemordur 25

94 Tri-Tex co inc.

CONSTRUCTIONc

LimitationsFor maximum penetration apply to dry surfaces.

Not recommended for filling visible cracks.

Not recommended for asphalt or painted surfaces.Minimum ambient application temperature of 5°C.

The product may darken colors of some substrates.

A preliminary test application is recommended.

Characteristics

Presentation One component liquid.

Color Clear, colorless.

Gloss Low to medium depending on porosity of surface and number of applications.

Solids content (by weight) 10%

Flash point Nil

Color retention Excellent (non-yellowing)

Alkali resistance Very good.

Water vapor transmission(ASTM E-96) Breathes.

Coverage (approximate, depending on porosity of the substrate)

Common brick 2-3m2/l.Dense brick 2.8-4.2m2/l.Precast concrete 2.5-3.3m2/l.Concrete block 1.8-2.8m2/l.Cement stucco 2.2-3.3m2/l.

Chemorseal AW 10DescriptionCHEMORSEAL AW-10 is a clear, water based acrylic sealer designed for dustproofing and moisture-proofing of mineral surfaces.

Specially formulated system enhances deep penetration into substrates, providing long lasting surface and subsurface protection.

It accentuates colors and brilliance of exposed aggregatesand mineral substrates.

Without being a vapor barrier, CHEMORSEAL AW-10 minimizes water absorption and intrusion of atmosphericpollutants.

Sealed surfaces are protected against freeze-thaw, acid rain and soiling.

AdvantagesEnhances the colors of aggregates and the appearance of exterior walls and facades.

Excellent color retention (nonyellowing).

Resistant to water, acid rain, cleaning products and alkalis.


Protection of facades, walls and ceilings in brick, concrete, concrete block, prefabricated concrete panels, stone, wood; concrete floors and terrazzo.

Sealers / Chemorseal AW 10

95 Tri-Tex co inc.

CONSTRUCTIONc

SafetyRefer to Materials Safety Data Sheet(MSDS).

Drying time @ 21°C.To recoat 2 hours

Cleaner Water for fresh product

Shelf life minimum one year in original sealed containers at 30°C. max.

Protect from freezing

Directions for useNOTE: to ensure satisfactory results, a prior test applicationshould be performed.

Surface preparationthe surface should be clean and sound.

Dry surfaces allow maximum penetration.

All efflorescence and apparent surface alkalinity should beremoved and/or neutralized.

No priming is needed.

ApplicationBrush roller or low pressure spray.

The number of applications depends on the porosity of thesurface.

Saturate the surface without leaving an excess.

Allow it to dry before applying another coat.

Adjacent non-treated surfaces and vegetation should be protected from splashes and over-spray.

To test damp-proofness, allow last coat to dry for 48 hours and subject sealed surface to a water jet under moderate pressure.

The color of the sealed surface must not darken for an effective dampproofing.


96 Tri-Tex co inc.

CONSTRUCTIONc

Characteristics

Presentation Single component liquid.

Specific gravity 1.03

Solids (by weight) 25%

Flash point nil

Water retention conforms to ASTM C-309, Type I.

Application method brush, roller, spray.

Number of coats One or two for porous surfaces.

Color retention Excellent (non-yellowing).

Coverage 6-10m2/l (approximate, depending on porosity of the substrate).

Drying timeTo recoat 4 hours.For traffic 16 hours.

Cleaner Water for fresh product.

Shelf life Minimum one year in original sealed containers.

Chemorseal AW 25DescriptionCHEMORSEAL AW-25 is a clear, water based acrylic sealer.

It is designed for penetration into and sealing of mineral surfaces such as masonry and concrete, etc.

It is also useful as a curing membrane for fresh concrete.

TypesType I clear, colorless.Type II colored

AdvantagesExcellent adhesion to fresh or hardened concrete.

Resistant to wear and traffic.

Efficient dustproofing, waterproofing, and against stainprotection.

Excellent color retention (non-yellowing).

Pigmented version available.


Curing and sealing of concrete floors.

Sealing of masonry, unistone pavers and other porousmineral surfaces.


97 Tri-Tex co inc.

CONSTRUCTIONc

SafetyRefer to Material Safety Data Sheet (MSDS).

Direction for useNOTE: Do not apply in temperatures lower than 10°C.

Curing membrane / fresh concreteAs soon as initial set has been achieved, apply one uniform coat.

A second coat can be applied as a sealer at any time when moisture content in concrete is less than 19%.

Sealer / hardened concretesurface preparationThe surface should be sound and free of all contamination such as grease, oil, paint, tire marks, etc,.

Washing with detergent, acid etching or mechanical abrading is required.

ApplicationUniformly apply at least two coats depending on the porosity of the surface.

Do not puddle.


98 Tri-Tex co inc.

CONSTRUCTIONc

Ambient and concrete temperature of at least 15°C.during application and curing of the sealer.

Concrete surface must be free from curing membranes, sealer, paints or any other treatments or contaminants.

Could be incompatible with some sealants and caulkings. A test for suitability should be performed.

Light superficial chalking and yellowing due to weathering.

Characteristics

Presentation2-component liquid Parts A and B

Color Transparent straw-yellow.

Pot Life 8 hours.

Viscosity @ 21ºC 120 ± 10 mPa.s

Solids content 50% (by weight) 44% (by volume)

Flash Point 21.1°C.

Coverage 4.6-5.5m2/l./application (depending on concrete porosity).

Curing Time @ 21°C.Touch dry 6 hrsTo recoat 16 hrsVehicular traffic 24 to 36 hrs

Cleaner & Diluent Chemor Solvent SV-40

Shelf Life Min. one year in original packaging stored at 10-26°C.

Chemorseal EDescriptionCHEMORSEAL«E» is a penetrating 2-component clear sealer curing at ambient temperature.

Dustproofs, moistureproofs and protects hardened concrete against ingress of common aggressive chemicalsincluding deicing salts.

AdvantagesDeep penetration due to low viscosity.

Fills pores in concrete and as a result improves resistance to abrasion from vehicular traffic.

High resistance to deicing salts, gasoline, motor oil and chemical products (unlike conventional sealers, eg., acrylics, lineed oil,etc.).

UsesNew or old concrete: interior or exterior.

Concrete deck and floor protecion from freeze-thaw exposure, damages by chemicals, steel corrosion by chloride ions derived from deicing salts.

On all concrete surfaces that are periodically exposed to water and water containing dissolved chemicals, eg., deicing salts.

Protects all types of concrete : poured in place,prefabricated, prestressed, concrete block.

