View
17
Download
0
Category
Preview:
Citation preview
ANALOG COMMUNICATION SYSTEMS LAB
II/IV B. TECH., II SEMESTER
STUDENT OBSERVATION MANUAL
DEPARTMENT
OF
ELECTRONICS & COMMUNICATION ENGINEERING
VEMU INSTITUTE OF TECHNOLOGY Tirupati - Chittoor Highway Road, P. Kothakota, Chittoor- 517 112.
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY ANANTAPUR
VEMU INSTITUTE OF TECHNOLOGY
DEPT. OF ELECTRONICS AND COMMUNICATION ENGINEERING
Vision of the institute
To be a premier institute for professional education producing dynamic and vibrant force of
technocrat with competent skills, innovative ideas and leadership qualities to serve the society
with ethical and benevolent approach.
Mission of the institute
Mission_1: To create a learning environment with state-of-the art infrastructure, well equipped
laboratories, research facilities and qualified senior faculty to impart high quality technical
education.
Mission_2: To facilitate the learners to foster innovative ideas, inculcate competent research and
consultancy skills through Industry-Institute Interaction.
Mission_3: To develop hard work, honesty, leadership qualities and sense of direction in rural
youth by providing value based education.
Vision of the Department
To become a centre of excellence in the field of Electronics and Communication Engineering and
produce graduates with Technical Skills, Research & Consultancy Competencies, Life-long
Learning and Professional Ethics to meet the challenges of the Industry and Society.
Mission of the Department
Mission_1: To enrich Technical Skills of students through Effective Teaching and Learning
practices for exchange of ideas and dissemination of knowledge.
Mission_2: To enable the students with research and consultancy skill sets through state-of-the
art laboratories, industry interaction and training on core & multidisciplinary technologies.
Mission_3: To develop and instill creative thinking, Life-long learning, leadership qualities,
Professional Ethics and social responsibilities among students by providing value based
education.
Programme Educational Objectives ( PEOs)
PEO_1: To prepare the graduates to be able to plan, analyze and provide innovative ideas to
investigate complex engineering problems of industry in the field of Electronics and
Communication Engineering using contemporary design and simulation tools.
PEO_2: To provide students with solid fundamentals in core and multidisciplinary domain for
successful implementation of engineering products and also to pursue higher studies.
PEO_3: To inculcate learners with professional and ethical attitude, effective communication
skills, teamwork skills, and an ability to relate engineering issues to broader social context at
work place.
Programme Outcome (POs)
PO_1: Engineering knowledge: Apply the knowledge of mathematics, science, engineering
fundamentals, and an engineering specialization to the solution of complex engineering problems.
PO_2: Problem analysis: Identify, formulate, review research literature, and analyze complex
engineering problems reaching substantiated conclusions using first principles of mathematics,
natural sciences, and engineering sciences.
PO_3: Design/development of solutions: Design solutions for complex engineering problems
and design system components or processes that meet the specified needs with appropriate
consideration for the public health and safety, and the cultural, societal, and environmental
considerations.
PO_4: Conduct investigations of complex problems: Use research-based knowledge and
research methods including design of experiments, analysis and interpretation of data, and
synthesis of the information to provide valid conclusions.
PO_5: Modern tool usage: Create, select, and apply appropriate techniques, resources, and
modern engineering and IT tools including prediction and modeling to complex engineering
activities with an understanding of the limitations.
PO_6: The engineer and society: Apply reasoning informed by the contextual knowledge to
assess societal, health, safety, legal and cultural issues and the consequent responsibilities relevant
to the professional engineering practice.
PO_7: Environment and sustainability: Understand the impact of the professional engineering
solutions in societal and environmental contexts, and demonstrate the knowledge of, and need for
sustainable development.
PO_8: Ethics: Apply ethical principles and commit to professional ethics and responsibilities and
norms of the engineering practice.
PO_9: Individual and team work: Function effectively as an individual, and as a member or
leader in diverse teams, and in multidisciplinary settings.
PO_10: Communication: Communicate effectively on complex engineering activities with the
engineering community and with society at large, such as, being able to comprehend and write
effective reports and design documentation, make effective presentations, and give and receive
clear instructions.
PO_11: Project management and finance: Demonstrate knowledge and understanding of the
engineering and management principles and apply these to one’s own work, as a member and
leader in a team, to manage projects and in multidisciplinary environments.
PO_12: Life-long learning: Recognize the need for, and have the preparation and ability to
engage in independent and life-long learning in the broadest context of technological change.
Programme Specific Outcome (PSOs)
PSO_1: Higher Education: Qualify in competitive examinations for pursuing higher education
by applying the fundamental concepts of Electronics and Communication Engineering domains
such as Analog & Digital Electronics, Signal Processing, Communication & Networking,
Embedded Systems, VLSI Design and Control Systems etc..
PSO_2: Employment: Get employed in allied industries through their proficiency in program
specific domain knowledge, specialized software packages and Computer programming or
become an entrepreneur.
(15A04407) ANALOG COMMUNICATION SYSTEMS LAB
B.Tech II-II Sem. (E.C.E.)
Course Outcomes:
C228.1: Analyze behavior of analog modulations systems in the time domain
C228.2: Analyze behavior of pulse modulations systems in the time domain
C228.3: Illustrate the characteristics of radio receiver and antenna measurements
List of Experiments: (All Experiments are to be conducted)
1. Amplitude modulation and demodulation.
2. Frequency modulation and demodulation.
3. a. Characteristics of Mixer.
b. Pre-emphasis & de-emphasis.
4. Pulse amplitude modulation & demodulation.
5. Pulse width modulation & demodulation
6. Pulse position modulation & demodulation.
7. Radio receiver measurements – sensitivity selectivity and fidelity. 8. Measurement of half power beam width (HPBW) and gain of a half wave dipole
Antenna.
