View
7
Download
0
Category
Preview:
Citation preview
The next generationmeasurement solution
DEWEnet Instruments GmbH
Franz Degen, CEO
2
Company background:1989: Franz Degen founded DEWETRON GmbH Austria, together with Herbert Wernigg, and brought the PC instrument to the market where the personal computer and the data acquisition hardware where combined in one box. DEWETRON GmbH is still selling this technology with improvements today.
2000: Franz Degen founded DEWESoft d.o.o. together with Dr. Jure Knez, Andrej Orozen and Herbert Wernigg. The focus was first the Instrument Software, than in 2010 followed by dedicated hardware on USB interface and later on Ethercat.
2018: Franz Degen follows the “INFORMATION TECHNOLOGY trend” and offers the ODOS cloud based data acquisition. The precision CAN bus hardware is designed and manufactured at the partner company TVE Vienna Austria. The TVE precision hardware and the ODOS software is the base for the “NEXT GENERATION MEASUREMENT SOLUTION” .
Franz Degen built up a worldwide sales and support team all over the world for test and measurement solutions the past 30 years. It is very easy for this worldwide test and measurement team, to learn how to use the latest IT technology, and bring this knowledge to the existing R&D customer. We know from our customers the additional requirements for the CAN bus market, which we have implemented in our new measurement hardware and the CAN sensors.Joachim Englund, CEO of ODOSOLUTIONS / Sweden, with the same test and measurement background, developed the cloud based data acquisition analysis and presentation software, and sold this successful already to key customers in England and Sweden.TVE elektronische Systeme GmbH in Vienna Austria is the base for most of the precision hardware designed and manufactured for DEWETRON, DEWESoft® and more.The CO-OPERATION of ODOSOLUTIONS software, TVE hardware, and the worldwide sales network from Franz Degen, is the base for the new DEWEnet company in Austria. DEWEnet holds the exclusive worldwide sales rights for all TVE products, and the exclusive rights for the ODOS solution in ASIA. In Europe and the Americas ODOS cooperates with DEWEnet Instruments GmbH.
1989 2000 2010 2018 ... more to come in the next years
Founded DEWETRON GmbH Austria
Founded DEWESoft d.o.o.
DEWESoft® measurement software
DEWESoft® measurement hardware
Cloud based measurement solutions
CAN bus hardware
Combined computer and
d
ata acquisition hardware
The next generation “measurement solution“
DEWEnet Instruments GmbH Measurement Solutions Overview
SOFTWARE
HARDWARE
APPLICATIONS
ODOS cloud based data acquisition (page 4-8)
CAN-,dbc data export, connectivity (page 9)
LabVIEW® (page 10)
TVE hardware manufacturing (page 11-12)
ODOS MicroLog (page 5)
CANLOG high channel count DAQ (page 13-20)
CANLOG waterproof high channel count DAQ (page 13-20)
S-CAN single CAN DAQ modules (page 13-20)
Accessories (page 21)
EV-POWER-x00A Voltage and current sensors for electrical vehicles (page 22)
FUSE Adapter DN-SHUNT (page 23)
Battery Testing (page 24)
Energy & Efficiency Analysis of Electric Vehicles (page 25)
AC & DC Power Analysis of Electric Vehicles (page 26)
Heating, Ventilation, Air Conditioning testing (HVAC) (page 27)
Proving ground monitoring (page 28)
Fleet management monitoring (page 29)
Channel Expansion (page 30)
Configuration examples (page 31)
Battery Energy 90 %
33 %
29 %
30 %
Charging/Discharging losses 10 %
4 % DC/DC
Air Conditioning
1 % Losses
Motor 2
Motor 1
+ 40° C
Grid Energy 100 %
26 %
23 %
48 %
Battery Energy 90 %
Charging/Discharging losses 10 %
2% DC/DC
Air Conditioning
1 % Losses
Motor 2
Motor 1
- 20° C
Grid Energy 100 %
REPORT
3
... more to come in the next years
Access your data at any time, at any place on the globe
Joachim Englund, ODOS
SOFTWARE HARDWARE APPLICATIONS
We learned from the telecommunication market, that we get all information at any time at any place on the globe! So why not expecting this in the test and measurement world as well?DEWEnet offers data acquisition solutions all over the globe with the access to the measured data at any time, at any place.We deliver the measuring hardware with the WORLDWIDE SIMCARD INCLUDED! With an incredible price! Please just ask us for the system quotation!With our great experience in the automotive R&D market, our first customers are in this area as well. However we get great requests from similar applications, especially in remote area with difficult access like wind mills, cranes, civil engineering applications just as the start.
4
Access your data at any time, at any place on the globe Measure anywhere on the globe
The first target was to measure, store and analyze the INVEHICLE already available data. All the new vehicles have the built in OBDII connector where standard data for vehicle speed, engine RPM and many other vehicle data are available on the CAN bus. The ODOS MicroLog acquires all this data and decode that standard values, but with the additional CAR dbc – file all the data in the car can be stored and analyzed later. Additionally the error messages can be analyzed and errors even reset remotely. The built in GPS receiver stores the position at any time as well.
ODOS MicroLog sends the data direct to the cloud with the built in WORLDWIDE DATA SIM CARD. ODOS MicroLog includes additionally a small data buffer, a battery and acceleration sensor. For vehicle applications it is guaranteed that data are transferred and stored only, as long as the vehicle is moving.
