View
6
Download
0
Category
Preview:
Citation preview
ScreenLogic Wireless Connection Kit Installation Guide
Installation Guide
ScreenLogic™Wireless Connection Kit
pool/spa control system
ScreenLogic Wireless Connection Kit Installation GuideP/N 520663 - Rev B
ScreenLogic Wireless Connection Kit Installation Guide
Technical Support
Contact Technical Support at:
Sanford, North Carolina (8 A.M. to 5 P.M.)
Phone: (800) 831-7133
Fax: (919) 566-8920
Moorpark, California (8 A.M. to 5 P.M.)
Phone: (800) 831-7133
Fax: (800) 284-4151
Web sites: visit www.pentairpool.com and www.staritepool.com
Related IntelliTouch Manual
IntelliTouch ScreenLogic User’s Guide (P/N 520493)
© 2006 Pentair Water Pool and Spa, Inc. All rights reserved.
1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-800010951 West Los Angeles Ave., Moorpark, CA 93021 • (805) 523-2400
This document is subject to change without notice.
Trademarks and Disclaimers. The trademark IntelliTouch is a registered trademark of PentairWater Pool and Spa, Inc. ScreenLogic is a trademark of Pentair Water Pool and Spa, Inc. Othertrademarks and trade names may be used in this document to refer to either the entitiesclaiming the marks and names or their products. Pentair Water Pool and Spa, Inc. disclaimsproprietary interest in marks and names of others.
P/N 520663 - Rev B 06/22/06
ScreenLogic Wireless Connection Kit Installation Guide
8
Step 2:Connect the ScreenLogic Indoor Wireless Transceiver to theScreenLogic Protocol Adapter
To connect the ScreenLogic indoor wireless transceiver to theScreenLogic Protocol adapter:
1. Using the provided connection cable, connect one end of thecable to the ScreenLogic Protocol adapter and the other endto the ScreenLogic indoor wireless transceiver. The cableplugs are keyed for easy connection.
2. Plug the ScreenLogic Wireless Connection transceiver ACadapter wall-plug into an AC grounded electrical outlet.
ScreenLogic ProtocolAdapter
1 ft. connection cable(provide in kit)
ScreenLogic indoor wirelesstransceiver
Protocol Adapter <----------> Indoor wireless transceiverRED (Pin 4) <----------> RED (Pin 1)YELLOW (Pin 3) <----------> GREEN (Pin 2)GREEN (Pin 2) <----------> YELLOW (Pin 5)BLACK (Pin 1) <----------> BLACK (Pin 6)
Wiring Configuration
Protocol Adapter
LA
N
LABEL P/N 520535
RE
SE
T
SERI
AL C
ONNE
CTIO
N
Blac
k G
reen
Yello
w R
ed
P/N 520489
ScreenLogic Wireless Connection Kit Installation Guide
Contents
i
Introduction ........................................................................................... 1
ScreenLogic Wireless Connection Kit Contents ..................................... 1
In this Installation Guide ....................................................................... 1
Summary installation steps ................................................................... 1
Step 1: Mount the Outdoor Wireless Transceiver and Connect to theIntelliTouch Load Center ........................................................................ 3
Step 2: Connect the Indoor Wireless Transceiver to the ScreenLogicProtocol Adapter ................................................................................... 8
FCC Regulatory Safety Notice - This equipment has been tested and found tocomply with the limits for a Class B digital device, pursuant to Part 15 of the FCCRules. These limits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or television reception, whichcan be determined by turning the equipment off and on, the user is encouraged to tryto correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.• Modifications not expressly approved by the party responsible for FCC
compliance could void the user’s authority to operate the equipment.
ScreenLogic Wireless Connection Kit Installation Guide
7. After the connection has been completed, close the controlpanel into its original position and secure it with the twoaccess screws.