Typical applications include industrial floors, warehouses,workshops, garages, bridge decks, sidewalks.

LimitationsNew concrete must be cured for least 28 days.

Maximum moisture content in concrete of 15%.

Sealers / Chemorseal E

99 Tri-Tex co inc.

CONSTRUCTIONc


Keep away from excessive heat, flames and sparks.


Ensure an adequate ventilation.


In case of contact, wash with soapy water and rinse with clean, clear water.

If irritation occurs, consult a physician immediately.

Refer to Materials Safety Date Sheet (MSDS).

Surface preparationConcrete should be sound, dry and cured for at least 28 days.

The surface must be free from grease, oil, laitance, curingmembranes, sealers, tire rubber marks, dust or any other contaminant impairing good penetration of Chemorseal «E». For thorough cleaning use chemical or mechanicalmeans.

Directions for use

MixingUse a slow speed non-sparking electric drill to blend Parts A and B in the prescribed volume ratio.

Allow the mix to rest for 45 minutes (induction period)prior to its application.

ApplicationRoller, squeegee or low pressure spray.

Use absorption into concrete as an application guide.

Avoid puddling.

If a second application is required, wait until the first one has cured, but not beyond 24 hours.

Any mixed product remaining at the end of the working day should be discarded in compliance with environmentprotection guidelines.

Equipment and tools should be cleaned with Chemor Solvent SV-40 before the product has hardened.

Sealers / Chemorseal E

100 Tri-Tex co inc.

CONSTRUCTIONc

Improves freeze/thaw resistance.

Reduces efflorescence.

Is not a vapor-barrier : allows equilibration of water vaporpressure across walls(breathing).

UsesNew construction, restoration or renovation of existing buildings and structures.

Colorless water-repellent treatment for absorbent mineral surfaces exposed to rain and aggressive atmospheric agents.

Architectural concrete.

Bricks (clay or calcium silicate).

Mortars, stuccos.

Prefabriqued concrete panels.

Silica containing stones.

LimitationsA prior test application is recommended to establish the effectiveness of the treatment.

Do not apply over very humid or saturated surfaces.

Not recommended as a waterrepellent for below grade.

Not recommended for sealing cracks apparent to the eye.

Not recommended over painted surfaces.

Do not apply at temperatures below 3°C., and do not expose treated surfaces to such temperatures for 10 hours following application.

Chemorseal N 20DescriptionCHEMORSEAL N-20 is a single component penetrating silane moistureproofing for concrete structures, parking decks, buildings : architectural concrete and masonry.

CHEMORSEAL N-20 is not a surface coating:it penetrates deeply and chemically reacts with silica containing substrates to form permanent bonds.

Thus the problem of lifting, scaling, and eventually debonding of the coating film due to moisture infiltration is avoided.

The sealer is a clear, colorless liquid which does not change the color of most substrates.

It is not a vapor-barrier.

CHEMORSEAL N-20 reduces the penetration of water and chloride ions (deicing salts), protecting reinforcing steel against corrosion.

AdvantagesSimplicity and economy of use.

Does not change of the appearance, the color and texture of most sealed surfaces.

Significant reduction of capillary penetration of water and of water soluble aggressive substances (e.g. acid rain).

Major reduction of chloride ion penetration (deicing salts) :protects reinforcing steel.

Reduces penetration of air pollutants (soiling).

Upgrades the appearance of facades and of exterior walls.

Sealers / Chemorseal N 20

101 Tri-Tex co inc.

CONSTRUCTIONc

Surface preparationThe surface must be sound and clean.


Penetration can be improved by a light sandblasting of thesurface.

Old concrete must be free of any curing membrane, grease, oil, paint,etc.

ApplicationUse product as delivered (do not dilute).

Low pressure spray, brush, or roller, applied to saturation ofthe surface.

The number of applications depends on the porosity of thesurface. It is advisable to coat a test area to determine theexact coverage of CHEMORSEAL N-20 required for effective waterproofing.

Non-treated adjacent surfaces should be protected againstspillage and overspray.

SafetyFlammable liquid due to volatile solvents.


Avoid skin contact.

Wash hands thoroughly after each use.

If there is contact with : Eyes : wash profusely with clear water.Skin : wash with soapy water.


Characteristics

Presentation Very fluid clear liquid.

Color Colorless.

Flash Point 40ºC.

Coverage depend on substrate porosity 2.5m2-5.0m2/l.

Cleaner Mineral spirits.

Shelf life 6 months in original unopened containers, stored at 10- 28°C.

Typical performancecomplies with the requirements of #244 study National Cooperative Highway Research Program U.S.A. : at least 75% reduction of water and chloride ion absorption.

On concrete Sealed with Chemorseal N-20

Untreatedcontrol

Absorbed water ( % weight)

0.45 2.67

Reduction absorbed water (%)

83.2 ----

Absorbed chloride (% weight)

0.023 0.255

Reduction absorbed chloride ion (%)

90.0 ----


102 Tri-Tex co inc.

CONSTRUCTIONc

Uses• Parking garages.• Bridges.• Roads.• Architectural concrete.• Bricks (concrete containing).• Mortars, stucco.• Silica containing stones.• Other horizontal and vertical surfaces.

LimitationsA prior test application is recommended to establish the effectiveness of the treatment.

Do not apply over very humid or water saturated surfaces.

Not recommended as a waterrepellent for below grade.

Not recommended for sealing cracks apparent to the eye.

Not recommended over painted surfaces.

Do not apply at temperatures below 3°C., and do not expose treated surfaces to such temperatures for 10 hours following application.

Characteristics

Presentation single component, very fluid, clear liquid.Color colorless.

Solids content 40% (by weight).

Flash point 40ºC

Coverage Depends on surface porosity 2.5m2-6.0m2/l.Concrete 4.5-6.0m2/l. on average.

Chemorseal N 40DescriptionCHEMORSEAL N-40 is a single component, solvent containing, silane based sealer, designed to give deep penetration into the pores of mineral surfaces such asconcrete and masonry.

CHEMORSEAL N-40 is not a surface coating : it penetrates deeply and chemically reacts with silica containing substrates to form permanent bonds.

Thus the problem of lifting, scaling, and eventually debonding of the coating film due to moisture infiltration is avoided.

AdvantagesSimplicity and economy of use.

Does not change the appearance, the color or texture of most sealed surfaces.

Significant reduction of capillary penetration of water and of water soluble aggressive substances (e.g. acid rain).

Major reduction of chloride ion penetration (de-icing salts):protects reinforcing steel.

Reduces penetration of air pollutants (soiling).

