View
248
Download
0
Category
Preview:
Citation preview
7/23/2019 Welding Products(Pg164-180) (1)
http://slidepdf.com/reader/full/welding-productspg164-180-1 1/1764
Allinton Engineering & Trading Pte Ltd Head Ofce: 331 Jalan Besar, Singapore 208983. 6296 0679 (10 lines) 6297 0024
Branch Ofce: 21 Tuas Basin Link Singapore 638782 6265 1888 (10 lines) 6265 5623www.allinton.com.sg allinton@singnet.com.sg sales@allinton.com.sg
Wind Yama Portable Ventilator
AS00003
AP-200Portable VentilatorSize: 8”
Rotation: 3460rpmHP: 150WVoltage: Single Phase 110V, 220V Three Phase 220V, 380V
AP-300Portable VentilatorSize: 12”
Rotation: 3460rpmHP: 550WVoltage:Single Phase 110V, 220VThree Phase 220V, 380V
AS00004Features1. Aluminium blades compact in size, easy to operate.2. Single-phase condensor motor eliminates the problems of over-heating of three-phase motors.3. Aluminium blades have been subject to balance correction with computer.
For Use In1. Underground tunnels shipyards honeycomed locales & narrow places.2. To suck away toxic gases when welding and keep air fresh.3. Perfect for storage compartments, warehouse and electric cable
construction sites.
Code No. Model No. Weight Voltage P Hz m³/min m/Aq r.p.m pH kg
AS00003 AP-200 150 110 & 220 2 50 25 35 2.930 1pH 10.360 30 42 3460
AS00004 AP-300 550 110 & 220 250 60 40 2.930
1pH 19.760 70 50 3460
Ventilation Hose (5 MTR/10 MTR)
AS00016
Flexible DuctDia:From 180m/m - 1000m/mLength Measure:From 1m - 20m
Connection Flexible DuctEasily fitted extensions can extend the duct. Simplyslip the extension over the ring on the end of theduct and securely tie the cord
5 MTR
Code No. Size
AS00016AS00017AS00018AS00019AS00020
AS00021AS00565
200mm/8”300mm/12”350mm/14”400mm/16”500mm/20”
600mm/24”800mm/32”
10 MTR
Code No. Size
AS00366
AS00367AS00368AS00369
AS00370AS00566AS00574AS00575
200mm/8”AS00124 250mm/10”
300mm/12”400mm/16”500mm/20”
600mm/24”800mm/32”900mm/36”1000mm/40”
WIND YAMAWIND YAMA WEV 400 16” and WEV 600 21” variable speed turbo blowers offermore power, higher performance, no CO and are GFCI–compatible, too!
You Control The 1.5HP Force•
From full PPV for fast clearance of dangerous smoke and gases to slower speedsfor cooling overheated firefighters is as easy as turning the control knob on the
control panel. IntelliSense™ Controls The Start Up Power •
This exclusive water–resistant electronic control feature monitors and limits theamount of start up power to allow operation on GFCI Circuits and for starts ongenerators as small as 2kW.
Specifications
Code No. Model No. HP Dimensions Motor MFG/Model No. Wt RPM Set Back Angle Airflow
AS00355AS00356
WEV400-16”WEV600-21”
1.51.5
23H x 17W x 16D24H x 18W x 24D
YM-EM-F1.5-90YM-EM-F1.5-90
7480
35883588
6’8’
20°13°
9,705 CFM11,061 CFM Tilt Adjustment helps you
quick direct the FORCE
23”
Compartment friendly size and shape
17”
16”Deep
Welding Products
7/23/2019 Welding Products(Pg164-180) (1)
http://slidepdf.com/reader/full/welding-productspg164-180-1 2/17165
Allinton Engineering & Trading Pte Ltd Head Ofce: 331 Jalan Besar, Singapore 208983. 6296 0679 (10 lines) 6297 0024
Branch Ofce: 21 Tuas Basin Link Singapore 638782 6265 1888 (10 lines) 6265 5623www.allinton.com.sg allinton@singnet.com.sg sales@allinton.com.sg
Onishi Portable FanMAMA-TA
Remove Hot Air and Harmful Gases and Supplies Fresh Air and Oxygen. The machinehas made many safe and comfortable working environments.
Feature1. The breaker of motor is fitted to prevent the motor from burning out.2. Portable type, convenient to carry.3. The ideal-bell mouth type casing has high efficiency and low noise.4. Our unique water-proofed switch is very durable.
* Uses
removing harmful gases andsupplying fresh air
ventilation and reduction ofhigh temperatures
manhole ventilation
*WIN MAMA–TD outline dimension.
Item Name
12345678910
MotorFitting Plate
HandleImpeller
Wire NetCasingSwitchGlandRubberCable
*Particulars
Code No.Casing
DiaVolt(V)
Output(kW)
RPM(rpm)
Freq.(Hz)
QuantityPress
mmAqRating
Weightkg
AS00005 280 100/200 0.55 3000/3600 50/60 70cu.m/min 30 Cont 18
* Distribution of Wind Velocity at 60Hz
WIN MAMA-TC
Flexible duct are over tape type and sewing type.
WA2-2, WA2-5
Light Weight, Solid, Powerful Fan. The quality has been proved by the 30-yearhistory.
Feature1. The weight is lighter than ordinary fan.2. The one-piece motor makes maintenance much easier.3. Great care has been taken to prevent noise and danger and we recommend
the equipment as a reliable product.4. The equipment has the capacity of wind which ordinary portable fan cannot
get.
* UsesWelding work, Manhole ventilation (removing harmful gases and supplyingfresh air and oxygen) Ventilation of tanks and reduction of high temperature.Flexible ducts (over tape type and sewing type) are connected easily.