8. Install the front panel and secure it with the two retainingscrews.
9. Close the Load Center front door. Fasten the two springlatches.
10. Switch the power on to the IntelliTouch Load Center.
11. Proceed to the “Connect the ScreenLogic IndoorWireless Transceiver to the ScreenLogic ProtocolAdapter” on page 8.
7
Personality board COM PORT Pin configuration
Note: Install the ScreenLogic outdoor wirelesstransceiver within 10 feet from Load Center
1 DNG KLB
2 TD- NRG
3 TD+ LEY
4 V51 DER
COM PORT screwterminal connector onPersonality board
Transceiver caseBlack
Transceiver Connector(see page 4 for details)
GreenRed Yellow
1 2 5 6
BLKGRNYELRED
ScreenLogic Wireless Connection Kit Installation Guide
IntroductionYour ScreenLogic Wireless Connection kit consists of two wireless900 Mhz transceivers which provides a wireless connectionbetween the ScreenLogic Protocol adapter and the IntelliTouchLoad Center located at the equipment pad. This wirelessconnection eliminates the existing hard wire connection from insideyour home to the equipment pad.
ScreenLogic Wireless Connection Kit ContentsThe following items are included in the Wireless Connection kit. If anyitems are missing please contact Technical Support.
• One ScreenLogic indoor wireless transceiver with AC poweradapter and one foot connection cable with attached plugs.
• One ScreenLogic outdoor wireless transceiver with 10 footattached cable
• ScreenLogic Wireless Connection Installation Guide(this manual)
In this Installation GuideUse the information in this manual for installing the WirelessConnection kit contents.
• For ScreenLogic system operating instructions, refer to theScreenLogic User’s Guide (P/N 520493)
Summary installation stepsThe ScreenLogic connection diagram on page 2 shows the transceiverlocations and connections. To install the ScreenLogic WirelessConnection kit:
• Mount the transceiver antenna near the IntelliTouch LoadCenter and connect the transceiver to the Personality board(COM port) located in the IntelliTouch Load Center.
• Connect the ScreenLogic indoor wireless transceiver to theScreenLogic Protocol adapter. Plug the transceiver ACpower adapter into an AC wall-outlet and into the transceiverunit to power up the unit.
1
ScreenLogic Wireless Connection Kit Installation Guide
5. Route the four conductor transceiver connection cable intothe lower plastic grommet, up through the low voltageraceway to the Personality board.
6. Strip back the cable conductors ¼ in. Insert the wires into thescrew terminals of the COM PORT plug located on thePersonality board as shown below. Using a smallflat-blade screwdriver, secure the wires with the screws.Make sure to match the color coding of the four wires:
Pin 4 - Red = +15Pin 3 - Yellow = +DTPin 2 - Green = -DTPin 1 - Black = GND
6
Note: If necessary, multiple wiresmay be inserted into a singlescrew terminal.
IntelliTouch Personalityboard COM PORTS
(J7/J8) screw terminalconnector
Raceway
Control panelPersonality
board
ScreenLogic Wireless Connection Kit Installation Guide
12
34
WA
N
RJ11
RJ45
INT
ER
NE
T
12
34
WA
N
- L
AN
-
Exi
stin
g w
ired
orw
irele
ss r
oute
r(m
an
da
tory
)R
J11
for
DS
LC
oax
for
Cab
le
In-w
all
Touc
hS
cree
n
Wir
eles
s tr
ansc
eive
rco
nnec
ted
toP
erso
nalit
y bo
ard
(CO
M p
ort)
via
10’ c
able
Pro
toco
lA
dapt
er
Scr
eenL
ogic
Wire
less
rou
ter
Wire
less
Dig
ital T
able
tW
irele
ss P
DA
Indo
or C
ontr
olP
anel
(*)
Exi
stin
g P
C
Eth
erne
t cab
le (R
J45
- CAT
5)
Eth
erne
t ca
ble
(RJ4
5 -
CAT
5)
DS
L or
Cab
le M
odem
(RJ4
5)
Cab
le d
ista
nce
limits
:-
Eth
erne
t ca
ble
dist
ance
lim
it =
300
fee
t-
Fou
r-w
ire c
able
dis
tanc
e lim
it =
150
0 fe
etN
ote:
(*)
Opt
iona
l wiri
ng f
or e
xist
ing
Indo
orC
ontr
ol P
anel
. Tap
into
the
Ind
oor
Con
trol
Pan
el c
onne
ctor
or
pig
tail
off
the
four
-wire
cabl
e co
nnec
ted
to t
he P
erso
nalit
y bo
ard.