Upgrades the appearance of facades and of exterior walls.

Improves freeze/thaw resistance.

Reduces efflorescence.

Is not a vapor-barrier : allows equilibration of water vaporpressure across walls (breathing).


103 Tri-Tex co inc.

CONSTRUCTIONc

ApplicationUse product as delivered (do not dilute).

Low pressure spray, brush, or roller, applied to saturation ofthe surface.

The number of applications depends on the porosity of the surface.

It is advisable to coat a test area to determine the exact coverage of CHEMORSEAL N-40 required for effective waterproofing.

Non-treated adjacent surfaces should be protected againstspillage and overspray.

SafetyFlammable liquid due to volatile solvent.


Avoid skin contact.

Wash hands thoroughly after each use.

If there is contact with :Eyes : wash profusely with clear waterSkin : wash with soapy water.


Drying time 16 hours @ 15-30°C. before opening to traffic.

Cleaner mineral spirits.

Shelf life 12 month in original unopened containers, store at 5-30°C.

Packaging units of 20 l. and 205 l.

Typical performanceComplies with the requirements of #244 study of the National Cooperative Highway Research Program (U.S.A) when applied at a rate of 3m2/l.:

Reference Penetration in concrete (mm)

Reduction of absorbed water (%)

Reduction of absorbed chloride ion (%)

Chemorseal N-40

6 87 94

#244 requirement

---- 75 75

Directions for use

Surface preparationThe surface must be sound and clean.


Penetration can be improved by a light sandblasting of the surface.

Old concrete must be free of any curing membrane, grease, oil, paint, etc.


104 Tri-Tex co inc.

CONSTRUCTIONc

UsesIt is used on concrete new construction and restoration.

It is used as a colorless water repellent treatment on all absorbent mineral surfaces exposed to rain and harsh weather.

It is used to:• Architectural concrete• Brick silicate, calcium or clay• Mortar• Plaster• Precast concrete panels• Rocks containing silica

Procedures

Surface PreparationThe surface must be sound, free of oil, grease, rust, wax, curing membrane, sealer or other contaminants such as puddles. The minimum temperature must be at least 3 ° C during application or within 10 hours after application.To clean the surface, you can perform a washing detergent or muriatic acid etching. You can also clean the surface by mechanical stripping. A preliminary test should be conducted to ascertain the effect of treatment.The Chemorseal N 100 is not recommended as a waterproofing below ground level. It is not recommended either for sealing cracks visible to the naked eye.

MixingMix Chemorseal N 100 before application.

EstablishmentN 100 Chemorseal Apply by brush, roller or low pressure sprayer until the bottom is saturated. The number of applications depends on the porosity of the bottom. We recommend a trial application to determine the yield of N 100 Chemorseal required for effective sealing of the substance to be considered. Untreated adjacent surfaces must be protected against splashes.

Chemorseal N 100DescriptionThe Chemorseal N 100 is a silane compound at 100% solids, which increases the penetration into the pores of the mineral surfaces to be sealed.

The Chemorseal N 100 penetrates deeply and acts chemically with the substrates containing silica to create a permanent bond.

This avoids the problems of lifting film coatings caused by water infiltration.

In addition, it protects the reinforcing steel against corrosion by reducing the penetration of water and chloride ions from deicing salts.

Features and BenefitsIt does not cut the steam and breathe well, allowingequilibration of water vapor.

It preserves the color of the treated surface.

It reduces the penetration:• Capillary water• Aggressive agents soluble in water such as acid rain• Chloride ions such as deicing salts• Soil

It enhances the appearance of the facades of the exterior walls.

It improves resistance to freezing and thawing.

It reduces efflorescence.


105 Tri-Tex co inc.

CONSTRUCTIONc

CleaningTools and equipment should be cleaned with mineral spirits while Chemorseal N 100 is still fresh.

Once hard, it comes off very easily.

SafetyIn liquid form, this product is flammable.

It should be kept away from flame and heat sources.

Furthermore, it should be used in a well ventilated area.

A prolonged or repeated contact may cause irritation of the skin, eyes and respiratory tract.


Wearing gloves, goggles and protective clothing is recommended.

Things whether it is in contact with skin, wash immediately with water soapy.

Things whether it is irritation, rinse thoroughly for at least 15 minutes and seek medical attention immediately.


Technical Data

Typical PerformanceAccording to the NCHRP # 244 USANational Cooperative Highway Research ProgramApplication rate = 3 m 2 / I.

Penetration into the concrete 6 mm

Reduced water absorption 87%NCHRP requirement # 244 75%

Reduced absorptionthe chloride ion 94%NCHRP requirement # 244 75%

Solids content 40%

Flashpoint 40 °C

Curing time @ 21 °CReady for traffic 16 hours

PerformanceThe yield of Chemorseal N 100 is 2.5 m 2 / I. 6 m2 / I.,depending on surface porosity.

PackagingThe Chemorseal N 100 is packaged in containersmetal. The weight of shipping units is 17.9 kg in containers ranging from 18.92 l. to 208 l.

Storage and Shelf LifeIn its original packaging, the Chemorseal N 100 can be stored for 1 year at a temperature between 5 °C and 30 °C. Color Colorless and transparent


106 Tri-Tex co inc.

CONSTRUCTIONc

UsesConcrete new or old : interior.

For sealing of hardened concrete to protect against damage caused by freeze-thaw, erosion, corrosion and delamination due to chloride ions.

On all concrete surfaces that are periodically exposed to water and water containing dissolved chemicals,eg., deicing salts.

Protects all types of concrete :• Poured in place• Prefabricated prestressed• Concrete block.

Typical applications include industrial floors, warehouses,workshops, garages, bridges decks, sidewalks.

LimitationsDo not apply on concrete if its humidity exceeds 15% nor on concrete that has cured for less than 28 days.

Ambient temperature and that of the concrete should be at least 10°C.

Could be incompatible with some sealants and caulkings.

A test for suitability should be performed.

This product reacts with atmospheric humidity, keep the containers tightly closed when not in use.

Some yellowing can occur when coated surfaces are exposed to U.V. (sunlight).

Chemorseal PDescriptionCHEMORSEAL P is a transparent or colored penetrating polyurethane sealer.

The product cures by reacting with atmospheric humidity at ambient temperatures.

The product seals hardened concrete protecting it against penetration of water and chloride ions.

It equally is an effective durable dustproofing treatmentfor concrete floors.

TYPE I Clear on-component.TYPE II Colored two-component.

AdvantagesNOTE: Drying time can be shortened by about 50%(see «Characteristics»).

