Upload
duongduong
View
231
Download
1
Embed Size (px)
Citation preview
STIM , TENS & TENS/EMS
INSTRUCTION BOOKLET
A Pract ica l Guide to
TENS Therapy
1) INTRODUCTIONExplanation of PainWhat is TENSHow Does TENS WorkWhat Can TENS be used forHow is TENS usedElectrode PositioningCautions & Contra-Indications
2) PROGRAMMES
3) PREPARING YOUR TENSNeckBackShoulderElbowArm, Hand and WristGroinQuadricepsKnee & AnkleSciatic PainGeneral Pain Treatment with BURSTHeadPhantom Pain
3) REFERENCES
2
INDEX
EXPLANATION OF PAINPain is a warning system and the body’s method of
telling us that something is wrong. Pain is
important; without it abnormal conditions may go
undetected , causing damage or injury to vital parts
of our bodies. Even though pain is a necessary
warning signal of trauma or malfunction in the
body, nature may have gone too far in its design.
Aside from its value in diagnosis, long-lasting
persistent pain serves no useful purpose. Pain does
not begin until a coded message travels to the
brain where it is decoded, analysed, and then
reacted to. The pain message travels from the
injured area along the small nerves leading to the
spinal cord. Here the message is switched to
different nerves that travel up the spinal cord to the
brain. The pain message is then interpreted,
referred back and the pain is felt.
WHAT IS TENS?Transcutaneous Electrical Nerve Stimulation is a
battery powered electrical unit which uses
electrodes placed onto the skin to deliver electrical
impulses to the nerve fibres which lie underneath
the skin surface. It is used to provide pain relief by
blocking pain signals to the brain via the spinal cord
and peripheral nervous system, and also stimulates
the production of endorphins, the body’s own pain
relieving mechanism. Usually the electrodes are
placed around the pain area or on acupressure
points.
Unlike medication, TENS does not produce side
effects such as nausea or drowsiness. It can be
administered while the client is going about
normal activity and is not addictive.
HOW DOES TENS WORK?The TENs Machine can work in two ways but firstly
it is important to understand how the body feels
pain. Messages are sent from the brain to all areas
of the body and back again by the nerves, which
run from the brain down the spinal cord spreading
out to the trunk, arms and legs. If you touch
something hot a message will flash along the
nerves, up the spinal cord and into the brain. A
second message would immediately be sent back
to the same area telling you to move your hand
away. This process takes only a fraction of a
second.
TENs works by a method called pain gating where
the stimulation of the TENs machine blocks the
messages to the brain telling it the body is
experiencing pain. It also encourages the brain to
produce the bodies own natural painkilling
hormones known as endorphins.
ARE THERE ANY DANGERS OR SIDE-EFFECTS WITH T.E.N.S.?Remember, the current travels through the skin
between pairs of electrodes and only penetrates to
a depth of 1-2 inches (to the level of the underlying
nerve fibres). Such a small electrical current does
not pose any danger. However, if you have a
cardiac condition, a pacemaker
or are pregnant, consult your
doctor before using your TENS.
For any conditions requiring
electrode placement around
the neck or head a health care
professional should be consulted.
01457 860444 01457 860555
3
TENS Therapy A Pract ica l Guide
INTRODUCTION
www.physiomedhomecare.co.uk [email protected]
WHAT CAN TENS BE USED FOR?TENS can be used to treat most types of pain where
the cause has been determined including:
Arthritis • Back Pain • Bruising Calf Strain • Dead Leg • Fibrositis Finger
Pain • Headaches Migraines Knee Pain • Lumbago MuscleStress • Neck Pain • Neuralgia Osteo-arthritis • Period Pains
Post Herpatic NeuralgiaPregnancy/Labour Pains Rheumatism • Sciatica
Shoulder Pain • SleeplessnessSpondylosis • Sports InjuriesTennis Elbow • Tenosynovitis
Wrist Pain
HOW IS IT USED?The Standard TENS treatment
(convention or high frequency
settings) is performed when the
Pulse Rate is set to 60 pulses
per second or more. The
sensation produced will be a steady buzzing or
tingling feeling between the electrodes. Because
the TENS signal is perceived as stronger than the
pain signal being produced by the body, it
effectively blocks the pain signal from travelling
along nerves to the brain. Most clients find that
high-frequency treatments produce the quickest
relief from pain, as well as providing several hours
of relief after the treatment.
