ISO-TECH

Iso-Tech is exclusively distributed by RS Components

Terms and conditions: Customers shall deal with RS Components Limited’s appointed distributor in the relevant territroy. The distributor will be soley responsible for the resale of products and services in this catalogue and the customer should therefore contact the distributor directly if there are any issues in relation to such products or services. All offers are available while stocks last. RS is trademark of RS Components Limited. An Electrocomponents Company.

Published by: RS Components Limited. Registered office: Birchington Road, Weldon, Corby, Northamptonshire NN17 9RS. Registered No. 1002091. RS Components Ltd 2009. RS are trademarks of RS Components Limited. An Electrocomponents Company.

InDUSTRIal TEST EQUIPMEnTPRODUCT GUIDE2012

EU_0

099

10/1

1

www.rs-components.com www.rs-components.com

Place FSC logo here

ISO-TECH PRODUCT GUIDE 2012 33www.rs-components.com

TEST lEaDS & aCCESSORIES

243-2998 Multimeter test leads CAT III 1000V, 10A

388-4126 Straight

388-4104 Right angled

388-4110 Fused crocodile clips

388-4132 500mA fuse x3

207-9913 High spec test lead set

425-3826 Fused test prods

388-4110 Fused crocodile clips

388-4132 Spare 500mA fuse x3

207-9907 Test leads

MUlTIMETER TEST lEaDS wITH CROCODIlE ClIPS•Suits ISO-TECH and most other digital multimeters•Push on probe tip insulators to prevent accidental short circuits•1.2m PVC leads

FUSED TEST lEaDS•Provides high degree of protection when measuring on high energy circuits •500mA/1000V 50kA fast acting HBC fuse in each probe•1.2m double insulated silicone leads with wear indicator•Available with straight or right angled connectors •Optional screw-in crocodile clips•EN61010 CAT III 1000V.

HIGH SPECIFICaTIOn TEST lEaDS wITH PUSH On CROCODIlE ClIPS•Push on probe tip insulators to prevent accidental short circuits•1.2m double insulated silicone leads•EN61010 CAT III 1000V. Current rating 15A

340-2538 Professional test leads

340-2544 Sprung grabbers

340-2588 Crocodile clips

340-2550 Fused test prods

340-2566 Crocodile clips fused

388-4132 Spare 500mA fuse x3

HIGH SPECIFICaTIOn TEST lEaD SET•Plug-in test probes with push on probe tip insulator•1.2m silicone insulated leads with straight connector

on one end and right-angled connector on the other•Optional plug-in accessories•EN61010 CAT III 1000V. Current rating 10A

HIGH SPECIFICaTIOn, MUlTIMETER TEST lEaD SETComplete multimeter test lead set:•Plug-in multimeter probes, spring-loaded grabber hooks & crocodile clips•1.2m silicone insulated leads with straight connector on one end

and right angled connector on the other •EN61010 CAT III 1000V. Current rating 15A

Optional accessories:•Fused test probes for increased protection on high energy circuits•Each probe is fitted with a 500mA 1000V HRC fuse. •Fused crocodile clips for use with the fused test probes

Welcome to the new Iso-Tech brochure

RS Components is a worldwide leading distributor of electronic, electrical and industrial components. ISO TECH is please to announce that RS will be an exclusive distributor for it’s test & measurement product range.

Visit the RS website to view the full product offer – including access to the complete Iso-Tech product range and details of all of the services available.

The ISO-TECH range caters for a wide variety of applications from the rugged and water resistant multimeters, through to digital light meters, sound level meters, to high performance digital oscilloscopes which feature functions generally found on the most expensive solutions.

ISO-TECH products are the brand of choice for engineers across the world who value their ruggedness, rely on their accuracy and know they will be there just when they need them.

ISO-TECH are so confident in the products they all come with a 3 year warranty as standard.

The ISO-TECH range offers an impressive selection of cost effective test and measurement equipment. all ISO-TECH products are manufactured and tested to international standards, so you can be assured you are putting your trust in a solution that won’t let you down.

ISO-TECH PRODUCT GUIDE 2012 1www.rs-components.com

COnTEnTS

mUlTImETERS

CURREnT ClamP mETERS

ElECTRICal InSTallaTIOn TESTERS

labORaTORy InSTRUmEnTaTIOn

bEnCH POwER SUPPlIES

CalIbRaTIOn & COmPOnEnT TESTInG

EnVIROnmEnTal mOnITORInG

Industrial hand held multimeters Rugged and water resistant meters with extensive functionality for industrial plant applications 2 - 3Electronic multimeters High specification multimeters for electronic, telecom and other demanding applications 4 - 5Compact tool box instruments Compact testers providing the essential electrical measurements for field service engineers NEW 6 - 7Bench multimeters Easy to use bench multimeters for electronic R&D and educational users 8

Current probes Safely extends the current measuring range of digital multimeters 9Industrial and HVAC clamp meters For safe non-intrusive measurement of high currents in process and industrial motor applications 10 - 13Electrical testers Clamp meter style testers for everyday tests on AC electrical systems 14 - 15

Power/power quality testers For power measurements and analysis in plant, automation and AC electrical systems 16 Insulation testers For testing electrical cable insulation in accordance with EN61557

NEW 17

Leakage current clamp Non-invasive testing of insulation resistance and fault leakage current 18

Analogue oscilloscopes Traditional analogue oscilloscopes for general electronics repair & test 19Digital storage oscilloscopes For digital design, test and education Spectrum Analyser For digital design using the frequency domain NEW 20 - 21Function generators Laboratory signal sources for electronic R&D, circuit testing and repair use 22 - 23

Programmable power supplies Programmable dc voltage sources with remote control for ATE systems and settings storage 24 - 25Multi output power supplies Ideal for powering circuits where closely tracking dual rail voltages are needed 26Single output power supplies Stable and accurate dc voltage sources for powering electronic circuits under controlled conditions 27 - 28

LCR meter Programmable laboratory meter for precision measurement of impedance 29Current/voltage calibrator Process tool for calibrating current loops, process devices and measuring process signals 29Component tester Maintenance engineer’s instrument to test semiconductors, resistors and capacitors 29

Light meters Light level meters for testing lighting conditions in the workplace 30EMF tester Monitor the electromagnetic field from power lines & appliances 30Sound level meters Sound meters for monitoring and assessing the safe working environment 31Photovoltaic Cell & Battery Testers Test tools for commissioning and maintaining solar cells & rechargeable batteries 32

ISO-TECH PRODUCT GUIDE 2012 3For more details and calibration options, go toISO-TECH PRODUCT GUIDE 20122 www.rs-components.com

InDUSTRIal HanD-HElD mUlTImETERSInDUSTRIal HanD-HElD mUlTImETERS

IDm100 SERIESHeavy duty, large format industrial multimeters with water resistant sealed cases, protected inputs and mains proof resistance ranges.

• Analogue Bargraph• Auto ranging with manual override• AC/DC voltage• 10A ac/dc current range• Display HOLD• Resistance / continuity & diode test• Frequency counter• Capacitance range• -20°C to 800°C temperature measurement

(IDM106N only)• Fuse protected current ranges• Automatic power off (battery save)

Size & Weight: IDM101: 98 x 200 x 52mm; 600gIDM103N, 105N,106N: 100 x 212 x 55mm; 620gAccessories included: Batteries, holster, test leads & instructionsIDM106N only: type K thermocouple adaptor and type K bead sensorPower: IDM101,103N &105N: 2 x AAA IDM106N: 9V PP3

Common Information

Specifi cations / Ranges / Model IDM101 IDM103N IDM105N IDM106N

Volts dc RangeBasic accuracyLowest range resolution

400.0mV - 600V ±(0.5% + 2d)

0.1mV

400.0mV - 1000V ±(0.25% + 2d)

0.1mV

400.0mV - 1000V ±(0.1% + 2d)

0.1mV

400.0mV - 1000V ±(0.1% + 2d)

0.1mV

Volts acRangeBasic accuracyLowest range resolution

4.000V - 600V ±(1.0% + 5d) 50 - 60Hz

1mV

400.0mV - 750V ±(1.5% + 5d) 40Hz - 1kHz

0.1mV

400.0mV - 750V ±(1.5% + 5d) 40Hz - 1kHz

0.1mV

400.0mV - 750V ±(1.5% + 5d) 40Hz - 1kHz

0.1mV

Current dcRangeBasic accuracyLowest range resolution

4.000mA - 10A±(0.8% + 2d)

1µA

40.00mA - 10A ±(0.7% + 2d)

10µA

40.00mA - 10A ±(0.5% + 2d)

10µA

40.00mA - 10A ±(0.5% + 2d)

10µA

Current acRangeBasic accuracyLowest range resolution

4.000mA - 10A ±(1.5% + 5d) 40Hz - 1kHz

1µA

40.00mA - 10A ±(1.5% + 5d) 40Hz - 1kHz

10µA

40.00mA - 10A ±(1.5% + 5d) 40Hz - 1kHz

10µA

40.00mA - 10A ±(1.5% + 5d) 40Hz - 1kHz

10µA

ResistanceRangeBasic accuracyLowest range resolution

400.0Ω - 40MΩ ±(0.7% + 2d)

0.1Ω

400.0Ω - 40MΩ ±(0.6% + 3d)

0.1Ω

400.0Ω - 40MΩ ±(0.4% + 2d)

0.1Ω

400.0Ω - 40MΩ ±(0.4% + 2d)

0.1Ω

Continuity <40Ω <30Ω <30Ω <30Ω

Diode Test 3V max 3V max 3V max 3V max

Frequencycounter

100Hz - 10MHz±(0.1% + 4d)

4000Hz - 40MHz±(0.01% + 1d)

4000Hz - 40MHz±(0.01% + 1d)

4000Hz - 40MHz±(0.01% + 1d)

CapacitanceRangeBasic accuracyLowest range resolution

4.000nF - 40µF±(1.0% + 4d)

1pF

4.000nF - 40mF±(2.0% + 8d)

1pF

4.000nF - 40mF±(2.0% + 8d)

1pF

4.000nF - 40mF±(2.0% + 8d)

1pF

697-4008 697-4001 697-4005 697-4014

Digital resolution (counts) 4000 4000 4000 4000Analogue bargraph • • • •Display backlight – • • •Auto / manual ranging • • • •RMS ac measurements – – – •Frequency counter • • • •Capacitance • • • •K type temperature – – – •Display HOLD • • • •Peak HOLD – – • •Relative measurement • – • •MIN/MAX • – • •Water resistant – • • •Safety category rating CAT III 600V CAT III 600V CAT III 600V CAT III 600V

IDm90 SERIESRugged industrial multimeters. Easy to use with features to suit most electrical and electronic applications.

