View
6
Download
0
Category
Preview:
Citation preview
PERFORMANCE SPECIFICATIONSFlow Rate Adjustable to 0-43 gpm (162.8 LPM)Port Size Suction 1” 150# ANSI/DIN 325 Flange Discharge 1” 150# ANSI/DIN 325 FlangeAir Inlet . . . . . . . . . . . . . . . . 3/8” NPTAir Exhaust . . . . . . . . . . . . . 1/2” NPTSuction Lift Dry . . . . . . . . . . . . . . . . . 11’ (3.4 m) Wet . . . . . . . . . . . . . . . . . 31’ (9.4 m)Max Solid Size (Diameter) . . . . . . . . . . . . . . . . . .1/8” (3.1 mm)Max Noise Level . . . . . . . . . 94 dB(A)Shipping Weights Polypropylene . . . . . . 17 lbs (7.7 kg) PVDF . . . . . . . . . . . . 22 lbs (10 kg)
E1 DATA SHEETSPECIFICATIONS & PERFORMANCE
1” Bolted Plasticwith Plastic Center Section
©Copyright 2019 Warren Rupp, Inc. All Rights Reserved.
e1nmdlCds-rev0519
Warren Rupp, Inc. | A Unit of IDEX Corporation800 North Main Street | Mansfield, OH 44902 USAPhone: 419.526.7296 | Fax: 419.526.7289
VERSAMATIC.COM
0 20 40 60 80 100 120 140
Disc
harg
e Hea
d in
PSI
Meters Feet
240
220
200
180
160
140
120
100
80
60
40
20
0
75 70 65 60 55 50 45 40 35 30 25 20 15 10 5 0 0
1
3
2
4
5
6
7
BAR
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Capacity Per Stroke: 0.047 Gal (0.18 L)
0
20
40
60
80
100
0 5 10 15 20 25 30 35 40
5 10
20
30
AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI
SCFM M3/HR 5 8.5 10 17 20 34 30 51
NOTE: Performance based on the following: elastomeric fitted pump, flooded suction, water at ambient conditions. The use of other materials and varying hydraulic conditions may result in deviations in excess of 5%.
E1 DATA SHEETSPECIFICATIONS & PERFORMANCE
1” Bolted Plasticwith Plastic Center Section
©Copyright 2019 Warren Rupp, Inc. All Rights Reserved.
e1nmdlCds-rev0519
Warren Rupp, Inc. | A Unit of IDEX Corporation800 North Main Street | Mansfield, OH 44902 USAPhone: 419.526.7296 | Fax: 419.526.7289
VERSAMATIC.COM
DIMENSIONS
E1 Bolted Plastic Dimensions in inches (mm dimensions in brackets) The dimensions on this drawing are for reference only. A certified drawing can be requested if physical dimensions are needed.
E1 Bolted Plastic (Center Ported Manifold Option) Dimensions in inches (mm dimensions in brackets) The dimensions on this drawing are for reference only. A certified drawing can be requested if physical dimensions are needed.
2.23
11.75
10.83
[56.64]
[298.45]
[275.01]
1" ANSI 150# / DIN 325SUCTION FLANGE
3/8" NPTAIR INLET
3.64
16.49
.49
9.13
8.13
10.09
[92.46]
[418.85]
[12.45]
[231.9]
[206.5]
[271.53]
1/2" NPTAIR EXHAUST
5.13
6.20
4.10
7.85
1.66
[130.3]
[157.48]
[104.14]
[199.39]
[42.16]
BOTTOM VIEW
1" ANSI 150# / DIN 325DISCHARGE FLANGE
2.23
11.75
10.83
[56.64]
[298.45]
[275.01]
1" ANSI 150# / DIN 325SUCTION FLANGE
3/8" NPTAIR INLET
3.64
16.49
.49
9.13
8.13
10.09
[92.46]
[418.85]
[12.45]
[231.9]
[206.5]
[271.53]
1/2" NPTAIR EXHAUST
5.13
6.20
4.10
7.85
1.66
[130.3]
[157.48]
[104.14]
[199.39]
[42.16]
BOTTOM VIEW
1" ANSI 150# / DIN 325DISCHARGE FLANGE
2.23
11.75
10.83
[56.64]
[298.45]
[275.01]
1" ANSI 150# / DIN 325SUCTION FLANGE
3/8" NPTAIR INLET
3.64
16.49
.49
9.13
8.13
10.09
[92.46]
[418.85]
[12.45]
[231.9]
[206.5]
[271.53]
1/2" NPTAIR EXHAUST
5.13
6.20
4.10
7.85
1.66
[130.3]
[157.48]
[104.14]
[199.39]
[42.16]
BOTTOM VIEW
1" ANSI 150# / DIN 325DISCHARGE FLANGE
13.52343.41
11.48291.47
16.94430.15
3/8" NPTAIR INLET
2.5063.50
14.75374.65
.4912.45
9.81249.22
8.13206.38 1" ANSI 150# / DIN 325
DISCHARGE FLANGE
1" ANSI 150# / DIN 325SUCTION FLANGE
1/2" NPTAIR EXHAUST
4.12104.65 5.13
130.30
5.50139.70
7.16181.86
1.6642.16
R.256.35
BOTTOM VIEW
13.52343.41
11.48291.47
16.94430.15
3/8" NPTAIR INLET
2.5063.50
14.75374.65
.4912.45
9.81249.22
8.13206.38 1" ANSI 150# / DIN 325
DISCHARGE FLANGE
1" ANSI 150# / DIN 325SUCTION FLANGE
1/2" NPTAIR EXHAUST
4.12104.65 5.13
130.30
5.50139.70
7.16181.86
1.6642.16
R.256.35
BOTTOM VIEW
13.52343.41
11.48291.47
16.94430.15
3/8" NPTAIR INLET
2.5063.50
14.75374.65
.4912.45
9.81249.22
8.13206.38 1" ANSI 150# / DIN 325
DISCHARGE FLANGE
1" ANSI 150# / DIN 325SUCTION FLANGE
1/2" NPTAIR EXHAUST
4.12104.65 5.13
130.30
5.50139.70
7.16181.86
1.6642.16
R.256.35
BOTTOM VIEW
Recommended