Plusart - Energy Meters - Sinalarte

Water Treatment SystemsSolar-powered Water Pumping

Systems of municipal water treatment are complex because of the responsibility to ensure that the population

distribution of water having the qualifications required by law.

We need the water treatment is adequate to the characteristics of the water collected and the needs and

expectations of the population. About its end use, there are systems of varying complexity.

The systems are based in a pretreatment unit (when required), a unit of sediment removal, correction units and

organoleptic characteristics of PH and finally disinfection. .

The Stations Water Treatment can work with advanced technological capabilities that increase efficiency and

reduce infrastructure maintenance and reagent consumption.

In countries that are concerned with economic policy and environmental water, we use different types of

treatment to make them suit the requirements of each.

In another sense, it is possible to perform research and development activities, away from established protocols

with the scientific and academic community.

CAPTURE

Water can come from a bayou,

a river, sea or deep and it is sent

to a tank raw water

Water treatment systems

2

Structure of the process of water treatment

PRETREATMENT (it is used for desalination)

PRE-OXIDATION

FLOCCULATION (it is not used for sea water)

Initial treatment is a pressurized filtration. The water collected by

filters down "beds", allowing a large reduction in turbidity. In several

conditions, one arrives at 95% reduction in turbidity.

We use this treatment if the water has organic matter and

microorganisms.

After the preoxidation is added to the water aluminum sulfate and

a flocculant. The addition of these reactive aggregates suspended

solids, allowing the separation in the later phases of treatment.It is necessary that the mixture of these products with water is

achieved without mechanical mixers, optimizing process efficiency

and reducing energy costs.

gama auraWater treatment systems

3 |

WATERMAKER (when required)

This process is complex. The saline solution is pressurized and a flow

of water through membranes, allows the passage of water and

prevents the passage of dissolved substances.

The flow of desalted water discharge is 20% to 50% in inlet flow.

ACTIVE CARBON

It removes pesticides and improves the organoleptic characteristics

of the water. It is used in exceptional situations.

FILTRATION

This process combines two processing steps:-The removal of particles that will be driven to the surface by air bubbles

introduced into the unit.-The clarified water goes directly into the filter, consists of beds

of sediment, where the solid particles smaller that were not

separated in the previous step are captured. This technology allows

effective removal of low-density substances including algae.

Process of treatment

FINAL DISINFECTION

ELEVATION OF THE TREATED WATER

SLUDGE TREATMENT

This process can be done with chlorine, hypochlorite or carbon

dioxide to ensure the bacteriological quality of water produced, or

leaving the treatment plant, or during distribution.

The treated water should be stored in a treated water reservoir.With water treatment, infrastructure must be equipped with a system

capable of treating the impurities resulting from water treatment and

control of quality.

Water cleaning filters and sludge collected at the surface of the

flocculator are conducted to the Sludge Treatment Unit, where they will be dehydrated.The water recovered during this process is sent to the raw waterreservoir, that is, to begin the process of water treatment.

4

QUALITY CONTROL

LABORATORYIn the laboratory tests are done to control the water quality

throughout the process.

INNOVATION

WATER TREATMENT IN REMOTE AREAS

During this process, there must be several points for the sample

and the automatic analysis of various parameters of water quality.

These allow constant monitoring of the effectiveness of the method

and quality control of produced water.

In a project root, separate water consumption of other waters. For

example, for irrigation water treatment is less demanding. Economic

studies show that this separation implies a cost reduction of nearly

60% of current expenditure.

With the advanced technology in areas as diverse as electronics

semiconductors and polymer chemistry, it is possible to idealize

complex systems of water treatment with an energy minimum. That is

why renewable energy has an important role in this type of project.

We can project autonomous systems of water treatment with minimal maintenance.

gama auraWater treatment systems

5 |

Solar-powered water pumping

6

12 x 195W (2340W)48V600AhActive Energy(under request)

Water Pump Stand-Alone Solar System*

PVBatteryAC PowerWater pump

230V (202V - 253V)50Hz, 60Hz4200W

Total solar power

AC PowerAC VoltageFrequency RangeAC Power (�25ºC)

2340W

Battery Bank 48V 600Ah

This process delivers water economically, cleanly and reliably even in remote places.