9. Measurement of radiation pattern of a loop antenna in principal planes.
Equipment required for the Laboratory:
1. Regulated Power Supply equipments 0 – 30 V
2. CROs 0 – 20 M Hz.
3. Function Generators 0 – 3 M Hz
4. RF Signal Generators 0 – 1000 M Hz
5. Multimeters
6. Required electronic components (active and passive) for the design of experiments
from 1 - 7
7. Radio Receiver Demo kits or Trainers.
8. RF power meter frequency range 0 – 1000 MHz 9. Spectrum Analyzer
10. Dipole antennas (2 Nos.) 850 MHz – 1GHz
11. Loop antenna (1 no.) 850 MHz – 1GHz
VEMU INSTITUTE OF TECHNOLOGY::P.KOTHAKOTA NEAR PAKALA, CHITTOOR-517112
(Approved by AICTE, New Delhi & Affiliated to JNTUA, Anantapuramu) Department of Electronics &Communication Engineering
LIST OF EXPERIMENTS TO BE CONDUCTED
PART-A
List of Experiments: (All Experiments are to be conducted)
1. Amplitude modulation and demodulation.
2. Frequency modulation and demodulation.
3. a. Characteristics of Mixer.
b. Pre-emphasis & de-emphasis.
4. Pulse amplitude modulation & demodulation.
5. Pulse width modulation & demodulation
6. Pulse position modulation & demodulation.
7. Radio receiver measurements – sensitivity selectivity and fidelity.
8. Measurement of half power beam width (HPBW) and gain of a half wave
dipole Antenna.
9. Measurement of radiation pattern of a loop antenna in principal planes.
PART-B
ADVANCED EXPERIMENTS
1. Digital Phase Detector.
2. Balanced modulator and synchronous detector.
CONTENTS
S.NO. NAME OF THE EXPERIMENT PAGE
NO
1. AMPLITUDE MODULATION & DEMODULATION 1-5
2. FREQUENCY MODULATION & DEMODULATION 6-9
3(a) CHARACTERISTICS OF MIXER 10-13
3(b) PRE-EMPHASIS & DE-EMPHASIS 14-17
4. PULSE AMPLITUDE MODULATION AND DEMODULATION 18-21
5. PULSE WIDTH MODULATION AND DEMODULATION 22-25
6. PULSE POSITION MODULATION & DEMODULATION 26-29
7. RADIO RECEIVER MEASUREMENTS – SENSITIVITY,
SELECTIVITY AND FIDELITY
30-35
8. MEASUREMENT OF HALF POWER BEAM WIDTH (HPBW)
AND GAIN OF A HALF WAVE DIPOLE ANTENNA
36-39
9. MEASUREMENT OF RADIATION PATTERN OF A LOOP
ANTENNA IN PRINCIPLE PLANES
40-43
ADVANCED EXPERIMENTS
10. DIGITAL PHASE DETECTOR 44-46
11. BALANCED MODULATOR & SYNCHRONOUS DETECTOR 47-50
DOS & DONTS IN LABORATORY
1. While entering the Laboratory, the students should follow the dress code
(Wear shoes, White Apron & Female students should tie their hair back).
2. The students should bring their observation note book, practical manual,
record note book, calculator, necessary stationary items and graph sheets if
any for the lab classes without which the students will not be allowed for
doing the practical.
3. All the equipments and components should be handled with utmost care. Any
breakage/damage will be charged.
4. If any damage/breakage is noticed, it should be reported to the instructor
immediately.
5. If a student notices any short circuits, improper wiring and unusual smells
immediately the same thing is to be brought to the notice of technician/lab in
charge.
6. At the end of practical class the apparatus should be returned to the lab
technician and take back the indent slip.
7. Each experiment after completion should be written in the observation note
book and should be corrected by the lab in charge on the same day of the
practical class.
8. Each experiment should be written in the record note book only after getting
signature from the lab in charge in the observation note book.
9. Record should be submitted in the successive lab session after completion of
the experiment.
10. 100% attendance should be maintained for the practical classes.
PRECAUTIONS
1. Avoid loose connections.
2. Make sure that the connections are correct.
3. Take readings without parallax error.
4. Do not apply stress on the components.
5. Do not use the components beyond their specifications.
SCHEME OF EVALUVATION
S NO
DATE
NAME OF EXPERIMENT
MARKS AWARDED
Sign. Obser.
(10M)
Viva voce
(10M)
Total
(20M)
1 Amplitude Modulation & Demodulation
2 Frequency Modulation & Demodulation
3(a) Characteristics of Mixer
3(b) Pre-Emphasis & De-Emphasis
4 Pulse Amplitude Modulation and
Demodulation
5 Pulse Width Modulation and Demodulation
6 Pulse Position Modulation & Demodulation
7 Radio Receiver Measurements –
Sensitivity, Selectivity and Fidelity
8 Measurement Of Half Power Beam
Width (HPBW) and Gain of A Half
Wave Dipole Antenna
9 Measurement of Radiation Pattern of A
Loop Antenna in Principle Planes
10 Sampling Theorem Verification
ADVANCED EXPERIMENTS
1. Digital Phase Detector
2. Balanced Modulator and Synchronous
Detector
Signature of Lab In-charge
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 1
3. CIRCUIT DIAGRAM:
1. AMPLITUDE MODULATION & DEMODULATION
Aim: To generate amplitude modulated wave and determine the percentage modulation. To ge
nerate demodulated wave using envelope detector and plot the graph.
Apparatus Required:
1. Amplitude Modulation and Demodulation Trainer
2. Function Generator
3. Oscilloscope
4. Connecting Wires
5. Probes
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 2
1. AIM: To generate Amplitude modulated signal and determine the modulation index
2. APPARATUS REQUIRED:
1. Amplitude Modulation and Demodulation Trainer kit
2. Oscilloscope (osc-503; 30MHz))
4. Connecting Wires
5. BNC Probes
4. CIRCUIT OPERATION: Modulation is defined as the process of changing the characteristics of a
high frequency carrier signal in accordance with a low frequency message signal. The base band
signal is referred to as the modulating signal or message signal and the output of the modulation
process is called as the modulation signal. Amplitude modulation is defined as the process of
changing the amplitude of the carrier signal in accordance with the base band signal.