W i n A c e C h a r a c t e r i s t i c C u r v e
Item Name
12345678
CasingImpellerMotor
Fitting PlateTerminal Box
HandleWire NetRubber
*Particulars
Code No. Type Output RPM Freq Capacity Press Weight A D H h W Q L P l gland
AS00006AS00007
WA2–2WA2–5
1.5kW3.7
3000/60003000/3600
50/60Hz50/60
80cu.m/min150
50mmAq70
35kg64
400dia.500
436dia.536
556656
272322
370470
300400
436506
300350
6878
20C25A
AS00005
AS00006
JAPAN
Welding Products
7/23/2019 Welding Products(Pg164-180) (1)
http://slidepdf.com/reader/full/welding-productspg164-180-1 3/1766
Allinton Engineering & Trading Pte Ltd Head Ofce: 331 Jalan Besar, Singapore 208983. 6296 0679 (10 lines) 6297 0024
Branch Ofce: 21 Tuas Basin Link Singapore 638782 6265 1888 (10 lines) 6265 5623www.allinton.com.sg allinton@singnet.com.sg sales@allinton.com.sg
Onishi Explosion Proof Fan
AS00008dimension for
BM-B
Features1. The Lightest Weight: BM-B---------25 KG
BB-B ---------14.5 KG2. Safety: Exp. Proof Grade d2G4. Non-Sparking Type
3. Useful: Fitting with a Exp. Proof Switch Cabtire.Cable 5M Length
Particulars
Code No. Type Dia:mm Output Source Quantity Pressure Weight
AS00008 BM-B 300 0.55kW1 Ø 50 / 60Hz
0.18kW
AC100V 70m³/min 30mmAq 25kg
AS00009 BB-B 200 AC230V 20m³/min 20mmAq 14kg
Blowers
AS00354
Portable Pneumatic Ventilator
Model: KMA300F 12” orKMA400F 16”Dia: 12” or 16”Intrinsic Safe for HazardousEnvironmentsISSA: 59 14 25 & 26
AS00353
Portable Fan
AS00623 AP-7 600mm/24” 3.0HP/230V/50Hz 1400 RPM Single 290m3/min
Code No. Model Size Power Max RPM Speed Max Rated
AS00631 AP-7 600mm/24” 3.0HP/415V/50Hz 1400 RPM 3Phase 290m3/min
AS00623
Jumbo Axial Fan Portable Fan
Code No. Model Size Power Max RPM Speed Max Rated
AS00624
Explosion Proof Electric Blower
Model:Dia:
AES200mm 8” AES300MM 12”200mm (8”), 300mm (12”)
Voltage:Phase:
115 / 230Single
Anti–static ABS Housing, Chemical Resistant UL Class I, Group D &Class II, Group E, F, G. RAMFAN, USA
Pneumatic Blower
Model: AAF 300MM 12” Dia: 12”Anti–static ABS Housing, Chemical Resistant, USA
AS00323 AES 8”AS00324 AES 12”
AS00325 AAF 12”
AS00628
AS00628 AP-5 400mm/16” 2.0HP/230V/50Hz 2800 RPM Single 128m3/min
AS00629 AP-6 500mm/20” 2.2HP/230V/50Hz 2800 RPM Single 138m3/min
AS00630 AF-6 500mm/20” 2.2HP/415V/50Hz 2800 RPM 3Phase 138m3/min
Code No. Model Size Power Max RPM Speed Max Rated
AS00624 AP-2 200mm/8” 1/4HP/230V/50Hz/60Hz 2800 RPM Single 25m3/min
AS00625 AP-3 300mm/12” 1/4HP/230V/50Hz/60Hz 2800 RPM Single 63m3/min
AS00627 AP-4 350mm/14” 1.0HP/230V/50Hz/60Hz 2800 RPM Single 82m3/min
KMA300F 12” KMA400F 16”
Welding Products
7/23/2019 Welding Products(Pg164-180) (1)
http://slidepdf.com/reader/full/welding-productspg164-180-1 4/17167
Allinton Engineering & Trading Pte Ltd Head Ofce: 331 Jalan Besar, Singapore 208983. 6296 0679 (10 lines) 6297 0024
Branch Ofce: 21 Tuas Basin Link Singapore 638782 6265 1888 (10 lines) 6265 5623www.allinton.com.sg allinton@singnet.com.sg sales@allinton.com.sg
Water Driven Turbine Fan
Model:
Dia:
ATF 12” or ATF 16”300mm/12”, 400mm/16”
Dia:
Phase:
12” & 16”Single
Water Connection: 2½” NST
Pneumatic Blower – Blower / Exhauster
Tornado Electric Blower (Explosion Proof)
Model: 8AXP, 12AXPThe Explosion Unit is approved and certified by American Bureauof shipping (ABS) Ideal for exhaust applications Prime–Air, USA
Venturi Air Blower (Air Mover)
Model: ARV760, ARV760S, ARV1500High output, Lightweight, Portable anti–static, Crush Proof Conductive Polymer Diffuser.Weather Proof and Chemical Resistant. Powered by compressed air or saturated steamRAMFAN. USA.
Hurricane Venturi Blower
Model: AHV3P, AHV3, AHV6, AHV8, AHV10The Explosion Unit is approved and certified by American Bureauof shipping (ABS) Ideal for exhaust applications Prime–Air, USA
Air Driven Gas Freeing Fan
Model:
Air Inlet:
AGFF 12” or AGFF 16”3/4” or 1” NPT
Dia: 12” & 16”
AS00328 ATF 12”
AS00329 ATF 16”
AS00332 8AXP
AS00333 12AXP
AS00334 AHV 3P
AS00335 AHV 3
AS00336 AHV 6AS00337 AHV 8
AS00338 AHV 10
AS00339 ARV-760
AS00340 ARV-760S
AS00341 ARV-1500
AS00330 AGFF-12AS00331 AGFF-16
AS00327 AET-20
AET - Industrial Fan
24” Industral Wall FanAS00025
26” Industral Stand FanAS00024
20” Industral Desk FanAS00022
Code No. Model Description
AS00326 AET - 12AET - 16AET - 20AET - 24
12” Jet Fan16” Jet Fan20” Jet Fan24” Jet Fan
AS00701AS00327AS00702
Code No. Size
AS00027 20”24”26”
AS00025AS00026
Code No. Size
AS00022 20”
Code No. Size
AS00028 20”24”26”
AS00023AS00024
Description:This four-bladed vaneaxial fan is called a Jet Fan because ahighvelocity jet of compressed air is ejected from the trailingedge of the blade, as shown in the diagram. This results inthe forward rotation of the fan wheel just like a jet plane ispushed forward by the high-velocity jet ejected from the rearof the jetengine.
• Use for general ventilation in any location wherecompressed air is available. Use as blower or exhauster.
• Suited for ventilation of tanks, process vessels, or otherconfined areas for the removal of hazardous fumes orcontaminated air from welding, sandblasting and otheroperations.
• Rated operating pressure 40-110 PSI.• Design allows for lower RPMs while still moving more air.
• Bearings are packed with a hi-tech synthetic lubricant forlonger life.
• Propeller precision balanced by removing material fromend of blades.
• Use as blower or exhauster.
• Electro polished stainless steel fan guard.• Heat treated to T6 aircraft aluminum specifications.• Super-duty, high quality, high pressure air seal for longer
service.• Heaviest-duty fan in the industry.• Hi-tech four blade design.• Guide vanes to eliminating turbulence which smooths air
flow and increases effeciency.• Fan design by one of the foremost fan engineers in the
world.
Welding Products
7/23/2019 Welding Products(Pg164-180) (1)
http://slidepdf.com/reader/full/welding-productspg164-180-1 5/1768
Allinton Engineering & Trading Pte Ltd Head Ofce: 331 Jalan Besar, Singapore 208983. 6296 0679 (10 lines) 6297 0024
Branch Ofce: 21 Tuas Basin Link Singapore 638782 6265 1888 (10 lines) 6265 5623www.allinton.com.sg allinton@singnet.com.sg sales@allinton.com.sg
Welding CableBlack
AS00105AS00106AS00107AS00108
300AMP400AMP500AMP600AMP
Welding CableOrange
AS00109AS00110AS00111AS00112
300AMP400AMP500AMP600AMP
Black NeopreneCable
AS00113AS00114AS00115
–
300AMP400AMP500AMP
–
Orange NeopreneCable
AS00116AS00117AS00118
–
300AMP400AMP500AMP
–
5. Specification
Nominal areaof conductor
mm
Conductive coreNo. of wire x Dia.
mm
Max. overallDia. of cable
mm
Approx. weightof cablekg/km
Max. D.C. resistance of conductorat 20°C not more than rad./km
tinned untinned
101625
35507095120150185
322/0.20513/0.20798/0.20
1121/0.201596/0.202214/0.202997/0.201702/0.202135/0.301443/0.40
9.711.513.0
14.517.019.522.024.027.029.0
140212308
423592828
1088137416662044
1.911.16
0.758
0.5360.3790.2680.1980.161
0.15290.1069
1.951.19
0.780
0.5520.3900.2760.2040.1640.1320.108
Welding Cable
Main Productsbare wiresmagnetic wiresrubber insulated electric wiresplastics insulated electric wirestough rubber sheathed arc welding electrode cabletough rubber sheathed flexible cables for general purposesPVC-insulated & PVC - sheathed power cablePVC-insulated & PVC - sheathed control cablePVC-insulated & PVC - sheathed signal cable
AS00115
AS001183 2 1
Flexible Copper - core cable for welding machines1. Application–The product is applied up to A.C 200 V and pulsating D.C. 400V at the
secondary of welding machine against the earth and connecting welding guns. TheMax. continuous operating temperature of conductor is 65ºC.
