View
4
Download
0
Category
Preview:
Citation preview
Str
yker
Nailin
g
Tibial Nails
Femoral Nails
Humeral Nails
Arthrodesis Nails
Flexible NailsT2
T2®
Pocket Reference Cards
T2_BR_1_Rev1.indd 1 7/1/14 1:57 PM
General Notes
The following notes apply to all T2 IM Nails (except T2 Kids) unless separately delineated either below or on the Important Facts page for each nail. Read carefully for tips, pointers, and other facts.
1. All screw hole dimensions reference the center point of the screw.
2. Internal compression screws require a 5.0mm partially threaded screw in the oblong hole.
3. T2 8mm Nails require the use of 4mm fully threaded locking screws (distally) and 5mm (proximally).
4. T2 A/R Humeral nails require ALL 4mm locking screws.
5. T2 nails may ALL require additional reaming for the proximal (driving section) beyond 1 to 1.5mm larger than the nail diameter.
6. T2 GTN - 8, 14 & 15mm nails are special order.
T2_BR_1_Rev1.indd 2 7/1/14 1:57 PM
T2 Tibia NailRequired Instruments Instruments: • T2 Basic Long Tray
• T2 Tibia Tray • Bixcut Modular Head Reamer Kit (diameter 9 to 18 mm)a
Disposables - Sterile: Qty Description Cat No.
1 3 x 285 K-Wire (Entry) 1806-0050S 1 3 x 800 Ball Tip Guide Wireb 1806-0080S 1 Bixcut Mod Trinkle Shaft, 448mmc 0227-3000S 1 4.2 x 340 Drill Bit (Proximal Guided)d 1806-4260S 1 4.2 x 130 Drill Bit (Distal Freehand)b 1806-4280S
For Internal Compression - Partially threaded screw is required in oblong hole.
- Overdrill near cortex only with the drill below.
Qty Description Cat No.
1 5.0 x 230 Drill Bitd 1806-5000S
Notes:a. Optional: Full Bixcut Kit (diameter 6 to 22mm)b. 8mm diameter Tibia nail requires the following: • (1) 3.5 x 130 Drill Bit – Cat No: 1806-3550S for 4mm distal screws • (1) 3 x 800 Smooth Tip Guide Wire – Cat No: 1806-0090S • (1) Teflon Exchange Tube – Cat No: 1806-0073Sc. Optional: Bixcut Mod Trinkle Shaft, 510mm - Cat No: 0227-8510S Bixcut with AO shaft, 448mm – Cat No: 0226-3000S 3 x 1000 Ball Tip Guide Wire - Cat No: 1806-0085Sd. Optional: If utilizing the short Tissue Protection and Drill Sleeve, the 4.2 x 260mm Drill Bit (1806-4250S) and 5.0 x 180mm Drill Bit (1806-5010S) may be utilized.
T2_BR_1_Rev1.indd 3 7/1/14 1:57 PM
Important FactsShaft Diameter: 8, 9, 10, 11, 12, 13, 14, 15mm
Driving End Diameter: 11.5mm for shaft diameters ≤ 11mm Same as shaft diameter for all other sizes
Length: 240 to 420mm (15mm increments)
Reaming: 1 to 1.5mm larger than the nail diameter
Proximal Screw Size: 5.0mm fully threaded
Distal Screw Size: 5.0mm fully threaded4.0mm fully threaded for 8mm diameter nail only
Screw Hex Size: 3.5mm
End Caps: Fully threaded, Standard, +5, +10, +15, +20, +25, +30, +35mm(Only the fully threaded end cap locks proximal screw hole)
Internal Diameter: Shaft - 5.0mmDriving end - 8mm metric thread
Compression Screw: Advanced (8mm metric thread)
10 ° A / P slope
34
41
Herzog Bend, 10 °
2515
50mm
Distal Bend, 4 °60mm
0mm
1724
50
Driving End
No Bow
Compression Range 7mm
image of standard nail
T2_BR_1_Rev1.indd 4 7/1/14 1:57 PM
T2 Femoral Nail (Antegrade Mode) Required InstrumentsInstruments: • T2 Basic Long Tray • T2 Femoral Tray • Bixcut Modular Head Reamer Kit (diameter 9 to 18mm)a
Disposables - Sterile:
Qty Description Cat No.