The envelope of the modulating wave has the same shape as the base band signal provided the
following two requirements are satisfied
(1). the carrier frequency fc must be much greater than the highest frequency components fm of
the message signal m (t) i.e. fc >> fm
(2) The modulation index must be less than unity. if the modulation index is greater than unity,
the carrier wave becomes over modulated
5. PROCEDURE:
1. As the circuit is already wired, the circuit has to be traced according to circuit diagram.
2. Connect the trainer to the main and switch on the power supply.
3. Measure the output voltage of the regulated power supply circuit +_ 12 V
4. Observe the output of RF and AF signal generator using CRO and note the RF voltage
approximately
300 Vp-p of 1 MHz frequency and AF voltage as 10 Vp-p of 2 KHz frequency
Modulation: 1. Now connect RF and AF signals to the respective input of modulator as shown in figure.
2. Initially check both the signals at zero levels
3. Connect one of the input of oscillator to modulator output and other input to AC signal
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 3
Calculations:
Adjust RF signal amplitude of AF signal and observe the amplitude modulated wave at output.
Note the percentage modulation for different values of signal
Percentage modulation = B-A/B+A*100
B=Minimum amplitude
A=Maximum amplitude
Observe 100% amplitude modulation and over modulation by varying amplitude of AF signal.
Demodulation:
1. Now connect the modulator output to the demodulator input as shown in figure
2. Observe the demodulated signal at output of demodulator at approximately 50% modulation
using oscilloscope.
3. Compare it with the original AF signal.
4. If the detected signal is same as the AF signal applied then there is no information is lost in the
process of modulation.
5. If AM wave is to be observed of differ external signal generator to the modulator and observe
the amplitude modulated wave at different frequencies.
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 4
6. EXPECTED WAVE FORMS:
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 5
7. RESULT:
AF INPUT:
Amplitude____________ VP-P & Frequency _______________KHz.
RF INPUT:
Amplitude____________ VP-P & Frequency _______________KHz.
MODULATION INDEX:
Case I: In Under modulation ma=_________________
Case II: In over modulation ma= __________________
8. CONCLUSIONS:
1. Amplitude of the carrier is varied in accordance with the instantaneous values of the modulating
signal.
2. The modulating signal can be recovered faithfully when carrier is either under or critically
modulated.
3. In the case of envelope detractor, the detection of modulating signal mainly depends on Resistor,
Capacitor & Modulation index.
9. VIVA QUESTIONS:
1. Define modulation and write need for modulation.
2. Write the expression for AM signal in the case of single tone, multi tone & band of frequencies?
3. Draw the spectrum of the AM signal in the case of single tone, multi tone & band of frequencies?
4. Write the power and current relation in AM signal?
5. What is BW and power efficiency of AM signal?
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 6
3. CIRCUIT DIAGRAM:
FM modulator:
FM demodulator:
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 7
2. FREQUENCY MODULATION & DEMODULATION
1. AIM: 1.To generate frequency modulated signal and determine the modulation index and
bandwidth for various values of amplitude and frequency of modulating signal.
2. To demodulate a Frequency Modulated signal using FM detector.
2. APPARATUS REQUIRED:
1. Physitech Frequency Modulation and Demodulation Trainer (phy-138)
2. Function Generator (phy-103m, 20 to 20MHz)
3. Oscilloscope (osc-503; 30MHz))
4. Connecting Wires
5. BNC Probes
4. CIRCUIT OPERATION:
Frequency modulation:
The process, in which the frequency of the carrier is varied in accordance with the instantaneous
amplitude of the modulating signal, is called "Frequency Modulation".
S(t) = Ac cos (wct +ө(t))
Where ө(t) = km ᶴ m(t) dt Km is the frequency sensitivity
MODULATION INDEX:
In FM modulation index is the ratio of frequency deviation (fd) to modulating frequency (fm).
It is denoted by m or β
Β = FD / FM
5. PROCEDURE:
1. Switch on the FM experimental board.
2. Connect Oscilloscope to the FM O/P and observe that carrier frequency at that point without
any A.F. input.
3. Connect around 3 KHz to 7 KHz sine wave (A.F. signal) with 2.4 V AF signal to the input of
the frequency modulator (At AF input).
4. Now observe the frequency modulation output on the 1st channel of on CRO and
Adjust the amplitude of the AF signal to get clear frequency modulated wave form.
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 8
6. MODEL WAVEFORMS:
5. Vary the modulating frequency (A.F Signal) and amplitude and observe the effects on the
modulated waveform.
6. Connect the FM o/p to the FM i/p of De-modulator.
7. Vary the potentiometer provided in the demodulator section.
8. Observe the output at demodulation o/p on second channel of CRO.
9. Draw the demodulated wave form
7. RESULT:
AF INPUT:
Amplitude____________ VP-P & Frequency _______________KHz.
RF INPUT:
Amplitude____________ VP-P & Frequency _______________KHz.
8. CONCLUSIONS:
1. Frequency of the carrier signal is varied in accordance with the message signal.
2. Modulation index in WBFM is greater than 1.
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 9
9. VIVA QUESTIONS:
1. Write the expression for FM signal in the case of single tone, multi tone & band of frequencies?
2. Draw the line spectrum of FM signal the case of single tone.
3. Define frequency deviation and write the Carlson formula.
4. Compare NBFM and WBFM.
5. Compare AM and FM.
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 10
3. CIRCUIT DIAGRAM:
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 11
3(a). CHARACTERISTICS OF MIXER
1. AIM: To observe the characteristics of a Frequency Mixer and to measure its conversion gain.
2. APPARATUS REQUIRED:
1. Physitech Frequency mixer trainer kit.
2. Function generator - (2)
3. C R O
4. B N C Probes
5. Connecting wires
4. CIRCUIT OPERATION:
A mixer is a non linear circuit with two input signals and one output signal. The output signal
is a distorted combination of the two input signals. Let the two input frequencies, given be F x and
because of non linear distortion, the output signal contains signal frequencies and their harmonics. In
addition to the harmonics, a frequency signal with frequency = (Fx-Fy) and also appear across output
terminals.