The functionality of the 2 CAN ports is free programmable. For example Port 1 is used for OBDII and Port 2 is used for connecting additional data acquisition systems to measure additional signals.DEWEnet offers a complete range of CAN bus data acquisition solutions as well as CAN bus sensors!
OBD2
4G Modem
GPS Sirf V Chip
Dual CAN
Accelerometer
UDS ISO 14229
CANdb
CAN Traffic
J1939
GeneralModem 4G default, 2G or 3G on request
CAN input 1 CAN-HS 2.0B default; 2nd CAN port is optional
Battery 450mAh
GPS Sirf Atlas V (assisted GPS enabled) Sensitivity : -161dBm, 64 channels
Built in Bluetooth 2.1 & 4.0 LE* (4G version only) client and hotspot (4G version only)
WIFI WIFI client and hotspot*
Data Buffer Onboard 42 MB
3D Accelerometer Full scale output range: ±2g; ±4g; ±8g; ±16g 12 bits - low temperature drift – good linearity
PluginsOBD2 Complete channel list for Mode 0x1. Support Mode 0x1,0x3,0x6,0x9
CAN monitor Support import of CAN data base files. With or without syntax check.
UDS ISO 14229 Diagnostics supporting service 19,22,14. Description files GDX,ODX.
CAN Traffic Possibility to store complete CAN bus with pre and post trigger buffer.
K-line Request data from older generation vehicles.
J1939 Support import of J1939 CANdb files
DimensionsOperating Temperature -30°C .. +65°C
Current ConsumptionSleep 2 mA/Hibernate=700 μA
During sleep Internal battery is used. Device runs 8 days on battery in idle mode.
Supply Voltage 8 .. 32 V
Dimensions (mm) 27 x 48 x 49.5 without connector 60.5 x 26.5 x 49.5 with connector
SOFTWARE HARDWARE APPLICATIONS
5
Dashboard
Analysis DTC AUDITOR Realtime view
Example with Vehicle speed Engine RPM GPS position.
Iphone and Android phone friendly
Dashboard Features
Dashboard Example
Mobile Phone Support
SOFTWARE HARDWARE APPLICATIONS
6
SOFTWARE HARDWARE APPLICATIONS
7
“ODOS data acquisition solution” - Easy to install
User groups
Analyse
DEWEnet delivers the predefined protected customized ODOS MicroLog, so that the customer just needs to connect it to the ODBII connector.
The customer defines the
ODOS MicroLog GROUP
PASSWORD GROUP and
Plugins for the optional analysis features.
Seconds after the installation, the data is stored in the cloud, ready for online and offline analysis.
The user group: example with 10 vehicles
See their locations
This “dashboard example” shows one trip with just 2 channels, vehicle speed and engine RPM and GPS position.
Reports
Realtime Display
Plugin Concept
DTC Auditor
Configurator
Alerts and trigger module
Data Export Module
Signal and GPS Analysis
Admin and User Accounts
SOFTWARE HARDWARE APPLICATIONS
Features & Plugins
8
ODOS packages PACKAGE LIGHT PACKAGE BASIC PACKAGE PLUS PACKAGE PROFeatures
Server Instance AWSData Pipeline MFT to Server
AWS Backup Days 30 30 60 90Markers
DTC AuditorData ConverterMail and Alerts
Report GeneratorCustom Branding color Dashboard
SIM CARD EU Plugins
OBD2 Plug InCANdb Plug InJ1939 Plug InK-line Plug In
GM lan Plug InUDS Plug InGPS Plug InFMS Plug In
CAN Traffic Plug In
What our clients are saying
Alexander Müller · Durability testing Johan Andersson · Electrical Testing
Steve Smith · Powertrain calibration
”We use the system for mileage accumulation and we are really happy with the easy and quick access to our vehicles and the automatic report from the daily trips”
”During the built process we install one logger in each prototype, we can now easily follow the status of the vehicle, DTC´s and other interesting data. The marker feature is brilliant to make notes during the drive with the smartphone!”
”With prototypes all around the world we needed a system to follow our vehicles realtime it´s perfect especially as we now can compare data from different test conditions in realtime”
SOFTWARE HARDWARE APPLICATIONS
4G
Easy connection to any CAN readable software package via DBC file
CLOUD SOLUTION
easy & fast integration predefined dbc files Config Tool with dbc export
Fleet Testing Database Storage Online Live Data View
Incl. OBDII data Incl. GPS data Incl. easy to use data viewer Incl. data reporting
to DEWESoft®
to INCA (ETAS®)to CANape® (Vector®)to IPEmotion® (IPEtronik®)to LabView® (NI®)to DASYlab® (NI®)to any testbed software
CAN with .dbc file
Connectivity - Software
As soon as the CANLOG setup is done either in the browser based application or with DEWESoft®, just with one mouseclick the .dbc file can be generated. With this .dbc file the CANLOG can be connected to all the popular CAN acquisition packages.