2. Type YH3. Standard of Product–The product verified by CCEE accors with the demands of GB
5013.3 85 (equal to IEC 245)4. Construction
1. conductor of the cable
3. rubber insulated sheath
2. isolated layer lapped thermo-resistantfilm or other fiber tapes
Code No. Model Code No. Model Code No. Model Code No. Model
Code No. AS00091 AS00092 AS00093 AS00094 AS00095
Size(mm) 4.5 x 305 5.0 x 305 6.5 x 305 8.0 x 305 9.0 x 305
Code No. AS00641 AS00642
Size(mm) 1.5 2.5
Code No. AS00660 AS00661 AS00662
Size(mm) 2.5 x 350 3.2 x 350 4.0 x 400
Code No. AS00663 AS00664 AS00665
Size(mm) 2.5 x 350 3.2 x 350 4.0 x 400
Code No. AS00666 AS00667 AS00668
Size(mm) 2.5 x 350 3.2 x 350 4.0 x 400
Code No. AS00673 AS00674 AS00675
Size(mm) 2.5 x 300 3.2 x 350 4.0 x 350
Code No. AS00679 AS00680 AS00681
Size(mm) 2.5 x 300 3.2 x 350 4.0 x 350
Code No. AS00676 AS00677 AS00678
Size(mm) 2.5 x 300 3.2 x 350 4.0 x 350
Code No. AS00669 AS00670 AS00671 AS00672
Size(mm) 2.5 x 350 3.2 x 400 4.0 x 400 5.0 x 400
Gouging Rod Brazing Alloy Rod
CHE40Welding Rod for Mild SteelAWS A5.1 E6013
Welding Rod
CHE43Welding Rod for Mild SteelAWS A5.1 E6019
CHE56Low Hydrogen Welding Rod for High Tensile SteelAWS A5.1 E7016
CHS002
Welding Rod for Extra-low Carbon Stainless SteelAWS A5.4 E308L-16
CHS062
Welding Rod for Stainless SteelAWS A5.4 E309L-16
CHE58-1High Toughness Welding Rod for High Tensile SteelAWS A5.1 E7018-1/E7018
CHS022Welding Rod for Extra-low Carbon Stainless SteelAWS A5.4 E316L-16
Welding Products
7/23/2019 Welding Products(Pg164-180) (1)
http://slidepdf.com/reader/full/welding-productspg164-180-1 6/17169
Allinton Engineering & Trading Pte Ltd Head Ofce: 331 Jalan Besar, Singapore 208983. 6296 0679 (10 lines) 6297 0024
Branch Ofce: 21 Tuas Basin Link Singapore 638782 6265 1888 (10 lines) 6265 5623www.allinton.com.sg allinton@singnet.com.sg sales@allinton.com.sg
WELDMASTER PROTABLE MMA SERIES
The WELDMASTER PROTABLE MMA 160/200 is a single–phase DC inverter arc welding power source with Constant Current (CC) output characteristics providing the bestcombination of power, portability and convenience. Designed for STICK and High Frequency TIG welding applications.
A good welding performance is available when welding stainless, mild steels and easy start.
WELDMASTER HEAVY DUTY MMA SERIES
The WELDMASTER HEAVY DUTY MMA 300S/400S is a DC ARC Welding power supply with high performance characteristics. All the machines come standard with an arcforce and hot star t adjustment and, this power supply excellent for all types of stick electrodes, particularly the 6010 electrode. All machine ar provided with lift TIG for highquality TIG starting with no High Frequency.
A good welding performance is available when welding stainless, mild steels and easy start.
Code No. AS00528 AS00529Model No. MMA200 MMA160
Machine Specifications
Input Voltage 220V/240V 1ph 50/60Hz 220V/240V 1ph 50/60Hz
Input Current 21A (32A) 32A (42A) 15A (22A) 23A (33.5A)
Insulation Class HH
Open Circuit Voltage 62V/66V 56V/61V
Duty Cycle (40°C) 100%@200A60%@200A100%@160A
100%@160A60%@160A
100%@125A
Welding Current 10–200A 10–160A
Load Voltage 18V 28V 16.4V 26.4V
Protection Class 12PI12PI
Dimensions (L x W x H) 420 x 160 x 265mm 420 x 160 x 265mm
Weight gk21gk5.21
Code No. AS00530 AS00531
Model No. MMA 300S MMA 400S
Machine Specifications
Input Voltage 380V/415V 3ph 50/60Hz 380V/415V 3ph 50/60Hz
Input Current 12.5A (16.5A) 17.2A (22.5A) 20.5A (25.3A) 26A (31.6A)
Insulation Class HH
Open Circuit Voltage 78V/85V 78V/85V
Duty Cycle (40°C) 100%@300A60%@300A
100%@250A100%@400A
60%@400A100%@350A
Welding Current 10–300A 10–400A
Load Voltage 22V 32V 26V 36V
Protection Class 32PI32PI
Dimensions (L x W x H) 550 x 300 x 490mm 550 x 300 x 490mm
Weight gk15gk94
AS00528/29
AS00530/31/32
WELDMASTER PORTABLE TIG SERIES
The WELDMASTER PORTABLE TIG 200P/200A is a single–phase DC inverter arc welding power source with Constant Current (CC) output characteristics providing the bestcombination of power, portability and convenience. Designed for STICK and High Frequency TIG welding applications.
All machine are provided with a built in gas valve, down slope, pulser and high frequency starting. A fixed preflow is provided and the current level automatically adjustspostflow. A good welding performance is available when welding stainless, mild steels and easy start.
Code No. AS00538 AS00539
Model No. TIG 200P TIG 200A
Machine Specifications
Input Voltage 220/240V 1ph 50/60Hz 220/240V 1ph 50/60Hz
Input Current 21A (32A) 23A(33.5A) 18.5A(26A)
Insulation Class HH
Open Circuit Voltage 56/61V 42/46V
Duty Cycle (40°C)60%@200A100%@160A
60%@160A100%@140A
40%@200A
60%@160A
100%@125A
Welding Current 10–200A 10–160A 10–200A
Load Voltage 18V 26.4V 18V
Protection Class 12PI12PI
Dimensions (L x W x H) 420 x 160 x 265mm 370 x 150 x 245mmWeight gk9gk21
AS00538/39
Welding Products
7/23/2019 Welding Products(Pg164-180) (1)
http://slidepdf.com/reader/full/welding-productspg164-180-1 7/1770
Allinton Engineering & Trading Pte Ltd Head Ofce: 331 Jalan Besar, Singapore 208983. 6296 0679 (10 lines) 6297 0024
Branch Ofce: 21 Tuas Basin Link Singapore 638782 6265 1888 (10 lines) 6265 5623www.allinton.com.sg allinton@singnet.com.sg sales@allinton.com.sg
WELDMASTER PLASMA CUTTER PCM SERIES
The WELDMASTER PLASMA CUTTER PCM range is an air plasma cutting power supply with Constant Current (CC) output characteristics offering the highest value. Highfrequency, gas switch and post–flow function are all build in.
A good cutting per formance is available when cutting stainless, mild steels, aluminium and easy start. A tought lightweight design makes it ideals for light industrial application.
WELDMASTE HEAVY DUTY GMAW SERIES
The WELDMASTER HEAVY DUTY GMAW POWER 500CV/500MST provides excellent arc performance with solid wire in short circuit, globular and spray transfers, and withflux or metal core wires in globular and spray transfer modes.
Standard features include; a 14–pin amphenol connector and dual auxiliary power outlets (115VAC, 5A fuse protected), solid state contactor, output votag regulation, build–inoverload protection, volt and amp meters, citater, environmental protection for optimum reliabiltity in harsh environments.