A Mixer circuit finds its application in a super heterodyne receiver in converting a RF signal
into an IF signal with help of a local oscillator. If RF signal frequency RF is 1000 KHz, by choosing
local oscillator frequency to 1455KHZ the difference frequency becomes 455 KHz, which is the
intermediate frequency for radio receiver. Other frequencies such as 1455 kHz, 1000 kHz and 2455
kHz can be filtered out with help of low pass filter. But for getting the clear output without distortion
low frequencies in the range of 85 kHz -115 kHz.
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 12
5. MODEL WAVEFORMS:
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 13
6. Procedure:
1. Connect the circuit as shown in the circuit diagram.
2. Apply 99 kHz signal to the base of the transistor and 100 kHz, signal to the emitter of the
transistor.
3. Observe a sinusoidal signal with 1kHz frequency across output terminals
4. Vary Base signal frequency and note down O/P amplitude. The output reaches to a Maximum
value at a particular frequency.
Calculate conversion gain.
Conversion gain = (O/P Voltage)/ (Base signal voltage)
5. Plot conversion for gain and base signal frequency.
7. RESULT:
INPUT 1
AMPLITUDE_______________V P-P& FREQUENCY______________KHz
INPUT 2
AMPLITUDE_______________ V P-P &FREQUENCY______________ KHz
MIXER OUTPUT:
AMPLITUDE_______________ V P-P &FREQUENCY______________ KHz
8.CONCLUSIONS:
1.Mixer generates sum or difference frequencies
2.It can be used in heterodyne receivers.
9. VIVA QUESTIONS:
1. What is need of mixer in heterodyne receivers?
2. What is linear and non linear operation in mixer?
3. How the sum and difference frequencies are generated using mixer circuit?
4. what is the need of filter in mixer circuit?
5.which type of filters are used in mixer?
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 14
3. CIRCUIT DIAGRAMS:
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 15
3(b). PRE-EMPHASIS & DE-EMPHASIS
1. AIM:
A) To observe the effects of pre-emphasis on given input signal.
B) To observe the effects of De-emphasis on given input signal.
2. APPARATUS REQUIRED:
1. Resistors (10 K, 33K,1K)-----Each one
2. Capacitors (10F, 0.1-F)
3. Transistor BC547
4 Function generators---------------------- 01
5. CRO-----------------------------------------01
6. Connecting Wires
7. Connecting wires.
4. CIRCUIT OPERATION:
The noise has an effect on the higher modulating frequencies than on the lower ones. Thus, if
the higher frequencies were artificially boosted at the transmitter and correspondingly cut at the
receiver, an improvement in noise immunity could be expected, thereby increasing the SNR ratio.
This boosting of the higher modulating frequencies at the transmitter is known as pre-emphasis and
the compensation at the receiver is called de-emphasis.
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 16
5. Tabular column: Pre-emphasis:
De-emphasis:
S.NO
Frequency
(KHz)
Input voltage
Vin (V)
Output voltage Vo
(V)
Gain (dB)= Vin/ Vo
20 log Vin/ Vo
1.
2.
3.
4.
5.
6.
7.
8.
S.NO
Frequency
(KHz)
Input voltage
Vin (V)
Output voltage Vo
(V)
Gain (dB)= Vin/ Vo
20 log Vin/ Vo
1.
2.
3.
4.
5.
6.
7.
8.
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 17
6. Procedure:
1. Study theory of operation thoroughly
2. Connect the trainer to mains and switch on the power supply
3. Measure the output of required power supply 12 V
4. Observe the output of AF Generator using frequency range of 0.66 Vp-p provided to select the
frequency range
5. Connect the AF signal to the required amplitude level
6. Adjust the AF signal to required amplitude level
7. Plot the graph between frequency output voltage
8. Plot the graph and note the frequency at which the output voltage is 70.7% of input voltage and
compare with theoretical frequency
9. Repeat the steps from 5 to 10 for the de-emphasis network
10. Theoretical frequency is given by 1/ 2πRC
8. RESULT:
Time Constant of Pre-Emphasis & De-Emphasis τ = ___________Sec
Cut off frequency of Pre-Emphasis & De-Emphasis fc = _________KHz
9.CONCLUSION:
It is used to imporove signal to noise ratio at audio frequency range in FM system.
10. VIVA QUESTIONS:
1. What is need of pre emphasis and de emphasis in FM system?
2. What is time constant of pre emphasis and de emphasis in audio applications?
3. Pre emphasis and De emphasis in are not used in AM system Why?
4. What are the cutoff frequencies of pre emphasis and de emphasis?
5. Write the transfer function pre emphasis and de emphasis?
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 18
3. CIRCUIT DIAGRAM:
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 19
4. PULSE AMPLITUDE MODULATION AND DEMODULATION
1. AIM: To generate the Pulse Amplitude modulated signal and demodulated signals.
2. APPARATUS REQUIRED:
1. Pulse amplitude modulation trainer.
2. Signal generator
3. CRO
4. BNC probes, CONNECTING WIRES.
4. Circuit Operation:
PAM is the simplest form of the data modulation. The amplitude of uniformly spaced
pulses is varied in proportion to the corresponding sample values of a continuous message m(t).A
PAM waveform consists of a sequence of list-topped pulses. The amplitude of each pulse corresponds
to the value of the message signal x(t) at the leading edge of the pulse.
The pulse amplitude modulation is the process in which the amplitude of regularity spaced
rectangular pulses vary with the instantaneous sample values of a continuous message signal in a one-
one fashion.
PAM is of two types:
1. Double polarity PAM - This is the PAM wave which consists of both positive and Negative
pulses.
2. Single polarity PAM - This consists of PAM wave of only either negative or positive pulses. In
this the fixed dc level added to the signal to ensure single polarity signal.