LabVIEW® Repeatable Test procedures Customer-specific solutions Test-Bed operation
ideal for fleet testing
ideal for repeatable test procedures
9
SOFTWARE HARDWARE APPLICATIONS
LabVIEW®
10
User Interfaces
Manipulate front panels programmatically Configure and manage VIs to execute outside the editorUse new controls
Software Engineering
Execute and control VIs dynamicallyAbstract code with object-oriented programmingCompare VI source code with Diff ToolUse more event-driven programming options
Systems Management
Connect, configure, and document hardware graphically with SystemDesignerDesign hardware systems offline from a catalog of NI hardware
Web Technology
Create simple browser-based HMIs using Web VIs for system configuration and operator interfacesUse Data Service APIs for Device to HMI communication
Hardware Support
Control additional benchtop instrumentsUse additional electronic test and RF instrumentationIntegrate machine vision hardware
Custom Algorithm Design
Design custom machine vision algorithms
Distributed Applications
Build and distribute EXEs, libraries, and installers
Interoperability
Integrate LabVIEW NXG code with TestStandCall external DLLs
Data Management
Publish tags and messages using simplified data communication VIs
Herbert PiribauerCo-founder, TVE GmbH Vienna
Erwin RodeCEO, TVE GmbH Vienna
CONTINUOUS SOFTWARE TESTING
SOFTWARE HARDWARE APPLICATIONS
CAN data acquisition based TVE experience
11
The hardware is based on the more than 30 years experience of “TVE elektronische Systeme GMBH in Vienna Austria, in developent, producton, testing and calibration of “precision signal conditioners” for many instruments customers.
The analogue galvanic isolation of all amplifiers for many well known customers in the R&D market, are all based on the design and manufacturing of the TVE planar transformer. More than 100,000 TVE planar transformers are in use from key R&D centers worldwide, sold from the few precision signal conditioning companies.The latest high speed transformer has unique specifications on the globe: Dynamic up to 90 dB Bandwidth 2 MHz.
Latest technology used Prepared for easy onsite FW upgradingOur programmers are speaking many programming languages, assembler to talk direct to the hardware, advanced experienced FPGA programming and several application programming languages.
We continue to improve our instruments performance. The user may choose onsite to use new features with easy onsite firmware updating just via USB.
Each programmer has the task to test the code generated by his colleague. Additionally the full functional test is done by the application engineer.
SOFTWARE HARDWARE APPLICATIONS
PCB production
12
Best stock with all components
Fastest on-time production
Experienced manufacturing team
On- time delivery is very important in this new “fast time to market”TVE GmbH has far above 5 Million components on stock, to make sure that we are prepared for the fastest delivery. Because some compo-nents may have a delivery time of more than 40 weeks, this stock management is very im-portant for the customer satisfaction!
The perfect pick and place machine can be prepared for most PCB`s in less than 1 day. This makes sure that the whole instruments production flow is guaranteed in shortest pos-sible time.
Vienna is well known as one of the European electronics R&D and manufacturing centers. TVE GmbH used the chance to hire this well experienced engineers already the last 30 years.
SOFTWARE HARDWARE APPLICATIONS
ODOS MicroLog
CANLOG
CANLOGw (waterproof)
S-CAN single slices
EV-POWER-X00A
FUSE ADAPTER DN-SHUNT
Dual CAN port with modem for world wide data connectivity Multi protocol Support OBDII, J1939, UDS, DTC, CAN-dB… Built in GPS and Accelerometer
Up to 64 channels (configurable types) per enclosure Highest precision and low power consumption CAN data output and parallel integrated logging
Rugged and waterproofed version of CANLOG Highest precision and low power consumption CAN data output and parallel integrated logging
Distributed CAN based measurement Connection for any sensor Fully compatible with CANLOG series
Current sensing from 50 mA to 1000 A Voltage up to 1000 V Power, Energy, Efficiency Plug & Play
Easy Current measurement inside vehicles Adaptercables for each car fuse type Short-circuit protection maintained Connection to any DAQ system possible
Hardware Overview
13
SOFTWARE HARDWARE APPLICATIONS
14
Measure any additional signal with CANLOG
Analog Inputs CANLOG CANLOGw (waterproof ) S-CANMeasurement
modules8 4 8 4 1
System Sample rate 0.01 Hz to 1000 Hz/channel
CAN Bus Baudrates 50, 100, 125, 200, 250, 333.33, 500 and 1000 kBaudData format on
USB loggingopen .csv format for Excel®, LabVIEW®, MATLAB®, DIAdem®, FlexPro® and many more
Supply voltage 8 .. 60 VDC (6VDC when operating), Current limited to 4 AmperePower consumption
(excluding modules)1.5 W -
System bus connector 2x Lemo 1B 4 pin for CAN and power supply
Logging function USB type for stick; Lemo 00 4-pin for start/stop logging -
Temperature range -40°C .. +85°C
Relative humidity 5 to 95 % (non condensing)
IP protection IP 44 IP 65
Dimensions 265 x 164 x 111 mm 162 x 164 x 111 mm 279 x 170 x 131 mm 177 x 170 x 131 mm 170 x 110 x 29 mmWeight
(excluding modules)1.8 kg 1.2 kg 2.5 kg 1.8 kg 0.56 kg
Instruments
SOFTWARE HARDWARE APPLICATIONS
15
Measure any additional signal with CANLOG
Modules overviewTH8-K TH8-UNI STG4-S CNT4 LV4 LV6 RTD6
Input channels8 type K
thermocouple 8 universal
thermocouple4 Strain gage
4 counter 12 digital inputs
4 low voltage, separate exc.