1 3 x 285 K-Wire (Entry) 1806-0050S 1 3 x 1000 Ball Tip Guide Wire 1806-0085S 1 Bixcut Mod Trinkle Shaft, 448mmb 0227-3000S 1 4.2 x 340 Drill Bit (Proximal Guided) 1806-4260S 1 4.2 x 180 Drill Bit (Distal Freehand) 1806-4270S For Internal Compression - Partially threaded screw is required for oblong hole. - Overdrill near cortex only with the drill below.
Qty Description Cat No. 1 5.0 x 230 Drill Bit 1806-5000S
Notes:a. Optional: Full Bixcut Kit (diameter 6 to 22mm)b. Optional: Bixcut with AO shaft, 448mm - Cat No. 0226-3000S 8mm diameter T2 Femoral nails requires the following: • (1) 3.5 x 130 Drill Bit – Cat No: 1806-3550S for 4mm distal screws • (1) 3 x 800 Smooth Tip Guide Wire – Cat No: 1806-0090S • (1) Teflon Exchange Tube – Cat No: 1806-0073S
T2_BR_1_Rev1.indd 5 7/1/14 1:57 PM
Important FactsShaft Diameter:9, 10, 11, 12, 13, 14, 15mm(8mm diameter require special order)
Driving End Diameter: 11.5mm for shaft diameters ≤ 11mm Same as shaft diameter for all other sizes
Length:140 to 480mm (20mm increments) length 240-480mm for R1.5
Reaming:1 to 1.5mm larger than the nail diameter
Proximal Screw Size:5.0mm fully threaded
Distal Screw Size: 5.0mm fully threaded
Screw Hex Size: 3.5mm
End Caps: Standard, +5, +10, +15, +20, +25,+30, +35mm
Internal Diameter: Shaft - 5.0mm Driving End - 8mm metric thread
Compression Screw: Advanced, Standard +5, +10, +15mm (all sizes are 8mm metric thread)
(Antegrade Mode)
Driving End
50
25
0mm
0mm
Compression range 10mm
R=3.0 or 1.5m
35
45
60
T2_BR_1_Rev1.indd 6 7/1/14 1:57 PM
T2 Femoral Nail (Retrograde Mode) Required InstrumentsInstruments: • T2 Basic Long Tray • T2 Femoral Tray • Bixcut Modular Head Reamer Kit (diameter 9 to 18mm)a
Disposables - Sterile: Qty Description Cat No.
1 3 x 285 K-Wire (Entry) 1806-0050S 1 3 x 1000 Ball Tip Guide Wire 1806-0085S 1 Bixcut Mod Trinkle Shaft, 448mmb 0227-3000S 1 4.2 x 340 Drill Bit (Distal Guided) 1806-4260S 1 4.2 x 230 Drill Bit (Proximal Freehand) 1806-4290S Optional: Condyle Screws
Qty Description Cat No. 1 1.8 x 310 Condyle Screw K-Wire 0152-0218S
1 5.0 x 340 Drill Bit 1806-5020S
For Internal Compression - Partially threaded screw is required for oblong hole. - Overdrill near cortex only with the drill below.
Qty Description Cat No.
