View
7
Download
0
Category
Preview:
Citation preview
MIDWEST/ MID-AMERICA LANDLORD DESIGN INTENT STARBUCKS COFFEE COMPANY
SITE & BUILDING PLAN CRITERIA
THIS PACKAGE IS CONFIDENTIAL AND SHALL REMAIN THE SOLE PROPERTY OF STARBUCKS CORPORATION. THESE DRAWINGS AND SPECIFICATIONS ARE INTENDED TO EXPRESS DESIGN INTENT FOR A PROTOTYPICAL STARBUCKS STORE (WHICH IS SUBJECT TO CHANGE AT ANYTIME) AND DO NOT REFLECT ACTUAL SITE CONDITIONS. REFERENCE WORK LETTER AND TENANT DRAWINGS FOR PROJECT SPECIFIC INFORMATION.
STARBUCKS TEMPLATE VERSION 2018.07.06
INDEX OF SHEETS:PROTOTYPICAL SINGLE TENANT BUILDING: SITE PLAN REQUIREMENTS _____________________ 2PROTOTYPICAL SINGLE TENANT BUILDING: FLOOR PLAN _________________________________ 3PROTOTYPICAL SINGLE TENANT BUILDING: EXAMPLE UNDERGROUND PENETRATIONS _________ 4PROTOTYPICAL SINGLE TENANT BUILDING: ROOF AND HVAC PLAN _________________________ 5PROTOTYPICAL END CAP / MULTI-TENANT BUILDING: SITE PLAN REQUIREMENTS _____________ 6-7PROTOTYPICAL END CAP / MULTI-TENANT BUILDING: FLOOR PLAN _________________________ 8PROTOTYPICAL END CAP / MULTI-TENANT BUILDING: EXAMPLE UNDERGROUND PENETRATIONS__ 9PROTOTYPICAL END CAP / MULTI-TENANT BUILDING: ROOF AND HVAC PLAN _________________ 10TRASH ENCLOSURE AND SCREEN DETAILS ____________________________________________ 11DRIVE THRU EQUIPMENT DETAILS___________________________________________________ 12-14SITE SIGNAGE AND PAVEMENT GRAPHIC DETAILS ______________________________________ 15DRIVE-THRU CONDUIT SCHEMATIC PLAN______________________________________________ 16SITE SIGNAGE FOOTING DETAILS___________________________________________________ 17ENLARGED PATIO PLAN ___________________________________________________________ 18LANDSCAPE EXAMPLES ___________________________________________________________ 19BUILDING DRIVE-THRU BUMP OUT DETAILS ___________________________________________ 20DRIVE-THRU WINDOW SPECIFICATION _______________________________________________ 21-22 DRIVE-THRU WINDOW SHELF CUT SHEET _____________________________________________ 23EXAMPLE BRAND SIGNAGE ________________________________________________________ 24-26AWNING AND CANOPY DETAILS _____________________________________________________ 27EXAMPLE OF POSSIBLE SIGNAGE LOCATIONS __________________________________________ 28-29BIKE RACK CUT SHEET ____________________________________________________________ 30VEHICLE DETECTOR LOOP CUT SHEET ________________________________________________ 31-32DOOR HARDWARE ________________________________________________________________ 33APPENDIX
2 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
SAMPLE SINGLE TENANT BUILDING: SITE PLAN REQUIREMENTS +/- 2,100 SF
- SEE SPECS AND DETAILS FOR STARBUCKS BRANDED PAVEMENT GRAPHICS.
120’ (7 CAR STACK) MEASURED FROM C.L. OF DT ORDER POINT TO C.L. DT BUMP OUT
A
A
STARBUCKS MINIMUM PARKING RECOMMENDATIONS:- 18 STANDARD- 2 ACCESSIBLE- 20 TOTAL
NOT FO
R CONST
RUCTIO
N
3 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
SAMPLE SINGLE TENANT BUILDING: FLOOR PLAN +/- 2,100 SF
NOT FO
R CONST
RUCTIO
N
4 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
SAMPLE SINGLE TENANT BUILDING: EXAMPLE UNDERGROUND PENETRATIONS +/- 2,100 SF
NOT FO
R CONST
RUCTIO
N
5 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
PREFERRED MANUFACTURERS - CARRIER - TRANE - LENNOX
SAMPLE SINGLE TENANT BUILDING: ROOF AND HVAC PLAN +/- 2,100 SF NOTE: STRUCTURE SHOULD BE ENGINEERED TO SUPPORT (2) 10 TON RTU’S MINIMUM.NOT
FOR C
ONSTRUCT
ION
NT BUILDINT BUILDBE ENGBE EN
6 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
MACRO SITE PLAN EXAMPLESAMPLE END CAP/ MULTI-TENANT BUILDING: SITE PLAN REQUIREMENTS +/- 2,100 SFSEE SPECS AND DETAILS FOR STARBUCKS BRANDED PAVEMENT GRAPHICS.
STARBUCKS MINIMUM PARKING RECOMMENDATIONS:- 18 STANDARD- 2 ACCESSIBLE- 20 TOTALNOT
FOR C
ONSTRUCT
ION
7 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
120’ (7 CAR STACK) MEASURED FROM C.L. OF DT ORDER POINT TO C.L. DT BUMP OUT
A
A
ENLARGED SITE PLAN EXAMPLESAMPLE END CAP/ MULTI-TENANT BUILDING: SITE PLAN REQUIREMENTS +/- 2,100 SFSEE SPECS AND DETAILS FOR STARBUCKS BRANDED PAVEMENT GRAPHICS.