6 low voltage, common exc.
6 universal RTD
Measurement types
Thermocouple, voltage
Thermocouple, voltage
Full-, half bridge
Event counting, frequency, duty cycle, PWM, DI
Voltage, current
Voltage, current
Temperature (all RTD types),
Resistance
Input ranges±15 mV .. 1.5 V -270 .. 1350°C
±15 mV .. 1.5 V FS on TC type
± 20 mV/V350 kHz,
32 bit counter±100 mV .. 60 V,
± 30 mA±100 mV .. 60 V,
± 30 mA-200°C .. 850°C;
2, 20 kΩ
Sensor excitation - -2.5 VDC or
2.5 VAC
2 .. 15 V (max. 100 mA)
0 V .. ±15 V, 60 mA
max. 0.6 W/Ch
0 V .. ±15 V, 100 mA,
max. 1.5 W total100 µA or 500 µA
Input connector mini TC mini TC 10 pin Lemo 1B 7 pin Lemo 1B 7 pin Lemo 1B 7 pin Lemo 1B 7 pin Lemo 1B
System Sample rate
1000 S/sec 1000 S/sec 1000 S/sec 1000 S/sec 1000 S/sec 1000 S/sec 1000 S/sec
Isolation voltage 500 VDC 500 VDC 500 VDC 200 VDC 500 VDC 500 VDC 500 VDC
Power consumption
(max.)0,65 (1) W 0,65 (1) W 2.7 (3.5) W 2 (10) W 2.3 (9) W 1.9 (4) W 0.8 W
Environmental
Operating temperature
-40°C ..+85°C -40°C ..+85°C -40°C ..+85°C1) -40°C .. +85°C1) -40°C .. +85°C1) -40°C .. +85°C1) -40°C .. +85°C
Relative humidity 5 to 95 % (non condensing)1) -40°C .. +70°C with full excitation power
StrainCounter
Power
GPSTemperature
Vibration
OBDII
CAN
Current
Recuperation
Voltage
Energy
4G
Cloud storage with easy-to-use data view & report
TH8-K TH8-UNI
SOFTWARE HARDWARE APPLICATIONS
TH8-K TH8-UNIChannels 8 type K thermocouple and voltage 8 universal thermocouple and voltage
ADC type 24 bit delta-sigma
System Sample rate 1000 S/sec, simultaneous
Thermocouple Type K Type J, K, T, E, R, S, B, N
Accuracy ±0.02 % of reading ±0.5°C ±5 μV ±0.02 % of reading ±1°C ±10 μV
Resolution 0.025°C 0.01 .. 0.03°C (depending on TC type)
Temperature range -270°C .. 1372°C Full scale of thermocouple type
Typical noise at 200 S/s (10 S/s) 0.1 (0.02)°CRMS
Voltage ranges ±15 mV to ±1.5V ±15 mV to ±1.5V
Accuracy ±0.02 % of reading ±20 µV ±0.02 % of reading ±10 µV
Typical Noise at 200 S/s (10 S/s) 4 µVRMS (0.8 µVRMS)
Gain drift Typ. 3 ppm/K (max. 10 ppm/K)
Offset drift 0.04 µV/K
Input coupling DC
Input impedance / current 100 MΩ / 18 nA
General
Max. input voltage ±25 V (±500 V peak)
Isolation voltage ±500 V channel/ground & channel/channel
Bandwidth 50 Hz min.
Power consumption 0.7 W typ. (1 W max.)
Input connector mini thermocouple connector mini thermocouple connector (cu)
Environmental
Weight 82 g (S-CAN 560 g)
Operating temperature -40°C .. +85°C
CLw-TH8-K CL-TH8-KCLw-TH8-UNI CL-TH8-UNI
8 isolated thermocouple or voltage inputs
1000 S/sec simultaneous sampling rate
High accuracy type K or universal input type
CJC on each channel
S-CAN-TH8-UNI
S-CAN-TH8-K
16
SOFTWARE HARDWARE APPLICATIONS
CLw-STG4-S CL-STG4-S
Highest precision isolated strain gage input
DC or AC (square) excitation
Static strain measurements (automatic drift compensation)
1000 S/sec simultaneous sampling rate
STG4-SChannels 4 Strain gage for full bridge (6 or 4 wire) or half bridge (3 or 5 wire)
ADC Type 24 bit delta-sigma
System Sample rate 1000 S/sec, simultaneous (50 S/sec AC excitation)
Bridge ±40 mV/V
Accuracy ±0.03 % of reading ±1 µV/V( @DC excitation)
Typical noise at 200 S/s (10 S/s) 0.05 µV/VRMS (0.01 µV/VRMS)
Gain drift Typ. 2 ppm/K (max. 5 ppm/K)