• AC/DC voltage• 10A ac/dc current range• Resistance / continuity & diode test• Audible alarm warns when probes are

incorrectly inserted (IDM91E & IDM93N)• -20°C to 800°C temperature measurement

IDM99II only• Fuse protected current ranges• Automatic power off (battery save)

Size & Weight:

IDM91E & 93N: 95 x 192 x 50mm; 550gIDM97II & IDM 99II: 94 x 188 x 40mm; 460gAccessories included:

IDM91E, 93N & 97: battery, holster, test leads & instructionsIDM97II & 99II: battery, holster, test leads, crocodile clips & instructionsIDM99II only: Type K thermocouple adaptor and type K bead sensorPower:

IDM91E, 93N 7 99II: 9V PP3IDM97II 2 x AAA

Common Information

Specifi cations / Ranges / Model IDM91E IDM93N IDM97II IDM99II

Digital resolution (counts) 2000 2000 3400 4000Analogue bargraph – – • •Display backlight – – – •Auto / manual ranging Manual only Manual only • •RMS ac measurements – – – •Frequency counter – • • •Capacitance – • – •K type temperature – – – •Display HOLD – – • •Peak HOLD – – – •Relative measurement – – – •MIN/MAX – – – •Water resistant • • – –Safety category rating CAT III 300V CAT III 300V CAT III 600V CAT III 600V


200.0mV - 600V±(0.5% + 1d)

0.1mV

200.0mV - 600V±(0.5% + 1d)

0.1mV

300.0mV - 1000V±(0.25% + 1d)

0.1mV

400.0mV - 1000V±(0.25% + 1d)

0.1mV


200.0mV - 600V±(1.25% + 4d) 40 - 500Hz

0.1mV

200.0mV - 600V±(1.3% + 4d) 40 - 500Hz

0.1mV

3.000V - 750V±(1.3% + 5d) 40Hz - 1kHz

1mV

400.0mV - 750V±(1.3% + 5d) 40Hz - 1kHz

0.1mV


200.0µA - 10A±(1.0% + 1d)

0.1µA

200.0µA - 10A±(1.0% + 1d)

0.1µA

30.00mA - 10A±(1.5% + 2d)

10 µA

40.00mA - 10A±(0.7% + 2d)

10 µA


200.0µA - 10A±(1.5% + 3d) 40 - 500Hz

0.1µA

200.0µA - 10A±(1.5% + 3d) 40 - 500Hz

0.1µA

30.00mA - 10A±(2.0% + 5d) 40Hz - 1kHz

10 µA

40.00mA - 10A±(2.0% + 5d) 40Hz - 1kHz

10 µA


200.0Ω - 20MΩ±(0.75% + 1d)

0.1Ω

200.0Ω - 20MΩ±(0.8% + 1d)

0.1Ω

300.0Ω - 30MΩ±(0.7% + 3d)

0.1Ω

400.0Ω - 40MΩ±(0.4% + 3d)

0.1Ω


Diode Test 3.2V max 3.2V max 3V max 3V max

Frequencycounter

2000Hz - 200kHz±(1.0% + 3d)

3000Hz - 30MHz±(0.01% + 1d)

4000Hz - 40MHz±(0.01% + 1d)


2.000nF - 200µF±(2.0% + 4d)

1pF

4.000nF - 40mF±(2.0% + 8d)

1pF

697-4049 697-4058 697-4051 697-4055

• Available – Not available• Available – Not available


ElECTROnIC HanD HElD mUlTImETERSCOmPaCT HanD-HElD mUlTImETERS

IDm60 & 70 SERIESCompact multimeters that fit neatly in the palm of the hand for convenient single handed operation. The IDM70 series offer excellent performance with CAT IV 600V rating for tough industrial and electrical environments.

• AC/DC voltage• Resistance / continuity and diode test • Fully auto ranging with manual override• Integral non-contact ac voltage detector for

safe detection of hazardous mains voltage (IDM61 & 62T only)

• Display HOLD• Automatic power off (battery save)Size & Weight:

IDM61 & 62T: 156 x 74 x 44mm; 320gIDM71, 72 & 73: 82 x 164 x 44mm; 400gAccessories included:

IDM61, 62T, 71, 72 & 73: batteries, holster, test leads & instructionsIDM62T only: K thermocouple adaptor and type K bead sensorIDM73 software and RS232 cable kit available separately see stock no. 460-9881 Power:

IDM61, 62T & 71: 2 x AA batteriesIDM72 & 73: 9V PP3 battery

Common Information

Specifi cations / Ranges / Model IDM61 IDM62T IDM71 IDM72 IDM73

Digital resolution (counts) 2000 2000 6000 6000 6000Display backlight – – – – •AC/DC current – • – • •RMS ac measurements – – – • •Non-contact ac voltage detector • • – – –Frequency counter – • • • •Capacitance – • • • •K type temperature – • – – –MIN/MAX – • • • •RS232 interface – – – – •Safety category rating CAT III 600V CAT III 600V CAT IV 600V CAT IV 600V CAT IV 600V


200.0mV - 1000V±(0.5% + 2d)

0.1mV

200.0mV - 1000V±(0.5% + 2d)

0.1mV

600.0mV - 1000V±(0.5% + 2d)

0.1mV

600.0mV - 1000V±(0.5% + 2d)

0.1mV

600.0mV - 1000V±(0.5% + 2d)

0.1mV

Volts ac(50 - 300Hz)

RangeBasic accuracyLowest range resolution

2.000V - 750V±(1.5% + 5d)

1mV

2.000V - 750V±(1.5% + 5d)

1mV

600.0mV - 750V±(0.9% + 5d)

0.1mV

600.0mV - 750V±(0.9% + 5d)

0.1mV

600.0mV - 750V±(0.9% + 5d)

0.1mV


2.000A - 10A±(1.0% + 3d)

1mA

600.0µA, 6000µA±(1.0% + 2d)

0.1µA

600.0µA - 10A± (1.0% + 2d)

0.1µA

600.0µA - 10A± (1.0% + 2d)

0.1µA

Current ac(50 - 500Hz)


2.000A - 10A±(1.5% + 5d)

1mA

6.000A, 10A±(1.5% + 5d)

1mA

6.000A, 10A±(1.5% + 5d)

1mA


200.0Ω - 20MΩ±(1.0% + 3d)

0.1Ω

200.0Ω - 20MΩ±(1.0% + 3d)

0.1Ω

600.0Ω - 60MΩ±(0.7% + 2d)

0.1Ω

600.0 Ω - 60MΩ±(0.7% + 2d)

0.1Ω

600.0Ω - 60MΩ±(0.7% + 2d)

0.1Ω

Continuity <150Ω <150Ω <100Ω <100Ω <100Ω

Diode Test 2V max 2V max 3V max 3V max 3V max

Frequencycounter

RangeBasic accuracy

2000Hz - 20.00MHz±(0.01% + 1d)

6000Hz - 60.00MHz±(0.01% + 1d)

6000Hz - 60.00MHz±(0.01% + 1d)

6000Hz - 60.00MHz±(0.01% + 1d)


2.000nF - 2.000mF±(1.9% + 8d)

1pF

6.000nF - 6.000mF±(1.9% + 8d)

1pF

6.000nF - 6.000mF±(1.9% + 8d)

1pF

6.000nF - 6.000mF±(1.9% + 8d)

1pF

697-4023 697-4027 697-4033 697-4042 697-4045

• Available – Not available

IDm300 SERIES High specification multimeters with wide bandwidth and high accuracy measurements for electronic, telecom and other high demanding measurement and analysis applications.

The feature set includes large format triple display with an 80 segment bargraph with zoom and centre zoom, true RMS measurement and full autoranging on 12 functions. Data download software supports analysis and evaluation of results on a PC.

697-4011 IDM303

697-4020 IDM305

• Selectable 40000 / 4000 display resolution• 0.1% and 0.06% Vdc accuracy options• Large format triple display with

electroluminescent backlight• Easy to use on screen menu selection• 80 segment bargraph with zoom and centre

zero options• True RMS (a.c., a.c.+d.c.) measurement• Resistance/continuity and diode test• Isolated RS-232 output • 7 measurement memories

STORE & RECALL• Safety features include fuse failure

indication, high input voltage warning on display and high energy fused current inputs

Safety Rating:

EN61010-1 Cat III 600V CATII 1000V

Size & Weight:

100 x 212 x 55mm ; 650gPower: 9V PP3 batterySupplied with: protective holster, soft carry case, test leads set, crocodile clips, K type thermocouple adaptor and bead sensor, instruction manual and 9V alkaline batteryIDM305: RS-232 cable & WinDMM300 software.To use the IDM303 RS232 connection port the following accessories are available. RS-232 opto-isolated cable RS stock no. 456-7456.WinDMM300 software XP/NT compatible software RS stock no. 456-7456

Common Information Model IDM303 IDM305

4000/40000 selectable display resolution • •Basic accuracy dcV 0.1% 0.06%

Large format triple display with backlight • •AC/DC voltage & current • •True RMS measurement (ac, ac+dc) • •acV bandwidth 50kHz 100kHz

Capacitance measurement • •Frequency, period & duty cycle • •Auto ranging with manual override • •Fast peak HOLD (0.5ms) • •MIN/MAX MAX-MIN record with time stamp • •High/ low limits with time stamp • •Relative measurement with % display • •Programmable high & low level alarms • •7 measurement memories STORE & RECALL • •dBm and dB readings with selectable reference • •K type temperature measurement • •Datalogging with WinDMM software & RS232 cable Optional Supplied


40.000mV - 1000V±(0.1% + 2d)1µV

40.000mV - 1000V±(0.06% + 2d)1µV



400.00mV - 750V±(0.09% + 5d) 40 - 100Hz10µV

400.00mV - 750V±(0.7% + 5d) 40 - 100Hz10µV

Current ac (50 - 60Hz)


40.000mA - 10A±(0.3% +4d)1µA

40.000mA - 10A±(0.2% +4d)1µA


40.000mA - 10A±(1.0% +8d) 40Hz - 400Hz1µA

40.000mA - 10A±(0.8% +8d) 40Hz - 400Hz1µA


400.00Ω - 40MΩ±(0.4% +2d)0.01Ω

400.00Ω - 40MΩ±(0.3% +2d)0.01Ω

Continuity <50Ω <50Ω

Diode test 3.3V max 3.3V max


4.0000nF - 10mF±(1.4% + 20d)1pF

4.0000nF - 10mF±(0.9% + 20d)1pF

K type temperature RangeBasic accuracy

-200 - +1200°C±(3°C+1d)

-200 - +1200°C±(3°C+1d)

Frequencycounter

RangeBasic accuracy

400.00Hz - 4MHz±(0.01% +1d)

400.00Hz - 4MHz±(0.01% +1d)



COmPaCT TOOl bOX InSTRUmEnT

Volts dc Volts ac Resistance

Range Accuracy Resolution

320.0mV - 600V±(0.7% + 2d)0.1mV

3.200V - 600V±(1.7% + 5d) 1mV

320.0Ω - 30MΩ±(1.0% + 2d)0.1Ω

Continuity <20Ω

Diode Test 3.3V max

IDm5 wallET mUlTImETERSlim-line wallet multimeter with rotary function selector for easy one-handed control. The integral non-contact AC voltage detector allows quick and safe detection of mains voltages. Supplied with deluxe leather wallet for protection.

• 4000 counts LCD display• 8 functions / 30 ranges• Continuity, diode test & display HOLD• Capacitance, frequency counter & duty cycle• CAT III 300V safety rating

IDm17 PEn STylE mUlTImETERPen-style multimeter for probing onto electronic and electrical circuit boards and panels.

The optional ICA15 adaptor transforms the IDM17 into a clamp style meter to safely measure ac current up to 300A ac.

The IEK10 packs the IDM17 multimeter and the ICA15 current adaptor in a handy electrician’s kit.

IDm19 POCKET mUlTImETERSlim-line digital multimeter, small enough to slip into the pocket but safe for measuring mains voltages. Integral test leads stow away neatly behind the hinged back panel.

• 3400 counts LCD display with bargraph• 5 functions / 16 ranges• Selectable manual / auto ranging• Continuity, diode test & display HOLD• CAT III 300V safety rating

Size & Weight (with wallet):135 x 90 x 18mm; 135g Accessories included: 2 x LR44 1.5V coin cells (fi tted), instructions and integral test leadsPower: 2 x LR44 1.5V coin cells

Size & Weight:IDM17: 145 x 42 x 24mm; 120g ICA15: 72 x 102 x 36mm; 150gAccessories included (IDM17): batteries, probes, black test lead, carry pouch and instructionsPower (IDM17): 2 x AAA batteries

Size & Weight: 125 x 60 x 22mm; 110gAccessories included: 2 x LR44 1.5V coin cells, instructions and integral test leads

Volts dc Volts ac 50/60Hz Resistance


340.0mV - 600V±(2.0% + 2d)0.1mV

3.400V - 600V±(4.0% + 5d) 1mV

340.0Ω - 34MΩ±(2.0% + 4d)0.1Ω

Continuity <35Ω

Diode Test 2V max

697-4070 IDM17

697-3935 ICA15

697-4064 IEK10 electrician kit

697-3929 IDM19

697-4061 IDM5

Volts dc Volts ac Current dc Current ac


400.0mV - 600V±(0.7% + 5d)0.1mV

400.0mV - 600V±(0.9% + 5d) 0.1mV

400.0µA - 4mA ±(0.9% + 5d)0.1µA

400.0µA - 4mA±(1.5% + 5d)0.1µA

Resistance Capacitance Frequency Duty Cycle


400.0Ω - 40.00MΩ±(0.9% + 2d)0.1Ω

40.00nF - 400.0µF±(2.9% + 5d) 0.01nF

40Hz – 40kHz ±(0.3% + 5d)0.01Hz

0.1 – 99.9%±(0.1% + 10d)0.1%

Continuity <50Ω

Diode test 1.8V max

COmPaCT TOOl bOX InSTRUmEnT

IDm610 mUlTImETERInnovative multimeter with an integral, open jaw current clamp sensor, which allows you to safely measure up to 100A ac/dc in crowded cable areas.

