Roots Blower Booster Vacuum Pump Oil

Roots Blower Booster Pumps

Roots Blower Booster Pump:

These pumps work on the principle of positive displacement of gas. The

Roots pump consists of two impellers called roots in the shape of figure 8.

These impellers are mounted on parallel shafts in a single cylinder having

inlet and outlet openings on the sides. The impellers, through synchronized

rotative timing, are maintained in a relative position to each other and

rotated in opposite directions without any internal contact and at a very high

speed measuring a couple thousand or more rpm. The operating

clearances are very small, measuring just a few microns– only a few

thousandths of an inch - in order to keep back leakage to a minimum.

The following diagram shows how the rotation of impellers traps and pushes the gas/air out. The positive displacement works in a continuous flow to create vacuum.

Choose the Right Type of Lubricant

Often, out of ignorance, cost-cutting or any other reason, people use ordinary machine oil, automotive lubricants, gear oils or even normal rotary pump oil in these booster pumps. Since these oils do not have properties required for safe running of Booster Pumps, this leads to serious damage to the pump. Repairing a booster pump is nearly impossible without a complete overhaul which costs a lot while a new pump too costs lakhs of rupees. Choosing the right lubricant for the booster pump is the best type of insurance one can bank upon. A suitable, high quality booster pump oil is the pump’s primary protection against wear, pitting, spalling, scoring and scuffing of moving metal parts. The following pictures demonstrate the type of damage that can occur due to –

1. Wrong choice of lubricant

2. Not topping up at the right time, so the metal parts are not well-oiled.

1 2

3

4 5

6

Careful selection of lubricant goes a long way in saving the machinery thereby preventing loss of time and money.

When it comes to the choice of lubricant – One size DOES NOT fit all

Different vacuum processes require different types and grades of vacuum oil.

Supervac Roots Blower Vacuum Lubricants:

After careful actual testing on Roots blower pumps, Supervac has formulated Roots blower vacuum oil in two grades-

1. Hydro-carbon based booster pump oil- SV-90H

2. Silicone based booster pump oil- SV-90S

Both are suitable for all makes and sizes of Roots Booster pumps all over the world.

Specifications:

SV-90H (Hydrocarbon) SV-90S (Silicone)

Property

Value

Property

Value

Vapor Pressure at 250C Below 1x10-4 Torr Vapor Pressure at

250C

Below 1x10-4 Torr

Flash Point 2700 C Flash Point 3000 C

Viscosity at 400 C 90 cst Viscosity at 400 C 90 cst

Pour Point Below (-) 100 C Pour Point Below (-) 150 C

Appearance Pale Yellow Appearance Water White

Packaging (20 Ltrs.) (210 Ltrs.) Packaging (20 Ltrs.) (210 Ltrs.)

Equivalent

Edwards Stokes- V

lube Grade H oil

Lubricant

Equivalent

Roots Synthetic

Lubricant ISO VG 320

LVO 210

GS 555

HE 600

Supervac Roots Blower vacuum pump oils have the following properties –

1. Excellent lubrication

2. Heat dissipation

3. Protection of the pump machinery

It carries damaging wear debris away from contact zones.

Offer extreme temperature and pressure protection in order to prevent wear, pitting, spalling, scoring, scuffing and other types of damage that result in equipment failure and downtime.

Protection against-

1. Oxidation

2. Thermal degradation

3. Rust

4. Copper corrosion and

5. Foaming.

Pump parts come in contact with different types of contaminants like water, corrosive chemicals and surface wear debris which can cause serious and irreparable equipment failure.

What is so special about Supervac Roots Blower Vacuum Pump Oils?

Supervac Roots Blower lubricants have been formulated specially for Roots Booster vacuum pumps (also called positive displacement pumps) and are loaded with the following features –

Viscosity index improvers – Supervac brand Roots Blower pump oils have the viscosity - 90 cst at 400 C which is ideal for functioning of the pump. Special viscosity index improver additives make them work superbly in hot as well as cold climates.

Anti-foam additives –Impellers inside the pump are moved by gears at a very high speed (2000 or more rpm) and oil on them is churning at that point. Ordinary gear oil is likely to form foam. Formation of foam in Roots Blower pump is absolutely unwanted in a vacuum system. Just a trace amount escaping into the chamber can wreak havoc to the entire process. Supervac Roots Blower oils have been specially formulated keeping this important property in mind.

Wear protection additives – Along with lubrication, Supervac Roots Blower oils protect the machinery against wear like pitting, spalling and scuffing thereby enhancing the machinery life.

Corrosion inhibitors – Special additives in these oils resist corrosion caused by strong toxic process gasses.

Extremely high film strength

Low co-efficient of friction

Warning:

1) Supervac DOES NOT recommend the use of automotive lubricants or gear oils for Roots Blower pumps as they DO NOT have the above mentioned properties which are absolutely necessary for vacuum booster pumps.

2) Topping up of Booster Pump oil is absolutely essential to prevent pump damage. If level of oil falls below required level, immediately make up the level by adding more oil.

As is evident from the above diagram, a whopping 89% of the problems related with booster pumps are lubricant related. Merely choosing a good pump is not enough. If our money’s worth is to be taken out of that pump then it has to be run with the right oil and regular and timely topping up.

Often factory manufactured pumps come filled with booster pump oils. This oil must be changed within the break-in period initially and after set periods later on if we want the pump running smoothly and without any failures.