SUBMITTAL: FLANGE JOINT CLASS 250 PRODUCT · FLANGES: ANSI Class 250 per ASME B16.1 and ANSI/AWWA...

28U‐B ‐ ANSI/AWWA C110/A21.10 Class 250 Flange Joint Full Body

Ductile Iron Fittings Revised 4/2018

DOMESTIC NON‐DOMESTIC

Anniston: 1501 W 17th St. ● Anniston, AL 36201 ● (800) 226‐7601 Elmer: 701 Kenyon Ave.● Elmer, New Jersey 03318 Corona: 1001 El Camino Ave. ● Corona, CA 92879 ● (866) 527‐8471 New Lenox: 2200 West Haven● New Lenox, IL 60451 Tyler: 11910 CR 492 ● Tyler, Texas 75706 ● (800) 527‐8478 Portland: 15670 N. Lombard St. ● Portland, OR 97203 Dallas: 1201 Ave. S. Suite100 ● Grande Prairie, TX 75050 Oxford: 1800 Greenbrier Dear Road ●Anniston, AL 36207

SUBMITTAL: C110 FLANGE JOINT CLASS 250 PRODUCT (Current revisions for the noted Standards apply)

SIZES: 2” ‐ 48”

STANDARDS: ANSI/AWWA C110/A21.10, NFPA 13/24, ASME B16.1

MATERIAL: Cast of ASTM A536 qualified ductile iron. Date code is cast on and required for traceability.

PRESSURE RATING: *Flanged fittings *2” – 48” rated at 250 psi. *Note: With rubber annular ring flange gasket, 2” – 24” flanged fittings can be rated at 350 psi.

DEFLECTION: Deflection is “not” recommended for flange joint due to the rigidity of the joint.

NSF‐61 & NSF372: Meets all requirements including Annex G, Tyler Union’s Underwriters Laboratory listing MH16439.

COATING: Asphaltic or Primer per ANSI/AWWA C104/A21.4, Standard primer is Tnemec Pota Pox N140‐1211. Contact Tyler Union for additional coating options.

CEMENT LINING: Per ANSI/AWWA C104/A21.4, with double cement lining available upon request. EPOXY COATING: Fusion bonded epoxy per ANSI/AWWA C116/A21.16. Additional coatings available upon request. BARE FITTINGS: Available upon request.

FLANGES: ANSI Class 250 per ASME B16.1 and ANSI/AWWA C111/A21.11. Bolt holes shall straddle the center line NOTE: Class 250 ASME B16.1 are not compatible with Class 125 Flanges NOTE: Class 250 ASME B16.1 fittings are available upon request.

FASTNERS: High strength low alloy weathering steel per ANSI/AWWA C111/A21.11 and ASTM A242 INSTALLATION: Install per AWWA C600/C651 using pipe conforming to ANSI/AWWA C151/A21.51.

SUBMITTAL: FLANGE JOINT CLASS 250 PRODUCT · FLANGES: ANSI Class 250 per ASME B16.1 and ANSI/AWWA...

Documents

SUBMITTAL: FLANGE JOINT CLASS 125 PRODUCT · · 2018-04-20NOTE: Class 250 ASME B16.1 fittings are available upon request. ... Microsoft Word - 28U FE C110 Sub 07012016.docx Author:

· 1 day ago · RESMI.S SOORYA A.S AKISHNA.P.S AMRUTHA RAJ.B BINCY.E.JOHNSON llnd Class - (250-299) Illrd Class - (175-249) 1st Class 1st Class 1st Class 1st Class 1st Class 1st

SKV Series SelfSensing Vertical Close Coupled Pumps€¦ · Casing Temperature250 °F (120 C) CF * In accordance with ANSI Standard B16.1 Class 125 N/A Cast Iron ASTM ... MOTOR DESIGN

brands you trust. - State Supplythe ASME Standard B16.1 for Classes 125 and 250 Cast Iron Flanges. Face-to-face dimensions comply with ASME Standard B16.10. DESIGN: GLOBE AND ANGLE

ABC B16.1 Cast Iron Pipe Flanges

Bus. 250 Spring 2014 - 4th Class Version B

CLASS H, K & R€¦ · CLASS H, K & R 250 & 600 Volt Fuse Blocks 250 & 600V Class H, K & R Fuse Blocks Mersen Class H, K and R fuse blocks accommodate all Class H, K and R 250 and

I I I · Flange Fittings – Class 125 and 250 Specifications • Fitting dimensions manufactured in accordance to ASME B16.1 and AWWA C110/A21.10. • Made from Ductile Cast Iron

CLASS 125/ CLASS 250/ PN16/PN25/JIS 10K/JIS 16K Wafer

Gray Iron Pipe Flanges and Flanged Fittings · 2020-01-02 · ASME B16.1-2015 (Revision of ASME B16.1-2010) Gray Iron Pipe Flanges and Flanged Fittings Classes 25, 125, and 250 AN

ACO Line Drainage€¦ · Installation 7 Technical Data ACO DRAIN N100 Load class B 125 8 Load class C 250 8 ACO DRAIN V100/M100D/XD100 Load class C 250 9 Load class D 400 9 ACO DRAIN

ASME-ANSI B16.1-1989.pdf

DUCTILE IRON FLANGED FITTINGS - McWane · DUCTILE IRON FLANGED FITTINGS ANSI/AWWA-C110/A21.10 Standard and ANSI B16.1 Class 125 Standard SPECIFICATIONS Flanged fittings shown on …

RESILIENT WEDGE GATE VALVE - American USA...ANSI/AWWA C110/A21.10 (ASME B16.1 Class 125). 2. Standard internal and external coating is fusion-bonded epoxy and meets requirements of

ASME B16.1-2010_Gray Iron Pipe Flanges and Flanged Fittings Classes 25, 125, And 250

SUBMITTAL: FLANGE JOINT CLASS 125 PRODUCT · 2018-04-20 · FLANGES: ANSI Class 125 per ASME B16.1 and ANSI/AWWA C111/A21.11. Bolt holes shall straddle the center line NOTE: Class

UWP Flange Fitting Catalog B16.1 (9-19) Listed... · 2021. 1. 20. · Ductile Cast Iron, ASTM A536, Grey Cast Iron, ASTM A126 Flange Fittings – Class 125/150 and 250 Speciﬁ cations

COMM 250 Speech Codes Theory Presentation -- Revision 3 for Class

INCREASING SWING FLAP VALVES CHECK VALVES · 3”–120” — ASME B16.1 Class 125 flanged end connections 54” — ASME B16.1 Class 250 flanged end connections available 3”–108”

Bus 250. Spring 2014 - 5th Class