• 3400 counts LCD display with bargraph• 6 functions / 18 ranges• 10mm open clamp sensor with 100A ac/dc current range• Resistance / continuity & frequency measurement• Fully auto ranging with manual override & display HOLD• CAT III 300V safety rating

IDm63nCompact multimeter that fits neatly in the palm of the hand with convenient single handed operation.

• 0.5% dcV basic accuracy• Resistance / continuity and diode test • Fully auto ranging with manual override• Display HOLD• Auto–power off• Tilt stand, nail hook and test lead storage• CAT III 600V safety rating

Size & Weight: 128 x 92 x 27mm; 220gAccessories included: 2 x AAA batteries, test leads, holster and instructions

Size & Weight: 128 x 92 x 27mm; 220gAccessories included: 2 x AAA batteries, integral test leads, integral open jaw current sensor, holster and instructions

Volts dc Volts ac 50 - 400Hz Resistance


340.0mV - 600V±(1.5% + 4d)0.1mV

3.400V - 600V±(1.5% + 5d) 1mV

340.0Ω - 34MΩ±(1.0% + 3d)0.1Ω

Current ac/dc Frequency


0 - 100.0A±(2.0% + 5d)0.1A

0 - 300kHz±(0.1% + 1d)1Hz

Volts dc Volts ac 50 - 300Hz Resistance


300.0mV - 600V±(0.5% + 2d)0.1mV

3.000V - 600V±(1.5% + 5d) 1mV

300.0Ω - 30MΩ±(0.8% + 2d)0.1Ω

Current dc Continuity Diode Test


300.0, 3000µA dc±(1.0% + 2d)0.1µA

<20Ω 3.3V max

702-3892 IDM610

697-4036 IDM63N

Innovative multimeter with an integral, open jaw current clamp sensor, which

IVP-1 VOlT PEnNon contact AC voltage indicator for safely checking the presence of an AC voltage in cables, wall sockets, fuses junction boxes etc.

• No current flow is needed for correct operation. • Tip glows red and the audible sounder activates when a voltage is detected.• Locates breaks in cables• Detects blown fuses inside plugs or fuse holders• Identifies voltage-carrying cables in junction boxes• Identifies faulty in-line switches and faulty lamps in series connection• CAT IV 1000V safety rating

Size & Weight: 152 x 22 x18 mm, 40gAccessories included: 2x AAA batteries and instructions

712-7398 IVP-1 NEW

CautionWill NOT detect cables behind buried plaster, buried trunking etc. and will not detect output from safety isolation transformers with earthed secondary centre tap. The unit should be checked for correct operation using a known voltage before use

Voltage Range: 200V - 1000V ac

Sensitivity (illuminates at 4mm distance from wire) :

240V ac

Frequency: 45Hz - 60Hz

Operating Conditions: 0 °C - +40 °C <80% rH


CURREnT PRObESbEnCH mUlTImETERS

ICa31 aC CURREnT TRanSDUCERThe perfect companion for your ISO-TECH digital multimeter. The ICA31 can safely measure up to 400A ac when used with the ac mV range on a digital multimeter.

• Non-intrusive AC current measurement• Coiled output cable (1.5m extended) fitted with 4mm shrouded plugs• Ergonomically designed jaw and trigger• Complies with EN61010-2-032 CAT III 300V

ICa32n aC/DC CURREnT PRObEDesigned for use with digital multimeters, this adaptor uses Hall effect sensors for measuring ac or dc current up to 600A.

• Indicator warning if left switched on• Low battery warning indicator• Auto-power off after 15 minutes• Coiled output prevents tangled leads• Complies with EN61010-2-032 CAT III 300V

ICa39T aC/DC CURREnT PRObEFor safe high current measurements when used with a digital multimeter.

• 1000A ac/dc measurement• Hall effect sensor technology• Large jaw size suits cables or bus bars• DCA auto zero button• Coiled output leads with right angle shrouded 4mm plugs• Power on and low battery indicators• Complies with EN61010-2-0-32 CAT III 1000V

ICa3000 aC FlEXIblE CURREnT PRObEA flexible current probe with 300A ac and 3000A ac wide bandwidth measurement ranges ideal for use with multimeters, recorders and data loggers.

• Wide bandwidth, low phase shift• Terminated with right angle 4mm shrouded plugs• Suitable for use with multimeters, recorders and data loggers• Complies with EN61010-2-0-32 CAT III 600V

Size & Weight:74 x 148 x 36mm; 250gAccessories included:Soft carry case & instructions

Size & Weight: 203 x 60 x 27mm; 380gAccessories included: 9V PP3 battery, soft carry case and instructions



697-3939 ICA31

697-3948 ICA32N

697-3941 ICA39T

697-3698 ICA3000

Range 0.1 - 400A ac

Output mV ac/A ac 1mV/A

Accuracy50 - 60Hz

3 - 350A ac: ±(1.9% + 0.5A)400A ac :±(3.2% + 1A)

Max conductor size 29mm Ø

Safety rating CAT III 300V

Output impedance 75Ω max

Range 100A ac/dc 600A ac/dc

Output mV/A ac/dc 10mV/A 1mV/A

Accuracydc: ac; 45 - 65Hz

±(2% + 2A)100 - 400A ac/dc: ±(2% + 2A)

400 - 600A ac/dc: ±(2.5% + 2A)



Load impedance 100kΩ min.

Range 0 - 100A ac/dc 1000A ac/dc

Output mV/A ac/dc 10mV/A 1mV/A

Accuracydc: ac; 45 - 65Hz

±(2.9% + 2A)100 - 400A ac/dc: ±(1.9% + 7A)

400 - 1000A ac/dc: ±(2.9% + 5A)



Load impedance 100kΩ min.

Range 300A ac 3000A ac

Output select 300mV 1V 300mV 1V

Output signal mV ac/A ac 1mV/A 3.33mV/A 0.1mV/A 0.333mV/A

Basic accuracy 50 - 60Hz 1% of full scale

Bandwidth -3dB 10Hz - 10kHz

Phase error ≤±1°



IDm200 SERIESCost effective bench multimeters for laboratory and educational use, the IDM 200 series are reliable and accurate and with their dual mains voltage / battery operation invaluable for field operations.

• Auto ranging with manual override• Display backlight• AC/DC voltage and current ranges• Display HOLD• Resistance / continuity & diode test• Capacitance range• Temperature Measurement (IDM207 only)• Fuse Protected current ranges

Size & Weight: IDM201N, 203 & 205: 218 x 195 x 73mm; 1.3kgIDM207: 203 x 233 x 96mm; 1.7kgSupplied accessories: IDM201N, 203 & 205: test leads, crocodile clips, carry strap & users instructions & power cordIDM207: test leads, crocodile clips, carry strap, users instructions, K type thermocouple adaptor, bead sensor, RS-232 cable, WinDMM300 software & power cordPower: 90 - 264V ac 50/60Hz 10VA min or 6 x AA alkaline (not supplied)

Common Information

Specifi cations / Ranges / Model IDM201N IDM203 IDM205 IDM207

665-5158 212-871 212-887 697-4017

Digital resolution (counts) 2000 4000 4000 40000/4000Analogue bargraph – • • •RMS measurements – – RMS (ac) RMS (ac, ac + dc)Frequency counter • • • •Period & duty cycle – – – •Capacitance • • • •Fast peak hold (0.5ms) – – – •MIN/MAX • • • •MAX-MIN record with time stamp – – – •High / low limits with time stamp and alarms – – – •Relative measurements – – • •dBm and dB readings with selectable reference – – – •K type temperature measurement – – – •STORE/RECALL function – – • •RS232 interface – – – •Safety category rating CAT II 600V CAT III 600V CAT III 600V CAT III 600V


200.0mV - 600V±(0.5% + 2d)

0.1mV

400.0mV - 600V ±(0.5% + 2d)

0.1mV

400.0mV - 600V±(0.5% + 5d)

0.1mV

40.000mV - 1000V±(0.06% + 2d)

1µV


200.0mV - 600V±(1.5% + 5d) 50Hz - 500Hz

0.1mV

4.000V - 600V ±(1.5% + 5d) 40Hz - 1kHz

1mV

4.000V - 600V±(1.0% + 5d) 40Hz - 1kHz

1mV

400.00mV - 750V±(0.7% + 5d) 40Hz - 100Hz

10µV


200.0µA - 10A±(1.0% + 2d)

0.1µA

4.000mA - 10A ±(0.75% + 2d)

1µA

4.000mA - 10A±(0.4% + 2d)

1µA

40.000mA - 10A±(0.2% + 4d)

1µA


200.0µA - 10A±(1.5% + 5d) 50Hz - 500Hz

0.1µA

4.000mA - 10A ±(1.5% + 5d) 40Hz - 1kHz

1µA

4.000mA - 10A±(1.0% + 5d) 40Hz - 1kHz

1µA

40.000mA - 10A±(0.8% + 8d) 40Hz - 400Hz

1µA


200.0Ω - 20MΩ±(0.7% + 3d)

0.1Ω

400.0Ω - 40MΩ ±(0.75% + 2d)

0.1Ω

400.0Ω - 40MΩ±(0.4% + 2d)

0.1Ω

400.00Ω - 40MΩ±(0.3% + 2d)

0.01Ω


Diode Test 3.0V max 3.0V max 3.0V max 3.3V max

Frequencycounter

2000Hz - 20MHz±(0.01% + 2d)

100.00Hz - 1MHz±(0.1% + 4d)

100.00Hz - 1MHz±(0.1% + 4d)

400.00Hz - 4MHz±(0.01% + 1d)


2.000nF - 2mF±(1.9% + 8d)

1pF

4.000nF - 40µF±(1.0% + 4d)

1pF

4.000nF - 40µF±(1.0% + 4d)

1pF

4.0000nF - 10mF±(0.9% + 20d)

1pF

K Type TemperatureRange Basic Accuracy

-200 to 1200°C±(3°C + 1d)



aC/DC CURREnT ClamP mETERSaC/DC CURREnT ClamP mETERS

AC/DC current measuring clamp meters for safe non-contact current measurement.

Select from the range, including the ICM30R slim-line model for use in tight spaces.

All the models feature RMS measurements to give the real value of an ac current for both pure and distorted waveforms.

Size & WeightICM30R: 66 x 192 x 37mm; 205gICM36R: 60 x 203 x 29mm; 310gICM36RII: 63 x 188 x31mm; 360gAccessories included:Battery, test leads, carry pouch & instructionsPower: ICM30R; 2 x AAA batteriesICM36R, 36RII; 9V PP3 battery

Common Information

Specifi cations / Ranges / Model ICM30R ICM36R ICM36RII

Digital resolution (counts) 4000 2000 4000Display backlight – – –Maximum current 300A ac/dc 600A ac/dc 600A ac/dcMaximum conductor size Ø 22mm 34mm 35mmAC/DC voltage measurement • – •RMS (ac) measurement • • •Resistance, continuity • – •Diode test – – –Frequency counter – – –K type temperature measurement – – –Capacitance measurement – – –Display HOLD • • •Peak HOLD – – –MIN/MAX MAX – MAXSafety category rating CAT III 300V CAT III 300V CAT III 600V


400.0mV - 600V±(0.5% + 2d)

0.1mV

400.0mV - 600V±(0.7% + 2d)

0.1mV



400.0mV - 600V±(1.5% + 5d)

0.1mV

400.0mV - 600V±(1.5% + 5d)

0.1mV



40.00A - 300A±(3.0% + 3d)

0.01A

200.0A, 600A±(1.9% + 5d)

0.1A

400.0A, 600A±(1.9% + 5d)

0.1A



40.00A - 300A±(1.5% + 5d)

0.01A

200.0A, 600A±(1.9% + 5d)

0.1A

400.0A, 600A±(2.0% + 5d)

0.1A


400.0Ω - 40MΩ±(2.5% + 5d)

0.1Ω

400.0Ω - 40MΩ±(0.9% + 3d)

0.1Ω

Continuity <50Ω <50Ω

Diode Test


TemperatureRangeBasic accuracy

Frequencycounter

RangeBasic accuracy

697-3967 697-3982 697-3985


Large jaw AC/DC current measuring clamp meters for safe non-contact current measurement.

Select from the range, including ICM2000 model where high current measurement is required for power and industrial motor applications.

All the models feature RMS measurements to give the real value of an ac current for both pure and distorted waveforms.