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 20
5. MODEL WAVEFORMS:
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 21
6. PROCEDURE:
1. Refer the block diagram and carryout the connections and switch settings.
2. Connect the power supply with proper polarity to the kit DCL-08 and switch it on.
3. Select 16 KHz sampling frequencies by jumper JP1.
4. Connect the 1 KHz, 2Vp-p sine wave signal generated on board to PAM IN POST.
5. Observe the amplitude pulse modulation output at PAM OUT POST.
6. Short the following posts with connecting chords provided as shown in block diagram
PAM OUT and PAM IN,PAM OUT and FIN IN
7. Keep the amplifier gain control potentiometer is to be maximum completely clockwise.
8. Observe the pulse amplitude demodulated signal at FIL OUT, which is same as the input signal.
9. Repeat the experiment for different input signals and sampling frequencies.
7 . RESULT:
Message Signal:
Amplitude_______________V P-P & Frequency______________KHz
Carrier Signal:
Amplitude_______________ V P-P & Frequency______________ KHz
PAM Signal:
Amplitude_______________ V P-P & Frequency______________ KHz
Demodulated Signal:
Amplitude_______________ V P-P & Frequency______________ KHz
8. CONCLUSIONS:
1. Amplitude of the discrete signal is varied in accordance with the message signal.
2. PAM can be used in PCM
9. VIVA QUESTIONS:
1. What are different sampling techniques are used to generate PAM signal?
2. What is the BW of PAM signal?
3. What is Aperture affect in PAM?
4. What is the minimum sampling frequency required to generate PAM?
5. What are the applications of PAM?
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 22
3. CIRCUIT DIAGRAM:
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 23
5. PULSE WIDTH MODULATION AND DEMODULATION
1. AIM: To generate the pulse width modulated and demodulated signals
2. APPARATUS REQUIRED:
1. Pulse width modulation and Demodulation Trainer.
2. CRO
3. BNC probes and Connecting Wires
4. CIRCUIT OPERATION:
In PWM, the samples of the message signal are used to vary the duration of the individual
pulses. Width may be varied by varying the time of occurrence of leading edge, the trailing edge or
both the edges of the pulse in accordance with modulating wave. It is also called Pulse Duration
Modulation.
Pulse Width Modulation
PWM controls the variation of duty cycle of square wave (with fundamental frequency )
according to the input modulating signal .Here the amplitude variation of the modulation signal is
reflected in the ON period variation of square wave. Hence, it is a technique of V to T conversion.
Pulse Width Demodulation
The input signal is demodulated, so the ON time of the signal is changing according to the
modulating signal .In this demodulation technique during ON time of PWM signal one counter is
enabled .At the end of ON time, counter gives a particular count, which directly corresponds to the
amplitude of input signal. Then this count is fed to DAC. The output of DAC corresponds to the
amplitude of the input signal. Thus train of varying pulse widths gives varying count values and
accordingly DAC give outputs, which is directly proportional to amplitude of input signal. This is
then filtered to get original signal .Thus at the output we get the original modulating signal extracted
from PWM wave.
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 24
5. MODEL WAVEFORMS:
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 25
6. PROCEDURE:
1. Switch on pulse width modulation and Demodulation trainer
2. Observe the clock generator output and modulating signal output
3. Connect the Clock output to the clock input terminal of PWM modulation.
Observe the same clock on channel of a dual trace CRO.
4. Trigger the CRO with respect to CH1
5. Apply the available DC voltage of 8V to 12 V from any external RPS
6. Observe the PWM output on CH2.
7. If we observe the modulating signal is given to the observe how the PWM
signal are varying for AC modulating signal.
8. In this case we have to trigger the CRO with respect to modulating voltage.
8. RESULT:
Message Signal:
Amplitude_______________V P-P & Frequency______________KHz
Carrier Signal:
Amplitude_______________ V P-P & Frequency______________ KHz
PWM Signal:
Amplitude_______________ V P-P
Demodulated Signal:
Amplitude_______________ V P-P & Frequency______________ KHz
9. CONCLUSIONS:
1. Width of the discrete signal is varied in accordance with the message signal.
2. PWM can be used to control the speed of the electric motor.
10. VIVA QUESTIONS:
1. What are different techniques to generate PWM?
2. What is the difference between discrete and continuous wave modulation?
3. What is the minimum sampling frequency of PWM?
4. Compare PAM, PPM &PWM.
5. What are the applications of PWM?
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 26
3. CIRCUIT DIAGRAM:
Pulse Position Modulation -(PPM)-Modulation :
Pulse Position Modulation (PPM)-De Modulation :
PPM Input
AF Input
Clk Input
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 27
6. PULSE POSITION MODULATION & DEMODULATION
1. AIM: To generate pulse position modulation and demodulation signals and to study the effect of
amplitude of the modulating signal on output.
2. APPARATUS REQUIRED:
1. Pulse position modulation and demodulation trainer.
2. CRO
3. BNC probes and Connecting Wires
4. CIRCUIT OPERATION:
In Pulse Position Modulation, both the pulse amplitude and pulse duration are held constant but
the position of the pulse is varied in proportional to the sampled values of the message signal. Pulse
time modulation is a class of signaling technique that encodes the sample values of an analog signal
on to the time axis of a digital signal and it is analogous to angle modulation techniques. The two
main types PTM are PWM and PPM. In PPM the analog sample value determines the position of a
narrow pulse relative to the clocking time. In PPM rise time of pulse decides the channel bandwidth.
It has low noise interference.
Modulating a digital signal's pulse position is straightforward. Each delay between pulses is
represented by a zero or a one. A small delay is represented by zero; a long delay is represented by
one. The duration of delay varies according to the system's requirements. For example, in a Sony
infrared remote protocol that uses PPM, a short delay of 1.2 meters per second is represented by zero,
and a longer delay of 1.8 meters per second is represented by one.PPM is very sensitive to external
interferences. Although interference is usually impossible to detect, it can cause complete data
corruption. Therefore, PPM is not used in cable communications, which are subject to
electromagnetic interference. PPM is, however, used in fiber optic cables, which are not subject to
interference.