Offset drift 0.04 µV/V/K @ DC excitation, 0.00 µV/V/K@AC excitation
Input coupling DC
Input impedance 1 GΩ
Excitation +2.5 VDC or 2.5 VAC (Square)
Current limit 30 mA
Accuracy ±1 mV
Excitation drift 25 ppm/K
Protection Continuous short to ground
General
Isolation voltage ±500 V channel/ground & channel/channel
Bandwidth 50 Hz DC excitation, 12 Hz AC excitation
Power consumption 2.7 W 1000 Ω full bridge, 3.5 W 120 Ω full bridge
Input connector Lemo 1B, 10 pin
Environmental
Weight 135 g (S-CAN 560 g)
Operating temperature -40°C .. +85°C (-40°C .. +75°C with 120 R bridge resistance)
17
STG4-SS-CAN-STG4-S
SOFTWARE HARDWARE APPLICATIONS
CNT4
CLw-CNT4 CL-CNT4
4 multifunctional isolated counter channels or digital inputs
Simultaneous counting and frequency mode out of one input
Programmable threshold levels with AC/DC coupling
Programmable sensor excitation (per channel)
CNT-4Channels 4 counter or 12 digital inputs with 4 Auxiliary output channels
Resolution 10 nsec time base, 40 bit internal resolution
System Sample rate 1000 S/sec, simultaneous
Measurement modes
Event counting functions Simple Event, Gated, Up/Down counter, encoder (X1, X2, X4)
Period, high, low, duty cycle, edge separation 200 nsec to 42.9 sec
Frequency measurement 0.0001 Hz to 350 kHz
4 Auxiliary output channels Additional measurement from any channel: eg. counter and frequency at once
Signal input
Programmable high and low level ±40 V threshold with ±200 mV tolerance
Input coupling DC or AC (0.5 Hz)
Max. input voltage ±200 V (400 V peak)
Control signal A/B
Input compatibility TTL (Low: <0.8 V, High: >2 V)
Max. input voltage ±200 V (400 V peak)
Excitation +0, 1.5, 2, 2.5, 3.3 5, 7.5, 10, 12.5 and 15 V
Current limit 100 mA
Accuracy ±3 %, ±50 mV
Protection Continuous short to ground
General
Time base accuracy 2 ppm
Isolation voltage ±200 V channel/ground & channel/channel
Power consumption 2.2 W without sensor supply, 10 W max.
Input connector Lemo 1B, 7 pin
Environmental
Weight 125 g (S-CAN 560 g)
Operating temperature -40°C .. +85°C (-40°C .. +70°C with total excitation power >1.5 W)
S-CAN-CNT4
18
SOFTWARE HARDWARE APPLICATIONS
High precision isolated voltage or current inputs
4 or 6 isolated channels
1000 S/sec simultaneous sampling rate
Programmable excitation (independent, LV4)
LV6 LV4
LV6 LV4Channels 6 voltage or current 4 voltage or current
ADC type 24 bit delta-sigma
System Sample rate 1000 S/sec, simultaneous
Voltage ranges ±100 mV to ±60 V
Accuracy ±0.05 % of reading ±0.5 mV
Typical Noise at 100 Hz (10 Hz) Filter 75 µVRMS (15 µVRMS)
Gain drift Typ. 10 ppm/K (max. 30 ppm/K)
Offset drift 1µV/K
Input coupling DC
Input impedance 1 MΩ
Common mode voltage 30 V to EXC, 500 V peak to GND
Current range ±30 mA
Accuracy ±0.1% of reading ±0.05 mA
Typical noise at 200 S/s (10 S/s) 12 µARMS (2 µARMS)
Input impedance 50 Ω, ±0.1%
Excitation ±0, 0.5, 1.25, 2.5, 5, 7.5, 10, 12.5 and 15V
Current limit 100 mA (1.5 W max.) per module (common excitation for module)
60 mA (0.8 W max.) per channel (separate excitation on each channel)
Accuracy ±1% of value ±20 mV
Excitation drift 50 ppm/K
Protection Continuous short to ground
General
Max. input voltage ±100 V (±400 V peak, 100 msec)
Isolation voltage ±500 V channel/ground & channel/channel
Bandwidth 50 Hz min.