Size & WeightICM136R: 78 x 235 x 51mm; 380gICM139R: 90 x 275 x 51mm; 420gICM2000: 112 x 271 x 46mm; 647gAccessories included:Battery, test leads, carry pouch & instructionsPower: 136R, 139R, 2000; 9V PP3 battery

Common Information

Specifi cations / Ranges / Model ICM136R ICM139R ICM2000

Digital resolution (counts) 4000 4000 4000Display backlight • • –Maximum current 600A ac/dc 1000A ac/dc 2100A ac / 2500A dcMaximum conductor size Ø 35mm 51mm 55mmAC/DC voltage measurement • • •RMS (ac) measurement • • •Resistance, continuity • • •Diode test – – •Frequency counter • • •K type temperature measurement – – –Capacitance measurement – – –Display HOLD • • •Peak HOLD • • –MIN/MAX • • •Safety category rating CAT III 600V CAT III 600V CAT III 600V


400.0V, 600V±(0.7% + 2d)

0.1V

400.0V, 1000V±(0.7% + 2d)

0.1V

400.0mV - 600V±(1.5% + 3d)

0.1mV



400.0V, 600V±(1.0% + 5d)

0.1V

400.0V, 750V±(1.0% + 5d)

0.1V

400.0mV - 600V±(2.0% + 5d)

0.1mV



60.0A - 600A±(1.9% + 5d)

0.1A

400.0A, 1000A±(1.9% + 7d)

0.1A

400.0A - 2100A±(2.5% + 5d)

0.1A



60.0A - 600A±(2.5% + 5d)

0.1A

400.0A, 1000A±(1.9% + 7d)

0.1A

400.0A - 2500A±(2.0% + 3d)

0.1A


400.0Ω±(1.0% + 3d)

0.1Ω

400.0Ω±(1.0% + 3d)

0.1Ω

400.0Ω - 40MΩ±(1.5% + 3d)

0.1Ω

Continuity <30Ω <30Ω <40Ω

Diode Test 3V max



Frequencycounter

RangeBasic accuracy

20 - 400Hz±(0.1% + 2d)

20 - 400Hz±(0.1% + 2d)

100Hz - 1000kHz±(0.5% + 2d)

697-3932 697-3951 697-3702


For more details and calibration options, go toISO-TECH PRODUCT GUIDE 201212 ISO-TECH PRODUCT GUIDE 2012 13www.rs-components.com

aC CURREnT ClamP mETERS aC CURREnT ClamP mETERS

Specifi cations / Ranges / Model ICM3090 ICM33II ICM33RII

Digital resolution (counts) 4000 2000 2000Display backlight – – –Maximum current 400A ac 600A ac 600A acMaximum conductor size Ø 27mm 34mm 34mmAC/DC voltage measurement • ac V only ac V onlyRMS (ac) measurement – – •Diode test – – –Frequency counter – – –K type temperature measurement – – –Capacitance measurement – – –Display HOLD • • •Peak HOLD – – –MIN/MAX – – –Safety category rating CAT III 300V CAT III 300V CAT III 300V


400.0V, 600V±(1.0% + 5d)

0.1V



400.0V, 600V±(1.5% + 10d)

0.1V

600V±(1.2% + 3d)

1V

600V±(1.2% + 3d)

1V



40.00A, 400A±(2.0% + 10d)

0.01A

200.0A, 600A±(1.5% + 5d)

0.1A

200.0A, 600A±(1.5% + 5d)

0.1A


400.0Ω±(1.0% + 5d)

0.1Ω

2000Ω±(1.5% + 2d)

1Ω

2000Ω±(1.5% + 2d)

1Ω


Diode Test


TemperatureRangeBasic accuracyLowest range resolution

Frequencycounter

RangeBasic accuracy

Clamp meters for safe non-contact current measurement. All models include voltage, resistance and continuity measurements for general checks and trouble shooting of electrical installations.

Size & Weight:

ICM3090: 64 x 192 x 3mm; 250gICM33II, 33RII: 75 x 200 x 4mm; 360gAccessories included:

ICM3090, 33II, 33RII, battery, test leads, carry pouch & instructionsPower:

ICM33II, 33RII, battery 9V PP3ICM3090: 2 x AA batteries

Common Information


Specifi cations / Ranges / Model ICM133R ICM134 ICM135R

Digital resolution (counts) 4000 4000 4000Display backlight • • •Maximum current 1000A ac 600A ac 600A acMaximum conductor size Ø 51mm 32mm 34mmAC/DC voltage measurement • • •RMS (ac) measurement • – •Diode test – • –Frequency counter • – •K type temperature measurement – • –Capacitance measurement – • –Display HOLD • • •Peak HOLD • – •MIN/MAX • – •Safety category rating CAT III 600V CAT III 600V CAT III 600V


400.0V, 1000V±(0.7% + 2d)

0.1V

4.000V, 1000V±(0.9% + 5d)

1mV

400.0V, 600V±(0.7% + 2d)

0.1V



400.0V, 750V±(1.0% + 5d)

0.1V

4.000V - 750V±(1.5% + 5d)

1mV

400.0V, 600V±(1.0% + 5d)

0.1V



60.0A - 1000A±(1.9% + 5d)

0.1A

600.0A±(1.9% + 5d)

0.1A

60.0A - 600A±(1.9% + 5d)

0.1A


400.0Ω±(1.0% + 3d)

0.1Ω

400.0Ω - 40MΩ±(1.0% + 2d)

0.1Ω

400.0Ω±(1.0% + 3d)

0.1Ω


Diode Test 3V max 3V max 3V max


4.000nF - 4mF±(2.0% + 8d)

1pF

TemperatureRangeBasic accuracyLowest range resolution

-40°C - to 400°C±(1% + 4°C)

Frequencycounter

RangeBasic accuracy

20 - 400Hz±(0.1% + 2d)

20 - 400Hz±(0.1% + 2d)

697-3945 697-3954 697-3957

Clamp meters for safe non-contact current measurement. All models include voltage, resistance and continuity measurements for general checks and trouble shooting of electrical installations.

The ICM134 is optimised for testing heating, ventilation and air conditioning systems with the following added functions:

• 4000µA dc range for flame sensor testing• 4mF capacitance range• Type K thermocouple temperature measurement

Size & Weight:

ICM133R: 90 x 275 x 51mm; 420gICM134: 212 x 84 x 40 mm; 390gICM135R: 76 x 220 x 50mm; 360gAccessories included:

135R & 133R: battery, test leads, carry pouch & instructionsICM134: battery, test leads, carry pouch, type K thermocouple adaptor type K bead sensor & instructionsPower:

ICM134, 133R & 135R: 9V PP3 battery

Common Information


697-3709 697-3976 697-3979


POwER ClamP mETERSElECTRICal TESTERS

Slim-line testers with current clamp ideal for electrical maintenance and fault finding. The open jaw models provide fast non- intrusive current measurement without disturbing surrounding conductors.

ICM A9 smart tester automatically senses the circuit under test and selects either acV, dcV, Ω or acA measurement mode ensuring correct and safe measurements are made.

The ICM A5 includes an integral non-contact AC voltage detector for safe detection of hazardous mains voltages.

Size / weight

ICM A5: 54 x 193 x 31mm; 280gICM A7D: 84 x 175 x 31mm; 280gICM A9: 66 x 198 x 46mm; 260gICM20: 56 x 180 x 32mm; 250gAccessories included:

ICM A5, A7D, A9: battery, test leads & instructionsICM20: battery, carry pouch & instructionsPower

ICM A5: 2 x AAA batteriesICM A7D, A9: 9V PP3 batteryICM20: 2 x AA batteries

Common Information

Digital resolution (counts) 2000 2000 9999 2000AC current 200A ac 200A ac 400A ac 400A acAC/DC voltage measurement • • • –Automatic measurement selection – – • –Conductor jaw size Ø 16mm 12mm 27mm 27mmOpen jaw current clamp • • – –Non contact mains voltage detector • – – –Resistance/continuity • • • –Diode Test • – – –Display HOLD • • • •Automatic power off • • • •Safety category rating CAT IV 600V CAT III 600V CAT III 600V CAT III 600V


200.0V - 1000V±(1.0% + 2d)

0.1V

600.0V±(1.0% + 2d)

0.1V

1.8V - 600.0V±(1.0% + 2d)

0.1V

Volts ac (50 - 500 Hz)


200.0V - 750V±(1.5% + 5d)

0.1V

600.0V±(1.5% + 3d)

0.1V

1.3V - 600.0V±(1.5% + 3d)

0.1V



200.0A ±(3.0% + 3d)

0.1A

200.0A ±(3.0% + 3d)

0.1A

0.6A - 400.0A±(1.8% + 3d)

0.1A

20.00A - 400A±(2.0% + 0.5A)

0.01A


200.0Ω - 20MΩ±(1.0% + 2d)

0.1Ω

2000Ω±(1.0% + 2d)

1Ω

99.9Ω - 2000 Ω±(2% + 2d)

0.1Ω


Diode test 3V max

Specifi cations / Ranges / Model ICM A5 ICM A7-4 ICM A9 ICM 20


AC and AC/DC clamp meters with measurements of power, power factor, current and voltage for applications in plant automation and motor systems.

The IPM3000N ac power meter is optimised for testing flame sensors, motor start capacitors and temperature in heating and air conditioning systems.

• True RMS measurement• Phase angle and power factor measurement• Display HOLD• Resistance & continuity

Size & Weight: IPM138: 76 x 228 x 39mm; 465gIPM3000N: 76 x 228 x 39mm; 465gIPM6600: 117 x 271 x 46mm; 647gIPM2009R: 78 X 235 X 51mm; 380gAccessories included: IPM3000N, 6600 & 2009R: battery, carrying case, test leads & Instructions.IPM138: battery, carry case, test leads, type K thermocouple adaptor, type K bead sensor & instructionsPower: PP3 9V battery

Common Information

Specifi cations / Ranges / Model IPM138 IPM3000N IPM2009R IPM6600

Volts ac/dc (50 - 60Hz)


60.00V - 1000V±(1.0% + 5d)

0.01V

999.9mV - 600V±(1.0% + 20d)

0.1mV

400.0mV - 600V±(1.5% + 3d)

0.1mV

200.0V - 600V±(1.5% + 5d)

0.1V

Current ac/dc(50 - 60Hz)


600.0A±(1.5% + 5d)

0.1A

99.99A, 999.9A ac±(2.0% + 20d)

10mA

400.0A - 2100A ac / 2500A dc±(2.0% + 5d)

0.1A

200.0A - 2000A±(2.5% + 5d)

0.1A

True/Apparent Power kW/kVA


4.00k - 600kW/kVA±(2.5% + 5d)0.001kW/kVA

60.00k - 600.0kW/kVA±(5% + 20d)0.01kW/kVA

40.00kW - 400kW @250V±(2.5% + 5d)

0.01kW

99.99k - 1200kW/kVA±(2.0% + 0.5kW/kVA)

0.01kW/kVA


600.0Ω - 20kΩ±(1.0% + 5d)

0.1Ω

999.9Ω - 99.99MΩ±(1.0% + 10d)

0.1Ω

40.00Ω - 400Ω±(1.0% + 2d)

0.1Ω


Diode Test 3.0V max 2.0V max


9.999µF - 7000µF±1.5% ± 5d

1nF


-50° to 1000°C±(1% + 3°C)

-50° to 900°C±(1% + 1°C)

-50° to 1000°C±(1% + 2°C)

Frequency counter

RangeBasic accuracy

399.9Hz - 4000Hz±(0.1% + 5d)

40Hz, 1kHz±(0.5% + 2d)

10 - 400Hz±(0.5% + 2d)

* combined errors of voltage and current accuracy

697-4067 697-3746 697-3733 697-3780

Digital resolution (counts) 6000 9999 4000 9999

Dual display kW + PF,V + A, A + Hz, V + Hz. – • – •Maximum current 600A ac/dc 1000A ac 2100A ac / 2500A dc 2000A ac/dc

µA ac/dc measurement – • – –

Maximum conductor size Ø 35mm 40mm 55mm 55mm

Resistance, continuity • • • –

Active power measurement (kW) • • • •Apparent power measurement (kVA) • • – •K type temperature measurement • • – –

Capacitance measurement – • – –

Peak HOLD • – – –

MIN/MAX • • • –

Inrush current measurement • • – –

Relative measurement – – • –

Analogue output – – • –

Safety category rating CAT III 600V CAT III 600V CAT III 600V CAT III 600V


697-3989 697-3991 697-3995 697-3960


InSUlaTIOn & EaRTH TESTERS

IIT2301 & IIT2302 InSUlaTIOn TESTERSInsulation testers combining triple voltage insulation tests with 200mA continuity / resistance tests in accordance with EN61557-2, BS7671 and EN61010-1.