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 28
5. OUTPUT WAVEFORMS:
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 29
6. PROCEDURE:
1. Switch on PPM modulator and demodulator trainer.
2. Connect the clock input to the Pin 2 of IC 555.
3. Connect the AF output to the pin 5 of IC 555.
4. Observe the PPM Output at pin 3 of second IC 555 on CRO.
5. Connect the PPM Output to the PPM Input of PPM demodulation.
6. Observe the demodulated Output on CRO.
7. RESULT:
Message Signal:
Amplitude_______________V P-P & Frequency______________KHz
Carrier Signal:
Amplitude_______________ V P-P & Frequency______________ KHz
PPM Signal:
Amplitude_______________ V P-P
Demodulated Signal:
Amplitude_______________ V P-P & Frequency______________ KHz
8. CONCLUSIONS:
1. Position of the discrete signal is varied in accordance with the message signal.
2. PPM can be obtained from PWM.
9. VIVA QUESTIONS:
1. Define PPM?
2. What is the minimum sampling frequency of PPM?
3. What is the difference between discrete and continuous wave modulation?
4. What are the applications of PPM?
5. What are the merits & demerits of PTM over PAM?
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 30
3. CIRCUIT DIAGRAM:
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 31
7. RADIO RECEIVER MEASUREMENTS – SENSITIVITY, SELECTIVITY AND FIDELITY
1. AIM: To study the Sensitivity, Selectivity and Fidelity of a radio receiver.
2. EQUIPMENT REQUIRED:
1. Trainer Kit
2. CRO
3. Probes
4. Patch cards
4. CIRCUIT OPERATION:
Sensitivity:
The sensitivity of a receiver is its ability to amplify weak signals. The sensitivity of a receiver is the
minimum voltage required at the input of the receiver to produce the original signal.
It is often defined in terms of the voltage that must be applied to the receiver input terminals to give a
standard output power, measured at the output terminal.
For an AM broadcast receivers, several relevant quantities have been standardized. The most
important factors determining sensitivity of a receiver is the Gain of the receiver.
Selectivity:
A parallel tuned circuit has its greatest impendence at resonance and decreased at higher and lower
frequencies. If a tuned circuit is induced in the circuit design of an amplifier, it results in the
amplifiers, which offers more gain at the frequency of resonance and reduced amplification above
and below this frequency. This is called selectivity.
The radio receiver is tuned to a frequency of 820 KHz and at this frequency the amplifer
provides a gain of five.
5. PROCEDURE:
Sensitivity:
1. Refer to the figure and carry out the following connections
2. Connect the output of function generator section (ACL-AM) outpost to the input of balance
modulator (ACL-AM) signal post.
3. Connect the output of VCO (ACL-AM) outpost to the input of balance modulator (ACL-AM)
carrier in post.
4. Connect the power supply with proper polarity to the kit ACL-AM & ACC-AP, while
connecting. Ensure that power supply is OFF.
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 32
6. TABULAR COLUMN:
For sensitivity:
Carrier
Freq.(KHz) VCO
600 700 800 900 1000 1100 1200 1300
Local OSC.
Freq.(KHz) 1050 1150 1250 1350 1450 1550 1650 1750
Output of
Mixer(V)
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 33
Function generator:
Sine wave about 0.5 VP-P Frequency about 1KHz
VCO level about 2 VP-P Frequency about 600 KHz
Switch on 1500 KHz
Balanced modulator:
Carrier null completely rotates clockwise or counter clockwise so that the modulator is
unbalanced and an AM signal without suppressed carrier is obtained across the output which
amplitude is 200 VP-P.
Local Oscillator:
ACL-AD is 1050 KHz, 2 V
5. Connect load oscillator outpost to LOIN of micro-mixer section.
6. Connect balance modulator-1 OUT to RFIN of micro-section in ACL-AD.
7. Connect the mixer output to IFIN of first IF amplifier in ACL-AD , connect IF OUT of first IFIN1
and IF OUT 2 of first IF to IN2 of second IF amplifier.
8. Observe the modulated signal envelope which corresponds to the waveform of the modulating
signal at output of the balanced modulator of ACC-AM. Connect the oscilloscope to the IN &
OUT POST of envelope detector and detect the AM signal.
9. Check that detected signal follows the behavior of AM signal envelope, vary the amplitude of
the balanced modulator output and check the corresponding variations of demodulated signal.
10. Adjust the input to RFIN POST by varying the output of AM in such a way that you should get
minimum detected output of about 0.3 V at the output of envelope detector.
11. Take the readings as per the table mentioned below for various carrier frequencies&
corresponding local oscillator frequency settings.
7. PROCEDURE:
Selectivity:
1. Refer to the figure and carry out the following connections
2. Connect the output of function generator section (ACL-AM) outpost to the input of balance
modulator (ACL-AM) signal inpost.
3. Connect the output of VCO (ACL-AM) outpost to the input of balance modulator (ACL-AM)
carrier in post.
4. Connect the power supply with proper polarity to the kit ACL-AM & ACC-AW, while
connecting. Ensure that power supply is OFF.
5. Switch on the power supply and carryout the following presetting.
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 34
Function generator:
Sine wave about 0.5 VP-P Frequency about 1KHz
VCO level about 2 VP-P Frequency about 850 KHz
Switch on 1500 KHz
Balanced modulator:
Carrier null completely rotates clockwise or counter clockwise so that the modulator is unbalanced
and an AM signal without suppressed carrier is obtained across the output which amplitude is 50mm
VP-P.
Local Oscillator:
ACL-AD is 1300 KHz, 2 V
1. Connect load oscillator outpost to LOIN of micro-mixer section.
2. Connect balance modulator-1 OUT to RFIN of micro-section in ACL-AD.
3. Connect the mixer output to IFIN of first IF amplifier in ACL-AD , connect IF OUT of first IF
and IF W and IF OUT 2 of first IF to IN2 of second IF amplifier.
4. Connect OUT POST of second IF amplifier to IN POST 2 of second amplifier to IN POST of
envelop detector.