NOT FO
R CONST
RUCTIO
N
8 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
SAMPLE END CAP/ MULTI-TENANT BUILDING: FLOOR PLAN +/- 2,100 SF
NOT FO
R CONST
RUCTIO
N
9 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
SAMPLE END CAP/ MULTI-TENANT BUILDING: EXAMPLE UNDERGROUND PENETRATIONS +/- 2,100 SF
NOT FO
R CONST
RUCTIO
N
10 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
PREFERRED MANUFACTURERS - CARRIER - TRANE - LENNOX
SAMPLE END CAP/ MULTI-TENANT BUILDING: ROOF AND HVAC PLAN +/- 2,100 SF NOTE: STRUCTURE SHOULD BE ENGINEERED TO SUPPORT (2) 10 TON RTU’S MINIMUM.NOT
FOR C
ONSTRUCT
ION
LTI-TENANLTI-TENANBE ENGBE EN
11 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
TRASH/ RECYCLING ENCLOSURE AND REAR SCREEN DETAILSDEDICATED TRASH ENCLOSURE PREFERRED, IF SHARED, SPACE ALLOCATIONS STILL REQUIRED DEDICATED FOR STARBUCKS
12 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
DRIVE-THRU EQUIPMENT DETAILSCOORDINATE SIZE AND LOCATION OF FOOTINGS WITH TENANT DRAWINGS
FINISHGRADE
SIGN WITH BASE ANDPLATE COVER (BYSTARBUCKS)
CONCRETEFOOTING
1 1/
2"
Scale: 1/2" = 1'-0"
DTE - MENU 5 PANEL FREESTANDING
1' -
0"
1' -
11"
2' - 6" 4' - 0" 7' - 3"
2' -
11"
CLR
.12
" M
IN.
20°
(1) CONDUIT, ROUTE TOELECTRICAL PANEL
CONCRETE FOOTING
OUTLINE OF MENU BOARD
CONCRETE FOOTING
OUTLINE OF DIGITAL ORDER SCREEN
EDGE OF CONCRETE CURB
CONDUIT TO CONTROL BOX
DETECTOR LOOP CENTERED ON DIGITAL ORDER SCREEN2" BELOW FINAL GRADE IN CONDUIT OR SAWCUT.
CANOPY ABOVE
MIN. CLR. AREA
16' - 4"
MIN
. CLR
. AR
EA
4' -
3"
NOTES:1. IF UTILIZING EXISTING FOOTING(S) FORSIGNAGE INSTALLATION, FASTEN TOEXISTING THREADED BOLTS AND PROVIDECONDUIT AS NOTED. ENSURE BOLTS ARE INSOUND CONDITION.
2. IF ABANDONING EXISTING FOOTING(S) INPLACE, CUT CONDUIT AND THREADEDBOLTS FLUSH TO TOP OF FOOTING.
3'-0" x 3'-0" MIN. CLEAR AREAFOR CONTROL BOX(2) CONDUIT FROM CONTROL BOX,ROUTE TO DRIVE THRU WINDOW(1) CONDUIT FROM CONTROL BOX,ROUTE TO ELECTRICAL PANEL
OUTLINE OF DIGITAL ORDERSCREEN CONTROL BOX ONCONCRETE FOOTING.
(1) CONDUIT, STUBUP BETWEENCANOPY MESH AND BACKSIDE OF DOS FOR CANOPY UPLIGHT,ROUTE TO SIGNAGE POWER
NON-ILLUMINATED BOLLARD
Scale: 1 DTE - 5 PANEL 20º DT MENU BOARD, DIGITAL ORDER SCREEN WITH CANOPY
FINISHGRADE
SIGN WITH BASE ANDPLATE COVER (BYSTARBUCKS)
CONCRETEFOOTING
Scale:
DTE - PRE-MENU FREESTANDING
MIN
. CLR
. AR
EA
4' -
6"
3' -
0"
30°
OUTLINE OF MENU BOARD
CONCRETE FOOTING SEEADDITIONAL DETAILS FORCONSTRUCTION
(1) CONDUIT ROUTETO SIGNAGE POWER
EDGE OF CONCRETE CURB
20'-0" (6M) TO CENTERLINE OFORDER POINT
CONCRETE CURB
DIGITAL ORDER SCREENWITH CANOPY(BY STARBUCKS)
EXPOSED CONCRETEFOOTING
1 1/
2"
FRONT ELEVATIONLEFT ELEVATIONBACK ELEVATION
CONCRETE CURB
FINISHED DRIVE GRADE
CONCRETE FOOTING
DIGITAL ORDER SCREENWITH CANOPY
(BY STARBUCKS)
FINISH GRADE
EXPOSED CONCRETEFOOTING
DOS CONTROL BOXON UNISTRUT FRAME
Scale:
DTE - DIGITAL ORDER SCREEN AND CONTROL BOX WITH CANOPY
(BY STARBUCKS)
(BY )
(BY )
(BY )
PLAN
13 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
A
BC
DRIVE-THRU EQUIPMENT DETAILS: SINGLE TENANT BUILDING
MIN
.
6"
FLE
X C
ON
DU
IT
1' -
6"
MA
X.
ROUTE DOS POWERWHIP THROUGHMESH OPENING
SECTION
CANOPY BASESHROUD
CANOPY MESH PANEL
CONTROL BOX FASTENEDTO FRAME
1 1/2" SQ. UNISTRUT FRAME;ANCHOR TO FTG.
GRADE
CONDUIT PER ELECTRICAL
CONCRETE FOOTING
CONDUIT WITH WATERTIGHTCOUPLING PER ELECTRICAL
2' -
0"
Scale:
DTE - DOS CONTROL BOX AT CANOPY
FLE
X C
ON
DU
IT
1' -
6"
MA
X.
MIN
.
6"
POST FOOTING BEYOND
GRADE
DOS BASE SHROUD
CONDUIT WITH WATERTIGHTCOUPLING PER ELECTRICAL
DOS POST;CLAMP UNISTRUT TO POSTAND BOLT DCB TO UNISTRUT
DIGITAL ORDER SCREEN BEYOND
2' -
0"
Scale:
DTE - DOS CONTROL BOX
SIDE ELEVATION FRONT ELEVATION
1' -
6"
6"
CONTROL BOX FASTENEDTO FRAME
GRADE
1 1/2" SQ. UNISTRUTFRAME; ANCHOR TO FTG
CONDUIT PERELECTRICAL
CONCRETE FOOTING
2' -
0"
WATERTIGHT COUPLINGPER ELECT.