1 5.0 x 230 Drill Bit 1806-5000S
Notes:a. Optional: Full Bixcut Kit (diameter 6 to 22mm)b. Optional: Bixcut with AO shaft, 448mm – Cat No: 0226-3000S 8mm diameter Femoral nails requires the following: • (1) 3.5 x 130 Drill Bit – Cat No: 1806-3550S for 4mm distal screws • (1) 3 x 800 Smooth Tip Guide Wire – Cat No: 1806-0090S • (1) Teflon Exchange Tube – Cat No: 1806-0073S
T2_BR_1_Rev1.indd 7 7/1/14 1:57 PM
Important Facts (Retrograde Mode)
Shaft Diameter:9, 10, 11, 12, 13, 14, 15mm(8mm diameter require special order)
Driving End Diameter:11.5mm for shaft diameters ≤ 11mm Same as shaft diameter for all other sizes
Length: 140 to 480mm (20mm increments)length 240-480mm for R1.5
Reaming: 1 to 1.5mm larger than the nail diameter
Proximal Screw Size:5.0mm fully threaded
Distal Screw Size: 5.0mm fully threaded1 5.0mm condyle screws
Screw Hex Size: 3.5mm for fully and partially threaded6.3mm for condyle screws and nuts
End Caps:Standard, +5, +10, +15, +20, +25,+30, +35mm (All sizes lock screw in most distal hole)
Internal Diameter: Shaft - 5.0mmDriving end - 8mm metric thread
Compression Screw: Advanced (8mm metric thread)
Driving End
35
45
40
50
25
15
0mm
15
0mm
60
35Compression range 10mm
R=3.0 or 1.5m
T2_BR_1_Rev1.indd 8 7/1/14 1:57 PM
T2 GTN
Instruments: • T2 Basic Long Tray • GTN Indication Tray • Bixcut Modular Head Reamer Kit (Diameter 9 to 18mm)
Disposables - Sterile: Qty Description Cat No.
1 3 x 285 K-Wire (Entry) 1806-0050S 1 3 x 1000 Ball Tip Guide Wire 1806-0085S 1 Bixcut Mod Trinkle Shaft, 448mm 0227-3000S 1 4.2 x 340 Drill Bit (Proximal Guided) 1806-4260S 1 4.2 x 180 Drill Bit (Distal Freehand)b 1806-4270S
For Internal Compression - Partially threaded screw is required for oblong hole. - Overdrill near cortex only with the drill below.
Qty Description Cat No.
1 5.0 x 230 Drill Bit 1806-5000S
Notes:a. Optional: Bixcut with AO Shaft, 448mm - Cat. No: 0226-3000Sb. 8mm diameter T2 GTN Nails can only be locked with 4mm Fully threaded screws at non-driving end Use the Ø3.5 x 180mm Drill (1806-3570S) for freehand locking
T2_BR_1_Rev1.indd 9 7/1/14 1:57 PM
Important FactsType: Left & Right
Shaft Diameter: 8, 9, 10, 11, 12, 13, 14, 15mm
Driving End Diameter: 11.5mm for shaft diameters ≤ 11mm Same as shaft diameter for all other sizes
Length: 240 to 480mm (20mm increments)
Reaming: 1 to 1.5mm larger than the nail diameter
Proximal Screw Size: 5.0mm fully threaded
Distal Screw Size: 5.0mm fully threaded
Screw Hex Size: 3.5mm for all
End Caps GTN: Standard, +5, +10, +15mm
End Caps T2: Standard, +5, +10, +15mm
Internal Diameter: Shaft - 5.0mmDriving end - 8mm metric thread
Canulated Compression Screw:Standard (8mm metric thread)
0mm8mm
43mm
26.6mm
45mm
55mm
69.5mm
CompressionRange 10mm
0mm
4° Valgus Bend R=1.5m
Driving End
GTN End-Caps cannot be used with internal compression screw
T2 End-Caps used with cannulated compression screw
T2_BR_1_Rev1.indd 10 7/1/14 1:57 PM
T2 Supracondylar Nail (SCN)Required Instruments
Instruments: • T2 Basic Long Tray • T2 SCN Tray • Bixcut Modular Head Reamer Kit (diameter 9 to 18mm)a
Disposables - Sterile: Qty Description Cat No.