Code No. 44500SA34500SA04500SA
Model No. 001MCP08MCP04MCP
Machine Specifications
Input Voltage 220V/240V 1ph 50/60Hz 380V/415V 3ph 50/60Hz 380V/415V 3ph 50/60Hz
Input Current )A85(A15)A12(A71)A5.62(A6.81
Insulation Class HHH
Open Circuit Voltage V514 /V083V603 /V082V172 /V842
Duty Cycle (40°C)40%@40A100%@30A
A051@%001A08%001
Cutting Current A051–02A08–02A04–51
Load Voltage V041V211V69
Gas Type/ Flow Air @ 95lpm (200scfh) Air @ 190lpm (400scfh) Air @ 190lpm (400scfh)
Gas Pressure )isp07(rab8.4)isp07(rab8.4)isp07(rab8.4
Protection Class 32PI32PI12PI
Dimensions (L x W x H) 420 x 160 x 265mm 550 x 300 x 490mm 560 x 360 x 880mm
Weight gk501gk85gk21
Code No. 73500SA63500SA
Model No. POWER 500CV POWER 500MST
Machine Specifications
Input Voltage 380V/415V 3ph 50/60Hz 380V/415V 3ph 50/60Hz
Input Current 35.5A (38.5A) 35.5A (38.5A) 36A (41A) 29A (33A)
Insulation Class HH
Open Circuit Voltage V58 /V87V58 /V87
Duty Cycle (40°C)60%@500A
100%@450A60%@500A
100%@450A
Welding Current A005–03A005–03
Load Voltage 39V 39V 40V 30V
Protection Class 32PI32PI
Dimensions (L x W x H) 560 x 365 x 640mm 560 x 365 x 640mm
Weight gk07gk07
AS00540 AS00543 AS00544
AS00536/37
Welding Products
7/23/2019 Welding Products(Pg164-180) (1)
http://slidepdf.com/reader/full/welding-productspg164-180-1 8/17171
Allinton Engineering & Trading Pte Ltd Head Ofce: 331 Jalan Besar, Singapore 208983. 6296 0679 (10 lines) 6297 0024
Branch Ofce: 21 Tuas Basin Link Singapore 638782 6265 1888 (10 lines) 6265 5623www.allinton.com.sg allinton@singnet.com.sg sales@allinton.com.sg
TG2-11G Hand Pipe Gas CutterThe TG2–11G is a manually operated portable pipe cutting machine with a chain and geardrive system.The machine will exhibit excellent performance in straight and bevel cutting of all sizes ofpipes, which accounts for most of pipe cutting work, being habitually used by many users.Especially compliant for field work without power supply.
Cuts any size pipe bigger than100mm (4’)•
Ability to cut large pipe diameters (The chain for the maximum dia is 600mm)•
Low gear ration and Control valves•
Graduated bevel collar•
Light–weight and Excellent operability•
Cutt ing Thickness Up to 50mm (2”)
Pipe Cutting Diameter100~600mm (4~24”)by standard chain (2.4m = 96”) over600mm by extra chain addition
Cutting Shape I, V (up to 45°)
Drive Method Manual
Weight 10kg (22lbs)
TK-30 Semi–Automatic Gas Cutting MachineThe TK-30 is a semi–automatic (manually guided/portable) cutting machine which can beoperated freely by hand.
The excellent operability allows the machine to be used for many purposes.Light weight for single hand to operate and transport•
Speed system adjusted by rheostat, moving smoothly•
All functions are controlled by one hand. Various•
types of irregular shapes and edges cuttingare simply performedDifferent attachments are available for•
straight line cutting, circular cutting, etc.
Cutt ing Thickness 6–30mm
Cutting Speed 50–750mm/min
Power 220/50AC
Dia of Circle Cutting ƒ 50– ƒ 550mm
Dimension 455 x 400 x 225mm
Weight 9.8kg
TK-12 Beetles Portable Gas CutterThe TK-12 Beetles is a portable oxy fuel cutting machine with a high quality motor driven anda mechanical non–stage speed changer. The improved transportability will surely contributeto rationalization and labor saving of cutting operation.
The single cone system (mechanical non–stage variation device) assures constantly stable•
travel even with high temperaturesEasy operability is controlled by forward/off/reverse switch, clutch lever and speed•
adjustment knobAn adjustable radius bar for circle cutting is optionally available•
Single or Dual Torch Models, Two torch model available for parallel cutting•
2 rail suit for cutting unlimited longer part s and Groove range:•
I.Y.V. (45°)Lightness for handling and transportation•
Cutting Thickness 5~100mm (0.25~4”)
Cutting Speed 150~800mm (6~32”)/min
Speed Control Single cone system
Power 42/110/220V AC
Weight9.5kg (20.9lbs)(one torch model) 13kg(28.6lbs) (two torch model)
Size 350 x 140 x 175mm
TK-12 Max Gas CutterThe TK-12 Max is a portable flame cutting machine designed to cut straight lines, circlesand bevels with clean sharp, smooth edges providing eight standard variations of cuttingattachments. The cutting machine is intended for cutt ing materials like steel plates etc.
Excellent operability and tractive force•
Unrivaled heat–resistance and durability•
Versatility and convertibility – all types of straight line, circle, and bevel cutting•
The well–balanced center gravity ensures stable travelling•
The speed change mechanism is composed of parts designed on the basis of approx.•
5000–hour trial loaded operation particularsCutting operation can be started smoothly•
Running continuously under high temperature•
Cutting Thickness 6~100mm (0.24~4”)
Cut ti ng Speed (S tandard type) 80~800mm (3~31”)/min
Travelling Speed (High Speed type) 240~2.400mm (9~95”)/min
Speed Control Double cone stepless speed control system
Speed Meter Dial inidication (w/ conversion scale)
Power 42/110/220V AC
Machine Dimensions
Length 600mm (24”)Width 175mm (7”)Height 228mm (9”)
Max. Loading Weight 50kg (110lbs)
Weight 15kg (33lbs)
TG2-600 Circular Gas CutterThe circular cutter TG2–600 is a portable flame cutt ing machine designed to cut circle par ts,round hole and flange, smooth edges providing two standard variations of cutting speed. Thecutting machine is intended for cutting materials like steel plates, etc.
Excellent operability and lightness•
Especially for cutting of circular parts, round hole and flange•
Cutting operation can be started smoothly•
Cutting Thickness 6~100mm (0.24~4”)
Cutting Speed 0.2–6.0 R/P/min
Dia of cutting 30–600mm
Power 42/110/220V AC
Machine Dimensions
Length 750mm (29.5”)
Width 300mm (12”)Height 700mm (27.5”)
Weight 15kg
TG2-11D Automatic Pipe Gas CutterThe TG2–11D is a portable pipe cutting machine with a chain and gear drive system.The machine will exhibit excellent performance in straight and bevel cutting of all sizes ofpipes, which accounts for most of pipe cutting work, being habitually used by many users.Save working time by electric power.
Cuts any size pipe bigger than100mm (4’)•
Ability to cut large pipe diameters (The chain for the maximum dia is 600mm)•
Driven by motor with shift gear•
Graduated bevel collar•
Light–weight and Excellent operability•
Cutting Thickness 6mm–50mm
Pipe Cutting Diameter150~600mm (6~24”)by standard chain (2.4m = 96”) over600mm by extra chain addition
Cutting Shape I, V (up to 45°)
Drive Method Automatic
Voltage 220/110/47 AC
Weight 16kg
TG2-150B Profiling Gas CutterTheThe profiling cutter is a portable flame cutting machine designed to cut square, rectangle,smooth edges providing two standard variations of cutting speed. The cutting machine isintended for cutting materials like steel plates, etc.
Move and position freely by railway•
Excellent operability and lightness•
Cutting operation can be started smoothly•
Support Various kinds of spare parts•
Power 42/110/220V AC
Dimension 1190 x 335 x 870mm
Cutting Thickness 6–100mm
Cutting Speed 50–750mm/min
Dia of Circle Cutting ƒ 20–600mm
Length of Line Cutting 1200mm
Max Size of Cutting Square 500 x 500mm
Max size of Cutting Rectangle 400x900mm 450x750mm
Weight 56.5kg
TG2-11 Magnetic Pipe Gas CutterThe TG2–11 Magnetic Pipe Gas Cutter is an automatic portable gas cutting machine withpermanent magnet wheel system, can be easily set and secure on a pipe in a wide variety ofsizes. The machine will exhibit excellent performance in harsh working condition.