Treatment duration - 30 - 60
minutes, or continuous if
required. Most modern units
are portable and can be
clipped to the belt while going
about normal activities.
Low-frequency or burst type of treatment is
produced when the Pulse Rate setting on the TENS
unit is set manually below 10 pulses per second (or
as with some units, at automatic burst mode. Low-
frequency treatments produce visible muscle
twitching often described as a tapping or pulsating
sensation. In reaction to this type of stimulation
the body releases endorphins (pain-killing
chemicals produced naturally in the body). These
endorphins act as a chemical nerve block to reduce
pain by interrupting the pain signals along the
nerves to the brain. Often this type of treatment
can take longer to be effective but the results last
longer.
nerves to the brain. Often this type of treatment
can take longer to be effective but the results last
longer.
POSITION OF THE ELECTRODESBest results are achieved by placing the electrodes
directly over the pain site. With dual machines,
additional electrodes can be positioned to surround
the site. Electrodes can also be used to stimulate
traditional acupressure points if required.
HOW DO I KNOW IT’S TIME TOREPLACE MY ELECTRODES?It is very important that the self-adhesive
electrodes (pads) be replaced when they no longer
stick well or if you begin to
feel a “stinging” sensation on
your skin. The usual life-span
is approximately 3-6 weeks,
depending on skin type and
weather conditions—
humidity will effect how long they last.
4
INTRODUCTION
Although most of these pre-
gelled reusable electrodes are
considered hypoallergenic, in
some cases people with
sensitive skin may develop an
allergy to a particular type of electrode, just like
some people who are allergic to certain band-aids
or tapes. One solution is to change the electrode
and there are also products available to help act as
a skin “barrier” in these situations.
CAUTIONS1. Read operation manual before use of TENS.
2. We emphasize that patient with an implanted
electronic device (for example, a pacemaker)
should not undergo TENS treatment without
first consulting a doctor. The same applies to
patients with any metallic implants.
3. If TENS therapy becomes ineffective or
unpleasant, stimulation should be
discontinued until its use is re-evaluated by
the physician or therapist.
4. Avoid adjusting controls while operating
machinery or vehicles.
5. Turn the T.E.N.S off before applying or
removing electrodes.
6. Series 3 T.E.N.S. devices have no AP/APG
protection. Do not use it in the presence of
explosive atmosphere and flammable
mixture.
WARNINGS1. Caution should be used in applying TENS to
patients suspected of having heart disease.
Further clinical data is needed to show there
are no adverse results.
2. Electrical stimulation safety has not been
established during pregnancy. Do not use
TENS during pregnancy.
3. Do not place electrodes on the front of the
throat as spasm of the Laryngeal and
Pharyngeal muscle may occur. Do not
stimulate over the carotid nerve, particularly
with patients with known sinus reflex
sensitivity.
4. Care should be taken so that when operating
potentially dangerous machinery the
stimulator controls are not changed abruptly.
5. Cases of skin irritation at the electrode site
have been reported. Stimulation should be
stopped and electrodes removed until the
cause of the irritation can be determined.
6. Electrodes should not be placed over the eyes,
in the mouth, or internally.
7. Keep this device out of the reach of children.
5
TENS Therapy A Pract ica l Guide
PLEASE NOTE!! Before using your TENS Machine, or for further information on its operation. Please read the manufacturers instructions carefully.
01457 860444 01457 860555 www.physiomedhomecare.co.uk [email protected]
CONVENTIONAL
Suitable for pain relief. The Therapy consists of
short electrical pulses where the stimulation may
never be so strong that any muscle contractions
occur. Electrodes are usually placed on the nerve
paths around the pain site.
TENS stimulation can be used for pain therapy for
the following:
Muscle pain • arthralgiatennis elbow • arthritis
osteoarthritis • goutfibromyalgie • tenosynovitis
capal tunne hip • and back pain muscle tension(myalgia)
sinusitis • neuritis etc.
MODULATION
Stimulation pulses vary for both pulse width and
stimulation current. The variation is random and
built up as: pulse width multiplied by stimulation
current being constant. This modulated TENS
prevents any habituation to a set pulse width and
has the following variables: frequency, pulse width
and treatment time.
Modulated TENS stimulation can be used for pain
therapy as mentioned for conventional mode.
However, for chronic conditions where long-term
treatment is required modulated TENS is
recommendable.