Tra
nsc
eiv
er
conn
ecte
d to
Scr
eenL
ogic
Pro
toco
l ad
apte
r
Load
Cen
ter
(Loc
ated
out
side
at
equi
pmen
t pa
d)
2
4-w
ire 1
foo
tca
ble
AC
pow
erad
apte
rScreenLogic Wireless Connection Kit Installation Guide
WARNING Switch OFF the main system power to the Load Centerbefore making any connections.
1. Unlatch the two front door spring latches, and open the door.
2. Remove the two retaining screws securing the high voltagecover-panel, and remove it from the load center enclosure.
3. Loosen the two access screws securing the control panel andfold it down.
5
Panel retainingscrew
(Cover-panelnot shown)
Accessscrew
Retainingscrew
Accessscrew
Control panel
Connect the Transceiver connection cable to the Personality board
IntelliTouch Load Center
4. With the control panel in the open position, you can accessthe Personality board connectors.
ScreenLogic Wireless Connection Kit Installation Guide
3
Step 1: Mount the Outdoor Wireless Transceiver and Connectto the IntelliTouch Load Center
The following describes how to mount the outdoor transceiver at alocation near the IntelliTouch Load Center and connect the four-wire cable to the Personality board located in the IntelliTouch LoadCenter.
Mount the Transceiver module
The Transceiver is a two-way radio device with an attached antennathat communicates to and from the IntelliTouch system. Mount thetransceiver at a convenient location (on a flat vertical surface) near theload center, at a minimum of 5 ft. above ground level to optimize thetransmit and receive operating range. To avoid signal interference,mount the transceiver 10 feet away from the IntelliTouch Load Center,any metal surface/structure, or air blower located in the immediate areaof the equipment pad.
1. Slide the transceiver case off the back plate. The transceivercable is routed through the lower exit hole (right side) at thebottom of the back plate. The connector on the other end ofthe cable plugs into the transceiver board. Open the plasticbag inside the case and remove the transceiver antenna andtransceiver case screws, and set them aside.
2. Position the back plate against the mounting surface so thatthe transceiver is oriented in an upright position (with theantenna pointing upwards). Use a pencil to mark the fourmounting points. Drill four 3/16 in. diameter holes into themounting surface.
3. Position the back plate (with attached connection wire) overthe mounting points and secure it with four screws.
4. CAUTION - Electrostatic Discharge (ESD): Hold thecircuit board from the edges. Do not touch the boardcomponents, electrostatic discharge can damage theboard. Carefully remove the transceiver circuit board fromits bag. While holding the transceiver circuit board on itsedges, screw the antenna on the board threaded post. Do notover tighten.
5. Carefully connect the connection cable plug onto thetransceiver circuit board.
ScreenLogic Wireless Connection Kit Installation Guide
Transceiver Module
4
6. Position the transceiver circuit board with antenna into the mountedback plate. Align the board to the left side of the back plate.
7. Slide the case over the circuit board and antenna into the back plate.You may need to reposition the transceiver board inside the case tofully close the case. Secure the circuit board in the case using thetwo retaining screws provided in the plastic bag.
8. Proceed to “Connect the Transceiver connection cable to the Personalityboard” on page 5.
Transceiver circuit board
Back plate
Retaining screws
Case
Cable exits from lower exithole (right side)
Antenna
Mounting point (4x)
Circuit board threaded post
BlackGreen
Red Yellow
Screw terminalconnector (4-wirecable connects tothe IntelliTouchPersonality board)
1 2 5 6
Pin numbers
Recommended