Scale:
DTE - DOS CONTROL BOX FREESTANDING
14 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
DRIVE-THRU EQUIPMENT DETAILS: END CAP DRIVE-THRU MULTI-TENANT BUILDING
A BCD
MIN
.
6"
FLE
X C
ON
DU
IT
1' -
6"
MA
X.
ROUTE DOS POWERWHIP THROUGHMESH OPENING
SECTION
CANOPY BASESHROUD
CANOPY MESH PANEL
CONTROL BOX FASTENEDTO FRAME
1 1/2" SQ. UNISTRUT FRAME;ANCHOR TO FTG.
GRADE
CONDUIT PER ELECTRICAL
CONCRETE FOOTING
CONDUIT WITH WATERTIGHTCOUPLING PER ELECTRICAL
2' -
0"
Scale:
DTE - DOS CONTROL BOX AT CANOPY
FLE
X C
ON
DU
IT
1' -
6"
MA
X.
MIN
.
6"
POST FOOTING BEYOND
GRADE
DOS BASE SHROUD
CONDUIT WITH WATERTIGHTCOUPLING PER ELECTRICAL
DOS POST;CLAMP UNISTRUT TO POSTAND BOLT DCB TO UNISTRUT
DIGITAL ORDER SCREEN BEYOND
2' -
0"
Scale:
DTE - DOS CONTROL BOX
SIDE ELEVATION FRONT ELEVATION
1' -
6"
6"
CONTROL BOX FASTENEDTO FRAME
GRADE
1 1/2" SQ. UNISTRUTFRAME; ANCHOR TO FTG
CONDUIT PERELECTRICAL
CONCRETE FOOTING
2' -
0"
WATERTIGHT COUPLINGPER ELECT.
Scale:
DTE - DOS CONTROL BOX FREESTANDING
2' -
0"
UNISTRUT FRAME BRACEDTO GRADE PER MFGR.
DCB BOLTED TO FRAME
FINISH GRADE
CONDUIT WITH WATERTIGHTCOUPLING PER ELECTRICAL
1 1/2" SQ. UNISTRUT FRAME;ANCHOR TO WALL
Scale:
DTE - DOS CONTROL BOX WALL MOUNT
15 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
SITE SIGNAGE AND PAVEMENT GRAPHIC DETAILS
5”X5” BLACK STEEL POST2 BANDS OF 1” WHITE REFLECTIVE TAPE.
NOTE: DECOMARK THERMOPLASTIC FOR STAR PATTERN AND WAYFINDING GRAPHIC ARROW IS A LONG LEAD TIME ITEM. THERMOPLASTIC APPLIED GRAPHIC ONLY AVAILABLE THROUGH STARBUCKS SPECIFIED VENDOR.
1a
1b
1c
1d
3
2
2
2
SIGN WITH BASEAND PLATE COVER(BY STARBUCKS)
FINISH GRADE
CONCRETE FOOTING
2' - 1"
6' -
0"
1 1/
2"
2' -
1"
SIGN WITH BASEAND PLATE COVER(BY STARBUCKS)
FINISH GRADE
CONCRETE FOOTING
2' - 1 3/16"
3' -
10"
1 1/
2"
BACKSIDE ELEVATION CUSTOMER ELEVATION
SIGN WITH BASEAND PLATE COVER(BY STARBUCKS)
FINISH GRADE
CONCRETE FOOTING
2' - 2"
3' -
10"
1 1/
2"
SIGN WITH BASEAND PLATE COVER(BY STARBUCKS)
FINISH GRADE
CONCRETE FOOTING
2' - 7"
3' -
10"
1 1/
2"
Scale:
DTE - MONUMENT SIGNScale:
DTE - DIRECTIONAL SIGNScale:
1 DTE - DIRECTIONAL SIGN - ENTRYScale:
DTE - DIRECTIONAL SIGN WITH LOGO - ENTRY
1' - "
SIGN WITH BASE AND PLATECOVER (BY STARBUCKS)
FINISH GRADE
CONCRETE FOOTING
Scale:
DTE - CLEARANCE BAR
8' - 6"
3" 3' - 0" 3" 1' - 6" 3' - 6"
3"3'
- 6
"3"
4' -
0"
Scale:
DTE - WAYFINDING GRAPHICSTAR PATTERN - HORIZONTAL
2' -
10"
5"
FINISH GRADE
CONCRETE FOOTING1 "
Scale:
DTE - NON-ILLUMINATED BOLLARD
2
4
16 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
17 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
SITE SIGNAGE FOOTING DETAILS
18 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
EXAMPLE PATIO RAILING PHOTOGRAPHS
ENLARGED PATIO PLAN
PATIO RAILINGMANUFACTURER: AMERISTAR FENCESTYLE: ECHELON PLUS 3/4 RAIL MAJESTIC PANELHEIGHT: 42” FINISH: BLACK POWDER-COATED ALUMINUM
19 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
INCORRECT CORRECT LANDSCAPE EXAMPLES
• STAKE ALL TREES LESS THAN 1 1/2” CALIPER• TREES ARE NOT TO BLOCK BUILDING OR DIRECTIONAL SIGNAGE• NO BARK MULCH, STRAW OR FLAMMABLE BED FILL• PROVIDE LANDSCAPE PLAN FOR APPROVAL
20 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
DTE - DRIVE THRU WINDOW BUMP-OUT
DRIVE THRU WINDOW
DRIVE THRU SHELF
BUILDING DRIVE-THRU BUMP OUT DETAILS
1
2
3
21 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
DRIVE-THRU WINDOW SPECIFICATION - PREFERRED
1815 Arthur Drive, West Chicago, Illinois 60185 - Direct (630) 876-7766 - Toll Free (800) 621-5045 - Fax (630) 876-7767E-mail: ready@ready-access.com - Web site: www.ready-access.com - Members: CSI, NRA, NAFEM, CFESA
AVAILABLE OPTIONS
The Ready Access AA300 Pass-Thru Air Curtain System is designed to be an integral part of your drive-thru operation by providing comfort for both operator and customer during the coldest of days as well as satisfying health department codes for fly fan application.