• Lock-down test button for continuous operation• Live circuit warning• Test lead resistance nulling

IIT2302 features

• Bargraph indication of test voltage• Automatic capacitive circuit discharge• Automatic test lead resistance nulling

IET1700 EaRTH TESTERComplete 3-pole earth testing kit specifically designed to measure ground resistance, in accordance with EN61557 and BS7671/17th Edition wiring regulations.

• 4000 count LCD with bargraph• 2mA @ 820Hz test current does not trip installation’s circuit breakers• MIN/MAX & data HOLD• Earth voltage test.

IIT1500 InSUlaTIOn RESISTanCE TESTERInsulation resistance tester in accordance with EN61557-2. Multiple test voltages and advanced measurements are ideal for trouble-shooting, commissioning and maintenance applications

• 4000 counts LCD display with analogue bargraph• Test voltages: 50V, 100V, 250V, 500V & 1000V• Polarisation Index (PI) and Dielectric Absorption Ratio (DAR) measurements • 600V AC/DC Voltage measurement range• Store/ Recall memory & compare (Pass/Fail) function• Includes remote test probe for fast testing• CAT IV 600V safety rating

Size & Weight: 175 x 115 x 86mm; 640gPower: 230V 10% 50/60HzSupplied with: 6 x AA batteries, test leads, crocodile clips and instructions

Size & Weight: 140 x 200 x 95mm; 990gPower: 230V 10% 50/60HzSupplied with: 8 x AA batteries, 3 x spikes, test leads and instructions

Size & Weight (with batteries & holster): 95 x 207 x 52mm; 630gSupplied with: Test-lead set, crocodile clips, remote test probe, rubber holster, tester hanging kit, 4 x AA alkaline batteries and instruction manual

IIT2301 IIT2302

Display Analogue LCD with bargraph

DC test voltages 250V/500V/1000V 250V/500V/1000V

Measuring range 10/200/400MΩ 20/200/2000MΩ

Output current 1mA dc 1mA dc

Basic accuracy 5% of reading20/200MΩ ±(1.5% + 3d)2000MΩ ±(10% + 3d)

Resistance range 0 - 2Ω, 0 - 20Ω 0 - 20Ω, 0 - 200Ω, 0 - 2000Ω

Basic accuracy ±3% (FS) ±(1.5% + 5d)

Continuity test 200mA min 200mA min

Ground Resistance Ground Voltage

Range 39.99Ω - 3999MΩ 399.9V

Display resolution 0.01Ω 0.1V

Accuracy ±(2% + 3d) ±(1.0% + 4V)

Safety category CAT III 300V CAT III 300V

530-5681 IIT2301

530-5697 IIT2302

697-3711 IET1700

Insulation Resistance

DC test voltagesMeasuring RangeTest currentBasic Accuracy

50V/100V/250V/500V/1000V50MΩ/100MΩ/250MΩ/500MΩ/20GΩ1mA (short circuit)±(3% + 5d)

Resistance

RangeAccuracyTest Current

40.00Ω - 40.00kΩ±(0.9% + 2d)>200mA (short circuit)

Voltage Measurement

Range 600Vdc 600Vac (50-500Hz)

Accuracy ±(1% + 5d) ±(2% + 5d)

675-5740 IIT1500

POwER QUalITy TESTERS

Specifi cations / Ranges / Model IPM3600 IPM3005 IPM6200 IPM6300

AC power quality testers with comprehensive functionality to diagnose power consumption power quality and power disturbance problems in single and balanced 3 phase electrical installations and power circuits. The IPM3600 has comprehensive real-time monitoring, recording and analysis of true 3-phase systems with fourth current clamp for neutral line measurement. Data transfer via USB interface for data download, voltage & current waveform and harmonic analysis.

USB interface and software for remotecontrol, real time monitoring and dataupload for analysis on a PCMaximum conductor size:IPM3005, 6300: Ø 170mmIPM6200: 55mm; 64 x 24mm bus barIPM3600: Cables Ø 40mmSize / weightIPM3005 & 6300: 130 x 80 x 43mm; 430gIPM6200: 271 x 112 x 46mm; 647gIPM3600: Instrument: 235x117x54 mm 730gCurrent probe(x4) : 193x88x40 mm; 333gAccessories included:IPM3005, IPM6200 & IPM6300Test leads, crocodile clips batteries, USB lead,software on CD-ROM & InstructionsIPM3600Instruction manualSoftware CD rom / Optical USB interfaceDeluxe carrying caseBattery ( “AA” 1.5V � 8pcs )UK/Euro AC adaptor (220V12V) 4 x current clamp transducers 4 x crocodiles test leadsPower IPM3005, IPM6200 & IPM6300: 2 x AA alkaline batteries IPM3600: 8 x AA batteries or 12V dcexternal adaptor

Common Information

AC RMS current range 1000A 3000A 1500A 3000AGraphical waveform display via PC link – • •Graphical phase diagram display via PC link – • •Display backlight • – • •Active power measurement W, kW, HP kW • • •Apparent power VA, kVA kVA • • •Reactive power measurement VAR, kVAR kVAR • • •Power factor and phase angle • • • •Energy calculation WH, kWH kWh & kVAh • • •Voltage and current harmonic measurement via PC link • • •Graphical harmonic analysis via PC link – • •Analysis of %THD via PC link – • •Crest factor measurement - • • •Transient detection of swell, dip and outage - – • •Fast PEAK HOLD (39µs) - • • –MAX, MIN and display HOLD via PC link • • •Maximum demand of selectable time period - – • •Real time clock • – • •

Data logging memory 20000 readings 8000 readings5000 reading / 32000

transient events5000 reading / 32000

transient eventsSelectable current transformer ratios - • • •Safety category rating CAT III 600V CAT III 600V CAT III 600V CAT III 600V

Volts ac(50 - 60Hz)


999.9V± (0.3% + 10d) (>50V)

0.1V

4.0V - 600V±(0.5% + 5d)

0.1V

4.0V - 600V±(0.5% + 5d)

0.1V

4.0V - 600V±(0.5% + 5d)

0.1V

Current ac RMS(50 - 60Hz)


999.9A ±(0.5% + 15d) (>3A)

0.1A

300.0A - 3000A±1% of range

0.1A

4.0A - 1500A±(1.0% + 5d)

0.1A

300.0A - 3000A±1% of range

0.1A

True/Apparent Reactive Power


999.9kW/kVA/kVAR±(1.0% + 20d)

0.1kW/kVA/kVAR

999.9 - 9999kW/kVA/kVAR±1% of range0.1W/VA/VAR

999.9 - 9999kW/kVA/kVAR±(1% + 20d)0.1W/VA/VAR

999.9 - 9999kW/kVA/kVAR±1% of range0.1W/VA/VAR

Power FactorRangeBasic accuracy

0.000 - 1.000±3dgts

0.000 - 1.000±0.04

0.000 - 1.000±0.04

0.000 - 1.000±0.04

Harmonics A ac, V ac

RangeBasic accuracy

1 - 31st ± %3THD

1 – 20th, 21-50th±2%, 4% of reading

1 – 20th, 21-50th±2%, 4% of reading

1 – 20th, 21-50th±2%, 4% of reading

FrequencyRangeBasic accuracy

60Hz±(0.1% + 2d)

45 - 65Hz±0.2Hz

45 - 65Hz±0.3Hz

45 - 65Hz±0.2Hz

%THDRangeBasic accuracy

--

0.0 - 100%±(6% + 1%)

0.0 - 100%±(6% + 1%)

0.0 - 100%±(6% + 1%)

725-5737 NEW 697-3743 697-3755 697-3768



lEaKaGE TESTERS analOGUE OSCIllOSCOPES

ISR SERIESDual channel oscilloscopes, sturdy, easy to operate and highly reliable, all feature a 6˝ rectangular display with internal graticule. Options include cursor measurements and numerical readouts for fast and accurate waveform measurements plus 10 memory storage of front panel settings ideal for product end of line test and routine set up.

• 6” rectangular CRT with 8 x 10 internal graticule

• High-stability and low-drift waveform representation

• AC, DC, GND input coupling• 1kHz Probe calibration output• X-Y Operation• CH1 signal output, Z axis input (5MHz)• TV synchronisation• Input voltage CATII 300V 400Vpeak max

(dc + ac)Size & Weight:

ISR622, 635: 310 x 150 x 455mm; 8.3kgISR2102 & 2112: 150 x 310 x 455mm; 9kgAccessories included:

Power cables (UK and Continental Europe), instruction manual, probesPower: 100-240V ac ±10%, 50/60Hz

Common Information

Specifi cations / Ranges / Model ISR622 ISR635 ISR6051

Bandwidth 20MHz 35MHz 50MHz

No. of channels 2 2 2

Rise time 17.5ns 10ns 7ns

Cursor readout – – •Delayed (B) sweep – – –Max sweep per division 10ns 10ns 10ns

Frequency counter – – •Time base AUTO range – – –Panel set up memory – – •ALT trigger • • –Hold-off function • • –

Vertical modes CH1, CH2, ADD, DUAL (CHOP/ALT), CH2 INV

Vertical sensitivity 1mVdiv - 2mVdiv ±5%; 5mVdiv - 5Vdiv ±3% 5mV - 20V/div ±3%

Time bases MAIN A MAIN A, ALT, DELAY (B)

A horizontal sweep time 0.1µs - 0.5s/div ±3% 0.2µs - 0.5s/div ±3%

B horizontal sweep time

Sweep amplifi cation x10 x5, x10 & x20

Trigger sources CH1, CH2, ALT, LINE, EXT Vert-mode CH1, CH2, LINE, EXT

Trigger slope “+” or “-“ polarity

Trigger coupling AC, DC, HF-REJ, TV AC, HFR, LFR, TV-V, TV-H

Trigger modes AUTO, NORM AUTO, NORM TV

Cursor readout ΔV, ΔT, 1/ΔT

Probe calibration output Squared wave; 1kHz ±5; 2Vpp ±3

Input impedance Approx. 5KΩ

Input coupling AC, DC, GND

Input voltage 400Vpeak max (dc + ac)

Screen 6” rectangular CRT with 8 x 10 internal graticule

248-8985 326-4651 514-4896


Volts AC Current AC Resistance

Range 400V 40.00mA - 60.0A 400.0Ω

Display resolution 0.1V 10µA 0.1Ω

Accuracy 50/60Hz40Hz - 1kHz

±(1.5% + 2d) ±(1.0% + 3d) ±(1% + 2d)

±(2% + 4d) ±(2.0% + 5d)

IlCm03 CURREnT lEaKaGE ClamP mETERSpecifically designed for ac leakage and load current measurements, the ILCM03 pinpoints leakage currents in conductors caused by poor insulation or modern electronic filters without powering down the installation or disconnecting protective earth conductors.

• 4000 count display• Fast bargraph display for transient observation • Wide bandwidth AC measuring ranges to measure effect of

high frequencies and harmonics• 30mm diameter conductor jaw capacity• Resistance and continuity range with beeper below 38Ω• MIN/MAX, HOLD, ZERO/RELATIVE value function• CATIII 300V safety rating

IlCm06 CURREnT lEaKaGE ClamP mETERLarge jaw clamp for AC leakage & load current measurements, the ILCM06 pinpoints leakage currents in single or 3 phase systems caused by poor insulation or modern electronic filters without powering down the installation or disconnecting protective earth conductors.

