View
1
Download
0
Category
Preview:
Citation preview
www.shinelight.cc Tel: 86-573-87967809 Fax: 86-573-87967851 sales@shinelight.cc
SHINELIGHT TECHNOLOGY CO., LTD
120W Constant Current Output LED Driver
FEATURES
High Efficiency
Build-in Active PFC
Constant Output Current
Waterproof (IP67)
All-Round Protection: OVP, SCP, OTP
Dimming Function Optional (0-10V、PWM、Timer)
SHC120/SHD120/SHP120/ SHT120 SERIES SPECIFICATIONS
Model
Output
Current
(±5%) (mA)
Output
Voltage
(V)
Efficiency PF No Load
Output
Voltage
(±5%) (V)
Ripple &
Noise (V) 110V
Input
220V
Input
110V
Input
220V
Input
SH*120-0350SW 350 206 ~ 343 91.0% 93.0% 0.99 0.96 360 10.7
SH*120-0450SW 450 160 ~ 267 91.0% 93.0% 0.99 0.96 280 8.3
SH*120-0700SW 700 103 ~ 172 90.0% 92.0% 0.99 0.96 180 5.4
SH*120-1050SW 1050 69 ~ 114 89.0% 91.0% 0.99 0.96 120 3.6
SH*120-1400SW 1400 52 ~ 86 89.0% 91.0% 0.99 0.96 91 2.7
SH*120-1750SW 1750 42 ~ 69 88.0% 90.0% 0.99 0.96 72 2.1
SH*120-2100SW 2100 35 ~ 58 88.0% 90.0% 0.99 0.96 61 1.8
SH*120-2800SW 2800 26 ~ 43 88.0% 90.0% 0.99 0.96 45 1.4
SH*120-3150SW 3150 23 ~ 38 87.5% 89.5% 0.99 0.97 40 1.2
SH*120-4200SW 4200 18 ~ 29 87.5% 89.5% 0.99 0.97 31 0.9
NOTE: 1. All specifications are typical at 25°C unless otherwise stated.
2. The “Efficiency” & “PF” values are measured at full load, after the unit is thermally stabilized,
otherwise they will be lower about 1%.
3. The “Ripple & Noise” values are measured by 20MHz bandwidth oscilloscope and the output
paralleled a 0.1uF ceramic capacitor and a 10uF electrolytic capacitor.
www.shinelight.cc Tel: 86-573-87967809 Fax: 86-573-87967851 sales@shinelight.cc
SHINELIGHT TECHNOLOGY CO., LTD
ELECTRICAL SPECIFICATIONS
Parameter Values Conditions
INPUT
AC Voltage 90 ~ 305 Vac Operating Voltage
Frequency Range 47 ~ 63 Hz
AC Current (110V input) 1.25 A Full load
AC Current (220V input) 0.61 A
Inrush Current 65 A Cold start, Vin=230V
Leakage Current 0.75 mA Vin=277V, 50Hz
OUTPUT
Top Output Power 120 W
Set-up Delay Time 0.8 ~ 1.2 s
Line Regulation 1%
Load Regulation 3%
PROTECT
Over Voltage Protect
1.3 Vo ±5% floating deviation
Hiccup mode. The power supply shall return to normal
operation only after the power is turn-on again.
Short Circuit Protect
No damage shall occur when any output operating in a
short circuit condition. The power supply shall be
self-recovery when the fault condition is removed.
Over Temperature Protect 110°C
NOTE: 1. All specifications except “OTP” are measured at 25°C.