Can be safely fastened with the magnet wheel, compact system•
Circles can be cut in very smooth edge•
Can be working for parallel, upright and upward cutting•
Excellent for circular cutting, easy operability•
Can bevel up to 45° (IV)
Cutting Diameter >108mm
Cutting Thickness 6–50mm
Cutting Spped MM/MIN 50–750
Power 220/50 AC
Dimension 350 x 310 x 180mm
Weight 20kg
AS00632
AS00634
AS00636
AS00638
AS00639
AS00637
AS00635
AS00633
Welding Products
7/23/2019 Welding Products(Pg164-180) (1)
http://slidepdf.com/reader/full/welding-productspg164-180-1 9/1772
Allinton Engineering & Trading Pte Ltd Head Ofce: 331 Jalan Besar, Singapore 208983. 6296 0679 (10 lines) 6297 0024
Branch Ofce: 21 Tuas Basin Link Singapore 638782 6265 1888 (10 lines) 6265 5623www.allinton.com.sg allinton@singnet.com.sg sales@allinton.com.sg
Gas Pipe Cutter
PIPEMATE Gas Pipe CutterAccurate square & bevel edge•
circumferential flame cutting.Designed for optimum stability.•
Designed for simple Operation.•
Fully adjustable to any cutting•
angle.Quick changeover between•
differing pipe diameter.
The Strong lightweight PIPEMATE, portbility with high cutting accuracy.
The PIPEMATE pipe cutter is one of the CIGWELD range of quality fiame cutting machine only 9kg.This hardworking unit offers troublefree maintenance, easy operation and true portability. With itsdependable chain drive, the PIPEMATE solves most circumferential cutting problems, independentof electrical supply. This machine is easily moved from job to job and is at much at home on site asin the workshop. The PIPEMATE is capable of producing square cuts and bevel edge preparationsover a wide range of pipe diameters and wall thickness.
Construction Features
Among the many advantages to this rigidly constructed machine are:Smooth, Dependable Drive
.levarthtoomsylemertxenistluseroitarraegwoleht,leehwmrowdnamrowahguorhtsievirDThe drive gear and gear chain are designed for maximum stability, thus reducing backlash ineither direction.Simplified Operational ControlThe Control valves for fuel gas, heating oxygen and cutting oxygen are located away from the heataffected zone, conveniently placed foe easy operator use,Adjustable BlowpipeUsing either CIGWELD acetylene or LPG 3 seat cutting nozzles, the cutting blowpipe may beadjusted 80mm perpendicular to the pipe surface and 120mm along the pipe surface by rackand pinion . A graduated scale ensures accurate bevel setting, and a wing nut locks the cuttingblowpipe firmly in position.
AS00136
Lightweight Portable Flame Cutting Machine
AS00139
Designed to enhance workshopefficiency, the PLATEMATE 2 iscompact and light without loss ofaccuracy or cutting capacity.
Automatically cuts straight lines,•
circles and bevelsLightweight•
Portable•
Compact construction•
Designed for simple operation•
High stability for long distance•
cutting
3 SEAT CUTTING NOZZLES
Standard Speed Acetylene
Part No. Tip Size Plate Thickness (mm)
306114 00 0 to 5
306115 0 5 to 10
306116 1 10 to 15
306117 2 15 to 30
306118 3 30 to 40
306119 4 40 to 50
Standard Speed LPG
Part No. Tip Size Plate Thickness (mm)
306096 00 0 to 5
306097 0 5 to 10
306098 1 10 to 15
306099 2 15 to 30
306100 3 30 to 40
306101 4 40 to 50
SEAT CUTTING NOZZLES
Standard Speed Acetylene
Part No. Tip Size Plate Thickness (mm)
5ot000411603
01ot50511603
51ot01161160303ot512711603
04ot033811603
05ot044911603
Standard Speed Acetylene
Part No. Tip Size Plate Thickness (mm)
5ot000690603
01ot50790603
51ot011890603
03ot512990603
04ot033001603
05ot044101603
Specifications
Machine Part No. 338534
Pipe Diameter 100–600mm with standard chain
Pipe Wall Thickness up to 50mm
Optional Accessories
Additional 2m chain P.N. 333094
Included Accessories
Cutting Tip Acetylene Size 1 1 Pc
cP1srenaelCpiT:slooT
Spanners 3 Pc
Chain Link VersatilityThe drive chain consists of interlocking links that are easily added or removed for rapid chargesbetween pipes of different diameters.
Specifications
Machine Part No. 338536
Weight (one torch set) 9.5kg
mm053htgneL
Wheel width 160mm
Motor
Reduction gear
Model:Power Source:
Revolution:
Condenser-induction240V50Hz1500rpm(no load)Single cone system
Cutting Speed 150–800mm/min
Cutting Thickness 5–50mm
Cutting edge shape Square cutting
V–Bevel Cutting
Rail 1.8m Log P.N.335287
Two Touch Set P.N.338538
Circle Cutting Attachment P.N.338539
Plant Includes
1 x PLATEMATE 2
1 x Cutting Torch
1 x Cutting Tip Acetylene Size 1
1 x Tip Cleaners
1 x Spanners
Pipe Mate – AS00136
Plate Mate – AS00139
Specifications
Welding Products
7/23/2019 Welding Products(Pg164-180) (1)
http://slidepdf.com/reader/full/welding-productspg164-180-1 10/17173
Allinton Engineering & Trading Pte Ltd Head Ofce: 331 Jalan Besar, Singapore 208983. 6296 0679 (10 lines) 6297 0024
Branch Ofce: 21 Tuas Basin Link Singapore 638782 6265 1888 (10 lines) 6265 5623www.allinton.com.sg allinton@singnet.com.sg sales@allinton.com.sg
Cutting TorchCode No. Model
AS00140 Type 250
Welding TorchCode No. Model
AS00145 Weld Master
Welding TorchCode No. Model
AS00146 Weld Master
Tig TorchCode No. Size
AS00148 150AMP
Tig TorchCode No. Size
AS00149 200AMP
Heating TorchCode No. Model
AS00150 Weld Master
Gouging TorchCode No. Size
AS00171 400AMP
Sanritsu #8575 Electrode Holder
AS00168
Electrode HolderCode No.