BURST
Stimulation form consisting of short series of pulses
with high frequency that are repeated with low
frequency. BURST stimulation is used for general
pain relief and stimulation must be so strong that
muscle contraction is perceived. In general terms
the electrode is placed on a large muscle near the
pain location. BURST has the following variables:
frequency, pulse width and treatment time.
The effect of the stimulation has to be strong to
achieve visible muscle movement; the muscle
tension will be affected an forced to movement. A
long-cycle pain relief is given with BURST
stimulation due to the fact that the body increases
its own production of the natural painkillers, the
endorphins.
BURST stimulation can be used for relief of
radiating pain such as...
Sciatic pain • back pain • sclerosestinnitus • circulatory disturbances
whiplash etc.
6
PROGRAMMES/SETTINGS
7
TENS Therapy A Pract ica l Guide
PREPARING YOUR TENS
1. Retract the sliding lid. Insert the battery and replace the lid.
2. Lift protective cover (1 and 2) and connectthe lead wires to the output channels on the device.
3. Connect the lead wires to the electrodes.
4. Clean the skin. Remove the plastic cover from the electrodes before attaching to the skin. The electrodes must not touch each other.
5. Switch on the TENS Machine by turning theon/off button clockwise.
6. Choose programme and adjust the stimulation level.
7. The stimulation automatically stops whentreatment time expires.
PREPARING YOUR TENS
01457 860444 01457 860555 www.physiomedhomecare.co.uk [email protected]
1 2 3
4 5
6 7
NECKMuscle tension in shoulder & neck cervical
syndrome
INDICATIONS:
• Rheumatism
• Whiplash
• Slipped disk
• Cervical strain
• Head ache
• Arthritis
8
ELECTRODES PLACEMENT - NECK
TENS Therapy A Pract ica l Guide
9
1) Back pain & muscle insufficiencyIf reinforcement of muscles is needed, use TENS on
both channels. In order to get the movements try
treatment for the stomach.
stomach (page 18)
2) Lower back pain & dysmenorrhoea The area above Os Sacrum is a junction of the
sensory nerve pathway for the lower back and the
abdomen.
BACK
INDICATIONS:
• Back pain
• Scolisosis
• BWS syndrome
• Bilateral radiation
• Dysmenorrhoea
• Labour pain
• Slipped disk
ELECTRODES PLACEMENT - BACK
01457 860444 01457 860555 www.physiomedhomecare.co.uk [email protected]
1 2
SHOULDER
INDICATIONS:
• Rheumatism
• Subluxation
• Shoulder dislocation
• Shoulder sprain
• Arthritis
• Frozen shoulder
If the shoulder feels cold, B is particularly
beneficially as BURST stimulation increases the
blood circulation.
1) Shoulder Pain2) Shoulder Subluxation
10
ELECTRODES PLACEMENT - SHOULDER
1
2
ELBOW
INDICATIONS:
• Rheumatism
• Tennis elbow
• Golf elbow
• Sports injuries
• Arthritic pain
• Pain radiation
11
TENS Therapy A Pract ica l Guide
ELECTRODES PLACEMENT - ELBOW
01457 860444 01457 860555 www.physiomedhomecare.co.uk [email protected]
12ARM, HAND & WRIST
INDICATIONS:
• Tendonitis
• Carpal tunnel
• Rheumatism
• Spasm and spasticity
1) Pain relief & Hand Paralysis (Apoplexy):
ELECTRODES PLACEMENT - ARM, HAND & WRIST
1
13
TENS Therapy A Pract ica l Guide
GROIN
INDICATIONS:
• Sports injury
• Overworked muscles and ligaments
• Dysmenorrhoea
ELECTRODES PLACEMENT - GROIN
01457 860444 01457 860555 www.physiomedhomecare.co.uk [email protected]
QUADRICEPS
INDICATIONS:
• Low back radiating pain
• Sensibility
1) Quadriceps insufficient
14
ELECTRODES PLACEMENT - QUADRICEPS
1
15
TENS Therapy A Pract ica l Guide
1) Knee painIf the pain is located on the inner side of the leg,
use the electrode placement shown on the left
knee
2) Pain at the joint of the ankleAt lateral pain, place the electrode as on the right
ankle; left ankle shows the electrode placements
to threat medial pain
ELECTRODES PLACEMENT - KNEE & ANKLE
01457 860444 01457 860555 www.physiomedhomecare.co.uk [email protected]
2
1
SCIATIC PAIN
INDICATIONS:
• Sciatic pain
• Post-Herpetic neuralgia of sciatic nerve
• Arthritic pain of sacrolliac joint
Channel A:Negative electrode (black) placed posterior on the
upper thigh and positive electrode (red) below
poplitae crease.