Deep penetration due to its low viscosity.

Fills the pores of concrete and thus enhances resistance to abrasion from vehicular traffic.

High resistance to deicing salts, gasoline, motor oil and chemical products.

Economical. Easy to apply.

Sealers / Chemorseal P

107 Tri-Tex co inc.

CONSTRUCTIONc

Surface preparationThe concrete must be sound, dry and have cured for at least 28 days.

It must be free from oil, grease, laitenance, curing membranes, paint, sealers, rubber tire marks, dust and all other contaminants to allow ensure a good penetration.

For thorough cleaning use chemical or mechanical means.

Directions for useNOTE: To shorten drying time, add before use, ACCELERATOR «P» at ratio of 500 mL per 18.92 L pailand mix well.

Low pile roller, rubber squeegee, low pressure spray.

Adjacent non-treated surfaces should be protected from splashes and overspray.

For the first application dilute the product with solventSV-22 according to the porisity of concrete.

Do not puddle.

Be guided by the absorption of the concrete.

For the second application wait until the first coat has cured, but do not exceed 24 hours.Clean all tools and equipment with Chemor solvent SV-22 before the product hardens.

SafetyFlammable liquid.

Keep away from excessive heat, open flames, sparks.

Do not inhale vapors.


See Material Safety Data Sheet.

Characteristics

Presentation liquid product.

Color colored two-component transparent one component.

Viscosity 110 ± 10 mPa’s @ 21°C.

Solids content 42-45% (by weight) depending on color.

Flash point 28 °C.

Average coverage for 2 applications 6-7m2/L/coat.

Dry film thickness approx. 62 microns (2.5mils)/coat.

Drying time @ 21°C./50% R.H. (hours)

As is Accelerated

To touch 4 2

To recoat 4-6 2-3

For vehicular traffic 16-24 8-12

Cleaning solvent Chemor Solvent SV-22.

Storage minimum of one year in original unopened container, when stored at 3-26°C.

Sealers / Chemorseal P

108 Tri-Tex co inc.

CONSTRUCTIONc

AdvantagesSeamless and impermeable.

Hard and resistant to heavy traffic while maintaining adegree of flexibility.

Ready for traffic 48 hours after installation.Thin and light weight.

Chemical resistance (note: the chemical resistance of theaggregate should be considered separately).

Does not support microbial growth.

Can be applied to cove bases and plinths to seal the jointsbetween floors and walls.

Melds with the level of adjacent surfaces.

Damaged areas can be easily repaired.


UsesFor interior use on floors, stairs, bases and plinths.

Especially suitable for public buildings, washrooms, halls,restaurants, shopping centers, etc.

Ideal for renovation work in view of its low thickness andits rapid and easy installation.

Chemoraz EDescriptionCHEMORAZ «E» is a two component, seamless epoxy flooring.

Curing takes place at ambient temperature.

This is a 100 % solids material containing epoxy resins,hardeners and flexibilizers to which is added selected aggregates of marble, granite or other resistant material.

CHEMORAZ «E» is applied by trowel, in a paste consistency,to concrete or rigidly fixed plywood.

After initial hardening (16-24 hrs.), the surface is polished with a terrazzo grinder to obtain a thickness of 6.3 to12.6mm, as required.

TypesThe epoxy binder is available in a choice of standard colors (see Chemor color card).

Special colors are available on request.

The standard aggregate sizes are No. 0 and 1.

Marble most commonly used.

For greater resistance and for use in acid environments granite aggregate can be used, at a cost premium.

FinishesSmooth - surface sealed.

Seamless floors / Chemoraz E

109 Tri-Tex co inc.

CONSTRUCTIONc

Surface preparationThe level of the sub-floor must be 6.3mm or more below the level of the terrazzo finish.

The concrete must be a minimum of 20.7 MPa, water cured and finished by steel trowel.

The use of a curing membrane is not permitted because of its adverse effect on adhesion.

Before installing CHEMORAZ «E», the concrete must be roughened mechanically or chemically.

It should then be washed with clean water and allowed to dry.

The concrete should be sound, clean, and free from oil, grease and all other contaminants.

Plywood should be exterior grade, good one side, and of minimum thickness of 18.7mm.

It should be solidly fixed in place with rustproof screws.

The joints of 6.3mm (max.) should be filled with epoxy mastic CHEMORSET 400 NS.

LimitationsAmbient temperature and temperature of the sub-floor must be at least 13°C. during application and for the following seven days.

Not to be applied on sub-floors whose humidity surpasses 15%.

The product containing marble chips is not recommended for acid environments.

Not recommended for continuous service at temperatures above 55°C.

Cracks in the concrete slab can be transmitted to the surfaces.

WaterproofingFor complete waterproofing, a coat of elastomeric waterproofing membrane CHEMORFLEX 300 should beapplied prior to CHEMORAZ «E» application (optional).

Companion productsPrimer, transparent sealer, cleaning solvent : as recommended by CHEMOR INC.

MaintenanceIf desired, a thin coat of wax can be applied.

Sweep, damp mop, wash with water and a milddetergent.


110 Tri-Tex co inc.

CONSTRUCTIONc

SecurityProducts are combustible in the liquid state.


Avoid contact with the eyes and skin.Skin contact could cause dermatitis.

Wear safety glasses and protective gloves and protective clothing.


Characteristics


Properties Test Result

Compressive strength

ASTM C-579 80 MPa

Tensile strength (binder only)

ASTM D-307 18 MPa

Flexural strength ASTM C-580 34 MPa

Bond strength AASHTO T-237 2.5MPa (100%failure in concrete)

Water absorption ASTM C-570 0.1%

Thermal coefficient of linear expansion

ASTM E-831 2.5X10-6/mm/mm/°C.

Flammability ASTM D-635 Self-extinguishing

Weight at 6.3mm thickness

12.7kg/m2 (average)

Chemical resistanceASTM D 1308 Covered, 5 days.

Reagent Result

Vegetable and animal oils, grease, gasoline, salt, water, sugar, urine, sodium hypochlorite (bleach), aliphatic hydrocarbons, fruit juices, alkali, detergents

Unaffected

Dilute acids -product with marble chips

Attacked

Dilute acids -product with granite chips

Resistant


111 Tri-Tex co inc.

CONSTRUCTIONc

AdvantagesSeamless, sanitary, impermeable, tough, durable.

Thin, light weight.

Can be applied to cove bases and plinths to seal the joints between floors and walls.

Hard, resistant to heavy traffic.

Dust free.

Resistant to microbial growth(approved by Agriculture Canada).