AS00168
AMP
500
Code No. AMP
Gouging TorchCode No. Size
AS00172 600AMP
Welding and Cutting Set Welding and Cutting Torch
Cutting TorchCode No. Model
AS00371 Type 200
Type 23AS00152
AS00149
AS00146
AS00371
AS00148
AS00171
AS00170
AS00172
AS00145
AS00140
Heating TorchType 02AS00150
Type 21AS00153
AS00170 500AS00169 300
Welding Products
7/23/2019 Welding Products(Pg164-180) (1)
http://slidepdf.com/reader/full/welding-productspg164-180-1 11/1774
Allinton Engineering & Trading Pte Ltd Head Ofce: 331 Jalan Besar, Singapore 208983. 6296 0679 (10 lines) 6297 0024
Branch Ofce: 21 Tuas Basin Link Singapore 638782 6265 1888 (10 lines) 6265 5623www.allinton.com.sg allinton@singnet.com.sg sales@allinton.com.sg
Oxygen RegulatorCode No. Model
AS00155 Oxygen
Oxygen & Actylene FlashBack Arrestor for Regulator
Code No. Model
AS00184AS00188
OxygenAcetylene
Oxygen & Actylene FlashBack Arrestor for Torch
Code No. Model
AS00175AS00179
OxygenAcetylene
Actylene RegulatorCode No. Model
AS00159 Acetylene
Argon Regulator R-11
High Pressure:250kgs/cm²Low Pressure:25 litres/min
Argon FlowMeter
Nitrogen Regulator
Oxygen & Acetylene FlashbackBack Arrestor for Hose
Code No. Model
AS00372AS00373
OxygenAcetylene
British Type HoseCheck Valve
Code No. Size
AS00391AS00392
3/8”BSP x 6mm RH3/8”BSP x 6mm LH
USA Type HoseCheck Valve
Code No. Size
AS00393AS00394
9/16” x 6mm RH9/16” x 6mm LH
Nut & Hose NippleCode No. Size
AS00387AS00388
3/8”BSP x 6mm RH3/8”BSP x 6mm LH
Hose CouplersCode No. Size
AS00389AS00390
AS00395AS00396
AS00397AS00398
9/16” x 9/16” RH9/16” x 9/16” LH
5/8”—19T x 9/16”—18T9/16”—18T x 5/8”—18T
3/4”—14T x 3/4”—14T LH3/4”—14T x 3/4”—14T RH
Carbon Dioxide Regulator
Propane Flash Back Arrestor
Inlet Connection:22mm Ø x 14th.RHExhaust Pressure:Standard 2kgs/cm
AS00155 AS00159
36100SA26100SA
AS00166
AS00179
AS00184
AS00188
AS00372 AS00373
AS00181
AS00389
AS00387AS00391 AS00393
AS00394
AS00397
AS00395
AS00175
AS00164
Welding Products
7/23/2019 Welding Products(Pg164-180) (1)
http://slidepdf.com/reader/full/welding-productspg164-180-1 12/17175
Allinton Engineering & Trading Pte Ltd Head Ofce: 331 Jalan Besar, Singapore 208983. 6296 0679 (10 lines) 6297 0024
Branch Ofce: 21 Tuas Basin Link Singapore 638782 6265 1888 (10 lines) 6265 5623www.allinton.com.sg allinton@singnet.com.sg sales@allinton.com.sg
Welder FixerCode No. Size
AS00400
AS00401
AS00588
AS00589
3”
4”
5”
6”
Oxygen
AS00208
Earth Clamp
AS00190
G Type Ground Clamp
AS00193
ANME Cutting NozzleCode No. Size
AS00194
AS00195
AS00196
AS00197
AS00198
AS00199
AS00200
1/32”
3/64”
1/16”
5/64”
3/32”
7/64”
1/8”
AS00194
PNME Cutting NozzleCode No. Size
AS00201
AS00202
AS00203
AS00204
AS00205
AS00206
AS00207
1/32”
3/64”
1/16”
5/64”
3/32”
7/64”
1/8”
AS00201
Twin Outlet Valve
Acetylene
AS00209
Cable Connector Pin TypeCode No. Size
AS00210
AS00211
300AMP
500AMP AS00210
Cable Connector Screw TypeCode No. Size
AS00212
AS00213
300AMP
500AMP AS00212
Head Shield
AS00217
Hand Shield
AS00218
Welding Goggle
AS00219
Welding Spectacle
AS00220
Rock Spark Gun
AS00222AS00221
Flint Stone
3 Flint Spark Lighter
AS00224AS00223
Flint Stone
Oxygen Key
AS00225
Code No. Size
AS00190AS00191
AS00192
300AMP400AMP
500AMP
Welding Mask withSafety Cap
AS00350
American Cable Joint 500AMP
AS00351
Welding Products
7/23/2019 Welding Products(Pg164-180) (1)
http://slidepdf.com/reader/full/welding-productspg164-180-1 13/1776
Allinton Engineering & Trading Pte Ltd Head Ofce: 331 Jalan Besar, Singapore 208983. 6296 0679 (10 lines) 6297 0024
Branch Ofce: 21 Tuas Basin Link Singapore 638782 6265 1888 (10 lines) 6265 5623www.allinton.com.sg allinton@singnet.com.sg sales@allinton.com.sg
Dark Glass
2” x 4”AS00228
AS00342AS00343AS00344
No 10
No 11No 12No 13
Fibreglass Tape
Size 2” x 3mm x 30mAS00374
AN00609
Fibreglass Cloth
Model No.Code No.Density
TemperatureResistance CapabilityWeave TypeColour FinishThicknessWidthRoll Length
TX3000AS002501600g/m²550°C(Max Continuously)PlainWhiteTexturised3.0mm1.0m15m
Fibreglass Cloth
Model No.Code No.
DensityTemperatureResistance Capability
Weave TypeColour FinishThicknessWidth
Roll Length
HT800AS002481650g/m²550°C(MaxContinuously)SatinGolden BrownHeat Treated1.0mm1.0m
50m
G1700AS002491100g/m²550°C(MaxContinuously)PlainGolden BrownTexturised1.7mm1.0m
30m
Clear Glass
2” x 4” AS00229
AS00247
Tempilstiks
Tempilstiks are made of materials with melting points calibrated to a guaranteed tolerance of±1%. There are a total of 103 temperature ratings with melting points systematically spacedbetween 100ºF/38ºC and 2500ºF/1371ºC. Most can be certified to be lead and sulfur free.Every Tempilstik is traceable by lot number to the specific batch of raw material from whichit was made.
Tempilstik, Tempilaq and Tempil Pellets are available in the following temperatures:
°F °C °F °C °F °C °F °C °F °C °F °C
100103106109113119125131138144
150156163169175182188194200
38394143454852555962
666973767983879093
206213219225231238244250256263
269275282288294300306313319
97101104107111114118121124128
132135139142146149152156159
325331338344350363375388400413
425438450463475488500525550
163166170173177184191198204212
218226232239246253260274288
575600625
•650
700•750
•800
•850
900932
950977
10001022
•105011001150
•1200•1250
302316329343371399427454482500
510525538550566593621649677
•1300•1350•1400
1425•1450
1480•1500
155016001650
1700•1750
18001850
•19001950200020502100
704732760774788804816843871899
927954982101010381066109311211149
•2150•2200
•2250
•2300
•2350
24002450
•2500
11771204123212601288131613431371
°Series “R” tempil Pellets available in these temperatures, 550ºF and below. Regular Pellets can be used forreducing atmospherre. Aerosol Tempilaq not available below 150ºF/66ºC.
Cable Lux
Fire Blanket
Code No. Size
AS00214AS00215AS00216
300AMP400AMP500AMP
Code No. Size(m)
AN00609
AS00214
Nozzle Cleaner
AS00227AS00226
Nozzle Cleaner (Box Type)
1.8m x 1.2m
Welding Products
7/23/2019 Welding Products(Pg164-180) (1)
http://slidepdf.com/reader/full/welding-productspg164-180-1 14/17177
Allinton Engineering & Trading Pte Ltd Head Ofce: 331 Jalan Besar, Singapore 208983. 6296 0679 (10 lines) 6297 0024
Branch Ofce: 21 Tuas Basin Link Singapore 638782 6265 1888 (10 lines) 6265 5623www.allinton.com.sg allinton@singnet.com.sg sales@allinton.com.sg
AS00265
AS00266
AS00267
Pipe Cutting & Beveling Machines
Short Saddle Machines• Fast Set Up• AccurateMathey Dearman Short Saddle Pipe Cutting and Beveling Machines provides fast,clean, and accurate cuts in preperation for fitting pipe. The single piece saddlerequires less maintenance. Precision machined to provide close tolerance control ofmovements. Using a Mathey Dearman machines, you will not waste time or material.These machines have the capability to be installed either perpendicular or parallel tothe pipe. They are available in either manual or motorized form. Uses oxy -acetyleneor plasma torch. Motorized machine is recommended if a plasma torch is being used.