Channel B:Bilaterally at L5 - S1 level.
16
ELECTRODES PLACEMENT - SCIATIC PAIN
17GENERAL PAINTREATMENT WITH BURST
INDICATIONS:
• General pain
• Tinnitus
• Raynaud’s phenomenon
• Fibromyalgie
• Circulatory disturbances
• Gout
• Cold hand etc.
HEADINDICATIONS:
• Trigeminus
• Sinusitis
• Frontal headache
ELECTRODES PLACEMENT - GENERAL PAIN & HEADTENS Therapy A Pract ica l Guide
01457 860444 01457 860555 www.physiomedhomecare.co.uk [email protected]
18PHANTOM PAINElectrodes can be placed on painful trigger points,
correlated to peripheral nerves and spinal cord
segments that innervates the painful area. For
general pain management the BURST therapy as
shown at page 17 is recommended.
ELECTRODES PLACEMENT - PHANTOM PAIN
19
TENS Therapy A Pract ica l Guide
Walsh, D. (1997),TENS: Clinical Applications & Related Theory, Churchill
Livingstone
Ellis, B. (1996),A retrospective study of long term users of TNS, Br JTherapy & Rehabilitation 3(2);88-93
Han, J. et al (1991),Effect of low and high frequency TENS on Met-enkephalin-Arg-phe and dynorphin A immunoreactivityin human lumbar CSF Pain 47(3); 295-298
Garrison, D & Foreman, R. (1994),Decreased activity of spontaneous & noxiously evokeddorsal horn cells during TENS, pain 58(3);309-315
Walsh, D. & Baxter, D. (1996),Transcutaneous Electrical Nerve Stimulation - A reviewof experimental studies, Eur J Med Rehabil 6(2);42-50http://www.electrotherapy.org/electro/tens/tens.htm 31/01/2006
Transcutaneous Electrical Nerve Stimulation (TENS)Roche, P. & Wright, A (1990), An investigation into thevalue of TENS for arthritic pain. Physiotherapy Theory &Practice 6; 25-33
Alves-Guerreiro, J., G. Noble, et al. (2201).“The effect of three electrotherapeutic modalities uponperipheral nerve conduction and mechanical painthreshold.” Clinical Physiology 21(6):704-711.
Bodofsky, E. (2002).“Treating carpal tunnel syndrome with lasers and TENS.”Arch Phys Med Rehabil 83(12): 1806: author reply 1806-7.
Brosseau, L., s. Milne, et al. (2002). “Efficacy of thetranscutaneous electrical nerve stimulation for thetreatment of chronic low back pain. “spine 27(6): 596-603.
Carrol, E. N. and A. S. Badura (2001). “Focal intensebrief transcutaneous electric nerve stimulation fortreatment of radicular an postthoracotomy pain. “ ArchPhys Med Rehabil 82(2): 262-4.
Chandran, P. and K. A. Sluka (2003).“Development of opioid tolerance with repeatedtranscutaneous electrical nerve stimulationadministration.” Pain 102: 195-201.
Chesterton, L.S., P. Barlas, et al. (2002).“Sensory stimulation (TENS): effects of parametermanipulation on mechanical pain thresholds in healthyhuman subjects. “Pain 99: 253-262.
Chesterton, L.S., N.E. Foster, et al (2003).“Effects of TENS frequency, intensity and stimulation siteparameter manipulation on pressure pain thresholds inhealthy human subjects. “Pain 106(1-2): 73-80.
Cosmo, P., H. Svensson, et al. (2000).“Effects of transcutaneous nerve stimulation on themicrocirculation in chronic leg ulcers. “Scand J PlastReconstr Surg Hand Surg 34(1): 61-4.
Johnson, M. I. (2000).“THE clinical effectiveness of TENS in painmanagement.” Critical Reviews in Physical andRehabilitation Medicine 12(2): 131-149.
Lone, A. R., Z. A. Wafai, et al. (2003).“Analgesic efficacy oftranscutaneous electrical nervestimulation compared with Diclofenac Sodium inosteoarthritis of the knee.”