Solid adhesion to concrete, plywood and steel.

Resistant to alkalis, dilute acids and a variety of aggressivechemicals.

Rapid installation.

Can be put back into service 24 hrs. after completion.

Damaged areas can be easily and quickly repaired.

Available in a variety of colors.


Floors, stairs, plinths.

Showers, cloak rooms, toilets, kitchens, halls, work shops.

Hospitals, schools, food processing plants, beverage bottling plants, pharmaceutical plants, electronics manufacturing, penitentiaries.

ChemorocDescriptionCHEMOROC is a two component, epoxy based seamless coating for floors.

Curing takes place at ambient temperatures.

This is a 100% solids material containing epoxy resin,hardeners, flexibilizers, and mineral pigments.

Aggregates to be added can be silica sand, aluminium oxide, carborundum, etc.

CHEMOROC mortar is applied by trowel to a thickness of 3mm to 6mm, depending on the nature of the subsequent traffic, It provides a tough, seamless, impermeable surface with excellent resistance to traffic and common chemicals.

The fluidity of CHEMOROC mortar can be easily adjusted by the amount of aggregate added depending on the use,eg., levelling, repair of damaged surfaces, making slopes.

ThicknessLight traffic 3 mm.Heavy traffic 6 mm.

ColorsAvailable in standard colors on CHEMOR color selector.Special colors available on demand.

Finishes«Orange Peel» or anti-skid.

Seamless floors / Chemoroc

112 Tri-Tex co inc.

CONSTRUCTIONc

Surface preparationThe surfaces of the sub-floor must be sound, solid dust-free and have the proper slopes.

The surfaces must be free of cavities and holes and all grease, oil, wax or any other material that could impair adhesion must be removed.

New concrete should be water cured.

Curing membranes must not be used.

Before installing CHEMOROC the concrete must be roughened mechanically or chemically.

Moisture content of the sub-floor must not exceed 15%.

ApplicationSee CHEMORDECOR, CHEMOROC and CHEMORQUARTZ Installation Bulletin.

MaintenanceSweep, damp mop, wash with water and a mild detergent.Worn and damaged surfaces can be easily and quickly repaired.

LimitationsSurfaces to be coated must be at least 15°C.

Temperatures during application and for a period of 18 hrs. following application must be 15°C minimum.

Relative humidity during this same period must not exceed 80%.

Surfaces to be coated should be sound, rigid, clean and dry.

An effective vapor barrier is required under surfaces on grade.Cracks in the concrete slab can be transmitted to the surface.

During application and curing of CHEMOROC in locations where food products are processed or stored, adequate ventilation must be provided to prevent contamination ofthe food (taste,odor, etc.) by volatile constituents in the coating.

Can be exposed to short intervals of temperatures up to 60°C.


WaterproofingFor complete waterproofing coat of elastomeric waterproofing membrane CHEMORFLEX 300 should be applied prior to CHEMOROC application (optional).


113 Tri-Tex co inc.

CONSTRUCTIONc

Chemical resistanceASTM D 1308Covered, 5 days

Reagent Result

3% acetic acid (vinegar), 5% citric acid,5% lactic acid, 20% sodium chloride,5% sodium hypochlorite, saturated solution of sodium carbonate or bicarbonate, 40% caustic soda, 25% potash, commercial detergents, butter, milk, coffee, gasoline, grease and mineral oil, mineral spirits, denatured alcohol, urine, oxygenated water.

Unchanged

10 and 50% Phosphoric acid, 10 and 35% Hydrochloric acid, 10% Nitric Acid, 10% Sulfuric Acid, Xylene

Unchanged







Characteristics




ASTM C-579 80 MPa.

Tensile Strength ASTM C-307 18 MPa.

Flexural Strength ASTM C-580 34 MPa.

Bond Strength AASHTO T-237 2.8MPa. (100% concrete failure)

Abrasion Resistance (Taber Abrader, CS-17 Wheel, 1000g load,1000 cycles)

ASTM D-4060 0.1g. max. loss

Hardness (SHORE D)

ASTM D-2240 86

Water Absorption ASTM D-570 0.1%

Thermal Coefficient of Linear Expansion

ASTM E-831 2.5X10-6/mm/mm/°C.

Flammability ASTM D-635 Self-Extinguishing



Weight of mortar @ 6mm thick

Approx 11kg/m2.


114 Tri-Tex co inc.

CONSTRUCTIONc

Solid adhesion to concrete, plywood and steel.Resistant to alkalis, dilute acids and a variety of aggressivechemicals.Damaged areas can be easily and quickly repaired.

UsesInterior or exterior.Floors, stairs, plinths.Showers, cloak rooms, toilets, kitchens, halls, work shops.Hospitals, schools, food processing plants, beverage bottling plants, pharmaceutical plants, electronics manufacturing, penitentiaries.

LimitationsSurfaces to be coated must be at temperature of at least 5°C. during application and for a period of 14 hrs. following application.Relative humidity during this same period must not exceed 80%.Surfaces to be coated should be sound, rigid, clean and dry.An effective vapor barrier is required under surfaces on grade.Cracks in the concrete slab can be transmitted to the surface.During application and curing of CHEMOROC HD in locations where food products are processed or stored,adequate ventilation must be provided to prevent contamination of the food (taste, odor, etc.) by volatile constituents in the coating.Can be exposed to short intervals of temperatures up to 60°C. Temperatures for continuous service should not exceed 40°C.

WaterproofingFor complete waterproofing, a coat of elastomeric waterproofing membrane CHEMORFLEX 300 should be applied prior to CHEMOROC HD application (optional).

Surface preparationThe surfaces of the sub-floor must be sound, solid dust-free and have the proper slopes.

Chemoroc HDDescriptionCHEMOROC HD is a two component, epoxy based seamless coating for floors. Curing takes place at ambient temperatures even at 5°C.This is a 100% solids material containing epoxy resin, hardeners, flexibilizers, and mineral pigments.Aggregates to be added can be silica sand, aluminium oxide, carborundum, etc.CHEMOROC HD mortar is applied by trowel to a thickness of 3mm to 6mm, depending on the nature of the subsequent traffic, It provides a tough,seamless, impermeable surfacewith excellent resistance to traffic and common chemicals.The fluidity of CHEMOROC HD mortar can be easily adjusted by the amount of aggregate added de-pending on the use, eg., levelling, repair of damaged surfaces, making slopes.


ColorsStandard color is Grey C-4195.Special colors available on request.

FinishesChemorclad 250 ,«Orange Peel» or anti-skid. (see Data Sheet).