5. Connect the post AGC1 to post AGC2 and jumper position as per diagram.
6. Connect the oscilloscope to the IN and OUT post of envelop detector and detect AM signal.
7. Check the defected signal follows the behavior of the AM signal envelop, measure the detected
signal amplitude.
8. RESULT:
Thus sensitivity & selectivity was obtained successfully .
9. CONCLUSIONS:
Sensitivity mainly depends on the gain of the amplifier present in the receiver.
Selectivity mainly depends on the tuning of the amplifier present in the receiver.
10. VIVA QUESTIONS:
1. Define sensitivity, selectivity and fidelity.
2. Define image frequency.
3. What is the IF frequency of AM-MW &FM Receiver?
4. What are different factors to consider to select IF frequency?
5. Compare Tuned Radio Frequency & Super heterodyne Receivers?
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 35
11. TABULAR COLUMN:
For selectivity:
Carrier
Freq.(KHz)
VCO
860 870 880 890 900 910 920 930 940 950
Output of
Envelope
Detector(mV)
12. MODEL GRAPHS:
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 36
3. BLOCK DIAGRAM:
CPU
Set up arrangement:
RF Signal
Generator
RF Signal
Detector
Display Screen
Buttons
Transmitter Receiver
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 37
8. MEASUREMENT OF HALF POWER BEAM WIDTH (HPBW) AND GAIN OF A HALF
WAVE DIPOLE ANTENNA
1. AIM:
To measure the half power beam width (HPBW) and gain of a half wave dipole antenna.
2. APPARATUS REQUIRED:
1. Transmitter antenna [wired Dipole]-1
2. Receiver antenna [Yagi- Uda antenna]-1
3. Transmitter input Source [RF out]-1
4. Receiver output Detector [RF input]-1
5. SMA to SMN cables-2
6. Personal Computer with AMS software.
4. CIRCUIT OPERATION:
The Half- wave dipole antenna is just a special case of the dipole antenna ,but it is important
to enough that will have its own session .Note that the half wave term means that the length of the
dipole antenna is equal to a half wave length at the frequency of operation.
The small horizontal loop antenna may be rewarded as the magnetic counter part of the short
vertical dipole both loop & dipole have identical fields pattern but with E and H interchanged thus the
horizontal loop is horizontally polarized both small loop and short loop have the same directivity
D=1.5 to quality as a small loop r short loop dipole dimensions should be less.
Let us now proceed to find the fields everywhere around a short dipole. Let the dipole length
‘L’ be placed coincident with the z axis & with its centre at the origin as in fig. The relation of the
electric field components is then as shown it is assumed that the medium surrounding the dipole is air
or vacuum. In delaying with antenna or radiating systems the propagation time is great importance.
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 38
5. CALCULATIONS:
1. Antenna test wave length=
2. Near field boundary=
3. Gain=
4. HPBW=
5. Directivity=
6. FNBW=
7. Antenna Resolution=
8. Antenna Factor=
9. Front to back ratio=
6. TABULAR COLUMN:
S.NO Angle in degrees Power(dB)
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 39
7. PROCEDURE:
1. Set up the experiment as per shown in figure.
2. Set up the distance between antennas to be around 1 meter.
3. Turn ON the module.
4. Open the AMS-B exe-file, select the corresponding comport and click on run. Now the
software will be in running mode.
5. After switch on the AMS module, press menu key and select appropriate experiment shown
in the list [far field pattern].
6. After selecting the far field pattern select appropriate field pattern (Co-Polarization).
7. Use up and down arrows to select type of antenna.
8. Selected the receiver type of antenna.(Yagi-Uda antenna or Loop antenna)
9. Make the dipole length as displayed on the screen.
10. Set the received antenna to zero degrees and press enter key to start the experiment.
11. Then the reading from 00 to 3600 will be plotted in the software and different types of
parameters will be noted from –AMS-B software.
8. RESULT:
1. Gain= _________ dB
2. HPBW=_________
9. CONCLUSION:
1. The operating bandwidth of the antenna depends on the HPBW.
2. Gain of the practical antenna is calculated with the help of reference antenna.
10. VIVA QUESTIONS:
1. How antenna converts electric energy into electromagnetic energy?
2. Define Front to back ratio& Directivity.
3. Define HNBW & FNBW.
3. What is the gain of dipole antenna?
5. Define antenna factor and antenna resolution.
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 40
3. BLOCK DIAGRAM:
CPU
Set up arrangement:
RF Signal
Generator
RF Signal
Detector
Display Screen
Buttons
Transmitter Receiver
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 41
9. MEASUREMENT OF RADIATION PATTERN OF A LOOP ANTENNA IN PRINCIPLE
PLANES
1. AIM:
To measure the radiation pattern of a loop antenna in principle planes.
2. EQUIPMENT REQUIRED:
1. Transmitter antenna [wired Dipole]-1
2. Receiver antenna [Loop antenna]-1
3. Transmitter input Source [RF out]-1
4. Receiver output Detector [RF input]-1
5. SMA to SMN cables-2
6. Personal Computer with AMS software.
4. CIRCUIT OPERATION:
It is shown that the far field pattern of the square and circular loops of the same and are
identical when the loops are small. As a generalized we may say that the properties depend on the
area that the shape of the loop has no effect when the loop is small. However this is not the case when
the loop is large. The pattern of circular loop of any size is dependent of the angle but it is a function
of Ɵ on the other hand, the pattern of a large square loop is a both Ɵ and angle.
Referring to the pattern in a plane normal to the plane of the loop and parallel to the two
sides as indicated by the line AA1, is simply the pattern of two point sources representing sides 2 to 4
of the loop. The pattern in a plane normal to the plane of the loop and passing through diagonal
corners as indicated by the line BB1 is difference. The complete range in the pattern variation as a
function of angle is obtained in this 45ᶱ interval between AA1 & BB1.
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 42
Radiation Pattern:
5. TABULAR COLUMN:
S.No Angle in degrees Power(dB)
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 43
6. PROCEDURE:
1. Set up the experiment as per shown in figure.
2. Set up the distance between antennas to be around 1 meter.
3. Turn ON the module.
4. Open the AMS-B exe-file, select the corresponding comport and click on run. Now the
software will be in running mode.