Physiotherapy 89(8): 478-485.http//www.electrotherapy.org/electro/tens/tens.htm31/01/2006
Palmer, S.T., D. J. Martin, et al. (2004).“Effects of electric stimulation on C and A delta fiber-mediated thermal perception thresholds.” Arch PhysMed Rehabil 85: 119-128.
Roche, P., H.-Y. Tan, et al. (2002).“Modification of induced ischaemic pain by placeboelectrotherapy.” Physiotherapy Theory and Practice 18:131-139.
Sherry, J.E., K. M. Oehrlein, et al. (2001).“Effect of burst-mode transcutaneous electrical nervestimulation on peripheral vascular resistance.” PhysicalTherapy 81(6): 1183-91.
Sluka, K.A. and D. Walsh (2003).“Transcutaneous electrical nerve stimulation: basicscience mechanisms and clinical effectiveness.” J Pain4(3): 109-21.
Walsh, D. M., G. Noble, et al. (2000).“Study of the effects of various transcutaneous electricalnerve stimulation (TENS) parameters upon the RIIInociceptive and H-reflexes in humans.” Clin Physiol20(3): 191-9.
Wang, R. Y., R.C. Chan, et al (2000).“Effects of thoraco-lumbar electric sensory stimulationon knee extensor spasticity of persons who survivedcerebrovascular accident (CVA). “J Rehabil Res Dev37(1): 73-9.
REFERENCES
01457 860444 01457 860555 www.physiomedhomecare.co.uk [email protected]
GRAPHIC SYMBOLS
1. Degree of Electrical Protection BF
2. Do not insert the plug into AC power supply socket
3. Direct Current (DC power source)
4. Timer
5. Low Battery
6. Increase Parameters
7. Decrease Parameters
8. Consult Instructions for use
9. Manufacturer
10. Serial Number
20
INSTRUCTIONS FOR ALL TENS MACHINES
MALFUNCTIONS
Should any malfunctions occur while using the EV-806 Digital TENS/EMS, check
- whether the parameters are set to the appropriate form of therapy.
Adjust the control correctly.
- whether the cable is correctly connected o the device. The cables should be
inserted completely onto the sockets.
- whether the LCD reveals the menu. If necessary, insert a new battery.
- for possible damage to the cable. Change the cable if any damage
is detected.
* If there is any other problem, please return the device to your distributor.
Do not try to repair a defective device.
01457 860444 01457 860555 www.physio-med.com [email protected]
21
TENS Therapy A Pract ica l Guide
INSTRUCTIONS FOR ALL TENS MACHINES
CONFORMITY TO SAFETY STANDARDS
The Physio-Med 3 Series Digital TENS/EMS devices are in compliance with
the EN 60601-1-2:2001 and EN 60601-1:1990+A1:1993+A2:1995+A13:1996
safety standards.
WARRANTY
All Physio Med TENS/EMS models carry a lifetime warranty from the date of
delivery. The warranty applies to the stimulator only and covers both parts
and labour relating thereto.
The warranty does not apply to damage resulting from failure to follow the
operating instructions, accidents, abuse, alteration or disassembly by
unauthorized personnel.
Manufacturer:
Everyway Medical Instruments Co., Ltd.
3FI., No.5, Lane 155, Sec. 3, Peishen Rd,
Shen Keng Hsiang,
222 Taipei Hsien, Taiwan, R.O.C.
Representative in the EU:
Physio-Med Services
Glossop Brook Business Park,
Surrey Street, Glossop,
Derbyshire, SK13 7AJ, England.
INFORMATION FOR DISTRIBUTOR:
Please contact the above mentioned manufacturer for technical support and
documentation when necessary.
The label attached to the back
of device contains important
information about this device-
model, supply voltage and
caution. Please do not remove.
22
PHYSIO-MED SERIES 3 TENS/EMS COMBO
TECHNICAL SPECIFICATIONSThe technical specification details of Physio Med Series 3 Stim are as follows:
MECHANISM TECHNICAL DESCRIPTION
Channel Dual, isolated between channels
Pulse Amplitude Adjustable, 0-100 mA peak into 500 ohm load each channel.
Wave Form Asymmetrical Bi-Phasic Square Pulse
Voltage 0 to 50V (Load: 500 ohm)
Power source One 9 Volt Battery.
Size 10.1cm(L) x 6.1cm(W) x 2.45cm(H)
Weight 150 grams with battery.
