View
10
Download
0
Category
Preview:
Citation preview
Honda Dealer: Please give a copy of these instructions to your customer.
Issue Date
March 2016
INSTALLATIONINSTRUCTIONS
Accessory Application Publication No.
MII 15736
© 2016 American Honda Motor Co., Inc. - All Rights Reserved.
PARTS LIST
08E70-MKA-D801 of 5
ACCESSORY SOCKETP/N 08E70-MKA-D80
After '15NC700X/XD, NC750X/XD
No. Description Qty
(1) Installation Instruction URL 1
(2) Socket assy. 1
(3) Wire tie (wide) 1
(4) Accessory harness 1
(5) Safety information label 1
(6) Wire tie (narrow) 1
(1)
No. Description Qty
(1) Subharness 1
(2) Wire tie 1
SUBHARNESSSold separately
SOCKET HARNESS
SOCKET RING
ACCESSORY SOCKET
(2)
(4)
(6)
(3)
(5)
(1)
(2)
No. Description Qty
(1) Fuse (7.5 A) 1
(2) Relay 1
(1)(2)
RELAY SETSold separately
TOOLS AND SUPPLIES REQUIREDSide cutters
Electric drill
Hole saw (30 mm)
Awl
Electrical tape
Isopropyl alcohol
Shop towel
TORQUE INFORMATIONRefer to the Service Manual for the torque values of the removed parts.
2 of 5
PREPARING THE RELAY SET• These procedures are not required for a
motorcycle already equipped with the Relay Set.• Illustration shows NC700X type, other types are
similar.
2. Install the relay and fuse in the position shown.
1. Refer to the Service Manual for the motorcycle, remove the motorcycle parts, and disconnect the negative (-) cable from the battery as shown.
FUSE
RELAY
MAINTENANCE LIDSCREW
BOLT
NEGATIVE (-) CABLE
FUSE BOX COVER
RELAY
FUSE
INSTALLATION INFORMATION CAUTION
• To prevent burns, allow the engine, exhaust system, radiator, etc., to cool before installing the accessory.
NOTE:
• Take care not to damage the painted surfaces of the motorcycle.
• Disconnect the negative (-) cable from the battery before installing this accessory.
• The memory of the clock will be erased when you disconnect the battery. After reconnecting the battery, refer to the motorcycle Owner’s manual and reset the clock.
• Trim the excess ends off the wire ties after attaching them to the wire harness. Do not allow the cut part of the wire tie interfere with any harness or brake hose.
• After this accessory installation, check the lights (e.g. right/left turn signal lights and brake lights) for proper operation.
• Heat the bonding surfaces with a hair dryer if the ambient air temperature is below 70°F (21°C).
• The adhesive reaches full strength in 72 hours. Wait at least 24 hours before riding your motorcycle.
• When replacing any other accessory that is required to install this accessory, follow these instructions only.
3 of 5
PREPARING THE SUBHARNESS• This procedure is not required if the motorcycle
is already equipped with the subharness for other installed electrical accessories.
1. Refer to the Service Manual for the motorcycle.
Open the pillion seat to remove the rider seat.
2. Remove the left panel.
3. Remove the left front side cowl and disconnect the connector.
5. Remove the left side cover.
4. Remove the center cover.
RIDER SEAT
BOLT
PILLION SEATOpen.
LEFT PANEL
SCREW
LEFT FRONT SIDE COWL
CLIP
BOLT
BOLT
CONNECTORDisconnect.
CLIP
CENTER COVER
BOLT
LEFT SIDE COVER
BOLT
CLIP
4 of 5
8. Secure the 6-pin waterproof connector with the wire ties and electrical tape as shown.
7. Connect the subharness as shown.
6. Release the motorcycle’s 6-pin waterproof connector as shown.
MOTORCYCLE’S 6-PIN WATERPROOF CONNECTOR
LUGGAGE BOX
MOTORCYCLE’S HARNESS
SUBHARNESS
WIRE TIE (narrow)SUBHARNESS
MOTORCYCLE’S CLAMP
MOTORCYCLE’S HARNESS
ELECTRICAL TAPESecure to the motorcycle’s harness.
ACCESSORY SOCKET
SOCKET RING
CAPClose the cap when it is not used.
Mark with an awl in the position shown.
ELECTRIC DRILL(30 mm HOLE SAW)
Drill at the marked point.
ACCESSORY SOCKET INSTALLATION1. Drill a 30 mm hole along the factory marked line
(point) shown using an electric drill and hole saw.
• Remove the burrs from the edge of the hole.
2. Install the accessory socket as shown.
FACTORY MARKED LINE
FACTORY MARKED POINT
AWL
30 mm
ELECTRICAL TAPEBundle the subharness.
5 of 5
4. Cover the connectors with the harness boot as shown.
5. Secure the subharness with the wire tie as shown.
WIRE TIE(Included with the Subharness.)
Secure to the motorcycle’s harness.
3. Connect the accessory harness as shown. 6. Bundle the socket harness and secure it with the wire tie as shown.
7. Install the motorcycle’s parts in the reverse order of removal.
• Confirm that the harness is not caught or too tight.
8. Attach the caution label in the position shown.
ACCESSORY HARNESS
SOCKET HARNESS SUBHARNESS
ACCESSORY HARNESS
SOCKET HARNESS
HARNESS BOOT
SUBHARNESS
MOTORCYCLE’S HARNESS
SOCKET HARNESS
WIRE TIE (wide)Secure the socket harness to the motorcycle’s harness.
MOTORCYCLE’S HARNESS
SAFETY INFORMATION LABELBefore attaching, thoroughly clean the area where the caution label will be attached.
Recommended