5. After switch on the AMS module, press menu key and select appropriate experiment shown
in the list [far field pattern].
6. After selecting the far field pattern select appropriate field pattern (Co-Polarization).
7. Use up and down arrows to select type of antenna.
8. Selected the receiver type of antenna.(Yagi-Uda antenna or Loop antenna)
9. Make the dipole length as displayed on the screen.
10. Set the received antenna to zero degrees and press enter key to start the experiment.
11. Then the reading from 00 to 3600 will be plotted in the software and different types of
parameters will be noted from –AMS-B software.
7. RESULT:
Thus the radiation pattern has been obtained successfully.
9. CONCLUSION:
1. The operating bandwidth of the antenna depends on the HPBW.
2. Gain of the practical antenna is calculated with the help of reference antenna.
10. VIVA QUESTIONS:
1. What are the advantages of loop antenna over dipole antenna?
2. Define Front to back ratio& Directivity.
3. Define HNBW & FNBW.
4. What is the gain of dipole antenna?
5. Define antenna factor and antenna resolution
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 44
3. CIRCUIT DIAGRAM:
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 45
1. DIGITAL PHASE DETECTOR
1. AIM: To find the phase difference between two signals.
2. APPARATUS REQUIRED:
a. Aquila Trainer Kit-AET-26B
b. Dual Trace CRO-1
c. Multimeters-2
d.RPS(0-30V)
e. Patch cords
4. CIRCUIT OPERATION:
1. PLL is operated in free running mode at 5KHz by fixing timing resistor Rt=6KΩ & Capacitor
Ct=0.01µf, Two multi meters are connected at Pin no.2&4 to measure the frequencies.
2. The square wave is given to the PLL at pin no.2 and input frequency is varied to operate PLL in
lock range.
3. The phase of input output will differ in the lock range; the input & output of PLL are given to the
XOR Gate to detect the phase difference.
5. PROCEDURE:
1. Switch on the trainer and verify the output of RPS i.e., +5&-5V.
2. Observe the output of square wave generator using CRO &Measure the range with the help of
multimeters, the frequency range should be around 2 KHz to 13 KHz.
3. Calculate the free running frequeny at pin no.4 by varying timing resistor Rt using the formula
fout= 0.3/ Rt Ct, where Ct=0.01µf.
4. Connect two multimeters at pin no.2&pin no.4 of the PLL.
5. The square wave to the input of PLL and short 4&5 pins. Vary the input frequency of the square
wave, If PLL is locked the there exist phase difference between input & output.
6. Connect input &output of PLL to the inputs of XOR gate.
7. Observe the phase difference between input & output.
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 46
6. MODEL WAVEFORMS:
7. RESULT:
Free running frequency_______________ KHz & Rt Value______________ KΩ
8. CONCLUSION:
With the help of PLL &XOR gate phase difference between two square waves can be detected.
9. VIVA QUESTIONS:
1. What are the basic blocks in PLL?
2. Define free running mode of PLL.
3. Define lock range of PLL.
4. Why PLL is operated in lock range to detect the phase?
5. Which logic gate is more suitable for detecting phase difference?
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 47
3. CIRCUIT DIAGRAM:
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 48
2. BALANCED MODULATOR &SYNCHRONOUS DETECTOR
1. AIM: To study the operation of Balanced Modulator &Synchronous Detector
2. APPARATUS REQUIRED:
a. Aquila Trainer Kit-AET-59
b. Dual trace CRO
c. Patch cords
4. CIRCUIT OPERATION:
1. IC-1496 acts as a multiplier & multiplies two input signals ie., RF & AF signals.
2. When the signal is multiplies, sum & difference frequency will be generated.
3. Synchronous detector contains multiplier followed by a LPF.
4. The multiplier multiplies DSB-SC , RF signal & generates Sum & difference frequency.
5. The difference frequency is equal to the AF signal which will appear at the output of the LPF.
4. PROCEDURE:
1. Switch on the trainer and verify the output of RPS i.e., +12V,-12V &-8V.
2. Observe the output of RF generator using CRO, output should be sine wave of frequency 100KHz
& Amplitude should be 300mVp-p
3. Observe the output of AF generator using CRO, output should be sine wave of frequency 5KHz &
Amplitude should be 8Vp-p
4. Connect output of RF, AF Generators to the input of balanced modulator and connect channel1,
channel2 of CRO to the input & output of balanced modulator respectively.
5. Observe the DSB-SC waveform at the output of balanced modulator with respect to input by
varying null adjusts control.
6. Note down peak to peak voltage of DSB-SC.
7. Connect output of RF generator & balanced modulator to the input of synchronous detector.
8. Observe the output of synchronous detector & it should be same as AF signal.
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 49
5. MODEL WAVEFORMS:
ANALOG COMMUNICATION SYSTEMS LAB II B.Tech II SEMESTER
VEMU INSTITUTE OF TECHNOLOGY, DEPARTMENT OF ECE Page 50
6. RESULT:
AF INPUT:
Amplitude____________ VP-P & Frequency _______________KHz.
RF INPUT:
Amplitude____________ VP-P & Frequency _______________KHz.
BALANCED MODULATOR OUTPUT:
Amplitude____________ VP-P & Frequency _______________KHz.
SYNCHRONOUS DETECTOR OUTPUT:
Amplitude____________ VP-P & Frequency _______________KHz.
7. CONCLUSION:
1.180 0 Phase shift occurs in DSB signal when ever AF Signal crosses zero.
8. VIVA QUESTIONS:
1. Write the time expression for DSB-SC signal in the case of single tone, multi tone & band of
frequencies?
2. Draw the frequency spectrum of DSB-SC.
3. Write the power relation in DSB-SC signal.
4. What is power efficiency of DSB-SC signal? What is the percentage of power saving in DSB-SC
with respect to AM?
5. Write the applications of DSB-SC.
Recommended