The stand-alone power system (SAPS or SPS), also known as remote area power supply (RAPS), is an off-the-grid electricity system for locations that are not fitted with an electricity distribution system.

It can be provide for all kinds of irrigation, such as agriculture, livestock, drop by drop, distribuition in entire villages (combinated with treatment systems).

We use high quality equipment and the sizing of the components (such as solar panels, water pumps, pipes diameters, batteries) is specially fitted for each project.

* Data related to a particular project and may vary depending on the characteristics of the project to develop.

Project example

Prepaid and postpaid energy meters

DESCRIPTION

Prepaid energy meters are measuring electronic link within. They are used to measure active energy

consumption. These products use a microcontroller that allows data acquisition, processing, storage, display

and control.

ADVANTAGES

Need a diagraph | High Performance | Firm structure

Small volume | Stability and credibility | Lightweight and easy to handle

The energy meters have three functions:

Electricity metering, control and micro-processing and the power circuit.

The energy metering using mass integration of integrated circuits, specialized to process the output signals of

energy. The microprocessor is, in turn, metering of electricity and at the same time, uses recordings to calculate

energy. It also transmits the card given to the electron energy (IC Card) that have to have access to all

information.

PARTICULARITIES: PREPAID ENERGY COUNTERS

This product enables the information management system energy sales encrypting the amount of electricity

purchased by the customer, saving it to the electronic card. The client has its own electronic card and uses the

energy he bought after paying for.

The management is made with a card that has a meter. Energy meters are equipped with a power management

system so the main function is to record the amount of energy used by the user on the energy map. Each counter

is associated with only one card that can be used on a counter.

Energy meters

8

TRANSPORTATION AND STORAGE

The counter should not be subjected to violent impact, and must be packaged according to GB / T 15464 一 1995,

"the general technique of packing counters and appliances."

The stock must be placed on shelves in the package, should not place over more than five layers.

It should be kept in place with ambient temperature from -40 º to +70 º.

WARRANTY

The warranty is 18 months from the day of sale, under the condition that comply with the specifications, using the

right mode of operation and keeping the seal intact.

Prepaid energy meters can be single or three phase.

Single phase meter - used to measure the active energy used

Three-phase meter - used to measure the active energy used on the three phases.

Single phase meter

Three phase meter

Normal operating voltage

0,9 ~ 1,1 (reference voltage)

0,9 ~ 1,1 (reference voltage)

Maximum operating voltage 0,8 ~ 1,15 (reference voltage) 0,8 ~ 1,15 (reference voltage)

Isolation voltage 2000 VAC 2000 VAC

Energy consumption 2 W e 10 VA 2 W e 10 VA

Normal temperature of operation (external) -40 º ~ 70 º -40 º ~ 70 º

Average level of annual moisture ~ 75% - 95% ~ 75% - 95%

Dimensions

197 mm x 108 mm x 60 mm

289 mm x 170 mm x 96 mm

Operation: When a reference voltage of 115% is applied, the circuit current decreases and produces only one

output signal energy.

Control use of energy: When the amount of power remaining is 0kWh the counter will turn off automatically until

that a new amount of electricity is introduced.

Electronic card and data protection: The electronic card (purchasing card) can be used multiple times and must

be kept properly.

After purchasing electricity for the first time, all customer information are written on the counter.

The data remains in an integrated circuit and without need to use battery. In case of lack of energy, the data will

not be lost.

gama aurasingle and three phase energy meter

9 |

Weight 850 g 850 g

10

Single Phase Prepaid Energy Meter

MODEL SPEM100DSPEM 100

Code of ReloadingDIN Rail Surface fixing

VERSION

230(5)8050-60

Active Energy165x114x70

DIN 7P750

-40 - 70

SPEM100D

SPEM100

SPEM100D-UIC

COMMUNICATION BOX

In the case of the meter with DIN rail attachment, the

external meter can be placed out of reach for users

and the communication unit is connected via

communication cable to the internal meter. Being

the meter accessible to the costumer, allowing the

reload and verification of information.