Features and BenefitsSatisfies heath department requirements for "Fly Fan" applications while it reduces and deflects the amount of outside wind blowing into the building. This also reduces heating and air-conditioning loss as well as reducing unwanted environment factors such as dust and exhaust fumes from entering the building. Acts as a fly fan to deter insects from entering the building during warm weather conditions.Provides the owner/operator with a stable, comfortable working environment for all crew members. Reduces Drive-Thru operation expenses by diminishing employee turnover.
Modes of OperationThe Ready Access AA300 Pass-thru Air Curtain System is versatile in function and design, offering operators four separate modes of operation. * Outside warm air flow only * Inside warm air flow only * Both outside and inside warm air flow * Outside fly fan operation only
Unique DesignThe AA300 Air Curtain System is the only system on the market today that offers an outside and inside heated air flow. It is designed for use with any flushmount window.
Quality ConstructionThe exterior housing of the AA300 Air Curtain System is manufactured using bronze or clear anodized aluminum.
Fully Assembled, Ready to InstallThe Access Air 300 system is shipped completely pre-assembled and ready for installation, lowering installation costs. Normal installation for new store construction takes less than two hours.
Power coat painting is available upon request for a wide range of custom colors.
Warranty and Service SupportYour Access Air 300 System comes with a one year limited warranty on parts and labor. In addition, each Pass-Thru Air Curtain System is backed by a worldwide service organization.
THE ACCESS AIR 300PASS-THRU AIR CURTAINSYSTEM™For use with the 275 Single Panel Window
1815 Arthur Drive, West Chicago, Illinois 60185 - Direct (630) 876-7766 - Toll Free (800) 621-5045 - Fax (630) 876-7767E-mail: ready@ready-access.com - Web site: www.ready-access.com - Members: CSI, NRA, NAFEM, CFESA
0225
02-A
3002
75
AA300 - 275 PASS-THRU AIR CURTAIN SYSTEM
(406 mm)16"
(187 mm)7-3/8"
(1829 mm)
OF UNIT.
MIN. DISTANCE FROMFLOOR TO BOTTOM
72"
208/240 VOLTS
60 HZ600 FPM AIR VELOCITY
7100 HEATER WATTS32 ACTUAL UNIT AMPS1 (SINGLE) PHASE
(251 mm)
(114 mm)
(413 mm)ROUGH OPENING
16-1/4"
(1213 mm)47-3/4"
ROUGH OPENING
(254 mm)
(152 mm)
(553 mm)21-3/4"
13-7/8"(352 mm)
6"
10"(1207 mm)47-1/2"
UNIT SPECIFICATIONS:
4-1/2" REF.
9-7/8"
FINISH TO MATCH STOREFRONT GLAZING SYSTEM
22 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
1815 Arthur Drive, West Chicago, Illinois 60185 - Direct (630) 876-7766 - Toll Free (800) 621-5045 - Fax (630) 876-7767E-mail: ready@ready-access.com - Web site: www.ready-access.com - Members: CSI, NRA, FEDA, NAFEM, CRA
STANDARD OPTIONS
PRODUCT DESCRIPTIONS
For retail operators who want to get an edge on their competition by offering customers convenient, face-to-face service, the 275 Single Panel Slider is perfect. Ideal for fast food, walk-up service, and many other applications.
4 Standard Sizes Available- 47 1/2"W x 43 1/2"H with a 19" wide x 36" high service opening- 47 1/2"W x 35 3/4"H with a 19" wide x 28" high service opening- 47 1/2"W x 35 3/4"H with a 15" wide x 28" high service opening- 35 3/4"W x 35 3/4"H with a 14" wide x 28" high service opening (SC / MOER)- Passes California restricted opening requirements of 432 square inches.
3 Modes of Operation- 275 Manual Open/Self ClosingSo simple to operate, the service door opens effortlessly and automatically slides shut when operator releases the handle.
- 275 M.O.E.R. (Manual Open/Electronic Release)The 275 Manual Open/Electronic Release Window has a manual open, self closing operation which electro-magnetically holds the window open until the operator finishes their transaction and steps out of the presence sensor. This unit is field adjustable to the length of time the window will stay open.
- 275 ElectricWith a hands-free operation the 275 Electric Window is ideal for heavy traffic situations. It provides easier operation and speedier service than the manual operating windows. This unit is field adjustable to the length of time the window will stay open.
Quality ConstructionAnodized aluminum extrusions, stainless steel and 1/4" tempered glass combine to give you an attractive window that not only enhances building exteriors, it will not rust, pit or weather. Track free bottom sill provides for a contaminant free surface.
Triple Security LocksThe 275 automaticaly locks each time the window closes, providing security when the window is left unattended. When the drive-thru is closed, thumbturn & night security bar helps prevent outside entry. In high risk locations, an optional security bar set is available.
The 275 series window is available in statuary bronze, or clear anodized aluminum.
A retrofit kit is available for the 275 Self Closer that easily upgrades the window from a manual operation to a MOER or fully automatic electric operation.
Right to left or left to right opening available (as seen from outside view).For non food service applications window can be made manual open / manual close.
Fully Assembled, Ready to InstallReady Access windows are shipped completely preassembled, and fully glazed for lower installation costs. Normal installation takes less than two hours.