• Auto backlit 6000 count display with bargraph• 40mm diameter conductor jaw capacity• 400Hz Frequency response and 100Hz low pass filter mode• Auto, data & peak HOLD• CATIII 300V safety rating

Size & Weight: 210 x 62 x 36mm; 200gPower: 230V 10% 50/60HzSupplied with: 2 x AAA batteries, test leads, carry case and instructions

Size & Weight: 78 x 203 x 42mm; 300g (with battery)Supplied with: 2 AAA batteries and instructions

697-3721 ILCM03

• • • CATIII 300V safety rating

Current AC

Range 6.000mA - 100A ac 50/60Hz

Maximum resolution 1µA

Accuracy±(1% + 3d); 0 - 50A±(5% + 6d); 50 - 60A±(8% + 6d); 60 - 100A

248-8985 ISR622 20MHz Analogue Oscilloscope

326-4651 ISR635 35MHz Analogue Oscilloscope

514-4896 ISR6051 50Mhz Analogue Oscilloscope

677-0758 ILCM06


DIGITal STORaGE OSCIllOSCOPES

IDS8000 SERIES 2 and 4 channel high performance digital storage oscilloscopes. All models have bright colour TFT LCD displays for easy signal identification, 1GS/s single shot sample rate for capturing fast signals and 25K maximum record length for waveform capture of multiple and complex waveforms. The 25GS/s equivalent time sampling mode maintains an effective high sample rate for fast timebase settings for repetitive signals.

USB connectivity and PC communication software supports printer and PC communications and enables unlimited waveform and panel setup storage to USB flash drives.

619-5895 IDS8062 2 Ch. 60MHz

619-5902 IDS8064 4 Ch. 60MHz

619-5918 IDS8102 2 Ch. 100MHz

619-5924 IDS8104 4 Ch. 100MHz

619-5930 IDS8202 2 Ch. 200MHz

619-5946 IDS8204 4 Ch. 200MHz

Auto frequency counter Reduction: 6 digits; Accuracy: ±2%; Signal Source: All available trigger sources except the Video trigger mode

Probe calibration output Squared wave; 1kHz; 2Vpp ±3

Input impedance (CH1 - 4; EXT) 1MΩ ±2% ~16pF

Input coupling AC, DC & Ground

Maximum input 300V (dc ac peak), CATII

Screen 5.6 inch TFT LCD 234 x 320 DotsDisplay Graticule: 8 x 10 divisions, 8 x 12 divisions (menu off)Adjustable display brightness

Real time clock Display yy/mm/dd hh/mm/ss; provides Date/Time for saved data

Printer compatibility(USB) HP Deskjet 970CXI, LaserJet 1010 , LaserJet 1015, LaserJet 1300, Epson Stylus C20UX, Epson Stylus C65, Epson AL-C8600

Connection port USB Host device, RS232 and Go-No-Go output

• FFT transformed from the 200/100/60MHz bandwidths

• 2 or 4 input channels• 1GS/s real time and 25GS/s equivalent

time sampling• “Go-No Go” mode output• Maximum 25K points record length• Large 5.6” TFT colour display• USB Host / device: USB printer and Flash

drive support• Colour printout

Electrical protection category: CAT II 300VSize: 254 x 142 x 310mm Weight: 4.3 kgPower:

100 - 240V ac; 48 - 63Hz (automatic selection)Accessories included: Mains lead (UK and Continental Europe), PC control software on CD-ROM, x10 passive probes, instruction manual

Common InformationModel IDS8062 IDS8064 IDS8102 IDS8104 IDS8202 IDS8204

Band width 60MHz 60MHz 100MHz 100MHz 200MHz 200MHz

No. of channels 2 4 2 4 2 4

Rise time ~5.8ns ~5.8ns ~3.5ns ~3.5ns ~1.75ns ~1.75ns

Vertical resolution 8 bits ± (3% x Readout 0.05 div x Volts/div)

Vertical sensitivity 2mV/div 5V/div (1-2-5 increments)

Polarity Normal & Invert

Waveform signal process +, -, FFT

Trigger sources CH1, CH2, Line, EXT (2CH Only) / (CH3, CH4)

Coupling AC, DC, Lf rej., HF rej., Noise rej.

EXT trigger (2 channel models only)

Range: ±15V; Max Input 300V (dc ac peak), CATII; Sensitivity: dc - 30MHz ~50mV; 30M - 60/100/200MHz : ~100mV

Horizontal sweep time 1ns/div - 10s/div (1-2-5 increments); Roll: 250ms/div - 10s/div; Accuracy: ±0.01%

Horizontal modes Main, Window, Window Zoom, Roll, X-Y, Scan

Real time sample rate 1GS/sec (1 channel CH1 or CH2); 500MS/s (2 channels CH1 & CH 2);250MS/s (CH3 or CH4)

Equivalent sampling frequency 25GS/s equivalent sample frequency on each channel

Acquisition mode Sample, Peak Detect, Average, Accumulate

Peak Detection 10ns

Cursors and measurements

Voltage measurement Vpp, Vamp, Vavg, Vrms, Vhi, Vlo, Vmax, Vmin, Rise Preshoot / Overshoot, Fall Preshoot / Overshoot

Time measurement Freq, Period, Rise Time, Fall Time, Positive Width, Negative Width, Duty Cycle

Delay measurement Eight different delay measurements

Cursors measurement Voltage difference between cursors (ΔV) Time difference between cursors (ΔT)

DIGITal STORaGE OSCIllOSCOPES & SPECTRUm analySERS

699-4822 IDS6022 NEW 20MHz

699-4825 IDS6042 NEW 40MHz

699-4829 IDS6062A NEW 60MHz

699-4838 IDS6102A NEW 100MHz

699-4831 IDS6152A NEW 150MHz

Model IDS6022 IDS6042 IDS6062A IDS6102A IDS6152A

Band width 20MHz 40MHz 60MHz 100MHz 150MHz

No. of channels 2 2 2 2 2

Rise time 14 ns 8.75 ns 5.8 ns 3.5 ns 2.3 ns

Sample Rate 250 MSa/s 250 MSa/s 1 GSa/s 1 GSa/s 1 GSa/s

Vertical Sensitivity 2mV - 5V div 2mV - 5V div 2mV - 10V div 2mV - 10V div 2mV - 10V divMaximum Record Length

4KP 4KP 2MP 2MP 2MP

• TFT LCD display type• 300 V maximum input voltage• 1 MΩ resistance

Size (Length x Width x Depth):

310 x 142 x 140mm

Weight:

2.5kgPower Source:

Line voltage range AC 100V ~ 240V, 48Hz ~ 63Hz , Auto selectionPower consumption:

45W maximumAccessories included:

User manual, power cord, switchable passive probe

Common Information IDS6000 SERIES IDS6000 Series offers dual sampling mode, high-speed wave handling capability, advanced triggering functions, light weight and keen pricing. The IDS6000 general purpose DSO is a replacement for the analog oscilloscope and is widely used in laboratories & educational facilities, product testing & Quality Assurance, service operation & post-sales support and product development & debugging.

Vertical

AccuracyInput CouplingPolarityMaximum input

±(3% x |Readout| + 0.1 div + 1mV)AC, DC & GroundNormal & Invert300V (DC+AC peak), CATII

Horizontal

Accuracy Modes Pre-trigger Post-trigger

±0.01%MAIN, WINDOW, WINDOW ZOOM, ROLL, X-Y10 div maximum1000 div

Cursors and Measurement

Specifications

Voltage measurement Vpp, Vamp, Vavg, Vrms, Vhi, Vlo, Vmax, Vmin, Rise Preshoot/ Overshoot , Fall Preshoot/Overshoot

Time measurement Freq , Period , Rise Time , Fall Time , Positive Width , Negative Width , Duty Cycle

Cursors measurement Voltage difference between cursors, Time difference between cursors

Auto counterResolution: 6 digits, Accuracy: ±2%, Signal source: all available trigger source except the Video trigger mode

ISa 830 3GHz SPECTRUm analySERThe ISO-TECH ISA 830 Spectrum Analyser is affordable, easy-to-use and portable. Large internal memory facilitates the mass storage of measured traces, setup information, limit lines and user-defined macros. A very low noise floor level offers exceptional sensitivity for picking up weak signals. The interface design includes a Split-Window mode which enables the ISO-TECH ISA 830 to act as two spectrum analysers in one.

Low noise floor (-117dBm @ 1GHz, 3k RBW)

Autoset function

AC/DC/battery multi-mode power operation

Direct VGA output

6.4in (16.3cm) TFT Color LCD, Resolution: 640x480

• Bandwidth 9KHz - 3GHz

Compact Size:

33x17x34cm (13x6.7x13.4in)

Light Weight:

6kg (13.2lb) without optionsAccessories included:

User manual & power cord

Common Information

708-1592 ISA 830 NEW Spectrum analyzer, 3GHz

708-1598 ISA 830 TG NEW Spectrum analyzer, 3GHz with Tracking Generator

Special Features


FUnCTIOn GEnERaTORS FUnCTIOn GEnERaTORS

GFG 2000 & GFG 2110 SERIESSynthesized Function Generators with Direct Digital Synthesis technology for applications requiring precise and stable frequency outputs.

• Sine, triangle, square waveforms• Keypad or spin wheel setting of frequency and duty cycle• High frequency accuracy and stability• Low distortion sine wave• 6 digit 150MHz frequency counter (GFG 2110 model only)• 10 memory storage of frequency and duty cycle setup• TTL/CMOS output

Model GFG 2004 GFG 2007 GFG 2020

Frequency (sine, square) 0.1Hz - 4MHz 0.1Hz - 7MHz 1Hz - 20MHz

Frequency (triangle) 0.1Hz - 1MHz 0.1Hz - 1MHz 1Hz - 20MHz

TTL/CMOS output ≥3V / 4 - 15Vpp ≥3V / 4 - 15Vpp ≥3Vpp / 4 - 14Vpp

150MHz frequency counter – – –STORE/RECALL setups • • •Log/Lin Sweep – – –AM/FM modulation – – –

Model GFG 2110 GFG 2120

Frequency (sine, square) 0.1Hz - 10MHz 1Hz - 20MHz

Frequency (triangle) 0.1Hz - 1MHz 1Hz - 20MHz

TTL/CMOS output ≥3V / 4 - 15Vpp ≥3Vpp / 4 - 14Vpp

150MHz frequency counter • •STORE/RECALL setups • •Log/Lin Sweep • •AM/FM modulation • •

Display 9 Digit LED

Stability / accuracy ±20ppm

Sine wave flatness < ±0.5dB @ 4MHz

Sine wave distortion -40dBc max @4MHz

Triangle wave linearity ≥95% @ 1MHz

Duty control 20 - 80%, 2Hz - 1MHz (square wave only)

Amplitude range 2mV - 10Vpp (into 50Ω load)

Impedance 50Ω ±10%

Attenuator -20dB ±1dB x2

Power 115/230V ±15% 50/60Hz

Size & Weight:

107 x 266 x 293mm; 3.2kgAccessories included:

Power cord (UK and Continental Europe), BNC to crocodile clip test lead and instructions

Common Information GFG 8200 SERIESStable, low distortion function generator, the essential electronic lab instrument for circuit testing, set-up and repair.

• Sine, triangle, square waveforms• TTL, CMOS, Ramp outputs• Built-in 6 digit counter• LIN/LOG sweep mode (8255)• Duty cycle control• TTL/CMOS output

Model GFG 8216 GFG 8219 GFG 8255

Frequency range 0.3Hz - 3MHz 0.3Hz - 3MHz 0.5Hz - 5MHz

TTL/CMOS output ≥3V / 4-15Vpp ≥3V / 4-15Vpp ≥3V / 4-15Vpp

Frequency counter • • •Log/Lin sweep – • •AM/FM modulation – • •

Display 6 Digit LED

Stability / accuracy ±5% + 1Hz

Sine wave flatness < 0.5dB @ 300kHz - 3MHz

Sine wave distortion ≤ 1% @100kHz

Triangle wave linearity ≥95%

Duty cycle range 20 - 80% at 1MHz (square wave only)

Output amplitude >10Vpp (into 50Ω)

Output impedance 50Ω ±10%

Attenuator -20dB ±1dB x2

DC offset -5V to +5V (into 50Ω load)

Power 115/230V ±15% 50/60Hz

Size & Weight:

91 x 251 x 291mm; 2.2kgAccessories included:

Power cord (UK and Continental Europe), BNC to crocodile clip test lead and instructions

Common Information



513-8510 GFG2004 Series Function Generator 0.1Hz - 4MHz


671-8906 GFG2020 Series Function Generator 1Hz - 20MHz


671-8915 GFG2120 Series Function Generator 1Hz - 20MHz

376-0200 GFG 8216 Series Function Generator 0.3Hz - 3MHz

398-5364 GFG 8219 Series Function Generator 0.3Hz - 3MHz

376-0216 GFG Series Function Generator 0.5Hz - 5MHz

ISO-TECH PRODUCT GUIDE 2012 25ISO-TECH PRODUCT GUIDE 201224 www.rs-components.com

PROGRammablE POwER SUPPlIES

For more details and calibration options, go to

PROGRammablE POwER SUPPlIES

Model IPS603 IPS405 IPS2010 IPS3202

Output Mode Switching Linear

Output power max. 200W 200W 200W 158W

CH1 CH1 CH1 CH1 CH2 CH3

Voltage 0 - 60V 0 - 40V 0 - 20V 0 - 32V 0 - 32V 0 - 6V

Current 0 - 3.5A 0 - 5A 0 - 10A 0 - 2A 0 - 2A 0.5A max

Tracking series voltage – – – 0 - 64V –Tracking parallel current – – – 0 - 4A –

Constant Voltage Operation

Load regulation ≤ 10mV ≤ 3mV

Line regulation ≤ 0.05% ≤ 3mV

Ripple ≤ 20mVrms ≤1mVrms

Constant Current Operation

Load regulation ≤ 5mA ≤ 3mA

Line regulation ≤ 0.05% ≤ 3mA

Ripple ≤10mArms ≤ 3mArms

Programming Voltage 20mV 10mV 10mV 10mV

Resolution Current 2mA 2mA 5mA 1mA

IPS DC SERIES DC power supplies with a digitized programmable interface enabling keypad setup or access through RS232 interface to provide remote control and ATE capability. Setting store/recall memory ideal for automated operation and production testing.