AdvantagesRapid installation even at low temperatures allows traffic within a few hours.Seamless, sanitary, impermeable, tough, durable.Thin, light weight.Can be applied to cove bases and plinths to seal the joints between floors and walls.Hard, resistant to heavy traffic.Dust free.Resistant to microbial growth(approved by Agriculture Canada).

Seamless floors / Chemoroc HD

115 Tri-Tex co inc.

CONSTRUCTIONc





Approx 11kg/m2.


Reagent Result


Unchanged


Unchanged

SafetyProducts are combustible in the liquid state.Keep away from sparks and open flames.Avoid contact with the eyes and skin.Skin contact could cause dermatitis.Wear safety glasses, protective gloves & clothing.Refer to Material Safety Data Sheet.

The surfaces must be free of cavities and holes and all grease, oil, wax or any other material that could impair adhesion must be removed.New concrete should be water cured.Curing membranes must not be used.Before installing CHEMOROC HD the concrete must be roughened mechanically or chemically.Moisture content of the sub-floor must not exceed 15%.



Characteristics




ASTM C-579 90 MPa.




Abrasion Resistance (Taber Abrader, CS-17 Wheel, 1000g load,1000 cycles)


Hardness (SHORE D)

ASTM D-2240 86



ASTM E-831 2.5X10-6/mm/mm/°C.

Seamless floors / Chemoroc HD

116 Tri-Tex co inc.

CONSTRUCTIONc

Damaged areas can be easily and quickly repaired.Available in a variety of colors.

LimitationsTemperatures during application and for a period of 48 hrs.following application must be -1O°C. minimum.Relative humidity during this same period must not exceed 80%.Surfaces to be coated should be sound, rigid, clean and dry.An effective vapor barrier is required under surfaces on grade.Cracks in the concrete slab can be transmitted to the surface.During application and curing of CHEMOROC LT in locations where food products are processed or stored, adequate ventilation must be provided to prevent contaminationof the food (taste, odor, etc.) by volatile constituents inthe coating.Can be exposed to short intervals of temperatures up to 80°C. Temperatures for continuous service should not exceed 40°C.

Surface preparationThe surfaces of the sub-floor must be sound, solid dust-free and have the proper slopes.The surfaces must be free of cavities and holes and all grease, oil, wax or any other material that could impair adhesion must be removed.New concrete should be water cured. Curing membranes must not be used.Before installing CHEMOROC LT the concrete must be roughened mechanically or chemically.Moisture content of the sub-floor must not exceed 15%.

ApplicationSee, CHEMOROC Installation Bulletin.


Chemoroc LTDescriptionCHEMOROC LT is a two component, epoxy based seamless coating for floors. Curing takes place even at low temperatures. This is a 100% solids material containing epoxy resin, hardeners, flexibilizers, and mineral pigments. Aggregates to be added can be silica sand, aluminium oxide, carborundum, etc.CHEMOROC LT mortar is applied by trowel to a thickness of 3mm to 6mm, depending on the nature of the subsequent traffic, It provides a tough, seamless, impermeable surface with excellent resistance to traffic and common chemicals.The fluidity of CHEMOROC LT mortar can be easily adjusted by the amount of aggregate added depending on the use, eg., levelling, repair of damaged surfaces, making slopes.


ColorsStandard color is grey C-4195.Special colors available on demand.


AdvantagesCan be installed at low temperatures down to -10°C. andput in service in one or two days.Seamless, sanitary, impermeable, tough, durable.Thin, light weight.Can be applied to cove bases and plinths to seal the joints between floors and walls.Hard, resistant to heavy traffic.Dust free.Resistant to microbial growth (approved by Agriculture Canada).Solid adhesion to concrete, plywood and steel.Resistant to alkalis, dilute acids and a variety of aggressivechemicals.

Seamless floors / Chemoroc LT

117 Tri-Tex co inc.

CONSTRUCTIONc


Reagent Result


Unchanged


Unchanged

SafetyProducts are combustible in the liquid state.Keep away from sparks and open flames.Avoid contact with the eyes and skin.Skin contact could cause dermatitis.Wear safety glasses, protective gloves & clothing.Refer to Material Safety Data Sheet.

Characteristics




ASTM C-579 90 MPa.




Abrasion Resistance (Taber Abrader, CS-17 Wheel, 1000g load, 1000 cycles)


Hardness (SHORE D)

ASTM D-2240 86



ASTM E-831 2.5X10-6/mm/mm/°C.





Approx 11kg/m2.

Seamless floors / Chemoroc LT

118 Tri-Tex co inc.

CONSTRUCTIONc

LimitationsSurfaces to be coated should be sound,clean and dry.Surface to be coated must be at least 15°C.An effective vapor barrier is required under slabs on grade.Cracks in the support can be transmitted to the surface.Temperatures during application and for a period of 18 hrs. following application must be 15°C. minimum. Relative humidity during this same period must not exceed 80%.Can be exposed to short intervals of temperatures up to 60°C.Temperatures for continuous service should not exceed 40°C.During application and curing of CHEMORQUARTZ in locations where food products are processed or stored, adequate ventilation must be provided to prevent contamination of the food (taste, odor, etc.) by volatile constituents in the coating.

WaterproofingFor complete waterproofing, it is recommended that a coat of elastomeric waterproofing membrane CHEMORFLEX 300 should be applied prior to CHEMORQUARTZ application(optional).

Surface preparationThe surfaces of the sub-floor must be sound,solid dust-free and have the proper slopes.The surfaces must be free of cavities and holes and allgrease, oil,wax or any other material that could impairadhesion must be removed.New concrete should be water cured. Curing membranes must not be used.Before installing CHEMORQUARTZ the concrete must be roughened mechanically or chemically.Moisture content of the sub-floor must not exceed 15%.

ApplicationSee CHEMORQUARTZ Installation Bulletin.

Chemorquartz HDBDescriptionCHEMORQUARTZ HDB is a two component epoxy seamless floor coating. The base coat is an epoxy mortar applied and compacted by trowel to an average thickness of 3-5mm.The surfacing consists of colored quartz granules broadcast into a clear epoxy binder to a thickness of 2-3mm, giving a total system thickness of 5-8mm.The transparent finish may be gloss or satin.

ColorsThe granules are available in ten different permanent colorsallowing creation of attractive multicolor patterns.