Warranty and Service SupportYour Ready Access window comes with a one year limited warranty on parts and labor. Each window is backed by a worldwide service organization.
CUSTOM OPTIONSCustom sizes are available to satisfy any unusual operations requirement or health department code.Tinted glass is available upon request.Powder coat painting is available in a wide range of custom colors.
275 SINGLE PANEL SLIDER SERIES
Unique DesignBottom sill is angled downward to provide protection against the elements such as rain, sleet, and snow.
1815 Arthur Drive, West Chicago, Illinois 60185 - Direct (630) 876-7766 - Toll Free (800) 621-5045 - Fax (630) 876-7767E-mail: ready@ready-access.com - Web site: www.ready-access.com - Members: CSI, NRA, NAFEM, CFESA
0225
02-275
275 SERIES
275 - 47-1/2"W x 43-1/2"HGlazing Rough Opening = 47-3/4"W (1213 mm) x 43-3/4"H (1111 mm)Masonry Rough Opening =48"W (1219 mm) x 44"H (1118 mm)
275 - 47-1/2"W x 35-3/4"HGlazing Rough Opening = 47-3/4"W (1213 mm) x 36"H (914 mm)Masonry Rough Opening =48"W (1219 mm) x 36-1/4"H (921 mm)
275 - 35-3/4"W x 35-3/4"HGlazing Rough Opening = 36"W (914 mm) x 36"H (914 mm)Masonry Rough Opening =36-1/4"W (921 mm) x 36-1/4"W (921 mm)
TWO STANDARD WINDOW HEIGHTS43-1/2" H WITH 19"W x 36"H SERVICE 35-3/4" H WITH 19"W x 28"H + 15"W x 28"H SERVICE
36"
"H" ROUGH OPENING
"W" ROUGH OPENING
(102 mm)4"
(1207 mm)
(1105 mm)
SERVICE OPENING19" X 36"
43-1/2"
47-1/2"
MIN. DISTANCEFROM TOP OFSILL TO FLOOR(914 mm) PRESENCE
SENSOR
BOTH SIDE FRAMES ARE HOLLOWFOR ELECTRICAL ACCESS FROM EACHCORNER LEADING TO THE HEADER.
INTERNATIONAL : 220/240 vac - 50/60 Htz WITH A MAX. 8 amp BRANCH CIRCUIT
ELECTRICAL REQUIREMENTSUSA (DOMESTIC) : 115 vac - 60 Htz WITH A 15 amp BRANCH CIRCUIT
POWER HOOK-UPINSIDE OF HEADER
FOR FULLY AUTOMATIC ELECTRIC UNIT
DRIVE-THRU WINDOW SPECIFICATION - TRADE DOWN
FINISH TO MATCH STOREFRONT GLAZING SYSTEM
23 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
DRIVE-THRU WINDOW SHELF CUT SHEET
302 STAINLESS STEEL
24 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
PYLON SIGN A
DRIVE THRU DIRECTIONAL SIGNAGE
B
DRIVE THRU DIRECTIONAL WAYFINDING SIGNAGE
C
CLEARANCE BAR: NON-ILLUMINATEDD
DRIVE THRU MONUMENT SIGNAGE (CAN BE MODIFIED)
E
EXAMPLE ILLUMINATED BRAND SIGNAGE
25 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
NOTE: LAYOUTS AND PROPORTIONS ARE FOR DESIGN INTENT ONLY.EXAMPLE BRAND SIGNAGE - MONUMENT SIGN PANEL
1' -
4"
6 3/
4"
6' -
0"
3' -
1"1'
- 0"
1"1
1/2"
1' -
8 1/
2"
4 1/
2"3
1/4"
4 1/
2"
ISOMETRIC VIEW PLAN
ELEVATIO
6' - 0"
1' -
4"
6 3/
4"
EQ3' - 1"EQALUMINUM COVERPAINTED BLACK
MASONRY BASE BELOWTO MATCH BUILDING
ANCHOR BOLTS ANDBASE PLATE
6' -
0"
3' -
1"1'
- 0"
1"1
1/2"
1' -
8 1/
2"
4 1/
2"3
1/4"
4 1/
2"
ALUMINUM RETAINERWITH 1" RETURNPAINTED BLACK
WHITE POLY-CARBONATE WITHFIRST SURFACE VINYLFILM
ALUMINUM FILLERPAINTED BLACK
COPY AND CHEVRONSBACKED UP WITH WHITEPOLYCARBONATE
MASONRY BASE TOMATCH BUILDING
ALUMINUM COVERPAINTED BLACK
FINISH GRADE
PLAN
ELEVATION
26 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
EVOLVE LOGO DISK FLUSH MOUNTED A
DRIVE THRU CABINET FLUSH MOUNTED. B
INLINE WORDMARK FLUSH MOUNTED (COLOR SELECTION DEPENDS ON BUILDING MATERIALITY)
C
STACKED WORDMARK FLUSH MOUNTED (COLOR SELECTION DEPENDS ON BUILDING MATERIALITY)
D
EXAMPLE ILLUMINATED BRAND SIGNAGE - BUILDING SIGNAGE
27 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
FABRIC AWNING SPECIFICATION:BLACK - SUNBRELLA BLACK #4608
AWNING AND CANOPY DETAILS: DESIGN INTENT ONLY
1
'L' ANGLE
TUBE STEEL
'C' CHANNEL; FINISHTO BE DETERMINED
ROOF SOFFIT
WOOD BLOCKING
1" GAGE ROOF DECKING
PL STEEL; FINISH TO BEDETERMINED
1" DIA. TIE ROD W/ CLEVIS.FINISH TO BE DETERMINED
WOOD BLOCKING
ROOF INSULATIONROOF MEMBRANE LAYER
MTL FLASHING; FINISH TO BEDETERMINED
WELD PLATE TO TUBESTEEL
1' -
0"
4" CHANNEL STEELl
SUPPORT STRUT
STEEL SLATS
32°
3' -
0"
2' -
0"
5' - 0"
1' -
0"
ATTACH TO WALL PERSTRUCTURAL DRAWINGS.PROVIDE FLASHING AND SEALANTAT STRUCTURAL CONNECTIONS
FABRIC AWNING DETAIL:1
ARCHITECTURAL METAL CANOPY DETAILS:3
3/8" PLATE
PLATE
1" DIA. TIE-ROD W/ CLEVIS
5X5X3/8" PLATE EA. SIDE OFWALL W/ (4) - 1/2" DIA. THRU
BOLTS AT 3" SPACING & GAGE
5X5X3/8" PLATE
METAL FLASHING
WHITE THERMOPLASTICROOFING SYSTEM
4" ROOF INSULATIONMINIMUM 1:12 SLOPETOWARD DRAIN
ERIOR FINISH
METAL FLASHING
1" GAGE ROOFDECKING
BLACK COMPOSITE
RECESSED LED CANCENTERED IN CANOPY
SOLAR SCREEN DETAIL:2
SUNBRELLA " " #ABRIC AT SLOPED AND
VERTICAL FRONT END
4' - 0"
1' -
10"
6"
NOTE: AWNING VENDOR TO FIELD VERIFY AWINING DIMENSIONS AND CONFIRM DESIGN WITHSTARBUCKS DM PRIOR TO CONSTRUCTION
FABRIC PANEL
1" (25MM) SQUAREEXTRUDED ALUMINUMTUBE FRAME
TEK SCREW
USE 2 ANCHORBOLTS PERFRAMEMOUNTINGBRACKET.