- Indication of the total consumption;

- Indication of partial consumption

(since the last reload);

- Alarm of low credit;

- Indication of price charged;

- Operational mode Smart Card or

Code of Reloading;

- Total control of costs;

- Better management of the budget;

- Avoid unexpected bills.

SPECIFICATIONS

PRODUCT ADVANTAGES:

Dimensions (mm) Surface FixingDIN Rail

Tension (V)Power (A)Frequency (Hz)Measure

Weight (g)Operating temperature (ºC)

gama auraSingle Phase Prepaid Energy Meter

11 |

MODEL SPEM101

SmartCardSurface fixing

VERSION

SPEM101

OPERATION

Smart Card Version

You can proceed to pre-paid reload of the meter at the registered

and authorized shops. After reloading the card, the user inserts

the card into the meter and the credit will be transferred.

Each card is non-transferable between meters or owners.

Reload Code Version


and authorized shops, ATM or by SMS or internet. With customer

data, the user receives a code which will be introduced into the

counter to perform the transfer of credit.

ACCESSORIES

- Energy electronic card: 1 unit

- (Optional) management system to sell electricity per card (including

reading, writing, machine management software system): 1 set

Three Phase Prepaid Energy Meter

12

3 x 2303 x (5)80

50-60Active Energy

230x145x70DIN 7P

1000-40 - 70

MODEL TPEM100DTPEM 100

Code of ReloadingDIN Rail Surface fixing

VERSION

TPEM100

TPEM100D

TPEM100D-UIC

COMMUNICATION BOX

In the case of the meter with DIN rail attachment, the

external meter can be placed out of reach for users

and the communication unit is connected via

communication cable to the internal meter. Being

the meter accessible to the costumer, allowing the

reload and verification of information.

- Indication of the total consumption;

- Indication of partial consumption

(since the last reload);

- Alarm of low credit;

- Indication of price charged;

- Operational mode Smart Card or

Code of Reloading;




SPECIFICATIONS

PRODUCT ADVANTAGES:

Dimensions (mm) Surface FixingDIN Rail



gama auraThree Phase Prepaid Energy Meter

13 |

MODEL DTSP200

Code of ReloadingPanel

VERSION

230(5)8050-60


2700-40 - 70

Dimensions (mm) Surface Fixing



- Indication of consumptions;

- Four quadrant analysis;

- Event log of such as loss of voltage, loss of current, reverse phase

sequence, overload, ;

- Sound and light alarm in the occurrence of events;

- Connector lid opening detection;




SPECIFICATIONS

PRODUCT ADVANTAGES:

DTSP200

MODEL TPEM101

SmartCardSurface fixing

VERSION

TPEM101

OPERATION

Smart Card Version


and authorized shops. After reloading the card, the user inserts

the card into the meter and the credit will be transferred.

Each card is non-transferable between meters or owners.

Reload Code Version


and authorized shops, ATM or by SMS or internet. With customer

data, the user receives a code which will be introduced into the

counter to perform the transfer of credit.

ACCESSORIES

- Energy electronic card: 1 unit

- (Optional) management system to sell electricity per card (including

reading, writing, machine management software system): 1 set

14

Three Phase Prepaid Energy Meter

The energy meters have three functions:

Electricity metering, control and micro-processing and the power circuit.

The energy metering using mass integration of integrated circuits,

specialized to process the output signals of energy. The microprocessor is, in

turn, metering of electricity and at the same time, uses recordings to

calculate energy. It also transmits the card given to the electron energy (IC

Card) that have to have access to all information.

SPECIFICATIONS

- Measurement of electrical energy with an option that allows multi-tariff of

consumption differentiated according to the date and time.

- Display of various registers on the LCD.

- The user can make payments through the traditional modes.

- Suitable for situations where the user needs free consumption (without

the need for recharging).