SAFETY & EMC COMPLIANCE
Parameter Standards
Safety UL/c-UL, CE UL8750, UL935, UL1012, CSA-C22.2 No.107.1
EN61347-1, EN61347-2-13
EMI EN55015
EMS
EN61000-3-2, EN61000-3-3, EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6, EN61000-4-8, EN61000-4-11, EN61547
PRODUCTS INFORMATION
Parameter Values
Working Temp., Humidity -35°C ~ +70°C; 10 ~ 100% RH non-condensing
Storage Temp., Humidity -40°C ~ +85°C; 5 ~ 100% RH
www.shinelight.cc Tel: 86-573-87967809 Fax: 86-573-87967851 sales@shinelight.cc
SHINELIGHT TECHNOLOGY CO., LTD
MTBF 275,000 hours
Life Time 82,000 hours
Dimension (L*W*H)
SHC120-****SW-C 6.24(7.42)*3.07*1.46 inch;
158.5(188.5)*78.0*37.0 mm
SHC120-****SW-E 6.24(7.26)*3.43*1.56 inch;
158.5(184.5)*87.0*39.5 mm
Net Weight SHC120-****SW-C 900 g
SHC120-****SW-E 1000 g
APPLICATION NOTES
I DERATING CHARACTER
II POWER FACTOR CHARACTERS
III EFFICIENCY CHARACTERS
IV TOTAL HARMONICS DISTORTION
V LIFE TIME vs Tc/Ta
www.shinelight.cc Tel: 86-573-87967809 Fax: 86-573-87967851 sales@shinelight.cc
SHINELIGHT TECHNOLOGY CO., LTD
MECHANICAL SPECIFICATIONS
ENCAPSULATION I SHC120-****SW-C / SHT120-****SW-C
SHD120-****SW-C
SHP120-****SW-C
www.shinelight.cc Tel: 86-573-87967809 Fax: 86-573-87967851 sales@shinelight.cc
SHINELIGHT TECHNOLOGY CO., LTD
ENCAPSULATION II SHC120-****SW-E / SHT120-****SW-E
SHD120-****SW-E
www.shinelight.cc Tel: 86-573-87967809 Fax: 86-573-87967851 sales@shinelight.cc
SHINELIGHT TECHNOLOGY CO., LTD
SHP120-****SW-E
www.shinelight.cc Tel: 86-573-87967809 Fax: 86-573-87967851 sales@shinelight.cc
SHINELIGHT TECHNOLOGY CO., LTD
DIMMING FUNCTION
I 0-10V ANALOG DIMMING – for SHD***-**** MODELS
LED Driver V
0-10V INPUT
(purple)
0-10Vdc
GND (gray)
Mode 1:0-10Vdc Input on Dimming Control
LED Driver
0-10V INPUT
(purple)
Rx
GND (gray)
Mode 2:External Resistor on Dimming Control
Parameter Values Conditions
Absolute Max. Voltage 0 ~ 12 V Normal 10~11V
0-10V Input Source Current 0 ~ 10 mA
NOTE: 1.If the dimming function is not used, short 10V output pin (yellow) and 0-10V input pin
(purple).
2. Io is actual output current and Ir is rated current without dimming control.
3. For the driver to operate properly, the load voltage must be maintained above the minimum
voltage threshold, proximally 50% of the max. output voltage for any given mode.
4. The dimming signal is allowed to be less than 1V, when it for 0-1V, the output current can
maintain about 10%Ir, however, the connected LEDs may flicker. Keeping dimming voltage
greater than 1V in application is strongly recommended.
5. Do not connect the GND of dimming to the output. Otherwise, the LED driver can not work
normally.
II PWM DIMMING– for SHP***-**** MODELS
Parameter Values Conditions
www.shinelight.cc Tel: 86-573-87967809 Fax: 86-573-87967851 sales@shinelight.cc
SHINELIGHT TECHNOLOGY CO., LTD
Input Voltage 0~10 V Purple wire.
Input Current 10 mA
PWM Frequency 0.5 ~ 3 kHz
PWM Pulse Width 10%~100%
NOTE: 1. Pulse width less than 10% will cause the driver working unsteadily.
III TIMER DIMMING for SHT***-**** MODELS
NOTE: 1.The dimming time of the chart is for reference only, it can be adjusted according to the
client's requirement.
Recommended