1 3 x 285 K-Wire (Entry) 1806-0050S 1 3 x 1000 Ball Tip Guide Wire 1806-0085S 1 Bixcut Mod Trinkle Shaft, 448mm 0227-3000S 1 4.2 x 340 Drill Bit (Distal & Proximal Guided) 1806-4260S 1 4.2 x 230 Drill Bit (Proximal Freehand) 1806-4290S 1 1.8 x 310 Condyle Screw K-Wire 0152-0218S 1 5.0 x 340 Drill Bit (For Condyle Screw) 1806-5020S
Notes:a. Optional: Full Bixcut Kit (diameter 6 to 22mm)
b. Optional: Bixcut with AO shaft, 448mm - Cat No: 0226-3000S
T2_BR_1_Rev1.indd 11 7/1/14 1:57 PM
Important FactsShaft Diameter: 9, 10, 11, 12, 13, 14mm
Driving End Diameter: 11.5mm for shaft diameters ≤ 11mm Same as shaft diameter for all other sizes
Length: Short Nail – 170 & 200mmLong Nail – 240 to 440mm (20mm increments)
Reaming: 1 to 1.5mm larger than the nail diameter
Proximal Screw Size: 5.0mm fully threaded
Distal Screw Size: 5.0mm fully threaded 5.0mm condyle screws
Screw Hex Size: 3.5mm for fully threaded6.3mm for condyle screws and nuts
End Caps: Standard (locks most distal screw)
Internal Diameter: Shaft - 5.0mmDriving end - 8mm metric thread
Driving End0mm6
14 21
32
42(4° A/P bend)
0mm
1520
40
R=2mLong Nail Only
Short Nailhas No Bow
Hole reference dimensions are the same for the Long and Short nails.
T2_BR_1_Rev1.indd 12 7/1/14 1:57 PM
T2 Recon Nail (Antegrade Mode) Required Instruments
Instruments: • T2 Basic Long Tray • T2 Recon Tray
• Bixcut Modular Head Reamer Kit (diameter 9 to 18 mm)a
Disposables - Sterile: Qty Description Cat No.
1 3.2 x 400 Recon K-Wire (Entry) 1806-3031S 1 3 x 1000 Ball Tip Guide Wire 1806-0085S 1 Bixcut Mod Trinkle Shaft, 448mmb 0227-3000S 1 4.2 x 250 Drill Bit (Proximal Guided First Cortex) 1806-8018S 1 4.2 x 340 Drill Bit (Proximal Guided) 1806-4260S 1 4.2 x 180 Drill Bit (Distal Freehand) 1806-4270S
Notes:a. Optional: Full Bixcut Kit (diameter 6 to 22mm)
b. Optional: Bixcut with AO shaft, 448mm – Cat No: 0226-3000S
T2_BR_1_Rev1.indd 13 7/1/14 1:57 PM
Important Facts (Antegrade Mode)
Type: Left & Right
Shaft Diameter: R2.0: 9, 11, 13, 15R1.5: 9, 10, 11, 12, 13, 15
Driving End Diameter: 13mm for shaft diameters 9-12mm15mm for shaft diameters 13 & 15mm
Length: R2.0: 280 to 480mmR1.5: 260 to 480mm(20 mm increments)
Reaming: 1.5 to 2.0mm larger than the nail diameter
Proximal Screw Size: 5.0mm fully threaded
Distal Screw Size: 5.0mm fully threaded
Screw Hex Size: 3.5mm for all
Set Screw: 8.0mm metric thread(Locks oblique screw)
End Caps: Standard, +5, +10, +15mm
Internal Diameter: Shaft - 5.0mmDriving end - 8mm metric thread
Driving End
0mm
70°
Set Screw, Antegrade
0mm
44
15
40
20
R= 2.0 or 1.5m
7° retroversion
4° Valgus Bend75
T2_BR_1_Rev1.indd 14 7/1/14 1:57 PM
T2 Recon Nail (Recon Mode) Required Instruments
Instruments: • T2 Basic Long Tray • T2 Recon Tray • Bixcut Modular Head Reamer Kit (diameter 9 to 18 mm)a
Disposables - Sterile: Qty Description Cat No.