• Spin wheel setting of voltage, current• Wide Input Voltage Range and high

power factor • High Efficiency and high power density• Over-Voltage, Over-Current,

Over-Temperature Protection• Rear panel OUTPUT and SENSE terminals• Output ON/OFF Control

Size & Weight:

IPS2035 & 3620: 188 x 141 x 388mm; 6.2kgIPS2050 & 4630: 268 x 141 x 388mm; 9.3kgPower:

90V - 250V ac, 50/60HzAccessories included:

Output lead cover kit, mains lead cover kit & user manual

Common Information

446-1594 IPS 603 200W, 0-60V Programmable Power Supply

446-1601 IPS 405 200W 0-40V Programmable Power Supply

446-1617 IPS 2010 200W 0-20V Programmable Power Supply

513-4653 IPS 3202 158W Linear Power Supply

Model IPS 2035 IPS 3620 IPS 2050 IPS 3630

Output

Output power max. 700W 720W 1000W 1080W

Voltage 2 - 20V 3 - 36V 2 - 20V 3 - 36V

Current 0 - 35A 0 - 20A 0 - 50A 0 - 30A


Load regulation ≤ 0.1% + 5mV ≤ 0.1% + 5mV

Line regulation ≤ 0.05% + 5mV ≤ 0.05% + 5mV

Ripple ≤ 10mVrms ≤ 10mVrms


Load regulation ≤ 0.2% + 10mA ≤ 0.2% + 15mA

Line regulation ≤ 0.2% + 10mA ≤ 0.2% + 15mA

Ripple ≤ 0.2% + 20mArms ≤ 0.2% + 40mArms

Programming Voltage 10mV 10mV 10mV 10mV

Resolution Current 10mA 10mA 20mA 10mA

513-4978 IPS2035 700W Programmable Power Supply




IPS HIGH POwER SwITCHInG SERIES Four highly efficient, high power density programmable power supplies, microprocessor controlled for easy connection, via the built-in RS232 interface, to a PC for automatic testing or control purposes.

• Spin wheel setting of voltage, current & power• 100 memory STORE/RECALL of settings• Over-Voltage, Over-Current,

Over-Temperature Protection

IPS3202 additional features

• Triple output linear supply• Keypad entry of voltage, current & power • Programmable internal timer for output

ramp-up, dwell and ramp-down operation

Size & Weight:

IPS405, 603 & 2010: 255 x 100 x 305mm; 4kgIPS3202: 230 x 140 x 380mm; 10kgPower: 115/230V ±10% 50/60HzAccessories included:

Mains lead (UK and Continental Europe) and instructionsIPS3202: power cord (UK and Continental Europe), 3 x test lead sets & user manual


POwER SUPPlIES lInEaR REGUlaTIOnPOwER SUPPlIES

lInEaR POwER SUPPlIESSingle output linear regulated power supplies which can be used as a constant voltage or constant current source.

All benefit from low ripple and noise on the outputs with overload and reverse polarity protection.

• Digital LED or Analogue metered options• Low ripple and noise• Coarse and fine voltage and current controls• Separate voltage and current displays• MASTER/SLAVE model options enable 2

power supplies to be connected in series or parallel to provide double the voltage or current rating

Size & Weight:

IPS1810H, 1603D: 255 x 145 x 355mm; 11.5kgIPS1820HD: 225 x 145 x 420mm; 18.5kgIPS303A, 303DD: 128 x 145 x 285mm; 5kgAccessories included:

Mains lead and instructionsPower: 100/120/220/230V±10% 50/60HzInput power (max.):

IPS1810H: 390WIPS1603D: 360WIPS1820HD: 650WIPS303A , IPS303DD: 160W

Common Information

Specifications / Ranges / Model IPS303A IPS303DD IPS1603D IPS1820HD

Output power max 90VA 90VA 180VA 360VA

Output ModeVoltage 0 - 30V 0 - 30V 0 - 60V 0 - 18V

Current 0 - 3A 0 - 3A 0 - 3A 0 - 20A

Display Analogue Digital Digital Digital

Mode Linear Linear Linear Linear

Master Slave operation • • – –


Line regulation ≤0.01% + 3mV ≤0.01% + 3mV ≤0.01% + 3mV ≤0.01% + 3mV

Load regulation ≤0.01% + 3mV ≤0.01% + 3mV ≤0.02% + 5mV ≤0.02% + 5mV

Ripple & noise ≤0.5mVrms ≤0.5mVrms ≤1mVrms ≤1mVrms


Line regulation ≤0.2% + 3mA ≤0.2% + 3mA ≤0.2% + 3mA ≤0.2% + 3mA

Load regulation ≤0.2% + 3mA ≤0.2% + 3mA ≤0.2% + 3mA ≤0.2% + 3mA

Ripple & noise ≤3mArms ≤3mArms ≤3mArms ≤5mArms


mUlTI-OUTPUT lInEaR POwER SUPPlIES Ideal for analogue circuit applications such as operational amplifiers, push-pull stages and logic circuits where closely tracking dual rail voltages are required.All benefit from low ripple and noise on the outputs with overload and reverse polarity protection.Three modes of operation: • Tracking • Auto series • Auto parallel

Independent outputs: Output voltage and currents are controlled separately and isolated from each other and from the chassis.

446-1645 IPS2303 2 Channel 180W Linear Power Supply



684-2998 IPS3303S Multiple output high precision programmable linear DC power supply

684-2992 IPS3303D Multiple output programmable linear DC power supply

• 4 x 3 digit LED displays• Low ripple and noise• Tracking operation and automatic Series /

Parallel operation• Output ON/OFF switch• Output Voltage and current setting with

output disabled• Fan speed control to minimise fan noise• Isolated outputs

Size & Weight:

255 x 145 x 265mm; 7kgPower:

100V/120V/220V±10%, 230V ac ±10% 50/60HzAccessories included:

Mains lead and instructions

Common Information


Model IPS-2303 IPS-3303 IPS-4303

200W

CH1 CH2 CH3 CH4

0 - 30V 2.2 - 5.2V 8 - 15V

0 - 3A 1A max 1A max

0 - 60V–

0 - 6A

180W

CH1 CH2

0 - 30V

0 - 3A

0 - 60V

0 - 6A

Power

Output Mode

Voltage

Current

Tracking series voltage

Tracking parallel current

Constant Voltage Operation (Ch1, Ch2)

Line regulation ≤ 0.01% + 3mV

Load regulation ≤ 0.01% + 3mV (Rating current ≤ 3A)

Ripple & noise ≤ 1mVrms, 5Hz - 1MHz

Constant Current Operation (Ch1, Ch2)

Line regulation ≤ 0.02% + 3mA

Load regulation ≤ 0.02% + 3mA

Ripple & noise ≤ 3mArms

195W

CH1 CH2 CH3

0 - 30V 5V fixed

0 - 3A 0 - 3A

0 - 60V–

0 - 6A

Model IPS-3303D IPS-3303S

Power

Output Mode

Voltage

Current

Tracking series voltage

Tracking parallel current

Constant Voltage Operation (Ch1, Ch2)

Line regulation ≤ 0.01% + 3mV

Load regulation ≤ 0.01% + 3mV (Rating current ≤ 3A)

Ripple & noise ≤ 1mVrms, 5Hz - 1MHz

Constant Current Operation (Ch1, Ch2)

Line regulation ≤ 0.02% + 3mA

Load regulation ≤ 0.02% + 3mA

Ripple & noise ≤ 3mArms

195W

CH1 CH2 CH3

0 - 30V 2.5/3.3/5V

0 - 3A 3A fixed

0 - 60V –

0 - 6A –

195W

CH1 CH2 CH3

0 - 30V 2.5/3.3/5V

0 - 3A 3A fixed

0 - 60V –

0 - 6A –

201-3424 IPS303A 90VA Analogue Power Supply

325-6004 IPS303DD 90VA Digital Power Supply

204-729 IPS1603D 180VA Digital Power Supply

513-4962 IPS1820HD 360VA Digital Power Supply

ISO-TECH PRODUCT GUIDE 2012 29For more details and calibration options, go toISO-TECH PRODUCT GUIDE 201228

POwER SUPPlIES DC SwITCHInG

www.rs-components.com

CalIbRaTIOn & COmPOnEnT TEST

IlC421 CURREnT/VOlTaGE CalIbRaTORToolbox instrument providing four essential functions for calibrating current loops, process devices and measuring process signals

• Current calibrator drives loads up to 500Ω• Current measurement• Power and measurement of 2 wire loop currents• Precision mV dc source• Sampling time 0.4 seconds (approx.)

ICT76 COmPOnEnT TESTERAn essential tool box instrument for the maintenance and repair engineer. Use the ICT76, to measure the value of resistors and capacitors, check battery conditions and test diodes, LEDs, transistors and SCRs.

• hFE and ICEO current measurement in transistors• Direct voltage measurement in diodes and LEDs• Validity or defect test for SCRs• Battery load test

lCR821 & lCR819 lCR mETERSAutomatic, user programmable LCR meters for precision measurement of impedance parameters.

• Inductance, capacitance and resistance measurement• Dissipation and quality factor readings• Simultaneous display of test conditions and results on backlit dot matrix LCD• Absolute, ΔValue and Δ% measurement display• STORE/RECALL up to 100 setup configurations• RS232 port and communication software

Range Display resolution Accuracy

Current source0 - 19.99mA 0.01mA ±(0.25% FS + 1d)

0 - 24mA 0.1mA ±(0.5% FS + 1d)

Current measurement0 - 19.99mA 0.01mA ±(0.25% FS + 1d)

0 - 24mA 0.1mA ±(0.5% FS + 1d)Power & current measurement of two wire loop

0 - 19.99mA 0.01mA ±(0.25% FS + 1d)

0 - 24mA 0.1mA ±(0.5% FS + 1d)

DC mV source -199.9mV to 199.9mV 0.1mV ±(0.25% FS + 1d)

Size & Weight:78 x 185 x 38mm; 265gPower:9V PP3 batterySupplied accessories:Test leads with crocodile clips, alkaline battery and instructions. Optional accessories:Replacement leads: 379-246

Size & Weight:84 x 174 x 31mm; 330gPower:9V PP3 batterySupplied accessories: Test leads, alkaline battery and instructions

Size & Weight:330 x 149 x 437mm; 5.5kgPower: 230V ±10% 50/60HzSupplied accessories: 4 wire kelvin leads and clips, RS232, software on CD-ROM and instructions

701-2814 ILC 421

687-5282 ICT76

Resistance Capacitance Battery Load Test

Range 200Ω - 20MΩ 200.0pF - 20mF 9V: 15mA

Resolution* 0.1Ω 0.1pF 1.5V (AA, C or D): 150mA

Basic accuracy* ±(0.75% + 4d) ±(0.5% + 1d) 1.55V button cell: 0.8mA

ICEO hFE hFE base current hFE Vce

Range 10nA - 20µA 1 - 1000 ~100µA ~3V

* varies across measurement ranges

Test frequency12Hz - 100kHz (LCR819) 503 steps12Hz - 200kHz (LCR821)

Basic accuracy ±0.05%

Resistance range 0.00001Ω - 99999kΩ

Capacitance range 0.00001pF - 99999µF

Inductance range 0.00001mH - 99999H

Quality factor 0.0000 - 9999

Test modes R/Q; C/D; C/R; L/Q

SwITCHED POwER SUPPlIESSingle output switching dc power supplies which can be used as a constant voltage or constant current source.