Pulse Rate Adjustable, from 2 to 150 Hz, 1 Hz/step
Pulse Width Adjustable, from 50 to 300µS microseconds,10µS/step
On Time Adjustable, 2~90 seconds , 1 Sec./ step
Off Time Adjustable, 0~90 seconds , 1 Sec./ step
Ramp Time Adjustable, 1~8 seconds, 1 Sec./ step, The “On” time will
increase and decrease in the setting value.
Mode Five TENS Modes: B(Burst), N(Normal),M(Modulation),
SD1( Strength Duration), SD2
Two EMS Modes: S(Synchronous), A(Alternate)
Burst Mode Burst rate: Adjustable, 0-5 – 5Hz
Pulse width adjustable, 50~300µS
Frequency fixed = 100 Hz
Normal Mode The pulse rate and pulse width are adjustable. It generates continuous stimulation
based on the setting value.
Modulation Mode Modulation mode is a combination of pulse rate and pulse width modulation. The
pulse rate and width are automatically varied in a cycle pattern. The pulse width is
decreased by 50% from its original setting in 0.5 second, then the pulse rate is
decreased by 50% from its original setting in 0.5 second. Total cycle time is 1 second.
In this mode, pulse rate(2-150Hz) and pulse width(50-300µs) are fully adjustable.
SD1 Mode The SD1(Strength-Duration) mode consists of automatic modulation intensity and
pulse width in 40% range. The intensity is always increasing while the pulse width is
decreasing and vice-versa. The intensity is decreased by 40% while the pulse width
is increased by 40% in 5 seconds. In the next 5 seconds, the intensity is increased
by 40% while the pulse width is decreased by 40%. Total cycle time is 10 seconds.
Pulse rate(from 2~150Hz) and pulse width (from 50~300µs) are fully adjustable.
11.
2.
9. 10.
7.
8.
1.
4.
3.
6.
1. Lead Connector
2. Intensity Control (on/off switch)
3. Panel Cover
4. Liquid Crystal Display
5. Mode Control
6. Set Control
7. Increment Control
8. Decrement Control
9. Battery Case
10. Belt Clip
11. Protective Cover
5.
01457 860444 01457 860555 www.physio-med.com [email protected]
23
TENS Therapy A Pract ica l Guide
PHYSIO-MED SERIES 3 TENS/EMS COMBO
OPERATING INSTRUCTIONSPhysio-Med Stim
Switch unit on using intensity controls (1)
Tens Mode
Press mode button (5) until Tens is displayed, press mode button to
choose B = Burst, N = Constant, M = Modulation SDI, SD2. After
selecting your choice press the Set Button (6) to select Pulse Width,
Pulse Rate, and Timer. Adjustment of all these parameters is made by
using the up/down buttons (7/8). Once all parameters are set
increase the intensity control (2) to the desired level.
EMS Mode
Press mode button (5) until EMS is displayed, press mode button to
select S=(Synchronous) or A = (Alternating). Now press set button (6)
to select your Pulse Width, Pulse Rate, Ramp Time, On Time, Off Time
and Treatment Time. All these parameters can be changed by using
the up/down buttons, (7/8). Once all parameters are set turn the
intensity control (2) to the required level.
PHYSIO-MED SERIES 3 TENS/EMS COMBO - Code: TPN 360
TECHNICAL SPECIFICATIONSThe technical specification details of Physio Med Series 3 Stim continued:
MECHANISM TECHNICAL DESCRIPTION
SD2 Mode The SD2(Strength-Duration) mode consists of automatic modulation intensity and
pulse width in 70% range. The intensity is always increasing while the pulse width is
decreasing and vice-versa. The intensity is decreased by 70% while the pulse width
is increased by 70% in 5 seconds. In the next 5 seconds, the intensity is increased
by 70% while the pulse width is decreased by 70%. Total cycle time is 10 seconds.
Pulse rate(from 2~150Hz) and pulse width (from 50~300µs) are fully adjustable.
Synchronous Mode Stimulation of both channels occurs synchronously. The “ON” time including “Ramp
Up” and “Ramp Down” time. Therefore, the setting of ON Time should be no less than
two times of the “Ramp” time in this mode. ON TIME ≥ Ramp up + Ramp down.
Alternate Mode The stimulation of the CH2 will occur after the 1st contraction of CH1 is completed. In
this mode, the setting of ON Time should be no less than two times of the “Ramp”
time. The OFF Time should be equal or more then ON Time. ON TIME ≥ Ramp up +
Ramp down. OFF TIME ≥ ON TIME.
