View
224
Download
0
Category
Preview:
Citation preview
Towards a Lighter Engine for Improved Aircraft Fuel Efficiency – Industrial Collaborative Research on Engine Weight Reduction Technologies
Presented By: Dr. Hamza M. Abo El Ella May 19, 2016
National Research Council
• The National Research Council (NRC) is the primary national research and technology organization (RTO) of the Government of Canada. • A federal government agency for science and technology research.
2
National Research Council
3
National Research Council
4
• Aerospace • Gas Turbine Lab (GTL) • Flight Research Lab (FRL). • Aerodynamics Lab (AL). • Structures, Materials, and Manufacturing Lab (SMM).
Introduction: Gas Turbines for Aircraft Propulsion
5
Typical mid-bypass turbofan engine (Pratt & Whitney PW6000)
Fan
Inter-Compressor Duct
Inter-Turbine Duct
LP Turbine
LP Compressor
HP Compressor
Exhaust Mixer
HP Turbine
Introduction: Improving Aircraft Fuel Efficiency
• Improve engine fuel efficiency. • Reduce pressure losses.
• E.g. optimize cavity flows.
6
Rotor
Purge flow
Rotor disc
Stator
Cavity at rotor-stator interface
(Abo el ella, 2014)
Introduction: Improving Aircraft Fuel Efficiency
• Reduce engine weight. • Highly-loaded airfoils (reduces blade count but increases secondary
losses – critical for low AR, i.e. HPT).
7
ou da y aye u d
Suct o s de eg o o ses oe o teessu e s de eg o
o ses oe o te
Passage vortex
Countervortex
Corner vortex
Boundary layer fluid
Inlet flow Freestream
fluid
Direction of rotation
Suction side leg of horseshoe vortexPressure side leg of
horseshoe vortex
Secondary flows Secondary flows
Introduction: Improving Aircraft Fuel Efficiency
• Reduce engine weight. • Highly-loaded airfoils (reduces blade count but increases secondary
losses – critical for low AR, i.e. HPT). • Must lower secondary losses (endwall contouring).
8
(Praisner et al)
Introduction: Improving Aircraft Fuel Efficiency
• Reduce engine weight. • Highly-loaded airfoils (reduces blade count but increases secondary
losses – critical for low AR, i.e. HPT). • Must lower secondary losses (endwall contouring).
• Reduce size or length of ducting and other components. • Inter-compressor duct (ICD). • Inter-turbine duct (ITD). • Exhaust mixer.
9
10
Typical mid-bypass turbofan engine (Pratt & Whitney PW6000)
Fan
Inter-Compressor Duct
Inter-Turbine Duct
LP Turbine
LP Compressor
HP Compressor
Exhaust Mixer
HP Turbine
Inter-Turbine Duct (ITD)
Inter-Turbine Ducts: Objectives
11
• Extend the ITD design envelope to achieve: • Minimum length or • Maximum radial offset • with minimal or no
performance penalty.
• Benefits • Reduced engine length. • Reduced fan/LPT RPM. • Reduced LPT stage count. • Reduced engine weight.
Inter-Turbine Ducts: Initial Approach
12
• Computational and Experimental Studies on S-shaped ducts. • CFD. • ITD Rig.
• Duct test section. • Upstream swirlers to simulate HPT.
Inter-Turbine Ducts: Initial Approach
13
• Three S-shaped aggressive duct geometries (ITD-B, ITD-C, and ITD-D) where designed and tested with a common swirler geometry, and compared to a baseline duct (ITD-A).
ITD-B ITD-C ITD-D
(Mahallati et al, 2013 - GT2013-95065)
Inter-Turbine Ducts: Some Results
14
• CFD and experimental results (ITD-B). • Detailed flow information for improved understanding of the
underlying flow physics and loss mechanisms for simple ducts.
(Mahallati et al, 2013 - GT2013-95065)
Inter-Turbine Ducts: Later Approach
15
• Subsonic Turbine Rig • Single stage turbine.
• Duct test sections.
Inter-Turbine Ducts: Some Results
16
• ITD-D was examined in the subsonic turbine rig to confirm the positive influence of tip leakage vortices in suppressing shroud flow separation.
Inter-Turbine Ducts: Current Approach
17
• Numerical approach using engine representative geometry (with experimental validation in subsonic turbine rig). • Struts used for structural support and housing oil supply lines.
• Can be used aerodynamically to enable aggressive designs.
(Mahallati et al)
18
Inter-Turbine Ducts: Future Work
• Experimental validation in the subsonic turbine rig. • Experimental validation at high speeds. • Optimizer tools for generating aggressive ITD geometries. • Active flow control strategies.
Exhaust Mixer
19
Typical mid-bypass turbofan engine (Pratt & Whitney PW6000)
Fan
Inter-Compressor Duct
Inter-Turbine Duct
LP Turbine
LP Compressor
HP Compressor
Exhaust Mixer
HP Turbine
Exhaust Mixer: Objectives
20
• Gain better understanding of flow physics. • Gases mix downstream of the
forced mixer before exiting the nozzle to improve thrust and reduce noise. • Some exhaust systems use
tabs to provide stiffness.
(Wright et al, 2015 - ISABE-2015-20246)
Exhaust Mixer: Approach
• CFD - Unstructured mesh. • Grid independence study
showed 5.5M cells were sufficient.
• Grid is fine enough to resolve wall boundary layers, free shear layers, mixing zones.
21
(Wright et al, 2015 - ISABE-2015-20246)
Exhaust Mixer: Some Results
22
Streamwise vorticity coefficient (No Tabs) Streamwise vorticity coefficient (With Tabs)
Downstream axial planes at x/Dh=0.07, 0.36, 0.72, 1.45 and 2.90
(Wright et al, 2015 - ISABE-2015-20246)
Total pressure coefficient (No Tabs) Total pressure coefficient (With Tabs)
Exhaust Mixer: Some Results
23
Downstream axial planes at x/Dh=0.07, 0.36, 0.72, 1.45 and 2.90
(Wright et al, 2015 - ISABE-2015-20246)
Exhaust Mixer: Other Work
24
• Weight reduction – e.g. exhaust casing struts and mixer integration.
• Effect of scalloping on mixer performance. • Effect of inlet swirl.
Exhaust Mixer: Future Work
25
• Experimental validation of flow physics. • Active cooling of exhaust mixer for improved durability.
Summary
26
• Engine weight reduction for improved aircraft fuel burn • Inter-Turbine Duct. • Exhaust Mixer.
• Collaborating with industry is a must to ensure valid practical solutions.
• N+0.1: 1-2% aircraft fuel burn improvement.
Acknowledgments
27
• Ali Mahallati • Alex Wright
Hamza.aboelella@nrc.ca
Recommended