High regulation is maintained at 0.01% and remote sensing adds an extra level of precision by compensating for cable losses between loads.The lightweight and high efficiency of these power supplies make them an ideal solution for bench-top or portable applications requiring high regulation.

• Lightweight, high power efficiency design • Constant Voltage and Constant Current

Operation • Coarse and fine voltage and current controls• Separate voltage and current displays• High Power Density • Over Voltage, Overload and Reverse

Polarity Protection • Remote Output ON/OFF control

Size & Weight:

128 x 145 x 285mm; 3.3kgAccessories included:Mains lead, 4 Amp test lead set and instructionsPower: 115V/230V±15% 50/60HzInput power: 500W max.

Common Information

Specifi cations / Ranges / Model IPS606D IPS1820D IPS3610D

Output power max 90VA 180VA 360VA

Output ModeVoltage 0 - 60V 0 - 18V 0 - 36V

Current 0 - 6A 0 - 20A 0 - 10A

Display Digital Digital Digital

Mode Switching Switching Switching

Master Slave operation • – –


Line regulation ≤ 5mV ≤ 5mV ≤ 5mV

Load regulation ≤ 5mV ≤ 5mV ≤ 5mV

Ripple & noise ≤0.5mVrms ≤5mVrms ≤1mVrms


Line regulation ≤ 3mA ≤ 3mA ≤ 3mA

Load regulation ≤ 3mA ≤ 3mA ≤ 3mA

Ripple & noise ≤3mArms ≤10mArms ≤5mArms


357-0782 IPS606D 90VA DC Power Supply



455-198 LCR 821

433-9784 LCR 819

666-6445 Kelvin Clip Test Leads

666-6457 Test Fixture Two-Wire with Alligator Clips

513-6081 Test Fixture (Tweezers) for SMD/Chip Components

513-6097 Test Fixture for SMD/Chip Components - Size range from 0603 to 1812

666-6451 Test Fixture for SMD/Chip Components - Size range from 0201 to 0805

ISO-TECH PRODUCT GUIDE 2012 31ISO-TECH PRODUCT GUIDE 201230 www.rs-components.com

SOUnD lEVEl mETERS

For more details and calibration options, go to

EnVIROnmEnTal mOnITORInG

SlC1356 SOUnD CalIbRaTORAn easy to use instrument for the calibration of sound level meters. The socket accepts 1”, 1/2” and 1/4” diameter microphones for use with most standard microphone models used in acoustical studies.

Applicable standards ANSI S1.40 – 1984 / IEC 942 1988 Class 2

Output sound pressure level 94dB / 114dB (Reference 20µPa)

Output frequency 1000Hz ± 4%

Temperature coeffi cient 0.015dB

Total harmonic distortion <3%

Accuracy ± 0.5dB

Applicable standardANSI S1.25-1991 A weighting, ISO-1999,BS6402: 1983

Noise DOSE range 0.01 – 9999%

Criteria level (selectable) 80 / 84 / 85 / 90dBA

Measurement threshold level 70 – 90dBA 1dB step

Measurement range 70 – 140 dBA

Exchange rate (EA) 3 / 4 / 5 / 6dBA

Accuracy ±1.5dBA

Frequency rating A

Frequency response 20Hz - 10kHz

Time constant F (FAST); S (SLOW)

Size & Weight: 103 x 63 x 54mm; 200gPower: 1 x 9V PP3 batterySupplied accessories: Battery, carry case, 1/2”& 1/4” microphone adaptors and instructions

697-3828 SLC1356

nDm SERIES PERSOnal nOISE DOSImETERSPersonal noise dosimeters for evaluating accumulated noise exposure in the working environment. They are designed for carrying out unsupervised noise exposure assessments of personnel moving between areas of varying noise levels, and feature Exchange Rate settings to match local legislative noise doubling dB values.

The NDM1355 additional features:• 5 event data storage, each event captures:-• %DOSE, 8 hour %DOSE, PEAK & RMS flags, exposure time, peak time & peak event duration• RS232 interface for download of data to a PC• Real time clock.

Size & Weight;106 x 60 x 34mm; 350g. Power:4 x AAA batteriesSupplied accessories:NDM1354: Batteries, adjustment screwdriver, carry case and instructionsNDM1355: Batteries, adjustment screwdriver, PC software, RS232 cable, 9 to 25 pin D connector adaptor, carry case and instructions

697-3800 NDM1354

697-3812 NDM1355

DIGITal lIGHT mETERS Compact, light meters ideal for assessing that light levels in the workplace, hospitals and offices meet the guidelines of health and safety regulations.

• CIE spectral response• Cosine correction for light & angular incidence

ElECTROmaGnETIC FIElD TESTER An EMF tester designed to provide a quick, reliable and easy way to measure electromagnetic field radiation near power lines, electronic appliances and industrial machinery.

• Triple display of X, Y & Z axis readings• Data hold and peak hold functions• Data logging up to 999 readings• RS232 interface

Model EMF1394

Measurement range2/20/200 µTesla

200/2000 milliGauss

Basic accuracy±(3% + 3d) 50 - 60Hz, ±(5% + 3d) 40 - 200Hz, -3dB @ 30 - 2000Hz

Resolution0.001/0.01/0.1µTesla

0.01/ 0.1/1 milliGauss

Bandwidth 30 - 2000Hz

Sample time 0.5s

Size & Weight: 1332: Meter 135 x 72 x 33mm; 250gSensor: 100 x 60 x 27mm1335, 1337 & RS01: Meter: 150 x 72 x 35mm; 320gSensor: 92 x 60 x 29mmPower: 1332: 1 x 9V PP3 battery1335, 1337 & RS01: 6 x AAA batteriesAccessories included: 1332A Battery, carry case and instructions1335, 1337 & RS01 carry case and instructions

Size and weight:

155 x 72 x 35mm; 165gAccessories included:

Battery, RS232 interface cable, Windows compatible connection software and instructionsPower: 6 x AAA batteries

Common Information

Common Information

697-3853 EMF1394

Model ILM1332 ILM1337 ILM1335 ILM-01

Display 2000 count 2000 count 4000 count

with bargraph2000 count

Range 20.00lux - 200.0klux 20.00lux - 20.00klux 40.00lux - 200.0klux 50.00lux - 50,000lux

Basic accuracy ±(3% + 0.5%full scale)

Resolution 0.1lux 0.01lux 0.01lux 0.01lux

Analogue output • – – –Display HOLD • • • •PEAK hold – – • –MIN/MAX recording – – • •Relative mode – – • –Measurement rate 2 times/sec 2.5 times/sec 1.3 times /sec 2.5 times/sec

Repeatability ±2% ±2% ±2% ±2%

Analogue output 2V at full scale – – –

697-3847 697-3850697-3834 697-3822


Slm52, Slm1352n & Slm1353m SOUnD lEVEl mETERSFully meets the requirements of safety, health and industrial safety officers for sound level measurements. The 1352N & 1353M extra features are ideal for long term monitoring and analysis.

Applicable standardsIEC61672-1: 2003 Class 2; IEC60651: 1979 Type 2; ANSI S1.4: 1983 Type 2

Digital display 4 digit LCD, 0.1dB resolution

Measurement level 30dB - 130dB

Measurement frequency range 31.5Hz - 8kHz

Frequency weighting A and C

Time weighting Fast and Slow

Microphone 1/2 inch Electret condenser microphone

Measurement level range(5 ranges in 10dB steps)

30 - 90dB, 40 - 100dB, 50 - 110dB,60 - 120dB, 70 - 130dB

Analogue bar indicator 1dB steps, 60dB display range

Manual data memory capacity 32000 sets (SLM1352N & SLM1353M), 99 sets ( SLM52N)

Analogue ac/dc output 1Vrms ( at full scale ), 10mVdc / dB

Size & Weight: 265 x 722 x 36mm; 380gPower: SLM52N: 9V PP3 SLM1352N & 1353M: 4 x AAA batteries or external 5-12Vdc @10mASupplied with:Batteries, adjustment screwdriver, windshield, 3.5mm analogue output plug, carry case & instructionsSLM1352N only: PC software, RS232 cableSLM1353M only:PC software, USB cable

• 1/2 inch electret condenser microphone• Fast and Slow time weightings.• A and C frequency weightings.• Over and under limits alarm setting facility• MAX hold function• STORE/RECALL of 99 sets of readings• Analogue output for connection suitable for use

with a frequency analyzer, level recorder, FFT analyzer, and graphic recorders.

SLM 1352N & SLM1353M additional features • 32000 Records data logging function• PC interface for downloading records

(SLM1352N: RS232, SLM1353M: USB)• Real time clock (date & time)

SLM 1353M additional features

• Integrating sound level meter• Equivalent continuous sound pressure level

(Leq), Sound exposure level and percentile level measurement

• Simultaneous Maximum and Minimum level measurement display.

• Impulse/Fast/Slow dynamic characteristic• Sound level alarm output

697-3803 SLM52N

697-3799 SLM1352N

725-5591 SLM1353M

For more details and calibration options, go toISO-TECH PRODUCT GUIDE 201232

PHOTOVOlTaIC CEll & baTTERy TESTERS

ISm400 & ISm410 SOlaR POwER mETERS• Total solar energy against elapsed time or average solar energy per hour calculation• Determines the percentage solar power transmission through glass, heat insulation materials,

sunshades etc.• Select either W/m2 or Btu / (ft2 x h) units• Data HOLD/MAX/MIN/AVG modes• Manual Data Memory and Read function. (99 sets)• Auto data memory and RS232 to PC interface ( ISM410 only)

IbT330 baTTERy TESTER• Dedicated battery tester for lead–acid, NiCD, NiMH & Lithium-ion rechargeable

batteries up to 1200Ah• Simultaneous measurement and display of battery resistance, voltage, current & temperature. • Compares battery condition with up to 99 user set resistance and voltage limits• 4 wire probe type test leads and crocodile clip leads with temperature sensor for accurate

4-terminal measurement• Clamp adaptor for DC current measurements.• Data logging function and RS232 interface

ISm490 PHOTO VOlTaIC CEll analySER• I-V Curve test & display for Photo voltaic cells• Single Point I-V Test.• Maximum solar power (Pmax): maximum voltage and maximum current at Pmax measurements• Voltage at open circuit (Vopen)• Current at short circuit (Ishort).• Efficiency (%) calculation of solar panels• RS232C cable for PC.

Size & Weight:135 x 90 x 18mm; 135g Accessories included: 4 AAA batteries, tripod mounting screw & instructions. Download-ing software & RS232 interface cable (ISM410)Power: 4 x AAA batteries

Size & Weight:198 × 94 × 49mm: 530g (meter) 193 × 69 × 31mm: 240g (clamp adaptor)Accessories included: Clip type test lead with temperature sensor, Probe test lead, DCA current adaptor, Zero adjustment board, Instruction manual, batteries, AC adaptor, Optical RS232 cable, CD PC software & carrying case.

Size & Weight: 257 x 155 x 57mm; 1160g (with battery)Accessories included: 8 NiMH rechargeable batteries, ac mains adaptor, 6A Kelvin test clips set, instructions, downloading software & RS232 interface cable

Range 2000W/m2

Accuracy ±10W/m2 or ±5% whichever is the greatest

Resolution 0.1W/m2

Spectral Response 400 - 1000nm

Display 4 digit LCD display

Volts dc Current dc

Range 0 - 60V 0 - 6A

Accuracy ±1% ±1%

Resolution 1mV 0.1mA

Volts dc Resistance Temperature Current dc


6V, 60V±(0.1% + 6d)1mV, 10mV

4mΩ - 400Ω±(0.8%+ 6d) 1µΩ

-20ºC to 60ºC ±1ºC0.1ºC

0.6A – 600A±(2% + 2d)0.1A

688-9155 ISM490

683-1263 ISM400

683-1267 ISM410

686-2201 IBT330

736-1753 IBT300 Replacement leads, probe type

736-1762 IBT300 Replacement leads, alligator clips type

Business

ISO-TECH