2 3.2 x 400 Recon K-Wire (Entry & Lag Screws) 1806-3031S 1 3 x 1000 Ball Tip Guide Wire 1806-0085S 1 Bixcut Mod Trinkle Shaft, 448mmb 0227-3000S 1 Solid Step Drill (Lag Screws) 1806-3026S 1 4.2 x 180 Drill Bit (Distal Freehand) 1806-4270S
Notes:a. Optional: Full Bixcut Kit (diameter 6 to 22mm)
b. Optional: Bixcut with AO shaft, 448mm – Cat No: 0226-3000S
T2_BR_1_Rev1.indd 15 7/1/14 1:57 PM
Important Facts (Recon Mode)
Type: Left & Right
Shaft Diameter: R2.0: 9, 11, 13, 15R1.5: 9, 10, 11, 12, 13, 15
Driving End Diameter: 13mm for shaft diameters 9-12mm15mm for shaft diameters 13 & 15mm
Length: R2.0: 280 to 480mmR1.5: 260 to 480mm(20 mm increments)
Reaming: 1.5 to 2.0mm larger than the nail diameter
Proximal Screw Size: 6.5mm Lag Screws
Distal Screw Size: 5.0mm fully threaded
Screw Hex Size: 3.5mm for fully threaded screws5.0mm for Lag Screws
Set Screw: 8.0mm metric thread (locks most proximal lag screw)
End Caps: Standard, +5, +10, +15mm
Internal Diameter: Shaft - 5.0mmDriving end - 8mm metric thread
Driving End
0mm
4° Valgus Bend
Set Screw, Recon
26
10.5
17
125° CCD
0mm
15
40
20
2.0 or 1.5m
10° Anteversion
75
T2_BR_1_Rev1.indd 16 7/1/14 1:57 PM
T2 Humeral Nail (Antegrade & Retrograde) Required Instruments
Instruments: • T2 Basic Short Tray • T2 Humeral Tray • Full Bixcut Kit (diameter 6 to 22mm)
Disposables - Sterile: Qty Description Cat No.
1 3 x 285 K-Wire (Entry) 1806-0050S 1 2.5 x 800 Ball Tip Guide Wire 1806-0083S 1 Teflon Exchange Tubea 1806-0073S 1 2.2 x 800 Smooth Tip Guide Wire 1806-0093S 1 3.5 x 230 Drill Bit (Proximal & Distal)b 1806-3540S
For Internal Compression - Partially threaded screw is required for oblong hole. - Overdrill near cortex only with the drill below.
Qty Description Cat No.
1 4.0 x 180 Drill Bit 1806-4000S
Notes:a. With T2 PHN / HUMb. Optional: Drill for freehand locking: • (1) 3.5 x 130 Drill Bit – Cat No: 1806-3550S
T2_BR_1_Rev1.indd 17 7/1/14 1:57 PM
Important FactsShaft Diameter: 7, 8, 9mm
Driving End Diameter: 8mm for 7mm shaft diameter Same as shaft diameter for all other sizes
Length: 140 to 180mm (20mm increments)190 to 320mm (10mm increments)
Reaming: 1 to 1.5mm larger than the nail diameter
Proximal/Distal Screw Size: 4.0mm fully threaded1
Screw Hex Size: 3.5mm for all2.5mm for commpression screw only
End Caps: Standard, +5, +10, +15, +20, +25mm (all sizes lock screw in hole closest to driving end)
Internal Diameter: Shaft - 2.65mmDriving end - 6mm metric thread
Compression Screw: Advanced (6mm metric thread)
0mm
12
23
62Bend, 6°
CompressionRange 6mm
3036
48
28
18
10
0mm
Bend, 4°
Driving End
No Bow
T2_BR_1_Rev1.indd 18 7/1/14 1:57 PM
T2 Proximal Humeral Nail (PHN)Required InstrumentsInstruments: • T2 Basic Short Tray • T2 PHN Tray • Full Bixcut Kit
Disposables - Sterile: Qty Description Cat No.
1 3 x 285 K-Wire (Entry) 1806-0050S 1 2.5 x 800 Ball Tip Guide Wire 1806-0083S 1 Teflon Exchange Tube 1806-0073S 1 2.2 x 800 Smooth Tip Guide Wire 1806-0093S 1 3.5 x 130 Drill Bit (Distal free-hand)b 1806-3550S
Optional: Drills for Proximal screws in case of dense bone. Drill Near Cortex Only
Qty Description Cat No.