TPEM200D

TPEM200

SPEM200D

SPEM200

gama auraPostpaid Energy Meters

15 |

Postpaid Energy Meters

16

MODEL DTS200

Code of ReloadingPanel

VERSION

230(5)8050-60


2700-40 - 70

Dimensions (mm) Surface Fixing



- Indication of consumptions;

- Four quadrant analysis;

- Event log of such as loss of voltage, loss of current, reverse

phase sequence, overload, ;

- Sound and light alarm in the occurrence of events;

- Connector lid opening detection;

- Suitable for situations where the user needs free consumption

(without the need for recharging).

SPECIFICATIONS

PRODUCT ADVANTAGES:

DTS200

Panel DIN Panel DIN Panel DIN Panel DIN Panel

Legend

Includes: | Not available/Doesn’t apply: - | Op�onal:

SPEM100 SPEM100D SPEM120 SPEM120D TPEM100 TPEM100D TPEM120 TPEM120D DTSP200

Prepaid energy meters comparison table

17 |

Display informa�ons

Total Consump�on

Total Consump�on (by tariff)

Consump�on since the last charge

Remaining credit

Measurement

Ac�ve energy

Reac�ve energy

Class of Accuracy

Ac�ve energy

Reac�ve energy

Tariff

Simple tariff

Mul�ple tariff

Communica�on

Infrared (IEC 62056-21)

Serial port RS-485

PLC communica�on Module

Other features

CF Pulse LED

CF Pulse Output

Clock and Calendar

Backup ba�ery

Moun�ng

Accessories

User Interface console (cable)

User Interface console (RF)

Alterna�ve charging models

Smartcard Charging Model

Single Phase Three Phase

Postpaid energy meters comparison table

18

SPEM200 SPEM200D SPEM220 SPEM220D TPEM200 TPEM200D TPEM220 TPEM220D STS200

Display informa�ons

Total Consump�on

Total Consump�on (by tariff)

Consump�on since the last charge

Remaining credit

Measurement

Ac�ve energy

Reac�ve energy

Class of Accuracy

Ac�ve energy

Reac�ve energy

Tariff

Simple tariff

Mul�ple tariff

Communica�on

Infrared (IEC 62056-21)

Serial port RS-485

PLC communica�on Module

Other features

CF Pulse LED

CF Pulse Output

Clock and Calendar

Backup ba�ery

Moun�ng

Accessories

User Interface console (cable)

User Interface console (RF)

Alterna�ve charging models

Smartcard Charging Model

Single Phase Three Phase

Panel Panel Panel Panel Panel

Legend

Includes: | Not available/Doesn’t apply: - | Op�onal:

This system provides free power for charging mobile

phones, using sunlight and photovoltaic technology.

- It is a mobile equipment;

- It has the ability to recharge 100 cell phones /

day, with an autonomy of 3 days;

- In about 30 minutes, manages to recharge 65% of

the battery;

- Storage capacity for six cell phones

simultaneously;

- Standalone system and easy installation;

- Secure, for its safety boxes, as well of its easy

use;

- Result of a major aesthetic concern;

- Supports a variety of brands of mobile devices;

- Wins empathy within the consumers;

- LED lighting system at each station, with

presence detection.

* Given a cell phone with

battery 3,7V 1350mAh.

DESCRIPTION

ADVANTAGES

Solar charging station for mobile phones

19|

CHARACTERISTICSHeight (max.)Width (max.)N. of divisionsN. of chargesAnti-theft protectionInterface display

SOLAR CHARGING STATION2350mm1500mm

36 (5V@700mA)

Electronic codified system for closingLCD Display with numeric control

Nº Designation Qtd

1 Structural tube Ø120mmx2300 1

Support of the solar panel Ø1500

3 Base to attach the concrete

4 Acrylic divisions

5 Battery 1

6 Keypad

7 LCD Display

8 Shielding for batteries 2

9 Table

10 Charging box for cell phones 6

11 Automatic lock

12 Solar panel Ø1500mm

1

2 1

1

3

3

1

6

3

20

Solar charging station for mobile phones

cert if icaçãoa c r e d i t a d a

ENTM SE YG SA TN EA M

M

Manufacturing and commercializationof Road Signs, Traffic Lights,

Urban Furniture and LED Lighting Systems

2013/03 Edition

Find us on:

Business

Plusart - Energy Meters - Sinalarte