Timer Adjustable, from 1 to 60 minutes or Continuous. Adjustable in 5 minutes each step.
Treatment time countdown automatically.
Patient Compliance Meter This unit can store 60 sets of operation records. Total recorded time is 999 hours.
Low Battery Indicator A low battery indicator will show up when the battery is low.
Operating Condition Temperature: 0˚~40˚C
Relative Humidity: 30%~75˚%
Atmosphere Pressure: 700Hpa~1060Hpa
Remark There may be up to a +/-5% tolerance of all parameters and a +/-10% tolerance of
amplitude and voltage.
11.
24
PHYSIO-MED SERIES 3 TENS
TECHNICAL SPECIFICATIONSThe technical specification details of Physio-Med 3 Series Tens are as follows:
MECHANISM TECHNICAL DESCRIPTION
Channel Dual, isolated between channels
Pulse Amplitude Adjustable, 0-100 mA peak into 500 ohm load each channel.
Wave Form Asymmetrical Bi-Phasic Square Pulse
Voltage 0 to 50V (Load: 500 ohm)
Size 10.1cm(L) x 6.1cm(W) x 2.45cm(H)
Weight 150 grams with battery.
Pulse Rate Adjustable, from 2 to 150 Hz, 1 Hz/step
Pulse Width Adjustable, from 50 to 300µS microseconds,10µS/step
Modes B(Burst), N(Normal), M(Modulation), SD1(Strength Duration), SD2
Burst Mode Burst rate: Adjustable, 0-5 – 5Hz
Pulse width adjustable, 50~300µS
Frequency fixed = 100 Hz
Normal Mode The pulse rate and pulse width are adjustable. It generates continuous stimulation
based on the setting value.
Modulation Mode Modulation mode is a combination of pulse rate and pulse width modulation. The
pulse rate and width are automatically varied in a cycle pattern. The pulse width is
decreased by 50% from its original setting in 0.5 second, then the pulse rate is
decreased by 50% from its original setting in 0.5 second. Total cycle time is 1 second.
In this mode, pulse rate(2-150Hz) and pulse width(50-300µs) are fully adjustable.
SD1 Mode The SD1(Strength-Duration) mode consists of automatic modulation intensity and
pulse width in 40% range. The intensity is always increasing while the pulse width
is decreasing and vice-versa. The intensity is decreased by 40% while the pulse
width is increased by 40% in 5 seconds. In the next 5 seconds, the intensity is
increased by 40% while the pulse width is decreased by 40%. Total cycle time is 10
seconds. Pulse rate(from 2~150Hz) and pulse width (from 50~300µs) are fully
adjustable.
1. Lead Connector
2. Intensity Control (on/off switch)
3. Panel Cover
4. Liquid Crystal Display
5. Mode Control
6. Set Control
7. Increment Control
8. Decrement Control
9. Battery Case
10. Belt Clip
11. Protective Cover
2.
9. 10.
7.
8.
1.
4.
3.
5.
6.
01457 860444 01457 860555 www.physio-med.com [email protected]
25OPERATING INSTRUCTIONSPhysio-Med 3 Series Tens
Switch unit on using intensity controls (1)
Press mode buttons (5) to select Burst, Normal (Constant) modulation
SD1, SD2, once selected press Set Button (6) to set parameters for Pulse
Width, Pulse Rate, and Treatment Time. To change these settings press
the Up/Down buttons (7/8). Once all parameters are set, turn Intensity
controls (2) to the required level
TECHNICAL SPECIFICATIONSThe technical specification details of Physio-Med 3 Series Tens continued:
MECHANISM TECHNICAL DESCRIPTION
SD2 Mode The SD2(Strength-Duration) mode consists of automatic modulation intensity
and pulse width in 70% range. The intensity is always increasing while the pulse
width is decreasing and vice-versa. The intensity is decreased by 70% while the
pulse width is increased by 70% in 5 seconds. In the next 5 seconds, the intensity is
increased by 70% while the pulse width is decreased by 70%. Total cycle time is 10
seconds. Pulse rate(from 2~150Hz) and pulse width (from 50~300µs) are fully
adjustable.
Timer Adjustable, from 1 to 60 minutes or Continuous. Adjustable in 5 minutes each step.
Treatment time countdown automatically.
Patient Compliance Meter This unit can store 60 sets of operation records. Total recorded time is 999 hours.
Low Battery Indicator A low battery indicator will show up on the LCD when the battery is low.