TEK SCREW
FRAME MOUNTING BRACKETSPACED EVERY 2'-0" TOP.
USE 2 ANCHORBOLTS PERFRAMEMOUNTINGBRACKET.
FRAME MOUNTINGBRACKET SPACED EVERY2'-0" TOP.
28 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
EXAMPLE OF POSSIBLE SIGNAGE LOCATIONS
1. WEST ELEVATION (VIEW FROM ENTRY TO SHOPPING COMPLEX)
3. EAST ELEVATION (FACING ADJACENT STRIP MALL) 4. SOUTH ELEVATION (FACING STREET)
2. NORTH ELEVATION (FACING COMPLEX)
BLACK METAL CANOPY
BLACK METAL CANOPYOR FABRIC AWNING
TOWER ELEMENT TOBE SIZED TO ACCEPTSTARBUCKS SIGNAGE
BLACK METAL CANOPY
DOWNSPOUTS NOT TOCONFLICT WITH SIGNAGE
BLACK METAL CANOPYOR FABRIC AWNING
BLACK METAL CANOPY
PAINT REARDOOR TO MATCHSURROUNDINGMATERIAL
29 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
EXAMPLE STORES
30 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
BIKE RACK CUT SHEETEQUIVALENT SUBSTITUTIONS PERMITTED. PROVIDE SUBSTITUTED SPEC. TO STARBUCKS FOR REVIEW AND APPROVAL.
����
������� ���������
� ����� �������������������
���
������������ ��
��� !"#$ !"#$
������� ���������
��% �&!
��� �������
Black
31 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
VVDL100 Vehicle Detector Loop
INSTALLATION INSTRUCTIONS The following instructions are for installation of the HME VDL100 Vehicle Detector Loop in a single drive-thru traffic lane, for vehicle detector use with any HME drive-thru communication system. The loop should be installed prior to pouring concrete for paving the lane, and therefore requires coordination with the paving contractor. Pay careful attention to the illustrations on the back of this page, especially regarding loop dimensions and the depth and position of its installation. A loop must always be installed at the speaker post or menu board. If you received two loops, the second loop should typically be installed at the service window. If you received three loops, the third loop should typically be installed at the cashier window. Locations of the second and third loops may vary depending on specific requirements.
NOTE: In some cases the distance from the loop to where the conduit exits the ground into the speaker post cabinet may exceed three feet. In such cases, an additional ½ inch (12.7 mm) PVC pipe will be required (not provided).
LOOP AREA PREPARATION (Refer to Figure 1) The loop should begin 12 to 18 inches (305 – 457 mm) out from the curb. The forward edge of the loop should be lined up with the midpoint of the menu board, speaker post or drive-thru window. A 3 foot (914 mm) perimeter, free from rebar, wire screen, reinforcing bars, electrical cable or metal objects should be provided. Any metal nearby disturbs the loop’s magnetic field, thus reducing the field in which detection takes place. Electrical cables near the loop can possibly cause false impulses to the magnetic field generated by the loop, causing erratic operation of the detector.
TOOLS/MATERIALS REQUIRED Shovel; hacksaw; tape measure; wood supports; securing wire; PVC adhesive & brush
PARTS LIST Prefab (folded) loop, 1.5 feet (.46 meter) x 5 feet (1.52 meter) 1 ea Coupling for ½ inch (12.7 mm) PVC tubing 1 ea 90 degree elbow for ½ inch (12.7 mm) PVC tubing 1 ea ½ inch (12.7 mm) PVC tubing, 2 feet (.61 meter) long 1 ea ½ inch (12.7 mm) PVC tubing, 3 feet (.91 meter) long 1 ea
PROCEDURE Check the contents of this package against the parts list. If any item is missing, contact your HME sales representative. Remove the elbow coupling, Figure 2 (6), from the cable. The cable was threaded through the coupling for shipping only. Assemble the loop as instructed on the back of this page. Measure the distance from the curb to the outlet of the conduit that comes from the building into the speaker post or menu board to determine if the enclosed 3 foot (.91 meter) PVC loop extension reaches from the loop to the conduit as shown in Figure 2 (4). If it does, proceed to the next paragraph. If not, substitute a longer piece of ½ inch (12.7 mm) PVC pipe (not provided). Measure and cut the pipe to reach from the loop to the point where it must exit the ground into the speaker post.