AS00268
Electrode OvenModels K-50
SpecificationsElectrode Capacity
Volts (Specify)WattsThermostatTemperatureInsulationInterior Dimensions
Net WeightShipping WeightShipping Dimensions
•Part-#010201 - (120V)•Part #010202 - (240V)
50 Lbs. (22.7 kg) 18” (45.7cm)
120V / 240V AC/DC150W / 150WFactory preset/Field adjusrablePreset 275˚F (135˚C) Range100˚-300˚F (50˚-150˚C)1” (2.54cm) T.I.W.6” (15.24 cm) x 18.5”(46.99cm) x 6” (15.24 cm) x 19” (48.26 cm)18 Lbs. (8.16kg)21 Lbs. (9.53kg)10.5” (26.67cm) x 9” (22.86cm) x 22.75” (57.78cm)
Electrode OvenHolding OvensModels K-200
SpecificationsElectrode CapacityVolts (Specify)WattsThermostatTemperature
InsulationInterior DimensionsNet WeightShipping WeightShipping Dimensions
•Part-#010301 - (120V)•Part #010303 - (240V)
200Ibs. (90.7kg) 18” (45.7 cm) rods120V / 240V500w / 500wFactory preset / Field adjustablePreset 275˚F (135˚C)Range 100˚-300˚F (50˚-150˚C)1” (2.54cm) Thermal Insulating Wool12.5” (31.75cm) x 12.5” (31.75cm) x 18.25” (46.35cm)53Ibs. (24.04kg)66Ibs. (29.94kg)19.5” (49.53cm) x 17.5” (44.45cm) x 27” (68.58cm)
Electrode OvenModel K-15 W/TSpecificationsElectrode CapacityVolts (Specify)WattsThermostatTemperatureInsulationInterior DimensionsNet Weight
Shipping WeightShipping Dimensions
•Part #010102-(120V) •Part #010103-(240V)
15 Ibs. (6.8kg) 18” (45.7cm) rods120V / 240V AC/DC150W / 150WFactory pretset /Field AdjustablePreset 275˚F (135˚C) Range 100˚-300˚F (50˚-150˚C)1” (2.45cm) Thermal Insulating Wool3.3”D (8.38CM) x 19”H (48.26cm)13Ibs. (5.9kg)
16Ibs. (7.3kg)10.5” (26.67cm) x 9” (22.86cm) x 22.75” (57.78cm)
Electrode OvenModels K-450
Specifications
Electrode CapacityVolts (Specify)WattsThermostatTemperature
InsulationInterior DimensionsNet WeightShipping WeightShipping Dimensions
•Part #010402 - (120V)•Part #010401 - (240V)
450Ibs. (204.1kg) 18” (45.74cm) rods120V / 240V1000W / 1000WDial adjustable120V: 150˚-550˚F (50˚-350˚C)240V:150˚-550˚F (50˚-350˚C)2” (5.08cm) Thermal Insulating Wool19.5” (49.53cm) D x 20” (50.80cm)73Ibs. (33.11kg)90Ibs. (40.82kg)26” (66.04cm) x 28” (71.12cm) x 26” (66.04cm)
Stack Kit available for stacking K-450 ovens two high.* K-450 480V single-pharse available.
AS00264
AS00261
AS00259
AS00256
Portable Electrode Dryer
Electrodes Dryer – Magnet Type
Electrodes Dryer – Wire Type
Electrodes Dryer –Temperature Control Type
Code No. Rod Length(mm)
Rod Weight(kg)
Capacity(W)
Ø x Over all Height (mm)
Weight(kg)
Remarks
AS00259 550 5 600/80 230Ø x 735H 7 Level-raising base
AS00260 750 10 800/80 230Ø x 835H 11 Inclined, with 50mmlevel-raising
Code No. Rod Length(mm)
Rod Weight(kg)
Capacity(W)
Ø x Over all Height (mm)
Weight(kg)
Remarks
AS00255 450 5 200 180Ø x 600H 3 Upright
AS00257 750 10 300 180Ø x850H 7 Inclined
Code No. Rod Length(mm)
Rod Weight(kg)
Capacity(W)
Ø x Over all Height (mm)
Weight(kg)
Remarks
AS00256 450 5 200 180Ø x 600H 3 Upright
AS00258 750 10 300 180Ø x850H 7 Inclined
AS00255
Welding Products
7/23/2019 Welding Products(Pg164-180) (1)
http://slidepdf.com/reader/full/welding-productspg164-180-1 15/1778
Allinton Engineering & Trading Pte Ltd Head Ofce: 331 Jalan Besar, Singapore 208983. 6296 0679 (10 lines) 6297 0024
Branch Ofce: 21 Tuas Basin Link Singapore 638782 6265 1888 (10 lines) 6265 5623www.allinton.com.sg allinton@singnet.com.sg sales@allinton.com.sg
VESI - MAG - HOLDER
VERSI–MAG–HOLDER This tool replaces the VERSI–MAG–TOOL, Stock No. 21. New tool willcarry Stock No. 21-A. Desirable for holding welding lead or hose lengths suspended in air forstructual type work. Holds all types weldingtorches. Squared on each end and hinged to swing
90 degree angle to art as jig or line-up for small parts, welding or machinist work. Two 25lb.Pull–magnets, cast-in aluminum body with machined V-base, hinged together with pin for flat oroval surface.
AS00292
Contour Markers™
For Making off Pipe Joints and Structural Angle Cuts
No. mistakes – no loss of time – regardless of the typeor size of pipe joint to be welded – that’s just oneadvantage of the CONTOUR MARKER.™Standard for 1/2” to 18” pipe and structuralsModel including strucural adaptor …Stock No. #101
Pro–Mag–Level
This level is designed for the fitter, welder, jig builder, for any layman who has angle or settingproblems. the Pro-Mag-level is 9” in length, 2” high, 3/4” wide, weighing a total of 10oz.- aconvenient pocker size. Body of level is made of strong aluminum casting to maintain lightness oftool. (scales are imprinted on front of the tool for rise in degree per foot and degrees in rise permeter. Equipped with level and 90 degrees dial marker in 21 /2 degrees, held in place by screwwith pressure washer for easy setting. Frame of level is equipped with two magnets for holding alevel in desired position, allowing the layman a third hand. Above illustration shows tool in opera-tion in two positions.
No more “cut and try” – it eliminates the need forcalculation, and is available in two sizes for markingpipe and structurals of 11/2” to 18” in cross section,and from 8” to 48” diameter. Jombo for 8” to 48” pipe and structurals includingModel strucural adaptor ………….. Stock No. #104
AS00293
AS00294
AS00295
Wrap-A-Round
An inexpensive WRAP–A–ROUND for making straight lines around pipe or for use as a straightedge. Make out of flexible gasket material, reasonable resistant to heat and cold.
Ex-Small
SmallMediumLargeEx-LargeEx-Large
Width 1.94”xLength 2’
Width 2.5”xLength 2’Width 3.88”xLength 4’Width 3.88”xLength 6’Width 5”xLength 7’Width 5”xLength 9’
1” to 3” pipe
1” to 3” pipe3” to 6” pipe3” to 10” pipe4” to 12” pipe6” to 16” pipe2” to 30 ” pipe12” to 48” pipe
….Stock No.150B
….Stock No.126….Stock No.164B....Stock No.176B....Stock No.177B....Stock No.179B
AS00283
AS00284AS00285AS00286AS00287AS00288
Special sizes available on order, 3.88”, 5” & 7” width to any length to 375’. All Wrap-A-Roundare available in three colours to designate material type and service temperatures.G (Gray) Regular asbestos type material, up to 250 F.B (Black) Asbestos-free material, use to 325 F.W (White) Asbestors-free material (high Temp) above 350 F.
AS00283
Stock No. #108
Stock No. #107
Fitter Weld Protractor
A 90˚ protractor with matchinglocking lever to set and holdprotractor at desired angle,mounted in a 3/4” width framewith a 3/8” by 6” cast–in rod.Equipped with 5/8” by 10” armto complete finding of angles ordesired bends. Also to determineany portion of elbows or 90˚. This new tool comes with a 25# pullmagnetic base for holding protractor frame in position. Tool can be usedmanually or with magnetic base, as illustration above shows.
Centering Head
Determines Center Line at any Degree and Measures Degree of Declivity
With Dial–Set–Level and 8” Y-Type Headwith Spring Loaded Hardened Punch.
Works 1” pipe and up to large tanks.• Establish Angles and Mark for Butt-Ins• Locate Points Inside Pipe or Tanks• Set Tanks• Lay Out Keyways • Measure Declivity
Jumbo
With Dial–Set–Leveland 4” Y-Type Head
with manual operatedhardened punch.Works 1 /2” pipeand up.