Power consumption (full excitation power) 1.9 (4) W 2.3 (7) W
Input connector Lemo 1B, 7 pin
Environmental
Weight 143 g (S-CAN 560 g) 123 g (S-CAN 560 g)
Operating temperature -40°C .. +85°C (-40°C .. +75°C with total excitation power > 1.5 W)
CLw-LV6 CL-LV6CLw-LV4 CL-LV4
S-CAN-LV4
S-CAN-LV6
19
RTD6
6 isolated temperature (RTD) or resistance inputs
Highest precision with DC excitation
Universal RTD inputs (PT100 .. PT 2000) or resistance up to 20 kΩ
1000 S/sec simultaneous sampling rate
RTD6Channels 6 universal RTD or resistance inputs
ADC Type 24bit delta-sigma
System Sample rate 1000 S/sec, simultaneous
Temperature
Thermistor types PT100, PT200, PT500, PT1000, PT2000 (385)
Measurement Range -200°C to +850°C
Accuracy ±0.15°C ±0.05% of reading
Temperature drift 0.01°C/K
Excitation 500 µA for PT100 and PT200, 100 µA for PT500, PT1000 and PT2000
Input connection 2 wire or 4 wire
Resistance
Measurement Range 2 kΩ or 20 kΩ
Accuracy ±0.02% of reading ±0.01% of range
Input connection 2 wire or 4 wire
General
Isolation Voltage ±500 V channel/ground & channel/channel
Bandwidth 200 Hz
Power Consumption 0.8 W
Input Connector Lemo 1B, 7 pin
Environmental
Weight 143 g (S-CAN 570 g)
Operating temperature -40°C .. +85°C
CLw-RTD6 CL-RTD6
S-CAN-RTD6
SOFTWARE HARDWARE APPLICATIONS
20
SOFTWARE HARDWARE APPLICATIONS
System Cables
CL-L1B4m-L1B4m-M5 CANLOG system daisy chain cable for CAN and Power, length = 0.5 m
CL-L1B4m-L1B4m-2M CANLOG system daisy chain cable for CAN and Power, length = 2 m
CL-L1B4m-L1B4m-5M CANLOG system daisy chain cable for CAN and Power, length = 5 m
CL-CAN-L1B4m-D9fT-3M CANLOG Data-cable for CAN from Lemo 1B to DB9 female, incl. 120R CAN determin., length = 3 m
CL-CAN-L1B4m-OPEN-3M CANLOG Data-cable for CAN from Lemo 1B to open end, length = 3 m
CL-PWR-L1B4m-BN-3M CANLOG supply cable from Lemo 1B to Banana plug, including 120R CAN termination, length = 3 m
CL-PWR-L1B4m-CIG-3M CANLOG supply cable from Lemo 1B to cigarette lighter, including 120R CAN termin., length = 3 m
CL-PWR-L1B4m-OPEN-3M CANLOG supply cable from Lemo 1B to open end, including 120R CAN termination, length = 3 m
CL-CTR-00-OPEN-3M CANLOG control cable from Lemo 00 to open end, for start/stop of logging function, length = 3 m
CL-TRM-L1B4m CANLOG termination plug for CAN-bus with 120 R
CL-UPS-70WInput Voltage 10 .. 36 VDC
Output Voltage (Battery mode) 24 VDC (12 – 16 VDC)
Max. Output Power 70 W
Battery Type Lithium Ion Smart Battery
Battery Capacity 6.8 Ah / 90 Wh
Operating Temperature -20°C .. +60°C (discharge)
0°C .. +60 °C (charge) CANLOG supply cable from Lemo 1B to cigarette lighter, including 120 R CAN termination, length = 3 m
Dimension (L x W x H) 204 x 104.6 x 67.3 mm
Weight 2.2 kg
CL-UPS-70W
Power supply
21
Accessories
EV-POWER-x00A
Current sensing from 50 mA to 1000 A
Voltage up to 1000 V
Power, Energy, Efficiency
Plug & Play
SOFTWARE HARDWARE APPLICATIONS
EV-POWER-x00ACurrent
Type EV-POWER-100A EV-POWER-500A EV-POWER-1000A A
Measurement range ±100 ±500 ±1000 A
Typical accuracy ±0.1 %reading
Total accuracy ±0.5 %reading
Resolution 5 30 50 mA
Voltage
Voltage range ± 1000 V
Typical accuracy ± 0.1 % of reading
Total accuracy ± 0.5 % of reading
Resolution 30 mV
Safety category CAT II 1000 V / CAT III 600 V
Power & Energy
Typical accuracy ±0.2 %reading
Total accuracy ±0.7 %reading
Analog Inputs
AD conversion 16 bit
Sampling rate 4 kHz
Communication CANbus 2.0
Output rate 1 kHz*, 500 Hz, 100 Hz, 10 Hz, 1 Hz
Output channels Current, Voltage, Temperature
Operating ConditionsOperating temperature -40°C .. +100°C
Current consumption 30 mA .. 80 mASupply voltage 5.5 V .. 40 V
Dimensions 123x96x38mm (EV-POWER-100A) / 185x115x56mm (EV-POWER-500A)Protection IP54
* only current selected
22
SOFTWARE HARDWARE APPLICATIONS
23
Fuse Adapter DN-SHUNTCurrent Measurement Connection
Maximal Current Resistance Connection Cable Length 1m or 3m
10 A 5 mΩ Connector to DAQ system DSUB9 or LEMO including TEDS
25 A 2 mΩ Fuse Replacement ATO 10 A to 25 A; JCASE for 40 A to 60 A
40 A 1 mΩ Environmental
60 A 0.5 mΩ Operating Temperature -40°C … +70°C
Typical Accuracy 0.2% of reading with TEDS Humidity 85 % RH
Temperature Drift < 50 ppm/K Dimensions 55 x 32 x 54 mm
MAXI
MINI.L
MICRO2
MINI
ATO
MICRO3ON REQUEST
JCASE
OPEN END
Car fuse measurement box with integrated shunt
Note: High Current protection of vehicle has to be ensured by using appropriate exchangeable fuse.