Operating Condition Temperature: 0˚~40˚C
Relative Humidity: 30%~75˚%
Atmosphere Pressure: 700Hpa~1060Hpa
Remark There may be up to a +/-5% tolerance of all parameters and a +/-10% tolerance of
amplitude and voltage.
PHYSIO-MED SERIES 3 TENSTENS Therapy A Pract ica l Guide
PHYSIO-MED SERIES 3 TENS - Code: TPN 350
26
11.
PHYSIO-MED SERIES 3 EMS
TECHNICAL SPECIFICATIONSThe technical specification details of Physio-Med 3 Series EMSs are as follows:
MECHANISM TECHNICAL DESCRIPTION
Channel Dual, isolated between channels
Pulse Amplitude Adjustable 0-100 mA into 500 ohm load each channel.
Output Voltage Adjustable 0-50V, Max output 50V peak to peak into 500ohm load each channel.
Wave Form Asymmetrical rectangular biphasic pulse.
Power Supply One 9 Volt Battery, type 6F22
Size 10.1cm(L) x 6.1cm(W) x 2.45cm(H)
Weight 150 grams (battery included)
On Time Adjustable, 2~90 seconds , 1 Sec./ step
Off Time Adjustable, 0~90 seconds , 1 Sec./ step
Ramp Time Adjustable, 1~8 seconds, 1 Sec./ step, The “On” time will increase and decrease in the
setting value.
Pulse Rate Adjustable, 2~150 Hz , 1Hz / step
Pulse Width Adjustable, 50~300µS , 10µS / step
Timer Adjustable, 1-60 minutes or Continue. Adjustable in 5 minutes each step. Treatment
time countdown automatically.
Output Mode Constant ,Synchronous, Alternate
Constant Constant stimulation based on setting value. Only pulse width, pulse rate and timer
are adjustable in this mode. “Constant” is equal to the “Normal” mode of a TENS unit.
Synchronous Stimulation of both channels occurs synchronously. The “ON” time including “Ramp
Up” and “Ramp Down” time. Therefore, the setting of ON Time should be no less than
two times of the “Ramp” time in this mode.
ON TIME ≥ Ramp up + Ramp down OFF TIME ≥ ON TIME
1. Lead Connector
2. Intensity Control (on/off switch)
3. Panel Cover
4. Liquid Crystal Display
5. Mode Control
6. Set Control
7. Increment Control
8. Decrement Control
9. Battery Case
10. Belt Clip
11. Protective Cover
2.
9. 10.
7.
8.
1.
4.
3.
5.
6.
01457 860444 01457 860555 www.physio-med.com [email protected]
27
TENS Therapy A Pract ica l Guide
PHYSIO-MED SERIES 3 EMS
OPERATING INSTRUCTIONSPhysio-Med 3 Series EMS
Switch unit on using Intensity Controls (1)
Press mode button (5) to select Constant, Synchronous, Alternate,
Press set button (6) to select Pulse Width, Pulse Rate, Ramp Time,
On Time, Off Time, and Treatment Time. Once adjusted by using the
Up/Down buttons (7/8) set the intensity level required using
intensity controls (2)
TECHNICAL SPECIFICATIONSThe technical specification details of Physio-Med 3 Series EMS continued:
MECHANISM TECHNICAL DESCRIPTION
Alternate The stimulation of the CH2 will occur after the 1st contraction of CH1 is completed. In
this mode, the setting of ON Time should be no less than two times of the
“Ramp” time. The OFF Time should be equal or more than the ON Time.
ON TIME ≥ Ramp up + Ramp down
OFF TIME ≥ ON TIME
Compliance Meter This unit can store 60 sets of operation records. Total recorded time is 999 hours.
Low Battery Indicator A low battery indicator will show up on the LCD when Indicator battery is low.
Operating Condition Temperature:0°~40°C
Relative Humidty:30%~75%
Atmosphere Pressure : 700Hpa~1060Hpa
Tolerance There may be a +/-10% tolerance of all settings and +/-
20% tolerance of output of intensity.
PHYSIO-MED SERIES 3 EMS - Code: EMS 350
Physio-Med Services Ltd.Glossop Brook Business Park, Glossop, Derbyshire, SK13 7AJ.
Tel: 01457 860 444Fax: 01457 860 555
Email: [email protected]: www.physiomedhomecare.co.uk
Physio-Med is part of the group. PM062/03-06