Figure 2. Loop layout and connections Figure 1. Loop area preparation
NOTE: PVC adhesive (not provided) must be applied wherever PVC couplings and pipe are fitted together. Flatten the loop (folded for shipping) as shown in Figure 2 (1). Fit the pipe securely into the couplings (2).
Lay the loop flat in the drive-thru lane and position it as shown in Figure 2. Elevate the loop on supports that are anchored to the ground, as shown in Figure 3. Level the loop so it will be 2 inches (51 mm) or less from the paved surface when the concrete is poured. Fasten the loop to the supports with wire, so it will not float when the concrete is poured.
Pull the loop wires through the sleeve coupling (3) and the PVC loop extension (4). Slide one end of the sleeve coupling (3) over the nipple on the corner fitting of the loop (5), and slide the end of the loop extension (4) into the other end of the sleeve coupling (3).
Pull the loop wires through the elbow coupling (6) and the remaining 2 foot (.61 meter) piece of PVC (7). Slide the two ends (of 4 & 7) into the coupling (6), positioning the piece of PVC (7) so it points upward, out of the ground. Be certain it is next to and parallel to the outlets of the conduit coming into the speaker post or menu board from the building.
Waste Electrical and Electronic Equipment (WEEE)
Figure 3. Side view of loop in asphalt or concrete
The European Union (EU) WEEE Directive (2002/96/EC) places an obligation on producers (manufacturers, distributors and/or retailers) to take-back electronic products at the end of their useful life. The WEEE Directive covers most HME products being sold into the EU as of August 13, 2005. Manufacturers, distributors and retailers are obliged to finance the costs of recovery from municipal collection points, reuse, and recycling of specified percentages per the WEEE requirements.
Instructions for Disposal of WEEE by Users in the European Union The symbol shown below is on the product or on its packaging which indicates that this product was put on the market after August 13, 2005 and must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of the user’s waste equipment by handing it over to a designated collection point for the recycling of WEEE. The separate collection and recycling of waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local authority, your household waste disposal service or the seller from whom you purchased the product.
VEHICLE DETECTOR LOOP CUT SHEET - OPTION 1 (POUR IN PLACE)
32 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
Saw-Cut Vehicle Detector Loop INSTALLATION INSTRUCTIONS
These instructions are for saw-cut loop installation in an existing concrete or asphalt drive-thru traffic lane, for use with HME’s Drive-Thru Audio or Timer Systems. Refer to the illustrations on the back of this page. Note the differences in loop location for audio systems and timer systems. Failure to follow these instructions in saw-cut vehicle detector loop installation may cause your HME Drive-Thru Audio System or Timer System warranty to be voided.
TOOLS/MATERIALS REQUIRED Drill with ¾ inch (19 mm) drill bit (optional) Type #20 AWG XLPE cable, 100 feet (30.5 meters) Concrete and mortar-repair sealant (Quikrete Hydraulic Water-Stop Cement or equivalent) CAUTION: Hard setting epoxies should never be used.
S/G foam tubing, 3 feet (.91 meter) Concrete-cutting saw Marking chalk
PROCEDURE Carefully examine the illustrations on the back of this page before proceeding.
Lay out and mark with chalk, the exact size and location of the slot before cutting it. The rectangular slot should begin 12 – 18 inches (305 – 457 mm) out from the curb, with its forward edge even with the midpoint of the menu board, speaker post (Location 1) or drive-thru window (Location 2). Its dimensions should be 5 feet (1.52 meters) across the drive-thru lane, and 18 inches (457 mm) wide. CAUTION: If the loop is being installed in an existing cut, or over an existing loop that is being deactivated, cut through the old loop in 5 or 6 places so it will not interfere with the new loop. Also, if there is a control joint in the concrete, the loop should not span it. BE AWARE: A 3 foot (.91 meter) perimeter, free from rebar, wire screen, reinforcing bars, electrical cables or other metal objects should be provided around and under the loop area. Any metal within this perimeter disturbs the loop’s magnetic field, thus reducing the field in which detection takes place. Cut the slot ¼ inch (6.25 mm) wide, and 1½ – 2¼ inches (38 – 52 mm) deep, along the chalk lines to form a basic rectangular loop. Make an additional 45º angle cut at each of the four corners of the rectangle, to prevent sharp, 90º angles of the concrete from damaging the loop-wire insulation. (If 45º angles are not cut, a ¾ inch [19 mm] hole must be drilled at each corner.) Also cut a lead-wire slot, ¼ inch (6.25 mm) wide and 1 inch (25 mm) deep, from one corner of the rectangular loop cut to a point nearest the conduit through which the cable is routed into the store. Clean the slot thoroughly with compressed air, and allow the slot and the area around it to dry completely. Be sure no moisture or sand gets back into the slot while the loop is being installed. Allowing sufficient lead wire to be routed from the speaker post or menu board into the store, to the audio system base station or timer control unit, lay the first turn of wire in the slot in a clockwise direction, routing it through the 45º angle cuts at each corner. CAUTION: A continuous piece of unspliced wire must be used. Avoid damaging the insulation on the wire. Nicks or abrasions can permit moisture to enter the loop, making it inoperable. Gently press the wire down to the bottom of the slot, all the way around the loop, with a blunt wooden stick. Do not use a metal instrument or tool. Lay six turns of wire in the slot. After the last turn, lay 3 inch (76 mm) lengths of foam tubing, evenly spaced, on top of the wire to hold it in place in the slot. Fill the slot completely with sealant, covering the wire completely so it is not visible. Cut the remaining wire to equal the length of the lead wire, twist the two wire ends together to form a twisted pair, with five turns per foot. This twisted pair should go into the lead-wire cut. Before applying the sealant, test the loop for insulation resistance and DC continuity resistance. If the DC resistance is greater than 3 ohms, or the insulation resistance to ground is less than 100 megohms, the wire is damaged and the entire loop must be replaced. Apply the sealant. Solder and insulate all connections to lead wires.