Fuse cable exchangeable Shunt measurement box Connectivity to any DAQ system
Fuse exchangeable
Fuse Adapter DN-SHUNT
Easy Current measurement inside vehicles
Adaptercables for each car fuse type
Short-circuit protection maintained
Connection to any DAQ system possible
Battery Testing
SOFTWARE HARDWARE APPLICATIONS
SYNCHRONOUS ACQUISITION OF MULTIPLE PARAMETERS: Voltage
Current
Power / Energy
Temperature
Humidity
Pressure
Vibration
Force
Thermal imaging camera
High-speed camera
Data logging, cell characterization
Charge-discharge analysis, charging profile
Energy, efficiency, losses, recuperation
Misuse, endurance & aging test
24
Cred
its: U
.S. D
epar
tmen
t of E
nerg
y
The battery as central element in the electrical powertrain, strongly affects performance and range of electric vehicles. Extensive tests are necessary: From the cell-characteristics up to testing of the whole battery packs. Detailed analysis requires measurement of different parameters (temperature, voltage, current, etc.) at multiple points. The flexible and scalable solution from DEWEnet allows to measure more than 1000 channels within one instrument, perfectly synchronised. DEWEnet measurement instruments are the perfect fit for R&D applications as well as for battery monitoring applications.
Energy & Efficiency Analysis of Electric Vehicles
SOFTWARE HARDWARE APPLICATIONS
Battery Energy 90 %
33 %
29 %
30 %
Charging/Discharging losses 10 %
4 % DC/DC
Air Conditioning
1 % Losses
Motor 2
Motor 1
+ 40° C
Grid Energy 100 %
26 %
23 %
48 %
Battery Energy 90 %
Charging/Discharging losses 10 %
2% DC/DC
Air Conditioning
1 % Losses
Motor 2
Motor 1
- 20° C
Grid Energy 100 %
REPORT
CAN/USB converter
ODOS MicroLog
EV-POWER-x00ACurrent, Voltage, Power
High-precise current & voltage measurement
Easy-to-mount and flexible sensors (battery, PTC, AC,…)
Automatic energy balance report
The EV-POWER sensors are designed exactly for the needs of accurate energy consumption measurements at electric vehicles – at all driving conditions. The sensors are easy-to-mount (any kind of HV connector possible) and safe measurements are ensured. There are no modifications at the vehicles needed and no high-voltage measurement cables need to be guided inside the motor- or compartment room. Shunt-based current sensing with automatic temperature correction allows measuring very low currents (50 mA) as well, as very high currents (500 A) for the whole operating temperature range with highest accuracy - without any influence of shielded motor cables. The Report Generator gives you an excellent overview of your electric vehicle - detailed analysis for different driving situations (e.g. energy consumption from 40 to 50 km/h) as well as energy balance charts, statistics and motor evaluations are just some of the features.
Basic Energy Report
Low Voltage Energy Report
Driving Situation Analysis
Energy Balance Diagram
25
Energy Report for 12V/24V/48V Example: 12 V Battery,
Waterpump, Fans, Blower, DC/DC, Auxiliaries, …
Special Energy Analysis for Speed classes (40-50 km/h, 50-60 km/h…) Uphill / Downhill Energy Recuperation
101520253035
mk001/hWk
noitpmusnoc
ygrenE
Electric test vehicle
26 %
23 %
48 %
Battery Energy 90 %
Charging/Discharging losses 10 %2% DC/DC
Air Conditioning
1 % Losses
Motor 2
Motor 1
- 20° C
Grid Energy 100 %
Energy (Min, Max, Ave, specific) Power (Min, Max, Ave) Recuperation Efficiency Table Torque, Speed, Velocity, Altitude Temperature, Weather, GPS track
Sankey Diagram for Energy flow
Cred
its: U
.S. D
epar
tmen
t of E
nerg
y
AC & DC Power Analysis of Electric Vehicles
SOFTWARE HARDWARE APPLICATIONS
Combination of high-speed (1MS) and low speed sampling (1kS)
High-precise AC & DC power analysis for any kind of drivetrain
Motor & inverter evaluation
The EV-POWER sensors in combination with the any Power Analyser, are the perfect tool for comprehensive testing on electric vehicles. The EV-POWER sensor can be used for measurement of all DC loads (Battery, PTC, A/C, etc.) and the DS Power Analyser for measurement at the motor / inverter. The DS Power Analyser allows precise Motor Evaluation (Efficiency, Losses, Unbalance, Efficiency Mapping,…), Inverter Evaluation (DQ Transformation, Power Quality) and other features like Raw Data Storing, Transient recording. Additionally any kind of other signals can be measured, like mechanical data, GPS, CAN , video. The flexibile hardware approach allows analysis for any kind of drivetrain (1-12 phase AC motors, hybrid, hydrogen vehicles).
Inverter
Motor3-Phase
AC OutputDC Input
Power Analysis
DQ-Transformation
Power Quality
FFT-Analysis
Raw data storing
Combustion analysis
Motor Evaluation
Efficiency Mapping
P, Q, S, PF, co phi, ... more than 100 calculated chs.
Real time Clarke and Park transformation
Scope and Vector scope
Testbed and in-vehicle measurement
FFT, Harmonics, Interharm., THD, unbalance ... AC Power / Motor Losses / Power Quality Analysis
2D and 3D FFT analysis DQ Transformation
26
DC measurement Any AC Power Analyser
118,216
241,681
114,358119,799
112,26810,2281
241,681
241,681
241,681
114,358
114,358
114,358
119,799
119,799
119,799
112,268
112,268
112,268
10,2281
10,2281
10,2281
value 5
value 3
value 4
value 2
value 1
Heating, Ventilation, Air Conditioning Testing (HVAC)
SOFTWARE HARDWARE APPLICATIONS
Compact high channel count systems (CANLOG-8)
Distributed Single CAN module (S-CAN-xxx)
Direct interface to INCA®, CANape®, DEWESoft®
Optional logging to USB stick on CANLOG-8.