1 5.0 x 180 Drill Bit (Proximal) 1806-5010S
Notes:a. Distal guided drill only for short nail
b. Use with long nail only
T2_BR_1_Rev1.indd 19 7/1/14 1:57 PM
Important Facts Type: Left & Right
Shaft Diameter: 8mm
Driving End Diameter: 10mm
Length: Short Nail: 150mmLong Nail: 220 to 300mm (20mm increments)
Reaming: 1-1.5mm larger than the diameter of nails
Proximal Screw Size: 5.0mm fully threaded
Distal Screw Size: 4.0mm fully threaded
Screw Hex Size: 3.5mm for all
End Caps: Standard, +2 +4mm (all sizes lock screw in most proximal hole)
Internal Diameter: Shaft - 2.65mmDriving end - 6mm metric thread
Long Nail
95
101
0mm
62Bend,
6°
80
10°
9°
Short Nail
9.5
17
23
29.5
7.5
0mm
2113.5
28.5
36
Driving End
No BowLong & Short Nail
T2_BR_1_Rev1.indd 20 7/1/14 1:57 PM
T2 Knee Arthrodesis NailRequired InstrumentsInstruments: • T2 Basic Long Tray
• T2 Femoral Tray • Bixcut Modular Head Reamer Kit (diameter 9 to 18mm)
Disposables - Sterile: Qty Description Cat No.
1 3 x 285 K-Wire (Entry) 1806-0050S 2 3 x 1250 Ball Tip Guide Wireb 1806-1250S 1 Bixcut Mod Trinkle Shaft, 885mmb 0227-8885S 1 4.2 x 340 Drill Bit (Proximal) 1806-4260S 1 4.2 x 180 Drill Bit (Distal) 1806-4270S
For Internal Compression - Partially threaded screw is required for oblong hole. - Overdrill near cortex only with the drill below.
Qty Description Cat No.
1 5.0 x 230 Drill Bit 1806-5000S
Notes:a. Optional: Full Bixcut Kit (diameter 6 to 22mm)b. Optional: For separate reaming of Tibia and Femur use: Tibia: 3 x 800 Ball Tip Guide Wire – Cat No: 1806-0080S Femur: 3 x 1000 Ball Tip Guide Wire – Cat No: 1806-0085S Bixcut Mod Trinkle Shaft, 448mm – Cat No: 0227-3000S Optional: Bixcut with AO shaft, 448mm - Cat No: 0226-3000S
T2_BR_1_Rev1.indd 21 7/1/14 1:57 PM
Important FactsType: Left & Right
Shaft Diameter: 10, 11.5, and 13mm
Driving End Diameter: Same as shaft diameter
Length: 540 to 780mm (40mm increments)
Reaming: 1.5 to 2.0mm larger than the diameter of the nail
Proximal Screw Size: 5.0mm fully threaded1
Distal Screw Size: 5.0mm fully threaded
Screw Hex Size: 3.5mm for all
End Caps: Standard, +5, +10, +15, +20, +25, +30, +35mm (does not lock most proximal screw)
Internal Diameter: Shaft - 5.0mmDriving end - 8mm metric thread
Compression Screw: Standard, only 8mm compression screw(Cat. No: 1825-0000S)(all sizes have 8mm metric thread)
Do not use the most proximal hole on the Targeting device.
Driving End
0mm
0mm
35
45
60
2535
75
R=3m
Compression range 10mm
5° Bend (Valgus)
T2_BR_1_Rev1.indd 22 7/1/14 1:57 PM
T2 Ankle Arthrodesis NailRequired Instruments
Instruments: • T2 Basic Long Tray
• T2 Ankle Tray • Bixcut Modular Head Reamer Kit (diameter 9 to 18mm)
Disposables - Sterile: Qty Description Cat No.