Figure 1. Saw-cut loop locations
Figure 2. Saw-cut loop parameters
Figure 3. Saw-cut loop side view
Waste Electrical and Electronic Equipment (WEEE) The European Union (EU) WEEE Directive (2002/96/EC) places an obligation on producers (manufacturers, distributors and/or retailers) to take-back electronic products at the end of their useful life. The WEEE Directive covers most HME products being sold into the EU as of August 13, 2005. Manufacturers, distributors and retailers are obliged to finance the costs of recovery frommunicipal collection points, reuse, and recycling of specified percentages per the WEEE requirements.
Instructions for Disposal of WEEE by Users in the European Union The symbol shown below is on the product or on its packaging which indicates that this product was put on the market after August13, 2005 and must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of the user’s waste equipment by handing it over to a designated collection point for the recycling of WEEE. The separate collection and recycling of waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contactyour local authority, your household waste disposal service or the seller from whom you purchased the product.
VEHICLE DETECTOR LOOP CUT SHEET - OPTION 2 (SAW-CUT)
33 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
DOOR HARDWARE
34 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
APPENDIX:
SITE PLAN AND FLOOR PLAN EXAMPLES
35 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
STARBUCKS COFFEE 2148 SF
A-1001.11
EQ7'
- 0"
EQ
PARKING
PA
RK
ING
PA
RK
ING
Y 14323
Y 14324
2
3
EQ7' - 0"
EQ
EQ7'
- 0"
EQ
Y 14324
Y 143232
3
EQ 7' - 0" EQ
2Y 14323
Y 14324 3
4
4
4
4
4
4
55
5
6
7
7
9
10
10 10
10
11
9
9
9
S 141041
S 141041
EQ 7' - 0" EQ
Y 143243
Y 14323
A-10047
A-1002.11
A-10024
A-10023
8S X2002
A-1002.12
ADJACENT TENANTS
10
8S X2002
1' -
0"
80' - 5"
12
2
36 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
37 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
30'R
/WEA
SEME
NT
T
DESI
GNAT
EDFL
OODW
AY(75
'FRO
MPR
OPER
TYLIN
E)
DO NOT ENTER
DO N
OT E
NTER
A-2001 1
A-20021
A-2002
2
A-2001
2
A-10026
A-10022
S 14104
S 14104
Y 14103
S X2001
EQ.
7' -
0"EQ
.
Y 14324
Y 14323
EQ 7' - 0" EQ
Y 14324 Y 14323
A-10047
7' - 6"
1' - 6"
Y 14101
S 14106
EQEQ Y 14323
EQEQ
Y 14323
EQEQY 14323
3' -
9"
3
5
6
1
56
5
5
11
10
12
5
1
77
7
7
7 7
48
7
7
9
2
A-10025
STARBUCKS COFFEE 2232 SF
A-1001.11
PARKING
PARKING
6'- 0
"
131 2 3 4 5 6 7 81 2 3 4 5 6 7 8
1' - 8" 3' - 10 1/4"
33°
13
CAUDILLDRIVE
A-10054
A-1005
4B
4A
ARCHITECTURAL SITE PLAN
38 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
STARBUCKS COFFEE2,450 SF
Y 14323
Y 14324
Y 14323
Y 14324
Y 14324
Y 14324Y 14324
Y 14324
Y 14101
Y 14095
Y 14093
Y X0001
Y X0001
S 14091
S 14327
S 14327
S 14327
Y X0002
1 2 3
4
5
6
7
Y 14119
Y 14163 Y 15700Y 14116Y X0002
Y 14120
Y X0005 (2)
Y X0003
S 14106
Y X0002
S X0004 (2)
12' - 0"
12' - 0"
12' -
0"
Y 10020
Y 16628Y 12147 (3)
(3)
EASTGATE
N. R
D.
4
4
5
5
5
6
7
8
9
10
11
11
18
13
13
13
1313
13
13
1314
14
14
15
16
17
18
12
19
20
20
21
22
23
23
23
23
24
24
18' - 0"
12' - 0"
A-40012
A-40011
A-40022
A-40021
A-40015
A-40013
A-40014
19' -
6"
EQEQ
EQ11
' -0"
EQ
EQ11
' -6"
EQ
Y X000214
S X0004 (2) ADDITIONAL PANELSAT OFFSITE MONUMENT SIGN
X0003 1 PATIO RAILING LL-LL MANUFACTURER: AMERISTAR FENCESTYLE: ECHELON PLUS 3/4 RAILMAJESTIC PANEL FINISH: BLACKPOWDER-COATED ALUMINUM
X0005 2 DERO HOOP RACK SB-GC MODEL : HR-FT-EPX-BLACK.
39 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
.
AD
A
AD
A
ADA
G 12688 G 14298 DA
G 12680C
G 12689
EG 14403
B
G 12689
G 14403 E
B
WORKROOM
UNISEXRESTROOM
UNISEXRESTROOM
RESTROOMVESTIBULE
CAFE/SEATING
BEVERAGE PREP.
RETAIL
ENTRYVESTIBULE
40 | STARBUCKS COFFEE COMPANY | MIDWEST/MID-AMERICA LANDLORD DESIGN INTENT | CHICAGO DESIGN STUDIO | 06 JULY 2018
RETAIL
BEVERAGEPREP.
CAFE/SEATING
WORKROOM
UNISEXRESTROOM
RESTROOM VESTIBULE
UNISEXRESTROOM
VESTIBULE ENTRY VESTIBULE
G 12688
G 14298D
AG 12680
C
E
B G 14403
G 12689
E
B
3"
3"
3"
3"
6"1' - 0"
ADA
ADA
G 14403
G 12689
Recommended