Any sensor connection including sensor supply Any temperature sensor (thermocouple with TH8-UNI or PT100 with RTD6) Any counter sensor (CNT4) Any voltage or current output sensor (LV4)
Testing of the HVAC system on a vehicle requires more than 200 measurement points distributed over the complete vehicle. Compact high channel count boxes combined with small single modules are the perfect solution for performing this tests.Beside thermocouple inputs also inputs like counter for flow rate sensors, voltage and current for pressure sensors are needed. Native CAN output for direct connection to 3rd party software packages like INCA® or CANape® is needed.
Solution
Multiple CANLOG-8 systems are connected together with S-CAN-xxx modules over a single cable including power, data and synchronization. All used sensors are supplied directly from the CANLOG system.
27
Proving Ground Monitoring
SOFTWARE HARDWARE APPLICATIONS
Customers of proving operators want to get reproducable results. So the validation of test runs get more and more important. It’s state of the art, to know the exact position and all acquired parameters of the tested vehicles at any time.
Solution
The ODOS MicroLog with built-in GPS and acceleration sensor, is connected to the vehicle via OBDII interface. Also data from DEWEnet CANLOG are transferred to the ODOS cloud. The online dashboard offers a quick overview of measured signals. Prepared reports are automatically generated and stored in pdf file format. For extensive analysis, data export filters are supported: eg. MATLAB®, ASAM-MDFx, cvs, …
Live map of vehicle position and speed Additionally vehicle diagnostic bus monitoring including DTC auditor Additionally monitoring of sensor signal using CANLOG-8
Alert monitoring
Increase the quality, traceability and evidence of durability testing
Automatic report generation (eg. pdf )
Automatic GPS signal correction using track lockup table
28
Fleet Management Monitoring
SOFTWARE HARDWARE APPLICATIONS
Fleet management is much more than just tracking the vehicle position or analyzing the driver behavior by the speed profile. Getting all relevant information from those in vehicle built-in-sensors is the key for efficient testing by minimizing the effort of additional instrumentation.The aim of this application is to analyze the maximum range of electric vehicles under different traffic situations and vehicle drivers. The ODOS MicroLog is able to read all EV relevant parameters through the diagnostic bus and send them together with the GPS information to the database.
Solution
Connect the MicroLog to the vehicle OBDII connector. The ODOS dashboard shows all vehicles on the map with the battery fuel status. Additional information is visible by mouse click.
Full screen map view showing current GPS location of all vehicles
Different user levels for data view only and system configuration
From the map view, the user is able to monitor: State of charge (%) Current remaining range (km) Current vehicle speed (kph) Current power mode status (0,4,6,7) Current seatbelt status Current charging status
29
Vehicle ID/Reg: 123.456State of charge %Remaining range (km)Vehicle speed (kph)Power mode (0,4,6,7)Seatbelt status (true/false)Charging status (true/false)
Channel Expansion
SOFTWARE HARDWARE APPLICATIONS
DAQ DEVICE
Many applications like Power- or Road load data measurement require also to measure in parallel environmental data like ambient temperature or the temperature of the DUT (device under test). Other applications needs lower speed and lower cost distributed channel expansions The low power consumption and high precision S-CAN modules are the ideally suited. Simple connect them to one free CAN port of your main DAQ system.
Simple CAN based channel expansion
High precision and low power consumption
Any sensor connection including Sensor supply Any temperature sensor (thermocouple with TH8-UNI or Pt100 with RTD6) Any counter sensor (CNT4) Any voltage or current output sensor (LV4) Strain gage based sensors (STG4-S)
Easy measurement setup
SolutionMultiple S-CAN modules are used to expand the channel count of the main DAQ system.
30
Configuration examples
SOFTWARE HARDWARE APPLICATIONS
USB-stick for logger function
Application example with ODOS MicroLog data transmission to cloud
Application example with third party software
Application example with ODOS MicroLog and parallel local USB logging
DEWESoft®
LabVIEW®
any other 3rd party software
Optional:USB-stick logger function
31
Headquarters
DEWEnet Instruments GmbHFöllinger Straße 258044 GrazAustria / Europe
Phone: +43 316 39 28 75E-Mail: support@dewenet.comWeb: www.dewenet.com
Northern Europe
ODOSOLUTIONSNohabgatan 18aBuilding 73461 53 TrollhättanSweden
Phone: +46 70 36 12209E-Mail: info@ODOSolutions.comWeb: www.ODOSolutions.com
Asia Pacific
DEWEnet CHINA Ltd.Unit 1603-1606, 16th. FloorAlliance BuildingNo. 130-136 Connaught Road Central,Sheung WanHong Kong
Phone: +852 820 88723Fax: +852 820 88726 E-Mail: support@dewenet.comWeb: www.dewenet.com ©
DEW
Enet
Instr
umen
ts Gm
bH 01
/201
9 Al
l tra
dem
arks
are a
ckno
wled
ged t
o the
prop
erty
of th
eir ow
ners.
Pr
oduc
t fea
ture
s sub
ject t
o cha
nge w
ithou
t not
ice.
Recommended