1 3 x 285 K-Wire (Entry) 1806-0050S 1 3 x 800 Ball Tip Guide Wire 1806-0080S 1 Bixcut Mod Trinkle Shaft, 448mmc 0227-3000S 1 Teflon Exchange Tube 1806-0073S 1 3 x 800 Smooth Tip Guide Wire 1806-0090S 1 4.2 x 340 Drill Bit 1806-4260S 1 4.2 x 250 Drill Bit (Proximal Guided)b 1806-8018S
For Internal Compression - Partially threaded screw is required for oblong hole. - Overdrill near cortex only with the drill below.
Qty Description Cat No.
1 5.0 x 230 Drill Bit 1806-5000S
Notes:a. Optional: Full Bixcut Kit (diameter 6 to 22mm) b. For 300mm nail proximal free hand locking is required Use: 4.2 x 130 Drill Bit – Cat No: 1806-4280Sc. Optional: Bixcut with AO Shaft, 448mm – Cat. No: 0226-3000S
T2_BR_1_Rev1.indd 23 7/1/14 1:57 PM
Important FactsType: Left & Right
Shaft Diameter: 10, 11, and 12mm
Driving End Diameter: 12mm for all shaft diameters
Length: 150, 200 and 300mm
Reaming: 1 to 1.5mm larger than the diameter of the nail Proximal Screw Size: 5.0mm fully threaded
Distal Screw Size: 5.0mm fully threaded1
Screw Hex Size: 3.5mm for all
End Caps: Standard, +5, +10, +15mm (All sizes lock screw in most distal hole)
Internal Diameter: Shaft - 5.0mmDriving end - 8mm metric thread
Compression Screw: 8mm metric thread, cannulated2
(Cat. No: 1818-0001S)Must be pre-loaded into nail prior to insertion
Ball tip Guide wire does not pass through compression screw
Driving End
No Bow
47
19.5
7.5
40
15
0mm
0 mm
5° valgus bend
Distal hole is10° P/M to A/L
InternalCompression Range 5mm
20
T2_BR_1_Rev1.indd 24 7/1/14 1:57 PM
T2 Kids Flexible Nail
Instruments: T2 Kids Basic
Materials The T2 Flexible Nail is offered in two materials:
Titanium: Ti6Al4V Type II anodized withlaser-etched bands for easy nail diameter identification
Stainless Steel: 1.4441 (316LVM) with laser etched bands for easy nail diameter identification
Diameters Diameters: Ø1.5; Ø1.75; Ø2.0; Ø2.25mm with length 300mm
Diameters: Ø2.5; Ø3.0; Ø3.5; Ø4.0mm with length 450mm
Ø Nail = 0.4 x ØIM Canal (with some individual adaptations tolerated).
T2 Kids Optional Instrument Set available separately.
Pre-curved shaft portionIt can be bent back with the bending instrument, if required.
Nail Tip
Outercurve(convex)
Inner Curve(concave)
Tapered extremity
Curved Nail tip ornail tip curvature
ø N
ail
(d)
Tip
R = 4 x Nail ø
TipøNail
= 2.2
øNail = øIM canal x 0.4
Nail end (Driving end)
T2_BR_1_Rev1.indd 25 7/1/14 1:57 PM
325 Corporate Drive Mahwah, NJ 07430 t: 201 831 5000
www.stryker.com
A surgeon must always rely on his or her own professional clinical judgment when deciding whether to use a particular product when treating a particular patient. Stryker does not dispense medical advice and recommends that surgeons be trained in the use of any particular product before using it in surgery. The information presented is intended to demonstrate the breadth of Stryker product offerings. A surgeon must always refer to the package insert, product label and/or instructions for use before using any Stryker product. Products may not be available in all markets because product availability is subject to the regulatory and/or medical practices in individual markets. Please contact your Stryker representative if you have questions about the availability of Stryker products in your area.
Stryker Corporation or its divisions or other corporate affiliated entities own, use or have applied for the following trademarks or service marks: Stryker, T2. All other trademarks are trademarks of their respective owners or holders.
T2-BR-1 Rev. 1 06-2014
Copyright © 2014
T2_BR_1_Rev1.indd 26 7/1/14 1:57 PM
Recommended