Advantages• Durable, decorative seamless floor coating.• Anti-skid finish.• Thin and light weight.• Seamless, sanitary and impermeable.• Can be applied to cove bases and plinths to seal the

joints• between floors and walls.• Hard, resistant to traffic.• Dust free.• Solid adhesion to concrete, plywood and steel.• Resistant to common chemicals.• Resistant to microbial growth (approved by Agriculture

Canada).• Rapid installation.• Easy maintenance.

Uses• Interior buildings.• Hospitals and health centers.• Educational institutes.• Research establishments.• Detention centers.• Recreation centers.• Light industries.

Seamless floors / Chemorquartz HDB

119 Tri-Tex co inc.

CONSTRUCTIONc


Reagent Result

5% Acetic acid,10% Citric acid,10% Hydrochloric acid, 5% Lactic acid,10% Phosphoric acid,10% Sulphuric acid,10% Potassium hydroxide,3% Sodium hypochlorite, 10% Sodium hydroxide,Methanol,Toluene, Xylene, Skydrol, Beef Tallow, Mustard, Urine.

Unchanged

MaintenanceSweep, damp mop, wash with water and a mild detergent.







Characteristics




ASTM C-579 67 MPa.




Abrasion Resistance

ASTM D-4060 (Taber Abrader, CS-17 Wheel, 1000g load, 1000 cycles)

0.1g.

Hardness (SHORE D)

ASTM D-2240 86



ASTM E-831 2.7X10-6/mm/mm/°C.

Color stability ASTM C-2244 E ≤ 4.0



Accepted for use in meat plants.

Seamless floors / Chemorquartz HDB

120 Tri-Tex co inc.

CONSTRUCTIONc

LimitationsSurfaces to be coated should be sound,clean and dry.Surface to be coated must be at least 15°C.An effective vapor barrier is required under slabs on grade.Cracks in the support can be transmitted to the surface.Temperatures during application and for a period of 18 hrs. following application must be 15°C. minimum. Relative humidity during this same period must not exceed 80%.Can be exposed to short intervals of temperatures up to 60°C.Temperatures for continuous service should not exceed 40°C.During application and curing of CHEMORQUARTZ in locations where food products are processed or stored, adequate ventilation must be provided to prevent contamination of the food (taste, odor, etc.) by volatile constituents in the coating.

WaterproofingFor complete waterproofing, it is recommended that a coat of elastomeric waterproofing membrane CHEMORFLEX 300 should be applied prior to CHEMORQUARTZ application(optional).

Surface preparationThe surfaces of the sub-floor must be sound, solid dust-free and have the proper slopes.The surfaces must be free of cavities and holes and allgrease, oil, wax or any other material that could impairadhesion must be removed.New concrete should be water cured. Curing membranes must not be used.Before installing CHEMORQUARTZ the concrete must be roughened mechanically or chemically.Moisture content of the sub-floor must not exceed 15%.

ApplicationSee CHEMORQUARTZ Installation Bulletin.

Chemorquartz SLBDescriptionCHEMORQUARTZ SLB is epoxy seamless flooring prepared by broadcasting colored quartz granules onto a clear epoxybinder.Normal thickness is 2-3mm.The transparent finish may be gloss or satin.

ColorsThe granules are available in ten different permanent colorsallowing creation of attractive multicolor patterns.

Advantages• Durable, decorative seamless floor coating.• Anti-skid finish.• Thin and light weight.• Seamless, sanitary and impermeable.• Can be applied to cove bases and plinths to seal the

joints• between floors and walls.• Hard, resistant to traffic.• Dust free.• Solid adhesion to concrete, plywood and steel.• Resistant to common chemicals.• Resistant to microbial growth (approved by Agriculture


Uses• Interior buildings.• Hospitals and health centers.• Educational institutes.• Research establishments.• Detention centers.• Recreation centers.• Light industries.

Seamless floors / Chemorquartz SLB

121 Tri-Tex co inc.

CONSTRUCTIONc


Reagent Result

5% Acetic acid,10% Citric acid,10% Hydrochloric acid, 5% Lactic acid,10% Phosphoric acid,10% Sulphuric acid,10% Potassium hydroxide, 3% Sodium hypochlorite, 10% Sodium hydroxide,Methanol,Toluene, Xylene, Skydrol, Beef Tallow, Mustard, Urine.

Unchanged








Characteristics




ASTM C-579 67 MPa.




Abrasion Resistance


0.1g.

Hardness (SHORE D)

ASTM D-2240 86



ASTM E-831 2.7X10-6/mm/mm/°C.





Seamless floors / Chemorquartz SLB

122 Tri-Tex co inc.

CONSTRUCTIONc

UsesInterior buildings.Floors, stairs, plinths.Educational institutions.Hospitals and health centers.Kitchens.Pharmaceutical and cosmetic plants, electronics manufacturing, beverage bottling plants.Computer rooms.

LimitationsVery light or very dark colors not recommended.Surfaces to be coated should be sound, clean and dry.Surface to be coated must be at least 15°C.An effective vapor barrier is required under slabs on grade.Cracks in the support can be transmitted to the surface.Temperatures during application and for a period of 18 hrs. following application must be 15°C. minimum. Relative humidity during this same period must not exceed 80%.Can be exposed to short intervals of temperatures up to 60°C.Temperatures for continuous service should not exceed 40°C.During application and curing of CHEMORQUARTZ TR in locations where food products are processed or stored, adequate ventilation must be provided to prevent contamination of the food (taste, odor, etc.) by volatile constituents in the coating.

WaterproofingFor complete waterproofing, it is recommended that a coat of elastomeric waterproofing membrane CHEMORFLEX 300 should be applied prior to CHEMORQUARTZ TR application (optional).

Chemorquartz TRDescriptionCHEMORQUARTZ TR is a troweled two-component epoxy based seamless coating for floors.Curing takes place at ambient temperatures. This is a 100%solids material containing transparent epoxy resin, hardeners, flexibilizers and colored quartz granules.It provides a seamless impermeable surface with excellent resistance to light traffic and common chemicals.

Thickness 3mm minimum.

ColorsSee CHEMORQUARTZ color selector.Special colors available on demand.


Advantages• Attractive appearance of a variety of multicolored

patterns.• Thin and light weight.• Seamless,sanitary and impermeable.• Can be applied to cove bases and plinths to seal the

joints• between floors and walls.• Hard,resistant to traffic.• Dust free.• Solid adhesion to concrete, plywood and steel.• Resistant to common chemicals.• Resistant to microbial growth (approved by Agriculture


Seamless floors / Chemorquartz TR

123 Tri-Tex co inc.

CONSTRUCTIONc


Reagent Result

5% Acetic acid,10% Citric acid, 10% Hydrochloric acid, 5% Lactic acid, 10% Phosphoric acid, 10% Sulphuric acid,10% Potassium hydroxide, 3% Sodium hypochlorite, 10% Sodium hydroxide,Methanol,Toluene, Xylene, Skydrol, Beef Tallow, Mustard, Urine.