Stock No. #106
Stock No. #9Standard
79200SA69200SA
AS00298
SpecialSpecial
Width 5”xLength desiredWidth 7”xLength desired
....Stock No.128..Stock No.132
AS00290
AS00291
Welding Products
7/23/2019 Welding Products(Pg164-180) (1)
http://slidepdf.com/reader/full/welding-productspg164-180-1 16/17179
Allinton Engineering & Trading Pte Ltd Head Ofce: 331 Jalan Besar, Singapore 208983. 6296 0679 (10 lines) 6297 0024
Branch Ofce: 21 Tuas Basin Link Singapore 638782 6265 1888 (10 lines) 6265 5623www.allinton.com.sg allinton@singnet.com.sg sales@allinton.com.sg
Univer Level
Flange orientation and pipe leveling ang aligning are amongthe many capabilities of the UNIVERSAL LEVEL. TheCURV-O-MARK® UNIVERSAL LEVEL, the leveling tool thatpipefitters and pipe weldors have been waiting years to get theirhands on - is here! In one tool, a level, there is available all thefunctions of a leveling device, such as, the capability of levelinga run of pipe but also the capacity for accurately setting apredetermined pitch of a string of pipe, setting the angle of
dnasnurlacitrevgnieurt,eergedesicerpaotslaretal“two-holing” flanges. All because the UNIVERSAL LEVEL is flttedwith a CURV-O-MARK® protractor dial bubble. The CURV-O-MARK® UNIVERSAL LEVEL is adurable aluminum casting to make it light-weight and rust proof. There are two cast-in 25-pound-pull
magnets (exerting a 50-pound-pull) which securely hold the level in place on any steel surface; afeature that makes for “handsfree” leveling – a welcome aid in some ‘tight” spots.
Combination Adaptor AccessoryFor Contour Marker™ Jombo or Standard models
This new tool paten will prove a great advantage to the layman, allowing him to use all four sides of the CONTOURMARKER™ in lay-outs on pipe, also structural steel. It allows him to work up to 30” pipe with the Standard Modelor up to 100” pipe with the Jombo Model by quartering or halfing his pipe. With i t he can mark over nipples,oldwelds, and without having to break the wrap so far back on wrapped pipe. The ADAPTOR allows him towork compound angles in one setting of the tool, also to mark off any portion of elbows or 90 degrees he wouldso desire, as you will note self explanatory illustration above. The tool is sold by your welding distributor as anaccessory to the CONTOUR MARKER™
Standard Combination Adaptor…………........Stock No. 105 AS00299 Jumbo Combination Adaptor…………........….Stock No. 106 AS00300
00300SA99200SA
Radius Markers
THE STANDARD RADIUS MARKER folds to packet size. This sturdy, folding Radius Marker has a span of 8” for 1208, 20” for 1220, 24” for 1224and easily swings a 16”, 40”, 48” circle or arc. THE JUMBO RADIUS MARKER is also the folding type; has a span of 40” and easily swing a 80”circle. These tools are precision made of rust proof aluminum dural. The Standard Radius Marker 1224 folded, measures only 91 /4” in length, weighingonly 8 oz. The jumbo Model of course, is larger. Both are equipped with special spring washers to maintain accuracy and rigidity for years of service.Pencil holder is made to hold round or flat pencils, soapstone, or steel point.MINI………………….......……….......…....Stock No. #118 AS00301
SMALL…………….......….......………....….Stock No. #119 AS00302 AS00301
STANDARD………………..............…....….Stock No. #120 AS00303
JUMBO…………………......... .........………Stock No. #114 AS00304
Circle Ellipse Projector
This tool is designed for making perfect circles, ellipse or oblong circles. The tool will work on pipe, tanks, boilers, cones, or any irregular, flat or roundsurface. It is designed with strong magnettic base to hold in position while desired work is being performed. It also has sliding rods with protractor andlocking lever to adjust for desired lay-out, and a designed chalk holder for round or flat soapstone or will receive steel scribe or pencil. This tool worksfrom 11 /2” circles to 18” circle. Also can be adjusted from (0) to 90 degree angle. Attachment for use on large pipe available on request.Stock No. #115.. AS00305
AS00305
AS00306
Multi-Trammel Head
MULTI-TRAMMEL HEADS are diecast of strong durable, aluminum and are machine to accept standard 1 /2” pipe or bar. Weight approximately 8 oz.per set. equipped with 1 /4” thumb screws and squared on back side for perfect perpendicular aligment. One head holds 1/4” case hardened centerpoint. The movable head holds 1 /8” steel scribe, hardened to 59 rockwell. Also, the chalk holder will accept any of the marking devices illustrated inpicture. Radius setting points are cast in alighment with marking pionters for easy setting. Marks from 11 /2” circle to as large a diameter as desired,depending on length of 1 /2” pipe used for t rammel bar.Stock No. #117.. AS00306
Pipe Flange Aligners
Easily inserts itself into pipe•
Centers itself snugly against in side pipe diameter•
Automatically aligns with pipe axis.•
Faster, more accurate pipe line construction is now made easy with thisself-determining Flange Aligning Tool. Itis quickly adjustable for all typesof flanges or pipe sizes ranging from 3” to 12” in diameter.
AS00307
STANDARD MODEL……………………………Stock No. #10 AS00307
Dial Angle Flange Level
This new tool is a casting equipped with theCURV-O-MARK® protractor with level and two pinsheld to body of level on a sliding scale. The slidingscale on body allows the use of this tools on any sizeflange as you always will use the two holes closesttogether and then revolve flange to zero on any angleto which you set dial. The two threaded, self-aligningconical spacer and conical nut and bolt units aredesigned to fit any size bolt hole. This method iscommonly Known as two-holing a flange only in amore unique manner. The body of this tool is 1 /2” thick with a machined surface, therefore, allowingthe removal of pins from body and using as a regular dial degree utility level.
Stock No. #109AS00310
Stock No. #111AS00312
Welding Products
7/23/2019 Welding Products(Pg164-180) (1)
http://slidepdf.com/reader/full/welding-productspg164-180-1 17/17
Allinton Engineering & Trading Pte Ltd
Inspection Mirrors and Pick–up Tools
UG–B06 Flexible Mirror with Light Tool
Type Dia. Length V/O Battery Packing
Oval 25 x 50mm 500mm DC 2 AA’s 1.5 Volts Sliding on card12/72pcs/2.5cuft/17.0kgs
UG–B151 Telescoping Inspection Mirror Tool
gnikcaPhtgneL.aiDepyT
Round 55mm 250 to 780mm Sliding on card25/100pcs/2.2cuft/19.0kgs
UG–B136 Telescoping Inspection Mirror Tool
gnikcaPhtgneL.aiDepyT
Round 38mm 115 to 510mm Sliding on card25/200pcs/1.6cuft/11.0kgs
UG–B152 Telescoping Inspection Mirror Tool
gnikcaPhtgneL.aiDepyT
Rectangle 50x90mm 260x810mm Sliding on card25/100pcs/2.2cuft/19.0kgs
UG–B22 Flexible Magnet Pick–up Tool
Length Pick–up Description Packing
560mm 3.5lbs PVC handle green plated,Chrone plated shank
Card25/100pcs/1.8cuft/18.0kgs
UG–B08 Telescoping Magnet Pick–up Tool
Length Pick–up Description Packing
305 to610mm
1.0lbs Ball joint allows head to swivel,Black PVC coated housing
Sliding on card24/144pcs/2.2cuft/25.0kgs
UG–B15 Magnetic Pick–up Tool Heavy Duty PocketgnikcaPhtgneLpu–kciP
3.5lbs 130 x 640mm Blister on card50/200pcs/1.0cuft/10.0kgs
UG–B455, UG–B455A & UG–B355 3 in 1 Lighted Magnetic Mirror
gnikcaPhtgneLpu–kciP
3.5lbs 130 x 640mm Blister on card50/200pcs/1.0cuft/10.0kgs
UG–B137B 2 in 1 Magnetic & Mirror
htgneL.aiDyticapaCepyT
Round 1.1lbs 32mm 250 x 500mm
UG–B2100 2 in 1 Lighted Maguetic Pick-up Tool
Capacity Description1.5lbs Telescoping handle pocket
41300SA31300SA
61300SA51300SA
81300SA71300SA
02300SA91300SA
AS00321 AS00322
Welding Products
Recommended