Unchanged









Surface preparationThe surfaces of the sub-floor must be sound,solid dust-free and have the proper slopes.The surfaces must be free of cavities and holes and all grease, oil, wax or any other material that could impair adhesion must be removed.New concrete should be water cured. Curing membranes must not be used.Before installing CHEMORQUARTZ TR the concrete must be roughened mechanically or chemically.Moisture content of the sub-floor must not exceed 15%.

Characteristics




ASTM C-579 62 MPa.




Abrasion Resistance


0.2g.

Hardness (SHORE D)

ASTM D-2240 86



ASTM E-831 2.7X10-6/mm/mm/°C.





Seamless floors / Chemorquartz TR

124 Tri-Tex co inc.

CONSTRUCTIONc

UsesConstructing base plates for machinery and towers for transporting electricity.Filling cracks.Grouting prestressed cables.Grouting pre-placed aggregates.

Directions for useThe quantity of water required when using CHEMORPLEX «A» is 5 to 10% less than that for a conventional grout, at equivalent fluidity.

To obtain maximum expansion of the grout after being placed, prepare only the quantity for each mix that can be used in less than one hour.

The following table serves as a guide to proportioning by weight.

Ingredient Deep of filling

Up to 6cm More than 6cm

Cement 2 parts 1 part 2 parts 1part

Fly ash 1 part none 1 part none

Sand none none 3 parts 1 part

Ratio : water/cement

0.36-0.40 0.36-0.40 0.44-0.49 0.44-0.49

CHEMORPLEX «A»

0.5% 0.5% 0.5% 0.5%

FormsIf required, they must be tight, properly adjusted and impervious.

Expansive grout should be restrained from flowing out in order to ensure maximum density, bond and strength.

PumpingPumps and hose fittings must be tight to prevent loss of water during work.

Chemorplex ADescriptionCHEMORPLEX «A» is an additive for Portland cement grouts designed to produce slow, controlled expansion while increasing fluidity.

The product is offered as a grey powder combining a balanced blend of fluidifying, expanding and water reducing agents.

Contains no chemical corroding substances (e.g. calcium chloride) that could attack steel.

AdvantagesCHEMORPLEX «A» can be used in all Portland cement grouts (type 10,20 or 30) with or without sand, fly ash or pozzolanic material.

CHEMORPLEX «A» is added as only 0.5% by weight on the cement (plus fly ash if there is any).

Grouts that use CHEMORPLEX «A» are exceptionally fluid, cohesive, workable and non-slumping.

Before initial set, grouts containing CHEMORPLEX «A» position themselves along all containing restraining surfaces due to gaseous expansion.

This expansion stops as the mortar hardens.

ApprovalCHEMORPLEX «A» is approved by Hydro-Quebec for use in expansive grouts for the construction of base plates of transmission towers. (Report available on request).

Miscellaneous / Chemorplex A

125 Tri-Tex co inc.

CONSTRUCTIONc

MixingFollow the recommendations of the “Prestressed Concrete Institute”:To the working mixer charge in the following sequence the calculated quantity of water, Portland cement, fly ash, CHEMORPLEX “A” and sand as required.

Mix until a homogeneous grout is obtained.

Never add extra water to the mix. If the fluidity is reduceddue to a delay in the operation, discard the old grout andprepare a new mix.

PresentationMoisture resistant bags of 16kgs.

Storage12 months if stored in a dry location.

SafetyAvoid contact with the eyes and skin.

Wash with clean water.

If this product causes irritation, consult a physician.


Miscellaneous / Chemorplex A

126 Tri-Tex co inc.

CONSTRUCTIONc

Directions for useAll weakly adhering material on the surface should be removed by sand blasting, wire brushing or sanding.

The surface should be free of oil, grease, dirt and all other contaminants.

The surface can be cleaned with trichloroethylene orChemor solvents SV-17 or SV-40.

Apply METPREP full strength or diluted with water up to 1 to 2 parts by volume.

Application can be with a sponge, brush or clean cloth.

To obtain the best results, establish the level of dilution byexperimenting.

Allow the product to remain on the surface for 5-10 minutes and then rinse with clean water.Let the surface air dry or wipe dry with a clean cloth.

Apply an appropriate anticorrosive primer, eg. CHEMORCLAD 9500.

SafetyUse with good ventilation.

METPREP contains phosphoric acid and is as a result corrosive.

Avoid all contact with the eyes and skin .

Wear rubber gloves and safety glasses.

In case of contact with eyes or skin wash immediately with running water.

If irritation persists, seek medical attention.


MetPrePDescriptionMETPREP is a phosphoric acid containing liquid metal conditioner.

This product removes oxides present on metal surfacesand replaces them by a thin inert protective layer which improves adhesion of subsequent coatings.

UsesIn preparation for painting of ferrous and non-ferrous metalsurfaces, eg., steel, aluminium, galvanized steel, copper, brass, etc.

PresentationSingle component liquid, containing phosphoric acid and organic solvents.

StorageOne year in original unopened container at 10-25°C.

Miscellaneous / MetPreP

127 Tri-Tex co inc.

CONSTRUCTIONc

Tri-Tex co inc.

TRIC

HR

OM

ATI

C W

EST,

CO

MM

ERC

E, C

ALI

FOR

NIA

, US

A

TRIC

HR

OM

ATI

C M

EX

ICO

, PU

EBLA

, ME

XIC

O

TRI-

TEX

US

A, C

HA

RLO

TTE

, NO

RTH

CA

RO

LIN

A, U

SA

TRI-

TEX

CO

IN

C.,

ST-

EUS

TAC

HE,

QU

EBEC

, CA

NA

DA

(HE

AD

OFF

ICE

& P

RO

DU

CTI

ON

)

TRIC

HR

OM

ATI

C E

GYP

T M

ISR

, CA

IRO

, EG

YPT

1001, Industriel blvd, St-Eustache, Quebec, Canada J7R 6C31-800-363-2660, 450-974-1001, Fax: 450-974-0162

www.tritex.com

Documents

-Tex Tri - mtcchem.netmtcchem.net/images/fichesENv4Web.pdf · In 2010, Tri-Tex co inc. has acquired Chemor Inc. to continue ... C-635 C-750 CRD-C 621 NCHRP RAPPORT 244 WALL AND CEILINGS